v2.1 REV. 05/2022
Installer and user’s manual
MONOBLOCO 300
PRE-INSTALLATION INFO
Necessary tools
IMPORTANT
ATTENTION: for your security, don’t open the awning before
N°17
N°19
N°4
N°5
Before the application , check the wall leveling where you
will apply the awning. In case the wall is hollow or curved,
apply chocks to align it correctly.
Wall brackets fixation
No. of wall brackets
Awning dimensions (mm)
WALL
2
3000
AWNING
3
3000 a 4500
4
4500 a 5000
5
5500 a 6000
6
6500 a 7000
WALL
Chock
AWNING
WALL INSTALLATION
1 Dimensions
The number of supports changes according to the awning’s width.
A
=
A
30cm
A
=
=
=
5 à 10cm
3 Adapt the awning fixation
2
to the wall type.
4
Fixation with Ø12mm screws. Screws Kit, anchors and washers are not included/provided.
5 Safe’s installation
6
8
7
N°5
CEILING INSTALLATION
1
4
A
10cm mini.
=
=
CEILING INSTALLATION : Perform the same from 1 to 8 .
Fixation with Ø12mm screws. Screws Kit, anchors
and washers are not included/provided.
REGULATION
A Arm inclination adjustment.
Ope
!
n Aw
ning
Attention, never loosen the
screws in their totality.
Relieve the arm with
one hand on the front of the awning.
1. Using a nº 19 spanner, slightly loosen the indicated
screw on both sides of the awning.
2. With an Umbrako nº 6 wrench, adjust the inclination¹.
3. Retighten the screws indicated in step 1.
1
2
¹ In a clockwise direction, the awning goes up. In the opposite direction, the
awning descends.
B Articulation adjustment.
Awning open on 50cm.
-Loosen the nut
(don’t loosen in its totality)
-Hit with a hammer on nut to bring up arm axis.
-Adjust the articulation.
-Tighten the ring after the regulation.
N°19
N°19
Alleviate the arm with hand.
Loosen
Adjust
D Plastic chocks to the fabric.
C Limit-switch adjustment
-The terminal doesn't close in a side of the
awning corners. Open the awning completely.
Utilise the maneuvering area for a motor. Insert
plastic chocks, folded in two, between the
winding tube and the fabric. The plastic chocks
should be positioned on the fabric ends. Check
closing. If the closing is not ideal, repeat the
operation, raising the number of plastic chocks.
Opening regulation screw
Closing regulation screw
-Turn the limit switch screw to + or
- to have the desired regulation.
+ To get more closing or opening,
- To get less closing or opening.
-Perform a test.
Open awning 30cm.
INFORMATION TO THE CONSUMER
Awning maintenance advice
An awning is subject to some adverse situations: humidity, sea breeze, counterweight, wind ...
We recommend that:
Check the tightening of the screws and the limit switch after installation and regularly at the beginning and end of each season.
Never close a wet awning. Dry it if possible.
Clean the fabric and the frame at the beginning and end of each season. Caution: never use detergents.
To know :
The limit switch inclination and regulation (for awnings with eléctrical maneuvers) are pré regulated during the use. They are
susceptible to be modified for use as shown in regulation.
A small flexion of the terminal could happen (4 to 5 cm). It is related with the arm main impulse and the fabric may be loose in
the central area .
A small difference of fabric fibers could be detected between two awnings when they were not acquired at the same time.
Folds or other effects may appear on the fabric. This not decrease away from the quality and effectiveness of the awning.
Ripples may appear on the fabric due to excess thickness caused by seams and hems which cause tensions on the winding
tube.
Use the emergency operation only in the event of a power failure, to close the awning. Using the emergency operation at
presence of energy will deregulate the motors’s limit switch end of the engine stroke. After using the security operation, make
sure the handle is in the spare outlet axis.
For electrical installation with an unstable switch, make sure you leave it in stop position after each use.
Problems
Solutions
Causes
The awning balcony disintegrated
from the structure.
Check proper placement of the supports (according to
the manual's instructions)
In case of fixing with a chemical seal, report to the
manufacturer.
Screws are not the most appropriate.
Check the level of the mounting brackets. Repeat
fixation with a level.
Check the level of the front bar. Rectify the adjustment
of arm inclination. (paragraph A)
The fabric is not leveled.
The front profile is not closed the
entire length.
Fabric deformation after several uses.
Bad regulation of the front profile or the arm
articulation.
Motor limit switch regulation. (paragraph C)
Articulation adjustment (paragraph B)
Proceed to plástic chocks installation. (paragraph D)
The front profile is not closed on one
side.
Fabric deformation. (Natural effect)
Electric awning maneuvers do not
work.
The engine is placed in thermal protection after 2
descents and a 1 rise successives.
Wait until the protection’s end (20 minutes).
Electric awning maneuvers do not
work.
Connection problem.
Check the motor connection.
Check engine operation by connecting directly to the
power input. (black or brown blue blue).
Don’t install in case of:
EN 13561 table ZA.1 Exterior Awning
Wind resistent
Awning width
2,5
Rain
3,5
4
4,5
5
5,5
6
6,5
7
1,5
Awning
projection
Wind
3
2
2.5
3
3,5
Snow
Nothing suspended
CLASS 2
CLASS 1
CLASS 0
EXPLODED VIEW
8
9
7
6
5
4
10
11
12
13
3
2
1
14
15
16
Number
Reference
Designation
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
DI18AR
0305A
0302EX
EB0302P
CU16P
EOI178
TO78
TAC40
0301A
EC40
TA1/9
EOI378
EI12302
BOFYYDC
PU36
EB36P
Arm regulation disc
Arm support
Winding tube support
Plastic cover 0302EX
Bushing
Ø78mm rolling tube with round shaft
Ø78mm rolling tube
Square tube 40x40
Wall supports
Plastic top TAC40
Crank 1/9
Ø78mm bushing with round shaft
Set support arm
Arm
Frontal profile
Frontal profile top
">
