BUBBLE JET PRINTER
User’s Guide
V1
Table of Contents
Table of Contents
Introduction .....................................................................................................5
How to Use This Manual .................................................................................6
Safety Precautions .........................................................................................8
Printer Parts and Their Functions .................................................................14
Front View ................................................................................................... 15
Rear View .................................................................................................... 16
Inside the Printer ......................................................................................... 17
Operation Panel .......................................................................................... 18
Printer Driver Functions (Windows) ..............................................................19
Opening the Printer Properties Dialog Box ................................................. 20
Printer Properties Dialog Box Description ................................................... 22
BJ Status Monitor Functions ....................................................................... 37
Cancelling a Print Job ................................................................................. 40
Uninstalling Printer Drivers .......................................................................... 41
Printer Driver Functions (Macintosh) ............................................................42
Description of Print Settings ........................................................................ 43
BJ Print Monitor ........................................................................................... 59
Cancelling a Print Job ................................................................................. 61
2
Table of Contents
Using the Printer with a Network ................................................................. 62
Uninstalling Printer Drivers .......................................................................... 66
Routine Maintenance ....................................................................................67
When to Replace Ink Tank and Maintain Print Head .................................. 68
Replacing an Ink Tank ................................................................................. 69
Printing the Nozzle Check Pattern .............................................................. 74
Print Head Cleaning .................................................................................... 78
Print Head Deep Cleaning ........................................................................... 81
Cleaning the Printer ..................................................................................... 83
Transporting the Printer ............................................................................... 85
Printing Media ...............................................................................................89
Compatible Media Types ............................................................................. 90
Envelopes .................................................................................................... 92
High Resolution Paper HR-101N ................................................................ 96
Glossy Photo Paper GP-301 ....................................................................... 98
High Gloss Photo Film HG-201 ................................................................. 100
Glossy Photo Cards FM-101 ..................................................................... 102
Photo Paper Pro PR-101 ........................................................................... 104
Photo Paper Pro PC-101S ........................................................................ 107
Transparencies CF-102 ............................................................................. 109
T-Shirt Transfers TR-201 ........................................................................... 111
Banner Paper ............................................................................................ 113
Troubleshooting ..........................................................................................116
Cannot Install the Printer Driver ................................................................ 117
Print Quality is Poor or Contains Errors ..................................................... 119
3
Table of Contents
Printer Does Not Start or Stops During Print Jobs .................................... 136
Paper Does Not Feed Properly or Paper Jams ......................................... 142
The POWER Lamp Flashes Orange ......................................................... 145
An Error Message is Displayed on the Screen .......................................... 148
Problems Unique to Windows ................................................................... 158
Problems Unique to the Macintosh ........................................................... 163
Appendices .................................................................................................166
Deleting an Unknown Device (USB interface) .......................................... 167
For Faster Printing .................................................................................... 170
Specifications .............................................................................................173
Index ...........................................................................................................187
4
Introduction
Introduction
Thank you for purchasing the Canon S600/S630 Bubble Jet Printer. This User’s Guide
provides complete explanations of the features and functions of the printer.
The diagrams and computer screens in this guide refer to the S600. The operations are
exactly the same with the S630.
This guide uses the following symbols to indicate important information. Always observe
these instructions.
Warning ➤
Instructions that, if ignored, could result in death or serious personal injury
caused by incorrect operation of the equipment.
Must be observed for safe operation.
Caution ➤
Instructions that, if ignored, could result in personal injury or material
damage caused by incorrect operation of the equipment.
Must be observed for safe operation.
Important ➤
Prohibited actions that, inadvertently performed, could result in equipment
damage, faults or impaired product quality.
Must be avoided for correct operation.
Windows
Information for Windows users only.
Macintosh
Information for Macintosh (USB users only).
5
How to Use This Manual
How to Use This Manual
To view this User’s Guide, we recommend that you use Acrobat Reader 4.0 or Acrobat
Reader 3.0. Please note that screens displayed by Acrobat Reader 3.0 are slightly
different.
Displays the previous page.
Use this button to enlarge the
viewing screen. Select this button in
the tool bar and click within the
screen.
Displays the next page.
Returns to the page
you were previously
viewing.
Click to jump straight to this
page.
6
How to Use This Manual
Use this button to
search for a word.
Displays the table of contents.
Click the heading to jump to the topic.
Click the " " symbol to see the headings for each chapter.
Click the " " symbol to close the headings.
7
Safety Precautions
Safety Precautions
Please read the safety warnings and cautions provided in this manual to ensure that you
use the printer safely. Do not attempt to use the printer in any way not described in this
manual.
Warning ➤
You may cause an electric shock/fire or damage the printer if you ignore
any of these safety precautions.
■ Choosing a location
Do not place the printer close to flammable solvents such as alcohol or thinners.
■ Power supply
Never attempt to plug in or unplug the printer from the power supply when your hands
are wet.
Always push the plug all the way into the power outlet.
Never damage, modify, stretch or excessively bend or twist the
power cord. Do not place heavy objects on the power cord.
8
Safety Precautions
Never plug the printer into a power socket that is shared with other
equipment (extension lead, double adapter, etc.).
Never use the printer if the power cord is bundled or knotted.
If you detect smoke, unusual smells or strange noises around the printer, immediately
unplug the printer at the power supply and call for service.
■ Cleaning the printer
Use a damp cloth to clean the printer. Never use flammable solvents
such as alcohol, benzene or thinners.
If flammable solvents come in contact with electrical components inside the printer,
it could cause a fire or electric shock.
Always unplug the printer from the power outlet before cleaning the printer.
If you accidentally switch the printer on while cleaning it, you could injure yourself or damage the printer.
9
Safety Precautions
■ Maintaining the printer
Do not attempt to disassemble or modify the printer. There are no user serviceable parts
inside the printer.
The printer contains high-voltage components. Never attempt any maintenance procedure not described in
this guide.
■ Working around the printer
Do not use inflammable sprays near the printer.
This could cause a fire or electric shock if the spray comes into contact with electrical components inside
the printer.
10
Safety Precautions
Caution ➤
You may cause injury or damage the printer if you ignore any of these
safety precautions.
■ Choosing a location
Do not install the printer in a location that is unstable or subject to excessive vibration.
Do not install the printer in locations that are very humid or dusty, in direct sunlight,
outdoors, or close to a heating source.
To avoid the risk of fire or electric shocks, install the printer in a location with an ambient temperature range
of 5°C to 35°C (41°F to 95°F) and humidity of 10% to 90% (condensation free).
Do not place the printer on a thick rug or carpet.
Ensure that the area around the power outlet is kept clear at all times
so you can easily unplug the power cord if necessary.
When moving the printer, carry the printer at both ends.
11
Safety Precautions
■ Power supply
Never remove the plug by pulling on the cord.
Do not use an extension lead.
If you do not intend to use the printer for a long period of time, unplug the printer after
turning it off.
Never use a power supply voltage other than that supplied in the country of purchase.
The correct power supply voltages and frequencies are as follows:
Europe: AC 230V ± 10%, 50Hz
USA/Canada: AC 120V, 60Hz
Australia: AC 240V, 50Hz
12
Safety Precautions
■ Working around the printer
Never put your hands or fingers in the printer while it is printing.
Do not place metal objects (paper clips, staples, etc.) or containers of flammable
solvents (alcohol, thinners. etc.) on top of the printer.
If any foreign object (metal or liquid) falls into the printer, unplug the power cord and call
for service.
■ Print heads and ink tanks
For safety reasons store print heads and ink tanks out of the reach of small children.
If a child ingests any ink, consult a doctor immediately.
Do not shake print heads or ink tanks.
Ink may leak out and stain clothing or the surrounding area.
Never touch the electrical contacts on a print head after printing.
The metal parts may be very hot and could cause burns.
13
Printer Parts and Their Functions
Printer Parts and Their Functions
• Front View
• Rear View
• Inside the Printer
• Operation Panel
14
Printer Parts and Their Functions
Front View
Paper Guide
When loading paper, ensure
the left edge just touches
this guide.
To move the paper guide,
pinch the knob and slide in
the appropriate direction.
Operation Panel
For details, refer to
"Operation Panel."
Paper Rest
Sheet Feeder
Load paper here.
Paper feeds
automatically, one sheet
at a time.
Paper Output Tray
Front Cover
Open to replace the
ink tanks or remove
jammed paper.
Front View
15
Printer Parts and Their Functions
Rear View
USB Port
This connector is used to connect
the printer to a computer through
a USB interface.
Printer Port (Parallel)
This connector is used to connect
the printer to a computer through
a parallel interface.
Rear View
16
Printer Parts and Their Functions
Inside the Printer
Paper Thickness Lever
Adjusts the gap between the print head and the surface of the printing paper.
Print Head Holder
Install the print head here.
Print Head Lock Lever
Locks the print head into the holder.
Once the print head is installed, do not touch this lever.
Inside the Printer
17
Printer Parts and Their Functions
Operation Panel
POWER Button
Press to turn the printer
on or off.
RESUME/CANCEL Button
Press to resume printing once an error has
been resolved. The printer will then
initialise ready for printing.
Also, to cancel printing in progress, press
this button.
POWER Lamp
Off: the printer is turned off.
Green: the printer is ready to print.
Flashing green: the printer is preparing to print, or is currently printing.
Flashing orange: an error has occurred and the printer is not ready to print.
Flashing orange and green alternately: an error has occurred that may require a service
call.
Operation Panel
18
Printer Driver Functions (Windows)
Printer Driver Functions (Windows)
• Opening the Printer Properties Dialog Box
• Printer Properties Dialog Box Description
• BJ Status Monitor Functions
• Cancelling a Print Job
• Uninstalling Printer Drivers
19
Printer Driver Functions (Windows)
Opening the Printer Properties Dialog Box
The Printer Properties dialog box can be opened from either within an application, or
directly from the Windows [Start] menu.
■ Opening the Printer Properties dialog box from your application program
This method is generally used to specify printer settings just before printing.
The operations may vary slightly depending on your application program. This section
describes only the general procedure for opening the Printer Properties dialog box.
1
In your application, select the command to print a document.
The [Print] dialog box can usually be opened by selecting [Print] from the
[File] menu.
2
Ensure that [Canon S600] / [Canon S630] is selected in the [Name] field.
Then click the [Properties] button.
The Printer Properties dialog box opens.
Note
➤
Depending on your application program, the command and menu names
may differ, and there may be more steps involved in opening the Printer
Properties dialog box. For further details, see the user's manual for your
application.
Opening the Printer Properties Dialog Box
20
Printer Driver Functions (Windows)
■ Opening the Printer Properties dialog box directly from the [Start] menu
This method is used for maintenance operations such as print head cleaning, or to
specify printer settings common to all application programs.
When the Printer Properties dialog box is opened from the [Start] menu, the Windows
operating system adds several tabs, including the [Details] tab. These do not appear
when the Printer Properties dialog box is opened from within an application.
For further information about these additional tabs, refer to your Windows
documentation.
1
Click the [Start] button, then select [Settings], [Printers].
2
Select the [Canon S600] / [Canon S630] icon.
3
Open the [File] menu and select:
• Windows 95/Windows 98/Windows Me ➔ [Properties]
• Windows 2000 ➔ [Printing Preferences...]
• Windows NT4.0 ➔ [Document Defaults...]
The Printer Properties dialog box opens.
Opening the Printer Properties Dialog Box
21
Printer Driver Functions (Windows)
Printer Properties Dialog Box Description
• [Main] Tab
• [Page Setup] Tab
• [Stamp/Background]
Tab (Windows 95/
Windows 98/
Windows Me only)
• [Effects] Tab
• [Profiles] Properties
Tab
• [Maintenance]
Properties Tab
Note
➤
The screens in this section refer to Windows 95/Windows 98/Windows Me
operation. The equivalent screens for Windows 2000 and Windows NT4.0
may look slightly different.
Printer Properties Dialog Box Description
22
Printer Driver Functions (Windows)
[Main] Tab
(1)
(2)
(6)
(3)
(4)
(5)
(1)
(2)
[Media Type]
Ensure this setting matches the type of media loaded in the printer.
[Print Quality]
Select the print quality you require from among the different options. To select custom
Print quality, select [Custom] and click the [Set...] button.
Printer Properties Dialog Box Description
23
Printer Driver Functions (Windows)
(3)
(4)
(5)
(6)
[Colour Adjustment]
Select the method of colour adjustment. To make detailed colour adjustments, select
[Manual], then click the [Set...] button.
[Greyscale Printing]
Select to print a greyscale version of a colour document.
[Print Advisor...]
Click to start the Print Advisor.
The Print Advisor simplifies configuration of the printer driver. By having the user
answer a series of questions, the Printer Advisor automatically configures the printer
driver settings.
Preview Area
Before starting printing, verify that settings such as the lever position are correct.
Note
➤
To see a description of any item in the Printer Properties dialog box, click
the [?] mark then click the desired item. To see a description of operating
procedures, click the [Help] button. If the button does not appear when
using Windows 2000 or Windows NT4.0, click the [Start] button then select
[Programs] - [Canon S600] / [Canon S600] - [Help].
Printer Properties Dialog Box Description
24
Printer Driver Functions (Windows)
[Page Setup] Tab
■ For Windows 95, Windows 98, Windows Me
(1)
(2)
(3)
(6)
(4)
(5)
(1)
[Page Size]
Ensure the correct paper size is selected.
Printer Properties Dialog Box Description
25
Printer Driver Functions (Windows)
(2)
(3)
(4)
(5)
(6)
[Orientation]
Select landscape or portrait printing and ensure it is the same orientation used in the
application.
[Printing Type] (Only for Windows 95, Windows 98 and Windows Me)
Select the printing method from among the following.
[Normal-size Printing] The document is printed according to the original
dimensions. This setting is usually selected by default.
[Scaled Printing]
The document is resized when printed. When this is
selected, you can specify the [Printer Paper Size] and
[Resize Percentage].
[Page Layout Printing] Pages are reduced and printed so that two or four document
pages fit on each printed page.
[Poster Printing]
This enlarges and splits the print image across several
sheets of paper. The printed sheets can then be assembled
to make a large poster.
[Banner Printing]
Select this when printing on banner paper.
[Reverse order]
When selected, the document starts printing with the last page.
[Collate]
Select to print multiple copies of the document one copy at a time.
Preview Area
Verify the overall layout, stamps, background, etc., to be applied to the print job.
Printer Properties Dialog Box Description
26
Printer Driver Functions (Windows)
■ For Windows 2000 and Windows NT4.0
This section only describes the functions unique to Windows 2000 and Windows NT4.0.
Other functions are identical to Windows 95, Windows 98 and Windows Me. See the
previous two pages for more details.
(1)
(2)
Printer Properties Dialog Box Description
27
Printer Driver Functions (Windows)
(1)
(2)
[Scaled Printing]
To resize the document for printing, select this check box, and then in [Printer Paper
Size], select a size indicated by [Page Size], or select [Scaling] and specify the scaling
factor (20% - 400%).
[Page Layout] (Not available in Windows NT 4.0)
Use this function to print more than one page on a single sheet of paper. Typically, this
setting is set to display [1-up Printing]. If another option is selected, [Page Border] is
no longer greyed out. Select this check box to place a border around each page.
Printer Properties Dialog Box Description
28
Printer Driver Functions (Windows)
[Stamp/Background] Tab (Windows 95/Windows 98/
Windows Me only)
(1)
(2)
(3)
(4)
(5)
(7)
(8)
(1)
(2)
(6)
[Stamp]
Select the check box and choose the stamp.
[Place stamp over text]
When selected, the stamp is printed over the print data.
Printer Properties Dialog Box Description
29
Printer Driver Functions (Windows)
(3)
(4)
(5)
(6)
(7)
(8)
[Stamp first page only]
Prints the stamp only on the first page.
[Define Stamp...]
This allows you to create new stamps, or modify details of a selected stamp.
[Background]
Select the check box and choose the background image you wish to use.
[Background first page only]
Prints the background image only on the first page.
[Select Background...]
This allows you to register a new background, or to display details of the background
you have selected.
Preview Area
Printer Properties Dialog Box Description
30
Printer Driver Functions (Windows)
[Effects] Tab
(1)
(5)
(2)
(3)
(4)
(1)
[Simulate Illustration]
This function manipulates colour image data with certain effects. Select the check box
and adjust the brightness of the image with the [Contrast] slide bar.
Printer Properties Dialog Box Description
31
Printer Driver Functions (Windows)
(2)
(3)
(4)
(5)
[Monochrome Effects]
Prints a colour image in a single colour. Select the check box and choose a colour or
use a custom colour using [Select Colour].
[Image Optimizer]
Improves the contours and jaggedness that occur when photographic or graphic
image data is enlarged within an application.
[Photo Optimizer PRO]
Optimises the colour of images taken from a digital camera or scanner. It is especially
effective for images affected by colour imbalance and over- or under exposure.
When printing several images on one page, optimisation is usually applied to each
image according to its requirements. However, if the image data has been
manipulated using cut and paste, rotation or other such operations, group optimisation
of all images on the one page is recommended. In such cases, select the [Apply
Throughout Page] check box.
Preview Area
Printer Properties Dialog Box Description
32
Printer Driver Functions (Windows)
[Profiles] Properties Tab
(2)
(1)
(3)
(4)
(6)
(5)
(1)
[Printing Profiles]
This list displays the printing settings currently registered in the Profiles tab.
The [Current Settings] profile contains the settings currently specified in the [Main],
[Page Setup] and [Effects] tabs. The [Default Settings] profile contains the factory
default settings.
Printer Properties Dialog Box Description
33
Printer Driver Functions (Windows)
(2)
(3)
(4)
(5)
(6)
[Details]
Displays all the printer settings selected in [Printing Profiles].
[Description]
Displays a description of the printer settings selected in [Printing Profiles]. You can
enter the description when saving the printer settings.
[Add to Profiles...]
Click to save the settings currently specified in the [Main], [Page Setup] and [Effects]
tabs. Select [Current Settings] in the [Printing Profiles] list then click this button. The
[Add to Profiles...] dialog box appears.
[Retrieve from Profiles]
Click to activate registered printer settings. The contents of the [Main], [Page Setup]
and [Effects] tabs are changed by selecting the printer settings in [Printing Profiles]
and then clicking this button.
This button is disabled when [Current Settings] is selected.
[Delete]
Click to delete unwanted printer settings. Select the unwanted item in the [Printing
Profiles] list and click the [Delete] button.
[Current Settings] and [Default Settings] cannot be deleted.
Printer Properties Dialog Box Description
34
Printer Driver Functions (Windows)
[Maintenance] Properties Tab
(1)
(2)
(3)
(5)
(6)
(4)
(7)
(8)
(1)
(2)
[Cleaning]
Click to start print head cleaning.
[Deep Cleaning]
Click to start print head deep cleaning.
Use this function only if [Cleaning] has not improved the print quality.
Printer Properties Dialog Box Description
35
Printer Driver Functions (Windows)
(3)
(4)
(5)
(6)
(7)
(8)
[Nozzle Check]
Prints the nozzle check pattern to ensure the print head nozzles are outputting ink
normally. For details, refer to “Examining the Nozzle Check Pattern”.
[Print Head Alignment]
Aligns the print head. For details on print head alignment, refer to Quick Start Guide.
[Power Off]
Click to turn the printer off.
[Auto Power]
This allows you to turn the printer off when no data is sent to the printer for a certain
period of time, or turn the printer back on again when data is sent to the printer.
[Custom Settings...]
Click to modify the printer mode. Change the settings in the [Custom Setting] dialog
box and click [Send] to change printer mode.
[Start Status Monitor]
Click to start the BJ Status Monitor, to check the printer status and the progress of
printing jobs.
Printer Properties Dialog Box Description
36
Printer Driver Functions (Windows)
BJ Status Monitor Functions
The BJ Status Monitor allows you to check the status of the printer.
If an error occurs, the status monitor indicates the nature of the error and suggests an
appropriate solution. The status monitor also checks the ink tanks and displays a warning
message when the ink is low.
■ Launching the BJ Status Monitor
The BJ Status Monitor launches automatically when data is sent to the printer. When
launched, the BJ Status Monitor appears as an icon on the Task Bar.
1
Click the [Canon BJ Status Monitor] icon on the Task Bar.
The BJ Status Monitor appears.
BJ Status Monitor Functions
37
Printer Driver Functions (Windows)
Note
➤
To open the BJ Status Monitor when the printer is not printing, click the
[Maintenance] tab in the Printer Properties dialog box and click the [Start
Status Monitor] button.
BJ Status Monitor Functions
38
Printer Driver Functions (Windows)
■ When errors occur or ink runs low
The BJ Status Monitor is automatically displayed when an error occurs, e.g. if the printer
runs out of paper or ink is low.
In such cases, take the appropriate action as described in the [Printer Status] tab.
In Windows 95, Windows 98 or Windows Me, click the [Guide] tab and follow the
instructions on screen.
When paper has run out:
Note
➤
When the ink level is low:
For details on the BJ Status Monitor, select the [Help] menu and click on
the topic of interest.
BJ Status Monitor Functions
39
Printer Driver Functions (Windows)
Cancelling a Print Job
To cancel the current print job, first open the BJ Status Monitor.
Note
1
Click the [Canon BJ Status Monitor] icon on the Task Bar.
2
Click [Cancel Printing].
➤
If [Cancel Printing] is greyed out, press the printer's RESUME/CANCEL
button to terminate the print job.
Cancelling a Print Job
40
Printer Driver Functions (Windows)
Uninstalling Printer Drivers
Use the Uninstaller to delete any unwanted printer drivers. This allows you to delete all the
files associated with the printer driver at the same time.
1
Click the [Start] button and select [Programs], [Canon S600] / [Canon
S630], [Uninstall].
2
Click [Yes] when the confirmation message appears.
3
When all the files have been deleted, click [OK].
The deletion of the printer driver is complete.
If a message prompts you to restart your computer, click [OK] to restart your computer.
Note
➤
In Windows 95, Windows 98 or Windows Me, you can also start the
Uninstaller by double-clicking on [Uninstall] in the [Canon S600] / [Canon
S630] folder on the desktop.
Uninstalling Printer Drivers
41
Printer Driver Functions (Macintosh)
Printer Driver Functions (Macintosh)
• Description of Print Settings
• BJ Print Monitor
• Cancelling a Print Job
• Using the Printer with a Network
• Uninstalling Printer Drivers
42
Printer Driver Functions (Macintosh)
Description of Print Settings
• [Page Setup] Dialog Box
• [Printer Utility]
Dialog Box
• [Print] Dialog Box
• [Detailed Setting]
Dialog Box
• [Options] Dialog Box
• [Register Settings]
Dialog Box
Description of Print Settings
43
Printer Driver Functions (Macintosh)
[Page Setup] Dialog Box
The Page Setup dialog box contains settings for the printed page, such as the size of the
print media, and resizing the printed image. To open the Page Setup dialog box, select
[Page Setup] from the [File] menu in your application program.
(1)
(2)
(8)
(3)
(5)
(6)
(4)
(7)
(1)
(2)
[Paper Size]
Select the size of the paper for the print job. To enter the size manually, select [Custom
1] - [Custom 3] and click [Custom].
[Banner Printing]
Select this check box when printing on banner paper.
Description of Print Settings
44
Printer Driver Functions (Macintosh)
(3)
(4)
(5)
(6)
(7)
(8)
[Scale]
Specify the scaling percentage to resize the document for printing.
[Orientation]
Select landscape or portrait printing.
[Custom]
To specify a custom paper size, click this button to open the [Custom] dialog box after
selecting [Custom 1] to [Custom 3] in the [Paper Size] popup menu. The [Custom]
Dialog Box allows you to specify the length and width of the paper.
[Utilities]
Click to open the [Printer Utility] dialog box for maintenance operations such as print
head cleaning and nozzle check pattern printing, as well as for changing the print
mode.
[Save Settings]
Saves the settings specified in the [Page Setup] dialog box.
Preview Area
This image allows you to confirm how the document will print with the selected paper
settings.
Description of Print Settings
45
Printer Driver Functions (Macintosh)
[Printer Utility] Dialog Box
The [Printer Utility] dialog box is displayed when you click the [Utilities] button in the [Page
Setup] dialog box.
(1)
(2)
(1)
(2)
Select the function you wish to perform.
Display area showing the various maintenance functions, including cleaning and test
pattern printing. Click the icon to start this function. For further details, refer to
"Routine Maintenance".
➡ Printing the Nozzle Check Pattern
Description of Print Settings
46
Printer Driver Functions (Macintosh)
➡ Print Head Cleaning
➡ Print Head Deep Cleaning
Note
➤
For information about Print Head Alignment, refer to the Quick Start Guide.
Description of Print Settings
47
Printer Driver Functions (Macintosh)
[Print] Dialog Box
The [Print] dialog box specifies the media type and print settings to be used for your print
job. To open the [Print] dialog box, select [Print] from the [File] menu in your application
program.
(1)
(3)
(4)
(5)
(6)
(2)
(1)
(2)
(3)
[Media Type]
Ensure this setting matches the type of paper media loaded in the printer.
[Greyscale Printing]
Select to print a greyscale version of a colour document.
[Print Mode]
Select the icon that most closely resembles your document and required print results.
Description of Print Settings
48
Printer Driver Functions (Macintosh)
(4)
(5)
(6)
[Details...]
Allows you to manually set the print quality and colour settings in the [Detailed Setting]
Dialog Box.
[Options...]
Specify the output destination, print order and page layout for the document you are
printing.
[Apply...]
Allows you to register print settings or to implement a previously registered print
setting.
Description of Print Settings
49
Printer Driver Functions (Macintosh)
[Detailed Setting] Dialog Box
To open the [Detailed Setting] dialog box, select [Manual]
then click [Details...].
(1)
in the [Print] dialog box and
(2)
(3)
(4)
(1)
Panel display icons
Click these icons to switch between panels in the [Detailed Setting] dialog box.
Description of Print Settings
50
Printer Driver Functions (Macintosh)
(2)
(3)
(4)
[Print Quality]
Move the slide bar to adjust the balance between print quality and speed. Moving the
bar to the right enhances print quality, and moving it to the left increases printing
speed.
[Halftoning]
Select either [Dither] or [Diffusion] ink dot configurations.
[Photo Optimizer PRO]
Optimises the colour of images taken from a digital camera or scanner. It is especially
effective for images affected by colour imbalance and over- or under exposure.
When printing several images on one printing page, optimisation is usually applied to
each image according to its requirements. However, if the image data has been
manipulated using cut and paste, rotation or other such operations, group optimisation
of all images on the page is recommended. In such cases, select the [Apply
Throughout Page] check box.
Description of Print Settings
51
Printer Driver Functions (Macintosh)
■ [Special Effects] Panel
To display the [Special Effects] panel, click the [Special effects] display icon.
(1)
(3)
(2)
(1)
[Simulate illustration]
This function manipulates colour image data to produce illustration effects. To use the
function, select the check box. To adjust the brightness of the image, drag the
[Contrast] slide bar. Dragging the slider to the right brightens the image.
Description of Print Settings
52
Printer Driver Functions (Macintosh)
(2)
(3)
[Monochrome effects]
Prints a colour image in a single colour. Select the check box and choose the colour
you wish to use.
Preview Area
Description of Print Settings
53
Printer Driver Functions (Macintosh)
■ [Colour] Panel
To display the [Colour] panel, click the [Colour] display icon.
(1)
(2)
(3)
(4)
(5)
(6)
(1)
[Colour Correction]
Select a colour correction method: [BJ Standard], [ColourSync] or [None]. [BJ
Standard] is usually the optimum colour correction method for printing with a BJ
printer. When [ColourSync] is selected, you should also specify the [Print Type] and
[Printer Profile] settings.
Description of Print Settings
54
Printer Driver Functions (Macintosh)
(2)
(3)
(4)
(5)
(6)
[Print Type]
For printing that emphasises intermediate colours, select [Photo]. For printing that
emphasises the brightness of primary colours, select [Graphics]. For documents that
contain large amounts of a basic colour, select [Spot Colour].
[Printer Profile]
Select optimised colour characteristics (a profile) for the media type and other factors.
[Gamma Correction]
This function adjusts the colour contrast (not including pure black and white). To adjust
the contrast, select the check box and move the slide bar. Moving the bar to the right
darkens the entire image while increasing contrast in the lighter areas and decreasing
contrast in the darker areas.
[Colour Balance]
Move the bar for each colour to adjust the balance of colour intensity. Moving the bar
to the right intensifies the colour.
[Intensity]
Move the slide bar to adjust the print density. Moving the bar to the right increases the
density.
Description of Print Settings
55
Printer Driver Functions (Macintosh)
[Options] Dialog Box
To open the [Options] dialog box, click the [Options...] button in the [Print] dialog box.
(1)
(2)
(3)
(5)
(1)
(2)
(4)
[Destination]
Select the print output destination. [Printer] is the usual selection.
To check the layout or other image elements before printing, select [Preview]. To save
the document as a PICT file, select [PICT File].
[Print in reverse order]
Prints the document starting with the last page.
Description of Print Settings
56
Printer Driver Functions (Macintosh)
(3)
(4)
(5)
[Print collated pages]
Prints multiple copies of the document one copy at a time.
[Page Layout]
Allows you to print two or four pages of a document on a single page. If you select [2
Up] or [4 Up], you should also set the [Page Order] to specify the document page
order for printing. The [Page Border] option allows you to select whether to print a
border around the individual document pages.
Preview Area
Description of Print Settings
57
Printer Driver Functions (Macintosh)
[Register Settings] Dialog Box
To open the [Register Settings] dialog box, click the [Apply...] button in the [Print] dialog box.
(1)
(1)
(2)
(3)
(4)
(5)
(2)
(3)
(4)
(5)
[Settings]
Displays a list of the registered print settings.
[Import]
Imports a set of print settings. To use the settings, select the desired settings in the
[Settings] list and click the [Import] button.
[Apply]
Saves the settings currently specified in the [Print] dialog box. After clicking the button,
enter the name under which the settings are to be saved.
[Remove]
Deletes unwanted print settings. To delete unwanted settings, select the settings in
[Settings] and click the [Remove] button.
[Defaults]
Restores the print settings selected in [Settings] to defaults. A check mark appears
next to the selected print settings.
Description of Print Settings
58
Printer Driver Functions (Macintosh)
BJ Print Monitor
The BJ Print Monitor allows you to check the progress of print jobs.
You can launch the BJ Print Monitor if background printing is enabled in the [Chooser] utility.
■ Opening the BJ Print Monitor
1
Select [Chooser] from the Apple Menu.
2
Set [Backgrounding] to [On].
3
Select [BJ Print Monitor] in the Application Menu.
The BJ Print Monitor launches.
BJ Print Monitor
59
Printer Driver Functions (Macintosh)
■ BJ Print Monitor Functions
... Click to pause printing of the specified document.
... Click to resume printing.
... Click to cancel printing of the specified document.
Displays information about the document currently being printed.
The icon on the left becomes darker as the printing progresses.
Displays information about the documents queued for printing.
The BJ Print Monitor allows you to change the print order of documents queued for printing.
To change the print order, place the mouse pointer over the name of the document, hold the
mouse button down while dragging the document name to the new position, then release.
Note, however, that you cannot change the print order of a document already printing.
BJ Print Monitor
60
Printer Driver Functions (Macintosh)
Cancelling a Print Job
When the BJ Print Monitor is running, you can use it to cancel or suspend the currently
printing job.
1
Select [BJ Print Monitor] in the Application Menu.
2
Click the name of the print job you wish to cancel, then click
.
The document selected in the Print Monitor is deleted from the print list and
the print job is cancelled.
Note
➤
To suspend printing, click the name of the document being printed then
click
. To resume printing, click
.
Cancelling a Print Job
61
Printer Driver Functions (Macintosh)
Using the Printer with a Network
The printer can be used with an Ethernet network environment.
Follow the steps described below to connect the printer to the network.
■ Before Setting up the Printer
• Install the printer driver on each network computer that will use the printer.
For information on installation, refer to the Quick Start Guide.
• Use a USB cable to connect the printer to the computer that will function as the print
server.
■ Printer Setup
To use the printer on a network, first set up the print server, then set up each client
machine.
• Print server setup procedure
1
Select [Chooser] in the Apple Menu.
2
Select [Active] in [AppleTalk].
3
Select the [S600] / [S630] icon, then select the printer name in [Connected
to:].
Using the Printer with a Network
62
Printer Driver Functions (Macintosh)
4
Click [Share].
5
Confirm that [S600 server] / [S630 server] is selected in [Enter new print
server name:] then click [Send].
6
Confirm that the new print server name has been added to [Current print
servers] then click [Close].
7
Click the close box to close the Chooser.
• Client setup procedure
1
Select [Chooser] in the Apple Menu.
2
Select [Active] in [AppleTalk].
3
Select the [S600 (Server)] / [S630 (Server)] icon, then select the printer
server in [Connected to:].
4
Click the close box to close the Chooser.
Using the Printer with a Network
63
Printer Driver Functions (Macintosh)
■ Checking Print Status
• Checking print status from the print server
To check the status of a print job from the print server, start the BJ Print Monitor.
Select [BJ Print Monitor] in the Application Menu.
To close the BJ Print Monitor, select [Close Status Window] in the [File] menu.
• Checking print status from a client
To check the status of a print job from a client, start the BJ Status Monitor. Click the
[BJ Status Monitor] icon in the [BJ Extras] folder.
To close the BJ Status Monitor, select [Quit] in the [File] menu.
• The BJ Print Monitor and BJ Status Monitor
The BJ Print Monitor and the BJ Status Monitor both display a list of information
concerning documents queued for printing. This information includes the document
name, number of pages, number of copies and the time when the print job was
accepted. The total number of queued documents is also displayed.
The BJ Print Monitor allows you to change the print order of the queued documents.
➡ BJ Print Monitor Functions
➡ BJ Status Monitor Functions
Using the Printer with a Network
64
Printer Driver Functions (Macintosh)
■ BJ Status Monitor Functions
.... Click to pause printing of the specified document.
.... Click to resume printing.
.... Click to cancel printing of the specified document.
Note
➤
• You can determine the owner of a computer by selecting the [File
Sharing] control panel and checking the [Owner Name] item.
• If you are using two or more printer servers, you can switch between the
BJ Status Monitor displays. Select [Print Server] in the [File] menu, then
select the desired print server and click [OK].
Using the Printer with a Network
65
Printer Driver Functions (Macintosh)
Uninstalling Printer Drivers
When a printer driver is no longer needed, use the Installer to delete, all the program files
associated with it at the same time.
Before proceeding, ensure you save any unsaved files in any currently running applications.
Note
1
Load the Printer Driver/User's Guide CD-ROM.
2
Double-click the [Printer Driver] folder.
3
Double-click the [Installer] icon.
4
When the Software License Agreement is displayed, click [Accept].
5
Select [Uninstall] from the popup menu and then click [Uninstall].
➤
If a warning message appears indicating that other applications are
running:
• Click [Cancel] and save the document(s) if there are any unsaved
documents open in the other applications.
• Click [Continue] to continue the uninstall operation.
6
After the uninstall is complete, a message appears prompting you to restart
your computer. Click [Restart].
Uninstalling Printer Drivers
66
Routine Maintenance
Routine Maintenance
• When to Replace Ink Tank and Maintain Print Head
• Replacing an Ink Tank
• Printing the Nozzle Check Pattern
• Print Head Cleaning
• Print Head Deep Cleaning
• Cleaning the Printer
• Transporting the Printer
67
Routine Maintenance
When to Replace Ink Tank and Maintain Print Head
When an ink tank is empty, it must be replaced.
The BJ Status Monitor (Windows) or the BJ Print Monitor (Macintosh) will initially advise
you of a low ink level. At this stage, you can still continue to print.
Once an ink tank is empty, the BJ Status Monitor (Windows) or the BJ Print Monitor
(Macintosh) will tell you to replace the ink tank. Attempting to print causes the POWER
lamp to flash four times.
➡ Replacing an Ink Tank
If printing becomes faint or a specific colour is no longer printing, even though there is still
enough ink, the print head nozzles are probably clogged. Follow the procedures below to
clean the nozzles.
➡ Printing the Nozzle Check Pattern
If the print quality is poor
➡ Print Head Cleaning
If the problem remains
➡ Print Head Deep Cleaning
If print head deep cleaning does not resolve the problem, the print head may be worn out.
Contact a Canon service representative.
When to Replace Ink Tank and Maintain Print Head
68
Routine Maintenance
Replacing an Ink Tank
When replacing an ink tank, check the model number very carefully. The printer will not print
properly if the wrong ink tank is used, or installed in the incorrect position.
With this printer, ink tanks must be installed from the right in the order indicated below.
•
•
•
•
Yellow: BCI-3eY
Magenta: BCI-3eM
Cyan:
BCI-3eC
Black:
BCI-3eBK
Note
➤
Damage caused by using a refilled cartridge is not covered by the Canon
warranty. Canon recommends using only original Canon ink tanks to
ensure the best quality.
1
Ensure that the printer is on, and then open the front cover.
The print head holder moves to the centre.
Replacing an Ink Tank
69
Routine Maintenance
2
Remove the empty ink tank.
Push the tab and remove the ink tank.
Do not touch the lock lever; remove only the ink tank.
Important ➤
• Handle ink tanks carefully to avoid staining clothing or the surrounding
area.
• Discard empty ink tanks according to the local laws and regulations
regarding disposal of consumables.
Replacing an Ink Tank
70
Routine Maintenance
3
Unpack the new ink tank and pull off the orange tape.
Replacing an Ink Tank
71
Routine Maintenance
4
Remove the orange protective cap from the bottom of the ink tank.
Never press here!
Ink may squirt out of the tank.
Important ➤
• Do not re-attach the protective cap once you have removed it.
• Once you have removed the protective cap, do not touch the open ink
port.
Replacing an Ink Tank
72
Routine Maintenance
5
Insert the ink tank in the print head holder.
Press on the "PUSH" mark until the ink tank snaps firmly into place.
6
Close the front cover.
The print head holder moves to the right. The ink tank installation process
is now complete.
Note
➤
• To maintain optimal print quality, use an ink tank within six months of first
use.
• Once an ink tank has been used, do not remove it from the printer and
leave it out in the open. An ink tank left out in the open and then
reinstalled in the printer may not function.
Replacing an Ink Tank
73
Routine Maintenance
Printing the Nozzle Check Pattern
Print the nozzle check pattern to determine whether the ink sprays normally from the print
head nozzles, and to verify print head alignment. Use this function when printed results are
blurred or the colour is incorrect.
Nozzle check pattern printing can be executed from the Windows and Macintosh printer
drivers, or from the printer itself.
■ Printing the Nozzle Check Pattern from the Printer Drivers
Windows
1
With the printer on, load a sheet of A4 or Letter paper in the printer.
2
Open the Printer Properties dialog box.
➡ Opening the Printer Properties Dialog Box
3
Click the [Maintenance] tab and then click the [Nozzle Check] icon.
4
When the confirmation message is displayed, click [OK].
➡ Examining the Nozzle Check Pattern
Printing the Nozzle Check Pattern
74
Routine Maintenance
Macintosh
1
With the printer on, load a sheet of A4 or Letter paper in the printer.
2
Open the Page Setup dialog box.
The Page Setup dialog box can normally be opened by selecting [Page
Setup...] in the [File] menu.
3
Click the [Utilities] button to open the Printer Utilities dialog box.
4
Select [Test Print] from the pull-down menu, and then click the [Nozzle
Check] icon.
5
When the confirmation message is displayed, click [OK].
➡ Examining the Nozzle Check Pattern
Printing the Nozzle Check Pattern
75
Routine Maintenance
■ Printing the Nozzle Check Pattern through the Printer
1
With the printer on, load a sheet of A4 or Letter paper in the printer.
2
Hold the RESUME/CANCEL button down until the POWER lamp flashes
twice.
➡ Examining the Nozzle Check Pattern
Printing the Nozzle Check Pattern
76
Routine Maintenance
■ Examining the Nozzle Check Pattern
The nozzle check pattern should appear as follows when ink is discharged properly.
Examine the nozzle check pattern output by the printer.
Lines missing here indicate the
print head requires cleaning.
Unevenness in these patterns
indicates the print head requires
alignment.
Horizontal stripes in these
patterns indicate the print head
requires alignment.
Printing the Nozzle Check Pattern
77
Routine Maintenance
Print Head Cleaning
Clean the print head if you suspect that the nozzles might be clogged.
Head cleaning can be performed either from the printer drivers or from the printer itself.
Note
➤
Cleaning the head consumes ink, so perform head cleaning only when
necessary.
■ Cleaning the Print Head from the Printer Drivers
Windows
1
Ensure that the printer is on.
2
Open the Printer Properties Dialog Box.
➡ Opening the Printer Properties Dialog Box
3
Click the [Maintenance] tab and then click the [Cleaning] icon.
Print Head Cleaning
78
Routine Maintenance
4
Select the ink nozzles to be cleaned, and then click [Execute].
All colours:
Black:
Colour:
5
All nozzles
Black ink nozzles
Colour ink nozzles
When the confirmation message is displayed, click [OK].
Macintosh
1
Ensure the printer is on.
2
Open the Page Setup dialog box.
The Page Setup dialog box can normally be opened by selecting [Page
Setup...] in the [File] menu.
3
Click the [Utilities] button to open the Printer Utility dialog box.
4
Select [Cleaning] from the pull-down menu, and then click the [Cleaning]
icon.
Print Head Cleaning
79
Routine Maintenance
5
Select the ink nozzles to be cleaned, and then click [OK].
All colours: All nozzles
Black:
Black ink nozzles
Colour:
Colour ink nozzles
■ Cleaning the Print Head from the Printer
This operation cleans all nozzles, both black and colour. Because this method also resets
the printer, any print data stored in the printer is lost.
1
Ensure the printer is on.
2
Hold down the RESUME/CANCEL button until the POWER lamp flashes
once.
Now the POWER lamp starts flashing and print head cleaning begins. Do not perform any
other operations until the head cleaning finishes. This takes about 40 seconds.
After print head cleaning finishes, print the nozzle check pattern to verify that the print
heads are clean.
➡ Printing the Nozzle Check Pattern
Print Head Cleaning
80
Routine Maintenance
Print Head Deep Cleaning
If print quality does not improve by standard print head cleaning, try deep cleaning, which is
a more powerful process. Perform print head deep cleaning from the printer driver.
Note
➤
Print head deep cleaning consumes ink, so perform this procedure only
when necessary.
Windows
1
Ensure the printer is on.
2
Open the Printer Properties dialog box.
➡ Opening the Printer Properties Dialog Box
3
Click the [Maintenance] tab and then click the [Deep Cleaning] icon.
4
When the confirmation message is displayed, click [OK].
Print Head Deep Cleaning
81
Routine Maintenance
Macintosh
1
Ensure the printer is on.
2
Open the Page Setup dialog box.
The Page Setup dialog box can normally be opened by selecting [Page
Setup...] in the [File] menu.
3
Click the [Utilities] button to open the Printer Utility dialog box.
4
Select [Cleaning] from the pull-down menu, and then click the [Deep
Cleaning] icon.
5
Click [OK].
Now the POWER lamp starts flashing and print head deep cleaning begins. The process
takes one or two minutes to complete, so simply wait until the POWER lamp stops flashing.
After print head deep cleaning finishes, print the nozzle check pattern to verify that the head
is clean. If not, perform print head deep cleaning once more. If the head is still not clean
after the second deep cleaning, the print head may be worn out, even if ink remains in the
ink tanks. In this event, contact a Canon service representative.
➡ Printing the Nozzle Check Pattern
Print Head Deep Cleaning
82
Routine Maintenance
Cleaning the Printer
During normal printing, ink and small scraps of paper accumulate in the printer. When the
accumulated debris becomes clearly visible, clean the printer by the following procedure.
1
Turn the printer off.
2
After making sure that the POWER lamp is off, unplug the printer.
Caution ➤
Always ensure you unplug the printer before cleaning the printer to avoid
an electric shock.
Cleaning the Printer
83
Routine Maintenance
3
Open the front cover, and wipe out the interior of the printer with a dry cloth.
Wipe away any stray drops of ink, scraps of paper, and dust. Pay special
attention to cleaning the black panel that can be most easily soiled. Do not
touch any of the printer's internal components, such as the print head
holder.
Warning ➤
Do not use any flammable solvents such as paint thinner, benzene or
alcohol.
Black panel
Cleaning the Printer
84
Routine Maintenance
Transporting the Printer
Pack the printer carefully in its original packing materials.
If you do not have the original packing materials, pack the printer carefully and thoroughly in
protective material inside of a sturdy box.
1
Turn the printer off.
2
After making sure that the POWER lamp is off, unplug the printer.
Important ➤
Do not unplug the printer while the POWER lamp is lit or flashing to protect
the printer from damage.
Transporting the Printer
85
Routine Maintenance
3
Remove the paper rest and the paper output tray.
4
Disconnect the printer cable from the computer and from the printer, and
then disconnect the power cord from the printer.
Transporting the Printer
86
Routine Maintenance
5
Secure the printer with adhesive tape as shown, and then pack it in a
plastic bag.
Transporting the Printer
87
Routine Maintenance
6
Attach protective material to both sides of the printer when packing the
printer.
Clearly label the box as "Fragile", if using a transport company.
Transporting the Printer
88
Printing Media
Printing Media
• Compatible Media Types
• Envelopes
• High Resolution Paper HR-101N
• Glossy Photo Paper GP-301
• High Gloss Photo Film HG-201
• Glossy Photo Cards FM-101
• Photo Paper Pro PR-101
• Photo Paper Pro PC-101S
• Transparencies CF-102
• T-Shirt Transfers TR-201
• Banner Paper
89
Printing Media
Compatible Media Types
You can use the following types of paper and other media.
■ Size
• Standard paper: From A5 size (148.0 x 210.0 mm / 5.83 x 8.27 in) to legal size (215.9 x
355.6 mm / 8.5 x 14.0 in)
• Non-standard paper: From 90.0 x 120.0 mm to 215.9 x 584.2 mm
(From 3.54 x 4.72 in to 8.5 x 23.0 in)
• Others: Envelopes (European DL and US Com. #10)
Important ➤
Do not use the following types of paper. Using such paper will not only
produce unsatisfactory results, but can also cause the printer to jam or
malfunction.
• Folded, curled or wrinkled paper
• Wet paper
• Paper that is too thin (less than 64 g/m2 / 17 lb)
• Paper that is too thick (more than 105 g/m2 / 28 lb)
• Picture postcards
• Postcards with an adhered photo or sticker
• Envelopes with a double flap
• Sealed envelopes
• Envelopes with an embossed or treated surface
• Paper with holes (such as loose-leaf paper)
Compatible Media Types
90
Printing Media
■ Weight
64 to 105 g/m2 (17 to 28 lb)
Do not use paper heavier than this, as it could jam in the printer.
■ Types
The following types of media can be used.
For more information about the media and the printing methods, refer to the specific
sections.
Plain paper: Refer to the Quick Start Guide.
➡ Envelopes
➡ High Resolution Paper HR-101N
➡ Glossy Photo Paper GP-301
➡ High Gloss Photo Film HG-201
➡ Glossy Photo Cards FM-101
➡ Photo Paper Pro PR-101
➡ Photo Paper Pro PC-101S
➡ Transparencies CF-102
➡ T-Shirt Transfers TR-201
➡ Banner Paper
Compatible Media Types
91
Printing Media
Envelopes
Use either European DL or US Com. #10 size envelopes.
■ Preparation for Printing
1
Press down on all four corners and edges of the envelopes to flatten them
as shown below.
2
If the envelopes are curled, hold the opposite corners and gently bend
them in the opposite direction.
Ensure that the flap of the envelope is perfectly straight.
Envelopes
92
Printing Media
3
If the leading edge of an envelope is puffed up or curled, use a pen to press
the envelope flat and sharpen the crease.
Press the envelope completely flat,
working from the middle to the edge.
* The above illustrations show a side view of the leading edge of the
envelope.
The envelopes may jam in the printer if they are not completely flat and the
edges are not aligned.
Ensure that no curl or puff exceeds 5 mm (0.2 in).
■ Unsuitable Envelopes
• Envelopes with an embossed or treated surface
• Envelopes with a double flap or pressure seals
Envelopes
93
Printing Media
■ Loading
• Place envelopes lengthwise with the flap to the left and the address side facing
upwards.
• Set the Paper Thickness Lever to the right.
• Up to 10 envelopes can be loaded at once.
Paper
Thickness
Lever
Note
➤
If even after removing any curl in the envelopes they still will not feed
properly, clean the paper feed roller.
1
Ensure the printer is turned on. If any paper is loaded in the printer,
remove the paper.
2
Hold down the RESUME/CANCEL button; when the POWER lamp
flashes three times, release the RESUME/CANCEL button.
Envelopes
94
Printing Media
The paper roller will rotate ten times as it cleans.
Repeat this operation three times.
3
4
Load a sheet of A4 or Letter plain paper in the printer.
Hold down the RESUME/CANCEL button; when the POWER lamp
flashes three times, release the RESUME/CANCEL button.
The paper that is loaded in the printer will feed through the printer and
be ejected.
Repeat this operation three times.
If the printer still will not feed envelopes through even after cleaning the
paper feed roller, perform the procedure described in step 4 again.
■ Printer Driver Settings
• [Media Type]: Envelope
• [Page Size]:
Select either [DL Env.] or [Comm Env. #10] according to the envelope
size you are using.
• [Orientation]: Landscape
■ Handling of Printed Output
Remove each envelope as it is printed.
■ Printable Area
➡ Printing Area
Envelopes
95
Printing Media
High Resolution Paper HR-101N
This type of paper provides better colour reproduction than plain paper. It is suitable for
printing business documents that feature graphics, and for photographs.
■ Loading
• Load the paper with the whiter side facing up.
• Set the Paper Thickness Lever to the left.
• Do not load paper higher than the limit mark. A maximum of 80 sheets can be loaded.
Paper Thickness Lever
Print Side
(Whiter Side)
High Resolution Paper HR-101N
96
Printing Media
■ Printer Driver Settings
• [Media Type]: High Resolution Paper
• [Page Size]:
Ensure the setting matches the size set in the application.
■ Handling of Printed Output
Do not stack more than 50 sheets in the paper output tray. If the output paper is curled, it
may prevent the next sheet being ejected. In this case, or if the ink takes a long time to
dry, remove each sheet as soon as it is printed.
■ Printable Area
➡ Printing Area
High Resolution Paper HR-101N
97
Printing Media
Glossy Photo Paper GP-301
This media is still thicker than High Resolution Paper with a glossy printing surface to
produce printouts close to photograph quality.
■ Loading
• Load the paper with the whiter side facing up.
• Set the Paper Thickness Lever to the left.
• A maximum of 10 sheets can be loaded at once.
Paper Thickness Lever
Print Side
(Whiter Side)
Glossy Photo Paper GP-301
98
Printing Media
■ Printer Driver Settings
• [Media Type]: Glossy Photo Paper
• [Page Size]:
Ensure the setting matches the size set in the application.
■ Handling of Printed Output
• Do not stack more than 10 sheets in the paper output tray.
• Do not touch the printed surface until the ink dries (approx. two minutes).
■ Printable Area
➡ Printing Area
Glossy Photo Paper GP-301
99
Printing Media
High Gloss Photo Film HG-201
This film has an extremely glossy surface, ideal for printing photographs with outstanding
results.
■ Loading
•
•
•
•
Load only one sheet at a time.
Load the film with the cut corner at the upper right.
If the film is curled, flatten it by curling in the opposite direction.
Set the Paper Thickness Lever to the left.
Cut Corner
Paper
Thickness
Lever
High Gloss Photo Film HG-201
100
Printing Media
■ Printer Driver Settings
• [Media Type]: High Gloss Photo Film
• [Page Size]:
Ensure the setting matches the size set in the application.
■ Handling of Printed Output
• Remove each sheet as soon as it is printed.
• Do not touch the printed surface until the ink dries.
■ Printable Area
➡ Printing Area
High Gloss Photo Film HG-201
101
Printing Media
Glossy Photo Cards FM-101
Made of the same material as Glossy Photo Paper GP-301, this photo-size paper is
intended for printing images that cover the entire surface of the card, without a white border.
To take full advantage of FM-101, make the images slightly larger than the area indicated
by the perforations.
■ Loading
•
•
•
•
Load the paper with the glossy side facing up.
Set the Paper Thickness Lever to the left.
A maximum of 20 sheets can be loaded at once.
Do not use the loading support sheet provided with the package.
Paper
Thickness
Lever
Print Side
(Glossy Side)
Glossy Photo Cards FM-101
102
Printing Media
■ Printer Driver Settings
• [Media Type]: Glossy Photo Cards
• [Page Size]:
Canon 101.6 x 152.4 mm (Canon 4 x 6 in)
■ Handling of Printed Output
• Do not stack more than 20 sheets in the paper output tray.
• Do not touch the printed surface until the ink dries (approx. two minutes).
■ Printable Area
➡ Printing Area
Glossy Photo Cards FM-101
103
Printing Media
Photo Paper Pro PR-101
This is thick paper with a treated surface that enhances gloss and provides superior colour
reproduction. It is ideal for printing high quality photographs.
■ Loading
• Load only one sheet at a time.
• Load the paper with the glossier side facing up.
• Set the Paper Thickness Lever to the left.
Paper Thickness Lever
Print Side
(Glossier Side)
Photo Paper Pro PR-101
104
Printing Media
■ Printer Driver Settings
• [Media Type]: Photo Paper Pro
• [Page Size]:
Ensure the setting matches the size set in the application.
■ Handling of Printed Output
• Remove each sheet as soon as it is printed.
• Do not touch the printed surface until the ink dries (approx. 30 minutes).
Colours in dark images may appear indistinct at first, but become clearer after about 30
minutes.
• Images may smudge if you place them in an album before the ink is completely dry. It is
recommended that you allow the ink to dry for 24 hours.
• Do not attempt to dry the ink with a hair dryer or by exposing printed sheets to direct
sunlight.
■ Storing Printed Output
• Do not store or display printouts in hot, damp or humid conditions.
Never expose them to heat or direct sunlight.
• Store printouts in photo albums, photo frames or presentation binders to protect them
from direct exposure to air or sunlight.
• Do not mount printouts in an adhesive-type album, as you may not be able to remove
them.
• Be aware that some types of clear plastic folders and albums may cause the edges of
the paper to turn yellow.
Photo Paper Pro PR-101
105
Printing Media
■ Printable Area
➡ Printing Area
Photo Paper Pro PR-101
106
Printing Media
Photo Paper Pro PC-101S
Made of the same material as Photo Paper Pro PR-101, this photo-size paper is intended
for printing images that cover the entire surface of the card, without a white border. To take
full advantage of PC-101S, make the images slightly larger than the area indicated by the
perforations. This paper is ideal for printing high quality photographs.
■ Loading
• Load the paper with the glossy side facing up.
• Set the Paper Thickness Lever to the left.
• A maximum of 20 sheets can be loaded at once.
Paper
Thickness
Lever
Glossy Side
Photo Paper Pro PC-101S
107
Printing Media
■ Printer Driver Settings
• [Media Type]: Photo Paper Pro
• [Page Size]:
Select [Custom Size] and enter 118.6 x 215.9mm (4.67 x 8.5 in).
■ Applications Settings
Enter 109.6 x 160.4mm (4.31 x 6.31 in) in [Image Size].
For details on how to specify the image size, refer to the application’s user manual. You
may not be able to specify the size of the image correctly in some applications.
■ Handling of Printed Output
Follow the instructions described in "Photo Paper Pro PR-101".
■ Printable Area
➡ Printing Area
Photo Paper Pro PC-101S
108
Printing Media
Transparencies CF-102
This film is ideal for printing presentation material for use with overhead projectors.
■ Loading
• Place one sheet of plain A4 or Letter paper under the transparencies in the sheet
feeder.
• Set the Paper Thickness Lever to the left.
• A maximum of 30 sheets can be loaded at once.
Paper Thickness
Lever
Plain Paper
Transparencies
Transparencies CF-102
109
Printing Media
• Although you can print on either side of CF-102, best results can be obtained by
printing on the side toward which it curls when held by the edge.
Print Side
■ Printer Driver Settings
• [Media Type]: Transparency
• [Page Size]:
Ensure the setting matches the size set in the application.
■ Handling of Printed Output
• Remove each transparency as soon as it is printed.
• Do not touch the printed surface until the ink dries (approx. 15 minutes).
■ Printable Area
➡ Printing Area
Transparencies CF-102
110
Printing Media
T-Shirt Transfers TR-201
This paper is used to produce iron-on transfers. The image is printed backwards when
[Media Type] is set to T-Shirt Transfer in the printer driver.
Note
➤
For the customers in the United States, refer to the Quick Start Guide for
instructions on using TR-101 T-shirt transfers.
■ Loading
•
•
•
•
Load only one sheet at a time.
If the T-shirt transfer is curled, flatten it by curling it in the opposite direction.
Load the paper with the side that does not have green lines facing up.
Set the Paper Thickness Lever to the right.
Paper Thickness Lever
T-Shirt Transfers TR-201
111
Printing Media
■ Printer Driver Settings
• [Media Type]: T-Shirt Transfer
• [Page Size]:
Ensure the setting matches the size set in the application.
■ Handling of Printed Output
• Remove each T-shirt transfer as soon as it is printed.
• The T-shirt transfer should be used as soon as possible. Refer to the supplied
instructions for details on how to use the paper.
■ Printable Area
➡ Printing Area
T-Shirt Transfers TR-201
112
Printing Media
Banner Paper
This is long paper that consists of consecutive sheets of A4 or Letter size paper, ideal for
printing long posters or banners (up to six sheets long).
■ Preparation for Printing
• When tearing the banner paper, tear off one more sheet than you actually need to print.
• The maximum length for one print job is six sheets, so if you will be printing on six
sheets, tear off a seven-sheet length.
■ Loading
1
Set the Paper Thickness Lever to the right.
2
Load the banner paper with the printing side facing up. Gently fold the
perforation between the first and second sheets.
Leave the rest of the paper folded up.
Banner Paper
113
Printing Media
3
Place the printer where the printed banner output can hang over the edge
of the table.
Ensure the ink does not stain the table or floor.
Banner Paper
114
Printing Media
■ Printer Driver Settings
• [Media Type]: Plain Paper ([Banner Paper] in Windows 2000 or Windows NT4.0)
• [Page Size]:
When using A4 banner paper: A4
When using letter size banner paper: Letter
• [Copies]:
Must be set to "1" to print correctly.
• In Windows 95, Windows 98 or Windows Me, select [Banner Printing] for [Printing Type]
on the [Page Setup] tab.
• On a Macintosh, before creating the document, select [Banner Printing] in the [Page
Setup] dialog box.
■ Printable Area
➡ Printing Area
Banner Paper
115
Troubleshooting
Troubleshooting
• Cannot Install the Printer Driver
• Print Quality is Poor or Contains Errors
• Printer Does Not Start or Stops During Print Jobs
• Paper Does Not Feed Properly or Paper Jams
• The POWER Lamp Flashes Orange
• An Error Message is Displayed on the Screen
• Problems Unique to Windows
Windows
• Problems Unique to the Macintosh
Macintosh
116
Troubleshooting
Cannot Install the Printer Driver
■ Follow the installation procedure correctly.
Install the printer driver carefully following the procedures described in the Quick Start
Guide.
If the printer driver was not installed correctly, reinstall it. If you are using Windows,
delete the printer driver before reinstalling it.
➡ Uninstalling Printer Drivers
Note
➤
If the Installer was forcibly terminated due to an error in Windows, Windows
may be unstable and this will prevent the printer driver from being installed.
Restart the computer before reinstalling the printer driver.
■ Close any other applications before installation.
Sometimes the printer driver cannot be installed because another application is running.
Cannot Install the Printer Driver
117
Troubleshooting
■ If the Installer for the printer driver does not start up automatically when you insert
the Setup Software & User’s Guide CD-ROM, open the [My Computer] window, and
then double-click the CD-ROM icon.
Windows
Note
➤
If you are typing in the file name, you must specify the CD-ROM drive letter
and the installation program ("MSetup.exe"). The CD-ROM drive letter is
computer dependent.
■ Confirm that there are no problems with the Setup Software & User’s Guide CDROM.
In Windows, use Windows Explorer to ensure that the CD-ROM can be read. In a
Macintosh, check that the CD-ROM icon is visible. If there is a problem with the CDROM, contact a Canon service representative.
Cannot Install the Printer Driver
118
Troubleshooting
Print Quality is Poor or Contains Errors
• Cannot Print to End of Job
• Colours are Unclear
• Meaningless Characters or Symbols are Printed
• Printing is Blurred/Colours are Wrong
• Straight Lines are Misaligned
• Printed Paper Curls or Ink Blots
• Back of Paper is Smudged
• Printed Surface is Scratched
• White Streaks
• Colours are Uneven or Streaked
Print Quality is Poor or Contains Errors
119
Troubleshooting
Cannot Print to End of Job
■ Confirm the Page Size setting matches the size of the paper loaded in the printer.
First, check the Page Size setting in the application.
Then check the [Page Size] setting in the Printer Properties dialog box for Windows or
the Page Setup dialog box for Macintosh.
Note
➤
When using an ECP printer port in Windows, you may not be able to print
due to the computer environment. For details, refer to "Problems Unique to
Windows".
■ Check the amount of free space on the hard disk.
You may need to increase the amount of free space by deleting any unnecessary files.
Print Quality is Poor or Contains Errors
120
Troubleshooting
Colours are Unclear
■ Confirm the Media Type setting in the printer driver matches the type of paper
loaded in the printer.
If you are printing a photograph or an illustration from a Windows environment, also
increase [Print Quality] on the [Main] tab.
If you are working in a Macintosh environment, select the [Photo] or [Graphic] icon for
the [Print Mode] in the Print dialog box.
■ Confirm the specified ink tank is installed.
When an ink tank runs out of ink, replace it with a new one.
Note
➤
Printed colours may not match screen colours perfectly due to basic
differences in the methods used to produce colours. Colour control settings
and environmental differences can also affect how colours appear on the
screen.
Print Quality is Poor or Contains Errors
121
Troubleshooting
Meaningless Characters or Symbols are Printed
■ If the problem only occurs when printing a specific document, try editing the
document and then printing it.
If this does not resolve the problem, there may be a problem with your application
program.
Print Quality is Poor or Contains Errors
122
Troubleshooting
Printing is Blurred/Colours are Wrong
■ If a specific colour does not print, check whether the corresponding ink tank is
empty. Replace if necessary.
■ Print the nozzle check pattern to ensure that ink is output correctly.
If the nozzle check pattern does not print correctly, clean the print head.
➡ Printing the Nozzle Check Pattern
➡ Print Head Cleaning
If the problem is not resolved after cleaning the print head several times, the print head
may be worn out. Contact a Canon service representative.
Note
➤
Always ensure you dispose of the protective cap and protective tape from a
print head.
■ Ensure you are printing on the correct side of the media.
You can only print on one side of certain media.
Print Quality is Poor or Contains Errors
123
Troubleshooting
Straight Lines are Misaligned
■ Align the print head.
Ensure you align the print head every time you install a new print head.
Windows
1
Open the Printer Properties dialog box.
2
Click the [Maintenance] tab.
3
Click [Print Head Alignment].
Follow the instructions on the screen.
Print Quality is Poor or Contains Errors
124
Troubleshooting
Macintosh
1
Open the Page Setup dialog box.
2
Click [Utilities].
3
Select [Test Print] from the pull-down menu, and then click [Print Head
Alignment].
Follow the instructions on the screen.
Note
➤
Straight lines can become misaligned if the paper thickness lever has been
moved. Aligning the print head may also resolve this problem.
■ Remove the print head and then reinstall it correctly.
After reinstalling the print head, ensure you align it.
Print Quality is Poor or Contains Errors
125
Troubleshooting
■ In the printer driver settings, select a higher print quality setting.
Windows
1
Open the Printer Properties dialog box.
2
On the [Main] tab, click [High] for the [Print Quality] setting.
Macintosh
1
Open the Print dialog box.
2
For [Print Mode], select [Manual] and then click [Details].
3
Click the [Quality] icon and then drag the [Print Quality] slide bar to the
[Fine] end.
Print Quality is Poor or Contains Errors
126
Troubleshooting
Printed Paper Curls or Ink Blots
■ Use high resolution paper or photo paper to print images that require a lot of ink,
(i.e. pictures with intense colours or photographs).
■ Reduce the [Intensity] setting in the printer driver and try printing again.
Windows
1
Open the Printer Properties dialog box.
2
On the [Main] tab, select [Manual] for [Colour Adjustment], and then click
[Set].
3
Drag the [Intensity] slide bar to adjust the intensity.
Print Quality is Poor or Contains Errors
127
Troubleshooting
Macintosh
1
Open the Print dialog box.
2
For [Print Mode], select [Manual] and then click [Details].
3
Click the [Colour] icon and then drag the [Intensity] slide bar to set the
intensity.
Print Quality is Poor or Contains Errors
128
Troubleshooting
Back of Paper is Smudged
■ If the next page prints before the ink is dry, enable the [Pause Page] printer driver
setting.
You can either remove each printed sheet from the output tray as soon as it is printed,
or enable [Pause Page] to pause after each sheet has printed.
Windows
1
Open the Printer Properties dialog box.
2
Click the [Maintenance] tab.
3
Click [Custom Settings] to open the Custom Setting dialog box.
4
Select [Pause Page], and then click [Send].
Print Quality is Poor or Contains Errors
129
Troubleshooting
Macintosh
1
Open the Page Setup dialog box.
2
Click the [Utilities] button.
3
Select [Custom Settings] form the pull-down menu.
4
Select [Pause between pages.], and then click [Send].
Print Quality is Poor or Contains Errors
130
Troubleshooting
Printed Surface is Scratched
■ Ensure you are using suitable paper.
• The paper weight must be less than 105 g/m2 (28 lb).
If you use paper heavier than 105 g/m2 (28 lb), the print head may scratch the printed
surface.
Clean the print head first and print with the correct paper.
• The paper must not be curled.
This problem can be resolved by simply turning the paper over.
■ When printing on thick paper, set the paper thickness lever to the "
" mark.
This widens a gap between the print head and the paper. If the paper is scratched even
when printing on plain paper, also try this.
■ Reduce the [Intensity] setting in the printer driver and try printing again.
When printing an image with high intensity, especially on plain paper, the paper may
absorb too much ink and become wavy. This may cause the printed surface to become
scratched.
Print Quality is Poor or Contains Errors
131
Troubleshooting
Windows
1
Open the Printer Properties dialog box.
2
On the [Main] tab, select [Manual] for [Colour Adjustment], and then click
[Set].
3
Drag the [Intensity] slide bar to adjust the intensity.
Macintosh
1
Open the Print dialog box.
2
For [Print Mode], select [Manual] and then click [Details].
3
Click the [Colour] icon and drag the [Intensity] slide bar to set the intensity.
■ Ensure you are printing within the recommended printing area.
➡
Printing Area
Print Quality is Poor or Contains Errors
132
Troubleshooting
White Streaks
■ Print the nozzle check pattern to check the ink output.
If a specific colour does not print in the nozzle check pattern, clean the print head.
➡ Printing the Nozzle Check Pattern
➡ Print Head Cleaning
The problem can also be resolved by aligning the print head. For details on print head
alignment, refer to "Straight Lines are Misaligned".
Print Quality is Poor or Contains Errors
133
Troubleshooting
Colours are Uneven or Streaked
■ Increase the print quality setting in the printer driver settings.
Windows
1
Open the Printer Properties dialog box.
2
On the [Main] tab, click [High] for the [Print Quality] setting.
Macintosh
1
Open the Print dialog box.
2
For [Print Mode], select [Manual] and then click [Details].
3
Click the [Quality] icon and then drag the [Print Quality] slide bar to the
[Fine] end.
Print Quality is Poor or Contains Errors
134
Troubleshooting
■ Set the halftoning method to [Diffusion] in the printer driver settings.
Windows
1
Open the Printer Properties dialog box.
2
On the [Main] tab, select [Custom] for the [Print Quality] setting, and click
[Set].
3
Click [Diffusion] for the [Halftoning] setting.
Macintosh
1
Open the Print dialog box.
2
For [Print Mode], select [Manual] and then click [Details].
3
Click the [Quality] icon and then click [Diffusion] for the [Halftoning] setting.
Print Quality is Poor or Contains Errors
135
Troubleshooting
Printer Does Not Start or Stops During Print Jobs
• Printing Does Not Start
• Printing Stops Before It is Completed
• Printer Moves But Does Not Print
• Print Head Holder Does Not Move to the Centre
Printer Does Not Start or Stops During Print Jobs
136
Troubleshooting
Printing Does Not Start
■ Emsure the printer is turned on.
If the POWER lamp is off, press the POWER button.
If the POWER lamp is flashing green, the printer is initialising. Wait until the POWER
lamp stops flashing.
Note
➤
When printing a large amount of data such as a photo or graphics, it takes
longer than usual to begin printing. While the POWER lamp is flashing, the
computer processes the data and sends it to the printer. Simply wait until
the processing is completed.
■ Ensure the printer is securely connected to the computer.
Note
➤
If you are using a switch box or other device, remove and reconnect the
printer directly to the computer. Try printing again.
If printing is now successful, there may be a problem with the device.
Also there could be a problem with the cable(s). Replace the cable(s) and
try printing again.
Printer Does Not Start or Stops During Print Jobs
137
Troubleshooting
■ Ensure the correct printer driver is selected.
In Windows, ensure that [Canon S600] / [Canon S630] is selected in the [Print] dialog
box.
In Macintosh, ensure that [S600] / [S630] is selected in the [Chooser].
Note
➤
In Windows, you can set the Canon S600/S630 as the default printer.
■ Ensure the printer port is set correctly.
Windows
If using a parallel interface printer cable, set "LPT1" as the printer port.
If using a USB cable, set "USBPRNnn" or "USBnnn" ("n" represents a number) as the
printer port.
1
Open the Printer Properties dialog box from the [Start] menu.
➡ Opening the Printer Properties dialog box directly from the [Start]
menu
2
Click the [Details] tab (or [Ports] tab) and set the printer port.
Printer Does Not Start or Stops During Print Jobs
138
Troubleshooting
Printing Stops Before It is Completed
■ Check the status of the POWER lamp.
When the POWER lamp is flashing green, the printer is processing data. Printing a large
amount of data such as a photo or graphics takes time for the computer to process the
data, during which the printer may appear to not be functioning.
In addition, when continuously printing material that uses a large amount of black ink on
plain paper, the printer will sometimes pause. In either case, simply wait until the
processing is completed.
■ Halt the print job and turn the printer off for at least 15 minutes to cool the print
head down.
The print head can overheat when continuously printing for long time. To protect the print
head, the printer will sometimes pause automatically at a line break before resuming.
In this event, interrupt the print job at a convenient time and turn the printer off for at least
15 minutes.
Furthermore, when continuously printing graphics or photos with intense colours,
printing may stop to protect the print head. In this case, printing will not resume. Turn the
printer off and wait for at least 15 minutes.
Caution ➤
Inside the printer, the area around the print head can become extremely
hot. Do not touch the print head or nearby components.
Printer Does Not Start or Stops During Print Jobs
139
Troubleshooting
Printer Moves But Does Not Print
■ Check the ink tanks. If empty, replace them.
■ Ensure that the ink tanks snap into place when you install them.
■ If there is plenty of ink but the printer does not print, clean the print head.
After cleaning the print head, print the nozzle check pattern to check that ink is being
output normally.
➡ Print Head Cleaning
➡ Printing the Nozzle Check Pattern
If the problem is not resolved by cleaning the print head several times, the print head may
be worn out. Contact a Canon service facility.
■ Check the protective tape has been removed from the print head.
Ensure that you align the print head after removing the tape and reinstalling the print
head.
For details on print head alignment, refer to "Straight Lines are Misaligned".
Printer Does Not Start or Stops During Print Jobs
140
Troubleshooting
Print Head Holder Does Not Move to the Centre
■ Ensure the printer is turned on.
The print head holder will not move unless the power is on. If the POWER lamp is off,
close the front cover and turn the power on.
If the POWER lamp is flashing green, the printer is initialising.
When the POWER lamp stops flashing, open the front cover again.
■ If the front cover has been left open for a while, close and reopen it.
If the front cover is left open for more than 10 minutes, the print head holder moves to the
right to prevent the print head from drying out. Close and reopen the front cover to return
the holder to the centre.
Printer Does Not Start or Stops During Print Jobs
141
Troubleshooting
Paper Does Not Feed Properly or Paper Jams
• Paper Does Not Feed Properly
• Paper Jams
Paper Does Not Feed Properly or Paper Jams
142
Troubleshooting
Paper Does Not Feed Properly
■ Confirm the paper conditions.
• The paper is not too thick (less than 105g/m2 / 28 lb).
• The number of sheets loaded does not exceed the recommended level.
• The paper is not creased, curled or wrinkled.
➡ Compatible Media Types
■ Ensure that the left edge of the paper just touches the paper guide.
■ When printing envelopes, refer to "Envelopes" in "Printing Media," and prepare
the envelopes before printing.
Once you have prepared the envelopes, load them in the printer in portrait orientation. If
the envelopes are placed in landscape orientation, they may not feed properly.
■ When using transparencies, load one sheet of plain paper in the printer first, and
then place the transparencies on top of it.
The last transparency may not feed properly unless there is a sheet of plain paper
beneath it.
Paper Does Not Feed Properly or Paper Jams
143
Troubleshooting
Paper Jams
Remove the paper according to the following procedure.
1
Slowly pull the paper out, either from the sheet feeder or from the paper
output slot, whichever is easier.
If the paper tears and a piece remains inside the printer, open the front
cover and remove it.
If you cannot pull the paper out, press the POWER button twice to eject the
paper automatically.
Note
2
After removing all paper, close the front cover.
3
Reload the paper into the printer and press the RESUME/CANCEL button.
➤
When reloading the paper into the printer, refer to "Paper Does Not Feed
Properly" to confirm that you are using the correct paper and are loading it
into the printer correctly.
Paper Does Not Feed Properly or Paper Jams
144
Troubleshooting
The POWER Lamp Flashes Orange
An error has occurred in the printer. The number of flashes indicates the type of error, as
outlined below. Check the cause and take the appropriate action.
■ Two flashes: Out of paper, paper jam or paper feed error
Replace the paper correctly and press the RESUME/CANCEL button.
If paper has jammed in the printer, clear the jam and press the RESUME/CANCEL
button.
■ Three flashes: Paper jam
If paper has jammed in the printer, clear the jam, replace the paper in the printer
correctly and press the RESUME/CANCEL button.
➡ Paper Jams
■ Four flashes: Empty ink tank
One of the ink tanks is empty. Replace it.
➡ Replacing an Ink Tank
The POWER Lamp Flashes Orange
145
Troubleshooting
■ Six flashes: No print head installed
Install a print head.
■ Seven flashes: Defective print head
Remove and reinstall the print head.
Also, ensure that the protective tape has been removed. If reinstalling the print head
does not resolve the problem, replace it with a new one.
■ Eight flashes: Waste ink tank almost full
The printer has a built-in waste ink tank for the ink used during print head cleaning. Eight
flashes indicates that the waste ink tank is nearly full. Press the RESUME/CANCEL
button to cancel the error so you can continue printing. Before the waste ink tank
becomes completely full, contact a Canon service representative to have the waste ink
tank replaced.
Note
➤
Canon recommends to call for service as soon as this error occurs. Once
the waste ink tank becomes completely full, printing will be no longer
possible.
The POWER Lamp Flashes Orange
146
Troubleshooting
■ POWER lamp flashes alternate green and orange:
An error that requires contacting a Canon service representative may have
occurred.
Turn the printer off and unplug the printer from the power supply. Plug the printer back in
and turn the printer back on.
If the problem remains, contact a Canon service representative.
The POWER Lamp Flashes Orange
147
Troubleshooting
An Error Message is Displayed on the Screen
• Error Writing to LPT1 or USBxxx
Windows
• Application Error or General Protection Fault
• Other Error Messages
Windows
• Other Error Messages
Macintosh
Windows
An Error Message is Displayed on the Screen
148
Troubleshooting
Error Writing to LPT1 or USBxxx
Windows
■ Ensure the printer is turned on.
If the POWER lamp is off, turn the printer on.
If the POWER lamp is flashing green, the printer is initialising. Wait until the POWER
lamp stops flashing.
■ Ensure the printer is securely connected to the computer.
Note
➤
If you are using a switch box or other devices, remove and reconnect the
printer directly to the computer and try printing again.
If printing is now successful, there may be a problem with the device.
Also there could be a problem with the cable(s). Replace the cable(s) and
try printing again.
■ If spooling is enabled, disable it to send the print data directly to the printer and try
printing again.
1
Open the Printer Properties dialog box from the [Start] menu.
➡ Opening the Printer Properties dialog box directly from the [Start]
menu
An Error Message is Displayed on the Screen
149
Troubleshooting
2
On the [Details] tab, click [Spool Settings] and then select [Print directly to
printer].
In Windows 2000 or Windows NT4.0, click the [Advanced] tab or
[Scheduling] tab and then click [Print directly to the printer].
■ Verify the printer port status.
• When using the parallel interface (in Windows 95/Windows 98/Windows Me/Windows
2000)
1
Right-click [My Computer] and select [Properties].
2
Click the [Device Manager] tab.
In Windows 2000, click the [Hardware] tab, then click [Device Manager...].
3
Double-click [Ports (COM/LPT)], and then double-click [Printer Port
(LPT1)*].
* The printer port name depends on your system environment.
4
On the [General] tab, check for any indication of a problem with the port
and if the connected device is available.
An Error Message is Displayed on the Screen
150
Troubleshooting
5
Click the [Resources] tab, and check the [Conflicting device list]. An error is
generated if there are any device conflicts. If necessary, delete any
conflicting devices. For details on how to delete a device, refer to the
instruction manual for that device.
• When using the USB interface (in Windows 98/Windows Me)
1
Right-click [My Computer] and select [Properties].
2
On the [Device Manager] tab, double-click [Universal serial bus controller],
and then double-click [Canon S600] / [Canon S630].
3
On the [General] tab, check for any indication of a problem with the device.
If an error has occurred, follow the instruction of "Notes on Handling the
USB Interface (for Windows Users)" in the Quick Start Guide.
■ Ensure that the printer port setting corresponds to the printer interface
connection.
Open the Printer Properties dialog box from the [Start] menu, and click the [Details] tab
(or [Ports] tab). If [LPT1:(ECP Printer Port)] is displayed in the [Print to the following port]
field, the parallel port is selected. If [USBPRNnn (Canon Snnn)] or [USBnnn (Canon
Snnn)] ("n" represents a number) is displayed, the USB port is selected.
An Error Message is Displayed on the Screen
151
Troubleshooting
➡ Opening the Printer Properties dialog box directly from the [Start]
menu
If the setting is incorrect, shut down Windows, turn off the printer and either connect the
printer to the interface selected in the printer driver, or install the correct printer driver
corresponding to the interface.
■ There may be a problem in the printer driver. Uninstall the printer driver and
reinstall it.
➡ Uninstalling Printer Drivers
If the printer is connected to the USB interface, follow the procedure “Notes on Handling
the USB Interface (for Windows Users)” in the Quick Start Guide.
■ If the WPS driver or CAPT driver is installed, either uninstall it or change the driver
port to [FILE] as follows.
1
Click the [Start] button, then click [Settings] and [Printers].
2
Display the WPS or CAPT driver properties, and click the [Details] tab.
3
Change the [Print to the following port] field to [FILE].
An Error Message is Displayed on the Screen
152
Troubleshooting
Application Error or General Protection Fault
Windows
■ Ensure the application program you are using is intended for your operating
system.
For example, if you attempt to print with a Windows 3.1 application under Windows 98,
the application may not function correctly and an error may occur.
Use an application program intended for your operating system.
■ If other applications are running, close them to increase available memory and try
printing again.
■ Ensure that enough memory is allocated to the application.
Refer to the memory requirements of your application.
An Error Message is Displayed on the Screen
153
Troubleshooting
■ Check the amount of free space on the hard disk.
You may need to increase the amount of free space by deleting any unnecessary files.
■ If the problem only occurs when printing a specific document, try editing the
document and then printing it.
If this resolves the problem, there may have been a problem in the original document. If
the same problem occurs with the edited document, contact the manufacturer of your
application.
■ There may be a problem in the printer driver. Uninstall the printer driver and
reinstall it.
If the printer is connected to the USB interface, follow the procedure “Notes on Handling
the USB Interface (for Windows Users)” in the Quick Start Guide.
➡ Uninstalling Printer Drivers
An Error Message is Displayed on the Screen
154
Troubleshooting
Other Error Messages
Windows
■ If the BJ Status Monitor is displayed, follow the instructions on screen.
If an error occurs during printing, the BJ Status Monitor displays the error on the [Printer
Status] tab. Follow the instructions on screen.
In Windows 95, Windows 98 or Windows Me, click the [Guide] tab for action to be taken
in response to the error.
An Error Message is Displayed on the Screen
155
Troubleshooting
■ If one of the following messages is displayed outside of the BJ Status Monitor:
Could not spool successfully due to insufficient disk space
Increase the amount of free space on the disk by deleting any unnecessary files.
Could not spool successfully due to insufficient memory
Increase available memory by closing any other applications currently running.
Printer driver could not be found
Uninstall the printer driver and reinstall it.
➡ Uninstalling Printer Drivers
Background printing failed (Windows 95/Windows 98/Windows Me only)
Restart Windows and try printing again.
Could not print [application name] – [file name]
Try printing again once the current job is finished.
An Error Message is Displayed on the Screen
156
Troubleshooting
Other Error Messages
Macintosh
■ If a message with the format "Error No.: Xn" (where "X" represents a letter and "n"
represents a number) is displayed:
Error No.: X202
Not enough memory for printing. Increase available memory by closing any other
applications currently running.
Error No.: X203
There is a problem with the printer driver. Uninstall the printer driver and reinstall it.
➡
Uninstalling Printer Drivers
Error No.: X300
Ensure the power is on, and that the printer and the computer are securely connected. If
the problem remains, verify the Chooser setting.
1
In the Apple menu, select [Chooser].
2
Click the S600/S630 icon and ensure S600/S630 is selected as the
connected destination.
If it is not selected, select it.
If the problem remains, delete all unnecessary documents from the Extensions and
Control Panels folder.
An Error Message is Displayed on the Screen
157
Troubleshooting
Problems Unique to Windows
Windows
• The BJ Status Monitor is Not Displayed
• Cannot Print in Background (Windows 95/Windows 98/Windows Me only)
• Cannot Print Normally
Problems Unique to Windows
158
Troubleshooting
The BJ Status Monitor is Not Displayed
■ Ensure "Enable bi-directional support for this printer" is selected.
1
Open the Printer Properties dialog box from the [Start] menu.
➡ Opening the Printer Properties dialog box directly from the [Start]
menu
2
On the [Details] tab (or [Ports] tab), click [Spool Settings] and select
"Enable bi-directional support for this printer."
■ If the printer is connected to the parallel interface, ensure the printer cable
supports bi-directional communication.
The BJ Status Monitor is displayed only when the computer and cable support bidirectional communication. If you do not know whether your computer and printer cable
support bi-directional communication, contact your dealer or computer manufacturer.
Problems Unique to Windows
159
Troubleshooting
Cannot Print in Background (Windows 95/Windows 98/
Windows Me only)
■ Check the amount of free space on the hard disk.
Background printing requires a certain amount of disk space. You may need to delete
unnecessary files, or disable background printing.
■ Ensure that background printing is enabled.
1
Open the Printer Properties dialog box.
➡ Opening the Printer Properties Dialog Box
2
On the [Page Setup] tab, click [Printer control...] and select [Background
Printing].
Problems Unique to Windows
160
Troubleshooting
Cannot Print Normally
■ When the printer port is set to "ECP", cancel ECP mode and then try printing
again.
Sometimes ECP mode disrupts normal printing.
1
Open the Printer Properties dialog box.
2
Click the [Maintenance] tab.
3
Click [Custom Settings] to open the Custom Setting dialog box.
4
Clear the [Set printer to ECP mode] check box, and then click [Send].
5
Turn the printer off and back on again.
Problems Unique to Windows
161
Troubleshooting
■ If the WPS driver or CAPT driver is installed, either uninstall it or change the driver
port to [FILE] as follows.
The WPS (Windows Printing System) driver or CAPT (Canon Advanced Printing
Technology) driver may disrupt normal printing.
1
Click the [Start] button, then click [Settings] and [Printers].
2
Display the WPS or CAPT driver properties, and click the [Details] tab.
3
Change the [Print to the following port] field to [FILE].
Problems Unique to Windows
162
Troubleshooting
Problems Unique to the Macintosh
Macintosh
• Jagged Text or Graphics, or Banded Gradations
• Cannot Print in Background
Problems Unique to the Macintosh
163
Troubleshooting
Jagged Text or Graphics, or Banded Gradations
■ Ensure your application supports Quick Draw.
If you are using a PostScript-compatible application, printed text and lines may appear
jagged and gradations may appear banded. As S600/S630 is not a PostScript printer but
a Quick Draw printer, use an application compatible with Quick Draw for printing.
Problems Unique to the Macintosh
164
Troubleshooting
Cannot Print in Background
■ Ensure background printing is enabled.
1
In the Apple menu, select [Chooser].
2
Click [Backgrounding] on.
■ Check the amount of free space on the hard disk.
Background printing requires a certain amount of disk space.
You may need to remove unnecessary files, or disable background printing.
Problems Unique to the Macintosh
165
Appendices
Appendices
• Deleting an Unknown Device (USB interface)
• For Faster Printing
Windows
Windows
Macintosh
169
Appendices
Deleting an Unknown Device (USB interface)
Windows
If printer driver installation using the USB interface was not seccessful, carry out the
procedure described in “Notes on Handling the USB interface (for Windows Users)” in the
Quick Start Guide.
If the problem remains, follow the steps below to delete the unknown device.
1
Click the [Start] button, select [Settings] and click [Control Panel].
2
Double-click [System].
3
Click the [Device Manager] tab.
In Windows 2000, click the [Hardware] tab, then click [Device Manager...].
4
Select the name of the printer or ‘Unknown device’ and click [Remove].
In Windows 2000, click the unknown device, then click [Uninstall] in the
[Action] menu.
Caution ➤
Be careful not to remove any other device. Windows may not function
properly if another device is incorrectly deleted.
Deleting an Unknown Device (USB interface)
170
Appendices
• If the unknown device is under [Universal serial bus controller]
• If the unknown device is under [Other devices]
Deleting an Unknown Device (USB interface)
171
Appendices
5
When the confirmation message appears, click [OK].
6
Click [Close] to close the [System Properties] window.
In Windows 2000, click
window.
and then click [OK] in the [System Properties]
7
Click
8
Turn the printer off.
9
Remove the Setup Software & User’s Guide CD-ROM, if it is in the drive.
10
Restart Windows.
11
Install the printer driver again following the instructions in the Quick Start
Guide.
at the top right of the [Control Panel] window to close it.
Deleting an Unknown Device (USB interface)
172
Appendices
Windows
For Faster Printing
The USB interface provides the quickest printing with Windows 98, Window Me and
Windows 2000. Refer to the Quick Start Guide for USB connection details.
When using the parallel printer interface, use the ECP data transfer mode for faster printing.
Note
Note
➤
The ECP mode may not speed up printing on some computers.
1
To enable the ECP mode, first confirm the following:
• The printer and computer are connected with a parallel printer cable.
• The printer driver has been installed.
• The printer port of the computer supports the ECP mode.
• The parallel port is set to ECP mode in the BIOS settings.
➤
Refer to your computer manual for details on printer port specifications and
BIOS settings.
2
Open the Printer Properties dialog box from the [Start] menu.
➡ Opening the Printer Properties dialog box directly from the [Start]
menu
For Faster Printing
173
Appendices
3
Click the [Maintenance] tab and click the [Custom Settings] icon.
4
Select the [Set printer to ECP mode] check box and click [Send].
For Faster Printing
174
Appendices
Note
➤
• Some computers may have problems printing in the ECP mode.
In this case, clear the [Set printer to ECP mode] check box in the screen
above, and click [Send]. Turn the printer off and back on to cancel the
ECP mode.
• With Windows 95, a problem may remain after you cancel the ECP mode
setting. See also “Unable to Print from the Canon BJ Printer Port” in the
on-line Help.
For Faster Printing
175
Specifications
Specifications
Printing method:
Bubble Jet on-demand
Printing resolution:
2400 (horizontal) × 1200 (vertical) dpi. max.
Print speed (printing with Canon standard pattern):
Black printing
Fast:
15 ppm (S600) / 17 ppm (S630)
Normal:
11 ppm
Colour printing
Fast:
10 ppm (S600) / 12 ppm (S630)
Normal:
4.3 ppm
Print direction:
Bi-directional
Print width:
203.2 mm max. (8.0 in)
Resident print control mode:
Canon extended mode
173
Specifications
Receive buffer:
62 KB
Interface (parallel):
IEEE 1284-compatible
Interface (USB):
USB 1.10-compatible
Interface connector (parallel):
Amphenol 57-40360 or equivalent
Interface connector (USB):
USB standard Series B receptacle (USB interface)
Recommended printer cable (parallel):
Material:
AWG28 or larger
Type:
Twisted-pair shielded cable
Length:
Up to 2.0 m (6.5 ft)
Connectors: Amphenol 30360 or equivalent
Recommended printer cable (USB):
Material:
AWG28 (data wiring pair) or AWG20 to 28 (distribution pair)
Type:
Twisted-pair shielded cable
Length:
Up to 5.0 m (16.4 ft)
Connectors: USB standard Series B pluggable
174
Specifications
Acoustic noise level:
Approx. 39 dB (A) (in the highest print quality mode)
Operating environment:
Temperature: 5 to 35˚C (41 to 95˚F)
Humidity:
10 to 90%RH (no condensation)
Storage environment:
Temperature: 0 to 35˚C (32 to 95˚F)
Humidity:
5 to 90% RH (no condensation)
Power supply:
Europe
AC 230 V±10%, 50 Hz
USA/Canada AC 120 V, 60 Hz
Australia
AC 240 V, 50 Hz
Power consumption:
Standby:
Printing:
3W
33 W
Dimensions (without a paper rest and paper output tray):
430 (W) × 294 (D) × 177 mm (H)
16.93 (W) × 11.57 (D) × 6.97 in (H)
Weight:
Approx. 5 kg (11 lb.)
175
Specifications
■ Feed method:
Continuous feed through auto sheet feeder
For Plain Paper, Envelopes, High Resolution Paper,
Glossy Photo Paper, High Gloss Photo Film,
Glossy Photo Cards, Photo Paper Pro,
Transparencies, T-shirt Transfers, Banner Paper
■ Sheet feeder capacity:
Plain Paper (75 gsm)
High Resolution Paper
Envelopes
Glossy Photo Paper
High Gloss Photo Film
Glossy Photo Cards
Photo Paper Pro PR-101
Photo Paper Pro PC-101S
Transparencies
T-Shirt Transfers
Banner Paper
100 sheets max.
80 sheets max.
10 pieces max.
10 sheets max.
1 sheet
20 sheets max.
1 sheet
20 sheets max.
30 sheets max.
1 sheet
1 sheet
176
Specifications
■ Ordinary print media:
Regular size:
A4, A5, B5, Letter, Legal, European DL, US Com.#10
Custom size:
width: 90.0 to 215.9 mm (3.54 to 8.5 in)
height: 120.0 to 584.2mm (4.72 to 23.0 in)
Weight:
64 to 105 g/m2 (17 to 28 lb)
Canon Special media:
High Resolution Paper
Glossy Photo Paper
High Gloss Photo Film
Glossy Photo Cards
Photo Paper Pro
Photo Paper Pro
Transparencies
T-Shirt Transfers
Banner Paper
HR-101N
GP-301
HG-201
FM-101
PR-101
PC-101S
CF-102
TR-201
177
Specifications
■ Graphic image printing:
Data format:
Canon extended mode: Raster image format
Resolution:
Canon extended mode: 300, 600, 1200, 2400 dpi
■ Print Head:
Black:
320 nozzles (600 dpi)
Cyan, Magenta, Yellow: 256 nozzles (1200 dpi)
■ Ink Tanks:
Capacity:
Black(BCI-3eBK)
Cyan(BCI-3eC)
Magenta(BCI-3eM)
Yellow(BCI-3eY)
approx. 695*1, approx. 1250*2
approx. 460*2
approx. 395*2
approx. 300*2
*1 1500 characters per page, normal text, at standard and plain paper mode with
Windows 95/Windows 98/Windows Me
*2 Based on printing the ISO JIS-SCID No.5 pattern at standard and plain paper
mode with Windows 95/Windows 98/Windows Me
178
Specifications
■ Printer driver operating environment:
IBM PC/AT-compatible computer running on Windows 95, Windows 98, Windows
Me, Windows NT 4.0, Windows 2000 or Macintosh computers with USB interface
running on Mac OS 8.1 or later
■ Hard disk space:
Approx. 12 MB to install on Windows 95, Windows 98 and Windows Me, 21 MB on
Mac OS, or approx. 25 MB on Windows NT 4.0 and Windows 2000 (including
temporary files)
Note
➤
• BJ Status Monitor cannot be used when printer is used in network
operating environment.
• When connecting printer and computer through USB interface, use the
system under the following operating environment.
Windows
Computer with Microsoft Windows 98 or Windows Me, which is preinstalled
by a computer manufacturer on purchase. (USB port operation also needs
to be assured by the manufacturer.)
Macintosh
Macintosh computers with USB and Mac OS 8.1 or later, which is
preinstalled by a computer manufacturer on purchase. (When using an
iMac running under Mac OS 8.1, the system must be upgraded using iMac
Firmware 1.0, which can be downloaded from the home page of Apple
Computer, Inc.)
Specifications subject to change without prior notice.
179
Specifications
■ Printing Area
To ensure the best print quality, the printer allows a margin along each edge of
media.
Printing area (dark blue): Canon recommends that you print within this area.
(
)
Printable area (light blue): The area where it is possible to print. However, printing
in this area can adversely affect the print quality or the
)
paper feed precision. (
➡A4, B5, A5
➡Letter, Legal
➡Glossy Photo Cards
➡Photo Paper Pro (PC-101S)
➡Envelopes
➡Banner Paper
180
Specifications
A4, B5, A5
Size
Printable Area (width x height)
A4
203.2 × 289.0 mm / 8.0 × 11.4 in
B5
175.2 × 249.0 mm / 6.9 × 9.8 in
A5
141.2 × 202.0 mm / 5.6 × 7.9 in
3.0 mm / 0.12 in
28.0 mm / 1.1 in
Recommended printing area
Printable area
5.0 mm / 0.2 in
3.4 mm / 0.13 in
26.5 mm / 1.04 in
3.4 mm / 0.13 in
181
Specifications
Letter, Legal
Size
Printable Area (width x height)
Letter
203.2 × 271.4 mm / 8.0 × 10.7 in
Legal
203.2 × 347.6 mm / 8.0 × 13.7 in
3.0 mm / 0.12 in
28.0 mm / 1.1 in
Recommended printing area
Printable area
5.0 mm / 0.2 in
6.4 mm / 0.25 in
26.5 mm / 1.04 in
6.3 mm / 0.25 in
182
Specifications
Glossy Photo Cards
Size
Printable Area (width x height)
Glossy Photo Card
109.4 × 159.9 mm / 4.3 × 6.3 in
28.0 mm / 1.1 in
Recommended printing area
(Printable area is the same.)
26.0 mm / 1.02 in
5.1 mm / 0.2 in
4.1 mm / 0.16 in
183
Specifications
Photo Paper Pro (PC-101S)
Note
Size
Printable Area (width x height)
Photo Paper Pro PC-101S
109.6 × 160.4 mm / 4.3 × 6.3 in
➤
The printing area of Photo Paper Pro PR-101 is identical to that of A4 size
paper. For details, refer to "A4, B5, A5".
28.0 mm / 1.1 in
Recommended printing area
(Printable area is the same.)
28.0 mm / 1.1 in
4.0 mm / 0.16 in
4.0 mm / 0.16 in
184
Specifications
Envelopes
Size
Printable Area (width x height)
European DL
190.5 × 103.2 mm / 7.5 × 4.1 in
US Com. #10
211.8 × 98.0 mm / 8.3 × 3.9 in
3.4 mm / 0.13 in
Printable area
3.4 mm / 0.13 in
3.0 mm / 0.12 in
26.5 mm / 1.04 in
185
Specifications
Banner Paper
Size
Printable Area (width x height)
Banner Paper
A4: 203.2 × 1774.0 mm / 8.0 × 69.8 in
Letter: 203.2 × 1668.4 mm / 8.0 × 65.7 in
28.0 mm / 1.1 in
3.0 mm / 0.12 in
5.0 mm / 0.2 in
3.4 mm / 0.13 in
3.4 mm / 0.13 in
Min. 2 sheets
Max. 6 sheets
Recommended printing area
Printable area
186
Index
Index
A
Application Error
153
B
Background printing (Macintosh)
Background printing (Windows)
Banner Paper
BCI-3eBK
BCI-3eC
BCI-3eM
BCI-3eY
BJ Print Monitor (Macintosh)
BJ Status Monitor (Macintosh)
BJ Status Monitor (Windows)
59
160
113
69
69
69
69
59
65
37, 155, 159
C
Cancelling a Print Job (Macintosh)
Cancelling a Print Job (Windows)
CAPT driver
Chooser (Macintosh)
Cleaning
61
40
152, 162
59
35, 46, 78
190
Index
Cleaning the Printer
Client (Macintosh)
Compatible Media Types
83
63
90
D
Deep Cleaning
Deleting an Unknown Device (USB interface)
35, 81
167
E
ECP mode
Envelopes
Error Message
170
92
148, 155, 157
F
Front cover
15, 141
G
Gamma Correction (Macintosh)
General Protection Fault
Glossy Photo Cards FM-101
Glossy Photo Paper GP-301
55
153
102
98
High Gloss Photo Film HG-201
High Resolution Paper HR-101N
100
96
H
I
Ink Tank
68, 69
191
Index
M
Media Type (Macintosh)
Media Type (Windows)
48
23
Network (Macintosh)
Nozzle Check Pattern
62
77
Opening the Printer Properties Dialog Box (Windows)
20
N
O
P
[Page Setup] Dialog Box (Macintosh)
Page Size (Windows)
Paper feed roller
Paper Guide
Paper Jams
Paper Output Tray
Paper Rest
Paper Size (Macintosh)
Paper Thickness Lever
Photo Optimizer PRO (Macintosh)
Photo Optimizer PRO (Windows)
Photo Paper Pro PC-101S
Photo Paper Pro PR-101
PICT File (Macintosh)
POWER Button
POWER Lamp
44
25
94
15
144
15
15
44
17
51
32
107
104
56
18
18, 145
192
Index
Print Advisor (Windows)
[Print] Dialog Box (Macintosh)
Print Head Holder
Print Head Lock Lever
Print Mode (Macintosh)
Print server (Macintosh)
Printable area
Printer Driver (Macintosh)
Printer Driver (Windows)
Printer port
Printer Port (Parallel)
Printer Properties Dialog Box (Windows)
Printing Area
Printing the Nozzle Check Pattern
24
48
17
17
48
62
180
42
19
150, 151
16
20, 22
180
74
R
Replacing an Ink Tank
RESUME/CANCEL Button
69
18
S
Sheet Feeder
Simulate illustration (Macintosh)
Simulate Illustration (Windows)
Specifications
15
52
31
173
Transparencies CF-102
Transporting the Printer
109
85
T
193
Index
T-Shirt Transfers TR-201
111
Uninstalling Printer Drivers (Macintosh)
Uninstalling Printer Drivers (Windows)
USB interface
USB Port
66
41
167
16
U
W
When to Replace Ink Tank and Maintain Print Head
WPS driver
68
152, 162
194