Digital Monitoring | XR6 | Installation guide | Digital Monitoring XR6 Installation guide

INSTALLATION GUIDE
XR6 COMMAND PROCESSOR™ PANEL and
XR10 COMMAND PROCESSOR™ PANEL
MODEL XR6/XR10
COMMAND PROCESSOR
INSTALLATION GUIDE
FCC NOTICE
This equipment generates and uses radio frequency energy and, if not installed and used
properly in strict accordance with the manufacturer's instructions, may cause interference
with radio and television reception. It has been type tested and found to comply with the limits
for a Class B computing device in accordance with the specification in Subpart J of Part 15
of FCC Rules, which are designed to provide reasonable protection against such interference
in a residential installation. If this equipment does cause interference to radio or television
reception, which can be determined by turning the equipment off and on, the installer is
encouraged to try to correct the interference by one or more of the following measures:
Reorient the receiving antenna
Relocate the computer with respect to the receiver
Move the computer away from the receiver
Plug the computer into a different outlet so that computer and receiver are on
different branch circuits
If necessary, the installer should consult the dealer or an experienced radio/television
technician for additional suggestions. The installer may find the following booklet, prepared
by the Federal Communications Commission, helpful:
"How to identify and Resolve Radio-TV Interference Problems."
This booklet is available from the U.S. Government Printing Office, Washington D.C.
20402
Stock No. 004-000-00345-4
Copyright © 1995 - 2002 Digital Monitoring Products, Inc.
Information furnished by DMP is believed to be accurate and reliable.
This information is subject to change without notice.
Section
TABLE OF CONTENTS
Page
Panel Specifications ............................................................................... 1
1.1
Power Supply ................................................................. 1
1.2
Communication .............................................................. 1
1.3
Panel Zones ................................................................... 1
1.4
Keypads ........................................................................ 1
1.5
Outputs ......................................................................... 1
1.6
Enclosure Specifications ................................................... 1
Introduction ............................................................................................ 2
2.1
Description .................................................................... 2
2.2
System Configurations ..................................................... 2
2.3
Before you Begin ............................................................ 2
2.4
About this Guide ............................................................. 2
2.5
How to use this Guide ...................................................... 2
System Components ............................................................................... 3
3.1
Description .................................................................... 3
3.2
Wiring Diagram ............................................................... 3
3.3
Lightning Protection ........................................................ 3
3.4
Command Processor Accessories ........................................ 3
3.5
XR6/XR10 Wiring Diagram ................................................. 4
Installation .............................................................................................. 5
4.1
Mounting the Enclosure .................................................... 5
4.2
Mounting Keypads ........................................................... 6
4.3
Wiring Keypads ............................................................... 6
Primary Power Supply ............................................................................ 6
5.1
AC Terminals 1 and 2 ....................................................... 6
5.2
Transformer Types ........................................................... 6
Secondary Power Supply ....................................................................... 7
6.1
Battery Terminals 3 and 4 ................................................. 7
6.2
Earth Ground ................................................................. 7
6.3
Replacement Period ........................................................ 7
6.4
Discharge/Recharge ........................................................ 7
6.5
Battery Supervision ......................................................... 7
6.6
XR6/XR10 Power Requirements .......................................... 7
6.7 XR6/XR10 Standby Battery Calculations .................................... 8
Bell Output ............................................................................................... 9
7.1
Terminals 5 and 6 ........................................................... 9
Keypad Data Bus ..................................................................................... 9
8.1
Description .................................................................... 9
8.2
Terminal 7 - RED ............................................................. 9
8.3
Terminal 8 - YELLOW ....................................................... 9
8.4
Terminal 9 - GREEN ......................................................... 9
8.5
Terminal 10 - BLACK ........................................................ 9
8.6
Programming Connection .................................................. 9
Smoke and Glassbreak Detector Output .............................................. 9
9.1
Terminal 11 .................................................................... 9
Burglary Zones ...................................................................................... 10
10.1
Description ................................................................... 10
10.2
Operational parameters .................................................. 10
10.3
Zone Response Time ....................................................... 10
10.4
Keyswitch Arming Zone ................................................... 10
Digital Monitoring Products
XR6/XR10 Installation Guide
iii
Section
TABLE OF CONTENTS
Page
Powered Zone for 2-Wire Smoke Detectors ...................................... 11
11.1
Terminals 25 and 26 ....................................................... 11
Annunciator Outputs ............................................................................ 12
12.1
Description ................................................................... 12
12.2
Harness Wiring .............................................................. 12
12.3
Model 860 Relay Module .................................................. 12
Telephone RJ Connector ...................................................................... 12
13.1
Description ................................................................... 12
13.2
FCC Registration ............................................................ 13
13.3
Notification .................................................................. 13
13.4
Ground Start ................................................................. 13
Reset Jumpers J16 ................................................................................ 13
14.1
Description ................................................................... 13
UNIVERSAL UL BURGLARY SPECIFICATIONS .................................... 14
15.1
Introduction .................................................................. 14
15.2
Wiring .......................................................................... 14
15.3
Police station phone numbers .......................................... 14
15.4
Bypass reports ............................................................... 14
15.5
System maintenance ....................................................... 14
15.6
Cross zoning.................................................................. 14
15.7
Ground Start ................................................................. 14
15.8
UL Listed Receivers ........................................................ 14
UL 1023 SPECIFICATIONS
Household Burglar-Alarm System Units ............................................. 14
16.1
Bell cutoff .................................................................... 14
16.2
Entry delay ................................................................... 14
16.3
Exit delay ..................................................................... 14
16.4
Zone expansion on 4-wire bus .......................................... 14
UL 1610 and 1076 specifications
Central-Station and Proprietary Burglar-Alarm Units ...................... 15
17.1
Opening/Closing reports ................................................. 15
17.2
Automatic bell test ........................................................ 15
17.3
Proprietary dialer .......................................................... 15
UL 1635 SPECIFICATIONS
Digital Burglar Alarm Communicator System Units ......................... 15
18.1
Digital Dialer telephone number ....................................... 15
18.2
Entry delay ................................................................... 15
18.3
Exit delay ..................................................................... 15
18.4
Test frequency .............................................................. 15
18.5
Automatic bell test ........................................................ 15
18.6
Grade B Central Station .................................................. 15
UL 365 and 609 SPECIFICATIONS
Police Station Connected and Local Burglar Alarm Units
and Systems .......................................................................................... 16
19.1
Entry delay ................................................................... 16
19.2
Grade A bell .................................................................. 16
19.3
Bell cutoff .................................................................... 16
19.4
Automatic bell test ........................................................ 16
19.5
Grade A Mercantile ......................................................... 16
19.6
Mercantile Safe and Vault ................................................ 16
19.7
Line security for Police Connect ....................................... 16
XR6/XR10 Installation Guide
iv
Digital Monitoring Products
Section
TABLE OF CONTENTS
Page
UNIVERSAL UL and NFPA FIRE ALARM SPECIFICATIONS ................ 17
20.1
Introduction .................................................................. 17
20.2
Wiring .......................................................................... 17
20.3
Police station phone number ............................................ 17
20.4
System maintenance ....................................................... 17
20.5
Audible alarm ............................................................... 17
20.6
Fire zone programming ................................................... 17
20.7
Ground Start ................................................................. 17
20.8
UL Listed Receivers ........................................................ 17
UL 985 NFPA 72 (chapter 2) SPECIFICATIONS
Household Fire Warning System Units ............................................... 17
21.1
Bell output definition ..................................................... 17
21.2
Indicating Circuit Supervision .......................................... 17
CALIFORNIA STATE FIRE MARSHAL SPECIFICATIONS .................... 17
22.1
Bell output definition ..................................................... 17
23.1
Multiple Indicating Circuit Module Installation .................... 18
23.2
Installation for Derived Channel burglary ........................... 19
24.1
Troubleshooting ............................................................. 20
Digital Monitoring Products
XR6/XR10 Installation Guide
v
This page left intentionally blank.
INTRODUCTION
Panel Specifications
1.1
Power Supply
Transformer Input:
16.5 VAC 40VA (Models 320 wire-in or 321 plug-in)
16.5 VAC 20VA (Model 324 plug-in)
Standby Battery:
12 VDC 7.0Ah (40VA transformer charges up to 2 batteries)
Auxiliary Output:
12 VDC at 500mA
Bell Output:
12 VDC at 1.5 Amps with 40VA transformer, 600mA with 20VA transformer
Smoke Detector Output: 12 VDC at 100mA
All circuits inherent power limited
1.2
Communication
Built-in SDLC Digital Dialer communication to DMP Model SCS-1 Receivers
Built-in 4-2 communication to non-DMP receivers
Built-in CID (Contact ID) communication to non-DMP receivers
Any panel can operate as a local system.
1.3
Panel Zones
Nine 1k Ω EOL burglary zones (zones 1 to 9 on XR10, and zones 1 to 5 on XR6)
One 3.3k Ω EOL Class B powered fire zone with reset capability (zone 10 on XR10, and zone 6 on XR6)
1.4
Keypads
You can connect up to four supervised keypads to the XR6/XR10 panels.
• 16 or 32 character alphanumeric keypads
• 10-zone LED keypads
In addition, the following zone expanders can be added to the XR6 panel:
• Four and single point zone expanders
• Single point PIR and glassbreak detectors
• One 738A Ademco Wireless interface for up to 32 points of zone expansion
• One FA426 Wireless receiver for up to 16 points of zone expansion
1.5
Outputs
The XR6/XR10 panels provide four open collector outputs rated for 50mA each. A Model 300 Output Harness is required.
The open collector outputs provide the ground connection for a positive voltage source.
1.6
Enclosure Specifications
The XR6/XR10 panel ships in an enclosure with EOL resistors, battery leads, user's guide, and programming sheet.
Size:
12.5" W x 11.5" H x 3.5" D
Weight:
4 lbs
Color:
Gray or Black
Construction:
20 gauge cold rolled steel
XR6/XR10 Installation Guide
Digital Monitoring Products
1
INTRODUCTION
Introduction
2.1
Description
The DMP XR6/XR10 Command Processor® panels are powerful 12 VDC burglary and fire communicator panels with
battery backup. The XR10 provide nine on-board burglary zones and one on-board 12 VDC Class B powered fire zone.
The XR6 provides five burglary and one fire zone. The fire zone has a reset capability to provide for 2-wire smoke
detectors, relays, or other latching devices. The panels can communicate to one or two DMP SCS-1 Receivers using
SDLC digital dialer, 4-2, or Contact ID (CID) reporting formats.
2.2
System Configurations
The panels can be programmed to operate as either an All/Perimeter system that provides one Perimeter area and one
Interior area, or as a Home/Sleep/Away system that provides one Perimeter, one Interior, and one Bedroom area. The
Bedroom area can include any protection devices the user wants disarmed during their sleeping hours and armed in the
Away mode.
2.3
Before you Begin
Before installing the panel, we recommend you read through the entire contents of this guide. Familiarize yourself with
the features of the panel and the key points to remember during the installation. Be sure to read and understand all of
the caution statements printed in bold italics.
In addition to this installation guide, you should also read through and familiarize yourself with these other product
documents:
• XR6/XR10 Programming Guide (LT-0230)
• XR6/XR10 Program Information Sheet (LT-0212)
• XR6/XR10 Security Command User's Guide (LT-0226)
2.4
About this Guide
The information contained in this guide is organized into three sections: Table of Contents, Introduction, and
Installation.
• The Table of Contents at the front of this guide lists all of the headings and subheadings used throughout
each section and the page number where the information can be found.
• The Introduction section gives you an overview of the various components that go into a
panel system and diagrams some typical system configurations. This section gives descriptions of the
panel, keypads, and accessory modules and provides details on how each of them operate together in the
system.
• The Installation section begins with mounting instructions for the enclosure and takes you through the
proper way to power up the panel prior to programming.
Caution notes
Throughout this guide you will see caution notes containing information you need to know when installing the
panel. These cautions are written with a bold, italicized introductory clause followed by a detailed description of the
caution. See the example shown below.
Always ground the panel before applying power to any devices: The panel must be properly grounded before
connecting any devices or applying power to the panel. Proper grounding protects against Electrostatic Discharge (ESD)
that can damage system components.
Whenever you see a caution note, make sure you completely read and understand its information. Failing to follow the
caution note can cause damage to the equipment or improper operation of one or more components in the system.
2.5
How to use this Guide
To locate information about the installation of the panel, first go to the Table of Contents at the front of this guide.
Find the subject heading that closely describes the information you need and turn to the section number shown to the
right of the heading.
The text that follows the heading has been written to provide as much information about the subject as possible. If you
can't find the information you need under that heading, try scanning through a few of the headings before and after
and reading the text under those that sound similar.
Digital Monitoring Products
2
XR6/XR10 Installation Guide
INTRODUCTION
System Components
3.1
Description
The DMP system is made up of an alarm panel with built in communicator, an enclosure, a 16.5 VAC transformer, and a
12 VDC 7.0 Ah battery. You can add Security Command keypads to the system and can also connect auxiliary devices to
the panel's open collector outputs to expand the basic system. Combined current requirements of additional modules
may require an auxiliary power supply. Refer to the Standby Battery Power Calculation section in this guide when
calculating power requirements. In addition, up to 4 points of zone expansion can be added to the XR6.
3.2
Wiring Diagram
The system wiring diagram in Figure 1 shows some of the accessory devices you can connect for use in various
applications. A complete description of each module follows. Zone expanders as well as wireless zones can be added to
the XR6.
3.3
Lightning Protection
Metal Oxide Varistors and Transient Voltage Suppressors help protect against voltage surges on input and output
circuits. A transorb is provided for the Smoke Detector Output Circuit (Terminal 11). This transient protection provides
additional resistance to electrical surges such as lighting. Additional surge protection is available by installing the DMP
370 or 370RJ Lightning Suppressors.
3.4
Command Processor Accessories
You can connect any combination of up to four Model 670, 770, and 771 vacuum fluorescent, 790, 791, and 793 LCD, or
692 LED Security Command Keypads to the 4-wire keypad data bus provided by the panel on terminals 7, 8, 9, and 10.
Also, you can connect Model 714, 715, 714-8, 714-16, 715-8, 715-16 zone expanders to the XR6 keypad bus.
Additionally, you can connect one Model 738A Ademco Interface Module or one Model FA426 Wireless Receiver to the
XR6 keypad bus.
Note: The XR10 does not support zone expansion on the keypad bus.
XR6/XR10 Installation Guide
Digital Monitoring Products
3
INTRODUCTION
3.5
XR6/XR10 Wiring Diagram
The Class 2, Class 3, and power-limited fire alarm circuits are installed using CL3,
CL3R, or CL3P, or substitute cable permitted by the National Electric code, ANSI/
NFPA 70, and the Class 2, Class 3, and power-limited fire alarm circuit conductors
extending beyond the cable jacket are separated a minimum of 1/4 in. or by
nonconductive tubing or by a nonconductive barrier.
Output Header J11
All outputs must be connected to
devices located within the same
room as the control panel.
DMP
transformers:
Model 320
16.5 VAC 40VA
Class 2 wire-in
1K Ω 1K Ω
GND
Up to 500mA auxiliary
current at 10.4 - 13.2
VDC from Terminal 7.
An alarm sounding
device must be
installed indoors so
that it is clearly
heard in all sleeping
areas.
Z4
Z5
GND
1K Ω 1K Ω 1K Ω 1K Ω
Smoke Output
100mA @ 10.4 - 13.2
VDC Terminal 11
Z6
1K Ω
1K Ω
EPROM
Socket
See detail below
for XR6 panel
only
ZONE 5
Z3
ZONE 3
ZONE 2
Z2
Red
Black
4-wire smoke
detector
Smoke
Power
Supervision Detector
+Relay
Bell
Household System
ZONE 1
22 GA. MIN BLACK
22 GA. MIN YELLOW
-B BELL GND RED YEL GRN BLK SMK Z1 GND
22 GA. MIN GREEN
RED
16 - 18 gauge
wire
Maximum AC wire
distance
With 16 gauge wire: 70
feet
Bell
With 18 gauge wire: 40
Cold Water Pipe Earth
10.4 - 13.2 VDC feet
Ground
Total current:
+B
22 GA. MIN RED
AC
BLACK
AC
ZONE 4
PROG
Plug into
120 VAC
outlet
not
controlled
by
switch.
Programmer Header J8
Use DMP Model 330 Harness
U11
Z7 GND
ZONE 9
J8
ZONE 7
Secondary Power
Supply
1.2 Amps max. charging
current. Use only 12 VDC
rechargable batteries.
DMP Model 367. Replace
every 3 - 5 years.
Front Tamper
ZONE 8
Model 324
ZONE 6
Class 2 plug-in
Wiring on
terminals 5
through 17
must exit to
the right and
maintain a 1/
4" separation
from the AC
and battery
positive wiring.
Z8
ZONE 10
RJ Cable Monitor J7
Use DMP Model 306 Harness
J7
AC wiring must be in conduit and
exit
J4
out the left side of the panel
RJ SUP
enclosure
Phone Jack Connector
Model 321
16.5 VAC 40VA
Class
2 plug-in
16.5 VAC
20VA
1.5 Amps max. w/ 40
VA
600mA w/ 20 VA
J11DMP Model 300 Harness.
Use
1
2
3
4
J16
Command Processor Reset
Rear Tamper
Z9
Z10+ Z10-
Tamper protection
when required for
Model 350A Attack
Resistant Enclosure.
2-wire
smoke
detector
1K Ω
Zone 10 compatibility
identifier: A
Heat detectors, manual pull
stations, or any other shorting
device. Unlimited number of
units.
Maximum operating range:
8.8 VDC - 14.2 VDC.
See the XR6/XR10 Installation
Guide (LT-0229) for a list of
approved 2-wire smoke detectors.
3.3k Ω
DMP Model 309
ZONE EXPANDER
Keypads
ZONE EXPANDER
Model 714
Model 715
15mA @ 12 VDC
15mA @ 12 VDC
Models 670, 770, 771
Models 714-8, 714-16
100mA @ 8 - 16 VDC
20mA @ 12 VDC
Models 715-8, 715-16
XR6 only
20mA @ 12 VDC
125mA with display lit
STAY
POWER
INSTANT
1
2
3
4
5
6
7
8
9
10
STAY
1
ABC
Model 692
5
75mA @ 8 -16 VDC
9
MNO
INSTANT
2
DEF
6
PQR
0
BYPASS
CODE
3
4
G H I
7
JKL
8
STU
VWX
SPECIAL
COMMAND
Z3 GND Z4 Z5
Z6+ Z6ZONE 6
ARMED
TRBL
ZONE 5
100mA @ 8 - 16 VDC
READY
ZONE 4
Models 690, 790,
791, 793
2-wire
smoke
detector
YZ
Detail for XR6 only
Figure 1: XR6/XR10 Wiring Diagram
Digital Monitoring Products
4
XR6/XR10 Installation Guide
INSTALLATION
Installation
4.1
Mounting the Enclosure
The metal enclosure must be mounted in a secure, dry place to protect the panel from damage due to tampering or the
elements. It is not necessary to remove the PCB when installing the enclosure. The PCB may be installed in the standard
340 enclosure, or the optional 349 enclosure, or the optional 350A Grade A enclosure.
Dual 1/2" and 3/4" Conduit Knockout
Dual 1/2" and 3/4" Conduit Knockout
J11
J16
J11
J16 Processor Reset
Command
Command Processor Reset
1
2
3
4
1
2
3
4
J4
J4
Phone Jack Connector
Phone Jack Connector
U11
EPROM Socket
EPROM Socket
U11
1
2
AC
1
2
AC
AC
3
+B
3
AC
5
4
+B
5
4
-B
6
7
8
BELL GND RED
-B
6
7
8
BELL GND RED
9
YEL GRN
9
10
YEL GRN
10
11
BLK SMK
11
12
BLK SMK
12
13
Z1
GND
13
Z1
Z2
16
15
Z3
16
15
14
GND
14
Z2
GND
Z3
18
17
GND
17
18
Z4
Z5
Z4
19
GND
20
19
Z5
GND
20
Z6
22
21
Z6
22
21
Z7
GND
Z7
23
Z8
23
GND
25
24
Z8
25
24
Z9
26
Z10+ Z10-
Z9
26
Z10+ Z10-
Enclosure Mounting Holes
Enclosure Mounting Holes
Battery shelf
Battery shelf
Figure 2: XR6/XR10 in standard 340 enclosure
Accessory Module
Accessory
Module
Mounting Holes
Mounting Holes
Accessory Module
Accessory Module
Mounting Holes
Mounting Holes
Dual 1/2" and 3/4" Conduit Knockouts
Dual 1/2" and 3/4" Conduit Knockouts
T amper Switch
T amper Switch
Mounting Holes
Mounting Holes
Enclosure Mounting Holes
Enclosure Mounting Holes
J1 1
J 1 11
J16
J16
Reset Jumper
Reset Jumper
2 1
3 2
4 3
4
J4
J4
Phone Jack Connector
Phone Jack Connector
EPROM Socket
EPROM Socket
U1 1
U1 1
1
2
3
4
5
6
7
8
9
10
11
12 13
14
15
16
17
18
19
20
21
22
23
24
25
26
AC 1 AC 2 +B 3 -B 4 BELL5 GND6 RED7 YEL8 GRN9 BLK10 SMK11 Z1 12GND13 Z2 14 Z3 15 GND16 Z4 17 Z5 18 GND19 Z6 20 Z 7 21 GND22 Z 823 Z 924 Z10+25Z10- 26
AC
AC
+B
-B BELL GND RED YEL GRN BLK SMK Z1 GND Z2
Z3 GND
Z4 Z5
GND Z6 Z 7
GND Z 8
Z9
Z10+ Z10-
Enclosure Mounting Holes
Enclosure Mounting Holes
Battery Shelf
Battery Shelf
Dual 1/2" and 3/4" Conduit Knockouts
Dual 1/2" and 3/4" Conduit Knockouts
Figure 2A: XR6/XR10 in optional 349 Enclosure
XR6/XR10 Installation Guide
Digital Monitoring Products
5
INSTALLATION
4.2
Mounting Keypads
Security Command keypads have removable covers that allow you to easily mount the base to a wall or other flat
surface using the screw holes provided on each corner.
For mounting keypads on solid walls, or for applications where conduit is required, use a DMP 695, 696, 775, or 776
keypad conduit backbox.
4.3
Wiring Keypads
The keypad data bus consists of a 4-wire cable that provides 12 VDC power, data in, data out, and a panel common.
You can connect keypads in parallel on one 4-wire cable or provide a separate cable run back to the panel for each
keypad.
Three factors determine the performance characteristics of the keypad bus: the length of wire used, the number of
devices connected, and the voltage at each device. You can connect devices in parallel on the same cable, or provide
separate runs back to the panel.
When planning a keypad bus installation, keep in mind the following four specifications:
1. You can install individual keypads on wire runs of up to 500 feet using 22 gauge wire or up to 1,000 feet using 18
gauge wire. To increase the wire length or add additional devices, a power supply is required.
2. Maximum distance for any one keypad bus/LX-Bus circuit is 2,500 feet regardless of the gauge of wire. This
distance can be in the form of one long wire run or multiple branches totaling no more than 2,500 feet.
3. Maximum number of devices per 2,500 feet circuit is 40. (Note: The XR6 and XR10 panels allow 4 (four)
supervised keypads. Additional keypads can be added in the unsupervised mode.)
4. Maximum voltage drop between the panel (or auxiliary power supply) and any device is 2.0 VDC. If the voltage at
any device is less than the required level, an auxiliary power supply must be added at the end of the circuit. The
2.0 VDC drop maximum has not been verified by UL.
Note: To troubleshoot voltage drop, read the voltage of the last device on the keypad bus.
Refer to the 710 Bus Splitter/Repeater Installation Sheet, LT-0310 (Document No. 0310 on DMP Fax) for
information concerning keypad wiring distances and capacities.
Primary Power Supply
5.1
AC Terminals 1 and 2
Connect the transformer wires to terminals 1 and 2 on the panel. Use no more than 70 ft. of 16 gauge, or 40 ft. of 18
gauge, wire between the transformer and the panel.
Always ground the panel before applying power to any devices: The panel must be properly grounded before
connecting any devices or applying power to the panel. Proper grounding protects against Electrostatic Discharge (ESD)
that can damage system components. See Earth ground, in the Secondary Power Supply section.
5.2
Transformer Types
The larger transformer for the panel is 16.5 VAC 40VA, which provides up to 1.5 Amps of bell output current, 500mA of
auxiliary current, and 100mA of smoke detector output. You can use either the Model 320 wire-in or 321 plug-in
transformer with the panel. The total current available is limited by the total battery standby requirements of the
installation. When the DMP Model 324 16.5 VAC 20VA plug-in transformer is used, the bell output current is reduced to
600mA.
The transformer must be connected to a 120 VAC 60 Hz commercial power outlet that is not controlled by a wall switch.
Never share the transformer output with any other equipment.
Digital Monitoring Products
6
XR6/XR10 Installation Guide
INSTALLATION
Secondary Power Supply
6.1
Battery Terminals 3 and 4
Connect the black battery lead to terminal 4 on the panel and to the negative terminal of the battery. The negative
terminal connects to the enclosure ground internally through the panel circuit board. Connect the red battery lead to
terminal 3 on the panel and to the positive terminal of the battery. Observe polarity when connecting the battery.
The panel can charge up to two batteries.
Use sealed lead-acid batteries only: Use the DMP Model 367, 12 VDC 7.0Ah sealed lead-acid rechargeable battery.
Batteries supplied by DMP or manufactured by Eagle Picher or Yuasa have been tested to ensure proper charging with
DMP products.
GEL CELL BATTERIES CANNOT BE USED WITH THE XR6/XR10 PANEL.
6.2
Earth Ground
Terminal 4 of the panel must be connected to earth ground using 14 gauge or larger wire to provide proper transient
suppression. DMP recommends connecting to a metal cold water pipe or ground rod only. Do not connect to electrical
conduit or a telephone company ground.
6.3
Replacement Period
DMP recommends the battery be replaced every 3 to 5 years under normal use.
6.4
Discharge/Recharge
The panel battery charging circuit float charges at 13.9 VDC at a maximum current of 1.2 Amps using a 40VA
transformer. The total current available is reduced by the combined auxiliary current draw from terminals 7, 11, and
25. The various battery voltage levels are listed below:
Battery Trouble:
Battery Restored:
6.5
Below 11.9 VDC
Above 12.6 VDC
Battery Supervision
The panel tests the battery once every hour when AC power is present. The test lasts for five seconds. A load is placed
on the battery and if its voltage falls below 11.9 VDC a low battery is detected. If AC power has failed, a low battery is
detected any time the battery voltage falls below 11.9 VDC.
If a low battery is detected with AC power present, the test is repeated every two minutes until the battery charges
above 12.6 VDC; the battery restored voltage. If a faulty battery is replaced with a fully charged battery, the restored
battery will not be detected until the next two minute test is done.
6.6
XR6/XR10 Power Requirements
During AC power failure, the panel and all auxiliary devices connected draw their power from the battery. All devices
must be taken into consideration when calculating the battery standby capacity. On the following page is a list of the
power requirements of the panel. Add the additional current draw of Security Command keypads, smoke detector
output, and any other auxiliary devices used in the system for the total current required. The total is then multiplied by
the total number of standby hours required to arrive at the total Ampere/hours required.
XR6/XR10 Installation Guide
Digital Monitoring Products
7
INSTALLATION
6.7 XR6/XR10 Standby Battery Calculations
Standby Current
Command Processor Panel
Active Zones 1-9
50mA ______ mA
1.6mA ______ mA Qty _____ x
Qty _____ x
.1mA ______ mA Qty _____ x
*2mA ______ mA
4mA ______ mA
Bell Output
30mA ______ mA
.1mA ______ mA
1500mA max. ______ mA
770 and 771 Keypads
Active Zones (EOL installed)
Annunciator
50mA ______ mA
Qty _____ x
Active Zone 10 (zone 6 on XR6)
2-Wire Smoke Detectors
Alarm Current
Qty _____ x
100mA ______ mA Qty _____ x 100mA ______ mA
Qty _____ x
1.6mA ______ mA Qty _____ x
*2mA ______ mA
Qty _____ x
20mA ______ mA
(ON)
690, 790, 791, and 793 Keypads
Qty _____ x
100mA ______ mA Qty _____ x 100mA ______ mA
Qty _____ x
1.6mA ______ mA Qty _____ x
*2mA ______ mA
692 Keypads
Qty _____ x
30mA ______ mA Qty _____ x
70mA ______ mA
710 Bus Splitter/Repeater
Qty _____ x
30mA ______ mA Qty _____ x
30mA ______ mA
711 or 714 Zone Expander
Qty _____ x
7mA ______ mA Qty _____ x
7mA ______ mA
Qty _____ x
1.6mA ______ mA Qty _____ x
*2mA ______ mA
Qty _____ x
7mA ______ mA Qty _____ x
7mA ______ mA
Active Zones (EOL installed)
Qty _____ x
4mA ______ mA Qty _____ x
30mA ______ mA
2-Wire Smokes
Qty _____ x
.1mA ______ mA Qty _____ x
.1mA ______ mA
20mA ______ mA
20mA ______ mA
Active Zones (EOL installed)
Active Zones (EOL installed)
715 Zone Expander
714-8 or 714-16 Point Zone Expanders
Active Zones (EOL installed)
Qty _____ x
715-8 or 715-16 Point Zone Expanders
1.6mA ______ mA Qty _____ x
*2mA ______ mA
20mA ______ mA
20mA ______ mA
Active Zones (EOL installed)
Qty _____ x
4mA ______ mA Qty _____ x
30mA ______ mA
2-Wire Smokes
Qty _____ x
.1mA ______ mA Qty _____ x
.1mA ______ mA
30mA ______ mA
30mA ______ mA
Qty _____ x
1.6mA ______ mA Qty _____ x
733 Wiegand Interface
Active Zones (EOL installed)
*2mA ______ mA
Annunciator (ON)
738A Ademco Wireless Interface
20mA ______ mA
75mA ______ mA
75mA ______ mA
50mA ______ mA
50mA ______ mA
______ mA
______ mA
w/Receiver
FA426 16 Point Receiver
Auxiliary Powered Devices on
Terminals 7 and 11
(Other than keypads)
Total Standby ___________ mA
Total Alarm ____________ mA
Total Standby ____________ mA x number of standby hours needed ______ = ___________ mA/hours
Total Alarm + ___________ mA/hours
Total
* Based on 10% of active zones
in alarm condition
Digital Monitoring Products
8
___________ mA/hours
x _.001_____
= ___________ A/hours required
XR6/XR10 Installation Guide
INSTALLATION
Bell Output
7.1
Terminals 5 and 6
Nominal 12 VDC is supplied by terminal 5 on the panel to power alarm bells or horns. The output is rated for a
maximum of 1.5 Amps with a 40VA transformer and 600mA with a 20VA transformer. This output can be steady, pulsed,
or Temporal Code 3 depending upon the Bell Action specified in Output Options programming. Terminal 6 is the ground
reference for the bell circuit.
Keypad Data Bus
8.1
Description
Terminals 7, 8, 9, and 10 of the panel are designated as the keypad data bus. In addition to keypads, the XR6 allows
the connection of four zones on address one: zone expanders, 5845LX Glassbreak Detectors, 6155LX PIRs, and DS775LX
PIRs.
8.2
Terminal 7 - RED
Nominal 12 VDC is supplied at terminal 7 to power Security Command keypads and zone expanders. This is also where
power for any auxiliary device is supplied. The ground reference for terminal 7 is terminal 10. The maximum output is
rated at 500mA. All auxiliary devices totaled together must not exceed the panel's maximum current rating of 500mA.
8.3
Terminal 8 - YELLOW
Data receive from keypads and zone expanders.
8.4
Terminal 9 - GREEN
Data transmit to keypads and zone expanders.
8.5
Terminal 10 - BLACK
Terminal 10 is the ground reference for Security Command keypads, zone expanders, and any auxiliary devices being
powered by terminals 7 and 11.
8.6
Programming Connection
A locking four pin header (J8) is provided to connect a keypad when using a DMP Model 330 Programming Cable. This
provides a quick and easy connection for programming the panel.
Smoke and Glassbreak Detector Output
9.1
Terminal 11
Nominal 12 VDC at 100mA maximum (shared by terminal 25) is supplied at terminal 11 to power 4-wire smoke detectors
or other auxiliary powered devices. This output can be turned off by the user for 5 seconds using the Sensor Reset
Menu Option. Terminal 10 is the ground reference for terminal 11.
XR6/XR10 Installation Guide
Digital Monitoring Products
9
INSTALLATION
Burglary Zones
10.1 Description
The XR10 terminals 12 to 24 are the nine burglary zones. For programming purposes, the zone numbers are 1 to 9. The
zone configurations on terminals 12 to 24 are described below. The XR6 terminals 12 to 18 are the five burglary zones
with terminal 16 providing the ground for zone 5.
Terminal
Function
Terminal
Function
12
Zone 1 voltage sensing
19
Ground for zones 5 & 6
13
Ground for zones 1 & 2
20
Zone 6 voltage sensing
14
Zone 2 voltage sensing
21
Zone 7 voltage sensing
15
Zone 3 voltage sensing
22
Ground for zones 7, 8, & 9
16
Ground for zones 3 & 4 (5 on XR6)
23
Zone 8 voltage sensing
17
Zone 4 voltage sensing
24
Zone 9 voltage sensing
18
Zone 5 voltage sensing
The voltage sensing terminal measures the voltage flowing through the 1k W End Of Line resistor to the zone's ground
terminal. Dry contact sensing devices can be used in series (normally-closed) or in parallel (normally-open) with any of
the burglary protection zones.
10.2 Operational parameters
Each burglary protection zone detects three conditions: open, normal, and short.
The parameters for each are listed below:
Condition
Open
Normal
Short
Resistance on zone
over 1300 ohms
600 to 1300 ohms
under 600 ohms
1K Ohm
Normally
Closed
1K Ohm
Normally Open
Voltage on right terminal
over 2.0 VDC
1.2 to 2.0 VDC
under 1.2 VDC
1K Ohm
Combination Normally Open
and Normally Closed
Figure 3: Protection zone contact wiring
10.3 Zone Response Time
A condition must be present on a zone for 500 milliseconds before it's detected by the panel. Ensure detection devices
used on the protection zones are rated for use with this delay.
10.4 Keyswitch Arming Zone
You can use a momentary keyswitch on a zone programmed as an Arming type for use in arming and disarming the
system without a code.
Digital Monitoring Products
10
XR6/XR10 Installation Guide
INSTALLATION
Powered Zone for 2-Wire Smoke Detectors
11.1 Terminals 25 and 26
A resettable 2-wire Class B powered zone is provided on terminals 25 (positive) and 26 (negative) of the panel. For
programming purposes, the zone number is 10 on the XR10 and zone 6 on the XR6. The zone uses a Model 309, 3.3k
Ohm EOL resistor (provided with the panel) and has an operating range of 8.8 to 14.2 VDC.
Power is dropped from zone 10 any time a Sensor Reset is performed on the panel. Whenever non-Fire and nonSupervisory zone types are used on zone 10, make the appropriate adjustments to the zone's Armed Action to prevent
false alarms from occurring.
The UL compatibility identifier is: A.
Manufacturer
Model
Detector ID
Base
Base ID
# of
Detectors
XR
Panel
Zone Expander
Detection Systems
DS282
B
None
N/A
10
10/20
715, 715-8, 715-16
Detection Systems
DS282TH
B
None
N/A
10
10/20
715, 715-8, 715-16
Detection Systems
DS250
B
MB2W
A
10
10/20
715, 715-8, 715-16
Detection Systems
DS250TH
B
MB2W/MB2WL
A
10
10/20
715, 715-8, 715-16
Detection Systems
DS250HD
B
MB2W/MB2WL
A
10
10/20
715, 715-8, 715-16
DMP/Hochiki
SLK-835
HD-5
HSB-200, HSB-200N
HB-55
7
6/10/20
715, 715-8, 715-16
DMP/Hochiki
SLR-835
HD-3
NS6-100
HB-55
7
6/10/20
715, 715-8, 715-16
DMP/Hochiki
SLR-835B
HD-6
None
N/A
7
6/10/20
715, 715-8, 715-16
Sentrol/ESL
429AT
S09A
None
N/A
12
10/20
715, 715-8, 715-16
Sentrol/ESL
521B
S09A
None
N/A
12
10/20
715, 715-8, 715-16
Sentrol/ESL
521BXT
S09A
None
N/A
12
10/20
715, 715-8, 715-16
System Sensor
1100
STD
None
N/A
10
20
715
System Sensor
1151
STD
B110LP
N/A
10
20
715
System Sensor
1400
STD
None
N/A
10
10/20
715
System Sensor
1451
STD
B401, B401B
N/A
10
10/20
715
System Sensor
2100
STD
None
N/A
10
10/20
715
System Sensor
2400
STD
None
N/A
10
10/20
715
System Sensor
2451
STD
B401, B401B, DH400
N/A
10
10/20
715
System Sensor
1451DH
STD
DH400
N/A
10
10/20
715
System Sensor
2100T
STD
None
N/A
10
10/20
715
System Sensor
2400AT
STD
None
N/A
10
10/20
715
System Sensor
2400AIT
STD
None
N/A
10
10/20
715
System Sensor
2400TH
STD
None
N/A
10
10/20
715
System Sensor
2451TH
STD
B401, B401B
N/A
10
10/20
715
Figure 4: Compatible 2-Wire Smoke Detectors
XR6/XR10 Installation Guide
Digital Monitoring Products
11
INSTALLATION
Annunciator Outputs
12.1 Description
The four annunciator outputs can be programmed to indicate the activity of the panel's zones or conditions occurring on
the system. Annunciator outputs do not provide a voltage but instead switch to ground voltage from another
source. The outputs can respond to any of the conditions listed below:
1)
2)
3)
4)
5)
6)
Activation by zone condition: Steady, Pulse, Momentary, or Follower
Manually from the Security Command keypad
Communication failure
Armed area annunciation
Fire Alarm or Fire Trouble
Ambush alarm
7)
8)
9)
10)
11)
Exit and Entry timers
System Ready
Ground start activation
Cellular Backup
Late to Close
12.2 Harness Wiring
The open collector outputs are accessible by installing the DMP 300 Harness on the 4-pin header labeled J11. The output
locations are shown below. For UL applications, devices connected to the outputs must be located within the same room
as the panel.
Output
1
2
Color
Red
Yellow
Wire
1
2
Output
3
4
Color
Green
Black
Wire
3
4
12.3 Model 860 Relay Module
You may connect a Model 860 Relay Module to the panel to provide relays for the annunciator outputs. These relays can
be used for electrical isolation between the alarm panel and other systems or for switching voltage to control various
functions. The module includes one relay and provides three additional sockets for expansion of up to four relays. A 4wire harness is also provided that connects the Model 860 to the DMP panel.
The 860 mounts inside the panel enclosure using the 3-hole mounting configuration. Plastic standoffs are provided with
the module for ease of installation. Power is supplied to the relay coils from the panel's keypad bus.
Relay Contact Rating: 2 Amps @ 30 VDC
Telephone RJ Connector
13.1 Description
Connect the panel to the public telephone network by installing a DMP 356 RJ Cable between the panel's J4 connector
and the RJ31X or RJ38X phone jack.
Phone Cable Monitor
A two pin header labeled RJ SUP (J7) is provided to allow monitoring of the telephone cable connected between the
panel and a RJ38X jack (pins 2 & 7 jumpered). Attach a DMP Model 306 Harness between J7 and any available zone.
The pins of J7 are connected via the telephone cable to 2 & 7 of the RJ38X jack. The RJ38X jack provides a jumper
between pins 2 & 7 which completes the circuit.
When the zone is programmed for a Supervisory type (SV) and the telephone cable is removed, the keypad will display
the zone in trouble and produce a steady tone.
Digital Monitoring Products
12
XR6/XR10 Installation Guide
INSTALLATION
13.2 FCC Registration
The panel complies with FCC part 68 and is registered with the FCC.
Registration number: CCKUSA - 18660 - AL - R
Ringer Equivalence: 1.1B
13.3 Notification
Registered terminal equipment must not be repaired by the user. In case of trouble, the device must be immediately
unplugged from the telephone jack. The factory warranty provides for repairs. Registered terminal equipment may not
be used on party lines or in connection with coin telephones. Notification must be given to the telephone company with
the following information:
a. The particular line(s) the service is connected to
b. The FCC registration number
c. The ringer equivalence
d. The make, model, and serial number of the device
13.4 Ground Start
To configure the panel for ground start operation, you must install the appropriate ground start module and program
one of the panel's available annunciator outputs for Ground Start operation. Refer to the panel Programming Guide for
complete programming information. This option must not be selected on a UL listed system.
Reset Jumpers J16
14.1 Description
There are two reset jumpers located at the top right of the panel's circuit board labeled RESET. Momentarily shorting
these jumpers allows you to reset the microprocessor. Resetting the panel allows you to enter the panel's internal
programmer.
To reset the panel when first installing the system, place the blade of a slotted screwdriver across the two reset
jumpers after applying power to the panel.
To reset the panel while the system is operational (for example, prior to reprogramming), you can short the jumpers
without powering down the system.
After resetting the panel for programming, you must begin within 30 minutes. If you wait longer than 30 minutes, you
will have to reset the panel again.
XR6/XR10 Installation Guide
Digital Monitoring Products
13
COMPLIANCE
UNIVERSAL UL BURGLARY SPECIFICATIONS
15.1 Introduction
The programming and installation specifications contained in this section must be completed when installing the XR6/
XR10 in accordance with any of the UL burglary standards. Additional specifications may be required by a particular
standard.
15.2 Wiring
All wiring must be in accordance with NEC, ANSI/NFPA 70, UL 681, and UL 611 for all burglary installations.
15.3 Police station phone numbers
The digital dialer telephone number programmed for communication must not be a police station phone number, unless
that phone number is specifically provided for that purpose.
15.4 Bypass reports
The bypass reports option must be programmed as YES for all UL burglary applications. See the XR6/XR10 Programming
Guide (LT-0230).
15.5 System maintenance
Proper installation and regular maintenance by the installing alarm company and frequent testing by the end user is
essential to ensure continuous satisfactory operation of any alarm system. Offering a maintenance program and
acquainting the user with the correct procedure for use and testing of the system is also the responsibility of the
installing alarm company.
15.6 Cross zoning
Zones used for cross zoning must be installed to allow detection of the same event. Cross zoning shall not conflict with
UL 681 or 1641.
15.7 Ground Start
Ground Start phone lines must not be used for UL listed systems.
15.8 UL Listed Receivers
UL has verified operation with the DMP SCS-1 Security Receiver, Sur-Gard SG-HLR2-DG, FBII CP220PB, OsborneHoffman Quick-Alert and Radionics D6500 receivers.
UL 1023 SPECIFICATIONS
Household Burglar-Alarm System Units
16.1 Bell cutoff
The bell cutoff time cannot be less than five minutes. See the XR6/XR10 Programming Guide (LT-0230).
16.2 Entry delay
The maximum entry delay used must not be more than 45 seconds. See the XR6/XR10 Programming Guide (LT-0230).
16.3 Exit delay
The maximum exit delay used must not be more than 60 seconds. See the XR6/XR10 Programming Guide (LT-0230).
16.4 Zone expansion on 4-wire bus
When expansion zones are used, the keypad and zone
expander 4-wire bus must be limited to 3 feet in length
unless an external communication fail indicator is added. A
12 VDC relay may be wired as a communication fail indicator.
To install, connect the negative side of the indicator to one
of the panel's annunciator outputs and the positive side to
the smoke power (terminal 11 of the panel). See the XR6/
XR10 Programming Guide (LT-0230).
Normally Closed
Voltage output
from terminal 11
+
Zone activated
annunciator output
Ð
Voltage output
from terminal 11
+
Zone activated
annunciator output
Ð
Common
Normally Open
1k Ohm
Device Fail LED
In addition to the wiring described above, a 24-hour zone
must be programmed to activate the appropriate annunciator output.
Digital Monitoring Products
14
XR6/XR10 Installation Guide
COMPLIANCE
UL 1610 and 1076 SPECIFICATIONS
Central-Station and Proprietary Burglar-Alarm Units
17.1 Opening/Closing reports
The Opening/Closing Reports option must be programmed as YES. See the XR6/XR10 Programming Guide (LT-0230).
17.2 Automatic bell test
This option must be programmed as YES. See the XR6/XR10 Programming Guide (LT-0230).
17.3 Proprietary dialer
The Model XR6/XR10 provides Grade A proprietary service when configured as a digital dialer.
UL 1635 SPECIFICATIONS
Digital Burglar Alarm Communicator System Units
18.1 Digital Dialer telephone number
Both programmed telephone numbers must begin with a D or P. See the XR6/XR10 Programming Guide (LT-0230).
18.2 Entry delay
The maximum entry delay used must not be more than 60 seconds. See the XR6/XR10 Programming Guide (LT-0230).
18.3 Exit delay
The maximum exit delay used must not be more than 60 seconds. See the XR6/XR10 Programming Guide (LT-0230).
18.4 Test frequency
The Test Frequency option must be programmed so that the panel sends a report once every 24 hours. See the XR6/
XR10 Programming Guide (LT-0230).
18.5 Automatic bell test
This option must be programmed as YES. See the XR6/XR10 Programming Guide (LT-0230).
18.6 Grade B Central Station
Grade B Central Station service can be provided under UL 1635 by adding a Grade A local audible signal appliance and
placing the Model XR6/XR10 panel into the Model 350A Grade A Attack Resistant Housing.
XR6/XR10 Installation Guide
Digital Monitoring Products
15
COMPLIANCE
UL 365 and 609 SPECIFICATIONS
Police Station Connected and Local Burglar Alarm Units
and Systems
19.1 Entry delay
The maximum entry delay used must not be more than 60 seconds when using the Model 349A Grade A housing. See the
XR6/XR10 Programming Guide (LT-0230).
19.2 Grade A bell
A Grade A local audible signal appliance must be used.
19.3 Bell cutoff
The bell cutoff time cannot be less than 15 minutes. See the XR6/XR10 Programming Guide (LT-0230).
19.4 Automatic bell test
The Automatic Bell Test option must be programmed as YES. See the XR6/XR10 Programming Guide (LT-0230).
19.5 Grade A Mercantile
For Grade A Mercantile and Police Station Connect operation the Model XR6/XR10 must be mounted in a Grade A attack
resistant housing, (DMP Model 350A).
19.6 Mercantile Safe and Vault
When the DMP Model 350A housing is used, the panel provides operation as a mercantile safe and vault alarm. Bell
Supervision and wiring must be in accordance with UL 681. If the panel is mounted outside the safe or vault, tamper
protection and the Sentrol Model 5402 or Potter EVD listed vibration detectors should be used. The XR6/XR10 does not
provide operation as a Bank Safe and vault alarm.
19.7 Line security for Police Connect
Basic line security is provided when the Model XR6/XR10 is configured as a dialer system.
Digital Monitoring Products
16
XR6/XR10 Installation Guide
COMPLIANCE
UNIVERSAL UL and NFPA FIRE ALARM SPECIFICATIONS
20.1 Introduction
The programming and installation specifications contained in this section must be completed when installing the Model
XR6/XR10 in accordance with any of the UL or NFPA fire standards. Additional specifications may be required by a
particular standard.
20.2 Wiring
All wiring must be in accordance with NEC, ANSI/NFPA 70.
20.3 Police station phone number
The digital dialer telephone number programmed for communication must not be a police station phone number, unless
that phone number is specifically provided for that purpose.
20.4 System maintenance
Proper installation and regular maintenance by the installing alarm company and frequent testing by the end user is
essential to ensure continuous satisfactory operation of any alarm system. Offering a maintenance program and
acquainting the user with the correct procedure for use and testing of the system is also the responsibility of the
installing alarm company.
20.5 Audible alarm
Fire Type zones should be programmed to activate an audible alarm. The Bell Action for Fire Type zones should not be
programmed as “N”. See the XR6/XR10 Programming Guide (LT-0230).
20.6 Fire zone programming
Fire zones must be programmed to activate a trouble on open conditions and an alarm on short conditions. The swinger
bypass function must not be used on any fire zones. See the XR6/XR10 Programming Guide (LT-0230).
20.7 Ground Start
Ground Start phone lines must not be used for UL listed systems.
20.8 UL Listed Receivers
UL has verified operation with the DMP SCS-1 Security Receiver, Sur-Gard SG-HLR2-DG, FBII CP220PB, OsborneHoffman Quick-Alert and Radionics D6500 receivers.
UL 985 NFPA 72 (chapter 2) SPECIFICATIONS
Household Fire Warning System Units
21.1 Bell output definition
The bell output of the Model XR6/XR10 must be programmed to operate steady on burglary alarms and pulsed on fire
alarms. See the XR6/XR10 Programming Guide (LT-0230).
21.2 Indicating Circuit Supervision
The DMP Models 865 and 866 Notification Circuit Module must be used on the bell circuit for detection of shorts and
grounds. See Section 23.1 for wiring diagrams.
CALIFORNIA STATE FIRE MARSHAL SPECIFICATIONS
22.1 Bell output definition
The bell output must be programmed to operate steady on burglary alarms and temporal on fire alarms. See the XR6/
XR10 Programming Guide (LT-0230).
XR6/XR10 Installation Guide
Digital Monitoring Products
17
18
Digital Monitoring Products
1k Ω
Bell T rouble
Bell T rouble
Bell B Ð Output
Bell B + Output
Bell A Ð Output
Bell A + Output -
Bell Power Ð Input
Bell Power + Input
Alarm Input
Ground
Auxiliary Power
10
11
9
7
8
6
5
4
2
3
1
Power Supply
Trouble Contacts
N/C
AUXILIARY
POWER
SUPPLY
8
7
6
5
4
3
2
1
S
S
S
S
S
S
S
26mA at 12 VDC
85mA
at 12865
VDC
DMP
Model
DMP Model 865
S
S
S
S
S
S
12 or 24 VDC
5 Amp Maximum
Notification
Circuit
Module
Notification
Circuit
Module
12 or 24 VDC
5 Amp Maximum
Bell T rouble
Bell T rouble
Bell Output -
Bell Output +
Bell Power Input
Alarm Input
Ground
Auxiliary Power
45mA at 12 VDC
Notification Circuit Module
DMPModel
Model866
866
DMP
37mA at 12 VDC
Notification Circuit Module
Style W
AUXILIARY
POWER
SUPPLY
1
AC
2
AC
Power Supply
Trouble Contacts
N/C
3
+B
-B
4
J4
BELL
5
GND
6
S
RED
7
8
9
GRN
10
S
BLK
11
SMK
12
13
Z1
14
GND
15
Z2
S = Supervised Circuit
GND
16
Z3
J16
S
GND
17
S
Z4
18
Z5
19
GND
20
21
Z6
Command Processor Reset
22
Z7
The Auxiliary Power Supply and Indicating Circuit Module
trouble contact zone must be programmed as a Supervisory
Type zone and must be selected for display in the keypad
status list.
YEL
Phone Jack Connector
NOTE: If an auxiliary supply is not used,
terminals 3 and 4 on the 866 Indicating
Circuit Module can be jumpered together
to supply bell power from the XR20 panel.
A maximum of 1.5 Amps at 12 VDC is
available from terminal 5 of the XR20.
Each 865 Notification Circuit Module
in alarm draws up to 85mA from its
terminal 3 alarm input.
UL Listed, Polarized
Indicating Devices.
Style Z
Each 866 Indicating Circuit Module
in alarm draws up to 35mA from its
terminal 3 alarm input.
UL Listed, Polarized
notification Devices.
10k Ω EOL Resistor
DMP Model 308
23
GND
24
Z8
25
Z9
Z10+
26
Z10-
27
J11
U11
EPROM Socket
Optional Module installation
1
2
3
4
WIRING DIAGRAMS
23.1 Multiple Indicating Circuit Module Installation
XR6/XR10 Installation Guide
RJ31X Telco Jack
MAIN
BACKUP
1 2 3 4 5 6
1
2
3
4
Telephone Connections
J11
Use EOL Termination
Assembly P/N 21024-0003
(590 W 1/2 W Resistor).
S
Panel Auxiliary Power - Terminal 7
Panel Common - Terminal 10
Supervisory Zone Input - Terminal 13
Note 1
Note 1
Note 1: Use EOL Termination
Assembly P/N 21024-0001
(2.2k W 1/2 W Resistor).
10
S
13
S
S = Supervised Circuit
19
Digital Monitoring Products
WIRING DIAGRAMS
7
23.2 Installation for Derived Channel burglary
XR6/XR10 Installation Guide
DCX Systems
STU-2Z
24.1 Troubleshooting
This section of the Installation Guide provides troubleshooting information for use when installing or servicing an XR6/
XR10 system.
Problem
Possible Cause
Solution
J16 reset jumper is installed.
Remove the J16 reset jumper.
Open or short on the green data
wire to the keypad.
Check for broken or shorted wires
between the keypad and panel.
Bad keypad or zone expander.
Replace with a new or repaired
keypad or zone expander.
Keypad display is not functional.
When a key is pressed, only a
short beep is emitted.
Open or short condition on the
yellow data wire.
Check for broken or shorted
wires.
Bad keypad or zone expander.
Replace with a new or repaired
keypad or zone expander.
Keypad beeps when keys are
pressed but won't allow the user
to arm or enter the User Menu.
Two or more keypads are assigned
to the same address.
Security Command keypads
display " SERVICE REQUIRED"
Set each keypad to a different
address to match the Device
Setup programming.
LT-0229 (8/02) © 2002 Digital Monitoring Products, Inc.
800 - 641 - 4282
INTRUSION
•
FIRE
•
ACCESS
•
NETWORKS
www.dmp.com
2500 North Partnership Boulevard
Made in the USA
Springfield, Missouri 65803-8877
Download PDF