RW-4
11/06
QUESTIONS OR CONCERNS CONTACT CANARM AT:
1-800-265-1833 (English)
1-800-567-2513 (French)
Monday through Friday 8:00 AM to 5:00 PM E.S.T.
TOOLS AND MATERIALS REQUIRED:
Wiring supplies as required by electrical code
Blade
Screwdriver
Wire Cutters
SAFETY PRECAUTIONS:
1. TURN OFF ELECTRICAL POWER BEFORE STARTING INSTALLATION OF LIGHT FIXTURE.
DO NOT REMOVE INSULATION FROM FIXTURE.
2. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE
BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
NOTE: Product May Not Look Exactly As Shown In Figures.
INSTALLATION:
STYLE#1
Studs
“A”
“B”
1.
Note: Refer to the mounting bracket style that matches the bracket that is included with your fixture.
STYLE#1 (Non-Threaded holes)
Loosen hex nut “A” and “B”. Adjust
STYLE#2
Screw
Fixture
Style #2 - Insert one screw into the mounting bracket - do not tighten yet. Tuck electrical wires into outlet box and position fixture over the mounting bracket. Line up the screw in the bracket to to the "7" hole on the fixture. Slide fixture to secure in place. Insert remaining screw. Tighten both screws to secure.
STYLE#2
STYLE#3
Nipple
Studs
“B” stud so it clears the fixture once assembled. Hold in place with “A” and lock in place with “B”.
STYLE#2 (Threaded holes)
Loosen “B”. Adjust stud to desired length and lock in place with “B”.
STYLE#3 (Nipple)
Attach nipple to mounting bracket and adjust until it will clear fixture when assembled. Lock in place using the hex nut.
Bracket
STYLE#1
Spinner
Nut
Glass
Tool
Fixture
Socket
5.
Note: Refer to the style of assembly that matches the style of your fixture.
STYLE#1 - Remove spinner nut from socket. Position glass on the
Hex Nut
STYLE #1
STYLE #2
Outlet
Box
Ground
Wire
Mounting
Bracket
Outlet Box
Screws
White
STYLE#3
Outlet
Box
2.
Attach ground wire on mounting bracket assembly to outlet box ground screw. Mount the mounting bracket to outlet box using outlet box screws. Make sure the studs or nipple on the mounting bracket are facing out from the outlet box.
3.
Connect black wire from fixture to black wire in outlet box and connect the white wire from fixture to white wire in outlet box.
STYLE#2
Thumb
Screws
STYLE #3
Knob
Socket
Holder
Bulb
Finial
Fixture
Head
Glass
Screw
Allen key
STYLE #4A STYLE #4B fixture and secure with spinner nut.
Install proper bulb type and wattage.
STYLE#2 - If required, place the decorative ring over the glass shade. Attach the glass shade to the fixture socket using the thumb screws (tighten with fingers only).
Install proper bulb type and wattage.
STYLE#3 - Install proper bulb type and wattage. Place the glass on the socket. Tighten the screw using the
Allen key (provided). Do not
over-tighten the screw. Keep the
Allen key for future use.
Fixture
Note: Do not disconnect wires that are already connected on the light.
Shade
If your fixture has shades,
STYLE#4A - Place shade on tube,
4.
STYLE#1- Tuck electrical wires
Bulb then install bulb.
STYLE#4B - Install bulb, shade then
Black into outlet box and position fixture
Tube finial.
STYLE#1
Cap
Nut over studs or nipple on mounting
STYLE#5
Glass
STYLE#5 - Install proper bulb
Stud
Or
Nipple
Fixture bracket assembly. Secure fixture in place with star washer(s) and cap nut(s).
Hole
For Stem type and wattage before assembling the glass. Remove ball screw from the curved stem.
Note: If required, assemble body and Position glass on lamp with the spread the arms of the fixture out
Ball Screw curved stem being inserted
Star
Washer evenly.
through the hole in the glass. Hand tighten the ball screw to secure the glass in place.
Imported By: CANARM LTD., 2157 Parkedale Ave., Brockville, Ontario, K6V 5V6, Tel: (613) 342-5424, Fax: (613) 342-8437