MLS 506SA MediaLink™ Switcher

MLS 506SA MediaLink™ Switcher
Control
Connections
MLC/IR
ABC
INPUT 1
VIDEO
R-Y
Y
100-240V
INPUT 2
VIDEO
INPUT 3
R-Y
VIDEO
Y
R-Y
Y
INPUT 4
INPUT 5
INPUT 6
RGB
R
H/
HV
R
H/
HV
R
H/
HV
R
H/
HV
G
V
G
V
G
V
G
V
YUV
VIDEO
R-Y
STEREO AMPLIFIED OUTPUT
S-VIDEO
Y
Switcher
rear panel
MLC/IR port
LEFT
NOTE
The switcher provides
power to the controller.
NOTE
If you use cable that has a
drain wire, tie the drain wire
to ground at both ends.
RIGHT
Y
0.2A 50/60 Hz
B-Y
C
B-Y
C
C
B-Y
B
B
B
B
B-Y
AUX/MIX
EFFECTS
L
R
L
R
L
R
L
R
L
R
L
.5A MAX
R
SEND
L
R
RETURN
L
L
R
C
MLC/IR
AUDIO OUT
FIXED
L
R
VARIABLE
L
R
RS232
A B C
R
CONTACT CLOSURE
MLS 506SA Rear Panel
+12VDC
Ground ( )
+12VDC
Ground ( )
Transmit (Tx) B
Receive (Rx) A
B Receive (Rx)
A Transmit (Tx)
DISPLAY
POWER
VCR
DVD
Laptop
MLS 506SA to an MLC 206
VOLUME
MAX/
MIN
Extron
MLC
MLS/Power
port
MLC 206
MediaLink Controller
A B
MLC 206
MLS / Power
Non-amplified Audio Connections
Balanced
Audio Input
Balanced
Audio Input
Unbalanced
Audio Input
(600 ohms)
(high impedance)
(high impedance)
R
L
L
R
L
R
Tip
Ring
Sleeves
Tip
Ring
STEREO AMPLIFIED OUTPUT
LEFT
RIGHT
2 sec.
2 sec.
INPUT
#2
MENU
Improper impedance matching between the
amplifier and speakers may produce less than
full power output and can cause damage to
the amplifier. Set the output load via the
Audio Settings menu or via RS-232.
MENU
Set audio output level
per input.
NEXT
AUDIO
ADJUST
NEXT
NEXT
#2
Adjust treble
per input.
Adjust bass
per input.
Level
050
#2
Bass
+00dB
#2
Treble
+00dB
• For consumer audio sources [VCRs, laptop computers, etc. that output -20dBV
(0.10Vrms) through-10dBV (0.32Vrms)], set the level between 80 and 94.
MENU
• For professional sources [mixers, signal processors, etc. outputting 0dBu
(0.78Vrms) to +4dBu (1.23Vrms)], set the level between 50 and 65.
• Adjust level, bass, and treble so that the Clip LED does not light.
Set audio
output balance.
AUDIO
SETTINGS
NEXT
NEXT
Balance
––––––––
Enable/disable
Effects Return.
Select Stereo or
Mono audio output.
NEXT
Output
M<Stero>
MENU
NEXT
www.extron.com
Select impedance for
amplified output.
NEXT
Effects
E<Dsabl>
MENU
or timeout
CAUTION
Output impedance
must be set prior to use!
VIDEO
CONFIG
MENU
Stereo amplified
output: 30 watts
per channel into
a 4 ohm or
8 ohm load.
Do NOT short output
terminals to ground.
Doing so will damage
the amplifier.
Stereo Amplified Audio Output
EXTRON
MLS506SA
CAUTION
Connect the sleeve
to ground (Gnd).
Connecting the
sleeve to a negative
(–) terminal will
damage the audio
output circuits.
R
Tip
Sleeve
Tip
Sleeve
Tip
Ring
Sleeve (s)
Tip
Ring
Tip
Ring
Sleeve (s)
Tip
Ring
Unbalanced
Audio Output
Tip
See Caution
Sleeves
See Caution
Ring
L
600 ohms
R
600 ohms
L
Balanced
Audio Output
SpkrLoad
<4ohm> 8
NEXT / MENU
EXIT
MENU
Extron Electronics, USA
Extron Electronics, Europe
Extron Electronics, Asia
Extron Electronics, Japan
1230 South Lewis Street
Anaheim, CA 92805
USA
714.491.1500
Fax 714.491.1517
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax +31.33.453.4050
135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400
Fax +65.6383.4664
Daisan DMJ Building 6F
3-9-1 Kudan Minami
Chiyoda-ku, Tokyo 102-0074 Japan
+81.3.3511.7655
Fax +81.3.3511.7656
33-651-01 Rev. D
04 03
Printed in the USA