Extron electronics | MTP U T A D | MTP U T A D • Setup Guide

NT: plete
RTAfor the coomns, and
O
P
m
o
M
I tron.c instructi ng the
.ex
on
ecti .
www stallati
e
conn
Go to uide, in s before er sourc
g
n
ow
p
e
user cificatio
th
to
e
t
p
s
uc
prod
MTP U T A D • Setup Guide
This guide provides quick start instructions for an experienced installer to set up and operate an Extron MTP U T A D universal transmitter.
Preparing the Mounting Surface
NOTE:
Use a wall box with a depth of at least 2.5 inches (6.4 cm).
1. Place the wall box against the installation surface and mark the opening guidelines.
TIP:Use a level to properly orient the opening.
5
2. Cut out the material from the marked area.
INPUTS
S-VIDEO
3. Secure the wall box with 10-penny nails or #8 or #10 screws, leaving the front edge flush with the outer wall or VIDEO
furniture
surface.
CONTACT
PRE-PEAK
50Hz REFRESH
PWR VID S-VID YUV PC
4
4. Run all required cables (see Rear Panel Connections) and secure them with cable clamps.
YUV
Y
AUDIO INPUT
7
ON
INPUTS
Pr
R
Plug a VGA monitor into the Monitor Out 15-pin HD connector.
c
Plug a high definition or standard definition component video source into the YUV RCA
connectors.
YUV
Y
7
AUDIO
L
Pb
3
6
COMPUTER INPUT
2 3
1
1
EDID SELECT
1
EF 2
R
0
Pr
3456
9A
78
MONITOR OUT
D
BC
Plug a composite video source into the Video RCA connector.
e
Plug an S-video source into the S-video 4-pin mini-DIN connector.
f
Plug a stereo audio source into the audio RCA connectors.
g
Plug a stereo audio source into the 3.5 mm mini jack connector.
2
6
Rear Panel Connections
j
2
AUDIO INPUT
ON
d
i
MONITOR OUT
PWR VID S-VID YUV PC
CONTACT
PRE-PEAK
50Hz REFRESH
4
b
h
S-VIDEO
D
BC
VIDEO
3456
0
Plug a computer (VGA) video source into the Computer Input 15-pin HD connector.
1
EDID SELECT
9A
78
a
5
Pb
3
COMPUTER INPUT
2 3
1
1
EF 2
Front Panel Inputs
AUDIO
L
OUTPUT
12V
.5A MAX
Terminate a TP cable as shown below at right. Connect it between the transmitter Output port
and the receiver Input port (both ends need to match).
Wire the 5-pole captive screw connector for the contact closure control of input selections
as shown below. To select a video input as the transmitter output, momentarily tie the
assigned pin for that format to ground.
Wire the 2-pole captive screw connector for the included external 12 VDC, 1 A power supply
(see image and grounding instructions on the next page).
ATTENTION:
network.
1 2 3 4
OUTPUT
8
Pin
Format
Pin
Format
Pin
Ground
1
Composite
3
YUV
5
Ground
2
S-video
4
PC
Pin
Pins:
12345678
8
Do not connect these devices to a computer or telecommunications
Contact closure input selection connector wiring:
9
10
12V
.5A MAX
Insert Twisted
Pair Wires
T568A1 2
Wire color
1 White-green
3 4
9
T568B
Wire color
10
White-orange
2 Green
Orange
3 White-orange
White-green
4 Blue
Blue
5 White-blue
White-blue
6 Orange
Green
7 White-brown
White-brown
8 Brown
Brown
NOTE: If you are using an
Enhanced Skew-Free™ A/V
cable, use the TIA/EIA T568A
standard only.
Sid
MTP U T A D • Setup Guide
Grounding the Power Input Port
POWER
12V
xA MAX
Smooth
Extron MTP U T A D transmitters can be adversely affected by electrostatic discharge (ESD)
if they are not grounded correctly.
Ridges
A
To prevent malfunctions or product damage, an experienced installer can correctly ground
an Extron MTP U T A D transmitter product by inserting one end of the grounding wire to the
negative or ground pin on the power input connector (see the image on the right). Tie the
other end of the wire to an earth ground.
Rear
Panel
A
3/16"
(5 mm)
Max.
Plug the connector into the MTP U T A D transmitter.
If you have any questions about how to ground a product in a specific application, contact an
Extron technical support specialist.
Tie
Wrap
SECTION A–A
Power Supply
Output Cord
Ridges
Front Panel Switch Settings and LEDs
DIP Switches
•
Contact — Set this switch on (up) for contact closure control of the input selection. Set the switch off (down) for auto switch mode (the
transmitter automatically selects the highest format video input with a sync signal present).
•
Pre-Peak — View the image and set the Pre-Peaking switch for the best image quality to correct for long cable runs of the entire sytem
•
50 Hz Refresh — Set this switch on (up) for a 50 Hz refresh rate for the resolution selected by the EDID Select switch. Set this switch
off (down) for 60 Hz.
2 3
D
BC
•
EDID Select rotary switch — Set this switch to one of the positions below to select either the local monitor as the source of the EDID data
or a specific resolution.
•
Position 0 — The loop-through monitor (2, on the other side of this guide) is the source of the EDID data.
•
Position 1 - F — Specify a resolution. The table below identifies the switch positions and the associated resolutions. By default, the
vertical refresh rate for all resolutions is 60 Hz. The resolution can be set to 50 Hz using the Refresh DIP switch.
Position
Source or
Resolution
Position
Resolution
Position
Resolution
Position
Resolution
0
Local monitor
4
1280 x 768
8
1366 x 768
C
1680 x 1050
1
800 x 600
5
1280 x 800
9
1400 x 1050
D
1920 x 1080
2
1024 x 768
6
1280 x 1024
A
1440 x 900
E
1920 x 1200
3
1280 x 720
7
1360 x 768
B
1600 x 1200
F
Not used
LEDs —
Wall Stud
•
Power — This LED indicates power is applied to the MTP.
•
Active input — The lit LED: PC, YUV, S-VID, or Vid; indicates the video input connector
that is selected for transmission.
Wall opening
is flush with
edge of box.
Cable Clamp
Final Installation
RGB
YUV
Y/C
SWITCH MODE
PRE-PEAK
REFRESH 50/60Hz
•
EO
2
0
2. At the power outlet, unplug the power supply.
DIOL
AU
UT
INP
T
OR
OU
NIT
MO
Pb
R
Pr
MTP U T A D
Decora
Faceplate
Transmitter
3. Mount the transmitter into the wall box, and attach the supplied Decora faceplate to the unit.
INP
ER
UT
MP
CO
3
DDC
OL.
RES
7
456
89A B
1. Make all connections, test the system, and install the device when operation is satisfactory.
V Y
YU
UT
DIO
AU
ON
1
Installation
Cable
VID
R
PW
TS O
PUS-VIDE
IN
VID
F 123
1
EF 2
0
9A
78
3456
DE
EDID
SELECT
C
CONTACT
PRE-PEAK
50 Hz REFRESH
•
ON
1
Earth
Ground
4. At the power outlet, reconnect the power supply.
Extron Headquarters
+800.633.9876 Inside USA/Canada Only
Extron USA - West
Extron USA - East
+1.714.491.1500+1.919.850.1000
+1.714.491.1517 FAX
+1.919.850.1001 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
Extron Asia
+800.7339.8766
Inside Asia Only
+31.33.453.4040
+31.33.453.4050 FAX
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+4000.EXTRON
+4000.398766
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
Extron Korea
+971.4.299.1800
+971.4.299.1880 FAX
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
Inside India Only
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2013 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
68-1674-50 Rev. D
01 13
Download PDF