Vision Fitness | T9800 Series | T9800 AG7.qxd - Vision Fitness

Water Bottle, Qty: 1
Handlebars, Qty: 2
Handlebar Covers, Qty: 2
Power Cord, Qty: 1
Color-coded Hardware Bags
M5 x 12L Phillips Head
Quantity: 2
M8 x 15L Flat Head
Quantity: 2
M6 x 15L Socket Head
Quantity: 6
6.5x13x1T Arc Washer
Quantity: 2
PARTS BOX
6.5x19x2T Flat Washer
Quantity: 4
PINK BAG
10.2x19x2T Flat Washer
Quantity: 4
8.2x19x2T Flat Washer
Quantity: 8
M10 x 20L Bolt
Quantity: 4
M8 x 15L Socket Head
Quantity: 8
8.2x19x2T Flat Washer
Quantity: 4
M8 x 15L Socket Head
Quantity: 4
Screwdriver
5mm L-Shaped Wrench
6mm L-Shaped Wrench
ORANGE BAG
BLUE BAG
8mm T-Shaped Wrench
HARDWARE INCLUDED
5
TOOLS, HARDWARE, & PARTS INCLUDED
STEP
AUTO-CALIBRATION
DO NOT STAND ON THE BELT WHEN PERFORMING AUTO-CALIBRATION
You need to access User Engineering Mode to run the auto-calibration. With the safety key in place , please hold
down SPEED DOWN and ENTER for 5 seconds. When in the User mode, “USER ENG MODE” appears in the
alphanumeric window. To access the data press the ELEVATION keys until “AUTO-CALIBRATION” appears.
To begin auto-calibration, press ENTER. The treadmill will run through minimum and maximum speed and
maximum incline. This will take 3-5 minutes. Let the treadmill perform this complete function before exiting the
Engineering Mode.
Elevation A/D appears in the left window. PWM value appears in the dot matrix window, and speed appears in
the right window. “CALIBRATION PASSED” will appear in the alphanumeric window when the auto-calibration is
complete. The treadmill will come to a complete stop and return to the start-up screen in the alphanumeric window.
Assembly
Guide
500 South CP Avenue • P.O. Box 280 • Lake Mills, WI 53551
toll free 800.335.4348 • phone 920.648.4090 • fax 920.648.3373
www.visionfitness.com
©2007 Vision Fitness. All Rights Reserved. 5.07
AG18.39PRD
REV7
T9800 Series
TREADMILLS
Water Bottle, Qty: 1
Handlebars, Qty: 2
Handlebar Covers, Qty: 2
Power Cord, Qty: 1
Color-coded Hardware Bags
M5 x 12L Phillips Head
Quantity: 2
M8 x 15L Flat Head
Quantity: 2
M6 x 15L Socket Head
Quantity: 6
6.5x13x1T Arc Washer
Quantity: 2
PARTS BOX
6.5x19x2T Flat Washer
Quantity: 4
PINK BAG
5mm L-Shaped Wrench
M8 x 15L Socket Head
Quantity: 8
M10 x 20L Bolt
Quantity: 4
8.2x19x2T Flat Washer
Quantity: 8
10.2x19x2T Flat Washer
Quantity: 4
8.2x19x2T Flat Washer
Quantity: 4
M8 x 15L Socket Head
Quantity: 4
Screwdriver
6mm L-Shaped Wrench
ORANGE BAG
BLUE BAG
8mm T-Shaped Wrench
HARDWARE INCLUDED
STEP
5
TOOLS, HARDWARE, & PARTS INCLUDED
AUTO-CALIBRATION
DO NOT STAND ON THE BELT WHEN PERFORMING AUTO-CALIBRATION
You need to access User Engineering Mode to run the auto-calibration. With the safety key in place , please hold
down SPEED DOWN and ENTER for 5 seconds. When in the User mode, “USER ENG MODE” appears in the
alphanumeric window. To access the data press the ELEVATION keys until “AUTO-CALIBRATION” appears.
To begin auto-calibration, press ENTER. The treadmill will run through minimum and maximum speed and
maximum incline. This will take 3-5 minutes. Let the treadmill perform this complete function before exiting the
Engineering Mode.
Elevation A/D appears in the left window. PWM value appears in the dot matrix window, and speed appears in
the right window. “CALIBRATION PASSED” will appear in the alphanumeric window when the auto-calibration is
complete. The treadmill will come to a complete stop and return to the start-up screen in the alphanumeric window.
Assembly
Guide
500 South CP Avenue • P.O. Box 280 • Lake Mills, WI 53551
T9800 Series
toll free 800.335.4348 • phone 920.648.4090 • fax 920.648.3373
TREADMILLS
www.visionfitness.com
©2007 Vision Fitness. All Rights Reserved. 5.07
AG18.39PRD
REV7
Assembly
Guide
STEP
3
• Insert the handlebar cover onto the
handlebar. Insert the right handlebar
by holding the handlebar sideways
toward the treadmill and inserting the
top into the console. Rotate the
handlebar into the bracket located on
the console mast. Fasten with a bolt
(M5x12L), and a bolt (M6x15L socket
head) & an arc washer (6.5x13x1T)
into the two holes of the console plastic, and a bolt (M8x15L flat head) into
the hole in the handlebar. Fasten a bolt
(M6x15L socket head) and a flat washer
(6.5x19x2T) into the hole in the handlebar on the console mast. Do not fully
tighten the bolts.
T9800 Series
TREADMILLS
To avoid possible damage to this Platform Treadmill, please follow these assembly steps in the correct
order. Before proceeding though, find your new Platform Treadmill’s 2 serial numbers, located on the
underside of the main frame, and on the bottom of the console, and enter here:
Frame Serial Number
STEP
2
• Slide the handlebar cover over the
bracket and secure with a bolt
(M6x15L socket head) and a flat
washer (6.5x19x2T). Do not fully
tighten the bolt.
Console Serial Number
Refer to these numbers when calling for service, and also enter these serial numbers on your Warranty
Card and in your own records. Be sure to read your Owner’s Guide before using your new Platform Treadmill.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
STEP
3
• Repeat on the left side.
NOTE: It is recommended that you apply grease to the threads of each bolt as you assemble your Platform
• Fully tighten the console and
handlebar bolts.
Treadmill, to prevent loosening and noise. Also, during each assembly step, ensure that ALL nuts and bolts
are in place and partially threaded in before completely tightening any ONE bolt.
STEP
STEP
1
4
MOTOR COVER
TV Power Cable
ORANGE BAG
• Place the motor cover back on the
frame and fasten with 6 screws.
Coaxial Cable
• Remove motor cover screws and
take off the motor cover.
• Insert the right console mast to the
right console mast bracket. First, fasten
the inside of the console mast to the
console mast bracket by securing four
bolts (M8x15L socket head) and four
washers (8.2x19x2T). Fully tighten the
bolts. Second, fasten the two bolts
(M10x20L button head) and two
washers (10.2x19x2T) on the front of
the console mast and fully tighten.
PINK BAG
STEP
• Attach the power cord to the treadmill.
4
• Plug the power cord into the power
outlet.
STEP
TV BRACKET WIRING
5
AUTO-CALIBRATION
Please refer to back cover for this
procedure, then return to Step 6.
• Repeat on the left side
STEP
STEP
2
BLUE BAG
1
STEP
• Take the wire tie off the cables. Plug
the large 20-pin ribbon connector into
the 20-pin connector on the lower
control board. Attach the two grounding
wire connectors to the two grounding
wires located in the motor pan near
the front of the frame. Connect the TV
power cable to the TV power connector
and coaxial cable to the coaxial
cable connector; both located on the
inside of the motor compartment at the
front of the treadmill.
BELT TENSION
• If the running belt slips when used,
run the treadmill at 2.0 mph and use
the supplied 8mm Allen wrench to turn
the left and right tension bolts clockwise
1/4-turn at a time until the belt no
longer slips.
• Tie the ribbon data cable, TV
power cable, and coaxial cable to
the cable wire tie on the top of the
right console mast. Feed the cables
down the console mast and through the
hole at the lower part of the console
mast. Remove protective plastic cover.
Push any remaining cable into the
console mast.
• Mount the console onto the left and
right console masts using four bolts
(M8x15L socket head) and four washers
(8.2x19x2T). Do not fully tighten.
6
STEP
6
• If the running belt is too far to the
right side, run the treadmill at 2.0 mph
and use the supplied 8mm Allen
wrench to turn the right tension bolt
clockwise 1/4-turn at a time until the
belt remains centered during use.
If the running belt is too far to the left
side, run the treadmill at 2.0 mph and
turn the left tension bolt clockwise
1/4-turn at a time until the belt remains
centered during use.
Download PDF

advertising