BBE Sound | 386 | Operating instructions | BBE Sound 386 Operating instructions

2-635-386-12(2)
LCD Colour TV
Operating Instructions
Before operating the TV, please read the “Safety
Information” section of this manual.
Retain this manual for future reference.
KLV-S19A10U
KLV-S19A10U
Printed in Spain
2-635-386-12(2)
© 2005 Sony Corporation
NOTICE FOR
CUSTOMERS
A moulded plug complying with BS1363 is fitted to this
equipment for your safety and convenience.
Should the fuse in the plug supplied need to be replaced, a 5
AMP fuse approved by ASTA or BSI to BS 1362 (i.e.,
marked with
or ) must be used.
When an alternative type of plug is used it should be fitted
with a 5 AMP FUSE, otherwise the circuit should be
protected by a 5 AMP FUSE at the distribution board.
If the plug supplied with this equipment has a detachable fuse
cover, be sure to attach the fuse cover after you change the
fuse. Never use the plug without the fuse cover. If you should
lose the fuse cover, please contact your nearest Sony service
station.
FUSE
How to replace the fuse
Open the fuse compartment with a blade screwdriver, and
replace the fuse.
WARNING
• To prevent the risk of electric shock, do not insert the plug
cut off from the mains lead into a socket outlet. This plug
cannot be used and should be destroyed.
• To prevent the risk of fire or electric shock, do not expose
the TV set to rain or moisture.
• Dangerously high voltages are present inside the TV set.
Do not open the cabinet. Refer servicing to qualified
personnel only.
2 GB
Introduction
Thank you for choosing this Sony product.
Before operating the TV, please read this manual
thoroughly and retain it for future reference.
Trademark information
• “PlayStation” is a trademark of Sony Computer
Entertainment, Inc.
• Licensed by BBE Sound, Inc. under USP4638258,
4482866. “BBE” and BBE symbol are trademarks of BBE
Sound, Inc.
• Manufactured under licence from Dolby Laboratories.
“Dolby,” “Pro Logic,” and the double-D symbol
are
trademarks of Dolby Laboratories.
Table of Contents
Safety information ....................................... 4
Precautions ................................................. 7
Overview of the remote ............................... 8
Overview of the TV buttons and
indicators................................................ 9
Getting Started
1: Checking the accessories ..................... 10
2: Inserting batteries into the remote......... 10
3: Connecting an aerial/VCR..................... 11
4: Preventing the TV from toppling over.... 12
5: Switching on the TV .............................. 12
6: Auto-tuning the TV ................................ 13
Watching TV
Watching TV.............................................. 14
Viewing pictures from connected
equipment ............................................ 16
PC Adjustment .................................................24
Timer menu ...............................................25
Sleep Timer ......................................................25
Set Up menu..............................................26
Auto Start Up....................................................26
Auto Tuning ......................................................27
Programme Sorting ..........................................27
Programme Labels ..........................................27
AV Preset .........................................................28
Manual Programme Preset ..............................29
Using Optional Equipment
Connecting optional equipment .................31
Additional Information
Specifications ............................................34
Troubleshooting .........................................36
Index ..........................................................38
GB
Using the Menu
Navigating through menus ........................ 16
Overview of the menus.................................... 17
Picture Adjustment menu .......................... 18
Picture Mode ................................................... 18
Contrast/Brightness/Colour/Hue/Sharpness/
Backlight .................................................... 18
Colour Tone..................................................... 18
Reset ............................................................... 19
Noise Reduction .............................................. 19
Sound Adjustment menu........................... 20
Sound Effect ................................................... 20
Treble/Bass/Balance ....................................... 20
Reset ............................................................... 20
Dual Sound...................................................... 21
Auto Volume .................................................... 21
Screen menu............................................. 22
Auto Format..................................................... 22
Screen Format................................................. 22
RGB Center ..................................................... 22
Features menu .......................................... 23
Power Saving .................................................. 23
Light Sensor .................................................... 23
AV2 Output ...................................................... 23
TV Speakers.................................................... 24
3 GB
Safety information
Mains lead
• Unplug the mains lead
when moving the TV
set. Do not move the
TV set with the mains
lead plugged in. It may
damage the mains lead
and result in fire or electric shock.
• If you damage the mains lead, it may
result in fire or electric shock.
– Do not pinch, bend, or twist the mains
lead excessively. The core
conductors may be exposed or
broken, causing a short-circuit, which
may cause fire or electric shock.
– Do not modify or damage the mains
lead.
– Do not put anything heavy on the
mains lead. Do not pull the mains
lead.
– Keep the mains lead away from heat sources.
– Be sure to grasp the plug when disconnecting the mains
lead.
• If the mains lead is damaged, stop using it and ask your
dealer or Sony service centre to exchange it.
• Do not use the supplied mains lead on any other
equipment.
• Use only an original Sony mains lead, not other brands.
Mains lead/cable protection
Pull out the mains lead/cable by
the plug. Do not pull on the mains
lead/cable itself.
Mains
Do not use a poor fitting mains socket. Insert the
plug fully into the mains socket. A poor fit may
cause arcing and result in fire. Contact your
electrician to have the mains socket changed.
Optional accessories
Observe the following when installing the
TV set using a stand or wall-mount bracket.
If you do not do so, the TV set may fall and
cause serious injury.
• It is strongly recommended that you use Sony accessories
for safety reasons:
–Wall-mount bracket SU-WL11,
• It is strongly recommended that you use the official Sony
wall-mount bracket to allow adequate air circulation and
to avoid dust build up around the TV, wall and ceiling.
• Secure the TV set properly, following the instructions
supplied with your stand or wall-mount bracket when
installing the TV set.
• Be sure to attach the brackets supplied with your stand.
4 GB
Installation
If the TV set is to be installed on a
wall, have the installation carried
out by qualified service men.
Improper installation may render
the TV set unsafe.
Medical institutions
Do not place this TV set in a place
where medical equipment is in
use. It may cause malfunction of
medical instruments.
Carrying
• Before carrying the TV set, disconnect
all the cables from the TV set.
• When you carry the TV set by hand,
hold the TV set as illustrated on the
right. If you do not do so, the TV set
may fall and be damaged or cause
serious injury. If the TV set has been
dropped or damaged, have it checked immediately by
qualified service personnel.
• When transporting it, do not subject the TV set to jolts or
excessive vibration. The TV set may fall and be damaged
or cause serious injury.
• When you carry the TV set in for repair or when you move
it, pack it using the original carton and packing material.
Ventilation
• Never cover the ventilation
holes in the cabinet. It may
cause overheating and result in
fire.
• Unless proper ventilation is provided, the TV set may
gather dust and get dirty. For proper ventilation, observe
the following:
– Do not install the TV set turned backwards or sideways.
– Do not install the TV set turned over or upside down.
– Do not install the TV set on a shelf or in a closet.
– Do not place the TV set on a rug or bed.
– Do not cover the TV set with cloth, such as curtains, or
items such as newspapers, etc.
• Leave some space around the TV set. Otherwise, aircirculation may be inadequate and cause overheating,
which may cause fire or damage to the TV set.
30 cm
10 cm
10 cm
SONY
Leave
at least
this
much
space.
• When installing the TV set on the wall, leave at least 10
cm space from the bottom of the TV set.
• Never install the TV set as follows:
Air circulation
is blocked.
Air circulation
is blocked.
Wall
Wall
Moisture and flammable objects
• Do not let this TV set get wet. Never
spill liquid of any kind on the TV set.
If any liquid or solid object does fall
through openings in the cabinet, do
not operate the TV set. It may result in
electric shock or damage to the TV set.
Have it checked immediately by
qualified service personnel.
• To prevent fire, keep flammable objects (candles, etc.) and
electric bulbs away from the TV set.
Oils
Do not install this TV set in restaurants that use oil. Dust
absorbing oil may enter and damage the TV set.
Fall
Ventilation holes
Do not insert anything in the ventilation
holes. If metal or liquid is inserted in these
holes, it may result in fire or electric shock.
Place the TV set on a secure, stable stand. Do
not hang anything on the TV set. If you do,
the TV set may fall from the stand or wallmount bracket, causing damage or serious
injury.
Do not allow children to climb on the TV set.
Vehicle or ceiling
Placement
• Never place the TV set in hot, humid
or excessively dusty places.
• Do not install the TV set where
insects may enter.
• Do not install the TV set where it
may be exposed to mechanical vibration.
• Place the TV set on a stable, level surface.
Otherwise, the TV set may fall and cause
injury.
• Do not install the TV set in a location
where it may protrude, such as on a
behind a pillar or where you might bump
your head on it. Otherwise, it may result
in injury.
Water and moisture
• Do not use this TV set near water
– for example, near a bathtub or
shower room. Also do not expose
to rain, moisture or smoke. This
may result in fire or electric shock.
• Do not touch the mains lead and the TV
set with set hands. Doing so may cause
electric shock or damage to the TV set.
Do not install this TV set in a
vehicle. The motion of the vehicle
may cause the TV set to fall down
and cause injury. Do not hang this
TV set from the ceiling.
Ships and other vessels
Do not install this TV set on a ship
or other vessel. If the TV set is
exposed to seawater, it may cause
fire or damage the TV set.
Outdoor use
• Do not expose the TV set to
direct sunlight. The TV set may
heat up and this may result in
damage to the TV set.
• Do not install this TV set
outdoors.
Wiring
• Unplug the mains lead when wiring cables. When hooking
up, be sure to unplug the mains lead for your safety.
• Take care not to catch your feet on the cables. It may
damage the TV set.
Cleaning
• Unplug the mains lead when cleaning the
mains plug and this TV set. If you do not,
it may result in electric shock.
• Clean the mains plug regularly. If the
plug is covered with dust and it picks up
moisture, its insulation may deteriorate
and result in fire.
Lightning storms
For your own safety, do not touch any
part of the TV set, mains lead, or
aerial lead during lightning storms.
Continued
5 GB
Damage requiring service
If the surface of the TV set cracks, do not touch it until you
have unplugged the mains lead. Otherwise electric shock
may result.
Servicing
Do not open the cabinet. Entrust the
TV set to qualified service personnel
only.
Small accessories removal and
fittable
Keep accessories out of children’s reach. If they are
swallowed, choking or suffocation may occur. Call a doctor
immediately.
Broken glass
Do not throw anything at the TV set. The
screen glass may explode by the impact
and cause serious injury.
When not in use
For environmental and safety
reasons, it is recommended that
the TV set is not left if standby
when unused. Disconnect from
the mains. However, some TV
sets may have features which need the TV set to be left in
standby to work correctly. The instructions in this manual
will inform you if this applies.
Viewing the TV
• To view the TV comfortably, the recommended viewing
position is from four to seven times the screen’s vertical
length away from the TV set.
• View the TV in moderate light, as viewing the TV in poor
light strains your eyes. Watching the screen continuously
for long periods of time can also strain your eyes.
• If the angle of the TV set is to be adjusted, steady the base
of the stand with your hand to prevent the TV set from
becoming separated from the stand. Be careful not to get
your fingers caught between the TV set and the stand.
Volume adjustment
• Adjust the volume so as not to trouble your neighbours.
Sound carries very easily at night time. Therefore, closing
the windows or using headphones is suggested.
• When using headphones, adjust the volume so as to avoid
excessive levels, as hearing damage may result.
Overloading
This TV set is designed to operate on
a 220–240 V AC supply only. Take
care not to connect too many
appliances to the same mains socket
as this could result in fire or electric
shock.
Heat
Do not touch the surface of the TV set. It remains hot, even
after the TV set has been turned off for some time.
Corrosion
If you use this TV set near the seashore, salt may corrode
metal parts of the TV set and cause internal damage or fire.
It may also shorten the life of the TV set. Steps should be
taken to reduce the humidity and moderate the temperature
of the area where the TV set is located.
6 GB
Precautions
LCD Screen
• Although the LCD screen is made with high-precision
technology and 99.99% or more of the pixels are effective,
black dots may appear or bright points of light (red, blue,
or green) may appear constantly on the LCD screen. This
is a structural property of the LCD panel and is not a
malfunction.
• Do not expose the LCD screen surface to the sun. Doing
so may damage the screen surface.
• Do not push or scratch the front filter, or place objects on
top of this TV set. The image may be uneven or the LCD
panel may be damaged.
• If this TV set is used in a cold place, a smear may occur in
the picture or the picture may become dark.
This does not indicate a failure. These phenomena
disappear as the temperature rises.
• Ghosting may occur when still pictures are displayed
continuously. It may disappear after a few moments.
• The screen and cabinet get warm when this TV set is in
use. This is not a malfunction.
• The LCD contains a small amount of liquid crystal and
mercury. The fluorescent tube used in this TV set also
contains mercury. Follow your local ordinances and
regulations for disposal.
Fluorescent lamp
This TV set uses a special fluorescent lamp as its light
source. If the screen image becomes dark, flickers, or does
not appear, the fluorescent lamp has worn out and the LCD
screen should be replaced. For replacement, consult qualified
service personnel.
Installing the TV set
• Do not install the TV set in places subject to extreme
temperature, for example in direct sunlight, or near a
radiator, or heating vent. If the TV set is exposed to
extreme temperature, the TV set may overheat and cause
deformation of the casing or cause the TV set to
malfunction.
• The TV set is not disconnected from the mains when the
TV set is switched off. To disconnect the TV set
completely, pull the plug from the mains.
• To obtain a clear picture, do not expose the screen to direct
illumination or direct sunlight. If possible, use spot
lighting directed down from the ceiling.
• Do not install optional components too close to the TV set.
Keep optional components at least 30 cm away from the
TV set. If a VCR is installed in front of the TV set or
beside the TV set, the picture may become distorted.
• Picture distortion and/or noisy sound may occur if the TV
set is positioned in close proximity to any equipment
emitting electromagnetic radiation.
Handling and cleaning the screen surface/
cabinet of the TV set
The screen surface is finished with a special coating to
prevent strong light reflections.
To avoid material degradation or screen coating degradation,
observe the following precautions.
• Do not push on the screen, scratch it with a hard object, or
throw anything at it. The screen may be damaged.
• Do not touch the display panel after operating the TV set
continuously for a long period as the display panel
becomes hot.
• We recommend that the screen surface be touched as little
as possible.
• To remove dust from the screen surface/cabinet, wipe
gently with a soft cloth. If dust is persistent, wipe with a
soft cloth slightly moistened with a diluted mild detergent
solution. You can wash and repeatedly use the soft cloth.
• Never use any type of abrasive pad, alkaline/acid cleaner,
scouring powder, or volatile solvent, such as alcohol,
benzene, thinner or insecticide. Using such materials or
maintaining prolonged contact with rubber or vinyl
materials may result in damage to the screen surface and
cabinet material.
• The ventilation holes can accumulate dust over time. To
ensure proper ventilation, we recommend removing the
dust periodically (once a month) using a vacuum cleaner.
Disposal of the TV set
Disposal of Old Electrical &
Electronic Equipment
(Applicable in the European
Union and other European
countries with separate
collection systems)
This symbol on the product or on
its packaging indicates that this
product shall not be treated as
household waste. Instead it shall
be handed over to the applicable
collection point for the recycling
of electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help prevent
potential negative consequences for the environment and
human health, which could otherwise be caused by
inappropriate waste handling of this product. The recycling
of materials will help to conserve natural resources. For more
detailed information about recycling of this product, please
contact your local city office, your household waste disposal
service or the shop where you purchased the product.
7 GB
Overview of the remote
1 TV "/1 – TV standby
Switches off the TV temporarily. The 1 (standby) indicator on the front of the
TV lights up. Press again to switch on the TV from the standby mode.
2
7
8
qa
1
3
4
5
6
2 % – Mute (page 14)
9
4
– Return to normal TV mode
5
– Screen mode (page 15)
6 Power Saving (page 23)
0
qs
qd
qf
qg
qh
qj
qk
ql
/
3
– Input select / Text hold
• In TV mode (page 16): Selects the input source from equipment connected to
the TV sockets.
• In Text mode (page 15): Holds the current page.
Reduces the power consumption of the TV.
7
– Picture mode (page 18)
8 9 – Sound effect (page 20)
9 Number buttons
• In TV mode: Selects channels. For channel numbers 10 and above, enter the
second digit within two seconds.
• In Text mode: Enters the three digit page number to select the page.
q;
Previous channel
Returns to the previous channel watched (for more than five seconds).
qa
/
– Info / Text reveal
• In TV mode: Displays information such as current channel number and screen
mode.
• In Text mode (page 15): Reveals hidden information (e.g., answers to a quiz).
qs Coloured buttons
Text mode (page 15): Used for Fastext.
qd / – Text (page 15)
qf M/m/</,/OK (page 14, 16)
qg Picture Freeze (page 15)
Freezes the TV picture.
qh Sleep Timer (page 25)
Sets the TV to stadby mode after a specified time period.
qj MENU (page 17)
qk PROG +/- (page 14)
• In TV mode: Selects the next (+) or previous (-) channel.
• In Text mode: Selects the next (+) or previous (-) page.
ql 2 +/- – Volume
Tip
The m/M/</,, PROG+, and number 5 buttons have tactile dots. Use the tactile dots as references when operating the TV.
8 GB
Overview of the TV buttons and indicators
1
2
1
2
3
4
5
6
3
(page 17)
– Input select (page 16)
Selects the input source from equipment
connected to the TV sockets.
OK MENU
4 2 +/-/ </,
• Increases (+) or decreases (-) the volume.
• In TV menu: Moves through the options left
(<) or right (,).
5 PROG +/-/ M/m
• In TV mode: Selects the next (+) or previous
(-) channel.
• In TV menu: Moves through the options up
(M) or down (m).
6 1 – Power
Switches the TV on or off.
7 Remote control sensor
8
SONY
–Sleep Timer (page 25)/
indicator (page 23)
Picture Off
• Lights up in amber when the “Sleep Timer” is set.
• Lights up in green when “Picture Off” is set.
9 1 – Standby indicator
Lights up in red when the TV is in standby mode.
q; ` – Power indicator
Lights up in green when the TV is switched on.
8
9
0
9 GB
Getting Started
1: Checking the
accessories
2: Inserting batteries
into the remote
Remote RM-EA002 (1)
Size AA batteries (R6 type) (2)
Mains Lead (1)
Bundling band (1) and screw (2)
AC Power adapter (1)
Notes
• Observe the correct polarity when inserting batteries.
• Dispose of batteries in an environmentally friendly way.
Certain regions may regulate disposal of the battery.
Please consult your local authority.
• Do not use different types of batteries together or mix old
and new batteries.
• Handle the remote with care. Do not drop or step on it, or
spill liquid of any kind onto it.
• Do not place the remote in a location near a heat source, or
in a place subject to direct sunlight, or in a damp room.
10 GB
Getting Started
3: Connecting an aerial/VCR
A
1
Coaxial cable
(not supplied)
Rear of the TV
3
Mains lead (supplied)
B
Rear of the TV
Coaxial
cable
(not
supplied)
1
2-1
3
PC
(SmartLink)
Y
PR/
CR
PB/
CB
Mains lead
(supplied)
L/G/
S/I
L/G/
S/I
RF lead
(not
supplied)
R/D/
D/D
R/D/D/D
Scart lead
(not supplied)
2-2
IN
OUT
VCR
11 GB
1
2
3
Connect your aerial with the coaxial cable.
If connecting to an aerial only (A)
Connect your aerial to the
socket on the rear of
the TV, then go to step 3.
If connecting to a VCR with an aerial (B)
Connect your aerial to the input socket on your VCR.
1 Connect the output socket on your VCR to the
socket on the rear of the TV with the RF lead.
2 Connect the scart socket on your VCR to the
/
2 scart socket on the rear of the TV
with a scart lead.
Connect the supplied mains lead to the AC
IN socket on the rear of the TV.
Do not connect the mains lead to your mains socket until
all connections are complete.
Bundle the cable.
4: Preventing the TV
from toppling over
After all connections are completed, secure the TV.
1
2
3
2
1
Connect your VCR.
Note
4
5: Switching on the TV
Fasten the supplied support belt to the
stand with a screw.
While supporting the TV, tighten the
supplied support belt to adjust the length.
Fit the supplied support belt to the TV
stand, then firmly fasten with the supplied
screw using a screw driver or coin, etc.
3
2
1
12 GB
SONY
1
2
Connect the TV to your mains socket (220240V AC, 50Hz).
Press 1 on the TV (Top side).
When you switch on the TV for the first time, the
language menu appears on the screen, then go to
“6: Selecting the language and country/region.
When the TV is in standby mode (the 1 (standby)
indicator on the front of the TV is red), press TV
+/1 on the remote to switch on the TV.
1
After selecting the language and country/region, a
message confirming the TV start auto-tuning appears
on the screen.
You must tune the TV to receive channels (TV
broadcasts). Do the following to search and store all
available channels.
Press OK to select “Yes”.
Getting Started
6: Auto-tuning the TV
Do you want to start
automatic tuning ?
Yes
No
m
Auto Tuning
Programmes found:
5
Searching...
The TV starts searching for all available channels.
This may take some time, please be patient and do
not press any buttons on the TV or remote.
Once all available channels have been stored, the
TV returns to normal operation, displaying the
channel stored on channel number 1.
When a message appears to confirm the aerial
connections:
No channels are found. Check all the aerial
connections and press OK twice to start
auto-tuning again.
1
2
3
4
4
The Programme Sorting menu appears on
the screen.
To change the order in which the channels
are stored on the TV. See page 27.
Press MENU to exit.
The TV has now tuned in all the available
channels.
13 GB
Watching TV
Watching TV
2
Press the number buttons or PROG
+/- to select a TV channel.
To select channel numbers 10 and above using the
number buttons, enter the second digit within two
seconds.
1
1
SONY
Additional operations
To
Do this
Turn off the TV
temporarily
(Standby mode)
Press TV "/1.
Turn on the TV from Press %. Press 2 +/- to set the
Standby mode
volume level.
without sound.
1
2
2
1
Press 1 on the TV (Top side) to switch on
the TV.
When the TV is in standby mode (the 1 (standby)
indicator on the front of the TV is red), press TV
"/1 on the remote to switch on the TV.
14 GB
Turn off the TV
completely
Press 1 on the top side of the
TV.
Adjust the volume
Press 2 + (increase)
/- (decrease).
Mute the sound
Press %. Press again to restore.
Return to the
previous channel
watched (for more
than five seconds)
Press
Access the
Programme index
table
Press OK. To select a channel,
press m/M, then press OK.
To access the Input
signal index table,
see page 16
Press OK. Press , to select
the desired input signal, press
m/M, then press OK.
.
To access Text
Tips
• Ensure that the TV is receiving a good signal, or some text
errors may occur.
• Most TV channels broadcast a Text service. For
information on the use of the service, select the index page
(usually page 100).
• When four coloured items appear at the bottom of the Text
page, Fastext is available. Fastext allows you to access
pages quickly and easily. Press the corresponding
coloured button to access the page.
• Whilst you are viewing Teletext, press
repeatedly to
choose between four different options of brightness.
change the screen mode manually to suit
the broadcast
Press
repeatedly to select Wide, Smart, 4:3, 14:9,
or Zoom.
Wide
Displays wide screen (16:9) broadcasts in the correct
proportions.
Smart*
Displays conventional 4:3 broadcasts with an
imitation wide screen effect. The 4:3 picture is
stretched to fill the screen.
4:3
Picture Freeze
Freezes the TV picture (e.g. to make a note of a
telephone number or recipe).
1 Press
on the remote control.
2 Press <,,,m,M to adjust the position of
the window.
3 Press
to remove the window.
4 Press
again to return to normal TV mode.
Displays conventional 4:3 broadcasts (e.g., non-wide
screen TV) in the correct proportions. As a result,
black border areas are visible on the screen.
14:9*
Displays 14:9 broadcasts in the correct proportions.
As a result, black border areas are visible on the
screen.
Zoom*
Displays cinemascopic (letter box format) broadcasts
in the correct proportions.
* Parts of the top and bottom of the picture may be cut off.
Tips
• Alternatively, you can set “Auto Format” to “On”. If the
broadcaster sends format information, the TV will
automatically select the best mode to suit the broadcast
(page 22).
• You can adjust the position of the picture when selecting
Smart, 14:9, or Zoom. Press m/M to move up or down
(e.g., to read subtitles).
15 GB
Watching TV
Press /. Each time you press /, the display changes
cyclically as follows:
Text t Text over the TV picture (mix mode) t No
Text (exit the Text service)
To select a page, press the number buttons or PROG
+/-.
To hold a page, press
/ .
To reveal hidden information, press
/ .
Return to normal TV mode
.
Viewing pictures from
connected equipment
Switch on the connected equipment, then
perform one of the following operation.
Using the Menu
Navigating through
menus
For equipment connected to the scart sockets using a
fully-wired 21-pin scart lead
Start playback on the connected equipment.
The picture from the connected equipment appears on
the screen.
For an auto-tuned VCR (page 11)
Press PROG +/-, or the number buttons, to select the
video channel. You can also press
/ repeatedly
until the correct input symbol (see below) appears on
the screen.
For other connected equipment
Press
/
repeatedly until the correct input
symbol (see below) appears on the screen or press OK
to access the Input signal index table. To select an input
source, press m/M, then press OK.
1/
1,
2/
2:
Audio/video or RGB input signal through the scart
socket
/
1 or 2. The symbol
appears only
if an RGB source has been connected.
2,3,4
4
3:
Component input signal through the Y, PB/CB, PR/CR
sockets
/
3, and audio input signal through the
L/G/S/I, R/D/D/D sockets
/
3.
4/
4:
Video input signal through the video socket
4, and
audio input signal through the audio socket L/G/S/I
(MONO), R/D/D/D sockets
4.
appears only if
the equipment is connected to the S video socket
4
instead of the video socket
4, and S video input
signal is input through the S video socket
4.
5:
RGB input signal through the PC connectors
audio input signal through the socket
.
5, and
Do this
Return to the normal Press
TV operation
Access the Input
Signal table
1
2
3
4
Additional operations
To
1
.
Press MENU to display the menu.
Press M/m to select a menu icon, then
press ,.
Press M/m to select an option.
Press M/m/</, to change/set the
setting, then press OK.
To exit the menu, press MENU.
To return to the last display, press <.
Press OK. To select an input
source, press m/M, then press OK.
Continued
16 GB
Overview of the menus
5
The following options are available in each menu. For
details on navigating through menus, see page 16.
Also, see page in parentheses for details of each menu.
Timer
Sleep Timer (25)
6
Set Up
Auto Start Up (26)
Auto Tuning (26)
Programme Sorting (27)
Programme Labels (27)
AV Preset (28)
– Label/Skip
Manual Programme Preset (29)
– Programme/Channel/Label/AFT/Audio
Filter/Skip/Confirm
Picture Adjustment
1
2
3
4
5
6
Picture Mode
Contrast
Brightness
Colour
Hue
Sharpness
Backlight
Co l ou r Tone
Reset
Noise Reduction
1
Set:
Auto
OK
End: MENU
Using the Menu
Select:
Custom
Max
50
50
0
15
5
Warm
Picture Adjustment
Picture Mode (18)
Contrast/Brightness/Colour/Hue/
Sharpness/Backlight (18)
Colour Tone (18)
Reset (19)
Noise Reduction (19)
2
Sound Adjustment
Sound Effect (20)
Treble/Bass/Balance (20)
Reset (20)
Dual Sound (21)
Auto Volume (21)
3
Screen
Auto Format (22)
Screen Format (22)
RGB Center (22)
4
Features
Power Saving (23)
Light Sensor (23)
AV2 Output (23)
TV Speakers (24)
PC Adjustment (24)
17 GB
Picture Adjustment menu
You can select the options listed below on the Picture
Adjustment menu. To select options, see “Navigating
through menus” (page 16).
Picture Adjustment
Picture Mode
Contrast
Brightness
Colour
Hue
Sharpness
Backlight
Colour Tone
Reset
Noise Reduction
Select:
Set:
Custom
Max
50
50
0
15
5
Warm
Tip
When you set the “Picture Mode” option to “Vivid” or
“Standard,” you can adjust only “Contrast,” and “Reset.”
Auto
OK
Back:
End: MENU
Picture Mode
Selects the picture mode.
1
Press OK to select “Picture Mode”.
2
Press m/M to select one of the following picture modes, then press OK.
• Vivid: For big lighted spaces.
• Standard: Optimal picture for home use.
• Custom: Allows you to store your own prefered settings.
Tip
You can change the picture mode by pressing
repeatedly.
Contrast/Brightness/Colour/Hue/Sharpness/Backlight
1
Press OK to select the option.
2
Press </, to set the level, then press OK.
Tip
“Hue” can only be adjusted for an NTSC colour signal (e.g., U.S.A. video tapes).
“Brightness”, “Colour”, “Hue”, “Sharpness” and “Backlight” only appear and can be adjusted if
“Picture Mode” is set to “Custom”.
Colour Tone
1
Press OK to select “Colour Tone”.
2
Press m/M to select one of the following, then press OK.
• Cool: Gives the white colours a blue tint.
• Neutral: Gives the white colours a neutral tint.
• Warm: Gives the white colours a red tint.
Tip
“Warm” only appears and can be adjusted if “Picture Mode” is set to “Custom”.
Continued
18 GB
Reset
Reset all the picture settings to the factory settings.
1
Press OK to select “Reset”.
2
Press m/M to select “OK,” then press OK.
Noise Reduction
Reduces the picture noise (snowy picture) in a weak broadcast signal.
1
Press OK to select “Noise Reduction”.
2
Press m/M to select “Auto”, then press OK.
Using the Menu
19 GB
Sound Adjustment menu
You can select the options listed below on the Sound
Adjustment menu. To select options, see “Navigating
through menus” (page 16).
Sound Adjustment
Sound Effect
Treble
Bass
Balance
Reset
Dual Sound
Auto Volume
Select:
Set:
Dynamic
0
0
0
A
Off
OK
Back:
End: MENU
Sound Effect
1
Press OK to select “Sound Effect”.
2
Press m/M to select one of the following sound effects, then press OK.
• Natural: Enhances clarity, detail, and sound presence by using “BBE High definition Sound
System*1.”
• Dynamic: Intensifies clarity and sound presence for better intelligibility and musical realism by
using the “BBE High definition Sound System.”
• Dolby Virtual*2: Uses the TV speakers to simulate the surround effect produced by a multi
channel system.
• Off: Flat response.
Tips
• You can change sound effect by pressing 9 repeatedly.
• If you set “Auto Volume” to “On”, “Soud Effect” changes to “Natural”.
*1
*2
Licensed by BBE Sound, Inc. under USP4638258, 4482866. “BBE” and BBE symbol are
trademarks of BBE Sound, Inc.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D
symbol
are trademarks of Dolby Laboratories.
Treble/Bass/Balance
Adjusts higher-pitched sounds (Treble), adjusts lower-pitched sounds (Bass), and
emphasizes left or right speaker balance (Balance).
1
Press OK to select the option.
2
Press </, to set the level, then press OK.
Reset
Resets the “Treble,” “Bass” and “Balance” settings to the factory settings.
1
Press OK to select “Reset”.
2
Press m/M to select “OK,” then press OK.
Continued
20 GB
Dual Sound
Selects the sound from the speaker for a stereo or bilingual broadcast.
1
Press OK to select “Dual Sound”.
2
Press m/M to select one of the following, then press OK.
• Stereo/Mono: For a stereo broadcast.
• A/B/Mono: For a bilingual broadcast, select “A” for sound channel 1, “B” for sound channel 2,
or “Mono” for a mono channel, if available.
Tip
If you select other equipment connected to the TV, set “Dual Sound” to “Stereo,” “A” or “B.”
Auto Volume
1
Press OK to select “Auto Volume”.
2
Press m/M to select “On,” then press OK.
Tip
If you set “Sound Effect” to “Dolby Virtual”, “Auto Volume” will automatically be switched to
“Off”.
21 GB
Using the Menu
Keeps a constant volume level even when volume level gaps occur (e.g., adverts tend to be
louder than programmes).
Screen menu
You can select the options listed below on the Screen
Control menu. To select options, see “Navigating
through menus” (page 16).
Screen
Auto Format
Screen Format
RGB Center
Select:
Set:
On
Smart
0
OK
Back:
End: MENU
Auto Format
Automatically changes the screen format according to the broadcast signal.
1
Press OK to select “Auto Format”.
2
Press m/M to select “On,” then press OK.
Tips
• Even if you have selected “On” or “Off” in “Auto Format”, you can always modify the format of
the screen by pressing
repeatedly.
• “Auto Format” is available for PAL and SECAM signals only.
Screen Format
For details about the screen format, see page 15.
1
2
Press OK to select “Screen Format”.
Press m/M to select “Wide,” “Smart,” “4:3,” “14:9” or “Zoom” (see
page 16 for details), then press OK.
RGB Center
Adjusts the horizontal picture position so that the picture is in the middle of the screen.
1
2
Press OK to select “RGB Center”.
Press </, to adjust the centre of the picture between -5 and +5, then
press OK.
Tip
This option is only available if an RGB source has been connected to the Scarts connectors
1/
1 or
2/
2 on the rear of the TV.
22 GB
Features menu
You can select the options listed below on the
Features menu. To select options, see “Navigating
through menus” (page 16).
Features
Power Saving
Light Sensor
AV2 Output
TV Speakers
PC Adjustment
Select:
Set:
Standard
On
TV
On
OK
Back:
End: MENU
Power Saving
Press OK to select “Power Saving”.
2
Press m/M to select one of the following, then press OK.
Using the Menu
1
• Standard: Default settings.
• Reduce: Reduces the power consumption of the TV.
• Picture Off: Switches off the picture. You can listen to the sound with the picture off.
Light Sensor
Automatically optimizes the picture settings according to the ambient light in the room.
1
Press OK to select “Light Sensor”.
2
Press m/M to select “On” then press OK.
AV2 Output
Sets a signal to be output through the socket labelled
/
2 on the rear of the TV. If
you connect a VCR to the
/
2 socket, you can then record from the equipment
connected to other sockets of the TV.
1
Press OK to select “AV2 Output”.
2
Press m/M to select one of the following, then press OK.
•
•
•
•
TV: Outputs broadcast from the aerial.
AV1: Outputs signals from equipment connected to the
AV4: Outputs signals from equipment connected to the
Auto: Outputs whatever is being viewed on the screen.
/
4/
1 socket.
4 socket.
23 GB
TV Speakers
Turns off the TV speakers e.g. to listen to the sound through external audio equipment
connected to the TV.
1
Press OK to select “TV Speakers”.
2
Press m/M to select one of the following, then press OK.
• On: the sound is output from the TV speakers.
• One Time Off: the TV speakers are temporarily turned off allowing you to listen to the
sound from external audio equipment.
Tip
The “TV speakers” option automatically returns to “On” when the TV set is switched off.
• Permanent Off: the TV speakers are permanently turned off allowing you to listen to
the sound from external audio equipment.
Tip
To turn on the TV speakers again, change to on.
PC Adjustment
Customizes the TV screen as a PC monitor.
1
Press OK to select “PC Adjustment”.
2
Press m/M to select one of the following, then press OK.
• Phase: Adjust the screen when a part of a displayed text or image is not clear.
• Pitch: Enlarges or shrinkes the screen size horizontally.
• H Center: Moves the screen to the left or to the right.
• V Center: Moves the screen up or down.
• Power saving: Turns to standby mode if no PC signal is received.
• Reset: Resets to the factory settings.
Tip
This option is only available if you are in PC Mode.
24 GB
Timer menu
You can select the options listed below on the Timer
menu. To select options, see “Navigating through
menus” (page 16).
Timer
Sleep Timer
Select:
Off
Set:
OK
Back:
End: MENU
Sleep Timer
1
2
Press OK to select “Sleep Timer”.
Press m/M to select the desired time period (“30min”/“60min”/“90min”/
“120min”), then press OK.
The
Tips
indicator on the TV (front) lights up in amber.
• If you switch off the TV and switch it on again, “Sleep Timer” is reset to “Off.”
• “Sleep timer will end soon. Power will be turned off.” appears on the screen one minute before
the TV switches to the standby mode.
• If you press
/ , the remaining time in minutes before the TV switches to the standby mode
is displayed on the screen.
25 GB
Using the Menu
Sets a period of time after which the TV automatically switches itself into the standby mode.
Set Up menu
You can select the options listed below on the Set Up
menu. To select options, see “Navigating through
menus” (page 16).
Set Up
Auto Start Up
Auto Tuning
Programme Sorting
Programme Labels
AV Preset
Manual Programme Preset
Select:
Set:
OK
Back:
End: MENU
Auto Start Up
Starts the “first time operation menu” to tune in all the available channels. Usually you do
not need to do this operation because the channels are already tuned when the TV was first
installed (page 13). However, this option allows you to repeat the process (e.g., to retune the
TV after moving house, or to search for new channels that have been launched by
broadcasters).
1
Press OK to select “Auto Start Up”.
2
Press M/m/</, to select the language, then press OK.
3
4
Press M/m to select the country/region in which you will operate the TV,
then press OK.
Press OK to select “Yes.”
The auto-tune display appears on the screen.
5
Follow steps 1 to 4 of “Auto-tuning the TV” (page 13).
Auto Tuning
Tunes in all the available channels.
Usually you do not need to do this operation because the channels are already tuned when
the TV was first installed (page 13). However, this option allows you to repeat the process
(e.g., to retune the TV after moving house, or to search for a new channels that have been
launched by broadcasters).
1
Press OK to select “Auto Tuning”.
2
Follow step 1 and 2 of “Auto-tuning the TV” (page 13).
When all available analogue channels have been tuned, the TV returns to normal
operation.
Continued
26 GB
Programme Sorting
Changes the order in which the channels are stored on the TV.
1
2
3
Press OK to select “Programme Sorting”.
Press M/m to select the channel you want to move to a new position,
then press OK.
Press M/m to select the new position for your channel, then press OK.
Repeat the procedure in steps 2 and 3 to move other channels if required.
Programme Labels
1
Press OK to select “Programme Labels”.
2
Press M/m to select the channel you want to name, then press OK.
3
Press M/m/</, to select the desired letter or number (“s” for a blank
space), then press OK.
If you input a wrong character
Press M/m/</, to select %/5 and press OK repeatedly until the wrong character is
selected. Then, press M/m/</, to select the correct character and press OK.
4
Repeat the procedure in step 3 until the name is complete.
5
Press M/m/</, to select “End,” then press OK.
27 GB
Using the Menu
Assigns a channel name of your choice up to five letters or numbers. The name will be
displayed briefly on the screen when the channel is selected. (Names for channels are usually
taken automatically from Analogue Text (if available).)
AV Preset
Do the following options.
1
Press OK to select “AV Preset”.
2
Press M/m to select the desired input source, then press OK.
3
Press OK. Then press M/m to select the desired option below, then
press OK.
Option
Description
Label
Assigns a name to any equipment connected to the side and rear
sockets. The name will be displayed briefly on the screen when the
equipment is selected.
Press M/m to select one of the following, then press OK.
AV1 (or AV2/AV3/AV4/PC/HDMI) VIDEO/DVD/CABLE/
GAME/CAM/SAT: Uses one of these preset labels.
Edit: Creates your own label. Follow steps 3 through 5 of
Programme Labels (page 27).
Skip:
Skips an input source that is not connected to any equipment when
you press M/m to select the input source.
After selecting this option, press OK.
Sound Offset:
Sets an independent volume level to each equipment connected to
the TV.
Press , to select “Sound Offset”, then press OK. Press M/m to
select the desired volume level.
Continued
28 GB
Manual Programme Preset
1
Press OK to select “Manual Programme Preset”.
Before selecting “Label”/“AFT”/“Audio Filter”/“Skip”/“Decoder”, press PROG +/- to
select the programme number with the channel. You cannot select a programme number
that is set to skip (page 30).
2
Press M/m to select one of the following options, then press OK.
Option
Description
Programme
Presets programme channels manually.
1
2
3
4
5
If you do not know the channel number (frequency)
Press M/m to search for the next available channel. When a
channel has been found, the search will stop. To continue
searching, press M/m.
If you know the channel number (frequency)
Press the number buttons to enter the channel number of the
broadcast you want or your VCR channel number.
6
7
Press OK.
Press OK to select “Confirm”, then press OK.
Repeat the procedure above to preset other channels manually.
29 GB
Using the Menu
Channel
Press M/m to select “Programme”, then press OK.
Press M/m to select the programme number you want
to manually tune (if tuning a VCR, select channel 0),
then press <.
Press M/m to select “Channel”, then press OK.
Press M/m to select “S” (for cable channels) or “C” (for
terrestrial channels), then press ,.
Tune the channels as follows:
Option
Description
Label
Assigns a name of your choice, up to five letters or numbers, to the
selected channel. This name will be displayed briefly on the screen
when the channel is selected.
1
2
AFT
Follow steps 3 to 5 of “Programme Labels” (page 27).
Press OK to select “Confirm”, then press OK.
Fine-tunes the selected programme number manually if you feel
that a slight tuning adjustment will improve the picture quality.
(Normally, fine tuning is performed automatically.)
1
2
Press M/m to adjust the fine tuning over a range of -15
to +15, then press OK.
Press OK twice.
To restore automatic fine tuning, select “On” in step 1.
Audio Filter
Improves the sound for individual channels in the case of distortion
in mono broadcasts. Sometimes a non-standard broadcast signal
can cause sound distortion or intermittent sound muting when
watching mono programmes.
1
Press M/m to select “Low” or “High”, then press OK.
If you do not experience any sound distortion, we recommend
that you leave this option set to the factory setting “Off”.
2
Press OK to select “Confirm”, then press OK.
Note
You cannot receive stereo or dual sound when “Low” or “High” is
selected.
Skip
Skips unused channels when you press PROG +/- to select
channels. (You can still select a skipped channel using the number
buttons.)
1
2
Press M/m to select “Yes”, then press OK.
Press OK to select “Confirm”, then press OK.
To restore a skipped channel, select “No” in step 1.
Continued
30 GB
Using Optional Equipment
Connecting optional equipment
You can connect a wide range of optional equipment to your TV. Connecting cables are not supplied.
Connecting to the side of the TV
C
Using Optional Equipment
A
S VHS/Hi8/DVC
camcorder
B
Headphones
To connect
Do this
S VHS/Hi 8/DVC
camcorder A
Connect to the S video socket
4 or the video socket
4,
and the audio sockets
4. To
avoid picture noise, do not connect
the camcorder to the video socket
4 and the S video socket
4 at the same time. If you
connect mono equipment, connect
to the L/G/S/I sockets
4, and
set “Dual Sound” to “A”
(page 21).
Headphones B
Connect to the i socket to listen to
sound from the TV on headphones.
To connect
Do this
Personal Computer Connect to the PC Input socket
5 and the audio socket G
C
on the rear of the TV (page 32).
Continued
31 GB
Connecting to the rear of the TV
DVD player
with component output
F
PC
Y
(SmartLink)
G
PR/
CR
PB/
CB
L/G/
S/I
L/G/
S/I
R/D/
D/D
R/D/D/D
H
Hi-Fi
D
PlayStation 2
E
DVD recorder / Hard disc recorder
VCR
Decoder
Decoder
DVD
32 GB
To connect
Do this
“PlayStation 2”,
DVD player or
decoder D
Connect to the scart socket
/
1. When you connect the
decoder, the scrambled signal from
the TV tuner is output to the
decoder, then the unscrambled
signal is output from the decoder.
DVD recorder or
VCR that supports
SmartLink E
Connect to the scart socket
/
2. SmartLink is a direct link
between the TV and a VCR/DVD
recorder. For more information on
SmartLink, refer to the instruction
manual supplied with your VCR or
DVD recorder.
DVD player with
component output
F
Connect to the component socket
3 and the audio sockets
3.
The component signal containing
576p signal format and audio
signal are input from the DVD
player.
Personal Computer See page 31.
G
Using Optional Equipment
Hi-Fi audio
equipment H
Connect to the audio output
sockets
to listen to the sound
from the TV on Hi-Fi audio
equipment. To turn off the sound
of the TV speakers, go to “TV
Speakers” on page 24.
33 GB
Additional Information
Specifications
•
•
Display Unit
Sound Output
Power Requirements:
220–240 V AC, 50 Hz
Screen Size:
19 inches
Display Resolution (horizontal x vertical):
1280 dots x 768 lines
Power Consumption:
56 W
Standby Power Consumption:
1W
Dimensions (w × h × d):
Approx. 468 x 402 x 218 mm (with stand)
Approx. 468 x 364 x 84 mm (without stand)
Weight:
Approx. 10,5 kg (with stand)
Approx. 7 kg (without stand)
5 W + 5 W (RMS)
Panel System
LCD (Liquid Crystal Display) Panel
TV System
I.
Colour System
PAL, SECAM
NTSC 3.58, 4.43 (only Video In)
Aerial
75 ohm external terminal for VHF/UHF
Channel Coverage
I:
UHF B21–B69
Terminals
•
•
•
•
•
AV1:
/
1
21-pin Scart connector (CENELEC standard) including
audio/video input, RGB input, and TV audio/video
output.
AV2:
/
2 (SMARTLINK)
21-pin Scart connector (CENELEC standard) including
audio/video input, RGB input, selectable audio/video
output, and SmartLink interface
AV3:
3
Y:1 Vp-p, 75 ohms, 0.3V negative sync
PB:0.7 Vp-p, 75 ohms
PR:0.7 Vp-p, 75 ohms
3 Audio input (phono jacks)
500 mVrms
Impedance: 47 kilo ohms
AV4:
4S video input (4-pin mini DIN)
4 Video input (phono jack)
4 Audio input (phono jacks)
AV5:
5
PC Input (15 Dsub) (see page 35)
G: 0.7 Vp-p, 75 ohms, non Sync on Green
B: 0.7 Vp-p, 75 ohms, non Sync on Green
R: 0.7 Vp-p, 75 ohms, non Sync on Green
HD: 1-5 Vp-p
VD: 1-5 Vp-p
PC audio input: minijack.
34 GB
Audio output (Left/Right) (phono jacks)
i Headphones jack
Supplied Accessories
•
•
•
•
•
Remote RM-EA002 (1)
Size AA batteries (R6 type) (2)
Support belt (1) and screw (2)
AC power adapter (1)
Mains Lead (1)
Optional Accessories
• Wall-Mount Bracket SU-WL11
Note
Remove Hinge Cover (cover for bundling the cables) before
removing Table Top Stand from the rear of the TV
(SU-WL11 Wall Mount Bracket instructions. Page 7, step 4,
point 1).
Design and specifications are subject to change
without notice.
PC Specifications
Horizontal
(Pixel)
Vertical
(Line)
Horizontal
frequency
(kHz)
Vertical
frequency
(Hz)
Standard
VGA
640
480
31.5KHz
60Hz
VGA
640
480
37.9KHz
72Hz
VESA
640
480
37.5KHz
75Hz
VESA
720
400
31.47KHz
70Hz
VGA-T
800
600
35.1KHz
56Hz
VESA Guidelines
800
600
37.9KHz
60Hz
VESA Guidelines
800
600
48.1KHz
72Hz
VESA
800
600
46.9KHz
75Hz
VESA
1024
768
48.4KHz
60Hz
VESA Guidelines
1024
768
56.5KHz
70Hz
VESA
1024
768
60.0KHz
75Hz
VESA
1280
768
47.40KHz
60Hz
VESA
1280
768
47.78KHz
60Hz
VESA
SVGA
XGA
WXGA
This TV does not support Sync on Green or Composite Sync.
If a signal other than in the above chart is input, it may not be displayed properly or may not be displayed as you set.
Using the Vertical frequency (Hz) of the personal computer at 60 is recommended.
35 GB
Additional Information
Signals
Troubleshooting
Check whether the 1 (standby) indicator is flashing in red.
When it is flashing
The self-diagnosis function is activated.
1 Measure how long the 1 (standby) indicator flashes and stops flashing.
For example, the indicator flashes for two seconds, stops flashing for one second, and flashes for two seconds.
2
Press 1 on the TV (top side) to switch it off, disconnect the mains lead, and inform your dealer or
Sony service centre of how the indicator flashes (duration and interval).
When it is not flashing
1 Check the items in the tables below.
2 If the problem still persists, have your TV serviced by qualified service personnel.
Picture
Cause/Remedy
No picture (screen is dark) and
no sound
• Check the aerial connection.
• Connect the TV to the mains, and press 1 on the TV (top side).
• If the 1 (standby) indicator lights up in red, press TV "/1.
No picture or no menu
information from equipment
connected to the scart
connector
• Check that the optional equipment is on and press
/
repeatedly until
the correct input symbol is displayed on the screen.
• Check the connection between the optional equipment and the TV.
Distorted picture
• When installing optional equipment, leave some space between the optional
equipment and the TV.
• When changing programmes or selecting Text, turn off any equipment
connected to the scart connector on the rear of the TV.
Double images or ghosting
• Check aerial/cable connections.
• Check the aerial location and direction.
Only snow and noise appear
on the screen
• Check if the aerial is broken or bent.
• Check if the aerial has reached the end of its serviceable life (three to five
years in normal use, one to two years at the seaside).
Picture (dotted lines or stripes)
noise
• Keep the TV away from electrical noise sources such as cars, motorcycles,
or hair-dryers.
• Make sure that the aerial is connected using the supplied coaxial cable.
• Keep the aerial cable away from other connecting cables.
• Do not use a 300-ohm twin lead cable as interference may occur.
Picture noise when viewing a
TV channel
• Select “Manual Programme Preset” in the “Set Up” menu and adjust “AFT”
(Automatic Fine Tuning) to obtain better picture reception (page 29).
• Select “Noise Reduction” in the “Picture Adjustment” menu to reduce the
noise in the picture (page 19).
Stripe noise during playback/
recording of a VCR
• Video head interference. Keep your VCR away from the TV.
• Leave a space of 30 cm between your VCR and the TV to avoid noise.
• Avoid installing your VCR in front of the TV or beside the TV.
Some tiny black points and/or
bright points on the screen
• The picture of a display unit is composed of pixels. Tiny black points and/or
bright points (pixels) on the screen do not indicate a malfunction.
36 GB
Additional Information
Problem
Problem
Cause/Remedy
No colour on programmes
• Select “Reset” in the “Picture Adjustment” menu to return to the factory
settings (page 19).
No colour or irregular colour
when viewing a signal from the
Y, PB/CB, PR/CR jacks of
3
• Check the connection of the Y, PB/CB, PR/CR jacks of
3.
3 are firmly seated in their
• Make sure that the Y, PB/CB, PR/CR jacks of
respective sockets.
Sound
Problem
Cause/Remedy
No sound, but good picture
• Press 2 +/– or % (Mute).
• Check that “TV Speakers” is set to “on” in the “Features” menu (page 24).
Noisy sound
• See the “Picture noise” causes/remedies on page 36.
General
Cause/Remedy
The TV turns off automatically
(the TV enters standby mode)
• If no signal is received or no operation is performed in the TV mode for 10
minutes, the TV automatically switches to standby mode.
Some input sources cannot be
selected
• Select “AV Preset” in the “Set Up” menu and cancel “Skip” of the input
source (page 30).
The remote does not function
• Replace the batteries.
Wrong characters appear
when viewing the menu/Text
• Select “Language” and “Country” in the “Set Up” menu and set the
language and country/region in which Text is provided (page 26). For
Cyrillic languages, we recommended that you select Russia if your own
country/region does not appear in the list.
Continued
37 GB
Additional Information
Problem
Index
Numerics
L
T
0-9 buttons 8
14:9 15
4:3 15
Label 29
Light Sensor 23
A
Manual Programme Preset 28
MENU button 8, 9
Mute (%) button 8
Noise Reduction 19
Number buttons 8
Text 15
Text (/) button 8, 38
Text hold ( ) button 8
Text reveal ( ) button 8
Timer indicator 9
Timer menu 25
Treble 20
TV mode (
) button 8
TV Speakers 24
TV (\) button 8
O
V
OK button 8, 9
Overview 8
Overview of the remote 8
VCR
connecting 11
Volume (2) +/- buttons 8, 9
P
W
Accessories supplied 10
Aerial, connecting 11
AFT 29
Audio Filter 30
Auto Format 22
Auto Start Up 26
Auto Tuning 13, 27
Auto Volume 21
Auto-tuning 13
AV Preset 28
AV2 Output 23
B
Backlight 18
Balance 20
Bass 20
Batteries, inserting into the remote 10
BBE 20
Brightness 18
C
Channel 29
Channels
auto-tuning 13
selecting 14
Skip 30
Checking the accessories 10
Colour 18
Colour Tone 18
Coloured buttons 8
Connecting 11
an aerial/VCR 11
optional equipment 31
Contrast 18
D
Dolby Virtual 20
Dual Sound 21
F
Fastext 15
Features menu 23
H
Headphones
connecting 31
Hue 18
I
Info ( ) button 8
Input select (
) button 8, 9
Input signal index table 16
38 GB
M
N
PC Adjustment 24
Picture Adjustment menu 18
Picture Freeze 8
Picture Mode 18
Picture mode ( ) button 8
Picture Off indicator 9
Power (\) indicator 9
Power Saving 8, 23
Previous channel 8
PROG +/- buttons 8, 9
Programme 29
Programme index table 14
Programme Labels 27
Programme Sorting 27
R
Remote
inserting batteries 10
overview 8
sensor 9
Reset
picture adjustment 19
sound adjustment 20
RGB Center 22
S
Screen Format 22
Screen menu 22
Screen mode 15
Screen mode (
) button 8
Set Up menu 26
Sharpness 18
Skip 30
Sleep Timer 8, 25
Smart 15
Sound Adjustment menu 20
Sound Effect 20
Sound effect (9) button 8
Specifications 34, 35
Standby (1) indicator 9
Standby 1 button 8
Wide 15
Z
Zoom 15
Download PDF