Schneider Electric Wiser Micro Module Blind User Guide

Wiser Micro Module Blind
Device user guide
Information about features and functionality of the device.
05/2023
www.pdl.co.nz
Legal Information
The Schneider Electric brand and any trademarks of Schneider Electric SE and its
subsidiaries referred to in this guide are the property of Schneider Electric SE or its
subsidiaries. All other brands may be trademarks of their respective owners.
This guide and its content are protected under applicable copyright laws and
furnished for informational use only. No part of this guide may be reproduced or
transmitted in any form or by any means (electronic, mechanical, photocopying,
recording, or otherwise), for any purpose, without the prior written permission of
Schneider Electric.
Schneider Electric does not grant any right or license for commercial use of the guide
or its content, except for a non-exclusive and personal license to consult it on an "as
is" basis. Schneider Electric products and equipment should be installed, operated,
serviced, and maintained only by qualified personnel.
As standards, specifications, and designs change from time to time, information
contained in this guide may be subject to change without notice.
To the extent permitted by applicable law, no responsibility or liability is assumed by
Schneider Electric and its subsidiaries for any errors or omissions in the informational
content of this material or consequences arising out of or resulting from the use of the
information contained herein.
Table of Contents
Safety information .......................................................................................4
Wiser Micro Module Blind ..........................................................................5
For your safety ...........................................................................................5
About the device.........................................................................................6
Installing the device ....................................................................................6
Testing the device.......................................................................................7
Pairing the device .......................................................................................7
Pairing device manually.........................................................................8
Pairing device with auto scan...............................................................10
Configuring the device .............................................................................. 11
Changing the device icon .................................................................... 11
Renaming the device ..........................................................................12
Changing the device location ...............................................................12
Calibration..........................................................................................13
Removing the device ................................................................................16
Resetting the device .................................................................................16
Using the device.......................................................................................17
Manual operation ................................................................................17
Opening/Closing the shutter using app .................................................17
Setting up a schedule..........................................................................18
Creating a moment .............................................................................19
Creating an automation .......................................................................21
LED indication ..........................................................................................27
Troubleshooting .......................................................................................27
Technical data ..........................................................................................28
Compliance..............................................................................................29
Compliance information for Green Premium products ............................29
Trademarks ........................................................................................29
DUG_Wiser Micro Module Blind_PDL-00
3
Safety information
Safety information
Important information
Read these instructions carefully and look at the equipment to become familiar
with the device before trying to install, operate, service, or maintain it. The
following special messages may appear throughout this manual or on the
equipment to warn of potential hazards or to call attention to information that
clarifies or simplifies a procedure.
The addition of either symbol to a “Danger” or “Warning” safety label indicates
that an electrical hazard exists which will result in personal injury if the
instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that accompany this symbol to avoid possible
injury or death.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in
death or serious injury.
Failure to follow these instructions will result in death or serious injury.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result
in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to physical injury.
4
DUG_Wiser Micro Module Blind_PDL-00
Wiser Micro Module Blind
Wiser Micro Module Blind
PDL5015WBZ
For your safety
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
Safe electrical installation must be carried out only by skilled professionals.
Skilled professionals must prove profound knowledge in the following areas:
•
Connecting to installation networks.
•
Connecting several electrical devices.
•
Laying electric cables.
•
Safety standards, local wiring rules and regulations.
Failure to follow these instructions will result in death or serious injury.
DANGER
HAZARD OF ELECTRIC SHOCK
•
Make sure that the terminal connection area does not come in contact with
the metallic parts of any device installed in the same location.
•
Do not short the outputs to neutral.
•
The motor contacts and live conductor connection must be separated from
one another by a 240 VAC basic insulation.
Failure to follow these instructions will result in death or serious injury.
WARNING
HAZARD OF ELECTRIC SHOCK
•
Observe the regulations for working on live parts.
•
Only actuate the device buttons using insulated auxiliary equipment that
meets the requirements of EN 60900.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.
DUG_Wiser Micro Module Blind_PDL-00
5
Wiser Micro Module Blind
About the device
The Wiser Micro Module Blind (hereinafter referred to as module) combines the
advantages of smart shutter functionality with ordinary mechanical double pushbutton switches. It transforms a conventional switch into a connected device that
you can control from the switch or through the Wiser app.
Relay contacts are mechanically locked against each other to prevent
simultaneous triggering of the two relay outputs.
NOTE: Do not control any devices that depend on a permanent power supply.
Additional features:
•
Remote control with maximum of 10 mechanical double push-button
switches.
•
Protection of the motor against damage with two mutually mechanically and
electronically locked relay contacts.
•
Electronic overload protection, overheating protection and short-circuit
protection.
•
Setting a time schedule.
Installing the device
Refer to the installation instruction supplied with this product.
See Wiser Micro Module Blind.
6
DUG_Wiser Micro Module Blind_PDL-00
Wiser Micro Module Blind
Testing the device
Before using the module, manually test the module and make sure that it works
when connected to the shutter.
•
Short press the push button once, the shutter opens/closes gradually.
•
Press and hold the push button, the shutter opens/closes fully, record the time
it takes to fully open/close the shutter.
Pairing the device
Using the Wiser app, first pair your device with the Gateway/Hub to access and
control the device. You can either add the device manually or do an auto-scan to
pair it.
DUG_Wiser Micro Module Blind_PDL-00
7
Wiser Micro Module Blind
Pairing device manually
To pair the device manually:
1. On Home page, tap + .
2. Tap
and select the Wiser Hub
3. Select an option to add the device (A):
– Add Device with Install Code
– Add Device without Install Code
Add Device
Install Code is Recommended
To enhance network security, we strongly
recommend using the install code to add a
device.
If you are unable to scan or type the install
code, you can still add the device without it.
Add Device with Install Code
A
Add Device without Install Code
TIP: It is recommended to add the device with install code.
4. To pair the device with an install code, tap Add Device with Install Code to
display the slide-up menu. Select any one of the options (B):
– Scan Install Code: you can scan the device for the install code.
TIP: You can find the QR code on the rear side of the device.
– Enter Install Code Manually: you can manually enter the install code
from the device.
TIP: You can find the install code on the rear side of the device.
After scanning or entering the install code, proceed to Step 6.
Add Device
Install Code is Recommended
To enhance network security, we strongly
recommend using the install code to add a
device.
If you are unable to scan or type the install
code, you can still add the device without it.
Add Device with Install Code
Scanwithout
Install Code
Add Device
Install Code
Enter Install Code Manually
B
Cancel
5. To pair the device without install code, tap Add Device without Install Code.
8
DUG_Wiser Micro Module Blind_PDL-00
Wiser Micro Module Blind
6. Remove front panel from switch to access the device if you place the module
behind a mechanical push button.
7. Short press the push button 3 times.
The LED blinks orange.
NOTE: If the module is located behind the push button, the status LED is
not visible.
8. In the app, select Confirm LED is flashing orange and tap Start
Configuration (C).
Cancel
How to pair device
1. Remove front panel from switch.
1
2
L N 1 2
1
2
L N 1 2
3
C
9. After a few seconds, a solid green LED indicates that the device is
successfully paired to the Hub.
10. After the device is added in the app, tap Done.
DUG_Wiser Micro Module Blind_PDL-00
9
Wiser Micro Module Blind
Pairing device with auto scan
Pairing the device with auto scan automatically discovers the device when the
corresponding device is powered on.
To pair the device:
1. On the Home page, tap +.
2. Tap Auto scan tab and tap Confirm.
3. If you have multiple hubs, do Step 4 or proceed to Step 5.
4. Tap Select hub and select the Wiser hub from the slide-up menu.
5. Short press the setup/reset button 3 times (< 0,5 s) and wait for a few
seconds until the device search is complete.
The LED blinks orange.
TIP: If you want to pair multiple devices at once, perform step 5 on each
device and wait for a few seconds for them to be detected.
6. Tap Next (A) and select Micromodule Shutter.
Auto Scan
Micro
Next
A
7. Once the device is added successfully, tap Done.
10
DUG_Wiser Micro Module Blind_PDL-00
Wiser Micro Module Blind
Configuring the device
Changing the device icon
You can change the device icon using the Wiser app.
1. On the Home page, select the device for which you wish to change the icon.
2. At the top-right corner of the screen, tap
3. Tap edit
.
next to the device name.
4. Tap Icon to view the menu.
5. In the slide-up menu, select any one of the following (A) to change the device
icon:
– Take photo - allows you to take a photo with your device camera.
– Select from Icon Library - allows you to select an icon from the app
library.
– Select from Album - allows you to select a photo from the mobile gallery.
Icon
Name
Location
Take photo
Select from Icon Library
A
Select from album
Cancel
DUG_Wiser Micro Module Blind_PDL-00
11
Wiser Micro Module Blind
Renaming the device
You can rename the device using the Wiser app.
1. On the Home page, select the device for which you wish to rename.
2. At the top-right corner of the screen, tap
3. Tap edit
.
next to the device name.
4. Tap Name, enter the new name (A) and then tap Save.
Icon
Rename
Name
A
LocationCancel
Save
Changing the device location
You can change the device location using the Wiser app.
1. On the Home page, select the device for which you wish to change the
location.
2. At the top-right corner of the screen, tap
3. Tap edit
.
next to the device name.
4. Tap Location.
5. Select the desired location from the list (A) and then tap Save.
Device location
Save
Living Room
Master Bedroom
Kitchen
A
Dining Room
Study Room
Kids Room
12
DUG_Wiser Micro Module Blind_PDL-00
Wiser Micro Module Blind
Calibration
The shutter control is supplied in an uncalibrated state. Each shutter motors vary
in the speed at which they open and close (edge to edge). Therefore, the opening/
closing time of the shutter must be determined in the app.
NOTE:
•
Before using this device for the first time, it must be calibrated, or you can
adjust its duration manually.
•
Do not use the shutter either manually or on the app during calibration to
avoid interruption.
Shutter calibrating
To calibrate the run time manually:
1. On the device control panel page, tap Settings > Open/Close Duration.
2. On the slide-up menu, you can set the run time manually using +/- button or
using the sliding bar (A) and then tap Confirm.
NOTE: To determine the default run time, record the time it takes to fully
open/close the shutter (edge to edge).
Settings
6 Sec
90 Slat Rotation
B
120
0 Sec
45 Sec
90 Sec
Sec
A
180 Sec
Cancel
To calibrate the run time using app:
1. In Settings > Open/Close Duration, tap Calibration (B).
DUG_Wiser Micro Module Blind_PDL-00
13
Wiser Micro Module Blind
2. On the slide-up menu, select the calibration start point (C):
– Start From The Top: shutter will move from top to bottom (closing).
– Start From the Bottom: shutter will move from bottom to top (opening).
Settings
6 Sec
90 Slat Rotation
5 Sec
Start from the top
C
Cancel
3. Wait until the shutter reaches its starting point and then tap Start.
4. Tap Done (D) once the shutter reaches other end.
Settings
6 Sec
90 Slat Rotation
5 Sec
Done
00:10
Cancel
Done
D
The app displays the progress of calibration.
5. Once the process is complete, tap Tilt Calibration on the pop-up window for
shutter slat calibration.
14
DUG_Wiser Micro Module Blind_PDL-00
Wiser Micro Module Blind
Slat tilt angle calibration
To calibrate slat tilt angle:
1. On the setting page, tap Slat Tilt Angle for slide-up menu.
2. Select tilt type (A) based on the motor installed and then tap Confirm
90 Slat Rotation
180 Slat Rotation
Not Supported
Blind
Settings
6 Sec
90 Slat Rotation
of motor.
5 Sec
Tilt
0~90°
0~180°
90 Slat Rotation
180 Slat Rotation
A
Cancel
IMPORTANT: If the shutter is installed with a non rotating slat or blind, the
calibration process is complete, and no further steps to follow.
3. Read the pop-up notification and tap Confirm.
4. Make sure the shutter is in fully closed state and tap Prepare.
5. Select the check box (B) and tap Start.
Settings
6 Sec
90 Slat Rotation
5 Sec
B
to 90
00.00
C
Start
Reset
D
5 Sec
Cancel
Done
6. Tap Stop (C) to finish calibration.
TIP: You can retake the calibration by tapping Reset.
7. Tap Done once the process is complete.
The app displays the progress of calibration.
TIP: You can set the run time manually by taping
Duration Adjustment (D).
DUG_Wiser Micro Module Blind_PDL-00
15
Wiser Micro Module Blind
Removing the device
Using the Wiser app, you can remove a device from the device list.
To remove the device:
1. On the Home page, tap All devices > Micromodule Shutter.
2. Tap
to display more details.
3. Tap Remove and Factory Reset Device (A).
More
Micro Module Shutter
Others
A
TIP: On the Home page, tap and hold the Micromodule Shutter to
remove the device.
NOTE:
•
Removing the device will reset the module. After reset the LED turns
orange indicating that the module is ready to pair with another
network.
•
If there is a problem while pairing or resetting the module, refer to
Resetting the device, page 16.
Resetting the device
You can reset the device to factory default manually.
Short press the push button 3 times and then long press the push button once for
10 s.
After 10 s, LED starts blinking red then release the operation button.
NOTE: All configuration data, user data, and network data are deleted. After
which
•
No connectivity to other devices or rooms
•
No timer settings
The LED stops blinking upon successful reset of the device.
The module restarts and blinks green for a few seconds.
16
DUG_Wiser Micro Module Blind_PDL-00
Wiser Micro Module Blind
NOTE: After reset, the LED turns orange indicating that the device is ready for
pairing.
Using the device
Manual operation
When the module is connected to a mechanical double push-button switch, the
shutter can be controlled manually.
•
Short press the push button once, the shutter opens/closes gradually.
•
Press and hold the push button, the shutter opens/closes fully.
Opening/Closing the shutter using app
Using the Wiser app shutter can be controlled by following method.
Opening/Closing through home page
To open/close the shutter:
1. On the Home page, Tap All devices.
2. In Micromodule Shutter Tap on
DUG_Wiser Micro Module Blind_PDL-00
.
17
Wiser Micro Module Blind
3. On the slide up Control menu select Open/Close to operate the shutter.
My Home
Welcome Home
Home
Away
•••
All Devices
Control
Open
Close
Home
Opening/Closing through device menu
The shutter can be open/close to the desire percentage.
To open/close the shutter:
1. On the Home page, Tap All devices > Micromodule Shutter.
2. On the device menu, drag the sliding bar (A) up/down to set the desired
shutter opening/closing percentage.
3. Tap on Open/Mid-Open/Close (B) position to tilt the Slat (Only if the shutter
is installed with rotation slat).
Micro Module Shutter
A
B
Open
Mid-Open
Close
Setting up a schedule
The devices can be fully controlled by schedule. Once the schedule is set, the
devices operate at a given time.
To create a schedule:
1. On the Home page, Tap All devices > Micromodule Shutter.
2. Tap Schedule > Add Schedule to add a schedule.
3. In Add Schedule menu, set the time (A).
18
DUG_Wiser Micro Module Blind_PDL-00
Wiser Micro Module Blind
4. Tap Repeat (B) to select the days you want to set the schedule.
5. Tap Note (C), enter the note and tap Confirm.
6. Tap the toggle switch (D) to turn on the Notification for the schedule. The
app will send a notification that the scheduled task is executed at the time of
schedule.
7. Tap Control (E) and select any one option, Shutter Open / Shutter Close.
Add Schedule
Cancel
06
18
07
19
08
09
10
20
21
22
12
13
24
25
12
26
Save
AM
A
27
B
Repeat
C
Note
Once
D
E
0%
0%
100%
Close
Open
8. Tap Save
Creating a moment
A Moment allows you to group multiple actions that are usually done together.
Using the Wiser app, you can create moments based on your needs.
To create a moment:
1. On the Home page, tap
.
2. Go to Moment > + to create a moment.
3. Tap Edit name (A), enter the name of the moment and tap Save.
TIP: You can choose the cover image that best represents your moment by
tapping
Cancel
.
Moment settings
Save
Edit name
Action
(0/10)
Edit name
Add Task
A
Cancel
Save
4. In the Action section, tap Add task (B) to open the slide-up menu.
DUG_Wiser Micro Module Blind_PDL-00
19
Wiser Micro Module Blind
5. In the Add task menu, you can do either or all of the following actions (C):
– Run the device: select the devices that you want in a moment.
– Select Automation: select the automation that you want to enable or
disable.
– Delay: set the delay time.
NOTE: You can add one or more actions using
Cancel
Moment settings
.
Save
Edit name
Action
(0/10)
B
Add Task
Add Task
Run the device
C
Select Automation
Delay
6. Tap Run the device > Micromodule Shutter and select either or all the
functions to add in the moment:
– Control > Shutter Open / Shutter Close (D)
– Percentage > Set the percentage (E) of moment required.
Select function
D
E
20
Control
Next
Close
50%
DUG_Wiser Micro Module Blind_PDL-00
Wiser Micro Module Blind
7. Set all the actions and tap Save.
Cancel
Moment settings
Save
Micromodule Shutter Moment
Action
Show on Home Page
Editing a moment
1. On the Moment tab, locate the moment you want to edit and tap
.
2. On the Edit page, you can tap each item (such as dimmer, shutter, delay,
temperature, etc.) to change the settings.
TIP:
•
You can add one or more actions using
.
•
To delete an existing action, slide each item towards left and tap
Delete.
Deleting a moment
To delete a moment:
1. On the Moment tab, locate the moment that you want to delete and then tap
.
2. Tap Delete and then tap Ok.
NOTE: After deleting a moment, the device action can no longer be
triggered.
Creating an automation
An automation allows you to group multiple actions that are usually done together,
triggered automatically or at scheduled times. By using the Wiser app, you can
create automations based on your needs.
To create an automation:
1. On the Home page, tap the
.
2. Go to Automation > + to create an automation.
DUG_Wiser Micro Module Blind_PDL-00
21
Wiser Micro Module Blind
3. Tap Edit name (A), enter the name of the automation and tap Save.
TIP: You can choose the cover image that best represents your automation
by tapping
Cancel
.
Automation settings
Save
My Automation
Any condition is met
(0/10)
Edit name
Add Condition
A
Action
(Added
Save 0/80)
Cancel
Add Task
All-Day
4. Tap Any condition is met to select any one of the condition type (B):
– All conditions are met: the automation is triggered when all the
conditions are met.
– Any condition is met: the automation is triggered when at least one
condition is met.
Cancel
Automation settings
Save
My Automation
Any condition is met
(0/10)
Add Condition
(Added 0/80)
Action
Add Task
Select Condition type
All conditions are met
B
Any condition is met
Cancel
5. Tap Add Condition to open the slide-up menu.
22
DUG_Wiser Micro Module Blind_PDL-00
Wiser Micro Module Blind
6. In the Add Condition menu, you can do either or all of the following options
(C):
– When weather changes : select the various weather settings.
– Schedule: set the time and day.
– When device status changes: select the device and it’s function.
NOTE: You can add one or more conditions using
Cancel
Automation settings
.
Save
My Automation
Any condition is met
(0/10)
Add Condition
Add Condition
When weather changes
C
Schedule
When device status changes
7. Tap When device status changes > Micromodule Shutter > Percentage
and update the percentage of closing and opening of shutter.
Percentage
0
0%
Close
Next
%
100%
Open
8. Tap Add task to open the slide-up menu.
DUG_Wiser Micro Module Blind_PDL-00
23
Wiser Micro Module Blind
9. In the Add task menu, you can do either or all of the following options (D):
– Run the device: select the devices that you want to be triggered.
– Enable or disable Automation: select the automation that you want to
enable or disable.
– Send notification: turn on notification for the automation.
– Delay: set the delay time.
NOTE: You can add one or more actions using
Cancel
Automation settings
.
Save
My Automation
Any condition is met
(0/10)
Add Condition
Action
Add task
(Added 0/80)
Run the device
Add Task
Moment or Automation
D
All-Day
Delay
10. Tap on Effective period to set the time range for the automation. You can
select any one of the following (E):
– All-day - 24 hours
– Daytime - From sunrise to sunset
– Night - From sunset to sunrise
– Custom - User defined time period
Next
All-day
24 hours
Daytime
From sunrise to sunset
Night
From sunset to sunrise
E
Custom
Repeat
Everyday
City
11. Set all the actions and conditions and tap Save.
Automation is now available under Automation tab. Use toggle switch to
enable/disable automation.
24
DUG_Wiser Micro Module Blind_PDL-00
Wiser Micro Module Blind
Example of an automation
This demonstration shows you how to create an automation to open the
Micromodule Shutter at the scheduled time.
1. Go to Automation > + to create an automation.
2. Tap Edit name, enter the name of the automation and tap Save.
TIP: You can choose the cover image that best represents your automation
by tapping
.
3. Tap Add Condition > Schedule.
•
Tap Repeat (A), select the days you want to set the schedule and tap
Save.
•
Set the time (B) at which the automation must start and tap Next.
Schedule
A
Next
Repeat
Everyday
Execution Time
B
17
59
AM
18
00
PM
19
01
Note - Schedule is based on family location time zone.
4. Tap Add task > Run the device > Micromodule Shutter.
5. Tap Control > Shutter Open (C) and tap Save.
6. Tap Percentage (D) to update the percentage of shutter opening and tap
Save.
Select function
C
D
Control
Next
Close
100%
7. Tap Next.
DUG_Wiser Micro Module Blind_PDL-00
25
Wiser Micro Module Blind
8. In the Automation Settings page, tap Save.
Automation Settings
Cancel
Save
My Automation
Any condition is met
Action
Control: Open
All-Day
Automation is now available under Automation tab. Use toggle switch to
enable/disable automation.
Editing an automation
1. On the Automation tab, locate the automation you want to edit and tap
.
2. On the Edit page, you can tap each item (such as dimmer, shutter, delay,
temperature, etc.) to change the settings.
TIP:
•
You can add one or more condition or actions using
.
•
To delete an existing condition or action, slide each item towards left
and tap Delete.
Deleting an automation
1. On the Automation tab, locate the automation that you want to delete and
then tap
.
2. Tap Delete and then tap Ok.
NOTE: After deleting an automation, the device action can no longer be
triggered.
26
DUG_Wiser Micro Module Blind_PDL-00
Wiser Micro Module Blind
LED indication
Pairing the device
User Action
LED Indication
Status
Short press the push button 3 times.
LED blinks orange once per
second.
Pairing mode is active for 30 seconds. When
pairing is completed, LED glows green for a few
seconds before turning off.
User Action
LED Indication
Status
Short press the push button 3 times and hold it
down once for > 10 s.
LED blinks red once per second.
The device is in reset mode. The device then
restarts and LED turns orange indicating that the
device is ready for pairing.
Resetting the device
Troubleshooting
Symptom
No shutter movement or uncontrolled
shutter movement.
The device is not ready to pair after the
device is removed from the app.
DUG_Wiser Micro Module Blind_PDL-00
Solution
•
Check power supply.
•
Check the wiring between module and push-button switch..
•
Check the load
Reset to factory default settings, refer to Resetting the device, page 16
27
Wiser Micro Module Blind
Technical data
Nominal voltage
AC 220-240 V, 50/60 Hz
Nominal current
4 A, cosφ = 0.6 - 1.0
Blind channel
1, mechanically and electronically locked against each other
Standby
Max. 0.3 W
Operating Temperature
0 ºC to 35 ºC
Neutral conductor
Required
Connecting terminals
Max. 2 x 2.5 mm2, solid or stranded types
Extension connection
Max. 10 mechanical double push-button switches
Length of all cable sections
Max. 50 m for 3-wire NYM cable
Fuse protection
16 A circuit breaker
Operating frequency
2405 - 2480 MHz
Max. radio-frequency power transmitted
<10 mW
IP rating
IP20
Product dimensions (H x W x D)
43 x 43 x 22 mm
Communication protocol
Zigbee 3.0 certified
28
DUG_Wiser Micro Module Blind_PDL-00
Wiser Micro Module Blind
Compliance
Compliance information for Green Premium products
Find and download comprehensive information about Green Premium products,
including RoHS compliance and REACH declarations as well as Product
Environmental Profile (PEP) and End-of-Life instructions (EOLI).
https://checkaproduct.se.com/
General information about Green Premium products
Click the link below to read about Schneider Electric’s Green Premium product
strategy.
https://www.schneider-electric.com/en/work/support/green-premium/
Trademarks
This guide makes reference to system and brand names that are trademarks of
their relevant owners.
•
Zigbee® is a registered trademark of the Connectivity Standards Alliance.
•
Apple® and App Store® are brand names or registered trademarks of Apple
Inc.
•
Google Play™ Store and Android™ are brand names or registered
trademarks of Google Inc.
•
Wi-Fi® is a registered trademark of Wi-Fi Alliance®.
•
Wiser™ is a trademark and the property of Schneider Electric, its subsidiaries
and affiliated companies.
Other brands and registered trademarks are the property of their respective
owners.
DUG_Wiser Micro Module Blind_PDL-00
29
Schneider Electric (NZ) Ltd
Building 6
Level 2. 60 Highbrook Drive, East Tamaki, Auckland 2013
New Zealand
Customer Care: 13 73 28
www.pdl.co.nz
As standards, specifications, and design change from time to time,
please ask for confirmation of the information given in this publication.
© 2023 – 2023 Schneider Electric. All rights reserved.
DUG_Wiser Micro Module Blind_PDL-00