AT&T | E2903B | User`s manual | AT&T E2903B User`s manual

User’s manual
E2903B
2.4 GHz cordless telephone
with caller ID/call waiting
Congratulations
on purchasing your
new AT&T product.
Before using this AT&T product, please
read the Important safety instructions
on pages 45-47 of this manual.
Please thoroughly read the user’s
manual for all the feature operation
and troubleshooting information you
need to install and operate your new
AT&T product. You can also visit our
website at www.telephones.att.com
or call 1 (800) 222-3111.
In Canada dial 1 (866) 288-4268.
Model #:
E2903B
Product name: 2.4GHz cordless telephone
Serial #:
(found on the bottom of the telephone base)
Purchase date:
Place of purchase:
© 2007 Advanced American Telephones. All rights reserved.
AT&T and the AT&T logo are trademarks of AT&T Knowledge Ventures,
licensed to Advanced American Telephones.
You must install and charge
the battery before using the
telephone.
STOP!
See page 7
for easy instructions.
For customer service or product information, visit our website at www.telephones.att.com or
call 1 (800) 222-3111. In Canada dial 1 (866) 288-4268.
CAUTION: To reduce the risk of fire or injury to persons or damage to the telephone, read
and follow these instructions carefully:
• Use only the supplied rechargeable battery or replacement battery (model 27910, part number 89-009900-00) or equivalent. To order a replacement battery, visit our website at www.telephones.att.com or call
1 (800) 222-3111. In Canada dial 1 (866) 288-4268.
• Do not dispose of the battery in a fire. Like other batteries of this type, it could explode if burned. Check
with local codes for special disposal instructions.
• Do not open or mutilate the battery. Released electrolyte is corrosive and may cause damage to the eyes
or skin. It may be toxic if swallowed.
• Exercise care in handling batteries in order not to create a short circuit. Do not allow conductive materials
such as rings, bracelets, or keys to touch the battery. The battery or conductor may overheat and cause
harm.
• Charge the battery provided with or identified for use with this product only in accordance with the
instructions and limitations specified in this manual.
• Observe proper polarity orientation between the battery and battery charger.
• Do not disassemble your telephone. There are no user-serviceable parts inside. Refer to qualified service personnel for servicing.
User's manual
E2903B
2.4 GHz cordless telephone
with caller ID/call waiting
Table of contents
Getting started
Appendix
Quick reference guide.......................2
Parts checklist.......................................4
Telephone base installation............5
Battery installation & charging.............7
Installation options.............................8
Belt clip & optional headset.............10
Screen icons, indicator lights
& tones................................................35
Handset display screen
messages..........................................36
Troubleshooting................................. 38
Important safety instructions...... 45
FCC Part 68 & ACTA........................ 48
FCC Part 15......................................... 50
Limited warranty............................... 51
Technical specifications................. 54
Index........................................................ 55
Telephone operation
Basic operation.................................. 11
Options while on calls.................... 14
Intercom .............................................. 16
Intercom call transfer..................... 17
Settings.................................................. 18
Sounds.................................................... 21
Display.................................................... 22
Ringer volume.................................... 24
Directory
Directory................................................ 25
New directory entries..................... 26
Directory search................................ 28
To dial, delete or edit entries............. 30
Caller ID operation
Caller ID operation........................... 31
To review the call log..................... 34
Getting started
Quick reference guide
Cordless handset
MENU�������
/������
SELECT
CID/-VOLUME
Press to display the menu. Once in
the menu, press to select an item
or save an entry or setting.
Press to scroll down while in
menus. Press to display caller
ID information (page 34). While
entering names or numbers,
press to move the cursor to the
left (page 27). Press to decrease
the listening volume while on a
call (page
����������
14)�.
DIR
Press to scroll up while in menus.
Press to display directory entries
(page 28). While entering names or
numbers, press to move the cursor
to the right (page
��������������������
27)�����������
. Press to
increase the listening volume while
on a call ����������
(page 14)�.
PHONE/FLASH
Press to make or answer a call
(page 11). During a call, press to
receive an incoming call if call
waiting is activated (page 14).
OFF/CLEAR
During a call, press to hang up.
While using menus, press to cancel
an operation, back up to the previous
menu, or exit the menu display.
While predialing, press to delete
digits (page 11).
MUTE�������
/DELETE
While on a call, press to mute
microphone (page 15). While
reviewing the call log, press
to delete an individual entry,
or press and hold to clear the
caller ID log (page 34). While
entering or editing a name or
number, press to delete a character (page 27).
SPEAKER
REDIAL/PAUSE
TONE
MUTE
REDIAL
DELETE
PAUSE
Press to initiate an intercom conversation between handsets. Press
to transfer a call (pages 16-17).
Feature menu
DIRECTORY
Press to view redial memory (page
12). While entering numbers,
press and hold to insert a dialing
pause (page 26).
INT
Press to activate handset speakerphone. Press again to resume
normal handset use (page 11).
Shows a highlighted item
Feature menu
Using menus
DIRECTORY..................Page 25
Press
CID/-VOLUME or
DIR /VOLUME+ to scroll
through menu items.
CALL LOG....................Page 31
SETTINGS......................Page 18
SOUNDS.......................Page 21
DISPLAY........................Page 22
Menu
/VOLUME+
RINGER VOLUME......Page 24
Press MENU/SELECT to select or
modify a highlighted item.
Press OFF/CLEAR to cancel an
operation, back up to the previous
menu, or exit the menu display.
Getting started
Quick reference guide
Telephone base
CHARGE/IN USE
•
On when the cordless handset is
properly positioned to charge in
the telephone base.
•
Flashes during an incoming call’s
ringing.
•
Flashes when the handset is in use,
or when another telephone is in
use on the same line.
VOICEMAIL
Flashes when there are new voicemail (requires voicemail service from
your local telephone company).
HANDSET LOCATOR
Press to make the handset beep
(page 13).
Getting started
Parts checklist
Save your sales receipt and original packaging in case it is necessary to ship
your telephone for warranty service.
Check to make sure the telephone package includes the following:
User’s manual
Quick start guide
E2903B
2.4 GHz cordless telephone
with caller ID/call waiting
E2903B
2.4 GHz cordless telephone
with caller ID/call waiting
TONE
User's manual
Quick start guide
Chargers for cordless handset
Power adapter
for telephone
base
TONE
TONE
MUTE
REDIAL
MUTE
REDIAL
MUTE
REDIAL
DELETE
PAUSE
DELETE
PAUSE
DELETE
PAUSE
Telephone base with
mounting bracket
installed
Cordless handsets
Batteries for cordless handsets
Power adapters for
handset charger
Battery compartment covers
Belt clips for cordless handsets
Telephone line cord
Getting started
Telephone base installation
Choose a central location close to a telephone jack and an electrical outlet
not connected to a wall switch. The telephone base can be placed on a flat
surface or mounted on a standard wall plate. For optimum range and better
reception, place the telephone base in a high and open location.
Avoid placing the telephone base too close to:
• Communication devices such as: personal computers, computer routers, television sets, VCRs, wireless routers (wireless broadband, wi-fi, or 802.11) or
other cordless telephones.
• Excessive heat sources.
• Noise sources such as a window with traffic outside, motors, microwave
ovens, refrigerators, or fluorescent lighting.
• Excessive dust sources such as a workshop or garage.
• Excessive moisture.
• Extremely low temperature.
• Mechanical vibration or shock such as on top of the washing machine or
work bench.
Getting started
Telephone base installation
1. Plug one end of the telephone
line cord into the telephone jack at
the bot­tom of the telephone base.
2. Plug the small end of the power
adapter into the power jack at the
bottom of the telephone base.
5
4
3. Route cords through slots.
Telephone line cord
4. Plug the large end of the power
adapter into an electrical outlet
not controlled by a wall switch.
DSL filter
(Optional for DSL users,
see number four in the
note section below.)
5. Plug the other end of the telephone
line cord into a telephone jack.
3
2
1
NOTES:
1. Use only the power adapter supplied with this product. To order a replacement power adapter, visit
our website at www.telephones.att.com or call 1 (800) 222-3111. In Canada dial 1 (866) 288-4268.
2. Be sure to use an electrical outlet not controlled by a wall switch.
3. This power unit is intended to be correctly oriented in a vertical or floor mount position. The prongs
are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet
outlet.
4. If you receive high speed internet through your telephone line (commonly referred to as DSL), and
you are experiencing interference during telephone conversations and/or your caller ID features
are not functioning properly, install a DSL filter to the telephone line between the telephone base
and the telephone wall jack. Contact your DSL service provider for a DSL filter.
Getting started
Battery installation & charging
After installing the battery, you may be able to make and receive short calls.
For best performance, place the handsets in the telephone base or the charger and charge for 16 hours before use.
You can keep the battery charged by returning the handsets to the telephone
base or the charger after use. When the battery is fully depleted, a recharge
takes about 12 hours. The average talk time on a fully charged battery is
about eight hours, and the standby time is approximately five days. Actual
battery life depends on usage conditions and age of battery.
1. Plug the small end
of the smaller power
adapter into the jack
on the underside of
the charger, then route
the cord through the
slot as shown.
2. Plug the large
end of the smaller
power adapter into
an electrical outlet
not controlled by a
wall switch.
3. Insert the plug as
indicated. Be sure to
securely insert the
plug, making sure that
it matches the colorcoded label inside the
battery compartment.
6. You may be able to make and receive
short calls. For best performance, place
the handset in the telephone base or
charger to charge for at least 16 hours
before first use.
LOW BATTERY
TONE
MUTE
REDIAL
DELETE
PAUSE
Low battery indicator
Return the handset to the
telephone base or charger
to recharge when this symbol flashes. (Handset will
beep when battery is low.)
4. Place the
battery pack
and wires
inside the
compartment.
5. Slide the
battery compartment cover
up until it
clicks.
To replace the battery, press
in and downward on the tab
of the battery compartment
to open the battery compartment cover. Lift out the old
battery and disconnect it from
the handset. Follow the instructions on this page to install and
charge the new battery.
NOTE: Under normal conditions, the battery should last around one year. This may vary depending on usage.
Caution: Use only the supplied rechargeable battery or replacement battery (model 27910,
part number 89-0099-00-00) or equivalent. To order a replacement battery, visit our website at
www.telephones.att.com or call 1 (800) 222-3111. In Canada dial 1 (866) 288-4268.
Getting started
Installation options
NOTE: The mounting bracket must be used for both tabletop use and wall mounting positions.
Tabletop mount
Wall mount
Telephone outlet
mounting plate
with mounting
studs
Wall mounting
The telephone base comes with the bracket mounted for tabletop use. If wallmounting is desired, a telephone outlet wall mounting plate with mounting studs is
required. This mounting plate with studs may be available for purchase from many
hardware or consumer electronics retailers and may require professional installation.
1. To remove the bracket, hold the
telephone base in both hands, press
the two bracket tabs and lift the
bracket away from slots
and .
2. Connect the telephone line cord and
power adapter to the jacks on the bottom of the telephone base. Bundle the
telephone cord, and secure it with a
twist tie before placing it inside the
bracket.
Getting started
Installation options
3. To attach the bracket for wall mounting,
insert the tabs of the bracket into slots
and
on the telephone base, then press
the other bracket tabs into slots
and
as
shown on the right.
4. Plug the power adapter into an electrical
outlet not controlled by a wall switch. Plug
the telephone line cord into a telephone wall
jack. To mount the telephone on the wall,
position the mounting holes
and
over
the telephone outlet mounting studs. Press
and slide the bracket down firmly so the
telephone is held securely on the telephone
outlet mounting studs.
Telephone outlet mounting studs
Tabletop mounting
To return the bracket from the wall mount to tabletop position, follow the
directions below.
1. Remove the telephone base from the wall.
Unplug the cords from the wall jacks.
Remove the bracket from the telephone
base.
3. Route cords through slots. Plug the
other end of the telephone line cord
into a telephone wall jack. Plug the
large end of the larger power adapter
into an electrical outlet not controlled
by a wall switch.
2. Insert the bracket tabs into slots
and
on the telephone base,
then press the other bracket
tabs into slots and .
Getting started
Belt clip & optional headset
Install belt clip as shown below if desired.
Snap belt clip
into the notches
on both sides of
handset.
To release belt clip
from handset, lift one
side of the belt clip
out of the notch.
For hands-free telephone conversations, use any industry standard 2.5 mm headset
(purchased separately). For best results, use an AT&T 2.5 mm headset. To
order an AT&T 2.5 mm headset, visit our website at www.telephones.att.com
or call 1 (800) 222-3111. In Canada dial 1 (866) 288-4268.
Plug 2.5 mm headset into
the jack on the side of handset (beneath small rubber
cap).
NOTE: If the sound quality of the headset is not good, try unplugging it, and firmly plug-
ging it in again.
TONE
MUTE
REDIAL
DELETE
PAUSE
10
Telephone operation
Elapsed time
PHONE 00:00:30
TONE
MUTE
REDIAL
DELETE
PAUSE
PREDIAL
Basic operation
Making and answering calls
To answer an incoming call, press PHONE/FLASH,
SPEAKER or any dial pad key (0-9, * or #) on the
handset. To make a call, press PHONE/FLASH or
SPEAKER then dial a number. Press OFF/CLEAR
or place the handset in the telephone base or
charger to hang up.
To predial (preview numbers before dialing), enter
numbers first. Press MUTE/DELETE or OFF/CLEAR
anytime to make corrections, then press SPEAKER
or� PHONE/FLASH ��������
to dial.
The screen displays the elapsed time as you talk (in
hours, minutes and seconds).
555-1234
NOTE: During a call, pressing PHONE/FLASH to access services from your local telephone company will not affect the elapsed time.
SPEAKER 00:00:49
Hands-free speakerphone calls
To answer a call, press SPEAKER. To make a
call, press SPEAKER then dial a number. During
a call, press SPEAKER to alternate between
hands-free speakerphone and normal handset
use. Press OFF /CLEAR to hang up.
NOTE: If a headset is plugged into the handset, you will not be able to use the handset speakerphone. To use hands-free speakerphone, make sure the headset is unplugged, then press
SPEAKER to activate the hands-
free speakerphone.
11
Telephone operation
Basic operation
REDIAL
555-1234
RINGER MUTE
Last number redial
Press REDIAL/PAUSE to display the most recently
called numbers (up to 32 digits). Press CID/-VOLUME,
DIR /VOLUME+ or REDIAL/PAUSE repeatedly to view
up to five recently called numbers. The handset
beeps twice at the beginning or end of the list.
Press OFF/CLEAR to exit. Press SPEAKER or
PHONE/FLASH to redial any displayed number. Or
press PHONE/FLASH or SPEAKER then REDIAL/PAUSE
to dial the most recently called number (up to 32
digits).
Press MUTE/DELETE to delete the displayed number
from the redial memory.
Temporary ring silencing
Press OFF/CLEAR or MUTE/DELETE while the telephone
is ringing to silence the handset ringer temporarily.
This will silence the ringer without disconnecting
the call. The next incoming call will ring normally.
NOTE: All handsets will ring with an incoming call. Pressing
OFF/CLEAR or MUTE/DELETE on one handset will only silence the ringer of that particular handset but the other handset will continue to ring.
12
Telephone operation
Basic operation
Handset locator
If the handsets are misplaced, press HANDSET
LOCATOR on the telephone base. The handsets
will play a paging tone for 60 seconds to help you
locate them. To stop the paging tone, press PHONE/FLASH,
SPEAKER, or any dial pad key (0-9, *, or #) on
the handsets, or press HANDSET LOCATOR on
the telephone base.
NOTES:
1. If the handset ringer is set to off (0), the hanset locator
feature is not avaible on that handset (page 24).
2.������������������������
During a page, pressing OFF/CLEAR or MUTE/DELETE on the
handset (page 12), the ringer of that handset will be silenced,
but it will not cancel the page.
TONE
MUTE
REDIAL
DELETE
PAUSE
13
Telephone operation
Options while on calls
Volume control
Press CID/-VOLUME to decrease the volume.
Press DIR /VOLUME+ to increase the volume.
When changing the volume level, the new setting
is saved.
NOTE: The earpiece, hands-free speakerphone and headset listening volume are adjusted separately.
Call waiting
Volume
Flash
If you subscribe to call waiting service with your
local telephone company, there will be a beep if
there is an incoming call while you are already on a
call. Press PHONE/FLASH to put your current call
on hold and take the new call. Press PHONE/FLASH
anytime to switch back and forth between calls. For
more information on caller ID, see page 31.
TONE
MUTE
REDIAL
DELETE
PAUSE
Multiple handset use
While on a call, a person on the other handset can
press PHONE/FLASH or SPEAKER to join the
same conversation.
A person on either handset can press OFF/CLEAR,
or place the handset in the telephone base or
charger to drop out of the call, but the call will not
be terminated until both handsets hang up.
NOTE: When two handsets are used on the same outside call, the call transfer feature cannot be used (page 17).
14
Telephone operation
Options while on calls
Mute
Press MUTE/DELETE to silence the microphone. When
mute is on,
will show on the handset screen. You
will be able to hear the caller, but your caller will not
be able to hear you until you press MUTE/DELETE
again and resume speaking. When mute is turned
off, MICROPHONE ON will show temporarily on
the handset screen. Mute is automatically cancelled
when you end a call.
Tone
TONE
Mute
MUTE
REDIAL
DELETE
PAUSE
Temporary tone dialing
If you have only dial pulse (rotary) service, you can
temporarily switch to touch tone dialing during a call
by pressing TONE/*. This can be useful when sending tone signals for access to answering systems
or long distance services.
After you hang up or press PHONE/FLASH (to
receive a call waiting call), the telephone automatically returns to dial pulse (rotary) service.
15
Telephone operation
Intercom
HANDSET 1
Use the intercom feature for conversations between
handsets.
1. Press INT. The screen of the originating handset
will show INTERCOM TO:.
2. Enter the handset number of the destination handset (1,
2 or 3). The display will show CALLING HANDSET X.
The destination handset will ring, and its screen
will show HANDSET X IS CALLING.
12:45PM
NOTES:
INTERCOM TO:
•
Before the intercom call is answered, you can cancel the
intercom call by pressing OFF/CLEAR or INT.
•
If the destination handset is not answered within 100
seconds or if it is in the directory or call log mode, or out
of range, the originating handset will show the message
NOT AVAILABLE.
INTERCOM
3. On the ringing destination handset, press
PHONE/FLASH, INT, SPEAKER, or any dial pad key
(0-9, * or #) to answer the intercom call.
NOTE: At any time, a maximum of two hand-
sets can be used on an intercom call, and another handset can be used on an out-
side call at the same time.
NOTE: On the ringing destination handset, pressing OFF/CLEAR or MUTE/DELETE will temporarily silence the intercom ringer.
To end the intercom call:
• Press OFF/CLEAR or INT on either handset.
-OR• Place either handset in the charger or telephone base.
Handling incoming calls
The telephone will beep if you receive an outside call
during an intercom conversation. You can either:
• Press PHONE/FLASH to end the intercom call
and answer the incoming call.
-OR• Press INT or OFF/CLEAR to disconnect the intercom connection without answering the incoming
call. The incoming call will continue to ring.
16
Telephone operation
Intercom call transfer
Use the intercom feature to transfer an external
call from one handset to another.
PHONE 00:05:30
TRANSFER TO:
INTERCOM
1. During a conversation with an external call, press
INT. The external call is automatically placed on
hold. The originating handset’s screen will show
TRANSFER TO:.
2. Enter the handset number of the destination handset (1,
2 or 3). The display will show CALLING HANDSET X.
The destination handset will ring, and its screen
will show HANDSET X IS CALLING.
3. On the ringing destination handset, press
PHONE/FLASH, INT, SPEAKER, or any dial pad key
(0-9, * or #) to answer the intercom call. You can now
talk without the external caller hearing the conversation.
NOTES:
CALL TRANSFERRED
•
•
You can alternate between the intercom call and the outside call by pressing INT on the originating handset. The display will alternate between INTERCOM and OUTSIDE to indicate which party is active.
NOTES:
1. Before the intercom call is
answered, you can cancel
the transfer and return to
the external call by pressing
OFF/CLEAR, PHONE/FLASH,
or INT.
2. If the destination handset
does not answer the intercom
call within 100 seconds,
or if the other handset is
in the directory or call log
mode, or out of range, the
originating handset will
show NOT AVAILABLE on
its screen and will automatically return to the external
call.
•
•
You can end the intercom call and return to the external call by pressing PHONE/FLASH on the originating handset.
The person on the destination handset can join the external call by pressing PHONE/FLASH, connecting both handsets to the outside call.
To allow the person on the destination handset to join the external call, press and hold INT on the originating handset.
4. Complete the transfer by pressing OFF/CLEAR
on the originating handset or placing that handset
in the telephone base or charger. The originating
handset’s screen will show CALL TRANSFERRED
and the other handset will automatically be connected to the external call.
17
Telephone operation
Settings
In the SETTINGS menu, you can change the language, dial type, and clock setting. You can also
clear the voice mail indication.
DIRECTORY
SETTINGS
1.Press MENU/SELECT in idle mode to enter the
feature menu.
2.Press CID/-VOLUME to highlight SETTINGS, then
press MENU/SELECT to enter the SETTINGS menu.
3. Press CID/-VOLUME or DIR /VOLUME+ to scroll
through the SETTINGS menu, then press
MENU/SELECT to select the desired option.
SETTINGS
LANGUAGE
DIAL TYPE
CLOCK SETTING
To cancel an operation, back up to the previous
menu, or exit the menu display press OFF/CLEAR.
To return to the idle mode press and hold
OFF/CLEAR.
Language
In this menu, you can select the language used in
all screen displays.
SETTINGS
LANGUAGE
DIAL TYPE
CLOCK SETTING
LANGUAGE
ENGLISH
FRANCAIS
ESPANOL
1.In the SETTINGS menu, press CID/-VOLUME or
DIR /VOLUME+ to highlight LANGUAGE, then
press MENU/SELECT.
2.Press CID/-VOLUME or DIR /VOLUME+ to highlight
ENGLISH, FRANCAIS or ESPANOL.
3.Press MENU/SELECT to save your preference
and be returned to SETTINGS.
Dial type
SETTINGS
LANGUAGE
DIAL TYPE
CLOCK SETTING
DIAL TYPE
TONE
PULSE
In this menu, you can choose TONE or PULSE
(rotary service) dialing. The factory default setting
is TONE. Change this to PULSE only if you do not
have touch-tone dialing service.
1.In the SETTINGS menu, press CID/-VOLUME
or DIR /VOLUME+ to highlight DIAL TYPE, then
press MENU/SELECT.
2.Press CID/-VOLUME or
TONE or PULSE.
DIR
/VOLUME+ to
highlight
3.Press MENU/SELECT to save your preference
and be returned to SETTINGS.
NOTE: Changing the dial type on one handset will change the dial type on all registered handsets.
18
Telephone operation
Settings
Clock setting
DIRECTORY
SETTINGS
SETTINGS
LANGUAGE
DIAL TYPE
CLOCK SETTING
CLOCK SETTING
12:00AM
CLOCK SETTING
06:00AM
If you subscribe to caller ID service provided by
your local telephone company, the time will automatically be set by an incoming call.
In this menu, you can choose to set the time displayed on the handset screen.
To cancel an operation, back up to the previous
menu, or exit the menu display press OFF/CLEAR.
To return to the idle mode press and hold
OFF/CLEAR.
1.Press MENU/SELECT in idle mode to enter the
feature menu.
2.Press CID/-VOLUME to highlight SETTINGS, then
press MENU/SELECT to enter the SETTINGS menu.
3. Press CID/-VOLUME or DIR /VOLUME+ to highlight
CLOCK SETTING, then press MENU/SELECT.
4.Use the dial pad keys (0-9) to enter two digits
for the hour (01-12). You can also press
CID/-VOLUME or DIR /VOLUME+ to set the hour.
5.Press
CLOCK SETTING
06:45AM
MENU/SELECT.
6.Use the dial pad keys (0-9) to enter two digits
for the minute (00-59). You can also press
CID/-VOLUME or DIR /VOLUME+ to set the minute.
7.Press
8.Press
PM.
MENU/SELECT.
CID/-VOLUME
or DIR
/VOLUME+ to set AM or
9. Press MENU/SELECT to confirm the clock setting and
be returned to SETTINGS.
NOTE: Caller ID provides the time. The time will be set automatically only if you subscribe to caller ID service provided by your local telephone company (page 32).
19
Telephone operation
Settings
Clear voice mail indication
DIRECTORY
If you subscribe to voice mail services provided
by your local telephone company, NEW VOICE
MAIL and the
icon will appear on all handset
screens when you have new voice mail.
SETTINGS
To cancel an operation, back up to the previous
menu, or exit the menu display press OFF/CLEAR.
To return to the idle mode press and hold
OFF/CLEAR.
SETTING
DIAL TYPE
CLOCK SETTING
CLR VOICE MAIL
CLR VOICE MAIL
TURN INDICATOR
OFF?
To manually turn off the NEW VOICE MAIL message, the
icon and VOICEMAIL light:
1. Press MENU/SELECT in idle mode to enter the
feature menu.
2.�����
Press CID/-VOLUME to highlight SETTINGS, then
press MENU/SELECT to enter the SETTINGS
menu.
3.Press CID/-VOLUME or DIR
CLR VOICE MAIL.
4.Press
/VOLUME+ to
highlight
MENU/SELECT.
5.Press MENU/SELECT again to remove the displayed message, or press OFF/CLEAR to exit.
This only turns off the displayed NEW VOICE MAIL
message and the
icon on all cordless hand­set
screens. It does not delete the voice mail message(s).
Use this feature when the telephone indicates there
is voice mail when you have none, or when you have
accessed your voice mail from a different telephone
line (away from home). If there is actually a new
voice mail message, your local telephone company
will continue to send the signal which will cause the
NEW VOICE MAIL message and the
icon to be
displayed again.
NOTE: When you make a call a pulsing (stutter) dial tone may alert you to a voice mail message from your tele-
phone company.
20
Telephone operation
Sounds
In the SOUNDS menu, you can choose one of ten
ringer melodies, and turn the key tone on or off.
DIRECTORY
SOUNDS
To cancel an operation, back up to the previous
menu, or exit the menu display press OFF/CLEAR.
To return to the idle mode press and hold
OFF/CLEAR.
Ringer melody
To choose a ringer melody:
1.Press MENU/SELECT in idle mode to enter the
feature menu.
SOUNDS
RINGER MELODY
KEY TONE
RINGER MELODY
MELODY 0
MELODY 1
MELODY 2
2.Use the CID/-VOLUME or DIR /VOLUME+ keys to
highlight SOUNDS, then press MENU/SELECT to
enter SOUNDS menu.
3.Press MENU/SELECT again to select RINGER
MELODY.
4.Press CID/-VOLUME or DIR
melody options.
/VOLUME+
to hear the
5.Press MENU/SELECT to save your preference
and be returned to SOUNDS.
DIRECTORY
Key tone
The handset is preset to beep with each key
press. If you turn off the KEY TONE, there will be
no beeps when keys are pressed.
SOUNDS
To turn the KEY TONE on or off:
1.Press MENU/SELECT in idle mode to enter the
feature menu.
SOUNDS
RINGER MELODY
KEY TONE
KEY TONE
ON
OFF
2.Use the CID/-VOLUME or DIR /VOLUME+ keys to
highlight SOUNDS, then press MENU/SELECT to
enter the SOUNDS menu.
3.Press CID/-VOLUME to highlight KEY TONE, then
press MENU/SELECT to select KEY TONE.
4.Press CID/-VOLUME or DIR
ON or OFF.
/VOLUME+
to highlight
5.Press MENU/SELECT to save your preference
and be returned to SOUNDS.
21
Telephone operation
Display
In the DISPLAY menu, you can select an image to
be displayed as wallpaper. You can also adjust the
contrast and brightness to one of five levels to
suit different lighting conditions.
To cancel an operation, back up to the previous
menu, or exit the menu display press OFF/CLEAR.
To return to the idle mode press and hold
OFF/CLEAR.
DIRECTORY
Wallpaper
To choose a wallpaper for the handset:
DISPLAY
DISPLAY
WALLPAPER
CONTRAST
BRIGHTNESS
1.Press MENU/SELECT in idle mode to enter the
feature menu.
2.Use the CID/-VOLUME or DIR /VOLUME+ keys to
highlight DISPLAY, then press MENU/SELECT to
enter the DISPLAY menu.
3.Press
MENU/SELECT
again to select WALLPAPER.
4. Press CID/-VOLUME or DIR
wallpaper options.
/VOLUME+
to see the
5. Press MENU/SELECT to save your preference and
be returned to DISPLAY.
Contrast
DIRECTORY
To adjust the screen contrast on the handset:
1.Press MENU/SELECT in idle mode to enter the
feature menu.
DISPLAY
DISPLAY
WALLPAPER
CONTRAST
BRIGHTNESS
CONTRAST
2.Use the CID/-VOLUME or DIR /VOLUME+ keys to
highlight DISPLAY, then press MENU/SELECT to
enter the DISPLAY menu.
3. Press CID/-VOLUME to highlight CONTRAST, then
press MENU/SELECT.
4. Press CID/-VOLUME or DIR
the screen contrast.
/VOLUME+ to
adjust
5. Press MENU/SELECT to save your preference and
be returned to DISPLAY.
22
Telephone operation
Display
DIRECTORY
DISPLAY
To cancel an operation, back up to the previous
menu, or exit the menu display press OFF/CLEAR.
To return to the idle mode press and hold
OFF/CLEAR.
Brightness
To adjust the screen brightness on the handset:
1. Press MENU/SELECT to enter the feature menu.
DISPLAY
WALLPAPER
CONTRAST
BRIGHTNESS
BRIGHTNESS
2. Press CID/-VOLUME or DIR /VOLUME+ to scroll to
DISPLAY, then press MENU/SELECT to enter
the DISPLAY menu.
3. Press CID/-VOLUME or DIR /VOLUME+ to highlight
BRIGHTNESS, then press MENU/SELECT.
4. Press CID/-VOLUME or DIR /VOLUME+ to view a
sample of each brightness level.
5. Press MENU/SELECT to save your preference and
return to DISPLAY.
NOTE: When the handset is idle and no keys have been pressed for 15 seconds, the handset display background will appear black to save battery power.
23
Telephone operation
Ringer volume
DIRECTORY
RINGER VOLUME
RINGER VOLUME
In this menu, you can set the ringer volume level
(1-6), or turn the ringer off (0). When the ringer is
turned off, the
will appear on the handset screen.
The ringer volume level also determines the ringer
volume for intercom calls (page 16) and the paging tone when initiating the handset locator feature (page 13). If the ringer volume level is set to
off (0) on a handset, that handset is silenced for
all incoming calls and paging.
To cancel an operation, back up to the previous
menu, or exit the menu display press OFF/CLEAR.
To return to the idle mode press and hold
OFF/CLEAR.
To adjust the RINGER VOLUME:
1.Press MENU/SELECT in idle mode to enter the
feature menu.
2.Use the CID/-VOLUME or DIR /VOLUME+ keys to
highlight RINGER VOLUME, then press MENU/
SELECT to enter the RINGER VOLUME menu.
3. Press CID/-VOLUME or DIR
ringer levels.
/VOLUME+ to
hear the
4.Press MENU/SELECT to save your preference and
be returned to the feature menu.
24
Telephone operation
Directory
Shared directory
DIRECTORY
Pat Williams
555-1234
The directory is stored in the telephone base, and
is shared by all handsets. Changes made to the
directory on any one handset will be applied to
all.
NOTE: Only one handset can review the directory or
caller ID log at a time. If another handset attempts to enter the directory, it will display NOT AVAILABLE AT THIS TIME.
Memory capacity
The directory can store up to 50 entries. Each
entry can contain a number up to 32 digits, and a
name up to 16 letters. A convenient search feature can help you find and dial numbers quickly
(page 29).
If all memory locations are in use, the screen will
display LIST FULL. You will not be able to store a
new number until you delete an existing one.
Exiting the directory
Press OFF/CLEAR to cancel an operation, back
up to the previous menu, or exit the menu display.
Press and hold OFF/CLEAR to return to the idle
mode.
If you pause for too long while creating an entry,
the procedure will time out and you will have to
begin again.
25
Telephone operation
New directory entries
DIRECTORY
To cancel an operation, back up to the previous
menu, or exit the menu display press OFF/CLEAR.
To return to the idle mode press and hold
OFF/CLEAR.
To create and store a new directory entry
DIRECTORY
REVIEW
STORE
DIRECTORY
ENTER NUMBER
555-1234
1.Press MENU/SELECT in idle mode to enter the
feature menu.
2.Press MENU/SELECT again to enter the
DIRECTORY menu.
3.Press
4.Press
CID/-VOLUME to
highlight STORE.
MENU/SELECT.
5. Enter the telephone number when prompted.
• Use the dial pad to enter up to 32 digits.
– Press CID/-VOLUME or DIR /VOLUME+ to move the cursor to the left or right.
– Press
MUTE/DELETE
to erase numbers.
– Press and hold REDIAL/PAUSE to enter a three-second dialing pause, (a p appears on the screen), if you need to pause for accessing banking or long distance
services.
-OR• Copy a number from redial by pressing REDIAL/PAUSE then press CID/-VOLUME or
DIR /VOLUME+ to locate the number to copy. Press MENU/SELECT to copy the number.
6.Press MENU/SELECT to save the number. The
display will show ALREADY SAVED if the
number is already in the directory.
NOTE: Each line can hold 16 digits, so if you enter a number longer than 16 digits, the numbers will be dis-
played in the following line.
26
Telephone operation
New directory entries
7. Enter the name when prompted.
DIRECTORY
ENTER NAME
Pat Williams
NOTE: The handset will automatically
capitalize the first
letter of every word.
• Use the dial pad to enter a name (up to 16 characters). Each time a key is pressed, the character on that key will be displayed. Additional key presses will produce other characters on that key. See the chart below.
– Press CID/-VOLUME or DIR /VOLUME+ to move the cursor to the left or right.
– Press
Dial
Key
1
2
3
4
5
6
7
8
9
0
1
1
A
D
G
J
M
P
T
W
0
#
space
2
#
B
E
H
K
N
Q
U
X
?
DIRECTORY
Pat Williams
555-1234
MUTE/DELETE
to erase letters.
Characters by number of key presses
3
4
5
6
7
‘
,
.
&
C
2
a
b
c
3
d
e
f
F
I
4
g
h
i
L
5
j
k
l
O
6
m
n
o
R
S
7
p
q
V
8
t
u
v
Y
Z
9
w
x
!
/
(
)
8
9
r
s
y
z
@
8.Press MENU/SELECT to store your new directory entry. The name and the telephone number
will then be shown on the screen. To change it
later, see page 30.
9. Press OFF/CLEAR to return to the DIRECTORY
menu. Press and hold OFF/CLEAR to return to
the idle mode.
27
Telephone operation
Directory search
To cancel an operation, back up to the previous
menu, or exit the menu display press OFF/CLEAR.
To return to the idle mode press and hold
OFF/CLEAR.
To browse through the directory
DIRECTORY
Andrew
555-6789
1.Press DIR in idle mode to display the first listing in the directory. DIRECTORY EMPTY will be
displayed if there are no directory entries.
-OR-
DIRECTORY
Barbara
555-9876
You can also display the first listing in the
directory by first pressing MENU/SELECT, then
MENU /SELECT to choose DIRECTORY, then
press MENU/SELECT again to choose REVIEW.
2.Press CID/-VOLUME or DIR /VOLUME+ to browse
through the directory. Entries will be displayed
alphabetically by the first letter in the name.
28
Telephone operation
Directory search
To cancel an operation, back up to the previous
menu, or exit the menu display press OFF/CLEAR.
To return to the idle mode press and hold
OFF/CLEAR.
To search by name
1.Press DIR in idle mode to display the first listing in the directory. DIRECTORY EMPTY will be
displayed if there are no directory entries.
2.When a name entry is displayed, press a dial
pad keys (2-9) to start a quick name search.
The directory will display the first name begin-
ning with the first letter associated with the
dial pad key, if there is an entry in the directory
that begins with that letter.
3.To see other names that start with the letters
on the dial pad key, keep pressing the key. The
names will be shown in alphabetical order.
For example, if you have name entries Jennifer,
Jessie, Kevin and Linda in your directory:
• If you press 5 (JKL) once, you will see Jennifer.
• If you press 5 (JKL) twice, you will see Jessie.
• If you press 5 (JKL) three times, you will see
Kevin.
• If you press 5 (JKL) four times, you will see
Linda.
• If you press 5 (JKL) five times, you will see
Jennifer again.
NOTES:
1. If there is no name entry matching the first letter of the
key you press, you will see a name entry that matches the
next letter of the key.
2. If you press a key (2-9) and there is no name entry to
match those letters, the directory will show the entry that
matches the next available letter in the directory.
29
Telephone operation
To dial, delete or change entries
To dial, delete or change a directory entry (name and
number), the entry must be displayed on the handset. Use directory search (pages 28-29) to display an
entry. To exit the directory press OFF/CLEAR.
To dial a displayed number
When a directory entry is displayed, press
PHONE/FLASH or SPEAKER to dial the displayed
number.
To delete an entry
When a directory entry is displayed, press
MUTE/DELETE to delete the displayed entry from the
directory. Once deleted, an entry cannot be retrieved.
To change an entry
When a directory entry is displayed:
DIRECTORY
Andrew
555-6789
DIRECTORY
EDIT NUMBER
555-1234
DIRECTORY
EDIT NAME
Andy
DIRECTORY
Andy
555-1234
1. Press MENU/SELECT to modify the entry. You will
be prompted to EDIT NUMBER.
• Press the dial pad keys to add digits.
• Press MUTE/DELETE to erase digits.
• Press CID/-VOLUME or DIR
the cursor.
/VOLUME+ to
move • Press and hold REDIAL/PAUSE to add a three-
second pause if desired.
• Press REDIAL/PAUSE, then CID/-VOLUME or
DIR /VOLUME+ to scroll to a previously dialed number. Press MENU/SELECT to add the redial number to the entry.
2. Press MENU/SELECT. ��������������������������
You will be prompted to EDIT NAME.
• Press the dial pad keys to add characters (page 27).
• Press MUTE/DELETE to erase characters.
• Press� CID/-VOLUME or DIR /VOLUME+ to move the cursor.
3. Press MENU/SELECT to confirm.
4. Press OFF/CLEAR to return to the DIRECTORY
menu. Press and hold OFF/CLEAR to return to
the idle mode.
30
Caller ID operation
Caller ID operation
Information about caller ID with call waiting
CHRISTINE SMITH
908-555-0100
NOV23 10:01AM
TONE
MUTE
REDIAL
DELETE
PAUSE
This product has a caller ID function with call
waiting feature which works with service from
your local telephone company.
Caller ID with call waiting lets you see the name
and telephone number of the caller before
answering the telephone, even while on another
call.
It may be necessary to change your telephone
service to use this feature. Contact your
telephone company if:
• You have both caller ID and call waiting, but
as separate services (you may need combined
service).
• You have only caller ID service, or only call
waiting service.
• You do not have any caller ID or call waiting
services.
This product can be used with regular caller ID service,
or this product’s other features can be used without
subscribing to either caller ID or combined caller ID
with call waiting service.
There are fees for caller ID services. In addition,
services may not be available in all areas.
Depending on your service, the caller’s number, or
the caller’s name and number may be displayed. This
product can provide information only if both you and
the caller are in areas offering caller ID service and if
both telephone companies use compatible equipment.
The time and date are sent by the telephone company
along with the call information.
31
Caller ID operation
Caller ID operation
Shared caller ID log
CHRISTINE SMITH
908-555-0100
NOV23 �����������
10:01AM
The caller ID log is stored in the telephone base,
and is shared by all handsets. Changes made on
any handset will apply to all.
NOTE: Only one handset can review the directory or call-
er ID log at a time. If the other handset attempts to enter the call log, its screen will display NOT AVAILABLE AT THIS TIME.
How caller ID works
TONE
MUTE
REDIAL
DELETE
PAUSE
If you subscribe to caller ID service provided by
your local telephone company, information about
each caller will be displayed between the first and
second ring.
Caller’s name
Caller’s number
CALL LOGNEW
CHRISTINE SMITH
908-555-0100
NOV 23 10:01AM
Appears when
the call is missed
and un-reviewed.
Time of call
Date of call
Information about the last 50 incoming calls is
stored in the call log. You can review the call log
to find out who has called and return the call or
save the caller’s name and number into the directory.
When the call log is full, the oldest entry is deleted to make room for new incoming call information.
If a call is answered before the information
appears on the screen, it will not be saved in the
call log.
NOTE: Caller ID features will work only if both you and the caller are in areas offering caller ID service, and if both tele-
phone companies use compatible equipment.
32
Caller ID operation
Caller ID operation
Memory match
Chris
908-555-0100
NOV23 10:01AM
Names of callers will be displayed only if the information is provided by your local telephone company.
If the telephone number of the caller exactly matches a telephone number in your directory, the name
that appears on the screen will match the corresponding name already in the directory.
TONE
MUTE
REDIAL
DELETE
PAUSE
Example: If Christine Smith calls, her name will
appear as Chris if this is how it was entered in the
directory.
NOTE: The number shown in your caller ID will be in the format sent by the telephone company. The tele-
phone company usually delivers ten-digit telephone numbers (area code plus telephone number). If the
telephone number of the person calling does not
exactly match a number in your directory, the name will appear as delivered by the telephone company. For example if the telephone company includes the area code and the directory number does not, the name will appear as delivered by the telephone company.
HANDSET 1
4 MISSED CALLS
10:01AM
Missed calls
When a handset is in idle mode with un-reviewed
calls, its screen will show XX MISSED CALLS.
Un-reviewed entries will be counted as missed
calls when the telephone is idle. Each time a call
log entry marked NEW is reviewed, the number of
missed calls decreases by one.
If there are too many missed calls and you
don’t want to un-reviewed them one by one
but still want to keep them in the caller ID log,
press and hold
OFF/ CLEAR for four seconds
when the handset is idle. All reviewed entries in
the caller ID log will be considered old and the
counter is reset to 0.
33
Caller ID operation
HANDSET 1
4 MISSED CALLS
4:30 PM
CALL LOGNEW
Pat Williams
555-1234
NOV 23 10:31AM
CALL LOGNEW
Jeffrey Adams
555-9876
NOV 23 10:21AM
CALL LOGNEW
Chris Thompson
908-555-0100
NOV 23 10:11AM
- OR CALL LOGNEW
Chris Thompson
1-908-555-0100
NOV 23 10:11AM
CALL LOGNEW
Chris Thompson
1-555-0100
NOV 23 10:11AM
CALL LOGNEW
Chris Thompson
555-0100
NOV 23 10:11AM
To review the call log
To review the call log
Press CID/-VOLUME to review the call log. The call
log displays the caller ID entries in reverse chronological order. The most recent call is displayed
first. Press CID/-VOLUME or DIR /VOLUME+ to scroll
through the list as shown at left. Press OFF/CLEAR to
return to the idle screen.
NOTE: You can also display the caller ID entries in the call log, when handset is idle, press MENU/SELECT, then CID/-VOLUME to choose CALL LOG, and then press MENU/SELECT.
To return a call
Press PHONE/FLASH or SPEAKER to call the displayed
number.
Caller ID numbers may appear with an area code
that may not be required for local calls, or without a
1 that may be needed for long distance calls. If the
number displayed is not in the correct format, you
can change how it is dialed.
To change the number before dialing, press # repeatedly to see different dialing options (you can choose
to dial with or without an area code, and with or
without the 1), then press PHONE/FLASH or SPEAKER
to dial the number.
Other options while reviewing the call log
• Press MUTE/DELETE to delete the current entry from
the call log.
• Press and hold MUTE/DELETE to delete all entries
from the call log. When asked to confirm, press
MENU/SELECT to delete all entries, or press
OFF/CLEAR
to exit without deleting any entries.
• Press MENU/SELECT to copy this entry into the directory.
If the name or number is not provided, you will be
prompted to enter them (page 27).
• Press and hold OFF/CLEAR to return to the idle
screen.
NOTE: If neither the name nor number are not provided, UNABLE TO SAVE will be displayed.
34
Appendix
Screen icons, indicator lights & tones
Screen icons & alert tones
Screen icons
Battery charging (animated display).
HANDSET 1
Low battery (flashing); place handset in telephone
base to recharge.
MUTE
NEW
10:01AM
Speakerphone is in use.
11/23
New voicemail messages are received.
Ringer off.
MUTE
Microphone is muted.
NEW
Missed and un-reviewed calls.
Handset alert tones
Two short beeps
The volume level is at the maximum or minimum setting.
Four short beeps
Low battery warning.
Two beeps
Out of range from the telephone base while on a call.
Confirmation tone
Command completed successfully.
Indicator lights
CHARGE/IN USE
• On when the cordless handset is properly positioned to charge in the telephone base.
• Flashes during an incoming call’s ringing.
• Flashes when the handset is in use, or when another telephone is in use on the same line.
VOICEMAIL
Flashes when there are new voicemail
(requires voicemail service from your local
telephone company).
TONE
SPEAKER
On when speakerphone is in use.
35
MUTE
REDIAL
DELETE
PAUSE
Appendix
Handset display screen messages
Screen display messages
XX MISSED CALLS
There are new calls in the caller ID log.
ALREADY SAVED
The telephone number you have
entered is already stored in the directory.
CALL LOG EMPTY
You are accessing an empty call log.
CALLING
OTHER HANDSET
You have placed an intercom call to the
other handset.
CALL TRANSFERRED
An external call is transferred to the
destination handset.
CHARGING
A handset with a low battery has been
placed to charge in the telephone base
or charger.
CONNECTING ...
The handset has lost connection with
the telephone base.
DIRECTORY EMPTY
You are accessing an empty directory.
ENDED
You have just disconnected a call.
OTHER HANDSET
IS CALLING
The other handset is calling.
TONE
MUTE
REDIAL
DELETE
PAUSE
INCOMING
CALL
There is an incoming call.
INTERCOM
The handset is in an intercom call.
INTERCOM ENDED
The intercom call has just been ended by
the person on either handset.
LINE IN USE
The other handset or another telephone on the same line is in use.
LIST FULL
You are attempting to save to a full
directory.
LOW BATTERY
The battery needs to be recharged.
MICROPHONE ON
MUTE has been turned off and the person
on the other end can hear you.
36
Appendix
Handset display screen messages
Screen display messages
MICROPHONE MUTED The handset microphone is now muted.
NEW VOICE MAIL
There are new voicemail messages.
NO LINE
There is no telephone line connected.
NOT AVAILABLE
AT THIS TIME
Someone else is already using the directory
or call log which you are trying to access.
NO SIGNAL,
CALL ENDED
During a call, the handset is no longer
connected with the telephone base. Try
moving it closer to the telephone base.
** PAGING **
The telephone base is paging both handsets.
PHONE
The handset is in use.
PLACE
IN CHARGER
Battery power is very low. Place the handset in the telephone base or charger to
recharge.
SPEAKER
The handset speakerphone is in use.
SAVED
The call log entry was saved to the directory
successfully.
NOT AVAILABLE
Failed intercom call.
TONE
MUTE
REDIAL
DELETE
PAUSE
WARNING
CHECK BATTERY!
The battery is not installed or not installed
properly in the handset.
-OR-
The battery needs to be replaced.
-OR-
An incorrect battery has been installed by
mistake. Use only the supplied rechargeable battery or replacement battery (model
27910, part number 89-0099-00-00) or
equivalent. To order a replacement battery,
visit our website at www.telephones.att.com
or call 1 (800) 222-3111. In Canada dial 1
(866) 288-4268.
37
Appendix
Troubleshooting
If you have difficulty with your telephone, please try the suggestions below. For
Customer Service, visit our website at www.telephones.att.com or call 1 (800) 222-3111.
In Canada dial 1 (866) 288-4268.
My telephone
does not work
at all.
• Make sure the battery is installed and charged correctly
(page 7). For optimum daily performance, return the cordless handset to the telephone base after use.
• Make sure the power adapter is securely plugged into an
outlet not controlled by a wall switch.
• Make sure the telephone line cord is plugged firmly into the
telephone base and the modular wall jack.
• Unplug the telephone’s electrical power. Wait for approximately 15 seconds, then plug it back in. Allow up to one
minute for the cordless handset and base to synchronize.
• Charge the battery in the cordless handset for at least 16
hours.
• Remove and re-insert the battery. If that still does not work,
it may be necessary to purchase a new battery. Please refer
to the Battery installation & charging section of this user's
manual (page 7).
• Disconnect the telephone base from the telephone line wall
jack and plug in a working telephone. If this telephone does
not work, the problem is probably in the wiring or the local
service. Call the local telephone company.
There is no dial
tone.
•��������������������������������������
First, try all the above suggestions.
•������������������������������������������������������������
Move the cordless handset closer to the telephone base. It
might be out of range.
•��������������������������������������������������������������
The telephone line cord might be malfunctioning. Try installing a new telephone line cord.
•�����������������������������������������������������������
Disconnect the telephone base from the telephone jack and
connect a different telephone. If there is no dial tone on the
telephone either, the problem is in your wiring or local service. Contact your local telephone company.
38
Appendix
Troubleshooting
I cannot dial out. • First, try all the above suggestions.
• Make sure there is a dial tone before dialing. It is normal if
the cordless handset takes a second or two to synchronize
with the telephone before producing a dial tone. Wait an
extra second before dialing.
• Check that all the telephones connected to the same
telephone line are hung up.
• Makes sure the telephone is set to the correct dial mode
(pulse dial or tone dial) for the service in your area. Refer
to the Handset settings section of this user’s manual (page
18) to set the dial mode.
• If the other telephones in your home are having the same
problem, the problem is in the wiring or local service.
Contact your local telephone company (charges may apply).
• Eliminate any background noise. Noise from a television,
radio, or other appliances may cause the telephone to not
dial out properly. If you cannot eliminate the background
noise, first try muting the cordless handset before dialing,
or dialing from another room in your home with less background noise.
LOW BATTERY
is displayed on
screen.
• Place the handset in the base or charger for recharging.
• Remove and re-install the battery and use it normally until
fully discharged, then recharge the handset on the telephone base or charger for 16 hours.
• If the above measures do not correct the problem, the battery may need to be replaced.
The battery does • Make sure the handset is placed in the telephone base or
charger correctly. The CHARGE light on the telephone base
not charge in the
or charger should be on.
handset or the
handset battery • If the cordless handset is in the charger or in the telephone
does not accept
base but the CHARGE light is not on, refer to The CHARGE
charge.
light is off in this section (page 40).
39
Appendix
Troubleshooting
• It may be necessary to purchase a new battery. Please refer
to the Battery installation & charging section of this user's
manual (page 7).
• The telephone might be malfunctioning. Please refer to the
Limited warranty section of this user’s manual (page 51)
for further instruction.
The CHARGE
light is off.
• Clean the metallic charging contacts on the cordless handsets each month using a pencil eraser or a dry non-abrasive
fabric.
Metallic charging contacts
• Make sure the power adapter and telephone line cords are
plugged in correctly and securely.
• Unplug the power adapter. Wait for 15 seconds before
plugging it back in. Allow up to one minute for the cordless
handset and telephone base to reset.
• The telephone might be malfunctioning. Please refer to the
Limited warranty section of this user’s manual for further
instruction (page 51).
The telephone
does not ring
when there is an
incoming call.
•���������������������������������������
Make sure the ringer is on. (page 24).
•���������������������������������������������������������
Make sure the telephone line cord and power adapter are
plugged in properly (page 6).
•��������������������������������������������������������
The cordless handset may be too far from the telephone
base. Move it closer to the telephone base.
•��������������������������������������������������������
There may be too many extension telephones on the telephone line to allow all of them to ring simultaneously. Try
unplugging some of them.
•����������������������������������������������������������
If the other telephones in your home are having the same
problem, the problem is in the wiring or local service.
Contact the local telephone company (charges may apply).
40
Appendix
Troubleshooting
• Other electronic products can cause interference to your
cordless telephone. Try installing your telephone as far
away as possible from the following electronic devices:
wireless routers, radios, radio towers, pager towers, cellular
telephones, digital telephones, intercoms, room monitors,
televisions, VCRs, personal computers, kitchen appliances,
and other cordless telephones.
•���������������������������������������������������������
Test a working telephone at the same telephone jack. If
another telephone has the same problem, the problem is in
the telephone jack. Contact your local telephone company
(charges may apply).
•��������������������������������������������������������������
The telephone line cord might be malfunctioning. Try installing a new telephone line cord.
•��������������������������������������������������������������
Re-install the battery and place the cordless handset in the
telephone base.
•������������������������������������������������������������
Wait for the cordless handset to synchronize with the telephone base. Allow up to one minute for this to take place.
M y t e l e p h o n e • The cordless handset may be too far from the telephone
base. Move closer to the telephone base and try to answer
rings but when I
the call.
try to answer the
call the handset screen shows
CONNECTING…
CONNECTING...
displays on my
cordless handset.
Ensure that the telephone base is powered up.
• Place the cordless handset in the telephone base for one
minute to allow the cordless handset and telephone base to
resynchronize channels.
• Move the cordless handset closer to the telephone base. You
might have moved out of range.
• If the cordless handset is in its telephone base and the
CHARGE light does not come on, refer to The CHARGE light
is off section in this troubleshooting guide (page 40).
• Reset the telephone base. Unplug the telephone base’s electrical power. Wait for 15 seconds then plug it back in. Allow
up to one minute for the cordless handset and telephone
base to reset.
41
Appendix
Troubleshooting
• Other electronic products can cause interference with your
cordless telephone. Try installing your telephone as far away
from these types of electronic devices as possible. These
devices include: routers, radios, radio towers, pager towers,
cell phones, intercoms, room monitors, televisions, personal
computers, kitchen appliances and cordless telephones.
There is noise or
interference during a telephone
conversation.
• The handset may be out of range. Move it closer to the
telephone base.
My calls fade out
or cut in and out
when I am using
t h e c o rd l e s s
handset.
• Other electronic products can cause interference to your
cordless telephone. Try installing your telephone as far
away as possible from the following electronic devices:
wireless routers, radios, radio towers, pager towers, cellular
telephones, digital telephones, intercoms, room monitors,
televisions, VCRs, personal computers, kitchen appliances,
and other cordless telephones.
• If you have a headset plugged into the handset, try unplugging it and firmly plugging it in again.
• Microwave ovens operate on the same frequency as your
telephone. It is normal to experience static on your telephone while the microwave oven is operating. Do not install
this telephone in the same outlet or near a microwave
oven.
• If your telephone is plugged in with a modem or a surge
protector, plug the telephone (or modem/surge protector)
into a different location. If this solves the problem, re-locate
your telephone or modem farther apart from each other, or
use a different surge protector.
• The layout of your home or office might be limiting the
operating range. Try moving the base to another location,
preferably a higher location for better reception.
• Appliances or other cordless telephones plugged into the
same circuit as the telephone base can cause interference.
Try moving the appliance or telephone base to another outlet.
42
Appendix
Troubleshooting
• Disconnect the telephone base from the modular jack and
plug in a corded telephone. If calls are still not clear, the
problem is probably in the wiring or local service. Contact
your local service company (charges may apply).
• Other cordless telephones and 802.11 wireless routers that
are used for home computer networks both use internal
radios to communicate. The radios may interfere with one
another. You can improve the performance of your cordless
telephones and your router by:
a. Positioning your new telephone as far away from any
other already installed cordless telephone in your home
as possible. This will hinder the interference of the two
systems with one another.
b. Positioning your telephone base as far as possible from
your router, computer or any other computer devices.
c. Selecting channels 4 through 10 for your router (refer to
your router’s user manual for more information).
• Do you have DSL service? If yes, you need to have a DSL
filter installed at every telephone jack that has a telephone
connected to it. Contact your DSL service provider for filter
information
I hear other calls
when using the
telephone.
• D
isconnect the telephone base from the telephone jack.
Plug in a different telephone. If you still hear other calls,
the problem is probably in the wiring or local service. Call
your local telephone company.
My caller ID
features are not
working properly.
• Caller ID is a subscription service. You must subscribe to
this service from your local telephone company for this feature to work on your telephone.
• The caller may not be calling from an area which supports
caller ID.
• Both you and the caller’s telephone companies must use
equipment which are compatible with caller ID service.
• If you subscribe to DSL service, install a noise filter to
the telephone line between the telephone base and the
telephone line jack. Contact your DSL service provider
for filter information.
43
Appendix
Troubleshooting
The system does
not receive caller
ID or the system
does not display
caller ID during
call waiting.
• Make sure you subscribe to caller ID with call waiting features services provided by the local telephone company.
• The caller may not be calling from an area which supports
caller ID.
• Both you and the caller’s telephone companies must use
equipment which are compatible with caller ID service.
• If you subscribe to DSL service, install a noise filter to
the telephone line between the telephone base and the
telephone line jack. Contact your DSL service provider
for filter information.
Common cure
for electronic
equipment.
• If the telephone is not responding normally, try putting the
cordless handset in the telephone base or the charger. If it
does not seem to respond, try the following (in the order
listed):
1. Disconnect the power to the telephone base.
2. Disconnect the battery on the cordless handset.
3. Wait a few minutes before connecting power to the
telephone base.
4. Re-install the battery and place the cordless handset
into the telephone base or charger.
5. Wait for the cordless handset to synchronize its connection
with the telephone base. Allow up to one minute for this to
take place.
44
Appendix
Important safety instructions
This symbol is to alert you to important operating or servicing instructions that may
appear in this user’s manual. Always follow basic safety precautions when using this product to
reduce the risk of injury, fire, or electric shock.
Safety information
• Read and understand all instructions in the user’s manual. Observe all
markings on the product.
• Avoid using a telephone during a thunderstorm. There may be a slight
chance of electric shock from lightning.
• Do not use a telephone in the vicinity of a gas leak. If you suspect a gas
leak, report it immediately, but use a telephone away from the area where gas
is leaking. If this product is a cordless model, make sure the base is also away
from the area.
• Do not use this product near water, or when you are wet. For example, do
not use it in a wet basement or shower, or next to a swimming pool, bathtub,
kitchen sink, or laundry tub. Do not use liquids or aerosol sprays for cleaning. If
the product comes in contact with any liquids, unplug any line or power cord
immediately. Do not plug the product back in until it has dried thoroughly.
• Install this product in a protected location where no one can trip over any
line or power cords. Protect cords from damage or abrasion.
• If this product does not operate normally, read Troubleshooting in this
user’s manual. If you cannot solve the problem, or if the product is damaged,
refer to the limited warranty. Do not open this product except as may be directed in your user’s manual. Opening the product or reassembling it incorrectly
may expose you to hazardous voltages or other risks.
• If this product has user-replaceable batteries, replace batteries only as
described in your user’s manual. Do not burn or puncture batteries — they
contain caustic chemicals.
• If this product has a three-prong (grounding) plug or a polarized plug with
one wide prong, it may not fit in non-polarized outlets. Do not defeat the
purpose of these plugs. If they do not fit in your outlet, the outlet should be
replaced by an electrician.
CAUTION: Use only the power adapter provided with this product. To obtain a replacement, visit our website at www.telephones.att.com or call 1(800) 222–3111. In Canada dial
1 (866) 288-4268.
45
Appendix
Important safety instructions
Especially about cordless telephones
• Privacy: The same features that make a cordless phone convenient create
some limitations. Telephone calls are transmitted between the base and the
handset by radio waves, so there is a possibility that your cordless phone conversations could be intercepted by radio receiving equipment within range of
the cordless handset. For this reason, you should not think of cordless phone
conversations as being as private as those on corded phones.
• Electrical power: The telephone base of this cordless telephone must be
connected to a working electrical outlet. The electrical outlet should not
be controlled by a wall switch. Calls cannot be made from the handset
if the telephone base is unplugged or switched off, or if the electrical
power is interrupted.
• Power adapter: The power adapter is intended to be correctly oriented in a
vertical or floor mount position. The prongs are not designed to hold the plug
in place if it is plugged into a ceiling or an under-the-table/cabinet outlet.
• Potential TV interference: Some cordless telephones operate at frequencies
that may cause interference to TVs and VCRs. To minimize or prevent such
interference, do not place the telephone base of the cordless telephone near
or on top of a TV or VCR. If interference is experienced, moving the cordless
telephone farther away from the TV or VCR will often reduce or eliminate the
interference.
• Rechargeable batteries: This product contains either nickel-cadmium or nickelmetal hydride rechargeable batteries. Exercise care in handling batteries in
order not to short the battery with conducting material such as rings, bracelets,
and keys. The battery or conductor may overheat and cause harm. Observe
proper polarity between the battery and the battery charger.
• Nickel-cadmium rechargeable batteries: Must be recycled or disposed of
properly. Do not dispose of in household garbage. Do not burn or puncture. Like
other batteries of this type, if burned or punctured, they could release caustic
material which could cause injury.
The RBRC™ Seal means that the manufacturer is voluntarily participating in an industry program to collect and recycle nickel-cadmium rechargeable batteries when taken out of
service within the United States. These batteries may be taken to a participating local retailer of
replacement batteries or recycling center. Or you may call 1-800-8-BATTERY for locations accepting spent nickel-cadmium Batteries.
46
Appendix
Important safety instructions
• Nickel-metal hydride rechargeable batteries: Dispose of these batteries
in a safe manner. Do not burn or puncture. Like other batteries of this type,
if burned or punctured, they could release caustic material which could
cause injury.
The RBRC™ Seal means that the manufacturer is voluntarily participating in an industry program to collect and recycle nickel-metal hydride rechargeable batteries when taken out of
service within the United States. These batteries may be taken to a participating local retailer of
replacement batteries or recycling center. Or you may call 1-800-8-BATTERY for locations accepting spent nickel-metal hydride Batteries.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless telephones):
Wireless Technology Research, LLC (WTR), an independent research entity, led
a multidisciplinary evaluation of the interference between portable wireless
telephones and implanted cardiac pacemakers. Supported by the U.S. Food
and Drug Administration, WTR had recommended to physicians that:
Pacemaker patients
•Should keep wireless phones at least six inches from the pacemaker.
•Should NOT place wireless phones directly over the pacemaker, such as in a
breast pocket, when it is turned ON.
•Should use the wireless phone at the ear opposite the pacemaker.
WTR’s evaluation did not identify any risk to bystanders with pacemakers from
other persons using wireless phones.
Especially about telephones answering systems
Two-way recording: This unit does not sound warning beeps to let the other
party know that the call is being recorded. To ensure that you are in compliance with any federal or state regulations regarding recording a telephone
call, you should start the recording process and then inform the other party
that you are recording the call.
SAVE THESE INSTRUCTIONS
47
Appendix
FCC Part 68 & ACTA
This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative Council for Terminal Attachments (ACTA).
The label on the back or bottom of this equipment contains, among other things,
a product identifier in the format US: AAAEQ##TXXXX. This identifier must be provided to your local telephone company upon request.
The plug and jack used to connect this equipment to premises wiring and the
telephone network must comply with applicable Part 68 rules and technical
requirements adopted by ACTA. A compliant telephone cord and modular
plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. An RJ11 jack should normally
be used for connecting to a single line and an RJ14 jack for two lines. See
Installation Instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to determine how many devices you
may connect to your telephone line and still have them ring when you are called.
The REN for this product is encoded as the 6th and 7th characters following the
US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all
areas, the sum of all RENs should be five (5.0) or less. For more information, please
contact your local telephone company.
This equipment may not be used with Party Lines. If you have specially wired
alarm dialing equipment connected to your telephone line, ensure the connection
of this equipment does not disable your alarm equipment. If you have questions
about what will disable alarm equipment, consult your telephone company or a
qualified installer.
If this equipment is malfunctioning, it must be unplugged from the modular jack
until the problem has been corrected. Repairs to this telephone equipment can
only be made by the manufacturer or its authorized agents. For repair procedures,
follow the instructions outlined under the Limited Warranty.
If this equipment is causing harm to the telephone network, the telephone company may temporarily discontinue your telephone service. The telephone company
is required to notify you before interrupting service. If advance notice is not practical, you will be notified as soon as possible. You will be given the opportunity to
correct the problem and the telephone company is required to inform you of your
right to file a complaint with the FCC. Your telephone company may make changes in its facilities, equipment, operation, or procedures that could affect the proper
functioning of this product. The telephone company is required to notify you if
such changes are planned.
48
Appendix
FCC Part 68 & ACTA
If this product is equipped with a corded or cordless handset, it is hearing aid
compatible.
If this product has memory dialing locations, you may choose to store emergency telephone numbers (e.g., police, fire, medical) in these locations. If you
do store or test emergency numbers, please:
• Remain on the line and briefly explain the reason for the call before hanging up.
• Perform such activities in off-peak hours, such as early morning or late
evening.
49
Appendix
FCC Part 15
This equipment has been tested and found to comply with the requirements for a
Class B digital device under Part 15 of the Federal Communications Commission
(FCC) rules.
These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
To ensure safety of users, the FCC has established criteria for the amount of radio
frequency energy that can be safely absorbed by a user or bystander according
to the intended usage of the product. This product has been tested and found to
comply with the FCC criteria. The handset may be safely held against the ear of
the user. The telephone base shall be installed and used such that parts of the
user’s body other than the hands are maintained at a distance of approximately 20
cm (8 inches) or more. If you choose to use a clipping device, please make sure to
only use the supplied AT&T belt clip.
50
Appendix
Limited warranty
The AT&T brand is used under license - any repair, replacement or warranty
service, and all questions about this product should be directed to: In the
United States of America call 1(800) 222-3111 or visit www.telephones.att.
com. In Canada dial 1 (866) 288-4268.
1. What does this limited warranty cover?
The manufacturer of this AT&T-branded product warrants to the holder of a valid proof of purchase (“CONSUMER” or “you”) that the product and all accessories provided in the sales package (“PRODUCT”) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the PRODUCT operating instructions. This limited warranty extends only to the CONSUMER for products purchased and used in the United States of America and Canada.
2. What will be done if the PRODUCT is not free from defects in materials and workmanship during the limited warranty period (“materially defective PRODUCT”)?
During the limited warranty period, the manufacturer’s authorized service representative will repair or replace at the manufacturer’s option, without charge, a materially defective PRODUCT. If the manufacturer repairs the PRODUCT, they may use new or refurbished replacement parts. If the manufacturer chooses to replace the PRODUCT, they may replace it with a new or refurbished PRODUCT of the same or similar design. The
manufacturer will retain defective parts, modules, or equipment. Repair or replacement of the PRODUCT, at the manufacturer’s option, is your exclusive remedy. The manufacturer will return repaired or replacement products to you in working condition. You should expect the repair or replacement to take approximately 30 days.
3. How long is the limited warranty period?
The limited warranty period for the PRODUCT extends for ONE (1) YEAR from the date of purchase. If the manufacturer repairs or replaces a
materially defective PRODUCT under the terms of this limited warranty, this limited warranty also applies to repaired or replacement PRODUCT for a period of either (a) 90 days from the date the repaired or replacement
PRODUCT is shipped to you or (b) the time remaining on the original one-
year limited warranty; whichever is longer.
51
Appendix
Limited warranty
4. What is not covered by this limited warranty?
This limited warranty does not cover:
• PRODUCT that has been subjected to misuse, accident, shipping or other
physical damage, improper installation, abnormal operation or handling,
neglect, inundation, fire, water, or other liquid intrusion; or
• PRODUCT that has been damaged due to repair, alteration, or modification
by anyone other than an authorized service representative of the manufacturer; or
• PRODUCT to the extent that the problem experienced is caused by signal
conditions, network reliability or cable or antenna systems; or
• PRODUCT to the extent that the problem is caused by use with non-AT&T
accessories; or
• PRODUCT whose warranty/quality stickers, PRODUCT serial number plates
or electronic serial numbers have been removed, altered or rendered illegible; or
• PRODUCT purchased, used, serviced, or shipped for repair from outside the
United States of America or Canada, or used for commercial or institutional
purposes (including but not limited to products used for rental purposes); or
• PRODUCT returned without valid proof of purchase (see item 6 below); or
• Charges for installation or setup, adjustment of customer controls, and installation or repair of systems outside the unit.
5. How do you get warranty service?
To obtain warranty service in the United States of America, call 1 (800) 222-3111.
In Canada, please dial 1 (866) 288-4268. NOTE: Before calling for service,
please review the user’s manual - a check of the PRODUCT controls and features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage
during transit and transportation and are responsible for delivery or handling
charges incurred in the transport of the PRODUCT(s) to the service location.
The manufacturer will return repaired or replaced PRODUCT under this limited
warranty to you, transportation, delivery or handling charges prepaid. The manufacturer assumes no risk for damage or loss of the PRODUCT in transit. If the
PRODUCT failure is not covered by this limited warranty, or proof of purchase
does not meet the terms of this limited warranty, the manufacturer will notify
you and will request that you authorize the cost of repair prior to any further
repair activity. You must pay for the cost of repair and return shipping costs for
the repair of products that are not covered by this limited warranty.
52
Appendix
Limited warranty
6. What must you return with the PRODUCT to get warranty service?
You must:
a. Return the entire original package and contents including the PRODUCT
to the service location along with a description of the malfunction or difficulty; and
b. Include “valid proof of purchase” (sales receipt) identifying the PRODUCT
purchased (PRODUCT model) and the date of purchase or receipt; and
c. Provide your name, complete and correct mailing address, and telephone
number.
7. Other limitations
This warranty is the complete and exclusive agreement between you and
the manufacturer of this AT&T branded PRODUCT. It supersedes all other
written or oral communications related to this PRODUCT. The manufacturer
provides no other warranties for this PRODUCT. The warranty exclusively
describes all of the manufacturer’s responsibilities regarding the PRODUCT.
There are no other express warranties. No one is authorized to make modifications to this limited warranty and you should not rely on any such modification.
State/Provincial Law Rights: This warranty gives you specific legal rights,
and you may also have other rights which vary from state to state or province to province.
Limitations: Implied warranties, including those of fitness for a particular
purpose and merchantability (an unwritten warranty that the PRODUCT is
fit for ordinary use) are limited to one year from date of purchase. Some
states/provinces do not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to you. In no event shall the
manufacturer be liable for any indirect, special, incidental, consequential, or
similar damages (including, but not limited to lost profits or revenue, inability to use the PRODUCT or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this
PRODUCT. Some states/provinces do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase.
53
Appendix
Technical specifications
RF frequency band
(handset to base)
2400 MHz — 2483.5 MHz
RF frequency band
(base to handset)
2400 MHz -- 2483.5 MHz
Channels
95
Operating temperature
32°F — 122°F
0°C — 50°C
Telephone base voltage
(AC adapter input)
AC117V 60Hz
Telephone base��������
voltage
(AC adapter output)
DC9V 400mA
Handset voltage
3.6V 600mAh Ni-MH battery
Charger voltage
(AC adapter output)
DC9V 150mA
Telephone operating range
This cordless telephone operates with the maximum power allowed by the
Federal Communications Commission (FCC). Even so, the handset(s) and telephone base can communicate over only a certain distance - which can vary
with the locations of the telephone base and handset(s), the weather, the layout, and the construction of your home or office.
54
Appendix
Index
A
Alert tones, 35
Answering calls, 11
H
Hands-free use, 11
Handset locator, 13
Headset, 10
B
Battery charging, 7
Battery installation, 7
Belt clip, 10
Brightness, 23
I
Important safety instructions, 45
Intercom, 16
Intercom call transfer, 17
Incoming call log, 31
Incoming calls answering, 11
Indicator lights, 35
C
Call log, 31
Call transfer, 17
Call waiting, 14
Caller ID, 31-34
Clear voice mail indication, 20
Contrast, 22
K
Key tone, 21
L
Language, 18
Last number redial, 12
Low battery, 7
D
Delete call log entries, 34
Delete redial entries, 12
Dial Type, 18
Dialing,
from a CID record, 34
directory dialing, 30
Directory, 25
delete entries, 30
dial number, 30
edit entries, 30
name search, 29
new entries, 26
DSL filter, 6
M
Making calls, 11
Menus, 18
Multiple Handset use, 14
Mute, 15
N
Names,
enter into directory, 27
search for, 29
E
Elapsed time, 11
Ending calls, 11
O
Operating range, 54
F
FCC and ACTA, 48
55
Appendix
Index
P
Part checklist, 4
Predial, 11
Power adapter, 6
Q
Quick reference guide, 2-3
R
Receiving calls, 11
Recharging, 7
Redial, 12
Ring silencing, 12
Ringer melody, 21
Ringer volume, 24
S
Screen display messages, 36
Screen icons, 35
Search for names, 29
Speakerphone, 11
T
Tabletop mounting, 9
Technical specifications, 54
Telephone base installation, 5-6
Temporary ring silencing, 12
Temporay tone dialing, 15
Troubleshooting, 38
V
Volume control, 14
W
Wall mounting, 8
Wallpaper, 22
Warranty, 51
56
www.telephones.att.com
© 2007 Advanced American Telephones. All rights reserved.
AT&T and the AT&T logo are trademarks of AT&T Knowledge Ventures,
licensed to Advanced American Telephones. Printed in China. Issue 3 AT&T 04/07.
91-001100-020-100
Download PDF