Samsung | ML1710 | Remanufacturing Instructions

Remanufacturing Instructions
Samsung ML 1710/1750 Toner Cartridge
For Technical Support, please call Memphis, TN at (888) 757-0762 or Nashua, NH at (888) 833-5727.
OEM Reference Information
OEM Product #: ML-1710D3/XAA
OEM Yield: 3,000 pages @ 5% coverage
Fig. 1
1. Remove the five screws (highlighted
area in Fig. 1) on the top cover of the toner
cartridge. The cover will not come off, as
there are four clips that need to be released
for the cover to be removed.
Fig. 2
2. Using a small flat head screwdriver,
gently push in the release clips located on the
back of the cover.
NOTE: Be careful not to break these clips.
Toner will leak out if they are broken.
3.
© 2004 Oasis Imaging Products, Inc.
Page 1 of 1
Remanufacturing Instructions
Samsung ML 1710/1750 Toner Cartridge
Technical Support
Memphis, TN (888) 757-0762
Nashua, NH (888) 833-5727
3. The other clips are located on the front
of the cartridge. Remove them in the same
manner as in the previous step.
Fig. 3
4.
4. After removing the screws and clips,
simply pull the top cover up to remove.
NOTE: The Samsung ML 1710/1750 toner
cartridge is designed with an open hopper,
similar to the HP PX/VX series of cartridges.
Use caution when removing the lid as any
excess toner may spill out.
5. Remove any residual toner from the waste
and supply sides at this time.
Fig. 4
Fig. 5
6. Detach the side cap by removing the three
screws that secure it to the main cartridge
body.
© 2004 Oasis Imaging Products, Inc.
Page 2 of 2
Remanufacturing Instructions
Samsung ML 1710/1750 Toner Cartridge
Fig. 6
Technical Support
Memphis, TN (888) 757-0762
Nashua, NH (888) 833-5727
7. Remove the side cap on the opposite end
of the cartridge using the same instructions.
NOTE: Be careful removing the side cap as
some of the drive gears are not attached and
will fall off.
8. Once both side plates are detached,
remove the PCR.
NOTE: The PCR has a small drive gear
attached to it. This gear is stationary and will
not fall off. During the reassembly of this
cartridge, align the PCR drive gear with the
small helical spur gear on the OPC.
Fig. 7
Fig. 8
9. The developer roller stabilizer plate
must be removed to remove the developer
roller and OPC. Insert a small flathead
screwdriver under the plate and gently pry
off.
NOTE: Be careful not to break the plastic
clip that secures it to the cartridge body.
© 2004 Oasis Imaging Products, Inc.
Page 3 of 3
Remanufacturing Instructions
Samsung ML 1710/1750 Toner Cartridge
Technical Support
Memphis, TN (888) 757-0762
Nashua, NH (888) 833-5727
10. After removing the developer roller side
plate, remove the developer roller by pulling
the shaft through the area that was covered
by the stabilizer plate.
NOTE: Be sure to remove the developer
roller drive gear from the geared side of the
cartridge before sliding the roller out.
Fig. 9
Fig. 10
11. To remove the OPC, simply push it up
from the bottom of the cartridge and pull it
out the top. To maintain optimum print
quality and reliability, it is recommended to
change it out each cycle.
12. After removing the OPC, finish cleaning
the toner hopper area.
NOTE: It is not recommended to remove
the Doctor Blade during the remanufacturing
process. Removal can cause damage to the
sealing foams.
© 2004 Oasis Imaging Products, Inc.
NOTE: Pay careful attention to the sponge
toner delivery roller in the toner hopper.
Manually rotate this roller during the
cleaning process to ensure that all of the old
toner is removed from the sponge roller.
13. You can clean any toner from the
working edge of the blade with a Q-tip.
Page 4 of 4
Remanufacturing Instructions
Samsung ML 1710/1750 Toner Cartridge
Fig. 11
Technical Support
Memphis, TN (888) 757-0762
Nashua, NH (888) 833-5727
NOTE: The wiper blade assembly in this
cartridge is very different than most
cartridges. Not only is there a PCR cleaner
attached to the blade stamping, the blade
itself is little more than an enlarged
recovery blade. The toner has a very high
transfer rate so there is very little waste in
the waste toner collection.
14. The working edge of the blade is very
fragile and easily damaged so be careful
during the removal /cleaning process.
15. After cleaning out all the residual toner
and inspecting the components, refill with
toner and reassemble in reverse order.
Fig. 12
Oasis and You … Succeeding Together!
© 2004 Oasis Imaging Products, Inc.
Page 5 of 5
New Hampshire
(603) 880-3991
(888) 627-6555
Fax: (603) 598-4277
Tennessee
(901) 433-0334
Fax: (901) 366-9756
Texas
(972) 671-1307
(888) 591-3555
Fax: (972) 671-1359
Canada
(905) 568-3422
(800) 430-7886
Fax: (905) 568-3491
Illinois
(630) 982-1543
(888) 658-4555
Fax: (630) 928-1542
California
(714) 283-6270
(888) 656-9555
Fax: (714) 283-6276
North Carolina
(919) 776-0847
(866) 399-8558
Fax: (919) 776-0898
Europe
Netherlands
011-31-24-388-2233
Fax: 011-31-24-355-7373
© 2004 Oasis Imaging Products, Inc. Any attempt to reproduce any part of these instructions without the written consent of Oasis
Imaging Products, Inc. may result in legal action. All registered trademarks are the property of their respective owners.
© 2004 Oasis Imaging Products, Inc.
Page 6 of 6
Download PDF