Poulan Pro | PPB1000E | Instruction manual | Poulan Pro PPB1000E Instruction manual

ENGLISH
R
Please do not return product to retailer.
Por favor, no devuelva el producto al lugar de compra.
Veuillez ne pas retourner le produit au détaillant.
1--800--554--6723
Register your product online at:
Registre su producto en línea en:
Enregistrez votre produit en ligne à l’adresse :
www.poulanpro.com
PPB335
ESPAÑOL
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
For Occasional Use Only
Poulan PRO
7349 Statesville Road
Charlotte, NC 28269
Poulan PRO
850 Matheson Blvd. West
Mississauga, Ontario L5V 0B4
115248826 Rev. 4 4/22/10 BRW
FRANÇAIS
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones graves.
AVERTISSEMENT:
Lire le manuel d’instructions et bien respecter tous les avertissements et toutes les instructions de sécurité. Tout défaut de le
faire pourrait entraîner des blessures graves.
TABLE OF CONTENTS
Identification of Safety Symbols
Safety Rules
Assembly
Operation
Maintenance
2
4
9
10
13
Service & Adjustments
Storage
Troubleshooting Table
Limited Warranty Statement
Emissions Statement
14
15
16
17
17
IDENTIFICATION OF SAFETY SYMBOLS
DANGER: Use only specified trimmer
head, spool, and recommended trimmer line.
Never use blades, flailing devices, wire, rope,
string, etc. This attachment is designed for line
trimmer use only. Failure to follow these instructions may result in serious injury.
WARNING: This unit can be dangerous! Careless or improper
use can cause serious injury.
WARNING: Read the operator’s manual before use. Failure to
follow instructions could result in serious injury to the operator and/or
bystanders. Save operator’s manual.
Trimmer line can throw objects violently.
You can be blinded or injured. Always
wear hearing protection and safety
glasses marked Z87. Always wear head
protection, heavy, long pants, long
sleeves, boots and gloves.
Hazard zone for thrown objects.
S Trimmer line throws objects violently.
S You and others can be blinded/injured.
S Keep children, bystanders, and animals 50 feet
(15 meters) away.
Secure hair above shoulder length. Do
not wear jewelry, loose clothing, or
clothing with loosely hanging straps,
ties, tassels, etc. They can be caught in
moving parts.
2
IDENTIFICATION OF SAFETY SYMBOLS
Assist handle to be positioned only below
the arrow.
Never allow children to operate this unit.
Store unit indoors in a high, dry place out of the reach of
children.
When servicing unit, use only identical replacement
parts.
Always stop unit and disconnect spark plug before cleaning or servicing.
WARNING: Fire hazard. Never mix, pour, or store gasoline or
use the unit near a flame or sparks (including smoking, open flames, or
work that can cause sparks).
Use unleaded gasoline and two--stroke oil mixed at a ratio of
40:1 (2.5%).
3
OPTIONAL ATTACHMENTS
These attachments used in combination with the specified powerhead have been evaluated
to ANSI B175.3--2003, “Grass Trimmers and Brushcutters -- Safety Requirements”. These
combinations have been evaluated by Underwriter’s Laboratories Inc. (UL) and are consequently UL listed:
Powerhead model Attachments
Type
Trimmer head
PPB335
WE fixed line
Brushcutter attachment PPB4000C
Cutting attachment / guard,
part. no.
545053902 / 545003325
952711828
These attachments used in combination with the specified powerhead have been evaluated
to applicable ISO-- and EN safety requirement standards by the Swedish Machinery Testing
Institute:
Attachments
Type
Part. no.
Edger attachment
PPB1000E
952711825
Cultivator attachment
PPB2000T
952711826
Blower attachment
PPB3000B
952711827
Pruner attachment
PPB5000P
952711906
Pruner attachment
PPB5500P
952711671
SAFETY RULES
S Always wear face or dust mask if operation is
dusty.
S Always wear heavy, long pants, long sleeves,
boots, and gloves. Wearing safety leg guards
is recommended.
S Always wear foot protection. Do not go
barefoot or wear sandals. Stay clear of
spinning line.
S Secure hair above shoulder length. Secure or
remove loose clothing or clothing with loosely
hanging ties, straps, tassels, etc. They can be
caught in moving parts.
S Being fully covered also helps protect you
from debris and pieces of toxic plants thrown
by spinning line.
S Stay Alert. Do not operate this unit when you
are tired, ill, upset or under the influence of
alcohol, drugs, or medication. Watch what
you are doing; use common sense.
S Wear hearing protection.
S Never start or run inside a closed room or
building. Breathing exhaust fumes can
kill.Keep handles free of oil and fuel.
S Keep handles free of oil and fuel.
S Always keep engine on the right hand side
of your body.
S Hold the unit firmly with both hands.Keep
trimmer head (or other optional attachment)
below waist level and away from all parts of
your body. Do not raise engine above your
waist.
S Keep all parts of your body away from muffler
and spinning line (or other optional
attachment). Keep engine below waist level.
A hot muffler can cause serious burns.
S Keep firm footing and balance. Do not
overreach or use from unstable surfaces
such as ladders, trees, steep slopes,
rooftops, etc.
WARNING: When using gardening
appliances, basic safety precautions must always be followed to reduce the risk of fire and
serious injury. Read and follow all instructions.
This power unit can be dangerous! Operator
is responsible for following instructions and
warnings on unit and in manual. Read entire
instruction manual before using unit! Be thoroughly familiar with the controls and the proper use of the unit. Restrict the use of this unit
to persons who have read, understand, and
will follow the instructions and warnings on
the unit and in the manual. Never allow children to operate this unit.
INSTRUCTION
MANUAL
SAFETY INFORMATION
ON THE UNIT
DANGER: Never use blades with line
trimmer attachment. Never use flailing devices
with any attachment. This unit (when used with
supplied line trimmer attachment) is designed
for line trimmer use only. Use of any other accessories or attachments with line trimmer attachment will increase the risk of injury.
If situations occur which are not covered in
this manual, use care and good judgment. If
you need assistance, contact your authorized
service dealer or call 1-800-554--6723.
OPERATOR SAFETY
S Dress properly. Always wear safety glasses
or similar eye protection when operating, or
performing maintenance, on your unit (safety
glasses are available). Eye protection should
be marked Z87.
4
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or abnormal swellings. Prolonged use in cold weather
has been linked to blood vessel damage in
otherwise healthy people. If symptoms occur
such as numbness, pain, loss of strength,
change in skin color or texture, or loss of feeling
in the fingers, hands, or joints, discontinue the
use of this tool and seek medical attention. An
anti--vibration system does not guarantee the
avoidance of these problems. Users who operate power tools on a continual and regular basis
must monitor closely their physical condition
and the condition of this tool.
SPECIAL NOTICE: This unit is equipped
with a temperature limiting muffler and spark arresting screen which meets the requirements of
California Codes 4442 and 4443. All U.S. forest
land and the states of California, Idaho, Maine,
Minnesota, New Jersey, Oregon, and Washington require by law that many internal combustion engines be equipped with a spark arresting
screen. If you operate in a locale where such
regulations exist, you are legally responsible for
maintaining the operating condition of these
parts. Failure to do so is a violation of the law.
For normal homeowner use, the muffler and
spark arresting screen will not require any service. After 50 hours of use, we recommend that
your muffler be serviced or replaced by your authorized service dealer.
S Use only in daylight or good artificial light.
S Use only for jobs explained in this manual
(or manuals for optional attachments).
UNIT / MAINTENANCE SAFETY
S Disconnect the spark plug before performing
maintenance except carburetor adjustments.
S Look for and replace damaged or loose parts
before each use. Look for and repair fuel
leaks before use. Keep in good working
condition.
S Replace trimmer head parts that are chipped,
cracked, broken, or damaged in any other
way before using the unit.
S Maintain unit according to recommended
procedures. Keep cutting line at proper
length.
S Use only 0.115 inch (3 mm) diameter
Poulan PRO brand line. Never use wire,
rope, string, etc.
S Install required shield properly before using
the unit. Use only specified trimmer head;
make sure it is properly installed and securely
fastened.
S Make sure unit is assembled correctly as
shown in this manual.
S Make carburetor adjustments with lower end
supported to prevent line from contacting any
object.
S Keep others away when making carburetor
adjustments.
S Use only recommended Poulan PRO
accessories and replacement parts.
S Have all maintenance and service not
explained in this manual performed by an
authorized service dealer.
LINE TRIMMER SAFETY
FUEL SAFETY
S
S
S
S
S
S
S
S
WARNING: Inspect the area before
each use. Remove objects (rocks, broken
glass, nails, wire, etc.) which can be thrown
by or become entangled in line. Hard objects
can damage the trimmer head and be thrown
causing serious injury.
S Keep others including children, animals,
bystanders, and helpers at least 50 feet (15
meters) away. Bystanders should be
encouraged to wear safety glasses. Stop
engine immediately if you are approached.
S Use only for trimming, scalping, mowing
and sweeping. Do not use for edging,
pruning or hedge trimming.
S Cut from your left to your right. Cutting on
right side of the shield will throw debris
away from the operator.
Mix and pour fuel outdoors.
Keep away from sparks or flames.
Use a container approved for fuel.
Do not smoke or allow smoking near fuel or
the unit.
Avoid spilling fuel or oil. Wipe up all fuel spills.
Move at least 10 feet (3 meters) away from
fueling site before starting engine.
Stop engine and allow to cool before
removing fuel cap.
Always store gasoline in a container
approved for flammable liquids.
TRANSPORTING AND STORAGE
S Allow engine to cool; secure unit before
storing or transporting in vehicle.
S Empty the fuel tank before storing or
transporting the unit. Use up fuel left in the
carburetor by starting the engine and letting it
run until it stops.
S Store unit and fuel in area where fuel vapors
cannot reach sparks or open flames from
water heaters, electric motors or switches,
furnaces, etc.
S Store unit so line limiter blade cannot
accidentally cause injury. The unit can be
hung by the shaft.
S Store unit out of reach of children.
ADDITIONAL SAFETY RULES
FOR OPTIONAL ATTACHMENTS
WARNING: For each optional attachment used, read entire instruction manual before use and follow all warnings and instructions in manual and on attachment.
WARNING: Ensure handlebar is
installed when using brushcutter attachments. Attach handlebar above arrow on
safety label on the upper shaft (engine end of
unit). If your brushcutter attachment does not
include a handlebar, a handlebar accessory
kit (#530071451) is available from your authorized service dealer.
WARNING: The engine exhaust
from this product contains chemicals known
to the State of California to cause cancer, birth
defects or other reproductive harm.
5
S Never run unit without the proper
equipment attached. When using your unit
as a blower, always install blower tubes.
S Check air intake opening, blower tubes or
vacuum tubes frequently, always with
engine
stopped
and
spark
plug
disconnected. Keep vents and discharge
tubes free of debris which can accumulate
and restrict proper air flow.
S Never place any object in air intake opening
as this could restrict proper air flow and cause
damage to the unit.
S Never use for spreading chemicals, fertilizers,
or other substances which may contain toxic
materials.
S To avoid spreading fire, do not use near leaf or
brush fires, fireplaces, barbecue pits,
ashtrays, etc.
Handlebar
EDGER SAFETY
WARNING: Inspect the area to be
edged before each use. Remove objects
(rocks, broken glass, nails, wire, etc.) which
can be thrown by the blade or can wrap
around the shaft.
BRUSHCUTTER SAFETY
WARNING: Blade rotates momentarily after the trigger is released or engine is
turned off. The blade can seriously cut you or
others. Allow blade to stop before removing it
from the cut.
DANGER: Blade can thrust violently
away from material it does not cut. Blade
thrust can cause amputation of arms or legs.
WARNING: Do not use trimmer head
as a fastening device for the blade.
S Throw away blades that are bent, warped,
cracked, broken or damaged in any other
way. Replace parts that are cracked,
chipped, or damaged before using the unit.
S Do not attempt to remove cut material nor
hold material to be cut when the engine is
running or when cutting blade is moving.
S Always keep the wheel and depth adjusting
skid in contact with the ground.
S Always push the unit slowly over the
ground. Stay alert for uneven sidewalks,
holes in the terrain, large roots, etc.
WARNING: The blade continues to
spin after the trigger is released or engine is
turned off. The coasting blade can throw objects or seriously cut you if accidentally
touched. Stop the blade by contacting the left
hand side of the coasting blade with material
already cut.
BLOWER/VACUUM SAFETY
WARNING: Inspect area before
starting unit. Remove all debris and hard objects such as rocks, glass, wire, etc. that can
ricochet, be thrown, or otherwise cause injury
or damage during operation.
S Do not set unit on any surface except a clean,
hard area while engine is running. Debris
such as gravel, sand, dust, grass, etc., could
be picked up by the air intake and thrown out
through discharge opening, damaging unit,
property, or causing serious injury to
bystanders or operator.
S Never place objects inside the blower tubes,
vacuum tubes or blower outlet. Always direct
the blowing debris away from people,
animals, glass, and solid objects such as
trees, automobiles, walls, etc. The force of air
can cause rocks, dirt, or sticks to be thrown or
to ricochet which can hurt people or animals,
break glass, or cause other damage.
6
WARNING: Inspect the area to be
cut before each use. Remove objects (rocks,
broken glass, nails, wire, etc.) which can be
thrown or become entangled in the blade or
trimmer line.
HEDGE TRIMMER SAFETY
S Throw away and replace blades that are
bent, warped, cracked, broken or damaged
in any other way.
S Install required shield properly before using
the unit. Use the metal shield for all metal
blade use. Only use brushcutter
attachments that provide a metal shield
with proboscis nose.
DANGER: RISK OF CUT; KEEP
HANDS AWAY FROM BLADE -- Blade moves
momentarily after the trigger is released or engine is turned off. Do not attempt to clear away
cut material when the blade is in motion. Make
sure the switch is in the OFF position, the spark
plug wire is disconnected, and the blade has
stopped moving before removing jammed material from the cutting blade. Do not grab or hold
the unit by the cutting blade.
Proboscis
nose
S Use only specified blade and make sure it is
properly installed and securely fastened.
S Cut from your right to your left.
S Always use the handlebar and a properly
adjusted shoulder strap with blade (see
ASSEMBLY instructions in brushcutter
attachment instruction manual).
CULTIVATOR SAFETY
WARNING: Rotating tines can cause
serious injury. Keep away from rotating tines.
Stop the engine and disconnect the spark plug
before unclogging tines or making repairs.
WARNING: Inspect the area before
starting the unit. Remove all debris and hard
objects such as rocks, glass, wire, etc. that
can ricochet, be thrown, or otherwise cause
injury or damage during operation.
S Do not use a cutting blade that is bent,
warped, cracked, broken or damaged in any
other way. Have worn or damaged parts
replaced by an authorized service dealer.
S Always keep unit in front of your body.
Keep all parts of your body away from the
cutting blade.
S Keep the cutting blade and air vents clear of
debris.
WARNING: Inspect the area to be
cultivated before starting the unit. Remove all
debris and hard and sharp objects such as
rocks, vines, branches, rope, string, etc.
S Avoid heavy contact with solid objects that
might stop the tines. If heavy contact occurs,
stop the engine and inspect the unit for
damage.
S Never operate the cultivator without the tine
cover in place and properly secured.
S Keep the tines and guard clear of debris.
S After striking a foreign object, stop the
engine, disconnect the spark plug and
inspect the cultivator for damage. Repair
before restarting.
S Disconnect attachment from the drive engine
before cleaning the tines with a hose and
water to remove any build--up. Oil the tines to
prevent rust.
S Always wear gloves when servicing or
cleaning the tines. The tines become very
sharp from use.
S Do not run unit at high speed unless
cultivating.
POLE PRUNER SAFETY
WARNING: The reciprocating blade/
rotating chain can cause severe injury. Inspect the unit before use. Do not operate unit
with a bent, cracked or dull blade or dull chain.
Keep away from the blade/chain.
WARNING: The reciprocating blade/
rotating chain is sharp. Do not touch. To prevent serious injury, always stop engine and
ensure blade/chain has stopped moving, disconnect spark plug, and wear gloves when
changing or handling the blade or chain.
WARNING: A coasting blade/rotating chain can cause injury while it continues to
move after the engine is stopped. Maintain
proper control of the unit until the blade/chain
has completely stopped moving. Keep
hands, face and feet at a distance from all
moving parts. Do not attempt to touch or stop
the blade or chain when it is moving.
7
WARNING: Falling objects can
cause severe head injury. Wear head protection when operating this unit with a pole pruner attachment.
WARNING: Never lean over discharge chute. Rocks or debris could be
thrown into the eyes and face and cause serious injury or blindness.
WARNING: Inspect the area where
the unit is to be used. Remove objects that
could be thrown or damage the unit. Some
objects may be hidden by fallen snow -- be
alert for the possibility.
S Direct material discharge away from glass
enclosures, automobiles, etc.
S Do not run engine at high speed while not
removing snow.
S Be attentive when using the snowthrower,
and stay alert for holes in the terrain and other
hidden hazards.
S Make sure the rotor will spin freely before
attaching the snowthrower to the powerhead.
S If the rotor will not rotate freely due to frozen
ice, thaw the unit before thoroughly before
attempting to operate under power.
S Keep the rotor clear of debris.
S Do not throw snow near other people. The
snow thrower could propel small objects at
high speed causing injury.
S After striking a foreign object, stop the
engine, disconnect spark plug and inspect
the snowthrower for damage and repair if
necessary before restarting unit.
S Never operate the snowthrower near glass
enclosures, automobiles and trucks.
S Never attempt to use the snowthrower on a
roof.
S Never operate the snowthrower near
window wells, dropoffs, etc.
S Never discharge snow onto public roads or
near moving traffic.
S Clear snow from slopes by going up and
down; never across. Use caution when
changing directions. Never clear snow from
steep slopes.
S Let snowthrower run for a few minutes after
clearing snow so moving parts do not
freeze.
S Look behind and use care when backing up.
Exercise caution to avoid slipping or falling,
especially when operating in reverse.
S Know how to stop quickly.
WARNING: To prevent serious injury,
do not use more than one boom extension with
a pole pruner attachment.
WARNING: Keep the pruner away
from power lines or electrical wires.
S Only use for pruning limbs or branches
overhead up to 4 inches (10 cm) in diameter.
S Do not operate the unit faster than the
speed needed to prune. Do not run the unit
at high speed when not pruning.
S Always stop the unit when work is delayed
or when walking from one cutting location to
another.
S If you strike or become entangled with a
foreign object, stop the engine immediately
and check for damage. Have any damage
repaired by an authorized service dealer
before attempting further operations.
Discard blades that are bent, warped,
cracked or broken.
S Stop the unit immediately if you feel excessive
vibration. Vibration is a sign of trouble. Inspect
thoroughly for loose nuts, bolts or damage
before continuing. Contact an authorized
service dealer for repair or replacement of
affected parts as necessary.
SNOW THROWER SAFETY
WARNING: Keep hands and feet
away from the rotor when starting or running
the engine. Never attempt to clear the rotor
with the engine/motor running. Stop engine
and disconnect spark plug before unclogging
snow or debris from discharge chute or when
adjusting vanes.
8
ASSEMBLY
WARNING: If received assembled,
repeat all steps to ensure your unit is properly
assembled and all fasteners are secure.
Examine parts for damage. Do not use damaged parts.
NOTE: If you need assistance or find parts
missing or damaged, call 1-800-554-6723.
It is normal for the fuel filter to rattle in the
empty fuel tank.
Finding fuel or oil residue on muffler is normal
due to carburetor adjustments and testing
done by the manufacturer.
Locking/Release
Button in Primary Hole
For assembly of optional attachments (see
list on page 11), refer to the ASSEMBLY section of the applicable attachment instruction
manual.
INSTALLING TRIMMER ATTACHMENT
CAUTION: When installing trimmer attach-
ment, place the unit on a flat surface for stability.
1. Loosen the coupler by turning the knob
counterclockwise.
ATTACHING THE SHIELD
WARNING: The shield must be properly installed. The shield provides partial protection from the risk of thrown objects to the operator and others and is equipped with a line limiter
blade which cuts excess line to the proper
length. The line limiter blade (on underside of
shield) is sharp and can cut you. For proper
orientation of shield, see KNOW YOUR TRIMMER illustration in OPERATION section.
1. Remove wing nut from shield.
2. Insert bracket into slot as shown.
3. Pivot shield until bolt passes through hole in
bracket.
Coupler
Shipping
protector
LOOSEN
Knob
TIGHTEN
Bracket
2. Remove shipping protector from coupler.
3. Remove the shaft cap from the trimmer attachment (if present).
4. Position locking/release button of attachment into guide recess of coupler.
5. Push the attachment into the coupler until
the locking/release button snaps into the
primary hole.
6. Before using the unit, tighten the knob securely by turning clockwise.
Shield
Slot
Coupler Primary Hole
Guide Recess
4. Reinstall wing nut and tighten securely.
Upper
Shaft
WingNut
Locking/
Release Attachment
Button
WARNING: Make sure the locking/
release button is locked in the primary hole
and the knob is securely tightened before operating the unit. All attachments are designed
to be used in the primary hole unless otherwise
stated in the applicable attachment instruction
manual. Using the wrong hole could lead to serious injury or damage to the unit.
9
ADJUSTING THE HANDLE
WARNING: When adjusting the handle, be sure it remains above the safety label
and below the mark or arrow on the shaft.
1.
2.
Loosen wing nut on handle.
Rotate the handle on the shaft to an upright position; retighten wing nut.
OPERATION
KNOW YOUR UNIT
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT.
Compare the illustrations with your unit to familiarize yourself with the location of the various controls
and adjustments. Save this manual for future reference.
Assist handle
Coupler
ON/STOP switch
Shaft
Trimmer head
Spark plug
Primer bulb
Shield
Muffler
Throttle trigger
Line limiter
blade
Choke lever
ON/STOP SWITCH
The ON/STOP switch is used to stop engine. To
stop the engine, push and release the engine
ON/STOP switch.
PRIMER BULB
The PRIMER BULB removes air from the carburetor and fuel lines and fills them with fuel.
This allows you to start the engine with fewer
pulls on the starter rope. Activate the primer
bulb by pressing it and allowing it to return to
its original form.
BEFORE STARTING ENGINE
WARNING: Be sure to read the fuel
information in the safety rules before you begin. If you do not understand the safety rules,
do not attempt to fuel your unit. Call
1-800-554-6723.
FUELING ENGINE
WARNING:
when refueling.
Remove fuel cap slowly
HELPFUL TIP
To obtain the correct oil mix
ratio, pour 3.2 ounces of
2-- cycle synthetic oil into
one gallon of fresh gas.
This engine is certified to operate on unleaded
gasoline. Before operation, gasoline must be
mixed with a good quality synthetic 2-cycle aircooled engine oil designed to be mixed at a ratio
Starter handle
CHOKE
The CHOKE helps to supply fuel to the engine
to aid in cold starting. Activate the choke by
moving the choke lever to the FULL CHOKE
position. After the engine attempts to start, move
the choke lever to the HALF CHOKE position.
Once engine has started, move the choke lever
to the RUN position.
COUPLER
The COUPLER enables optional attachments to be installed on the unit.
of 40:1. Poulan/WEED EATER brand synthetic
oil is recommended. Mix gasoline and oil at a ratio of 40:1. A 40:1 ratio is obtained by mixing 3.2
fluid ounces (95 ml) of oil with 1 gallon (4 liters)
of unleaded gasoline. DO NOT USE automotive
oil or marine oil. These oils will cause engine
damage. When mixing fuel, follow instructions
printed on container. Once oil is added to gasoline, shake container momentarily to assure that
the fuel is thoroughly mixed. Always read and
follow the safety rules relating to fuel before fueling your unit.
CAUTION: Never use straight gasoline in
your unit. This will cause permanent engine
damage and void the limited warranty.
FUEL REQUIREMENTS
This engine requires the use of minimum 87
octane [R+M]/2 clean gasoline.
IMPORTANT
Use of alcohol blended fuels (called gasohol or
using ethanol or methanol) can cause major engine performance and durability problems.
10
WARNING:
Alternative fuels (not gasoline) such as E--15 (15% alcohol), E--20 (20%
alcohol), E--85 (85% alcohol) are NOT classified
as gasoline and are NOT approved for use in
2--stroke gasoline engines. Use of alternative
fuels will cause problems such as: improper
clutch engagements, overheating, vapor lock,
power loss, lubrication deficiency, deterioration
of fuel lines, gaskets and internal carburetor
components, etc. Alternative fuels cause high
moisture absorption into the fuel/oil mixture
leading to oil and fuel separation.
4.
5.
6.
HOW TO STOP YOUR UNIT
S Release the throttle trigger.
S Push and release the engine ON/STOP
switch. The switch will automatically return
to the ON position. Wait 5 seconds before
attempting to restart unit to allow switch to
reset.
ON/STOP switch
7.
Pull starter rope handle sharply until engine
sounds as if it is trying to start, but do not
pull rope more than 6 times.
As soon as engine sounds as if it is trying to
start, move choke lever to HALF CHOKE
position.
Pull starter rope sharply until engine runs,
but no more than 6 pulls. NOTE: If the engine doesn’t start after 6 pulls (at the HALF
CHOKE position), move the choke lever to
the FULL CHOKE position and press the
primer bulb 6 times. Pull the starter rope 2
more times. Move the choke lever to the
HALF CHOKE position and pull the starter
rope until the engine runs, but no more than
6 pulls. If the engine still doesn’t start, it is
probably flooded. Proceed to STARTING A
FLOODED ENGINE.
Once the engine starts, allow it to run 10
seconds. Squeeze throttle trigger and allow
the unit to run for 30 more seconds at RUN.
Release throttle trigger. NOTE: If engine
dies with the choke lever in the RUN position, move the choke lever to FULL
CHOKE then back to HALF CHOKE and
pull the rope until engine runs, but no
more than 6 pulls.
STARTING A WARM ENGINE
HOW TO START YOUR UNIT
1.
WARNING: Avoid any contact with
the muffler. A hot muffler can cause serious
burns.
Starting position
HELPFUL TIP
If your engine still does not
start after following these
instructions, please call
1-- 800-- 554-- 6723.
STARTING A COLD ENGINE
NOTE: DO NOT squeeze the throttle trigger
until the engine has started and runs.
1. Set unit on a flat surface.
2. Slowly press the primer bulb 6 times.
3. Move choke lever to the FULL CHOKE
position.
Primer bulb
Move choke lever to the FULL CHOKE
position, then to the HALF CHOKE position to set fast idle.
2. Pull starter rope sharply until engine runs,
but no more than 6 pulls.
3. Allow engine to run 15 seconds, then move
the choke lever to RUN.
NOTE: If engine has not started, pull starter
rope 5 more pulls. If engine still does not run, it
is probably flooded.
STARTING A FLOODED ENGINE
Flooded engines can be started by placing the
choke lever in the RUN position; then, pull the
rope to clear the engine of excess fuel. This
could require pulling the starter handle many
times depending on how badly the unit is
flooded. If the unit still doesn’t start, refer to
TROUBLESHOOTING TABLE or call
1-800-554-6723.
OPERATING THE COUPLER
This model is equipped with a coupler which
enables optional attachments to be installed.
The optional attachments are:
MODEL:
Edger . . . . . . . . . . . . . . . . . . . . . PPB1000E
Cultivator . . . . . . . . . . . . . . . . . . PPB2000T
Blower . . . . . . . . . . . . . . . . . . . . PPB3000B
Brushcutter . . . . . . . . . . . . . . . . PPB4000C
Pruner . . . . . . . . . . . . . . . . . . . . PPB5000P
Pruner . . . . . . . . . . . . . . . . . . . . PPB5500P
WARNING: Always stop unit and disconnect spark plug before removing or installing attachments.
Choke lever
Muffler
Starter handle
REMOVING TRIMMER ATTACHMENT (OR OTHER OPTIONAL
ATTACHMENTS)
CAUTION: When removing or installing at-
tachments, place the unit on a flat surface for
stability.
11
1. Loosen the coupler by turning the knob
counterclockwise.
Coupler
OPERATING INSTRUCTIONS
It is recommended that the engine not be
operated for longer than 1 minute at full
throttle.
OPERATING POSITION
Attachment
LOOSEN
ALWAYS WEAR:
Hearing
protection
Eye protection
Knob
TIGHTEN
2. Press and hold the locking/release button.
Locking/Release
Button
Long pants
Heavy shoes
Upper Shaft
Coupler
3. While securely holding the engine and
upper shaft, pull the attachment straight
out of the coupler.
Attachment
INSTALLING OPTIONAL ATTACHMENTS
1. Remove the shaft cap from the attachment (if present).
2. Position locking/release button of attachment into guide recess of coupler.
3. Push the attachment into the coupler until
the locking/release button snaps into the
primary hole.
4. Before using the unit, tighten the knob securely by turning clockwise.
Coupler Primary Hole
Guide Recess
Upper
Shaft
Locking/
Release Attachment
Button
WARNING: Make sure the locking/
release button is locked in the primary hole
and the knob is securely tightened before operating the unit. All attachments are designed
to be used in the primary hole unless otherwise
stated in the applicable attachment instruction
manual. Using the wrong hole could lead to serious injury or damage to the unit.
Cut only from your left to your right.
WARNING: Always wear eye protection. Never lean over the trimmer head.
Rocks or debris can ricochet or be thrown into
eyes and face and cause blindness or other
serious injury.
When operating unit, stand as shown and
check for the following:
S Wear eye protection and heavy clothing.
S Hold trigger handle with your right hand and
assit handle with left hand.
S Keep unit below waist level.
S Cut only from your left to your right to
ensure debris is thrown away from you.
Without bending over, keep line near and
parallel to the ground and not crowded into
material being cut.
Do not run the engine at a higher speed than
necessary. The cutting line will cut efficiently
when the engine is run at less than full throttle.
At lower speeds, there is less engine noise and
vibration. The cutting line will last longer and will
be less likely to “weld” onto the spool. Always
release the throttle trigger and allow the engine to return to idle speed when not cutting.
To stop engine:
S Release the throttle trigger.
S Push and release the engine ON/STOP
switch.
CUTTING METHODS
Locking/Release
Button in Primary Hole
WARNING: Use minimum speed
and do not crowd the line when cutting around
hard objects (rock, gravel, fence posts, etc.),
which can damage the trimmer head, become
entangled in the line, or be thrown causing a
serious hazard.
S The tip of the line does the cutting. You will
achieve the best performance and minimum line wear by not crowding the line into
the cutting area. The right and wrong ways
are shown below.
12
Tip of the line
does the cutting.
Line crowded into
work area.
Right
Wrong
Scalping
S The line will easily remove grass and
weeds from around walls, fences, trees and
flower beds, but it also can cut the tender
bark of trees or shrubs and scar fences.
S For trimming or scalping, use less than full
throttle to increase line life and decrease
head wear, especially:
S During light duty cutting.
S Near objects around which the line can wrap
such as small posts, trees or fence wire.
S For mowing or sweeping, use full throttle for
a good clean job.
TRIMMING -- Hold the bottom of the trimmer
head about 3 inches (8 cm) above the ground
and at an angle. Allow only the tip of the line to
make contact. Do not force trimmer line into
work area.
MOWING -- Your trimmer is ideal for mowing
in places conventional lawn mowers cannot
reach. In the mowing position, keep the line
parallel to the ground. Avoid pressing the
head into the ground as this can scalp the
ground and damage the tool.
Trimming
SWEEPING -- The fanning action of the rotating line can be used to blow away loose debris
from an area. Keep the line parallel to and
above the area surface and swing the tool
from side to side.
Mowing
Sweeping
3 inches (8 cm)
above ground
SCALPING -- The scalping technique removes
unwanted vegetation down to the ground. Hold
the bottom of the trimmer head about 3 in. (8
cm) above the ground and at an angle. Allow the
tip of the line to strike the ground around trees,
posts, monuments, etc. This technique increases line wear.
MAINTENANCE
WARNING:
Disconnect the spark
plug before performing maintenance except
for carburetor adjustments.
HELPFUL TIP
IMPORTANT: Have all
repairs other than the recommended maintenance
described in the instruction
manual performed by an
authorized service dealer.
If any dealer other than an authorized
service dealer performs work on the
product, Poulan PRO may not pay for
repairs under warranty. It is your responsibility to maintain and perform
general maintenance.
CHECK FOR LOOSE
FASTENERS AND PARTS
S
S
S
S
S
Spark Plug Boot
Air Filter
Housing Screws
Assist Handle Screw
Debris Shield
CHECK FOR DAMAGED OR
WORN PARTS
Contact an authorized service dealer for replacement of damaged or worn parts.
S ON/STOP Switch -- Ensure ON/STOP
switch functions properly by pushing and
releasing the switch. Make sure engine
stops. Wait 5 seconds before attempting to
restart unit to allow switch to reset. Restart
engine and continue.
13
S Fuel Tank -- Discontinue use of unit if fuel
tank shows signs of damage or leaks.
S Debris Shield -- Discontinue use of unit if
debris shield is damaged.
INSPECT AND CLEAN UNIT AND
DECALS
S After each use, inspect complete unit for
loose or damaged parts. Clean the unit and
decals using a damp cloth with a mild detergent.
S Wipe off unit with a clean dry cloth.
CLEAN AIR FILTER
A dirty air filter decreases engine performance and increases fuel consumption and
harmful emissions. Always clean after every
5 hours of operation.
1. Clean the cover and the area around it to
keep dirt from falling into the carburetor
chamber when the cover is removed.
2. Loosen bolt with a 5/16 inch (8 mm) socket
wrench. Remove air filter cover and air filter.
NOTE: To avoid creating a fire hazard or
producing harmful evaporative emissions, do
not clean filter in gasoline or other flammable
solvent.
3. Wash the filter in soap and water.
4. Allow filter to dry.
5. Replace parts.
Air filter
Air filter cover
INSPECT MUFFLER AND SPARK
ARRESTING SCREEN
WARNING: The muffler on this product contains chemicals known to the State of
California to cause cancer.
As your unit is used, carbon deposits build up
on the muffler and spark arresting screen and
must be removed to avoid creating a fire hazard or affecting engine performance.
For normal homeowner use, the muffler and
spark arresting screen will not require any
service. After 50 hours of use, we recommend that your muffler be serviced or replaced by an authorized service dealer.
REPLACE SPARK PLUG
Replace the spark plug each year to ensure
the engine starts easier and runs better. Inspect spark plug every 25 hours of usage.
Clean and/or replace as necessary. Set spark
plug gap at 0.025 inch (0.6 mm). Ignition timing is fixed and nonadjustable.
NOTE: This spark ignition system complies
with the Canadian standard ICES--002.
1. Twist, then pull off spark plug boot.
2. Remove spark plug from cylinder and
discard.
3. Replace with Champion RCJ-6Y spark
plug and tighten securely with a 3/4 inch
(19 mm) socket wrench.
4. Reinstall the spark plug boot.
Bolt
SERVICE AND ADJUSTMENTS
REPLACING THE LINE
For unit to operate properly, the cutting line
should be replaced when line becomes worn to
less than 3 inches (7.5 cm) in length from the
edge of the line exit tunnels on each side of the
cutting head.
1. Remove and discard worn line before
installing new line.
2. Use only 0.115 inch (3 mm) diameter
Poulan PRO brand cut length line.
3. Insert one end of the line through the
positioning tunnel.
4. Continue to feed line through tunnel until
line is centered (leaving equal amounts
on each side). See illustration below.
Positioning
tunnel
5.
Insert ends of line one at a time through
the line exit tunnels.
6. Pull the line and make sure the line is extended fully through the tunnels.
Line exit
Line exit
tunnel
tunnel
7.
Correctly installed line will be the same
length on both ends.
REPLACING THE CUTTING HEAD
1.
2.
14
Align hole in the dust cup with the hole in
the side of the gearbox by rotating the
dust cup.
Insert a small screwdriver into aligned
holes. This will keep the shaft from turning
while removing and installing trimmer head.
To adjust idle speed:
Allow engine to idle. Adjust speed until engine
runs without trimmer head, blade or optional
attachment moving or spinning (idle too fast)
or stalling (idle speed too slow).
S Turn idle speed screw clockwise to increase
engine speed if engine stalls or dies.
S Turn idle speed screw counterclockwise to
decrease engine speed if trimmer head,
blade or optional attachment moves or
spins at idle.
Screwdriver
3. While holding the screwdriver in position,
remove trimmer head by turning clockwise (looking from bottom of unit).
4. Thread replacement trimmer head onto
the shaft by turning counterclockwise.
Tighten until secure.
5. Remove the screwdriver.
WARNING: Recheck the idle speed
after each adjustment. The trimmer head,
blade or optional attachment must not move
or spin at idle speed to avoid serious injury to
the operator or others.
Idle Speed Screw
CARBURETOR IDLE SPEED
ADJUSTMENT
WARNING: Keep others away when
making idle speed adjustments. The trimmer
head, blade or any optional attachment will be
spinning during most of this procedure. Wear
your protective equipment and observe all safety precautions. After making adjustments, the
trimmer head, blade or any optional attachment
must not move/spin at idle speed.
The carburetor has been carefully set at the
factory. Adjustments may be necessary if you
notice any of the following conditions:
S Engine will not idle when the throttle is
released.
S The trimmer head, blade or optional
attachment moves/spins at idle.
Make adjustments with the unit supported so
the cutting attachment is off the ground and
will not make contact with any object. Hold
the unit by hand while running and making adjustments. Keep all parts of your body away
from the cutting attachment and muffler.
Air Filter
Cover
If you require further assistance or are unsure
about performing this procedure, contact an
authorized
service
dealer
or
call
1--800--554--6723.
STORAGE
WARNING:
Perform the following
steps after each use:
S Allow engine to cool before storing or transporting.
S Store unit and fuel in a well ventilated area
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
S Store unit with all guards in place. Position
unit so that any sharp object cannot accidentally cause injury.
S Store unit and fuel well out of the reach of
children.
FUEL SYSTEM
Under FUELING ENGINE in the OPERATION section of this manual, see message labeled IMPORTANT regarding the use of gasohol in your engine.
Fuel stabilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits
during storage. Add stabilizer to the gasoline
in the fuel tank or fuel storage container.
Follow the mix instructions found on stabilizer
container. Run engine at least 5 minutes after
adding stabilizer.
HELPFUL TIP
SEASONAL STORAGE
Prepare unit for storage at end of season or if
it will not be used for 30 days or more.
If your unit is to be stored for a period of time:
S Clean the entire unit before lengthy storage.
S Store in a clean dry area.
S Lightly oil external metal surfaces.
During storage of your gas/
oil mixture, the oil will separate from the gas.
We recommend that you
shake the gas can weekly
to insure proper blending of
the gas and oil.
15
ENGINE
S Remove spark plug and pour 1 teaspoon of
40:1, 2-cycle engine oil (air cooled) through
the spark plug opening. Slowly pull the
starter rope 8 to 10 times to distribute oil.
S Replace spark plug with new one of recommended type and heat range.
S Clean air filter.
S Check entire unit for loose screws, nuts,
and bolts. Replace any damaged, broken,
or worn parts.
S At the beginning of the next season, use
only fresh fuel having the proper gasoline to
oil ratio.
OTHER
S Do not store gasoline from one season to
another. Replace your gasoline can if it
starts to rust.
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect spark plug before performing all of the
recommended remedies below except remedies that require operation of the unit.
TROUBLE
CAUSE
REMEDY
Engine will not
start.
1. Engine flooded.
1. See “Starting a Flooded Engine” in
Operation Section.
2. Fill tank with correct fuel mixture.
3. Install new spark plug.
4. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
5. Contact an authorized service dealer.
2. Fuel tank empty.
3. Spark plug not firing.
4. Fuel not reaching
carburetor.
5. Carburetor requires
adjustment.
Engine will
not idle
properly.
Engine will not
accelerate,
lacks power,
or dies under
a load.
Engine
smokes
excessively.
Engine runs
hot.
1. Carburetor requires
adjustment.
2. Crankshaft seals worn.
3. Compression low.
1. Air filter dirty.
2. Spark plug fouled.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
5. Compression low.
1. Fuel mixture incorrect.
2. Air filter dirty.
3. Carburetor requires
adjustment.
1. Fuel mixture incorrect.
2. Spark plug incorrect.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
1. See “Carburetor Idle Speed Adjustment”
in Service and Adjustments Section.
2. Contact an authorized service dealer.
3. Contact an authorized service dealer.
1. Clean or replace air filter.
2. Clean or replace plug
and regap.
3. Contact an authorized service dealer.
4. Contact an authorized service dealer.
5. Contact an authorized service dealer.
1. Empty fuel tank and refill with
correct fuel mixture.
2. Clean or replace air filter.
3. Contact an authorized service dealer.
1. See “Fueling Engine” in Operation
section.
2. Replace with correct spark plug.
3. Contact an authorized service dealer.
4. Contact an authorized service dealer.
16
LIMITED WARRANTY
Poulan PRO, a division of Husqvarna
Consumer Outdoor Products N.A., Inc., warrants to the original consumer purchaser that
each new Poulan PRO brand gasoline tool or
attachment is free from defects in material and
workmanship and agrees to repair or replace
under this warranty any defective gasoline product or attachment as follows from the original
date of purchase.
2 YEARS - Parts and Labor, when used for
household purposes.
90 DAYS - Parts and Labor, when used for
commercial, professional, or income producing
purposes.
30 DAYS - Parts and Labor, if used for rental
purposes.
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance or alteration, or
the use of accessories and/or attachments not
specifically recommended by Poulan PRO for
this tool. This warranty does not cover tune--up,
spark plugs, filters, starter ropes, cutting line, or
rotating head parts that will wear and require replacement with reasonable use during the warranty period. This warranty does not cover pre-delivery setup or normal adjustments explained
in the instruction manual. This warranty does
not cover transportation costs.
In the event you have a claim under this warranty, you must return the product to an authorized
service dealer.
Should you have any unanswered questions
concerning this warranty, please contact:
Poulan PRO, a division of Husqvarna
Consumer Outdoor Products N.A., Inc.
7349 Statesville Road
Charlotte, NC 28269
1--800--554--6723
In Canada, contact:
Poulan PRO
850 Matheson Blvd. West
Mississauga, Ontario L5V 0B4
Giving the model number, serial number and
date of purchase of your product and the name
and address of the authorized dealer from
whom it was purchased.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE OTHER RIGHTS WHICH VARY FROM STATE TO
STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EXPRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY
TO YOU.
This is a limited warranty within the meaning of
that term as defined in the Magnuson--Moss Act
of 1975.
The policy of Poulan PRO is to continuously
improve its products. Therefore, Poulan
PRO reserves the right to change, modify, or
discontinue models, designs, specifications,
and accessories of all products at any time
without notice or obligation to any purchaser.
U.S. EPA / CALIFORNIA / ENVIRONMENT CANADA
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGATIONS: The U.S. Environmental
Protection Agency, California Air Resources
Board, Environment Canada and Poulan
PRO are pleased to explain the emissions control system warranty on your year 2010 and later small off--road engine. In California, all small
off--road engines must be designed, built, and
equipped to meet the State’s stringent anti-smog standards. Poulan PRO must warrant
the emission control system on your small
off--road engine for the periods of time listed
below provided there has been no abuse, neglect, or improper maintenance of your small
off--road engine. Your emission control system
includes parts such as the carburetor, the ignition system and the fuel tank. Where a warrantable condition exists, Poulan PRO will repair
your small off--road engine at no cost to you.
Expenses covered under warranty include
diagnosis, parts and labor.
MANUFACTURER’S WARRANTY COVERAGE: If any emissions related part on your
engine (as listed under Emissions Control
Warranty Parts List) is defective or a defect in
the materials or workmanship of the engine
causes the failure of such an emission related
part, the part will be repaired or replaced by
Poulan PRO. OWNER’S WARRANTY RESPONSIBILITIES: As the small off--road engine owner, you are responsible for the performance of the required maintenance listed
in your instruction manual. Poulan PRO recommends that you retain all receipts covering
maintenance on your small off--road engine,
but Poulan PRO cannot deny warranty solely
for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. As the small off--road engine owner,
you should be aware that Poulan PRO may
deny you warranty coverage if your small off-road engine or a part of it has failed due to
17
abuse, neglect, improper maintenance, unapproved modifications, or the use of parts
not made or approved by the original equipment manufacturer. You are responsible for
presenting your small off--road engine to an
Poulan PRO authorized repair center as soon
as a problem exists. Warranty repairs should be
completed in a reasonable amount of time, not
to exceed 30 days. If you have any questions
regarding your warranty rights and responsibilities, you should contact your nearest authorized service center, call Poulan PRO at
1--800--554--6723, or send e-mail corresponemission.warranty@HCOP-dence
to
emission.com. WARRANTY COMMENCEMENT DATE: The warranty period begins on
the date the small off--road engine is purchased. LENGTH OF COVERAGE: This
warranty shall be for a period of two years
from the initial date of purchase, or until the
end of the product warranty (whichever is longer). WHAT IS COVERED: REPAIR OR REPLACEMENT OF PARTS. Repair or replacement of any warranted part will be
performed at no charge to the owner at an approved Poulan PRO servicing center. If you
have any questions regarding your warranty
rights and responsibilities, you should contact
your nearest authorized service center, call
Poulan PRO at 1--800--554--6723, or send
e-mail correspondence to emission.warranty
@HCOP--emission.com. WARRANTY PERIOD: Any warranted part which is not
scheduled for replacement as required maintenance, or which is scheduled only for regular inspection to the effect of “repair or replace
as necessary” shall be warranted for 2 years.
Any warranted part which is scheduled for replacement as required maintenance shall be
warranted for the period of time up to the first
scheduled replacement point for that part.
DIAGNOSIS: The owner shall not be
charged for diagnostic labor which leads to
the determination that a warranted part is defective if the diagnostic work is performed at
an approved Poulan PRO servicing center.
CONSEQUENTIAL DAMAGES: Poulan
PRO may be liable for damages to other engine components caused by the failure of a
warranted part still under warranty. WHAT IS
NOT COVERED: All failures caused by
abuse, neglect, or improper maintenance are
not covered. ADD-- ON OR MODIFIED
PARTS: The use of add--on or modified parts
can be grounds for disallowing a warranty
claim. Poulan PRO is not liable to cover failures
of warranted parts caused by the use of add--on
or modified parts. HOW TO FILE A CLAIM: If
you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized service center, call
Poulan PRO at 1--800--554--6723, or send
e-mail correspondence to emission.warranty
@HCOP--emission.com. WHERE TO GET
WARRANTY SERVICE: Warranty services
or repairs shall be provided at all Poulan PRO
service centers. Call: 1--800--554--6723 or
send e-mail correspondence to emission.
warranty@HCOP--emission.com. MAINTENANCE, REPLACEMENT AND REPAIR
OF EMISSION RELATED PARTS: Any Poulan PRO approved replacement part used in
the performance of any warranty maintenance or repair on emission related parts will
be provided without charge to the owner if the
part is under warranty. EMISSION CONTROL WARRANTY PARTS LIST: Carburetor, air filter (covered up to maintenance
schedule), ignition system: spark plug (covered up to maintenance schedule), ignition
module, muffler including catalyst (if
equipped), fuel tank. MAINTENANCE
STATEMENT: The owner is responsible for
the performance of all required maintenance
as defined in the instruction manual.
The information on the product label indicates which standard your engine is certified.
Example: (Year) EPA and/or CALIFORNIA.
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
18
Download PDF