Reliable | i500 | Instruction manual | Reliable i500 Instruction manual

i500
Professional Iron System
Instruction Manual
USER INSTRUCTIONS
Thank you for purchasing the RELIABLE i500 series iron system. Please
follow the instructions carefully. With proper care and maintenance, your
steamer will provide years of dependable service.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Remove the ironing station from its packing and make sure all packing
parts have been taken off (including the protection bags). Lay the
station on a flat and steady surface fitted to support it next to a wall
socket (max. mt. 1,5).
It is recommended to lay the iron on the supplied pad.
Insert in the right seat (2) the small supplied wand to hold the hose up
and hook it with the spring up to the iron-boiler connecting wire.
Unscrew the safety cap (1) and let the internal air out. Fill the boiler
with: Max. 2,0 litres of water for model i500
Use the funnel supplied, making sure you do not overfill the tank.
Insert the plug into the main supply point; switch on boiler (4) and iron
button (3). If the two buttons come on, iron and boiler are working.
Turn the iron plate’s temperature regulating knob (6) to the position
“cotton °°°” (indicated on the iron knob).
Wait that the boiler button’s red light (4) goes off (it takes about 10
minutes). While ironing, the boiler button’s red light normally comes on.
The machine is ready for use.
Push the steam button (7).
It is possible to regulate the quantity of steam by the steam knob (8).
In case the steam stops during ironing and the water button’s red light
(5) comes on, it means that there is not enough water in the tank. To
start ironing again, switch off the boiler button (4); press the steam iron
button (7) to ensure there is no more steam in the boiler, slowly open
the pressure cap (1) and refill to the required level with warm water.
Replace the cap and wait for it to build up pressure again.
When you first press the steam button (after having turned the boiler
on and depressed the steam button on the iron) you might notice a
decrease in pressure. This is because the tank has air in it. In order to
have plenty of steam (after you have depressed the iron) wait until the
pressure goes back up to the maximum level before you begin.
IMPORTANT
When you are finished using the boiler for the day, unscrew the fill cap oneturn on the unit to release the steam/air from the tank. This will eliminate the
vacuum that may cause damage to the pressure gauge.
COMPONENTS
1.
2.
3.
4.
5.
6.
7.
8.
9.
Safety cap
Wand to hold mono-hose up
Iron button
Boiler button
Light for low water
Temperature regulating knob
Steam button
Steam regulation knob
Manometer
CAUTION
•
•
•
•
Do not leave the machine unattended while the plug is connected to
the socket.
The iron reaches very high temperatures and it keeps being very hot
even 15 minutes after it’s been switching off. Be careful not to burn
yourself.
For complete safety, before filling the boiler, please disconnect the
plug.
While using the machine, never unscrew or remove the cap while
under pressure (1). Before removing it, make sure that it does not
•
•
give off steam anymore by shutting the boiler off, and pressing the
steam iron button (7) to release all remaining steam.
The machine has a special heating element. Only qualified
technician should replace it.
The safety cap (1) must be replaced with original parts only.
TECHNICAL DATA
Adjustable iron thermostat set from 60°C to 200°C
Bimetallic safety iron thermostat with manual reset at 275°C
Full aluminium-plated heating element at 800W – 230V
Boiler power i500: 1000W
Working pressure i500: 3,5 bar
Tank nominal capacity of model i500: 2.5 litres
TROUBLESHOOTING
PROBLEM
Does
steam go
out from
the boiler?
EXPLANATION
It may happen that, while filling the
tank, some water overfills the cap
and flows inside the boiler wetting
the insulating material
SOLUTION
In order to solve the problem, we suggest
using the machine as usual so that the
insulating material dries up in about one
hour through the heat of the machine. In
case you still have this problem after one
working hour, please contact the service
centre.
Does the
1) While filling the tank you may 1) The problem will go on until the excess
steam iron have poured too much water into it. water is emptied. Keep the steam button
leak steam
depressed until the water in the tank is at
mixed with
the correct level.
water?
2) The iron plate has to be hot 2) Please check that the temperature knob
before the steam passage
is on the right position: “cotton °°°)”
There is
1) The steam knob (where
1) Open the steam knob anticlockwise.
no steam
supplied) might be closed
coming out
of the
2) The iron switch might be off
2) After the iron switch comes on, wait for 4
iron?
minutes so that the iron plate gets hot.
3) The boiler switch might be off
3) After the boiler switch comes on, wait for
10 minutes so the boiler produces steam.
4) Fill it following the instructions carefully.
Does the
ironing
board get
wet?
4) The water might be used up.
1) The ironing board cover might
not be able to absorb the steam
completely
2) The steam iron leaks steam
mixed with water (Check by
spraying some steam on a dry
cloth)
1) You might use a thicker cover (or two
covers) so to create a thicker surface to
absorb the steam better. In case you are
using a vacuum table, switch on the
vacuum function each time you are using
the steam
2) See # 2
mixed with water (Check by
spraying some steam on a dry
cloth)
Does the
Some dirty might have gone into Fill the empty tank with 1 liter of water,
steam leak the tank with the water and it is screw the cap up, shake it, unscrew the
dirty
given off from the iron.
cap and empty the tank. Repeat the action
water?
until the water is cleaned. We do not
recommend the use of any additive to pour
in the tank. Before ironing again spray
some steam on a cloth until clean steam
comes out.
SPARE PARTS LISTS
ITEM CODE
Q.TY
DESCRIPTION
CD332
1
HANDLE
CD332/2
1
HEXAGONAL HEADED SCREW FOR HANDLE
CD338/1
1
NUT FOR WAND SUPPORT
CD338/2
1
WASHER FOR STICK SUPPORT
CD338/3
1
WAND SUPPORT
CD339/1
1
TANK
CD343/110
1
COPPER HEATING ELEMENT 1000 W - 120V
CD344
1
SILICONE O-RING FOR THE HEATING ELEMENT
CD346/35
1
PRESSURE SWITCH WITH RESET SET 2,5 BAR
CD347
1
FAIRLEAD FOR CAP CONNECTION
CD347/7000
1
SOLENOID VALVE FAIRLEAD
CD348
1
BULB THERMOSTAT 165°
CD348/1
1
SCREW FOR BULB THERMOSTAT
CD349
1
BIPOLAR SWITCH 16A
CD350/110
1
RED PILOT LIGHT 120V
CD351
1
CONNECTOR
CD353
4
4 POLE TERMINAL BOARD PA 21 TO FASTON
CD360
1
FAIRLEAD STOP 6W-1
CD361
1
FAIRLEAD STOP 6N3
CD365/4
1
MALE SAFETY CAP 3/8 SET 5,5 BAR
CD366/1
1
SAFETY CAP O-RING FOR CD365/4
CD367
1
DYN SMALL FOOT
CD368
1
STICK FOR MONOHOSE
CD369
1
FUNNEL DIAMETER 10 FOR ITEM 013
CD371/110
1
ADJUSTABLE SOLENOID VALVE S/7000 - 120V
CD374
1
GAUGE FOR 06-09/D
CD376
1
MUSHROOM-SHAPED SMALL CAP FOR IRON REST
CD377
1
ANTI-UNSCREWING SCREW 35x5
CD380/110
1
WIRING 120V
CD382
1
CD384
1
CD470
1
GLASS WOOL INSULATING
3 WAY RECEPTACLE 1/4 GAS CONICAL 1/4 FEMALE 1/8
FEMALE
BACK STAINLESS CHASSIS
CD471
1
LOWER STAINLESS CHASSIS
CD473
1
FRONT STAINLESS CHASSIS
CD477
1
STAINLESS UPPER BODY
CV103
1
NUT 1/4 FOR SOLENOID VALVE 7000
GV025/51
1
COPPER PIPE
GV026/7
1
FEMALE QUICK RELEASE
GV028/6
1
"L" JOINT
GV028/30
1
"L" JOINT WITH OGIVA
GV028/31
1
"L" JOINT FOR MANOMETER
GV028/35
1
POWER CORD
GV028/36
1
ILME FEMALE SOCKET GROUP
GV028/45
1
COVER WITH ROD
RIC003/2
1
CERAMIC TERMINAL BOARD 120V
i500 PARTS DRAWING
www.reliablecorporation.com
Download PDF