DRIFT Ghost-s User manual
advertisement
P R O F E S S I O N A L H D A C T I O N C A M E R A S
DRIFT GHOST-S
USER MANUAL
W W W . D R I F T I N N O V A T I O N . C O M
V E R S I O N : 1 . 0 . 0
Contents
Precautions
Overview
Using The Camera
Initial Setup
Powering On and Off
Charging
Formatting a Micro SD Card
Selecting a Micro SD Card
Camera Menu System
Video Mode
Recording Video
Video Tagging
Simultaneous Photos and Videos
Video Mode Settings
Video Tagging
Car DVR
Bit Rate
Scene Mode
Photo Mode
Capturing Photos
Photo Settings
Scene Mode
Timelapse Mode
Capturing Timelapse Sequences
Timelapse Settings
Scene Mode
Photoburst Mode
Capturing Photoburst Sequences
Photoburst Settings
Scene Mode
Playback
Video Playback
Viewing Photos
Viewing Timelapse
Viewing Photoburst
Deleting Files
Camera Settings
Wi-Fi
Date and Time
Camera Settings Profiles
Firmware
Clone Mode
/
14
/
15
/
3
/
4
/
5
/
8
/
9
/
10
/
/
6
7
/
11
/
12
The Two-Way Remote Control
Powering On and Off
Pairing Camera to Remote One to One
Using the Remote Control One to One
Pairing Cameras to Remote One to All
Using the Remote Control One to All
Shot Setup
Fixing the Camera to the Universal Clip
Mounting the Camera to a Drift Mount
Lens Rotation
Zoom
Connectivity
Connecting to Windows PC
Connecting to Mac
Connecting to a TV
Connecting to a Wi-Fi Device
Manual HDMI Out
System Requirements
Conserving Battery
Updating Firmware
Camera Care
Cleaning the Camera
Cleaning the Lens and LCD Screen
Cleaning the Seals
Anti-Fog Care
Technical Specifications
Warranty
Disclosures
/
16
/
17
/
18
/
19
/
20
/
21
/
22
/
23
/
24
/
25
/
13
2
Precautions
General Precautions
Please take note of the following guidelines when using your Ghost-S camera:
• The camera is 2m shock resistant, but not shock proof—please take care of your camera and accessories, mounting and storing them securely.
• For your safety, do not press the buttons on the camera during sports activities.
• Do not store the camera anywhere prone to dust or damp for extended periods of time.
• Do not leave the camera exposed to extremely high temperatures—such as under direct sunlight—for extended periods of time as this may affect the camera housing and internal components.
• Clean the lens and screen with a micro fibre, antistatic cloth to remove fingerprints or dust—no cleaning chemicals are required.
• The camera has a working temperature range of -10°C to 40°C (14°F to 104°F).
• Power off the camera before removing the battery or memory card—the memory card and stored data may be damaged if it is removed or inserted while the camera is powered on.
• Remove the battery and memory card before storing the camera for long periods of time.
Weather Resistance
The Ghost-S is engineered to withstand dust, snow, rain, splashes and submersion up to 3m for 30 minutes at a time.
• Operating the camera at temperatures below 0°C reduces battery life and lowers battery performance.
• Do not charge the battery at temperatures below 0°C.
• Do not leave the camera submerged for longer than 30 minutes.
• Clean off any salt water or dirt from the camera immediately and prior to storing.
• Do not subject the camera to a sudden impact of water—the camera should always be used in the waterproof case when in intensive water-based applications.
• Always use the universal clip as a rear hatch key to ensure the camera is sealed tightly to ensure full water proofing. (See figure 1)
• The camera is only 3m waterproof when the STANDARD rear hatch is used and fitted properly as shown below.
Attention
!
Rechargeable batteries are only to be charged under adult supervision
!
DO NOT short-circuit the battery terminals
!
DO NOT open, puncture or otherwise damage the rechargeable battery, or dispose of it in fire
Optimal Camera Storage
We recommend users store cameras for a minimum of 6-12 hours with the
Back Hatch open, Battery Hatch open and the Battery removed in less then
30% humidity to help dry out anti-fog inserts regulary.
Avoid opening the Back Hatch in damp or humid conditions.
Disclaimer
Drift Innovation will not, under any circumstances, be responsible for injuries or property damaged incurred during participation of any high-risk sport or activity not endorsed or recommended by Drift Innovation.
Remember that the warranty will only cover manufacturing defects.
Figure 1: Universal Clip as Rear Hatch key
3
Overview
Figure 2: Top View
Figure 3: Screen View
Figure 4: Connector View
MENU Button (Video Tag/
Simultaneous Photo)
LEFT Button (Zoom Out)
RIGHT Button (Zoom In)
ACTION Button (On/Off/Rec/Stop)
Camera LED Indicator
2.0” LCD Screen
300° Rotating/Replaceable Lens
¼”-20 Thread
Speaker
HDMI Port (Mini Type C)
USB Port (Mini Type B)
Battery Slot Cover
Micro SD Card Slot
3.5mm Microphone Input
Standard Rear Hatch
Rear Hatch ‘Up’ Indicator
Lens ‘Up’ Indicator
Built-in Noise Reducing Microphone
Figure 5: Rear View - No Hatch Figure 6: Rear View - Standard Hatch Figure 7: Front View
4
Using The Camera
Figure 8: Inserting the Battery and Micro SD Card
Initial Setup
1. Unscrew the rear hatch of the camera by hand, or by using the notch in the
Universal Clip (anti-clockwise movement).
2. Slide the catch and open the battery slot cover, insert the battery as above and close the cover.
3. Insert a micro SD card into the card slot, as above, until you hear a click.
4. Connect the camera by the mini USB cable (provided) to a powered USB port and charge for 4 hours before first use.
5. Replace the rear hatch, ensuring the arrow indicator points to the camera face with the control buttons.
6. Connect the Two-Way Remote Control by the mini USB cable (provided) to a powered USB port and charge for 2 hours, or until remote LED indicator lights turn green before first use.
Powering On and Off
Press and hold the ACTION button on the camera—the camera LED indicator and screen will power on and display a welcome message.
To power off, hold the ACTION button for 3 seconds, or until the camera LED indicator and screen power off.
Charging
1. Ensure the battery is inside the camera and the camera is powered off.
2. Connect the mini USB cable to the port at the rear of the camera and then to a powered USB port in your computer, other USB device or USB power adaptor (not included).
!
If connected to a computer, the camera screen will show a USB symbol.
!
If connected to a USB power adaptor, the screen will show ‘Charging...’.
3. A full charge takes around 4 hours (min 1A)—once the camera is fully charged, remove the mini USB cable and replace the rear hatch and screw closed.
Battery Life
At a temperature of 25°C (77°F), with all power saving features off and the camera recording continuously, the battery will last for about 3.5 hours (1080p 30FPS,
Wi-Fi off, normal bit rate) on a full charge (see Conserving Battery Life, p20).
Using an External Power Supply
The camera can be powered by an external power supply such as a USB power adaptor, Drift Power Pack or Drift 12V Charger. We recommend you to power off your camera before plugging your camera to any external power supply.
Press the ACTION button to begin normal usage when using an external power supply. If the external power is cut off for any reason during recording, the camera will immediately start drawing power from the rechargeable battery instead and continue recording, protecting your footage from file corruption.
Selecting a Micro SD Card
The Drift Ghost-S is compatible with
Micro SD, SDHC or SDXC cards up to
64GB. We recommend Class 10 cards for recording HD video and system stability.
Below is a table of approximate video recording times against card size in normal bit rate mode.
1 GB
2 GB
4 GB
8 GB
16 GB
32 GB
64 GB
Approximate Recording Time (30 FPS)
1080P 720P WVGA
9min
18min
12min
24min
27min
54min
36min
1h 12min
2h 24min
4h 48min
9h 36min
48min
1h 36min
3h 12min
6h 24min
1h 48min
3h 36min
7h 12min
14h 24min
12h 48min 28h 48min
Formatting a Micro SD Card
Formatting will remove all files from a memory card. When using a new card for the first time, always format the memory card using the camera. With the card inserted in the camera:
1. Open the Main Menu (see p6) and select ‘Camera Settings’.
2. Select ‘Format Memory Card’, press
ACTION and then confirm.
Formatting may take a few moments to complete—please be patient.
Removing a Micro SD Card
To remove the card, push it until you hear a click. The card slot is spring loaded and the card will slide from the slot.
5
Camera Menu System
MENU Button (Tag/Back)
LEFT Button (Zoom Out)
RIGHT Button (Zoom In)
ACTION Button (On/Off/Rec/Stop)
Camera LED Indicator
Figure 9: Ghost-S Top View
The Drift Ghost-S has an easy-to-use menu system which can be navigated using the camera’s four control buttons.
Main Menu (Figure 10)
To open the Main Menu, press MENU while the camera is powered on. The Main
Menu screen will display the four menu options.
Use LEFT and RIGHT to navigate between the menu options. A highlighted option will show a green icon instead of red. To select a highlighted menu option, press ACTION and a sub-menu will open.
! To go back a step, at any time, press MENU.
Mode Selection Menu (Figure 11)
The Mode Selection menu is used to select the camera recording mode.
On opening the Mode Selection menu, the screen will display the four camera mode icons. Move between the different camera modes using LEFT and RIGHT.
To select a highlighted camera mode, press ACTION. The screen will return to
Live Preview for the selected mode and the camera is ready to capture media.
For more information about the four camera modes, see p7-12.
Mode Settings Menu (Figure 12)
The Mode Settings menu is used to view and edit settings for each of the four camera modes.
On opening the Mode Settings menu, the screen will display the four camera mode icons. To select a highlighted camera mode, press ACTION. A further submenu will open, listing adjustable settings for the selected camera mode. Use
LEFT and RIGHT to navigate between settings. Use ACTION to edit and confirm settings; LEFT and RIGHT to adjust setting values.
For more information about the four camera modes and their settings, see p7-12.
Playback Menu (Figure 13)
The Playback menu is used to view video and images for each of the four camera modes.
For full details, see p13.
Camera Settings Menu
The Camera Settings menu is used to view and adjust camera settings.
For full details, see p14.
Mode Selection Playback
Mode Settings Camera Settings
Figure 10: Main Menu
Video Mode Photo Mode
Timelapse Mode Photoburst Mode
Figure 11: Mode Selection Menu
Video Settings Photo Settings
Timelapse Settings Photoburst Settings
Figure 12: Mode Settings Menu
Video Playback Photo Playback
Timelapse Playback Photoburst Playback
Figure 13: Playback Menu
6
Video Mode
Video Mode (GREEN LED)
While the camera is powered on and in Video Mode—with a micro SD card inserted with enough free memory—it will record video when ACTION is pressed on the camera or the remote control.
1. To enter Video Mode, ensure the camera is powered on.
2. Press MENU to enter the Main Menu.
3. Open the Mode Selection menu, highlight Video Mode and press ACTION.
The screen will return to Live Preview and display the Video Mode icon @ in the top-lefthand corner of the screen, the camera LED will turn green—the camera is ready to record video.
Recording Video
1. Press ACTION on the camera or remote control to begin recording video.
2. The camera LED indicator will blink red while the camera is recording.
3. To stop recording, press ACTION on the camera, or STOP on the remote control—the camera LED indicator will turn green.
!
The duration of the current recording is indicated by the on-screen timer.
!
For best performance always use, at minimum, a class 10 Micro SD card.
Taking Simultaneous Photos While Recording Video
Pressing MENU on the camera (or ACTION on the remote control) while recording video will simultaneously take a still photo. Taking a simultaneous photo will result in an 8MP photo if the Ghost-S is recording at 30 or 25fps in any resolution. If you are recording in 48, 50 or 60fps, the Ghost-S will create a 2MP simultaneous photo.
! This feature is not active for frame rates higher than 60fps.
!
This feature is only available when Video Tagging (see p8) is turned off.
Video Mode
Scene Mode / Bit Rate
SD Card / Battery Indicator
HB
Video Mode Settings
Resolution
Frame Rate
Field Of View
Exposure
Self Timer
Video Tagging
Video Tagging
Interval
Car DVR Mode
Car DVR Interval
Bit Rate
Scene Mode
Default Settings
1m
2m
5m
On
Manual
Off
1m
3m
5m
10m
Normal
High
Normal
Vivid
Low Light
Yes
Cancel
10s
On
Off
10s
30s
+2
Off
3s
5s
1080P
960P
720P
WVGA
25 (1080/960/720/WVGA)
30 (1080/960/720/WVGA)
48 (960)
50 (1080/960 / 720/WVGA)
60 (1080/960 720/WVGA)
100 (720/WVGA)
120 (720/WVGA)
200 (WVGA)
240 (WVGA)
160° (1080/960/720/WVGA)
127° (1080)
90° (1080)
-2
-1
0
+1
00:00:00
Video Resolution
Frame Rate
Field Of View
Exposure
Record Timer
Figure 14: Video Mode Live Preview Screen
7
Video Tagging
Video Mode (cont’d)
Figure 15: Video Tagging Graphic Representation
When activated, this feature allows the camera to continuously record video, but save only ‘tagged’ footage. For example, with Video Tagging turned on and a Video Tagging Interval of 30s selected, pressing MENU while recording video will save the previous 30s, current 30s and an additional 30s—a total of 1m30s of tagged footage.
Video Tagging can be turned on or off in the Video Settings menu .
1. To turn Video Tagging on, switch to Video Settings Menu.
2. Cycle to ‘Video Tagging’, press ACTION to toggle between On/Off.
3. Under ‘Video Tagging Interval‘, press ACTION to choose the desired interval time.
4. Now when you press ACTION from the live preview screen, the camera LED will BLINK GREEN, and you are now recording in video tagging mode, without saving the footage. This is also shown by the TAG icon rectangle being RED.
5. While recording video, press MODE on the camera (or ACTION from the remote) to tag a video—the camera LED will begin to BLINK RED while a tagged interval is being saved. This is also shown by the TAG icon rectangle turning GREEN.
6. Tagging can be stopped by pressing ACTION on the camera, or STOP on the remote control. This will change the camera LED from blinking RED, to solid
RED.
7. Once the three video tagging intervals are saved, the camera will automatically return to recording without saving, until commanded to stop by pressing the ACTION button.
In the event that you require extending your video to be sure you do not miss any critical shots, pressing ACTION again while in a tagging session (LED blinking
GREEN) will add an additional tagging interval to the end of the saved footage.
! Please ensure you have at least 4GB of free space on your micro SD card for video tagging to function properly.
! Activating Video Tagging will disable accessibility to Car DVR mode.
8
Video Mode (cont’d)
Car DVR mode
ENGINE STARTS
START RECORDING New clip New clip New clip
ENGINE STOPS
STOP RECORDING
Camera turns on
(Automatically)
CAR DVR INTERVAL* CAR DVR INTERVAL CAR DVR INTERVAL
Figure 16: Car DVR Graphic Representation
Camera turns off
(Automatically)
Car DVR mode can be turned on or off in the Video Settings menu
This hands off mode setting is ideal for insurance and security purposes. In this mode the camera records footage in a continuous loop style (Car DVR Intervals) recording loop after loop until it fills the Micro SD Card. Once full, the oldest loops will be deleted as the newest ones are saved. DVR loop intervals can be 1min, 3min, 5min and 10min.
Car DVR mode can be turned on or off in the Camera Settings menu, it will automatically power the camera on and begin recording when power is delivered to the USB port. Setting the Car DVR to ‘M’ (manual) allows the user to use this feature while manually starting the first loop by pressing ACTION. This is ideal for users such as cyclists, where external power is not frequently used.
1. To turn Car DVR mode on, open Video Mode Settings from the Main Menu and select Car DVR, press ACTION, then select ‘ON’, or ‘M’ for manual mode. On the live preview screen a CAR icon will indicate that Car DVR mode is enabled.
Bit Rate
Users can select to keep the normal compression used by the H.264 codec, or if they prefer, allow a higher flow of data for preserving more of the original recording. This will increase the bit rate used in all recording modes. The maximum bit rate is set to 35.0 Mbps, this is reserved for the most processor intensive recording modes of 720p 120/100, WVGA
240/200. In High Bit Rate, 1080p 60/50 will be approximately 26.0 Mbps versus 18.0 Mbps in Normal Bit Rate.
Scene Mode
Normal: Use this as your ‘go to’ setting. This is the default setting and will give you the most neutral, true colour palette possible for the broadest range of environments, and is the best mode to choose for bright outdoor environments.
Vivid: Use this mode when you are intentionally looking to make your colours a touch more saturated.
Low Light: This setting should only be used in low light settings such as filming at night or indoors with less ambient lighting. If the camera is set to 60/50fps in any resolution, auto slow shutter mode will regulate the frame rate from
60/50fps to 30/25fps based on the luminance in order to achieve the highest exposure rate possible for each frame.
In this instance, each frame will be printed twice in order to keep the overall frame rate at 60/50fps.
9
Photo Mode
PHOTO MODE (YELLOW LED)
While the camera is powered on and in Photo Mode—with a Micro SD card inserted with available memory—it will capture a 5, 8 or 12MP still image when
ACTION is pressed on the camera or the remote control.
1. To enter Photo Mode, ensure the camera is powered on.
2. Press MENU to enter the Main Menu.
3. Open the Mode Selection menu, highlight Photo Mode and press ACTION.
The screen will return to Live Preview and will display the Photo Mode icon @ in the top-left corner of the screen, and the camera LED will turn YELLOW. The camera is ready to take photos.
Capturing photos
1. Press ACTION on the camera or remote control to take a photo.
2. The LED indicator will BLINK RED once before returning to YELLOW.
Scene Mode
Normal: Use this as your ‘go to’ setting. This is the default setting and will give you the most neutral, true to reality colour palette possible for the broadest range of environments, and is the best mode to choose for bright sunny days.
Vivid: Use this mode when you are intentionally looking to make your colours a touch more saturated.
Low Light: This setting should only be used in low light settings such as filming at night or indoors with less ambient lighting. This will optimise the camera to reduce image noise in low light settings.
Photo Mode Settings
Resolution
Field Of View
Exposure
Self Timer
Scene Mode
Default Settings
Off
3s
5s
10s
Normal
Vivid
Low Light
Yes
Cancel
12MP
8MP
5MP
160°
127°
90°
-2
-1
0
+1
+2
Scene Mode
Photo Mode SD Card / Battery Indicator
45%
000000
Photo Resolution
Field of View Angle
Exposure
Photos Taken
Figure 17: Photo Mode Live Preview
10
Timelapse Mode
Timelapse Mode (PURPLE LED)
While the camera is powered on and in Timelapse Mode—with a Micro SD card inserted with enough free memory—it will capture a series of still images at a specified rate when ACTION is pressed on the camera or the remote control.
1. To enter Timelapse Mode, ensure the camera is powered on.
2. Press MENU to enter the Main Menu.
3. Open the Mode Selection menu, highlight Timelapse Mode and press
ACTION.
The screen will return to Live Preview and will display the Timelapse Mode icon
@ camera is ready to take timelapse photos.
Capturing Timelapse Sequences
The Timelapse Sequence Interval can be set from the Mode Settings menu.
1. Open Mode Settings from the Main Menu and select Timelapse Mode.
2. Under ‘Sequence Interval’, choose the desired interval time and press ACTION to confirm.
3. Return to Live Preview and press ACTION on the camera or remote control to start timelapse.
4. The camera LED will BLINK RED once when each photo is taken.
5. To stop timelapse, press ACTION on the camera or STOP on the remote control.
! in the top-left corner of the screen. The camera LED will turn purple—the
The Ghost-S will not render the timelapse still images into a video, you must insert the still sequences produced by the Ghost-S into third party postproduction software in order to render a timelapse video.
Timelapse Mode Settings
Resolution
Field Of View
Exposure
Sequence Interval
Self Timer
Scene Mode
Default Settings
10s
30s
1m
Off
3s
+2
0.5s
1s
2s
3s
5s
12MP
8MP
5MP
160°
127°
90°
-2
-1
0
+1
5s
10s
Normal
Vivid
Low Light
Yes
Cancel
Scene Mode
Timelapse Mode
Scene Mode
Normal: Use this as your ‘go to’ setting. This is the default setting and will give you the most neutral, true to reality colour palette possible for the broadest range of environments, and is the best mode to choose for bright sunny days.
SD / Battery Indicator
67%
Vivid: Use this mode when you are intentionally looking to make your colours a touch more saturated.
Low Light: This setting should only be used in low light settings such as filming at night or indoors with less ambient lighting. This will optimise the camera to reduce image noise in low light settings.
000000
Photo Resolution
Field of View Angle
Exposure
Sequence Interval
Photos Captured
Figure 18: Timelapse Mode Live Preview
11
Photoburst Mode
Photoburst Mode (CYAN BLUE LED)
While the camera is powered on and in Photoburst Mode—with a Micro SD card inserted with enough free memory—it will capture a burst of still images for an allotted duration, at a specified rate when ACTION is pressed on the camera or the remote control.
1. To enter Photoburst Mode, ensure the camera is powered on.
2. Press MENU to enter the Main Menu.
3. Open the Mode Selection menu, select Photoburst Mode and press ACTION.
The screen will return to Live Preview and will display the Photoburst Mode icon @ in the top-left corner of the screen. The camera LED indicator will turn
CYAN (light blue)—the camera is ready to take a photoburst series.
Capturing Photoburst Sequences
The Photoburst Mode settings can be set from the Mode Settings menu.
1. Open Mode Settings from the Main Menu and select Photoburst Mode.
2. Under ‘Capture Rate’, highlight the desired photo capture rate and press
ACTION to confirm.
3. Under ‘Burst Duration’, highlight the desired duration and press ACTION to confirm.
4. Return to Live Preview and press ACTION on the camera or remote control to start photoburst.
5. The camera LED indicator will BLINK RED once when each photo is taken, and return to CYAN (light blue) once the file is saved and ready to shoot another photoburst.
! The Ghost-S does not automatically make composite images from the photoburst sequence shot. This can be done on third party post-production software.
Photoburst Mode Settings
Resolution
FOV
Capture Rate
FOV
Exposure
Self Timer
Scene Mode
Default Settings
160°
127°
90°
-2
-1
0
+1
+2
12MP
8MP
5MP
160°
127°
90°
5/s
10/s
20/s
30/s
Off
3s
5s
10s
Normal
Vivid
Low Light
Yes
Cancel
Resolution Capture Rate Burst Duration
1s
12MP
10/s
5/s 1s 2s
Scene Mode
Normal: Use this as your ‘go to’ setting. This is the default setting and will give you the most neutral, true to reality colour palette possible for the broadest range of environments, and is the best mode to choose for bright sunny days.
8MP
10/s
5/s
30/s
1s
1s
2s
2s
1s
5s
5s
Vivid: Use this mode when you are intentionally looking to make your colours a touch more saturated.
Low Light: This setting should only be used in low light settings such as filming at night or indoors with less ambient lighting. This will optimise the camera to reduce image noise in low light settings.
20/s 1s
5MP
10/s 1s 2s 5s
5/s 1s 2s
Scene Mode
Photoburst Mode SD / Battery Indicator
90%
5s
Photo Resolution
Field of View / Exposure
Capture Rate / Burst Duration
Figure 19: Photoburst Mode Live Preview
12
Playback
On opening Playback from the Main Menu, the screen will display the four camera mode icons. A number will be displayed beside each camera mode icon to indicate how many files are stored on the memory card for each mode.
To select a highlighted camera mode, press ACTION.
The screen will display the most recent video, photo, timelapse or photoburst folder. To move between files, use LEFT and RIGHT. To return to Live Preview, press the menu button to backout.
Video Playback (Figure 21)
1. Select the video file you wish to playback using LEFT/RIGHT, then press
ACTION.
2. The screen will display a sub-menu. Highlight ‘View’ to watch the selected video and press ACTION.
!
Highlight ‘View All’ to watch all the videos stored on the memory card and press ACTION.
3. Pressing ACTION will pause playback and pressing MENU will stop playback.
4. Use LEFT and RIGHT during playback to rewind and fast-forward.
Viewing Photos (Figure 22)
On opening Photo Mode from the Playback menu, the screen will display the most recent photo. To move between photos, use LEFT and RIGHT. Photos are displayed in their native 4:3 format for 12, 8 and 5MP images.
Viewing Timelapse Photos (Figure 23)
On opening Timelapse Mode from the Playback menu, the screen will display the first image in the most recent timelapse sequence. To move between sequences, use LEFT and RIGHT. Press ACTION and select ‘View Series’ to open the desired sequence.
Viewing Photoburst Photos (Figure 24)
On opening Photoburst Mode from the Playback menu, the screen will display the first image in the most recent photoburst sequence. To move between sequences, use LEFT and RIGHT. Press ACTION and select ‘View Series’ to open the desired sequence.
Deleting Files
1. Pressing ACTION while viewing any file in Playback will open a sub-menu.
2. Highlight ‘Delete’ to delete the selected video or photo, or ‘Delete All’ to delete every file for the selected camera mode. Press ACTION and confirm.
3. You can also choose to delete timelapse or photoburst sequences in the same manner as above.
!
Please be aware when using ‘Delete All’ that all files for the selected camera mode will be removed from the memory card and cannot be retrieved.
!
Using this function will not delete any other files from the Micro SD card.
Video Playback Photo Playback
40%
Timelapse Playback Photoburst Playback
Figure 20: Playback Menu
Video Index
Video Playback
0015/0031
00:00:09/00:20:48
Video Resolution
Frame Rate
Playback Timer
Playback Status
Figure 21: Video Mode Playback
Photo Playback
0015/0031
Photo Index
Figure 22: Photo Mode Playback
Timelapse Playback
S0003 0001/0125
Series Index
Timelapse Image Index
Figure 23: Timelapse Mode Playback
Photoburst Playback
S0003 0001/0125
Series Index
Photoburst Image Index
Figure 24: Photoburst Mode Playback
13
Camera Settings
Upon opening Camera Settings from the Main Menu, the screen will display the list of adjustable camera settings.
Use LEFT and RIGHT to move between settings. Use ACTION to edit and confirm settings; LEFT and RIGHT to move between setting values.
Wi-Fi
To turn Wi-Fi on or off, highlight
‘Wi-Fi’ from the Camera Settings menu and press ACTION. While Wi-Fi is on, the Wi-Fi icon @ will show in
Live Preview.
For more about connecting the camera to other Wi-Fi devices, see
p19.
Wi-Fi Network Name
Your camera will create a local area network, with the network name
‘Ghost S XXX’, where ‘XXX’ is any three digit number you wish to assign in this setting. Pressing LEFT/RIGHT will cycle the selected digit value, while pressing
ACTION will move the cursor to the next digit.
Clone Mode
See p15.
Setting the Date and Time
1. Highlight ‘Date’ from the Camera
Settings menu and press ACTION.
2. Adjust the year using LEFT/RIGHT and press ACTION to confirm.
3. Set the month, day and time, pressing ACTION to confirm each.
Wi-Fi
Wi-Fi Network
Name
Clone Mode
Mic Sensitivity
Speaker Volume
LCD Brightness
LCD Off
Remote Control
Remote Pairing
Remote LED
Camera LED
Digital Zoom
Camera Settings Profiles
All camera settings can be saved by selecting ‘Save Settings’ from the
Camera Settings menu and choosing a save profile: ‘A’, ‘B’ or ‘C’.
Settings profiles can be loaded by selecting ‘Load Settings’ from the menu, then ‘A’, ‘B’ or ‘C’.
The camera will power on in the same settings configuration it was powered off in, except for digital zoom, which gets reset.
Camera Off
Reset Default Settings
To restore the factory camera settings, highlight ‘Reset Settings’ from the Camera Settings menu and press ACTION, then confirm.
On
Off
‘000’
Low
Medium
High
Never
5s
10s
20s
1m
5m
On
Off
AP
ST
Off
Low
Med
High
Off
Low
Medium
High
Off
One To One
One To All
On
Off
On
Off
On
Off
Never
1m
2m
5m
HDMI Out
Resolution
HDMI Out
Frame Rate
Date/Time
Date/Time
Stamp
Save Settings
Load Settings
Language
Save Settings
Load Settings
Reset Settings
Format Memory
Card
Firmware Version
AUTO
1080P
1080i
720P
60 FPS
50 FPS
30 FPS
25 FPS
Year/Month/Day
Off
On
Profile A
Profile B
Profile C
A
A
Profile A
Profile B
Profile C
English
Français
Deutsch
Español
Italiano
Português
Russian
Nederlands
Norwegian
Dansk
Polski
Român
Svenskt
ÄŒeský
ελληνικά
B
B
Yes
Cancel
Yes
Cancel
X.X.X.X
C
C
Firmware Version
This will display the camera’s current firmware version. For more details about updating firmware, see p21.
14
Camera Settings (cont’d)
Clone Mode
The ultimate tool for any video production, Drift Innovation’s Clone Mode allows simultaneous recording and synchronized setting adjustments for linked cameras. Users can sync up to five cameras connected to the same
Clone Network via Wi-Fi. Start just one camera and all networked cameras start.
Change the mode on one, and all cameras update to the new mode.
AP
Setting Up Clone Mode
Clone mode works on a ‘Master-Slave’ type of system. There is one main
Access Point (AP) camera; all Station (ST) cameras connect by all having the same SSID (see figure 25).
Setting up the Access Point (AP) Camera
1. Select the first camera for the Clone Network (this can be any camera you wish to be on the network), navigate to ‘Clone Mode’ in the SETTINGS menu.
Press ACTION, and then highlight ‘AP’ to designate this first camera as the
Access Point for your System. Once highlighted, press ACTION to select.
2. On your Access Point camera, set the ‘Wi-Fi Network Name’ to be the number you wish to assign to this Clone Network. This is of your choosing at this point, and can be anything.
3. Next (still on the AP camera) turn on your Wi-Fi, see p14.
ST ST ST
Figure 25: Clone Mode System Overview
ST
Setting up the Station Mode (ST) Camera(s)
At this point your AP camera is already setup (see above) and you are connecting up to four additional cameras in Station Mode to your Clone Mode
Network.
1. Select the next camera you wish to add to your network. Navigate to ‘Clone
Mode’ in the SETTINGS menu. Press ACTION, and then highlight ‘ST’ to
designate this next camera into Station Mode. Once highlighted, press
ACTION to select.
2. On your Station Mode camera, set the ‘Wi-Fi Network Name’ to be
the SAME NUMBER you assigned to the AP camera. Whatever
network name you gave in step two, you must re-enter here for the
cameras to be on the same network.
3. Next (still on this ST camera) turn on your Wi-Fi, see p14.
Repeat steps 4-6 to add up to four Station Mode cameras, making a total network of five cameras including the Access Point camera.
15
Two-Way Remote Control
Powering On and Off
1. Ensure the camera is powered on, see p5.
2. Press and hold the ACTION button on the remote—the LED will power on and indicate the current camera mode.
!
The remote will automatically power off if it does not find a camera after 15s.
Charging
Connect the remote control using the Mini USB cable (provided) to a powered
USB port. The LED will blink red. A full charge takes around two hours using a
1-2A charger. Once the remote is fully charged, the LED will show solid green— remove the mini USB cable and replace the rubber dust-proof USB seal.
Pairing Camera to a Remote Control - One to One
[The camera and remote control included in the package are already paired to one another]
1. On the camera, press MENU, select Camera Settings from the Main Menu and press ACTION.
2. Highlight ‘Remote Pairing’ in the Camera Settings menu and press ACTION.
3. Highlight ‘ ‘ in the Remote Pairing options and press ACTION.
4. Ensure the remote control is powered on.
5. On the remote control, press ACTION — The camera will beep and return to the Camera Settings menu if it has recognised the remote.
!
If the camera does not display ‘successful’ and return to the Camera Settings menu it will not be paired—try pressing ACTION on the remote again.
6. On the camera, the icon beside Remote Pairing will change to indicate it is paired to a remote control.
Using the Remote Control - One to One
While the camera and remote are both powered on and paired, pressing ACTION on the remote control will begin recording video, capture a photo, start timelapse or photoburst, depending on the camera mode.
Pressing ACTION while recording video will capture a photo, or start Video
Tagging (if activated, see p8). Pressing STOP will end video recording or timelapse.
Pressing STOP while the camera is in Live Preview will toggle between camera modes, as indicated by the LED indicator on the camera and remote.
Figure 26: Two Way Remote Control Top View
USB Power In
ACTION Button
STOP/MODE Button
Remote LED Indicators
! The Remote is NOT waterproof, and should not be submerged. It is however weather-resistant, and can withstand rain and snow.
LED Status
Rapid Blinking Red
Blink Red
Blinking Red
Blink Blue
Solid Green
Solid Yellow
Blinking Purple
Blinking Cyan
Blinking White
Description
Low Battery (<15%)
Taking a photo
Recording video
Signal confirmation
Video Mode
Photo Mode
Timelapse Mode
Photoburst Mode
One to All Mode
16
Two-Way Remote Control (cont’d)
Pairing Camera to a Remote Control - One to All
A single remote control can be paired to an infinite number of cameras in a 10m range from the remote control, to enable footage to be captured from every angle.
1. On the cameras, press MENU, select Camera Settings from the Main Menu and press ACTION.
2. Highlight ‘Remote Pairing’ from the Camera Settings menu and press ACTION.
3. Highlight ‘ ‘ in the Remote Pairing options and press ACTION.
4. On the remote control, press ACTION—the camera will display ‘successful’ and return to the Camera Settings menu if it has recognised the remote.
!
Any camera that does not display ‘successful’ and returns to the Camera
Settings menu will not be paired—try pressing ACTION on the remote again.
5. On the camera, the icon beside Remote Pairing will change to indicate it is in
‘‘One to All’’ mode.
! When pairing multiple cameras, always test the remote control to see if it operates all the cameras before mounting them.
Using the Remote Control - One to All
While the camera and remote are both powered on and paired, pressing ACTION on the remote control will begin recording video, capture a photo, start timelapse or photoburst, depending on the camera mode.
Pressing ACTION while recording video will capture a photo, or start Video
Tagging (if activated, see p8). Pressing STOP will end video recording or timelapse.
! The remote control indicator lights will show white to indicate the remote control is paired to multiple cameras.
! Mode changing from the remote control is disabled when in one to all
mode.
17
Shot Setup
Figure 27: Universal Clip Screw Location & Lens Rotation
Fixing the Camera to the Universal Clip
1. Align the screw of the Universal Clip with the thread on the underside of the camera body.
2. Twist the screw thread in a clockwise direction by hand.
3. As the Universal Clip tightens against the body of the camera, rotate the camera to provide the desired angle of attachment, holding the clip in place.
4. Tighten the screw on the Universal Clip until it fits firmly against the camera body.
Closing the Rear Hatch
1. Ensure the directional arrow “up” indicator is pointing up towards the buttons.
2. Use the notch in the Universal Clip to tighten the screw on the Rear Hatch.
! Failure to completely seal the Rear Hatch where water is present may result in
permanent damage to the camera (see p3).
Mounting the Camera to a Drift Mount
Included with the camera are several Drift mounts which will help you find the shot you want.
Mounting the Camera on Goggles
1. Attach the Goggle Mount to the strap of your goggles.
2. Slide the camera (with Universal Clip attached) into the mount until the two arms on the clip click into place, check that the clip is fully secured.
Mounting the Camera on a Helmet
1. Position the Curved Surface Mount against your helmet to find the optimum mounting position.
2. Ensure the mounting surface is clean, dry and free of oil and dust.
3. Remove the cover of the mount’s 3M adhesive and fix the mount to the helmet—allow 24 hours to cure.
4. Slide the camera (with Universal Clip attached) into the mount until the two arms on the clip click into place, check that the clip is fully secured.
Fixing the Camera to the Standard ¼”-20 Thread
Thread the camera onto a tripod, or any other mount with a standard camera thread, turning the camera body on the thread clockwise to secure.
!
However you choose to mount your camera, ensure that the camera is fitted firmly to reduce the risk of losing it. Give it a tug before you set out.
Lens Rotation
In order to maximise your mounting options, the camera lens is rotatable through 300°, allowing for the perfect shot from even the most extreme of positions.
Whilst holding the camera body in one hand, use the index finger and thumb of the other hand to hold the camera lens firmly, then twist the lens to the desired angle. The arrow indicator above the lens indicates ‘up’ and corresponds with the top of the display in Live Preview.
!
Be sure to rotate the lens back to the 0° position (so the ‘up’ indicator on the lens is aligned with the LED indicator on the camera) before mounting, or un-mounting, the camera to reduce the risk of damage to the lens.
Zoom
The Drift Ghost-S includes a 10x digital zoom function that allows you to take close-up photo and video.
While in Live Preview, or while recording video, press and hold the
RIGHT button to zoom in, and the
LEFT button to zoom out.
Digital zoom can be disabled in the general Camera Settings Menu.
18
Connectivity
Recorded video footage and photos can be copied to a computer using the USB cable provided or—if your computer has an appropriate card reader—directly from the Micro SD card.
Connecting to a Windows PC by USB Cable
1. Connect the camera to your PC using the USB cable. The camera screen will display a USB logo and the LED status indicator will blink red.
2. Your PC’s operating system may be setup to open new devices automatically, if not, open My Computer.
3. Your PC should recognise the camera as a removable device—look for DRIFT
CARD in the list of all devices and open.
4. Open the DCIM folder, inside you will find the 100DRIFT folder, which contains all the files saved on the memory card by the camera.
!
If there are a very large numbers of files, there will be multiple folders
(100DRIFT, 101DRIFT, etc).
5. Copy the desired files to your PC.
Connecting to a Mac by USB Cable
1. Connect the camera to your Mac using the USB cable. The camera screen will display a USB logo and the LED status indicator will blink red.
2. Your Mac’s operating system may be setup to open new devices automatically, if not, open a new Finder window.
3. Your Mac should recognise the camera as a removable device—look for DRIFT
CARD in the list of devices and open.
4. Open the DCIM folder—inside, you will find the 100DRIFT folder which contains all the files saved on the memory card by the camera.
!
If there are a very large numbers of files, there will be multiple folders
(100DRIFT, 101DRIFT, etc).
5. Copy the desired files to your Mac.
Connecting the Camera to a TV
1. While the camera is turned off, connect it to your TV using a Mini HDMI type
C cable (not included).
2. Power on the camera.
3. Once booted up, the image usually displayed on the camera’s LCD screen will instead be displayed directly on your TV, and the sound will come out of the
TV speakers.
4. Press MENU to cycle through camera modes while connected to a TV.
Connecting to a Wi-Fi Device
1. Set the Wi-Fi network name and turn on the Wi-Fi as per p14.
2. On your mobile device navigate to your Wi-Fi network settings. For most
devices, this will be found in SETTINGS>Wi-Fi. Search for the network name
‘Ghost S XXX’ where XXX is the three number digit you assigned when setting
up the network name on your camera.
3. Select the network found in step 2 to connect your device and your camera.
Manual HDMI Out
The Ghost-S will automatically connect via HDMI to an HD ready TV. However, it is also capable of manually setting the HDMI out to either 1080p, 1080i or 720p.
These can be set to 60, 50, 30 or 25 frames per second for the progressive modes, and 60 or 50 HZ for the interlaced modes.
Playing Video on a Computer
Some computers may not have the correct codecs required for video playback and editing.
If you experience difficulties playing video recorded with your camera, you can download VLC media player for free from www.videolan.org.
If you are experiencing difficulties editing video or do not wish to use
VLC player for playback, you will need to download and install a codec pack.
The FFDshow codec pack can be downloaded from www.free-codecs.
com/FFDshow_download.htm.
Recommended System Requirements
To smoothly view and edit HD video, powerful hardware is required:
Windows
• 2nd Generation Intel® Core™ or
AMD equivalent, Intel® Core™ i7 recommended.
• Minimum 2GB of RAM (recommend
4GB and up).
• Graphics card comparable to
NVIDIA GeForce 600 or AMD
Radeon HD6000 and up.
• Microsoft Windows Vista or
Windows 7 or later.
Mac
• 2nd Generation Intel® Core™ or
AMD equivalent, Intel® Core™ i7 recommended.
• Minimum 2GB of RAM (recommend
4GB and up).
• Graphics card comparable to
NVIDIA GeForce 600 or AMD
Radeon HD6000 and up.
• Mac OS X v10.5 or later.
19
Conserving Battery
The Ghost-S comes with a rechargeable 1700mAh Lithium-Ion battery, allowing you to record continuously for hours between charges. However, sometimes you may find yourself in a location without a power outlet to charge your camera. If you’re outside, cold conditions can drain battery power at a faster rate than usual.
Fortunately, the Ghost-S comes with a number of features to conserve the battery life. These can all be found in the Camera Settings menu.
LCD Off
The camera’s LCD screen consumes power, so one of the best ways to extend battery life is to use the ‘LCD Off’ feature. By default, LCD screen will automatically power off after 20 seconds (the time interval can be chosen when selecting ‘LCD Off’ from the Camera Settings menu).
The camera will still function as normal when the screen is off: in Live Preview, the camera is ready to record at any time. If recording is in progress, the camera will continue to record. The remote can also be used while the screen is off. The screen can be turned back on again at any time by pressing any button.
Spare batteries
You can also charge a second battery before you set out and then swap it when the first is empty. Spare 1700mAh
Ghost batteries and Power Packs are available from official Drift retailers.
Please visit driftinnovation.com for more information and where to purchase.
!
Always change the battery in a clean, dry and safe environment.
Getting camera batteries wet will damage them and may result in injury. For your own safety, never use damaged batteries.
LCD Brightness
The LCD screen is backlit, this too consumes power. It is possible to reduce the intensity of this light by adjusting the ‘LCD Brightness’ setting in the Camera
Settings menu—you will notice a slight increase in battery life if you use a lower brightness setting.
Camera Auto Off
It is possible to set the camera to power off entirely when no buttons are pressed for a number of minutes (the duration can be chosen selecting ‘Camera Auto
Off’ from the Camera Settings menu). This can be useful to reduce battery consumption if the camera is accidently left powered on.
!
The camera will not power off while recording is in progress. However, once the camera has powered off, you will need to power it on again before capturing any footage.
!
The remote control will not operate the camera while the unit is powered off.
Using Different Video Resolutions
Bigger resolutions as well as higher frame rates all contribute to more ‘work’ for the processor; this means more battery power is required to process the work. If you are shooting video and do not require full 1080p (for instance for easy internet sharing) try using a lower resolution and your battery life will increase accordingly. For example, in 1080p at 30fps you can expect 3h 30min versus 4h 20min in WVGA at 30fps.
20
Updating Firmware
The Drift Ghost-S should always be operated on the latest firmware available, downloadable from www.driftinnovation.com. Be sure to check back often for updates as we will continue to add features and options to your camera after you purchase it
1. Go to www.driftinnovation.com and download the latest firmware file
(‘’Ghost_S.bin’’) found easily in the Drift Ghost-S section, or by navigating to
‘Firmware’ listed in the bottom footer of any page.
2. Plug your Drift Ghost-S unit into your computer (MAC or PC) using the supplied USB cable.
3. Your camera should come up as an External Device with the ‘’Drift Card’’
Micro SD card being visible as a storage device (see connectivity p19). Please copy the ‘’Ghost_S.bin’’ firmware file into the root folder of the ‘’Drift Card’’
Micro SD card.
4. Safely eject your Drift Ghost-S and Micro SD as a storage device from your computer.
5. Power on the camera and wait for it to automatically update itself. You will get a “Firmware Update in Progress” message and the LED status indicator will blink red. This should take a few seconds and the camera will automatically power off after.
6. Power the unit on again.
7. Navigate to the settings menu and check the “Firmware Version” to ensure the firmware has been successfully updated.
!
Your camera might shut off automatically once more after step 6, this is normal.
Simply turn the unit back on. This step is necessary in order to refresh a set of Wi-Fi initialisation code that only needs to be refreshed once per firmware update.
21
Camera Care
The Ghost-S is specifically designed for extreme sports. It is a very durable piece of equipment. However, to ensure a long and healthy life for your camera, please follow the guidelines below.
Cleaning the Camera
During your sporting activities, the camera will inevitably get dirty or wet.
Although this is not an issue, it is recommended that you clean the camera after each use. Clean the camera thoroughly with a damp cloth and let it air dry before you open the back hatch or rotate the lens. Take extra care when cleaning the built-in microphone and speaker.
Cleaning the Lens and LCD Screen
In order to provide a clear image for high definition video, it is important to keep the camera lens clean. Be careful not to scratch the camera lens whilst cleaning it. Wipe off any surface mud or water from the lens with a damp cloth and use a dry, micro fibre, scratch proof cloth to polish the lens once it is dry.
!
Scratch proof cloths are available from any camera shop or optician.
Cleaning the Seals
To ensure that the camera remains waterproof, it may be necessary to occasionally clean the contact surfaces around the rear hatch seal. This can be done by wiping a damp cloth around the seal. Be careful not to leave excessive water on the seal, then let it air dry.
Anti Fog Care
The camera is equipped with anti fog inserts, as well as anti fog treatments for the LCD screen. For the best results always ensure the environment is dry before you open the rear-hatch of the camera to prevent moisture from excessively humid air from being trapped inside the camera. Trapped moisture inside the camera might cause slight condensation to occur. To remove this moisture, store the camera overnight in a cool, dry environment with the battery and rear hatch removed, and the battery latch open.
22
Technical Specifications
Video Resolution 1080p, 960p (4:3), 720p and WVGA (16:9)
File Format
Sensor Type
.MP4 (H.264 codec)
12 MP Sony CMOS sensor with back illuminated technology
Frame Rate
1080P: 25 / 30 / 50 / 60 fps
960p: 25 / 30 / 48 / 50/ 60 fps
720p: 25 / 30 / 50 / 60 / 100/ 120 fps
WVGA: 25 / 30 / 50 / 60 / 100 / 120 / 200 / 240 fps
Field of View
1080p: 90° / 127° / 160°
960p: 160°
720p: 160°
WVGA: 160°
Lens Focal Range 0.5m to infinity
Lens Rotation 300°
Zoom ×10 (digital)
Photo Mode
Exposure
LCD Screen
Waterproof
5 / 8 / 12 megapixels
Auto / Manual (advanced users)
2.0” colour TFT covered in Corning® Gorilla ® Glass
3m (9.84ft)
Microphone Built-in, noise reducing microphone
Built-In Memory 256MB (not user accessible)
Memory Capacity Micro SD memory cards up to 128GB
Inputs 3.5mm external microphone (extension included)
Outputs
Compatibility
Remote Range
HDMI connector type C (cable not included)
USB Plug and Play, mini-B USB connector
Windows Vista or Windows 7 and up / Mac OS X 10.5 and up
10m (32ft)
Radio Frequency 2.4G
Dimensions: 105 (L) × 52 (W) × 33 (D) mm
Camera
Weight: 171g
Power: 1700mAh rechargeable lithium-ion battery
(included) (DC 3.7V)
Remote Control
Dimensions: 59 (L) × 48 (W) × 12 (D) mm
Weight: 22g
Power: 350mAh rechargeable lithium-ion battery
(DC 3.7V)
23
Warranty
Drift Innovation (“Manufacturer”) warrants to the original End User (“Purchaser”) that this product purchased from us or any authorized dealer is free from manufacturing defects in material and workmanship for the applicable warranty period, as set forth in the product specification, or 12 months—whichever is the less. Drift Innovation products purchased from non-authorized dealers might not be covered by the offered warranty. The warranty period is considered valid from the issue date confirmed on the sale invoice.
This limited warranty covers defects encountered in the normal use of the product during the warranty period and does not apply under the following conditions:
• Product is damaged due to physical abuse, mishandling, accident, negligence or failure to follow the supplied operating instructions;
• Product is physically modified by Purchaser in any manner other than that for which it was intended or otherwise previously approved by the Manufacturer;
• Product is damaged or has developed defects caused by the use of unauthorized parts or by an unauthorized repair service;
• The product has been subject to unsuitable operating or physical conditions outside those recommended in product specifications as provided by the
Manufacturer;
• Product has it’s serial numbers altered or removed;
• Product is damaged due to improper packaging of the warranty return to the dealer or Manufacturer.
In the event of a product failure under normal use and within the warranty period, a repair or replacement will be provided at the discretion of the
Manufacturer or the authorized dealer. The Manufacturer warranty does not cover loss, accidental damage or costs incurred during the handling and shipping of repairs or replacement products.
The Manufacturer shall have no liability or responsibility whatsoever to Purchaser or any other person for any loss, injury, death, or any damages derived from the use of the product or accessories.
Service
To obtain our warranty service, register your product at driftinnovation.com.
Customer Support
• Check firmware updates, product updates and user videos.
• We are here to help you make the most of your Ghost-S camera; if you have any suggestions, comments or complaints, please visit the support section of our website— support.driftinnovation.com—or contact our customer support team on [email protected].
24
Disclosures
FCC Information
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and;
2. This device must accept interference received, including interference that may cause undesired operation.
Warning
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by powering the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna;
• Increase the separation between the equipment and the receiver;
• Connect the equipment into an outlet on a circuit different from that which the receiver is connected;
• Consult the dealer or an experienced radio / TV technician for help.
Industry Canada Information
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
1. This device may not cause interference, and;
2. This device must accept any interference, including interference that may cause undesired operation of the device.
This Class [B] digital apparatus complies with Canadian ICES-003.
Cet appareil s’accorde avec Industrie Canada licence-exempte RSS standard.
Son fonctionnement est soumis aux deux conditions suivantes:
1. Cet appareil ne peut pas causer l’intervention, et;
2. Cet appareil doit accepter de l’intervention, y compris l’intervention qui peut causer l’opération non désirée de.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
Cet appareil s’accorde avec Industrie Canada licence-exempte RSS standard.
FCC RADIATION EXPOSURE
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment . This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Motorcycle Disclaimer
Interacting with the camera while riding could cause a crash and you or others may be seriously injured or killed.
• Keep your eyes and mind on the road;
• Avoid looking at the camera while riding;
• Stop the vehicle in a safe location before adjusting the camera.
25
advertisement
Related manuals
advertisement