Yamaha | ISX-803 | Owner's Manual | OWNER’S MANUAL INTEGRATED AUDIO SYSTEM AB

AB
INTEGRATED AUDIO SYSTEM
OWNER’S MANUAL
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
i En
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
Install this unit in a well ventilated, cool, dry, clean place
– away from direct sunlight, heat sources, vibration, dust,
moisture and cold. For proper ventilation, allow the
following minimum clearances.
Top: 15 cm (6 in)
Rear: 2.5 cm (1 in)
Sides: 10 cm (4 in)
Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds.
Do not expose this unit to sudden temperature changes
from cold to hot (or vice versa), and do not locate this
unit in an environment with high humidity (i.e., a room
with a humidifier) to prevent condensation inside this
unit, which may cause an electrical shock, fire, damage to
this unit, and/or personal injury.
Avoid installing this unit where foreign object may fall
onto this unit and/or this unit may be exposed to liquid
dripping or splashing. On the top of this unit, do not
place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e., candles), as they may cause fire,
damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall and
liquid may cause electrical shock to the user and/or
damage to this unit.
Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If the
temperature inside this unit rises, it may cause fire,
damage to this unit, and/or personal injury.
Do not plug in this unit to a wall outlet until all
connections are complete.
Do not operate this unit upside-down. It may overheat,
possibly causing damage.
Do not use force on switches, knobs and/or cords.
When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cable.
Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
Only voltage specified on this unit must be used. Using
this unit with a higher voltage than specified is dangerous
and may cause fire, damage to this unit, and/or personal
injury. Yamaha will not be held responsible for any
damage resulting from use of this unit with a voltage
other than specified.
To prevent damage by lightning, keep the power cable
and outdoor antennas disconnected from a wall outlet or
this unit during a lightning storm.
Do not attempt to modify or fix this unit. Contact
qualified Yamaha service personnel when any service is
needed. The cabinet should never be opened for any
reasons.
When not planning to use this unit for long periods of
time (i.e., vacation), disconnect the AC power plug from
the wall outlet.
Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit
is faulty.
Before moving this unit, press
to set the system to off,
and disconnect the AC power plug from the wall outlet.
18 Condensation will form when the surrounding
temperature changes suddenly. Disconnect the power
cable from the outlet, then leave this unit alone.
19 When using this unit for a long time, this unit may
become warm. Turn the system off, then leave this unit
alone for cooling.
20 Install this unit near the wall outlet and where the AC
power plug can be reached easily.
21 The batteries shall not be exposed to excessive heat such
as sunshine, fire or the like.
– Keep the batteries in a location out of reach of
children. Batteries can be dangerous if a child were to
put in his or her mouth.
– If the batteries grow old, the effective operation range
of the remote control decreases considerably. If this
happens, replace the batteries with two new ones as
soon as possible.
– Do not use old batteries together with new ones.
– Do not use different types of batteries (such as
alkaline and manganese batteries) together. Read the
packaging carefully as these different types of
batteries may have the same shape and color.
– Exhausted batteries may leak. If the batteries have
leaked, dispose of them immediately. Avoid touching
the leaked material or letting it come into contact with
clothing, etc. Clean the battery compartment
thoroughly before installing new batteries.
– If you plan not to use the unit for a long period of
time, remove the batteries from the unit. Otherwise,
the batteries will wear out, possibly resulting in a
leakage of battery liquid that may damage the unit.
– Do not throw away batteries with general house
waste. Dispose of them correctly in accordance with
your local regulations.
This unit is not disconnected from the AC power source as
long as it is connected to the wall outlet, even if this unit
itself is turned off by . In this state, this unit is designed
to consume a very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
There is a chance that placing this unit too close to a CRTbased (Braun tube) TV set might impair picture color.
Should this happen, move this unit away from the TV set.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may result in
hazardous radiation exposure.
CONTENTS
NAMES OF PARTS AND THEIR FUNCTIONS.........................2
ADJUSTING THE CLOCK.........................................................5
INSTALLING “DTA CONTROLLER” ........................................6
LISTENING TO CD AND USB DEVICES ..................................7
LISTENING TO MUSIC FROM YOUR Bluetooth DEVICE.....10
LISTENING TO DAB STATIONS (ISX-803D) .........................13
LISTENING TO FM STATIONS ...............................................15
LISTENING TO EXTERNAL SOURCES .................................16
USING THE ALARM FUNCTION ............................................17
USING THE SLEEP TIMER .....................................................21
TONE CONTROL (REMOTE CONTROL ONLY) ....................21
ADJUSTING BRIGHTNESS OF FRONT PANEL DISPLAY ...21
TROUBLESHOOTING .............................................................22
NOTES ON DISCS AND USB DEVICES.................................25
SPECIFICATIONS ...................................................................26
• Play back music on external devices such as audio/data CDs and USB devices (USB flash drives), and tune in to the DAB (ISX-803D
only)/FM radio.
Français
Features
• By the Bluetooth technology, you can enjoy clear sound without wired connections. One touch pairing enabled by NFC technology.
• Store/call up to five of your favorite DAB (ISX-803D only)/FM stations easily.
Deutsch
• Use your favorite music or set of beeps as an alarm. The music you select is played at a volume of your own choice at the set alarm time,
giving you the best possible start to the day (IntelliAlarm function) (☞ P. 17).
• The 3-band equalizer (bass, middle, treble) can be set so that music sounds exactly how you want it.
• Two types of clocks (with hour hands) that match the design of the unit can be shown.
Svenska
‹ About this manual
• The illustrations of the main unit used in this manual are of the ISX-803D, unless otherwise specified.
• The DAB/DAB+ tuning feature is only available on the ISX-803D.
• If both the unit and remote control buttons can be used to operate a feature, the manual will describe steps using the buttons on the unit.
• Note indicates precautions for use of the unit and its feature limitations.
y
indicates supplementary explanations for better use.
Italiano
•
Supplied accessories
Power cable
Remote control
Batteries x 2
(AA, R6, UM-3)
FM antenna
(for ISX-803)
DAB/FM antenna
(for ISX-803D)
Español
USB cap
Owner’s Manual
(this manual)
Assembly Guide
Keep the USB cap out of
reach of children so as to
ensure that it is not
mistakenly swallowed.
Bracket
Pole
Base
Support
Cable clamp
Screw set
Note
Use these items to assemble the
stand. Read the separate
Assembly Guide for information
on how to assemble the stand.
Insert the batteries into the remote control in the correct direction
(+ and –).
Point the remote control at the remote control signal receiver (on
the front panel) and use within the range shown below.
6m
6m
(20')
1 En
Русский
How to use the remote control
Nederlands
Note
NAMES OF PARTS AND THEIR FUNCTIONS
Top panel
AUTO
2
SET
1
a
2
3 4
SOURCE + BEEP
BEEP
1
SOURCE
CLOCK
ALARM TYPE
USB
VOLUME
2
1
DIMMER
LABEL SIDE
SOURCE
ALARM
5 6
SNOOZE SLEEP
7
PRESET
8
9
j kl
m n
g SNOOZE/SLEEP
(Power)
Press to turn on the system or enter standby mode. Time is
displayed on the front panel even when the system is in standby
mode.
Set the sleep timer or switch the alarm to snooze mode
(☞ P. 19, 21).
h PRESET
y
• Press and hold
on the top of the unit for more than 3 seconds to set
the system to Eco Standby mode. No information on the front panel is
displayed in this mode. This can reduce power consumption. To cancel
Eco Standby mode, press
again.
Store/call up radio stations, or switch the playback folder
(when playing music on data CDs or USB devices).
i
NFC mark
j
Allows easy pairing with NFC technology.
c USB port
/
Skip the playback track/file, or tune the radio.
Holding the button down while playing a track/file will search
backward/forward the track/file.
• Even in standby mode or Eco Standby mode, the alarm function is
available.
b
DISPLAY
/
Play/pause the track being played.
k
Connect a USB device (☞ P. 9).
Eject the CD (☞ P. 7, 8).
d VOLUME –/+
l Disc slot
Adjust the volume.
Insert a CD (☞ P. 7, 8).
e SOURCE
m DAB information display (ISX-803D only)
Switch the source to be played.
Display DAB information (☞ P. 13).
f ALARM
Turns the alarm on/off, and allows various alarm settings to be
adjusted (☞ P. 18, 19).
n DISPLAY (ISX-803D only)
Switch the DAB information display (☞ P. 14).
‹ Auto Standby
• With the Auto Standby function, the unit behaves as described below when the system is turned on (default setting):
– This unit enters standby mode when playback of CD/USB is paused, when no signal is input from the tuner or a connected device, or when playback
continues at quite a low volume for a certain period of time (about 20 minuets).
– This unit enters standby mode when no operation is performed for more than 8 hours.
• Activating/Deactivating Auto Standby
1 1 Plug in the unit while pressing and holding
2 2 Keep holding
.
.
Auto Standby status changes, blinking the following indicators:
– When activating Auto Standby:
– When deactivating Auto Standby: Only
2 En
and the
, ALARM, and PRESET buttons on the top panel blink for 3 seconds.
on the front display blinks for 3 seconds.
NAMES OF PARTS AND THEIR FUNCTIONS
Front panel display
1 Play/shuffle/repeat indicator
1
Displays the playback mode (☞ P. 7, 9).
b Remote control signal receiver
c Clock indicator
2
3
9
4
8
Shows the clock hour hand (☞ P. 5).
d Source indicator
7
Shows selected source. (The DAB indicator is only displayed
on the ISX-803D.)
e Bluetooth indicator
Turns on if this unit is connecting via Bluetooth (☞ P. 10, 12).
f Sleep indicator
Turns on if the sleep timer has been set (☞ P. 21).
g Alarm indicator
Turns on if the alarm has been set (☞ P. 17).
The Weekly Alarm indicator (
) also turns on if Weekly
Alarm has been set.
5
h Multi-function indicator
6
Displays various information, including the clock time, track
number being played or FM station.
i Illumination sensor
Detects ambient lighting. Do not cover this sensor.
Rear panel
c DIMMER
6
Adjusts the brightness of the front panel display (☞ P. 21).
d AUX
1 2 3
Connects an external device.
e DAB/FM antenna terminal (ISX-803D)/
FM antenna terminal (ISX-803)
Connects the supplied DAB/FM antenna or an outdoor antenna.
75 Ω
AUX
75 Ω
75 Ω
AUX
Supplied
DAB/FM
antenna
DAB/FM ANT
AUX
DAB/FM ANT
FM ANT
75 Ω
AUX
4
4
5
5
ISX-803D
DAB/FM ANT
ISX-803D
ISX-803
Notes
• The antenna should be stretched out. If radio reception is poor, change
the height, direction, or placement of the antenna.
• If you use a commercially available outdoor antenna instead of the
supplied DAB/FM antenna, reception may be better.
a ALARM TYPE
Switches the alarm type (☞ P. 18).
b CLOCK
f Terminal cover
Remove the terminal cover before connecting external devices
to AUX, and/or connecting the DAB/FM antenna to antenna
terminal.
Switches the type of clock display or allows the time to be set
(☞ P. 5).
If you pass the outdoor antenna cable and/or external device cable through the pole of the stand, read the separate Assembly Guide.
3 En
NAMES OF PARTS AND THEIR FUNCTIONS
Remote control
a Remote control signal transmitter
1
b
2
(Power)
Press to turn on the system or enter standby mode.
3
c ALARM
Switches the alarm on/off.
4
d SNOOZE/SLEEP
Set the sleep timer or switch the alarm to snooze mode
(☞ P. 19, 21).
Bluetooth
e Source button
Switch the source to be played.
5
f
(Repeat)/
(Shuffle)
Play music on an audio/data CD or USB device in repeat/
shuffle (☞ P. 7, 9).
g
/
Switch the playback folder when playing music on data CDs or
USB devices.
6
h
7
8
Play/pause.
Apply the setting.
i
/
Skip the playback track/file.
Holding the button down while playing a track/file will search
backward/forward the track/file.
9
j
k
l
j
Stop playback.
k +10
m
n
Skip 10 tracks/files.
l VOLUME +/–
Adjust the volume.
o
p
q
m MUTE
Mute/resume the sound.
n EQ LOW/MID/HIGH
Adjust the bass, middle or treble sound quality (☞ P. 21).
o PRESET
/
Select a preset radio station.
p MEMORY
Store the radio station (☞ P. 15).
q TUNING
/
Tune the radio.
4 En
ADJUSTING THE CLOCK
Setting the time
1 Move the CLOCK switch on the rear panel to SET.
Top panel
AUTO
2
SET
2
Rear panel
SOURCE + BEEP
BEEP
1
1
SOURCE
DIMMER
CLOCK
ALARM TYPE
SET
USB
VOLUME
LABEL SIDE
SOURCE
ALARM
SNOOZE SLEEP
PRESET
2
2 Set the time with
/
.
Set time (flashing)
3 Move the CLOCK switch on the rear panel to
CLOCK1 or CLOCK2 to end the time setting.
y
• Pressing SNOOZE/SLEEP in step 2 will switch between the 12 and
24 hour clock display.
• The “PM” indicator will be shown only when you select the 12 hour clock
display.
Note
The time settings will be reset if the unit is not powered for more than one
week.
Switching the clock type
Move the CLOCK switch on the rear panel to switch the clock type.
‹ Clock display mode 1 (CLOCK 1)
Rear panel
Eg: 10:50
CLOCK 1
Analog clock
hour hand
(hour)
Minute
CLOCK 2
‹ Clock display mode 2 (CLOCK 2)
Eg: 10:50
Hour
Minute
5 En
INSTALLING “DTA CONTROLLER”
Installing DTA CONTROLLER application on a mobile device, such as a smartphone or tablet computer, allows you to use a variety of
additional convenient features of this unit.
Features
•
•
•
•
Turning on the unit or setting the unit to standby mode
Adjusting volume
Setting of the alarm function (IntelliAlarm) (☞ P. 20)
Playing back songs stored in an iPhone
The mobile device needs to be connected with the unit via Bluetooth connection (☞ P. 10).
Google PlayTM
http://itunes.com/app/dtacontroller
Note
If you cannot access the above information, search for “DTA CONTROLLER” on App Store or Google Play.
6 En
https://play.google.com/store/apps/
details?id=com.yamaha.av.
dtacontroller
LISTENING TO CD AND USB DEVICES
The unit will operate as follows when playing back tracks/files on CD/USB devices.
• If the CD/USB device being played back is stopped, the track that was being played back will start playing from the beginning of the
track the next time playback begins.
• If you press on the remote control while playback is stopped, the next time playback begins, the unit will play tracks as follows:
– For audio CD:
from the first track of the CD.
– For data CD/USB device: from the first track of the folder that contains the track that was played last.
• This system enters standby mode automatically if 20 minutes have elapsed without any playback and no operation is performed after
CD/USB device playback is stopped.
y
For details on playable discs and files, refer to “NOTES ON DISCS AND USB DEVICES” (☞ P. 25).
Listening to an audio CD
Use the following buttons to control the unit while playing
back tracks on audio CDs.
Top panel
AUTO
2
SET
2
Button
SOURCE + BEEP
BEEP
1
1
SOURCE
DIMMER
CLOCK
ALARM TYPE
Top
Panel
USB
Function
Play/Pause
/
Skip
/
LABEL SIDE
Search backward/forward
(press and hold down)
Eject the CD
VOLUME
SOURCE
ALARM
SNOOZE SLEEP
PRESET
Play/Pause
Skip
1
2
/
Remote
control
Search backward/forward
(press and hold down)
Stop
Repeat playback (☞ P. 9)
Shuffle playback (☞ P. 9)
1 Press SOURCE to set CD as the playback source.
+10
Skip 10 tracks/files
Note
CDs cannot be inserted or ejected when the system is in Eco Standby
mode (☞ P. 2).
Using the remote control
Press CD.
If a CD is already inserted, playback will start.
2 Insert the audio CD into the disc slot with the label
side facing toward the front of the unit.
Label side
Playback starts automatically. The track number is shown for a
while when starting playback or skipping tracks.
CD
Track number
7 En
LISTENING TO CD AND USB DEVICES
Listening to a data CD
Use the following buttons to control the unit while playing
back tracks on data CDs.
Top panel
AUTO
2
SET
2
Button
SOURCE + BEEP
BEEP
1
1
SOURCE
DIMMER
CLOCK
ALARM TYPE
Function
Play/Pause
/
Skip
USB
/
Top
Panel
LABEL SIDE
PRESET
VOLUME
SOURCE
ALARM
SNOOZE SLEEP
PRESET
Search backward/forward
(press and hold down)
Change the playback folder
Eject the CD
Play/Pause
1
Skip
2
1 Press SOURCE to set CD as the playback source.
/
Remote
control
Search backward/forward
(press and hold down)
Stop
/
Change the playback folder
Repeat playback (☞ P. 9)
Using the remote control
Press CD.
Shuffle playback (☞ P. 9)
If a CD is already inserted, playback will start.
2 Insert the data CD into the disc slot with the label
side facing toward the front of the unit.
Label side
Playback starts automatically. The folder/file number is shown
for a while when starting playback or skipping tracks.
Folder number
File number
8 En
+10
Skip 10 tracks/files within the
same folder
LISTENING TO CD AND USB DEVICES
Listening to a USB device
Use the following buttons to control the unit while playing
back tracks on USB devices.
Top panel
AUTO
2
SET
2
SOURCE + BEEP
BEEP
1
1
SOURCE
DIMMER
CLOCK
ALARM TYPE
Button
Function
Play/Pause
/
USB
VOLUME
SOURCE
ALARM
Skip
Top
Panel
LABEL SIDE
SNOOZE SLEEP
/
PRESET
PRESET
Search backward/forward
(press and hold down)
Change the playback folder
Play/Pause
Skip
2
/
1
Stop
Remote
control
1 Press SOURCE and set USB as the playback
Search backward/forward
(press and hold down)
/
Change the playback folder
Repeat playback (☞ P. 9)
source.
Shuffle playback (☞ P. 9)
Using the remote control
Press USB.
+10
If a USB device is already connected, playback will start.
2 Connect a USB device to the USB port.
Skip 10 tracks/files within the
same folder
y
Stop playback before removing the USB device.
Playback starts automatically. The folder/file number is shown
for a while when starting playback or skipping tracks.
Folder number
File number
Repeat/shuffle playback
The playback mode can be checked with the play/shuffle/repeat indicator on the front panel display.
‹ Repeat playback
Remote control
Repeat
Press
(Repeat) on the remote control to select a playback
mode from the following.
: 1 track
Shuffle
:
All tracks within the folder (data CD/USB device only)
: All tracks
y
No display: Repeat mode off
If the selected source contains folders, each folder will be played in repeat/
shuffle mode.
‹ Shuffle playback
Press
(Shuffle) on the remote control to select a playback
mode from the following.
:
All tracks within the folder (data CD/USB device only)
: All tracks
No display: Shuffle mode off
9 En
LISTENING TO MUSIC FROM YOUR Bluetooth DEVICE
This unit provides Bluetooth functionality. You can enjoy wireless music playback from your Bluetooth device (smartphone, digital audio
player, etc.). Please also refer to the owner’s manual of your Bluetooth device.
Pairing this unit with your Bluetooth device
Pairing is an operation that registers the communicating device (hereafter called “the connecting device”) with this unit. You’ll need to
perform the pairing operation the first time you use your Bluetooth device with this unit, or if the pairing settings have been deleted. Once
pairing has been completed, subsequent reconnection will be easy even after the Bluetooth connection is disconnected. If pairing is not
successful, refer to the item “Bluetooth” in “TROUBLESHOOTING” (☞ P. 23).
y
• This unit can be paired with up to eight connecting devices. When pairing with the ninth device has succeeded, pairing data for the device with the oldest
connection date will be deleted.
• If this unit is connected via Bluetooth to another device, hold down the SOURCE button on this unit or Bluetooth on the remote control to disconnect the
Bluetooth connection before you perform the pairing operation.
‹ If using an iPod touch/iPhone/iPad
1 Press the SOURCE button to switch the playback
Top panel
source to Bluetooth.
AUTO
2
SET
2
SOURCE + BEEP
BEEP
1
1
SOURCE
DIMMER
CLOCK
ALARM TYPE
Using the remote control
Press Bluetooth.
USB
2 On your iPod touch/iPhone/iPad, turn [Settings]
LABEL SIDE
[Bluetooth] on.
VOLUME
SOURCE
ALARM
SNOOZE SLEEP
PRESET
The Bluetooth connection list will appear in [Devices].
(This procedure or display may differ depending on the type of
your iPod touch/iPhone/iPad.)
3 From the Bluetooth connection list of the connecting
1
device, choose this unit (ISX-803 Yamaha/ISX-803D
Yamaha).
When pairing has been completed, your iPod touch/iPhone/
iPad will indicate “Connected”.
The Bluetooth indicator on the front panel display of this unit
will light.
Bluetooth indicator
‹ If using other than an iPod touch/iPhone/iPad
1 Press the SOURCE button to switch the playback
Top panel
source to Bluetooth.
AUTO
2
SET
2
SOURCE + BEEP
BEEP
1
1
SOURCE
DIMMER
CLOCK
ALARM TYPE
Using the remote control
Press Bluetooth.
USB
VOLUME
2 Perform Bluetooth pairing on the connecting device.
LABEL SIDE
SOURCE
ALARM
SNOOZE SLEEP
PRESET
For details refer to the owner’s manual of the connecting
device.
3 From the Bluetooth connection list of the connecting
1
Bluetooth indicator
device, choose this unit (ISX-803 Yamaha/ISX-803D
Yamaha).
When pairing has been completed, the Bluetooth indicator on
the front panel display of this unit will light for about 1
second.
y
If you are asked to enter a password, enter the numerals “0000”.
10 En
LISTENING TO MUSIC FROM YOUR Bluetooth DEVICE
‹ Easy pairing
For the smartphone with NFC (Near Field Communication) function, you can easily perform the pairing operation just by holding the
smartphone over the NFC mark (you need to turn the system on and turn on the NFC function of the smartphone beforehand).
1
Press
2
3
Hold the smartphone over the NFC mark.
to turn the system on.
Perform the pairing operation at the smartphone
(for details, please read the owner’s manual of the
smartphone).
This unit is indicated as “ISX-803 Yamaha”/“ISX-803D
Yamaha” on the smartphone.
y
• If you are prompted for a passkey, enter the numerals “0000”.
• If the connection fails, move the smartphone slowly on the NFC
mark.
• If the smartphone is equipped with a case, remove the case.
NFC
mark
Listening to a Bluetooth device
1 Press the SOURCE button to switch the playback
Top panel
source to Bluetooth.
AUTO
2
SET
2
SOURCE + BEEP
BEEP
1
1
SOURCE
DIMMER
CLOCK
ALARM TYPE
Using the remote control
Press Bluetooth.
USB
2 Connect this unit and your connecting device via
LABEL SIDE
Bluetooth.
VOLUME
SOURCE
1
ALARM
SNOOZE SLEEP
PRESET
3 Play back music from your Bluetooth device.
Note
Take care that the volume setting of this unit is not too high. We
recommend that you adjust the volume on the connecting device.
y
• If you connect via Bluetooth from your connecting device and play
back music while the system is in standby mode, the system will
automatically turn on.
• If you disconnect the Bluetooth connection from your connecting
device while the playback source is set to Bluetooth, the system will
automatically enter standby mode.
• If Bluetooth is selected as the playback source, the system will
automatically enter standby mode when 20 minutes have elapsed
without any Bluetooth connection nor any operation performed.
11 En
LISTENING TO MUSIC FROM YOUR Bluetooth DEVICE
Connecting an already-paired device via Bluetooth
Once pairing has been completed, connecting a Bluetooth will be easy the next time.
‹ Connecting from this unit
1 Press the SOURCE button to switch the playback
Top panel
AUTO
2
SET
2
SOURCE + BEEP
BEEP
1
1
SOURCE
DIMMER
CLOCK
ALARM TYPE
source to Bluetooth.
Using the remote control
Press Bluetooth.
USB
VOLUME
LABEL SIDE
SOURCE
ALARM
SNOOZE SLEEP
PRESET
1
Bluetooth indicator
The Bluetooth indicator will blink on the front panel display;
this unit will search for the connecting device that was most
recently connected via Bluetooth, and will then establish a
connection (You must first turn on the Bluetooth setting of the
connecting device).
When the Bluetooth connection has been established, the
Bluetooth indicator will light.
Note
Yamaha does not guarantee all connections between this unit and
Bluetooth device.
‹ Connecting from the connecting device
1 In the Bluetooth settings of the connecting device, turn Bluetooth on.
2 From the Bluetooth connection list of the connecting device, choose this unit (ISX-803 Yamaha/ISX-803D
Yamaha).
The Bluetooth connection will be established, and the Bluetooth indicator on the front panel display of this unit will light.
‹ Connecting with the NFC function
When using an already-paired smartphone with the NFC function, holding it over the NFC mark establishes a Bluetooth connection.
Note
Bluetooth connections cannot be established from the connecting device when this unit is in Eco Standby mode. Turn the system on.
Disconnecting a Bluetooth connection
If any of the following operations are performed while a Bluetooth connection is established, the Bluetooth connection will be disconnected.
• Hold down the SOURCE button on this unit or Bluetooth on the remote control.
• Set the system to standby mode.
• Turn off the Bluetooth setting of the connecting device.
• Hold the smartphone with the NFC function over the NFC mark during Bluetooth connection.
12 En
LISTENING TO DAB STATIONS (ISX-803D)
DAB (Digital Audio Broadcasting) and DAB+ use digital signals for clearer sound and more stable reception compared to analog signals.
DAB+ is based on the original DAB standard but uses a more efficient audio codec.
DAB and DAB+ are broadcast in blocks of data called “ensembles” containing up to several radio stations that are simultaneously broadcast.
DAB and DAB+ can also include an extensive amount of text information, enabling you to select a station by name.
Other information, such as the ensemble name or the status of the digital signal, can be displayed on the DAB information display.
“DAB” described in this manual may also refer to “DAB+”.
Preparing for DAB reception
Before tuning into DAB stations, an initial scan must be performed. When you select the DAB for the first time, the initial scan is performed
automatically.
1 Press SOURCE and set DAB as the playback source.
Top panel
AUTO
2
SET
2
The initial scan starts. During the scan, the degree of progress
is displayed on the DAB information display.
SOURCE + BEEP
BEEP
1
1
SOURCE
DIMMER
CLOCK
ALARM TYPE
LABEL SIDE
SOURCE
ALARM
SNOOZE SLEEP
Scan is completed.
“Completed” and the number of receivable DAB stations
appear on the DAB information display.
PRESET
1
1
Using the remote control
Press RADIO to switch between DAB/FM.
Note
• To perform the initial scan manually, press and hold PRESET for
more than 4 seconds and then press PRESET when the scan starting
screen is displayed.
• If the initial scan is performed, stored DAB station information and
preset DAB stations are cleared.
Tuning DAB stations
1 Press SOURCE and set DAB as the playback source.
2 Press / to tune the DAB station.
Top panel
AUTO
2
SET
2
SOURCE + BEEP
BEEP
1
1
SOURCE
DIMMER
CLOCK
ALARM TYPE
Using the remote control
Press TUNING
USB
VOLUME
/
LABEL SIDE
SOURCE
1
ALARM
SNOOZE SLEEP
While receiving DAB, switch on the DAB information display.
When the unit does not receive a DAB signal, “Off Air” is
displayed instead of the DAB station name.
PRESET
2
1
2
3
4
a Signal strength indicator:
Shows current signal strength.
b Secondary indicator:
Some stations have sub (secondary) stations. If a
secondary station is playing, the secondary indicator is
displayed.
c DAB station name
d DAB station Information (☞ P. 14)
13 En
LISTENING TO DAB STATIONS (ISX-803D)
Switching DAB station information
1 Select DAB information by pressing DISPLAY
Top panel
SET
2
repeatedly.
SOURCE + BEEP
BEEP
1
SOURCE
CLOCK
ALARM TYPE
Information is displayed in the order shown below.
LABEL SIDE
NOOZE SLEEP
PRESET
DISPLAY
Text information
¨ Ensemble name
( is displayed before the ensemble name.)
¨ Status 1 (channel label and frequency)
¨ Status 2 (DAB or DAB+ and signal quality)
¨ Back to the top.
1
Storing DAB stations (preset)
Use the preset function to store your favorite 5 stations.
1 Press / to tune into your favorite DAB station.
2 Press and hold down PRESET.
Top panel
AUTO
2
SET
2
SOURCE + BEEP
BEEP
1
1
SOURCE
DIMMER
CLOCK
ALARM TYPE
USB
LABEL SIDE
DAB
VOLUME
SOURCE
ALARM
SNOOZE SLEEP
PRESET
234
1
Preset
number
Using the remote control
Press and hold down MEMORY.
3 Press PRESET and select the preset number to
store the DAB station.
Using the remote control
Press PRESET
/
.
4 Press and hold down PRESET to store the preset
station.
This stores the DAB station.
Using the remote control
Press MEMORY.
Selecting preset DAB stations
1 Press SOURCE and set DAB as the playback
Top panel
AUTO
2
SET
2
SOURCE + BEEP
BEEP
1
1
SOURCE
DIMMER
CLOCK
ALARM TYPE
source.
2 Press PRESET repeatedly to select the preset DAB
station.
USB
LABEL SIDE
Using the remote control
Press PRESET
VOLUME
SOURCE
1
14 En
ALARM
SNOOZE SLEEP
PRESET
2
/
.
LISTENING TO FM STATIONS
Selecting the FM station
1 Press SOURCE and set FM as the playback source.
Top panel
AUTO
2
SET
2
SOURCE + BEEP
BEEP
1
1
SOURCE
DIMMER
CLOCK
ALARM TYPE
Reception
frequency
FM
USB
VOLUME
LABEL SIDE
SOURCE
ALARM
SNOOZE SLEEP
PRESET
Using the remote control
Press RADIO.
1
2
2 Press
/
to tune the FM station.
Tuning type
Note
If you tune to an FM station manually, the sound will be in monaural.
Top
panel
Remote
control
Operation
Automatic Press and hold down
tuning
or
.
Manual
tuning
Press
or
repeatedly.
Automatic Press and hold down
tuning
TUNING
or .
Manual
tuning
Press TUNING
repeatedly.
or
Storing FM stations (preset)
Use the preset function to store your favorite 5 stations.
1 Press
Top panel
AUTO
USB
2
SET
2
1
SOURCE
CLOCK
ALARM TYPE
to tune into your favorite FM station.
2 Press and hold down PRESET.
SOURCE + BEEP
BEEP
1
DIMMER
/
LABEL SIDE
FM
VOLUME
SOURCE
ALARM
SNOOZE SLEEP
Preset
number
PRESET
234
1
Using the remote control
Press and hold down MEMORY.
3 Press PRESET and select the preset number to
store the FM station.
Using the remote control
Press PRESET
/
.
4 Press and hold down PRESET to store the preset
station.
This stores the FM station.
Using the remote control
Press MEMORY.
15 En
LISTENING TO EXTERNAL SOURCES
Selecting a preset FM station
1 Press SOURCE and set FM as the playback source.
Top panel
AUTO
2
SET
2
2 Press PRESET repeatedly to select the preset FM
SOURCE + BEEP
BEEP
1
1
SOURCE
DIMMER
CLOCK
ALARM TYPE
station.
Using the remote control
USB
VOLUME
Press PRESET
LABEL SIDE
SOURCE
1
ALARM
SNOOZE SLEEP
/
.
PRESET
2
LISTENING TO EXTERNAL SOURCES
Set the system to standby mode before connecting audio cables.
Remove the terminal cover before connecting external devices.
Top panel
AUTO
2
SET
1
DIMMER
CL
1 Connect external audio device to AUX on the rear
panel using a commercially available 3.5 mm (1/8 in)
stereo mini plug cable.
USB
VOLUME
LAB
SOURCE
ALARM
75 Ω
SNOOZ
AUX
DAB/FM ANT
AUX
2
3
ISX-803D
75 Ω
AUX
FM ANT
ISX-803
Note
Turn down the volume of the unit and your external audio device before
connection.
2 Press to turn the system on.
3 Press SOURCE and set AUX as the playback
source.
Using the remote control
Press AUX.
4 Start playback on the connected external audio
device.
16 En
USING THE ALARM FUNCTION
The unit includes an alarm function (IntelliAlarm) that plays back music sources or set of beeps (built-in alarm) at the set time in a variety of
different methods. The alarm function has following features.
‹ 3 types of alarms
Select from 3 alarm types, combining music and beep sounds.
The selected audio source and beep sound are played at the set time. This mode is recommended for
the best possible start to the day.
SOURCE + BEEP
3 minutes before the set time: the source music begins to fade in and the volume gradually increases
as the alarm time approaches.
Alarm time:
a beeping sound also begins playing.
SOURCE
The selected audio source is played at the set time. The volume fades in gradually and increases to
the set volume.
BEEP
Only beep sound is played back at the set time.
‹ Various music sources
Audio CD, data CD, USB device and radio can be selected. The following can also be selected depending on the audio source:
Source
Playback method
Function
Selected track
The selected track is played repeatedly.
Resume
The track you listened to last time is played back.
Folder
The selected folder is played repeatedly.
Resume
The track you listened to last time is played back.
Preset station
The selected preset radio station is played.
Resume
The radio station you listened to last time is played back.
Audio CD
Data CD/USB
Radio
‹ Snooze
The snooze function can be enabled to replay the alarm after 5 minutes.
17 En
USING THE ALARM FUNCTION
Set the alarm time and alarm type
4 (when alarm types other than BEEP are selected)
Top panel
AUTO
SET
2
SOURCE + BEEP
BEEP
1
1
SOURCE
DIMMER
CLOCK
ALARM TYPE
USB
Press SOURCE to select music source.
Sources other than AUX and Bluetooth can be selected.
Using the remote control
Press the USB, CD, or RADIO button to select the
music source.
LABEL SIDE
SOURCE
VOLUME
6
2
ALARM
SNOOZE SLEEP
4 17
PRESET
5 2
Note
The alarm setting will be erased if the system enters standby mode without
properly completing it.
5 (when alarm types other than BEEP are selected)
Specify the track, folder or radio station to be
played.
Press PRESET to select the track (audio CD), folder (data
CD/USB device) or radio station to be played.
1 Press and hold ALARM.
The alarm indicator (
Notes
• If CD/USB has been selected, connect/insert the audio source (audio/
data CD, USB device) to the unit.
• If source cannot be played back at the time set for the alarm (eg. CD
is not inserted), the beep sound is played back.
) and set alarm time will flash.
Using the remote control
Press PRESET
/
.
y
Alarm time
When “0” is set, the playback resumes from the track/radio station you
listened to last time (resume).
Alarm indicator
6 Set the alarm volume by pressing VOLUME –/+.
2 Press
/
to set the alarm time.
Alarm volume
Using the remote control
Press
/
.
3 Select the alarm type with the ALARM TYPE
7 Press ALARM to complete setting the alarm.
switch on the rear panel.
For details on alarm types, refer to P. 17.
Rear panel
SOURCE+
BEEP BEEP
SOURCE
18 En
The alarm will be set, and the alarm indicator (
light up.
) will
USING THE ALARM FUNCTION
Turning the alarm on/off
1 Press ALARM.
Top panel
AUTO
2
SET
1
CLOCK
USB
VOLUME
2
1
DIMMER
When the alarm is on, the alarm indicator (
) is shown,
and the alarm time is shown for a while. If you press ALARM
again, the alarm indicator (
) and the alarm will turn off.
When alarm mode is Weekly Alarm (☞ P. 20), the Weekly
Alarm indicator (
) will also turn on/off.
BEEP
SO
ALAR
y
LABEL SIDE
SOURCE
ALARM
The alarm setting will be saved even if the alarm is turned off. If the
alarm is turned on again by pressing ALARM, the alarm will sound
with the previous alarm settings.
SNOOZE SLEEP
1
Operations while playing back alarm sound
At the set time, the alarm sound is played back. During playback, the following operations are available.
‹ Stopping the alarm for a short time (snooze)
1 Press SNOOZE/SLEEP.
Top panel
AUTO
2
SET
1
1
DIMMER
CLOCK
USB
VOLUME
2
BEE
A
ALARM
y
• When SOURCE + BEEP is set, press SNOOZE/SLEEP once to
stop the beep sound, and twice to stop the audio source. 4 minutes
after the audio source is stopped, it will start fading in again and after
another minute the beep sound will resume.
• The alarm indicator will flash when the snooze function is activated.
LABEL SIDE
SOURCE
SNOOZE will stop the alarm and resume again in 5 minutes.
SNOOZE SLEEP
1
‹ Turning the alarm off
1 Press ALARM or
Top panel
AUTO
USB
VOLUME
1
2
SET
2
1
1
DIMMER
CLOCK
BEE
A
.
y
• The alarm stops automatically after 60 minutes unless you stop the
alarm.
• The alarm setting will be saved even if the alarm is turned off. If the
alarm is turned on again by pressing ALARM, the alarm will sound
with the previous alarm settings.
LABEL SIDE
SOURCE
ALARM
SNOOZE SLEEP
1
19 En
USING THE ALARM FUNCTION
Setting Weekly Alarm
With DTA CONTROLLER (☞ P. 6), you can use Weekly Alarm, which allows you to set alarm times respectively for each day of the week.
First, make the Weekly Alarm settings on DTA CONTROLLER.
‹ Setting Weekly Alarm with DTA CONTROLLER
1 Tap
(IntelliAlarm icon) in DTA CONTROLLER
to open the IntelliAlarm setting screen.
IntelliAlarm setting screen
2 Perform the operations below on the IntelliAlarm
setting screen.
a Select [Week] (Weekly Alarm).
b Set the alarm time for each day of the week.
c Set the alarm volume or IntelliAlarm advanced settings.
d Tap [Sync] to transfer the settings to the unit.
The Weekly Alarm function is activated and the alarm
indicator (
) and Weekly Alarm indictor (
) turn
on.
Due to product improvements, specifications and appearance
are subject to change without notice.
‹ Setting Weekly Alarm on the unit
Once you have set Weekly Alarm by DTA CONTROLLER, you can select the Weekly Alarm mode in the alarm mode select display of this
unit.
1d (One Day Alarm mode):
An alarm that sounds only
once at the specified time.
Top panel
AUTO
2
SET
SOURCE + BEEP
BEEP
1
1
SOURCE
DIMMER
CLOCK
ALARM TYPE
USB
VOLUME
2
7d (Weekly Alarm mode):
An alarm whose time can be
specified for each day of the
week (settable only using
“DTA CONTROLLER”).
LABEL SIDE
SOURCE
ALARM
SNOOZE SLEEP
12
PRESET
2
1 Press and hold ALARM.
The alarm indicator (
) will flash and the alarm mode
select display will appear.
If you have chosen Weekly Alarm mode, this completes the
alarm setting. The alarm indicator (
) and the Weekly
Alarm indicator (
) will light up.
Weekly Alarm indicator
Alarm indicator
2 Select the alarm mode.
Press
/
confirm it.
to select the alarm mode, and press ALARM to
Using the remote control
Press
/
to select the alarm mode, and press
to confirm it.
20 En
Note
The Weekly Alarm mode cannot be selected when all the days of the
Weekly Alarm setting are turned off. Turn on any day of the Weekly
Alarm setting.
USING THE SLEEP TIMER
You can set the time until the system automatically enters standby mode.
1 Press SNOOZE/SLEEP a number of times to set
Top panel
AUTO
2
SET
2
1
1
SOURCE
DIMMER
CLOCK
ALARM TYPE
USB
the time until the system enters standby mode.
SOURCE + BEEP
BEEP
The sleep timer can be set to 30, 60, 90 and 120 minutes.
When the time is set, the sleep indicator ( ) is shown on the
front panel display.
y
LABEL SIDE
If you press SNOOZE/SLEEP while the sleep timer is activated, the
sleep timer setting will be canceled.
VOLUME
SOURCE
ALARM
SNOOZE SLEEP
PRESET
1
TONE CONTROL (REMOTE CONTROL ONLY)
1 Press one of the LOW/MID/HIGH EQ buttons on
Remote control
the remote control while playing back.
Select the tone to be adjusted (LOW, MID, HIGH).
3
2
Tone
: HIGH
Tone
:MID
Setting
:LOW
2 Press
/
to adjust the tone.
Each tone can be adjusted from –5 to +5.
1
3 Press
to complete settings.
You can also press the EQ button that you pressed in Step 1
to complete the settings.
To change the tone of other frequency band, return to step 1
and press the EQ button to adjust the desired tone.
ADJUSTING BRIGHTNESS OF FRONT PANEL DISPLAY
1 Adjust the brightness with the DIMMER switch on
Rear panel
the rear panel.
AUTO:
2
1 AUTO
1:
2:
adjusts the brightness automatically to match the
surroundings.
brighter.
darker.
Note
When AUTO is set, the brightness of the front panel display is adjusted
automatically with the illumination sensor (☞ P. 3). Ensure that the
sensor is not covered.
21 En
TROUBLESHOOTING
If there is a problem with the unit, check the following list first. If you cannot resolve the problem with the suggested solutions or if the
problem is not listed below, set the system to standby mode, unplug it, and consult the nearest authorized Yamaha dealer or service center.
General
Problem
Cannot turn on the unit.
The speakers make no sound.
Cause
Solution
The power cable is not connected firmly.
Reconnect the power cable into the wall outlet and
the unit firmly.
The unit may have received a strong electrical
shock such as lightning or excessive static
electricity.
Disconnect the power cable. Wait about 30 seconds,
reconnect the power cable, and turn on the system.
The volume may be set to the minimum level.
Adjust the volume level.
The source may be incorrect.
Select the correct source.
Auto Standby is activated.
Turn on the system again.
The sleep function (☞ P. 21) may be set.
Turn on the system and play the source again.
Auto Standby is activated.
Turn on the system again.
Sound is cracked/distorted or there is
abnormal noise.
Input source volume is excessive, or volume of this
unit is excessive (especially Bass).
Adjust volume with VOLUME, or adjust Bass with
EQ (☞ P. 21).
The unit does not operate properly.
The unit may have received a strong electrical
shock such as lightning or excessive static
electricity, or power supply may have dropped.
Set the system to standby mode and disconnect the
power cable. Wait about 30 seconds, reconnect the
power cable, and turn the system on.
A digital or high-frequency equipment
produces noises.
The unit may be placed too close to the digital or
high-frequency equipment.
Place the unit further away from the equipment.
The clock setting has been cleared.
The unit is left more than one week after you
disconnect the power cable from the wall outlet.
Plug the power cable into the wall outlet firmly, and
set the clock again (☞ P. 5).
The selected source does not play back at
the alarm time.
No CD or USB device is inserted.
Insert a CD or USB device.
ALARM TYPE switch is set to BEEP.
Set ALARM TYPE to SOURCE + BEEP or
SOURCE (☞ P. 18).
Clock flashes and the unit cannot be
operated.
CLOCK switch on the rear panel is set to SET, and
this unit is in clock setting mode.
Set CLOCK switch to CLOCK1 or CLOCK2
(☞ P. 5).
Auto Standby is inactive.
The unit may have picked up ambient noise.
If the unit is close to portable phones, wireless
devices, microwave ovens, fluorescent light, place
the unit further away from them.
The front display becomes dim.
The front display setting is set to AUTO.
Set the brightness of the front panel display to a
setting other than AUTO. Or, do not cover the
illumination sensor.
Sound suddenly turns off.
The system turns on but immediately
enters standby mode.
CD playback
Problem
Disc cannot be inserted.
Cause
Solution
The system is set to Eco Standby mode.
Press
to cancel Eco Standby mode. (☞ P. 2).
A disc is already inserted.
Press
to eject the disc.
Some button operations do not work.
The disc loaded into the unit may not be
compatible.
Use a disc supported by the unit (☞ P. 25).
Playback does not start after pressing
/ (playback stops immediately).
The disc may be dirty.
Wipe the disc clean.
The disc loaded into the unit may not be
compatible.
Use a disc supported by the unit (☞ P. 25).
If the unit was moved from a cold to warm place,
condensation may have formed on the disc reading
lens.
Wait for an hour or two until the unit adjusts to the
room temperature, and try again.
The disc loaded into the unit may not be
compatible.
Use a disc supported by the unit (☞ P. 25).
The CD indicator flashes twice, and
repeated 3 times, and the disc is ejected.
“Err” is displayed in the front panel
display after loading a disc.
22 En
The disc may be dirty.
Wipe the disc clean.
The disc does not contain playable files.
Use a disc contains playable files (☞ P. 25, 26).
The disc is loaded back to front.
Insert a disc facing the label side to near side.
An error occurs in the unit.
Eject the disc with
.
TROUBLESHOOTING
USB device playback
Problem
MP3/WMA file on the USB device does
not play.
Cause
The USB device is not recognized.
Solution
Set the system to standby mode and disconnect the
USB device. Then, turn the system on and
reconnect the USB device.
Connect an AC adapter if supplied with the device.
If the solutions above do not resolve the problem,
the USB device is not playable on the unit.
The USB indicator flashes twice, and
repeated 3 times, after connecting a USB
device.
“Err” is displayed in the front panel
display after connecting a USB device.
An incompatible USB device is connected to the
unit.
Set the system to standby mode and reconnect the
USB device to the unit. If it does not resolve the
problem, the USB device is not playable on the
unit.
The USB device does not contain playable files.
Use a USB device contains playable files
(☞ P. 25, 26).
An incompatible USB device is connected to the
unit.
Set the system to standby mode and reconnect the
USB device to the unit. If it does not resolve the
problem, the USB device is not playable on the
unit.
An overcurrent is detected.
Bluetooth
Problem
Cannot make this unit paired with the
connecting device.
Cannot establish a Bluetooth connection.
No sound is produced or the sound is
interrupted during playback.
Cause
Solution
The unit is already connected with another device.
Disconnect the already connected Bluetooth
device.
The connecting device does not support A2DP.
Perform pairing operations with a device which
supports A2DP.
A Bluetooth adaptor, etc. that you want to pair with
this unit has a password other than “0000”.
Use a Bluetooth adaptor, etc. whose password is
“0000”.
This unit and the connecting device are too far
apart.
Move the connecting device closer to this unit.
There is a device (microwave oven, wireless LAN,
etc.) outputs signals in the 2.4 GHz frequency band
nearby.
Move this unit away from the device that is
emitting radio-frequency signals.
This unit is not registered on the connecting
device’s Bluetooth connection list.
Perform pairing operations again (☞ P. 10).
Another Bluetooth device is already connected.
Terminate the current Bluetooth connection.
The Bluetooth function of the device is turned off.
Turn on the Bluetooth function of the device.
The pairing information has been deleted.
Perform pairing again (☞ P. 10).
This unit can be paired with up to eight connecting
devices. When pairing with the ninth device has
succeeded, pairing data for the device with the
oldest connection date will be deleted.
On iPhone, iPad, or iPod touch, delete the pairing
history with this unit and perform pairing again.
The Bluetooth connection of this unit with the
connecting device is disconnected.
Perform Bluetooth connection operations again
(☞ P. 12).
This unit and the connecting device are too far
apart.
Move the connecting device closer to this unit.
There is a device (microwave oven, wireless LAN,
etc.) outputs signals in the 2.4 GHz frequency band
nearby.
Move this unit away from the device that is
emitting radio-frequency signals.
The connecting device’s Bluetooth function is off.
Turn on the Bluetooth function of the connecting
device.
The connecting device is not set to send Bluetooth
audio signals to this unit.
Check that the Bluetooth function of the
connecting device is set properly.
The pairing setting of the connecting device is not
set to this unit.
Set the pairing setting of the connecting device to
this unit.
The connecting device’s volume is too low.
Increase the volume level.
23 En
TROUBLESHOOTING
DAB reception (ISX-803D only)
Problem
Cannot tune into any DAB stations.
Cause
Solution
The initial scan operations were not performed.
Perform the initial scan operations (☞ P. 13).
There is no DAB coverage in your area.
Check with your dealer or WorldDMB Online at
“http://www.worlddab.org” for a listing of the DAB
coverage in your area.
The DAB signals are too weak.
Change the height, direction, or placement of the
antenna.
The initial scan operations are not
successful and “Not found” appears on
the DAB information display.
The DAB signals are too weak.
There is no DAB coverage in your area.
Check with your dealer or WorldDMB Online at
“http://www.worlddab.org” for a listing of the DAB
coverage in your area.
The DAB station reception is weak.
The DAB signals are too weak.
There is noise interference (e.g. hiss,
crackle, or jitter).
The antenna needs to be repositioned.
Change the height, direction, or placement of the
antenna.
The DAB station information does not
appear or is inaccurate.
The DAB station may be temporarily out of
service, or the DAB station information is not
provided by the DAB broadcaster.
The DAB signals are too weak.
Contact the DAB broadcaster.
FM radio reception
Problem
Cause
Solution
Too much noise.
The antenna may be connected improperly.
Make sure the antenna is connected properly
(☞ P. 3) or use a commercially available outdoor
antenna.
Too much noise during stereo broadcast.
The radio station you selected may be far from your
area, or the radio wave reception is weak in your
area.
Try manual tuning to improve the signal quality
(☞ P. 15) or use a commercially available outdoor
antenna.
Even with an outdoor antenna, radio wave Multipath reflection or other radio interferences
may have occurred.
reception is weak. (Sound is distorted.)
Change the height, direction, or placement of the
antenna.
Remote control
Problem
The remote control does not work
properly.
24 En
Cause
Solution
The remote control may be operated outside its
operation range.
For information on the remote control operation
range, refer to “How to use the remote control”
(☞ P. 1).
The remote control signal receiver on the unit
(☞ P. 3) may be exposed to direct sunlight or
lighting (inverted fluorescent lamps).
Change the lighting or orientation of the unit.
The battery may be worn out.
Replace the batteries with two new ones.
There are obstacles between the remote control
signal receiver on the unit and the remote control.
Remove the obstacles.
NOTES ON DISCS AND USB DEVICES
CD information
USB device information
This unit is designed for use with audio CD, CD-R*, and CD-RW*
with the logos followings.
This unit supports USB mass storage class devices (e.g., flash
memories or portable audio players) using FAT16 or FAT32
format.
Notes
• Some devices may not work properly even if they meet the requirements.
• Do not connect devices other than USB mass storage class devices (such as
USB chargers or USB hubs), PCs, card readers, an external HDD, etc.
• Yamaha will not be held responsible for any damage to or data loss on the
USB device occurring while the device is connected to this unit.
• Playability of and power supply to all kind of USB devices are not
guaranteed.
• USB devices with encryption cannot be used.
* ISO 9660 format CD-R/RW
y
This unit can play back discs bearing any of the logo marks above. A disc
logo mark is printed on the disc and the disc jacket.
Notes
• Do not load any other type of disc into this unit. Doing so may damage this
unit.
• CD-R/RW cannot be played back unless finalized.
• Some discs cannot be played back depending on the disc characteristics or
recording conditions.
• Do not use any non-standard shaped discs such as a heart-shaped disc.
• Do not use discs with many scratches on their surface.
• Do not load a cracked, warped, or glued disc.
• Do not use 8-cm discs.
About MP3 or WMA files
Notes
• The unit can play back:
File
Bitrate (kbps)
Sampling
frequency (kHz)
MP3
8 - 320**
16 - 48
WMA
16 - 320**
22.05 - 48
** Both constant and variable bitrates are supported.
• The maximum numbers of files/folders that can be played on the unit are
as follows.
Handling a disc
• Do not touch the surface of the disc.
Hold a disc by its edge (and the center
hole).
• Do not use a pencil or pointed marker
to write on the disc.
Data CD
USB
Maximum total number of file
512
9999
Maximum folder number
255
128
Maximum file number per folder
511
255
• Copyright-protected files cannot be played back.
• Do not put a tape, seal, glue, etc., on a disc.
• Do not use a protective cover to prevent scratches.
• Do not load more than one disc into this unit at one time. This
can cause damage to both this unit and the discs.
• Do not insert any foreign objects into the disc slot.
• Do not expose a disc to direct
sunlight, high temperature, high
humidity, or a lot of dust.
Caution
• If a disc becomes dirty, wipe it with
a clean, dry cloth from the center
out to the edge. Do not use record
cleaner or paint thinner.
• To avoid malfunction, do not use a
commercially available lens
cleaner.
25 En
SPECIFICATIONS
‹ PLAYER
CD
• Media ...................................................................................CD, CD-R/RW
• Audio format .........................................................Audio CD, MP3, WMA
Laser
• Type .................................................... Semiconductor laser GaAs/GaAlAs
• Wave length ..................................................................................... 790 nm
• Output power...................................................................................... 7 mW
USB
• Audio format ........................................................................... MP3, WMA
‹ TUNER
• Tuning range
FM ...........................................................................87.50 to 108.00 MHz
DAB/DAB+ (ISX-803D only)........................174 to 240 MHz (Band III)
‹ GENERAL
•
•
•
•
•
Power supply..................................................... AC 100 to 240 V, 50/60 Hz
Power consumption.............................................................................. 11 W
Standby consumption (clock display on, Bluetooth Ready)............... 2.5 W
Eco Standby consumption (clock display off).................................... 0.4 W
Dimensions
410 mm
(16-1/8 in)
AUX
• Input connector ................................... 3.5 mm (1/8 in) STEREO mini jack
‹ Bluetooth
•
•
•
•
•
Bluetooth version ..................................................................Ver. 2.1 +EDR
Supported protocols ........................................................................... A2DP
Supported codecs ........................................................... SBC, AAC, aptX®
Wireless output ................................................................ Bluetooth Class 2
Maximum communication distance ................10 m (without obstructions)
410 mm
(16-1/8 in)
997 mm
(39-1/4 in)
‹ NFC (Near Field Communication)
587 mm
(23-1/8 in)
• Supported model......................NFC-ready Android device Ver. 4.1 or later
* Some models may not work or be different in the required distance for
connection.
Weight: 12.0 kg
(26.5 lbs.)
Φ 295 mm
(11-5/8 in)
Specifications are subject to change without notice.
iPad, iPhone, and iPod touch are trademarks of Apple Inc.,
registered in the U.S.and other countries.
Android and Google Play are trademarks of Google, Inc.
© 2013 CSR plc and its group companies.
The aptX® mark and the aptX logo are trade marks of CSR plc or
one of its group companies and may be registered in one or more
jurisdictions.
(For ISX-803D)
This unit supports DAB/DAB+ tuning.
26 En
SPECIFICATIONS
Bluetooth
• Bluetooth is a technology for wireless communication between
devices within an area of about 10 meters (33 ft) employing the
2.4 GHz frequency band, a band which can be used without a
license.
• Bluetooth is a registered trademark of the Bluetooth SIG and is
used by Yamaha in accordance with a license agreement.
Handling Bluetooth communications
• The 2.4 GHz band used by Bluetooth compatible devices is a
radio band shared by many types of equipment. While Bluetooth
compatible devices use a technology minimizing the influence of
other components using the same radio band, such influence may
reduce the speed or distance of communications and in some
cases interrupt communications.
• The speed of signal transfer and the distance at which
communication is possible differs according to the distance
between the communicating devices, the presence of obstacles,
radio wave conditions and the type of equipment.
• Yamaha does not guarantee all wireless connections between this
unit and devices compatible with Bluetooth function.
Information for Users on Collection and Disposal
of Old Equipment and Used Batteries
These symbols on the products, packaging, and/or
accompanying documents mean that used electrical and
electronic products and batteries should not be mixed
with general household waste.
For proper treatment, recovery and recycling of old
products and used batteries, please take them to
applicable collection points, in accordance with your
national legislation and the Directives 2002/96/EC and
2006/66/EC.
By disposing of these products and batteries correctly,
you will help to save valuable resources and prevent any
potential negative effects on human health and the
environment which could otherwise arise from
inappropriate waste handling.
For more information about collection and recycling of
old products and batteries, please contact your local
municipality, your waste disposal service or the point of
sale where you purchased the items.
LASER SAFETY
This unit employs a laser. Due to possible eye injury, only a
qualified service person should remove the cover or attempt to
service this device.
[Information on Disposal in other Countries
outside the European Union]
These symbols are only valid in the European Union. If
you wish to discard these items, please contact your
local authorities or dealer and ask for the correct method
of disposal.
DANGER
This unit emits visible laser radiation when open. Avoid direct eye
exposure to beam. When this unit is plugged into the wall outlet,
do not look inside the unit through the disc slot and other openings.
Note for the battery symbol (bottom two
symbol examples):
This symbol might be used in combination with a chemical
symbol. In this case it complies with the requirement set
by the Directive for the chemical involved.
The laser component in this product is capable of emitting
radiation exceeding the limit for Class 1.
◆ For U.K. customers
If the socket outlets in the home are not suitable for the plug supplied
with this appliance, it should be cut off and an appropriate 3 pin plug
fitted. For details, refer to the instructions described below.
Note
The plug severed from the mains lead must be destroyed, as a plug with
bared flexible cord is hazardous if engaged in a live socket outlet.
◆ Special Instructions for U.K. Model
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured RED.
Make sure that neither core is connected to the earth terminal of
the three pin plug.
If there should be color blotching or noise when used near a TV,
move this unit away from the TV when using it.
Do not use this unit within 22 cm (9 inches) of persons with a
heart pacemaker implant or defibrillator implant.
Radio waves may affect electro-medical devices.
Do not use this unit near medical devices or inside medical
facilities.
The user shall not reverse engineer, decompile, alter, translate
or disassemble the software used in this unit, whether in part or
in whole. For corporate users, employees of the corporation
itself as well as its business partners shall observe the
contractual bans stipulated within this clause. If the stipulations
of this clause and this contract cannot be observed, the user
shall immediately discontinue using the software.
We, Yamaha Music Europe GmbH hereby declare that this unit
is in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
Yamaha Music Europe GmbH
Siemensstr. 22-34 25462 Rellingen, Germany
Tel: +49-4101-303-0
27 En
The name plate is located on the rear panel of the unit.
28 En
© 2014 Yamaha Corporation
Printed in China ZN80010
Download PDF

advertising