A-Link | WNAP4G | A-Link WNAP(c)

WNAP 3G MOBILE ROUTER
Quick Installation Guide
Quick Installation Guide of WNAP 3G Mobile Router
※ To avoid users without access right through your WNAP 3G Mobile Router, it is suggested to change WLAN SSID
and password and admin password for web configuration login.
P
reparatio
n
1
2
At lease one PC with IEEE802.11b/g/n WLAN client or 10/100Mb Ethernet adapter installed.
One straight-through Category 5 Ethernet cable, used to link WAN interface to xDSL or CM for Internet connection or 3G
USB modem for your 3G Internet connection.
3
WNAP 3G Mobile Router.
Check package contents:
 WNAP 3G Mobile Router
 DC Power Adapter

User’s manual CD-ROM

1.8M RJ-45 Cable Line (Option)
Collect Installation Information:
WAN configuration (Contact your ISP or network administrator for these information’s below)
•
•
DHCP Client
Static IP
IP Address
Subnet Mask
Default Gateway
DNS Address
PPPoE
User Name
Password
PPTP
IP Address
Subnet Mask
Server IP Address
User Name
Password
L2TP
IP Address
Subnet Mask
Server IP Address
User Name
Password
GSM 3.5G
3.5G Device
 .  .  . 
 .  .  . 
 .  .  . 
 .  .  . 
 .  .  . 
 .  .  . 
 .  .  . 
 .  .  . 
 .  .  . 
 .  .  . 
2 of 10
Quick Installation Guide of WNAP 3G Mobile Router
APN
PIN
LAN configuration
IP Address
Subnet Mask
WLAN configuration
SSID
Mode
Channel Number
 .  .  . 
 .  .  . 
USB Parts and Functions of WNAP 3G Mobile Router:
Panel Description
LAN LED
WPS LED
WAN LED
LED Indicator
1. PWR LED
2. WLAN LED
3. WPS LED
4. WAN LED
5. LAN LED
WLAN LED
Power LED
State
On
Description
The WNAP 3G Mobile Router is powered on.
Off
Flashing
Off
Flashing
Off
Flashing
On
Off
Flashing
On
Off
The WNAP 3G Mobile Router is powered off.
WLAN is active
WLAN is off
The WPS feature is Enabled.
The WPS feature is Disabled.
Data is transmitting or receiving on the WAN
Port linked.
No link.
Data is transmitting or receiving on the LAN
Port linked.
No link.
3 of 10
Quick Installation Guide of WNAP 3G Mobile Router
WPS
Reset
USB
Interfaces
Antenna (SMA)
PWR (Power)
LAN
WAN
WPS
USB
RS (Reset)
WAN
LAN
Power
Description
The Wireless LAN Antenna.
The power jack allows an external DC power supply
connection.
The external DC adaptor provide adaptive power requirement
to the WLAN Broadband Router.
The RJ-45 sockets allow LAN connection through Category 5
cables. Support auto-sensing on 10/100M speed and half/ full
duplex; comply with IEEE 802.3/ 802.3u respectively.
The RJ-45 socket allows WAN connection through a Category
5 cable. Support auto-sensing on 10/100M speed and half/ full
duplex; comply with IEEE 802.3/ 802.3u respectively.
Push continually the reset button 5 ~ 10 seconds to enable the
WPS feature.
The USB port allows you to connect 3G USB modem for
Internet connection or USB Storage connection to support FTP
server, File server.
Push continually the reset button 5 ~ 10 seconds to reset the
configuration parameters to factory defaults.
4 of 10
Quick Installation Guide of WNAP 3G Mobile Router
In
stallatio
n
Step One – Power On WNAP 3G Mobile Router
Connect DC Power Adapter to WLAN Broadband Router and the wall power socket.
Notice: It will take about 50 seconds to complete the boot up sequence after powered on
the WNAP 3G Mobile Router; Power LED will be active, and after that the
WLAN Activity LED will be flashing to show the WLAN interface is enabled
and working now.
Step Two – Configure WNAP 3G Mobile Router
1. Connect your PC to LAN port for configuration setting. WNAP 3G Mobile Router is delivered with
the following factory default parameters on the Ethernet LAN interfaces.
 Default IP Address: 192.168.1.254
 Default IP subnet mask:
255.255.255.0
 WEB login User Name: admin
 WEB login Password: admin
 Configure your PC with IP address
between 192.168.1.1 to 192.168.1.253
and subnet mask to be 255.255.255.0,
then open an Internet browser (i.e.
Microsoft IE6.1 SP1 or above) to
connect WNAP 3G Mobile Router by
entering http://192.168.1.254 to URL
field.
The following example is to configure router as “Gateway” mode that use factory default value.
You may change those values if you think that is necessary.
5 of 10
Quick Installation Guide of WNAP 3G Mobile Router
2. Click “Setup Wizard” in submenu of Site contents
Click “Next>>”
button to go next.

3. Configure Operation Mode
 Click “Gateway”.
 Click “Next>>” button to
go next.
6 of 10
Quick Installation Guide of WNAP 3G Mobile Router
4. Configure Time Zone Setting configuration
Click “Next>>”
button to go next.

5. Configure LAN Interface Setup
IP Address:
192.168.1.254.
 Subnet Mask:
255.255.255.0.
 Click “Next>>”
button to go next.

6. WAN Interface Setup
WAN Access Type:
Select WAN connection of
ISP provides.
 WAN Options: Static

IP,
DHCP Client, PPPoE,
PPTP, L2TP, GSM 3.5G
 Click “Next>>”
button to go next.
7 of 10
Quick Installation Guide of WNAP 3G Mobile Router
7. Wireless Basic Settings
Band: 2.4GHz(B+G)
Mode: AP
Network Type: disabled
SSID: WNAP
Channel: Auto
Enable Mac Clone: disabled
Click “Next>>” button to go
next.







8. Wireless Security Setup
Encryption: WPA2 Mixed
Options:
None, WEP, WPA (TKIP), WPA2
(AES), WPA2 Mixed
Click “Finished” button to
close setup session.

8 of 10
Quick Installation Guide of WNAP 3G Mobile Router
Step Three – Connect WLAN client to WNAP 3G Mobile Router wirelessly
On your wireless client PC:
1. Move your mouse to
the Network icon on the
Task bar and right click
the mouse button to bring
up the pop-up menu.
2. Click the View
Available Wireless
Networks on the pop-up
menu.
2
1
3. Select the specific
WLAN network (SSID)
from the Available
Networks list.
3
4
9 of 10
4. Click the Connect
button to establish the
communication link to the
wireless network
Quick Installation Guide of WNAP 3G Mobile Router
Ethernet
Cable
Internet
Ethernet cable
xDSL/ CM
Power adapter
The wireless network diagram of WNAP 3G Mobile Router..
R
eferen
ce
Please consult the user’s manual of WNAP 3G Mobile Router for detailed and complete operation guide.
Product is in accordance with directive 1999/5/EY
(CE).
WNAP(c) EAN: 64 18949 02217 7
Product importer, repairs and technical support :
A-Link Europe Ltd, Kylävainiontie 20, FI-02760 Espoo, Finland
Technical support : +358-600-41020 (2,70€ / min + local network fee)
Internet : http://www.a-link.com
E-mail : techsupport@a-link.com
All rights reserved
Copyright © 2011 A-link Europe Ltd
10 of 10
11c24T WNAPc QIG
Download PDF

advertising