YEAR
2
WARRANTY
Multi Processor
RHMP750
INSTRUCTIONS & WARRANTY
RHMP750_IB_RB2_041111
Spectrum Brands Australia Pty Ltd
Locked Bag 3004 Braeside
Victoria 3195 Australia
Spectrum Brands New Zealand Ltd
PO Box 9817 Newmarket
Auckland 1149 New Zealand
Customer Service in Australia
TollFree: 1800 623 118
Email: info@spectrumbrands.com.au
Website: www.spectrumbrands.com.au
Customer Service in New Zealand
TollFree: 0800 736 776
Email: service@spectrumbrands.co.nz
Website: www.spectrumbrands.co.nz
Spectrum Brands Australia Pty Ltd and Spectrum Brands New Zealand Ltd
Warranty Against Defects
W
0911
In this warranty:
Australian Consumer Law means the Australian consumer law set out in Schedule 2 to the
Competition and Consumer Act 2010;
CGA means the New Zealand Consumer Guarantees Act 1993;
Goods means the product or equipment which was accompanied by this warranty and
purchased in Australia or New Zealand, as the case may be;
Manufacturer, We or us means:
1. for Goods purchased in Australia, Spectrum Brands Australia Pty Ltd ABN, 78 007 070 573;
or
2. for Goods purchased in New Zealand, Spectrum Brands New Zealand Ltd, as the case
may be, contact details as set out at the end of this warranty;
Supplier means the authorised distributor or retailer of the Goods that sold you the Goods in
Australia or in New Zealand; and
You means you, the original end-user purchaser of the Goods.
1. Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law, or the CGA. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
2. The benefits provided by this Warranty are in addition to all other rights and remedies in
respect of the Goods which the consumer has under either the Australian Consumer Law
or the CGA. The original purchaser of the Goods is provided with the following Warranty
subject to the Warranty Conditions:
3. We warrant the Goods for all parts defective in workmanship or materials from the date
of purchase (Warranty Period), for the period of:(a) Two (2) years for Russell Hobbs products (see product packaging for details)
(b) Two (2) years with five (5) year motor warranty for Russell Hobbs products (see product
packaging for details)
(c) Limited Lifetime, Ten (10) years for Russell Hobbs cookware.
(d) One (1) year for George Foreman, iRobot, Westinghouse, Black & Decker and Spectrum
Brands products.
If the Goods prove defective within the Warranty Period by reason of improper workmanship
or material, we may, at our own discretion, repair or replace the Goods without charge.
Warranty Conditions
4. The Goods must be used in accordance with the manufacturer’s instructions. This
Warranty does not apply should the defect in or failure of the Goods be attributable
to misuse, abuse, accident or non-observance of manufacturer’s instructions on the
part of the user. As far as the law permits, the manufacturer does not accept liability
for any direct or consequential loss, damage or other expense caused by or arising
out of any failure to use the Goods in accordance with the manufacturer’s instructions.
5. Exhaustible components (such as batteries, filters and brushes) of the Goods are
included under this Warranty only where there is a defect in workmanship or materials
used.
6. The warranty granted under clause 3 is limited to repair or replacement only.
7. Any parts of the Goods replaced during repairs or any product replaced remain the
property of the manufacturer. In the event of the Goods being replaced during the
Warranty Period, the warranty on the replacement Goods will expire on the same
date as for the Warranty Period on the original Goods which are replaced.
8. In order to claim under the warranty granted under clause 3 you must:
(a) Retain this warranty with your receipt/proof of purchase; and
(b) Return the Goods to us at the relevant address or to the Supplier by prepaid
freight within the Warranty Period accompanied with (i) the legible and unmodified
original proof of purchase, which clearly indicates the name and address of the
Supplier, the date and place of purchase, the product name or other product serial
number and (ii) this warranty.
9. This warranty is immediately void if:
(a) Any serial number or appliance plate is removed or defaced;
(b) The Goods have been serviced or otherwise repaired by a person not authorised
to do so by us or where non approved replaced parts are used.
10. The Goods are designed for domestic use only. A limited 90-day Warranty applies to
any industrial or commercial use of the Goods. The Goods must be connected to the
electrical voltage requirements as specified in the ratings label located on the Goods.
11. This warranty does not cover the cost of claiming under the warranty or transport
of the Goods to and from the Supplier or us.
12. This warranty is only valid and enforceable in Australia against Spectrum Brands
Australia Pty Ltd and in New Zealand against Spectrum Brands New Zealand Ltd.
Contact us or the Supplier for further details.
Register your product online
If you live in Australia please visit: www.spectrumbrands.com.au/warranty
If you live in New Zealand Please visit: www.spectrumbrands.co.nz/warranty
Registration of your warranty is not compulsory, it gives us a record of your purchase
AND entitles you to receive these benefits: Product information; Hints and tips; Recipes
and news; Information on special price offers and promotions.
Any questions? Please contact Customer Service for advice.
Congratulations on the purchase of your new Russell Hobbs appliance. Each unit is manufactured
to ensure safety and reliability. Before using the Multi Processor for the first time, please read this
instruction booklet carefully and keep it for future reference. Pass it on if you pass on the Multi
Processor.
When using this appliance, basic safety precautions should always be followed.
1
2
3
15
16
4
5
17
8
6
9
17A
6A
7
10
14
NOTE: Product may vary
slightly from what is illustrated.
13
12
11
1. Food pusher
7. Base
14. Controls
2. Wide-mouth feed chute
8. Storage lid
15. 500ml workbowl cover
3. 2 Litre processing
9. Dough blade
16. Small stainless steel
workbowl cover
4. Coarse slice/grate disc
10. Large stainless steel
chopping blade (White)
5. Disc stem
11. Fine slice/grate disc
6. 2 Litre processing
12. Cord wrap (under base)
workbowl
6A. Centre Post (White)
13. Non-slip suction feet
chopping blade (Black)
17. 500ml processing
workbowl
17A. Centre Post (Black)
18
19
20
21
22
23
24
18. Lid cap with measurement units
22. Gasket
19. Lid
23. Blade assembly
20. 1.25 Litre glass blender jug
24. Jug base
21. Handle
Important: Please Read the below two points before using you Multi Processor.
TAMPER-RESISTANT SCREW
Warning: This appliance is equipped with a tamper-resistant screw to prevent removal of the
outer cover. To reduce the risk of fire or electric shock, do not attempt to remove the outer cover.
There are no user-serviceable parts inside. Repair should be done only by qualified service
personnel.
ELECTRICAL CORD
The cord of this appliance was selected to reduce the possibility of tangling in or tripping over
a longer cord. If more length is needed, use an extension cord rated no less than 10 amperes.
When using an extension cord, do not let it drape over the working area or dangle where
someone could accidentally trip over it. Handle cord carefully for longer life; avoid jerking or
straining it at outlet and appliance connections. The maximum rating is based on the chopping
blade; other attachments may draw significantly less power.
Before first use
CAUTION: Handle chopping blades and slice/grate disc carefully.
•
Remove all packaging material and any stickers from the product. Wash all removable parts
as instructed in “care and cleaning” section of this manual.
•
Select a level, dry countertop where the appliance is to be used, allowing air space on all
sides to provide proper ventilation for the motor (50mm gap min).
Assembly of the processor bowls
How to insert and remove the centre post
•
The centre post of the bowl is removable (2L processor bowl - White, 500ml mini processor
bowl - Black):
•
Turn the bowl upside down.
•
Grasp the outer tabs and turn the centre post clockwise until the locking tabs are free. Lift
the post out (A).
•
To return to its original position, place centre post into opening in bottom of workbowl and
turn counter-clockwise until tabs snap into place.
NOTE: The 2L bowl and 500ml bowl centre posts are not interchangeable.
How to lock the workbowl in position:
•
Place the workbowl on the base with handle turned to the right of the locking mechanism
(B) over the unlock symbol .
•
Hold handle and rotate workbowl clockwise toward the lock symbol until it clicks firmly
into place (C). Be sure to lock the workbowl in place before attaching the blades and cover.
How to Lock the Cover
•
Place cover over workbowl with the small latch to the right of the workbowl’s handle (D).
•
Hold workbowl cover and rotate clockwise until cover locks into place.
Important: For your protection this appliance has an interlock system. The processor will
not operate unless the workbowl, cover and wide-mouth feed chute are properly locked in
place.
•
Place the wide-mouth feed chute on top of the cover with the small tab to the right of the
workbowl’s handle. Turn clockwise until it clicks into position in the handle.
•
Insert the food pusher into the central tube of the wide mouth feed chute. Turn clockwise to
lock in place. The pusher is used to guide foods through the feed chute and can be
removed when adding liquid or additional foods while the processor is running.
•
To remove, turn anticlockwise.
A
A
B
B
C
C
D
Controls
•
The controls are located on the front of the base (E).
•
Press PULSE, HIGH or LOW to select a function (see directions below).
OFF/PULSE
•
Processor should be stored in OFF position and unplugged when not in use.
•B Use PULSE for short processing
tasks. This lets
C
Dyou control the size and uniformity of foods
being chopped.
•
The OFF/PULSE button must be pressed and held for the appliance to operate in PULSE
mode. When released, the appliance will stop.
•
The motor of the processor will run as long as the OFF/PULSE button is held down.
•
Press the button and then release to allow the blades to stop running and the food to fall to
the bottom of the workbowl.
•
Pulsing gives better control when chopping, mincing, mixing and blending foods. You can
foods, from coarse to fine.
C control the size of the D
HIGH and LOW
•
D
E
When either speed is selected, the processor will run continuously until the OFF/PULSE
button is pressed.
How to chop in the workbowl
The chopping blade is used to coarsely or finely chop, mince, mix and puree foods to a smooth
consistency.
•
Lock workbowl into position (see Illustrations B and C).
•
Hold chopping blade by centre shaft and insert onto centre post (F).
F
CAUTION: The blade attachments are very sharp. Use caution when handling and storing.
•
Place food in workbowl.
•
Place cover on workbowl and lock into place by rotating clockwise (see Illustration D).
•
Place the wide-mouth feed chute and food pusher in place, turn to lock.
CAUTION: Never use your fingers to direct food through the chute.
•
Select your desired speed (PULSE, LOW or HIGH).
NOTE: Process foods for no more than a few seconds at a time. Pulsing produces excellent
results and offers greater control.
•
Food can be added while processor is running; remove food pusher and insert food through
the feed chute. Replace food pusher in chute.
CAUTION: Be sure chopping blade has completely stopped spinning before removing cover
from processor.
•
Press the OFF/PULSE button and allow blades to stop revolving before removing cover.
Twist cover toward to remove.
•
Unlock workbowl by turning it anti-clockwise and lift off base.
NOTE: Remove bowl from appliance before removing blade to prevent food from leaking through
the centre opening of the bowl.
•
Carefully remove chopping blade.
•
Unplug appliance when not in use.
Helpful Tips for Chopping and Blending
•
The processor works very quickly. Watch carefully to avoid over-processing foods.
•
The PULSE button offers the best control and results. Process using PULSE in 5 second
intervals.
•
For best results, process foods that are about the same size.
•
The large workbowl has a capacity of 2L, and the small workbowl has a capacity of 500ml.
•
Do not overload the bowl.
•
Do not process more than 3 cups of liquid in the large workbowl at one time.
•
Insert a funnel into the feed chute when adding ingredients such as, oil, flour and sugar.
•
Do not process boiling liquids.
•
To process meat, use no more than 2 cups of 20mm cubes in the large workbowl.
How to use the dough blade (same assembly method as the chopping blade)
This blade makes preparing dough efficient and time-saving.
NOTE: This blade does not extend to the outside rim of the workbowl, so it cannot incorporate
flour when very small amounts of flour are being processed.
•
Push dough blade down as far as it will go into workbowl.
•
Insert all the dry ingredients into the workbowl.
•
Place cover on workbowl. Add wide-mouth feed chute and food pusher. Process to blend.
•
Add liquids through the small feed chute with machine running.
Helpful Tips when using the Dough Blade
•
For best results do not prepare recipes using more than 3½ cups flour.
•
Begin with 1 cup less than the maximum amount of flour and add additional flour once
mixture is well blended.
•
Pour liquid through food chute gradually.
•
Knead dough no longer than 1 minute.
How to slice or grate
•
Lock workbowl into position (see Illustrations B and C).
•
Place disc stem onto centre post in workbowl.
•
Carefully place slice/grate disc on stem with appropriate side up (depending on work to be
done).
CAUTION: The blade attachments are very sharp. Use caution when handling and storing.
•
Place cover on workbowl and lock into place by rotating cover clockwise (see Illustration
D).
•
For large size food insert before attaching the chute, then attach chute and use the pusher
Fig G(a). For smaller size food, attach cover and feed through using pusher.
NOTE that the pusher clips onto the moving chute tube. Fig G.
OR
G
•
G(a)
Select PULSE, LOW or HIGH; press firmly on food pusher to guide food through processor,
but do not force it.
NOTE: Heavy pressure on the pusher does not speed the work; use the pusher only as a guide.
Let the processor do the work.
•
When finished, press OFF/PULSE and wait for disc to stop rotating before removing cover.
Twist cover toward to remove.
•
Carefully remove slice/grate disc. Unlock workbowl by turning it counter-clockwise and
lifting it off the base.
•
Unplug appliance when not in use.
Helpful Tips When Slicing and Grating
•
Before slicing round fruits and vegetables in the processor, cut a thin slice from the bottom
so food will be more stable. Place food cut side down in feed chute.
•
Always remove seeds and pits before processing.
•
Remove the core from hard vegetables, such as cabbage.
•
When slicing thinner vegetables, cut them just short of the length of the feed chute and
stand them vertically in feed chute so they are solidly packed and cannot turn or tilt.
•
Grate hard cheeses at room temperature.
•
Soft and semi-hard cheeses should be well chilled before grating.
•
After food has been processed, remove the cover and invert on countertop. Remove the
slice/grate disc before removing the workbowl from the processor. Place the disc on top of
the inverted workbowl cover.
General Tips for using the Food Processor
•
Organize processing tasks to avoid multiple cleanups of the bowl; process dry before wet.
•
The processor will be more efficient if filled no more than 2/3 full.
•
To take advantage of the speed of the processor, drop foods through the food chute with
the processor running.
•
Apply light pressure on the pusher for soft foods (berries and tomatoes) and slightly more
pressure for hard foods (onions and potatoes).
•
Do not process foods that are so frozen or so hard that the tip of a knife cannot be inserted
into the food.
•
When chopping dried fruits add a little flour to keep the pieces from sticking together.
•
Chill soft cheeses before slicing and grating to prevent the cheese from rolling into a ball on
the disc.
•
When using the slicing / grating disc do not let the food accumulate too high; stop and
empty the workbowl.
•
Although plastic parts of the processor are dishwasher safe, wash them by hand to retain
their clear appearance.
•
To easily clean the workbowl, once empty add a drop of detergent and a little hot water and
pulse several times. Rinse before reusing.
•
Do not use the processor to:
- Grind bones, grains or hard spices
- Liquefy fruits and vegetables
- Slice warm meat and hard cooked eggs; chill them first.
Assembly of the Blender Jug
•
Turn blender jug upside down and place flat on counter top or work surface.
•
Put the gasket on top of the blade assembly. Place the blade assembly with gasket in
bottom opening of the jug with blades down.
•
Place jug base onto jug and rotate clockwise until it is tight (H).
•
Turn assembled jug right side up.
•
Place lid with lid cap in place on blender jug.
•
Place jug on power base with tab on base slightly to the right of the locking mechanism and
rotate clockwise until blender locks into place (J).
•
The blender is now ready for use.
H
J
How to use the Blender
•
Make sure appliance is OFF.
•
Place foods to be blended into jug.
•
Place lid on jug; make sure lid cap is in place.
•
Plug power cord into standard electrical outlet.
NOTE: When in use do not leave blender unattended. When using hard foods, such as ice, nuts
and coffee beans, keep one hand on the lid to keep blender in place.
•
Select the speed that best suits your desired task.
NOTE: Use the PULSE button to begin the blending process when preparing beverages that
include ice cubes; this helps to produce a smoother texture. Use the PULSE button for several
seconds; then release. Releasing the PULSE button automatically turns the blender off.
•
Open the lid cap to add ingredients while the blender is running, and drop ingredients
through the opening (K).
NOTE: Do not remove the lid while the blender is running.
•
When finished, press the OFF/PULSE button.
•
To remove the jug, using thumb and forefinger, push tab on blender base to the right to
release the locking mechanism (L).
•
Grasp the handle of the blender jug and lift up.
•
Remove the lid to pour.
•
Always unplug the appliance when not in use.
K
L
Helpful tips when blending
•
Cut food into pieces no larger than 20mm for use in the blender.
•
When ingredients splatter onto the sides of the jug or the mixture is very thick, press the
OFF/PULSE button to turn appliance off. Remove the lid and use a rubber spatula to scrape
down the sides of the jug and to redistribute the food pushing food toward the blades.
Replace the lid and continue blending.
•
Blender should always have lid with lid cap in place when in use.
•
Do not place blender jug on base when motor is running.
•
The lid cap holds ¼ cup liquid and can be used when adding ingredients such as juices,
milk, cream and liquor (M).
•
When making bread crumbs, chopping nuts or grinding coffee beans make sure blender jug
is completely dry.
•
When using a PULSE function use short bursts. Allow the blades to stop rotating between
pulses.
•
Use the PULSE button when preparing beverages that include ice cubes; this helps to
produce a smoother texture.
•
It is helpful to begin the blending process on the lowest speed and then increase to a higher
speed, if necessary.
•
When blending hot ingredients always open the lid cap and replace it ajar with the opened
side away from you. Cover lid with a cloth to avoid splattering and only use low speed. Do
not blend more than 3 to 3½ cups at a time (N).
•
DO NOT place any of the following in the blender:
- Large pieces of frozen foods
- Tough foods such as raw turnips, sweet potatoes and potatoes
- Bones
- Hard salami, pepperoni
- Boiling liquids (cool for 5 minutes before placing in blender jug.)
•
Tasks not recommended for the blender:
- Whipping cream
- Beating egg whites
- Mixing dough
- Mashing potatoes
- Grinding meats
- Extracting juice from fruits and vegetables
M
N
Care and Cleaning
NOTE: Before cleaning, be sure unit is turned off and cord is unplugged.
•
Completely disassemble processor parts before washing.
•
Whenever possible, rinse parts immediately after processing for easy cleanup.
•
Wipe base and feet with a damp cloth and dry thoroughly. Stubborn spots can be removed
by rubbing with a damp cloth and a mild, nonabrasive cleaner. Do not immerse base in
liquid.
•
All removable parts can be washed by hand or in a dishwasher. Hand washing of plastic
parts will help to maintain the processor’s appearance.
•
If washing by hand, fill workbowl with hot soapy water and rapidly raise and lower the
cutting blade and discs up and down on the centre shaft.
•
If your sink has a sprayer nozzle, you will find it helpful in rinsing the blades.
•
If washing in a dishwasher, place removable parts on top rack only – not in or near utensil
basket.
•
Some staining of parts may occur. Make a paste of 2 tablespoons baking soda / 1
tablespoon water. Apply to stains and let stand overnight. Rinse and dry.
•
Do not use rough scouring pads or cleansers on any plastic or metal parts.
•
Do not allow blades or discs to soak in water for long periods of time.
•
Remove the workbowl cover and blade. Invert an empty 35mm film canister over the hole in
the workbowl. Fill with hot, soapy water and allow to soak.
•
Remember to clean the internal shaft of the chopping blade; use a baby bottle brush to
remove any clogged food particles.
•
If you are having trouble closing the cover over the workbowl, apply a small amount of
vegetable oil to the rim of the cover and workbowl. This should make the pieces work
smoother when attaching the cover to the bowl.
NOTE: Do not attempt to sharpen the cutting edges of the blades or disc. They are permanently
sharpened at the factory and will be ruined by attempted sharpening.
Speed Setting Use
LOW
•
Reconstituting frozen juices and drink mixes
•
Preparing salad dressings
•
Pureeing hot soups
•
Blending pancake and waffle batter or mixes
•
Beating eggs for omelettes and custards
•
Making cookie crumbs and bread crumbs
•
Preparing sauces and salsa
HIGH
•
Coarse to fine chopping of nuts, vegetables and fruits
•
Grinding hard cheeses, spices and coffee beans
•
Baby foods – fruits and vegetables
•
Milk shakes
PULSE
•
Ice crushing
•
Chopping vegetables
•
Thick beverages
•
Smoothies
TROUBLESHOOTING
FOOD PROCESSOR
PROBLEM
POSSIBLE CAUSE
SOLUTION
Food is unevenly
chopped.
Workbowl is overfilled.
Smaller amounts will process more
evenly.
You may be running the bowl
continuously instead of using
PULSE.
Food may be cut in random
sizes.
Use the PULSE button in 5 second
increments or less. Allow the blades to
stop completely before pressing the
PULSE button again.
Cut food in same size pieces before
placing in processor.
Liquid leaks from the
bottom of the
workbowl.
Too much liquid in the
workbowl.
Process smaller amounts.
When processing liquids, do not add
more than 3 cups to workbowl.
Do not remove the blade before
removing workbowl from processor
when processing liquids.
Sliced foods are
uneven and slanted.
Foods being sliced or
grated fill up on one
side of the bowl.
The feed chute has not been
well packed or uneven
pressure has been applied to
the food pusher during
processing.
Cut pieces in even lengths, just a little
shorter than the length of the feed
chute.
This is normal.
Stop processing occasionally and either,
even out the food in the workbowl or
move it to another bowl.
Pack the chute carefully and\maintain
even pressure on the food pusher as the
food is being processed.
When food accumulates close to the
disc, empty the workbowl before
continuing.
Some pieces of food
remain on top of the
slice/grate disc.
This is normal.
Slice or grate those pieces by hand or
save for another use, like soups that will
be pureed.
Soft cheese collects
on top of the slice/
grate disc.
The cheese was not cold
enough. The pressure exerted
on the pusher was too great.
Be sure soft cheeses are well chilled or
place in freezer until knife inserted into
cheese penetrates about 12mm.
Remember food pusher is to be used as
a guide; never exert hard pressure on
the food pusher.
BLENDER
PROBLEM
POSSIBLE CAUSE
SOLUTION
Jug bottom does not
come off the jug.
A vacuum has been formed.
Place the jug on the blender, hold the
base steady and turn counter clockwise
until jug is released from the bottom.
Liquid is leaking from
bottom of jug.
Gasket is either missing or not
in place correctly.
Check that jug is assembled correctly.
Appliance does not
turn on.
Appliance is not plugged in
jug is not in place.
Check that appliance is plugged into a
working outlet. Blender jug must be
securely in place.
Mixture in blender
does not seem to be
blending.
Not enough liquid in mixture
being blended or too much
ice.
Turn the blender off and use a rubber
spatula to redistribute the food; add
some liquid and pulse the mixture to aid
in the blending process.
SAFEGUARDS
When using this appliance, basic safety precautions should always be followed, including but not
limited to the following:
IMPORTANT SAFEGUARDS
1. To protect against electric shock do not immerse cord, plug or body of unit in water or liquid.
2. Do not use outdoors or in damp or moist areas.
3. This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
4. This appliance is not a toy. Young children should be supervised to ensure they do NOT play with
the appliance.
5. Always turn off and unplug from the power outlet when not in use, before putting on or taking
off parts, and before cleaning the appliance.
6. Do not operate any appliance with a damaged cord or plug or after the appliance has
malfunctioned, or has been dropped or damaged in any manner. Contact customer service for
replacement, examination, repair or adjustment.
7. There are no user serviceable parts. If the power cord is damaged, it must be replaced by the
manufacturer or a suitably qualified person in order to avoid a hazard.
8. The use of accessory attachments not recommended by the appliance manufacturer may cause
injuries.
9. Do not use on an inclined plane or unstable surface.
10.Keep the processor and power cord away from the edge of benches and counter tops.
11. Do not place on or near any heat surfaces.
12.To disconnect, press OFF. Turn off the wall power outlet, then grasp the plug and remove from
wall outlet. Never pull by the cord.
13.Do not use appliance for other than its intended purpose.
14.The motor will only operate once the processing bowl and lid have been securely fitted onto the
motor unit.
15.Keep hands and utensils away from moving blades or discs while processing foods to prevent
the possibility of severe personal injury or damage to the food processor. A scraper may be
used, but it must be used only when the food processor is not running.
16.Cutting blades are very sharp. Care must be taken when handling the sharp cutting blades,
when emptying the bowl and during cleaning.
17. To reduce the risk of injury, never place cutting blade or disc on base without first fitting the
bowl securely in place.
18.Be certain cover is securely locked in place before operating appliance.
19.Never feed food into cute by hand. Always use the food pusher.
20.Do not attempt to defeat the cover interlock mechanism.
21.Press OFF to cancel any function.
22.Do not operate from a timer or other remote control system
23.For added safety, electrical appliances should be connected to a power outlet that is protected
by a residual current device (RCD), also often referred to as a ‘Safety Switch’. Your switchboard
may already incorporate an RCD. If unsure, call an electrician for verification and fitting if
necessary.
SAVE THESE INSTRUCTIONS
THIS APPLIANCE IS FOR HOUSEHOLD USE ONLY
Recipes
Multi Processor
RHMP750
Tapenade
Makes approx. 2 cups
INGREDIENTS
100g pitted olives
6 bottled anchovies
100g tuna, flaked
1 tbsp Dijon mustard
1 tbsp capers
1. Place olives into the Blender jug and at low
speed, chop coarsely. Chop anchovies and
add to the olives with tuna, capers and approx
⅓ of the olive oil.
2. Process until just blended, scraping down the
sides of the bowl if necessary. Gradually add
the rest of the oil and process until smooth.
200ml virgin olive oil
Coriander Pesto
Makes approx. 2 cups
INGREDIENTS
4 handfuls fresh coriander
250ml olive oil
4 cloves fresh garlic
80g pine nuts
120g grated parmesan
cheese
1. Put the coriander, garlic and pine nuts into the
Blender jug. Add a tablespoon of oil, and pulse
until combined. Repeat until all the oil has
been blended through.
2. Mix in the Parmesan cheese and season with
salt and pepper.
3. Serve tossed through warm pasta, or as a dip.
Salt & pepper, to taste
RUSSELL HOBBS and logo are Trade Marks of Spectrum Brands, Inc., or one of its subsidiaries.
©2011 Spectrum Brands, Inc.
Recipes are to be used in conjunction with the Multi Processor by Russell Hobbs. All rights reserved. No part of this publication may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or
otherwise, without prior permission of the copyright owner.
Photography: Salton Australia - Designed in Australia.
Savoury Cheese Balls
Makes 20
INGREDIENTS
250g soft cream cheese
½ cup parmesan cheese grated
2 tbsp spring onion, chopped
1 tbsp Worcestershire sauce
1 tbsp lemon juice
1 tbsp mixed herbs
½ tsp chilli flakes
Pepper, to taste
1 tbsp sour cream
Chopped mixed nuts, toasted
1. Scoop cheese into the Blender jug.
Add parmesan cheese, spring onion,
Worcestershire sauce, lemon juice, herbs,
chilli and pepper to the Blender jug.
2. Blend lightly at low speed and add sour cream
to lighten mixture. Blend at low speed until
smooth.
3. Scoop into a bowl and chill until firm enough to
handle easily.
4. Roll into walnut sized balls and then roll each
in chopped nuts.
5. Serve on a platter with crackers, grapes and
dried fruits.
Creamed Broccoli Soup
Serves 4
INGREDIENTS
2½ cups chicken or vegetable
stock
2 medium potatoes, peeled
and diced
200g broccoli, cut into small
pieces
½ cup cream
Salt & pepper to taste
1. Place broccoli, stock and potatoes into a
saucepan, cover with stock and cook on
medium heat until vegetables are tender.
2. Transfer vegetables and liquid into the Food
Processor, reserving a few small sprigs of
broccoli for garnish.
3. At low speed, blend until coarsely chopped
then increase speed and blend until smooth.
4. Return the soup to the saucepan, stir in the
cream and add salt and pepper to taste.
Reheat gently, stirring occasionally, without
allowing to boil.
5. To serve, ladle into bowls, swirl a little cream
into each and garnish with the small sprigs of
reserved broccoli.
3
Coleslaw
Makes about 6 cups
INGREDIENTS
1. Using thin slicing blade, thinly slice cabbages.
½ medium head cabbage,
cut into wedges
2. Using the grating disc, grate the carrots and
onion.
1 wedge purple cabbage
2 medium carrots, peeled
and trimmed
1 small purple onion
3. Place vegetables in a large bowl and add the
olives.
4. In a smaller bowl, blend remaining ingredients.
½ cup stuffed olives,
coarsely chopped
5. Pour over cabbage mixture and toss to
combine.
¾ cup mayonnaise
6. Cover and refrigerate at least 1 hour to allow
flavours to blend.
3 tbsp red wine vinegar
½ tsp celery seed
Ground pepper, to taste
Pizza Dough
Makes 1 base, approx 35cm diameter
INGREDIENTS
1¼ tsp active dry yeast
1⅓ cups warm water (40°C)
¼ tsp sugar
3½ to 3¾ cups unsifted
plain flour
1 tsp salt
2 tbsp olive oil
1. Sprinkle yeast over water, add sugar and let
stand for 5 minutes until yeast is dissolved.
2. Position dough blade in workbowl of Food
Processor.
3. Add 3 cups flour, salt and olive oil. With
processor running, gradually add yeast mixture
down food chute. Add additional flour to make
soft dough. Continue processing dough for 1
minute.
4. Transfer dough to lightly floured board. Shape
into ball and cover with towel or large bowl. Let
dough rest for 10 minutes.
5. On lightly floured board, knead several times
until smooth and elastic; form into ball. Place
in greased bowl, turning to grease the top.
Cover and let rise at room temperature until
doubled in bulk. (About 1 hour)
6. Punch dough down, and roll out to a circle
approximately 35cm diameter.
4
Stuffed Mushrooms
Serves 6
INGREDIENTS
1. Preheat the oven to 175° C.
200g sausage meat
2. In a frypan, cook the sausage meat over a
medium heat, stirring to break into bits.
12 large mushrooms
1 large spring onion
1 large clove garlic
1 slice white bread
2 tbsp parsley, chopped
2 tbsp vegetable stock
4 tbsp melted butter
½ cup parmesan cheese,
grated
3. Remove the stem from the mushrooms, being
careful not to break mushroom caps. Set
mushroom caps aside.
4. In the Food Processor bowl, place the spring
onion and garlic, and process on low to chop.
Add white bread and mushrooms stems and
process for a few seconds to break into small
pieces.
5. Add cooked sausage and process for several
seconds. Stir in parsley and stock.
6. Melt the butter in a large bowl, and toss
mushroom caps until coated. Arrange in
single layer in shallow baking dish. Fill with
the sausage mixture. Top with the parmesan
cheese.
7. Bake for 15 minutes until hot and bubbly.
8. Serve with a dollop of sour cream.
5
Spinach Pesto Pizza
Makes one 35cm pizza.
INGREDIENTS
1. Preheat the oven to 230°C.
1 pizza base
2. Fit the large processor bowl with the chopping
blade. Place all ingredients for the pesto in the
bowl and process until smooth.
440g mozzarella cheese
4 tomatoes, sliced
70g parmesan cheese
¼ cup loosely packed basil
leaves
3. Grate mozzarella cheese using coarse grating
disc and set aside. Repeat process to grate
parmesan cheese.
Salt & pepper, to taste
4. Place the pizza base onto a lightly greased
pizza pan.
SPINACH PESTO
5. Spread pesto evenly on pizza base leaving
about 1.5cm border. Sprinkle mozzarella
cheese evenly over pesto. Arrange tomato
slices over cheese.
2 cups spinach leaves
1 cup basil leaves
½ cup parsley
110g parmesan cheese
½ cup pine nuts
2 cloves garlic, minced
6. Sprinkle with Parmesan cheese and basil.
Season to taste.
7. Bake in the oven for about 12 minutes, or until
crust is browned and cheese is golden.
1 tsp grated lemon peel
¾ cup olive oil
6
French Crepes
Serves 4
INGREDIENTS
1 cup plain flour, sifted
2 tsp castor sugar
2 eggs
½ cup milk
½ cup water
2 tbsp butter, melted
Fresh strawberries
Castor sugar to taste
1. Combine flour and castor sugar in the Food
Processor. Blend on low speed and gradually
pour in combined milk, water and melted
butter. Blend until ingredients are mixed
together.
2. Transfer batter to a bowl and leave for at least
1 hour. Mixture will be quite thin.
3. Brush a non-stick fry pan with melted butter,
add approx 2 tablespoons of the mixture and
swirl around until base of pan is coated. Cook
for 2 minutes or until golden brown then turn
carefully flip with a plastic spatula and cook the
second side.
4. Remove carefully and transfer to a warmed
plate, cover with plastic film.
5. Continue to cook the remaining crepes as
above and stack until required.
6. For the strawberry puree, roughly chop or slice
strawberries and place in the small processor
bowl with the sugar. Puree to preferred
consistency.
7. Serve the crepes with strawberry puree and
strawberries.
7
Mini Cheese Cakes
Makes 6
INGREDIENTS
1 cup whole wheat biscuits
(such as Granita)
1 tsp mixed spices
2 tbsp melted butter
250g cream cheese
3 tbsp castor sugar
½ cup milk
3 eggs
½ cup light sour cream
1 tsp vanilla essence
1. Preheat the oven to 160°C, and lightly
grease flan tins or muffin tins.
2. To make the biscuit base, roughly break up
the biscuits and place in the Food Processor
bowl.
3. Add the mixed spice and process until
biscuits are crumbed using the pulse button.
4. Pour in melted butter and stir with a wooden
spoon until combined. Spread the base of the
tins with the crumb mixture.
5. To make the filling, spoon the cream cheese
into the Food Processor bowl. Add the sugar
and milk and process on a low speed until
just mixed. Add the eggs and process until
well combined. Add the sour cream and
vanilla and process until all ingredients are
mixed thoroughly to a smooth consistency.
6. Pour the cream cheese filling over the biscuit
bases and smooth the surface.
7. Bake in the oven for 40-45 minutes, or until
golden and lightly firm to touch.
8. Turn off the heat and leave in the oven for
another hour to prevent cracking.
9. Chill in the refrigerator until ready to serve.
10. Serve with berries and cream.
8
Berry Fruit Smoothie
Serves 2
INGREDIENTS
300ml apple juice
90g raspberries
1. Put all ingredients into the Blender jug. Blend
at low speed for 15 seconds, then high speed
for 15 seconds.
12 strawberries
4 ice cubes
Banana Nut Smoothie
Serves 2
INGREDIENTS
150g hazelnut yoghurt
1 large banana, roughly
chopped
1. Put all ingredients into the Blender jug, ice
cubes last. Blend at low speed for 10 seconds,
then high speed for 5 seconds.
200ml milk
6 ice cubes
Mango Lassi
Serves 2
INGREDIENTS
200ml natural yoghurt
1 ripe mango
200ml milk
2 tsp honey
1. Peel the mango, remove the flesh from the
stone and chop the flesh roughly.
2. Put all ingredients into the Blender jug. Blend
at low speed for 10 seconds, then high speed
for 5 seconds.
10 ice cubes
9
Banana, Vanilla & Honey Smoothie
Serves 2
NGREDIENTS
400ml milk
1 large banana, roughly chopped
1. Put all ingredients into the Blender jug. Blend
at low speed for 10 seconds, then high speed
for 10 seconds.
4 tsp honey
2 tsp vanilla essence
6 ice cubes
Chocolate Shake
Serves 2
INGREDIENTS
400ml milk
2 scoops chocolate ice
cream
1. Put all ingredients into the Blender jug. Blend
at low speed for 10 seconds, then high speed
for 10 seconds.
4 tbsp chocolate syrup
Tropical Cocktail
Serves 2
INGREDIENTS
1. Roughly chop the melon.
200ml ginger beer
2. Put all ingredients into the Blender jug. Blend
at low speed for 10 seconds, then high speed
for 10 seconds
150g melon flesh
40ml rum
5 ice cubes
10
La Mumba
Serves 2
INGREDIENTS
300ml chocolate milk
50ml brandy
1. Put all ingredients into the Blender jug. Blend
at low speed for 10 seconds, then high speed
for 5 seconds.
3 ice cubes
Pina Colada
Serves 2
INGREDIENTS
250ml pineapple juice
60ml Malibu
1. Put all ingredients into the Blender jug. Blend
at low speed for 15 seconds, then high speed
until smooth.
(White rum)
60ml coconut cream
3 ice cubes
Mango & Rum Cocktail
Serves 2
INGREDIENTS
100ml pineapple juice
½ ripe mango, stone
removed, peeled and roughly
chopped
1. Put all ingredients into the Blender jug, ice
cubes last. Blend at low speed for 10 seconds,
then high speed for 10 seconds.
1 small banana, roughly
chopped
40ml rum
3 tbsp natural yoghurt
5 ice cubes
11
Strawberry Gin Fizz
Serves 2
INGREDIENTS
100ml lemonade
60ml gin
1. Put all ingredients into the Blender jug, ice
cubes last. Blend at low speed for 10 seconds,
then high speed for 10 seconds.
1 tsp lemon juice
6 strawberries
5 ice cubes
Irish Cream Cocktail
Serves 2
INGREDIENTS
100ml milk
40g vanilla ice cream
1. Put all ingredients into the Blender jug, ice
cubes last. Blend at low speed for 10 seconds,
then high speed for 10 seconds.
½ tsp instant coffee
40ml Baileys or
Irish cream liqueur
3 ice cubes
12