Dual | XD5210 | Specifications | Dual XD5210 Specifications

XD5210
INSTALLATION/OWNERS MANUAL
AM/FM/CD Receiver
XD5210 INSTALLATION
Preparation
Please read entire manual before installation.
Before You Start
• Disconnect negative battery terminal.
(consult a qualified technician for instructions)
• Avoid installing the unit where it would be subject to high temperatures,
such as from direct sunlight, or where it would be subject to dust, dirt or
excessive vibration.
Getting Started
• Remove 2 transit screws located on top of the unit.
• Remove trim ring by pulling up gently in the center.
• Insert the supplied keys into the slots as shown, and slide the unit out of the
mounting sleeve.
• Install mounting sleeve into dash opening, bending tabs to secure.
• Connect wiring harness and antenna.
(consult a qualified technician if you are unsure)
• Certain vehicles may require an installation kit and/or wiring harness
adapter (sold separately).
• Test for correct operation and slide into mounting sleeve to secure.
• Snap trim ring into place.
2
XD5210 INSTALLATION
Installation
TYPICAL MOUNTING METHOD
3
XD5210 INSTALLATION
Wiring
Diagram
Antenna
Connector
RCA Cable
(sold separately)
GRAY Rear Preamp Output
Connect to amplifier RCA Input
BLUE Remote Turn-On
Connect to amplifier or power
antenna. Insulate wire if not used.
BLACK Ground
.5 AMP
AGC Fuse
Connect to vehicle
chassis ground.
RED Accessory
Connect to existing ignition
circuit or switched 12 volt source.
5 AMP
AGC Fuse
YELLOW Memory
Connect to battery
circuit or constant 12 volt source.
Right Front
Gray/Black (-)
Gray (+)
Left Front
White/Black (-)
White (+)
Right Rear
Violet/Black (-)
Violet (+)
Left Rear
Green/Black (-)
Green (+)
FUSES
When replacing fuses,
make sure new fuse is the
correct type and amperage.
Using an incorrect fuse
could damage the radio.
The XD5210 uses one .5
amp AGC fuse (Ignition)
and one 5 amp AGC fuse
(Battery) located in-line.
* CAUTION - Do not attach any speaker leads to ground as severe damage will occur.
4
XD5210 OPERATION
Control Locations
1
2
18
3
17
4
16
15
14
13
12
11
5
10
6
9
8
7
1 Release
10 Preset 6
2 Volume
11 Preset 5
3 Tune/Track Up
12 Preset 4/CD Random
4 Band
13 Preset 3/CD Repeat
5 Bass Boost
14 Preset2/CD Intro
6 Eject
15 Preset 1/CD Top
7 Display
16 Audio
8 Play/Pause
17 Power
9 Auto Store/Preset Scan
18 Tune/Track Down
5
XD5210 OPERATION
General Operation
Faceplate Removal
Press REL and pull away from the left side to remove.
To re-install, insert right side of faceplate first then
push left side to secure.
*For semi-permanent faceplate installation, remove trim ring and install
supplied Phillips head #1 screw through left side of mounting frame into
faceplate.
Power On/Off
CD Mode
Tuner Mode
Bass Boost
Insert a CD or press
playback.
l
/ II to begin or resume
Press PWR or BAND to begin or resume tuner
operation.
Press BASS to activate and deactivate bass boost
curve. Activating this feature will enhance the bass
frequencies when listening to music at low volumes.
Volume
Adjust volume using VOL ▲ or VOL ▼ (00-39).
Display
Press DISP to display the clock. The radio frequency
(tuner mode) or CD track/elapsed time (CD player
mode) show by default.
Set the Clock
6
Press PWR to turn the unit on. Inserting a CD will turn
the unit on automatically. Press PWR to turn the unit off.
Press DISP to display the clock, then release. Press
and hold DISP then press TUNE << to adjust the hours
and TUNE >> to adjust the minutes. Release DISP to
save the selected time.
XD5210 OPERATION
General Operation
Reset
Press and hold for more than 2 seconds to RESET the
unit upon initial installation or if abnormal operation
occurs. The RESET button is located behind the
faceplate.
Audio
Press AUD to select between Volume (default), Bass,
Treble, Balance & Fader.
Bass
Press AUD until BA appears
Press VOLUME ▼ or ▲ to adjust
(6 maximum / -6 minimum)
Treble
Press AUD until TR appears
Press VOLUME ▼ or ▲ to adjust
(6 maximum / -6 minimum)
Balance
Fader
Press AUD until B appears
Press VOLUME ▼ (LEFT) or ▲ (RIGHT) to adjust
(BL 16/BR 16) B 00 represents equal balance.
Press AUD until F appears
Press VOLUME ▲ (FRONT) or ▼ (REAR) to adjust
(FF 16/FR 16) F 00 represents equal balance.
7
XD5210 OPERATION
Tuner Operation
Seek Tuning
Manual Tuning
Band
Press TUNE << or >> momentarily to seek the next
strong station.
Press TUNE << or >> for more than 2 seconds, then
press TUNE << or >> momentarily to move radio
frequency up or down one step at a time. Press and
hold to advance quickly. If tuning is not adjusted for 2
seconds, the unit will return to seek tuning mode
(default).
Press BAND to select between FM1, FM2, FM3 and
AM1, AM2 bands.
Storing and
Recalling Station
Presets
Up to 18 FM stations and 12 AM stations can be stored.
To store a station, select the desired band and station.
Press and hold the desired preset button for more
than 2 seconds. When stored, the preset number will
appear in the display. The station can be recalled
anytime by pressing the corresponding preset button.
Automatically Store
Stations
Press AS/PS for more than 2 seconds to automatically
store the six strongest stations in the current band.
Preset Scan
8
Press AS/PS for less than 2 seconds to scan presets
1-6 on the current band, pausing for 5 seconds at
each. Press AS/PS again to cancel.
XD5210 OPERATION
CD Player Operation
Insert CD
With the label facing up, insert a standard 5" CD into
the CD slot. The CD will automatically begin playback.
Eject CD
Press the EJECT button to stop and eject the CD. The
unit will change to tuner mode.
Track Select
Press TRACK >> to skip to the beginning of the next
track. Press TRACK << to return to the beginning of
the current track. Pressing TRACK << again skips to
the beginning of the previous track.
Fast Forward
and Reverse
Pause
Intro
Repeat
Random
Top
CD-R/CD-RW
Compatibility
Press and hold TRACK << or TRACK >> to fast
forward or reverse a track.
Press
Press
ll
/ II to temporarily stop CD playback.
/ II again to resume playback.
Press INT to play the first 10 seconds of each track.
Press INT to cancel.
Press RPT to continuously repeat selected track.
Press RPT to cancel.
Press RDM to play all tracks in random order.
Press RDM again to cancel.
Press TOP to begin playback from track 1.
Some CD-Rs and CD-RWs may be incompatible with
this unit, depending on media type and recording
method.
9
XD5210 WARRANTY
Limited One-Year Warranty
This warranty gives you specific legal rights. You
may also have other rights which vary from state to
state.
Namsung America Inc. warrants this product to the
original purchaser to be free from defects in
material and workmanship, under normal
conditions, for a period of one year from the date of
the original purchase.
Namsung America agrees, at our option, during the
warranty period, to repair any defect in material or
workmanship or to furnish an equal new or renewed
product in exchange without charges, subject to
verification of the defect or malfunction and proof of
the date of purchase.
During the One-Year Warranty Period: For One Year
from the date of purchase, your product will be
replaced with a new, renewed or comparable
product (whichever is deemed necessary) if it
becomes defective or inoperative. This is done
without charge to you. Replacement products are
warranted for the balance of the original warranty
period.
Who is covered? This warranty is extended to the
original retail purchaser for products purchased and
used in the U.S.A., in the 48 contiguous states ONLY.
What is covered? This warranty covers all defects in
material and workmanship in this product. The
following are not covered: installation/removal costs,
damage resulting from accident, misuse, abuse,
neglect, product modification, improper installation,
incorrect line voltage, unauthorized repair or failure
to follow instructions supplied with the product, or
damage occurring during return shipment of the
product.
10
What to do?
1. Before you call for service, check your operating
instruction booklet. A slight adjustment of any
custom controls discussed in your instruction
booklet may save you a service call.
2. If you require service during the warranty
period, you must carefully pack the product
(preferably in the original package) and ship it by
prepaid transportation with proof of the purchase
date from the retailer to the Return Center
address listed below.
3. Please describe your problem in writing and
include your name, a return UPS shipping
address (P.O. Box not acceptable), and a daytime
phone number with your shipment.
4. DUAL will pay the return shipping charges if
the product is returned to an address within the USA.
Namsung America Inc.
Attn: Returns Center
21318 64th Ave. South
Kent, WA 98032 U.S.A.
Toll Free: 1-866-626-7863
Exclusion of Certain Damages: This warranty is
exclusive and in lieu of any and all other warranties,
expressed or implied, including without limitation
the implied warranties of merchantability and fitness
for a particular purpose and any obligation, liability,
right, claim or remedy in contract or tort, whether or
not arising from the company’s negligence, actual or
imputed. No person or representative is authorized
to assume for the company any other liability in
connection with the sale of this product. In no event
shall the company be liable for indirect, incidental or
consequential damages.
XD5210 OPERATION
Troubleshooting
Problem
Unit will not
turn on
(no power)
Cause
Action
Yellow or red wire not connected or
incorrect voltage
Check connections for proper
voltage (11~16VDC)
Black wire not connected
Check connection to ground
Fuse blown
Unit has power Speaker wires not connected
(but no sound) One or more speaker wires touching
each other or touching chassis
ground
Unit blows
fuses
Excessive
skipping
Replace fuse
Check connections at speakers
Insulate all bare speaker wires
from each other and chassis
ground
Yellow or red wire touching chassis
ground
Check for pinched wire
Speaker wires touching chassis
ground
Incorrect fuse rating
Check for pinched wire
Unit is not mounted correctly or
backstrap is not secure
Check mounting sleeve and
backstrap support
Physical defect in media
(CD, CD-R or CD-RW)
Check media for scratches
Use fuse with correct rating
Error Codes
Error Code
Cause
Action
ER01 appears on display High internal temperature
Turn unit off for 1 hour
ER02 appears on display Load/Eject operation error
Press eject or RESET
ER03 appears on display Focus adjustment error
Clean or replace media
ER04 appears on display Tracking auto adjustment error
Clean or replace media
ER06 appears on display Sled operation error
Press eject or RESET
ER07 appears on display Focus search operation error
Press eject or RESET
ER08 appears on display CLV (PLL) operation error
Press eject or RESET
ER09 appears on display TOC data read error
Clean or replace media
11
XD5210 WARRANTY
Specifications
CD Player
Signal-to-noise: >86dB
Frequency response: 20Hz-20kHz
Channel separation @ 1kHz: >65dB
D/A converter: 16 Bit
FM Tuner
Tuning range: 87.5MHz-107.9MHz
Usable sensitivity: 12dBf
50dB quieting sensitivity: 16dBf
Stereo separation @ 1kHz: 40dB
Frequency response: 30Hz-13kHz
AM Tuner
Tuning range: 530kHz-1710kHz
Usable sensitivity: 30uV
Frequency response: 80Hz-2kHz
General
Total power output: 120 Watts Peak
Power output: 30Wx4 @ 4 ohm, 14.4 VDC
Operating voltage: 11-16 VDC, negative ground
Speaker output impedance: 4~8 ohms
Fuses: .5 amp fast blow AGC, 5 amp fast blow AGC
Dimensions: 7" x 7" x 2" (178 x 178 x 51 mm)
Design and specifications subject to change without notice
Namsung America Inc.
21318 64th Ave. South
Kent, WA 98032
Toll Free: 1-866-626-7863
www.dualav.com
©2004 Namsung America, Inc.
EVOK0204-V01
DCS65
INSTALLATION/OWNERS MANUAL
Multi-fit 6.5" 2-way Car Audio Speakers
DCS65 INSTALLATION
Preparation/Installation
Please read entire manual before installation.
Before You Start
• Disconnect negative battery terminal.
(consult a qualified technician for instructions)
Getting Started
• Be sure to carefully read and understand the instructions before attempting to install
the product.
• For easier assembly, we recommend that if additional wiring is required, that you run
all wires prior to mounting your speaker in place.
• Use the highest quality connectors for a reliable installation and to minimize signal or
power loss.
• Use caution before you drill or cut! Be careful not to cut or drill into gas tanks, fuel lines,
brake or hydraulic lines, vacuum lines or electrical wiring when working on any vehicle.
• Never run speaker wires underneath your vehicle. Running speaker wires inside the
vehicle provides the best protection from exhaust heat and environmental elements.
• Avoid running wires over, near, or through sharp edged surfaces. We suggest you also
use rubber grommets to protect any wires routed through metal, especially the firewall.
Mounting
1.Determine where the speakers will be mounted. Ensure an area large enough for the
speaker to mount evenly. Be sure that the mounting location is deep enough for the
speaker to fit. Using an appropriate tool, cut a 4.9" diameter mounting hole.
2.If supplied, use the plastic mounting ring as a template to mark the locations for the
mounting screws. Drill the holes with a 3/32" bit.
3.Be sure to observe proper polarity when connecting the wires. The speaker's positive
terminal is indicated with a "+".
4.Fit the ring and speaker to the cutout. Mount them using the enclosed screws. If supplied,
fit the grille inside the ring and press gently, but firmly, into place.
TYPICAL MOUNTING METHOD
grille
mounting ring
speaker
mounting hole
cut-out
2
DCS65 WARRANTY
Limited One-Year Warranty
This warranty gives you specific legal rights. You may
also have other rights which vary from state to state.
Namsung America Inc. warrants this product to the
original purchaser to be free from defects in material
and workmanship, under normal conditions, for a
period of one year from the date of the original purchase.
Namsung America agrees, at our option, during the
warranty period, to repair any defect in material or
workmanship or to furnish an equal new or renewed
product in exchange without charges, subject to
verification of the defect or malfunction and proof of
the date of purchase.
During the One-Year Warranty Period: For One Year
from the date of purchase, your product will be
replaced with a new, renewed or comparable product
(whichever is deemed necessary) if it becomes
defective or inoperative. This is done without charge
to you. Replacement products are warranted for the
balance of the original warranty period.
Who is covered? This warranty is extended to the
original retail purchaser for products purchased and
used in the U.S.A., in the 48 contiguous states ONLY.
What is covered? This warranty covers all defects in
material and workmanship in this product. The
following are not covered: installation/removal costs,
damage resulting from accident, misuse, abuse,
neglect, product modification, improper installation,
incorrect line voltage, unauthorized repair or failure to
follow instructions supplied with the product, or
damage occurring during return shipment of the
product.
What to do? 1. Before you call for service, check your
operating instruction booklet. A slight adjustment of
any custom controls discussed in your instruction
booklet may save you a service call.
2. If you require service during the warranty period,
you must carefully pack the product (preferably in the
original package) and ship it by prepaid transportation
with proof of the purchase date from the retailer to
the Return Center address listed below.
3. Please describe your problem in writing and
include your name, a return UPS shipping address
(P.O. Box not acceptable), and a daytime phone
number with your shipment.
4. DUAL will pay the return shipping charges if the
product is returned to an address within the USA.
Namsung America Inc.
Attn: Returns Center
21318 64th Ave. South
Kent, WA 98032 U.S.A.
Toll Free: 1-866-626-7863
Exclusion of Certain Damages: This warranty is exclusive
and in lieu of any and all other warranties, expressed
or implied, including without limitation the implied
warranties of merchantability and fitness for a particular
purpose and any obligation, liability, right, claim or
remedy in contract or tort, whether or not arising
from the companyís negligence, actual or imputed.
No person or representative is authorized to assume
for the company any other liability in connection with
the sale of this product. In no event shall the company
be liable for indirect, incidental or consequential
damages.
3
DCS65 SPECIFICATIONS
Specifications
Outside Diameter
6.75"
Mounting Depth
1.7"
Mounting Height
.3"
Cut-out Diameter
4.9"
Frequency Response
Sensitivity
88Hz-15kHz, ±3dB
89dB 1W/1M
Impedance
4 ohms
RMS Power
25 Watts
Peak Power
65 Watts
Design and specifications subject to change without notice
Namsung America Inc.
21318 64th Ave. South
Kent, WA 98032
Toll Free: 1-866-626-7863
www.dualav.com
©2004 Namsung America, Inc.
EVOK0604-V01
Download PDF