Electrolux | EFA9620 | User manual | Electrolux EFA9620 User manual

USER MANUAL
EFA9620
electrolux 3
EN
RECOMMENDATIONS AND SUGGESTIONS
6
CHARACTERISTICS
7
USE
12
MAINTENANCE
14
IT
4 electrolux
EN
Welcome to the world of Electrolux
Thank you for choosing a first class
product from Electrolux, which hopefully will provide you with lots of pleasure
in the future. The Electrolux ambition is
to offer a wide variety of quality products that make your life more comfortable. You find some examples on the
cover in this manual. Please take a few
minutes to study this manual so that
you can take advantage of the benefits
of your new machine. We promise that
it will provide a superior User Experience delivering Ease-of-Mind.
Good luck!
electrolux 5
6 electrolux Recommendations and Suggestions
RECOMMENDATIONS AND SUGGESTIONS
Installation
• The manufacturer will not be held liable for any damages resulting from
EN
incorrect or improper installation.
• The minimum safety distance between the cooker top and the extractor hood is 650 mm.
• Check that the mains voltage corresponds to that indicated on the rating
plate fixed to the inside of the hood.
• For Class I appliances, check that the
domestic power supply guarantees
adequate earthing.
Connect the extractor to the exhaust
flue through a pipe of minimum diameter 120 mm. The route of the flue
must be as short as possible.
• Do not connect the extractor hood to
exhaust ducts carrying combustion
fumes (boilers, fireplaces, etc.).
• If the extractor is used in conjunction
with non-electrical appliances (e.g.
gas burning appliances), a sufficient
degree of aeration must be guaranteed in the room in order to prevent
the backflow of exhaust gas. The
kitchen must have an opening communicating directly with the open air in
order to guarantee the entry of clean
air.
Use
• The extractor hood has been designed exclusively for domestic use to
eliminate kitchen smells.
• Never use the hood for purposes
other than for which it has ben designed.
• Never leave high naked flames under
the hood when it is in operation.
• Adjust the flame intensity to direct it
onto the bottom of the pan only, making sure that it does not engulf the
sides.
• Deep fat fryers must be continuously
monitored during use: overheated oil
can burst into flames.
• Do not flambè under the range hood;
risk of fire
• The hood should not be used by children or persons not instructed in its
correct use.
Maintenance
• Switch off or unplug the appliance
from the mains supply before carrying
out any maintenance work.
• Clean and/or replace the Filters after
the specified time period.
• Clean the hood using a damp cloth
and a neutral liquid detergent.
The symbol
on the product or on its
packaging indicates that this product may
not be treated as household waste. Instead
it shall be handed over to the applicable
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for
the environment and human health, which
could otherwise be caused by inappropriate
waste handling of this product. For more
detailed information about recycling of this
product, please contact your local city office,
your household waste disposal service or
the shop where you purchased the product.
Characteristics electrolux
7
CHARACTERISTICS
Dimensions
EN
8 electrolux Characteristics
Components
21
Ref. Q.ty Product Components
1 Hood Body, complete with: ConEN 1
trols, Light, Blower, Filters
2
1 Telescopic Chimney comprising:
2.1 1 Upper Section
2.2 1 Lower Section
7.1 1 Telescopic frame complete with
extractor, consisting of:
7.1a 1 Upper frame
7.1b 1 Lower frame
9
1 Reducer Flange ø 150-120 mm
10
1 Flange ø 150
15
1 Air Outlet Connection
24
1 Junction box
25
2 Pipe clamps
Ref. Q.ty
11
4
12c 6
12e 2
12f 4
12g 4
12h 4
21
1
22
4
23
4
23
12h
7.1a
15
12g
7.1
10
7.1b
9
25
12c
2.1
Installation Components
Wall Plugs ø 10
Screws 2,9 x 6,5
Screws 2,9 x 9,5
Screws M6 x 10
Screws M6 x 80
Screws 5,2 x 70
Drilling template
6.4 mm int. dia washers
M6 nuts
Q.ty Documentation
1 Instruction Manual
11
22
2
2.2
12e
12c
12c
1
12f
24
Installation electrolux
9
INSTALLATION
Drilling the Ceiling/shelf
• Use a plumb line to mark the centre of
the hob on the ceiling/support shelf.
• Place the drilling template 21 provided
on the ceiling/support shelf, making
sure that the template is in the correct
position by lining up the axes of the
template with those of the hob.
• Mark the centres of the holes in the
template.
• Drill the holes at the points marked:
• for concrete ceilings, drill for plugs
appropriate to the screw size.
• for hollow brick ceilings with wall
thickness of 20 mm: drill ø 10
mm(immediately insert the Dowels
11 supplied).
• for wooden beam ceilings, drill according to the wood screws used.
• for wooden shelf, drill ø 7 mm.
• for the power supply cable feed, drill
ø 10 mm.
• for the air outlet (Ducted Version),
drill according to the diameter of the
external air exhaust duct connection.
• Insert two screws of the following
type, crossing them and leaving 4-5
mm from the ceiling:
• for concrete ceilings, use the appropriate plugs for the screw size (not
provided).
• for Cavity ceiling with inner space,
with wall thickness of approx. 20
mm, Screws 12h, supplied.
• for wooden beam ceilings, use 4
wood screws (not provided).
• for wooden shelf, use 4 screws 12g
with washers 22 and nuts 23, provided.
EN
10 electrolux Installation
Fixing the frame
• Loosen the two screws fastening the
lower chimney and remove this from
the lower frame.
EN
• Loosen the two screws fastening the
upper chimney and remove this from
the upper frame.
If you wish to adjust the height of the
frame, proceed as follows:
• Unfasten the eight metric screws joining the two columns, located at the
sides of the frame.
• Adjust the frame to the height required, then replace all the screws
removed as above.
• Insert the upper chimney stack from
above, and leave it running free on the
frame.
• Lift up the frame, fit the frame slots
onto the screws up to the slot end
positions.
• Tighten the two screws and fasten
the other two screws provided with
the hood.
Before tightening the screws completely
it is possible to adjust the frame by turning it. Make sure that the screws do
not come out of their seats in the slotted
holes.
• The frame mountings must be secure
to withstand the weight of the hood
and any stresses caused by the occasional side thrust applied to the
device.
On completion, check that the base is
stable, even if the frame is subjected
to bending.
• In all cases where the ceiling is not
strong enough at the suspension
point, the installer must provide
strengthening using suitable plates
and backing pieces anchored to the
structurally sound parts.
1
2
1
2
Installation electrolux
11
Connection in Ducting Version
When installing the ducting version,
connect the hood to the chimney using
either a flexible or rigid pipe ø 150 or
120 mm, the choice of which is left to
the installer.
• To install a ø 120 mm air exhaust connection, insert the reducer flange 9 on
the hood body outlet.
• Fix the pipe using the pipe clamps 25
provided.
• Remove charcoal filters, if present.
ø 150
ø 120
25
9
25
Connection in Recycling Version
• Fix the connection 15 to the frame
using the 4 screws provided.
• Fix the flange 10 to the lower opening
of the connection 15.
• Connect the hood air outlet to the
flange in the lower part of the junction
using a rigid or flexible ø 150 tube (by
installer’s choice).
• Ensure that the charcoal filters have
been fitted.
15
10
Chimney assembly / Mounting
the hood body
• Position the upper chimney section
and fix the upper part to the frame
using the 2 screws 12c (2,9 x 6,5)
provided.
• Similarly, position the lower chimney
section and fix the lower part to the
frame using the 2 screws 12c (2,9 x
6,5) provided.
Before fixing the hood body to the frame:
• Remove the grease filters from the
hood body.
• Remove charcoal filters, if present.
• From below, use the 4 screws 12f
(M6 x 10)provided to fix the hood
body to the frame.
12c
12c
1
12f
EN
12 electrolux Installation / Use
Electrical Connection
• Connect the hood to the mains
through a two-pole switch having a
EN
contact gap of at least 3 mm.
• Remove the grease filters (see paragraph Maintenance) being sure that
the connector of the feeding cable is
correctly inserted in the socket placed
on the side of the fan.
• Connect the control connector Cmd.
• Connect the lights connector Lux.
• Place the connectors in the junction
box 24 and close it using the 2 screws
12e (2,9 x 9,5) provided.
• Fix the junction box to the hood body
using the 2 screws 12c (2,9 x 6,5)
provided.
• For the recirculation version, fit the
activated carbon odour filter.
• Replace the grease filters.
24
12e
Lux
12c
USE
The hood can be switched on pushing
directly onto the requested speed
without firstly having to select 0/1 button
L T1 T2 T3 T4 T5 F
Cmd
Use electrolux
Touch Basic functions
control
Dual Function
L When briefly pressed it switches the lighting
system on and off.
When pressed for 2 seconds it starts the
lighting system in “courtesy light” mode.
The lamps are fed at a reduced power of
approximately 5W. Such function can be
stopped by pressing the touch control for 2
seconds or just by pressing it shortly in order to
return to the normal lighting mode. In courtesy
light mode the touch control is not lit.
T1 When pressed the motor is stopped, regardless
of the speed it is set to.
Indicator lights
Touch control
unlit
Touch control lit
Lights off
Lights on
EN
Touch control
unlit
Touch control lit
Touch control
unlit
Courtesy light on
Motor on
Motor off
T2
When pressed the motor is set to the first speed
T3
By a brief pressing the motor is set to the second Touch control lit
Second speed on
speed.
By pressing the touch control for approximately
Flashing touch
Delay function on
control
2 seconds the Delay function is enabled, i.e
delayed shutdown of the appliance ensuring
a complete elimination of the residual odours.
This function can be activated at OFF-position
and at 1°, 2° and 3°speeds. It can be stopped
in advance by pressing any of the touch
controls (T) with the exception of T3. The Delay
function works according to the following
scheme:
1°speed / OFF
=
20 minuets
2°speed
=
15 minutes
3°speed
=
5 minutes
When pressed the motor is set to the third speed
Touch control lit
T4
T5
F
When pressed the motor is set to the intensive
speed timed to 5 minutes. At the end of 5
minutes of intensive speed the hood starts again
at the speed it was set to previously. In case the
hood is set to the intensive speed directly from
OFF-state it will then start from the first speed
after 5 minutes of intensive speed.
When pressed for 4 seconds it resets the filter
alarm signal indicated by flashing of the touch
control T1. This procedure can be carried out
only when the motor is stopped.
13
Touch control lit
Touch control lit
Touch control lit
Flashing touch
control
Metal grease filters saturation
alarm. Metal grease filters need
to be washed. The alarm starts
up after 100 working hours.
Charcoal filter saturation
alarm. Charcoal filter has to
be replaced and metal grease
filters washed. The alarm
starts up after 200 working
hours. (Activation; check the
paragraph “Charcoal filter”)
14 electrolux Maintenance
MAINTENANCE
Cleaning the Comfort Panels
• Pull the Comfort Panel to open it.
• Disconnect the panel from the hood
EN
canopy by sliding the fixing pin lever.
• The comfort panel must never be
washed in a dishwasher.
• Clean the outside using a damp cloth
and neutral liquid detergent.
• Clean the inside as well using a damp
cloth and neutral detergent; do not
use wet cloths or sponges, or jets of
water; do not use abrasive substances.
• When the above operation has been
completed, hook the panel back to
the hood canopy and close it by turning the knob in the opposite direction.
Cleaning of the Metal Cassette
Filters
Alarm reset
• Stop the motor.
• Press the F -touch control for at least
4 seconds until the T1 -touch control
flashes.
Cleaning the filters
• Filters can be washed in the dish machine. They need to be washed every
2 months or even more frequently in
case of particularly intensive use of
the hood.
• Pull the Comfort Panel to open it.
• Remove the filters one by one pushing
them lateraly and simultaneously pulling downwards.
• Any kind of bending of the filters has
to be avoided when washing them.
Before fitting them again into the hood
make sure that they are completely
dry (The colour of the filter surface
may change throughout the time but
this has no influence to the filter efficiency).
• When fitting the filters into the hood
pay attention that they are placed in
correct position and that the handle
faces outwards.
• Close the comfort panel.
Maintenance electrolux
Replacing the Charcoal Filter
This filter cannot be washed or regenerated, and must be replaced when the F
touch control starts to flash, or at least
once every 4 months. The alarm is only
triggered when the motor is on.
Enabling/Disabling the alarm signal
• In Recirculation Version Hoods, the
Filter saturation Alarm must be enabled at the time of installation or later.
• Switch off the lights and the motor.
• Disconnect the mains power supply
to the hood by removing the motor
unit power supply cable connector,
switching off the power supply at the
Mains or turning the Main switch off.
• Restore the connection, pressing and
holding T2.
• Release the touch control, touch
controls L, T2 and F will light up normally.
• Within 3 seconds press the touch
control F until the key itself flashes to
confirm as follows:
• 2 flashes – Charcoal Filter saturation
Alarm ENABLED
• 1 flash - Charcoal Filter saturation
Alarm DISABLED
15
Reset the alarm signal
• Stop the motor.
• Press the touch control F for at least
4 seconds, until the touch control T1
flashes.
Replace the Filter
• Pull the Comfort Panel to open it.
• Remove the metal grease filters.
• Remove the saturated charcoal filter,
turning the fasteners provided.
• Fit the new filter and fasten it its correct position.
• Put the metal grease filters in their
seats.
• Close the comfort panel.
Light replacement
20 W halogen light.
• Remove the snap-on lamp cover by
levering it from under the metal ring,
supporting it with one hand.
• Remove the halogen lamp from the
lamp holder by pulling gently.
• Replace the lamp with a new one of
the same type, making sure that you
insert the two pins properly into the
housings on the lamp holder.
• Replace the snap-on lamp cover.
EN
16 electrolux
www.electrolux.com
436003562_03 - 070130
Download PDF