Autostart AS-1755V Installation guide

5 - B U T T O N M A N U A L / A U T O M A T I C
T R A N S M I S S I O N R E M O T E S T A R T E R
W I T H V I R T U A L T A C H S Y S T E M
( A S P R G - 1 0 0 0 C O M P A T I B L E )
QUICK INSTALLATION GUIDE
To obtain a copy of the installation guide, please visit our website at www.autostart.ca
TableofContents
Manual or Automatic Transmission setup
1
Multi-speed Tach Programming
Push-To-Start
2
Transponder Programming
NEW FEATURE – PTS takeover
2
Resetting the Module
NEW FEATURE – Hybrid Option
2
Bypass
Entering Programming Mode
2
NEW FEATURE – SmartStart™
Programming the transmitter to the module
3
Testing
Entering Programming Options
3
Troubleshooting
Programming Options
4
Diagnostics – Parking Light Flash Table
Horn adjustment
5
Diagnostic table for start failure.
Setting up the TACH
6
Diagnostic table for shutdown.
Virtual Tach adjustment
6
The wiring diagram is at the middle of this guide.
6
6
6
6
7
7
9
9
9
9
MANUAL OR AUTOMATIC TRANSMISSION SETUP
This module may be installed on vehicles with manual or automatic transmissions. It is originally configured for
manual transmissions. If the vehicle you are working on is automatic, it is mandatory to make a few quick and
easy modifications before the unit is connected. In the event that the configuration requires changes afterwards,
a complete reset will be necessary before those changes become effective.
To install this unit in a vehicle with a MANUAL transmission:
1.
Make sure the Yellow loop on the PC board is connected.
2.
Connect the Orange handbrake wire located on the 12-pin harness to the vehicle handbrake
circuit.
3.
Connect the Blue/White (+) door input OR the Grey (-) door input wire located on the 12-pin
harness to the vehicle door pin wire, which monitors all the doors of the vehicle (only use 1 of the 2
door trigger inputs).Make sure the Purple TACH wire is plugged in – the TACH wire MUST be
hooked up when the module is set for a manual transmission.
4.
Make all your regular connections.
5.
Power up the unit by first inserting the 5-pin connector, then the 6-pin connector and finally the 12pin connector. The parking lights will flash 4 times.
6.
When learning the transmitter, the parking lights will flash 5 times quickly.
7.
Upon the first successful remote start, the system will lock the transmission settings to manual
mode.
To install this unit in a vehicle with an AUTOMATIC transmission:
1.
Cut the loop on the pc board (Yellow wire).
2.
Make sure the Orange handbrake wire is not connected to any of the vehicle circuits.
3.
Make all the regular connections.
4.
Power up the unit. The parking lights will flash 4 times.
5.
When learning the first transmitter, the parking lights will flash 5 times quickly then give 2 slow
flashes.
6.
Upon the first successful remote start (once the yellow loop has been cut), the system will lock the
transmission settings to automatic mode.
Notice
The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product, be
that either damage to the vehicle itself or to the unit. This unit must be installed by a certified technician using all safety devices
supplied. Please note that this guide has been written for properly trained Autostart technicians: a certain level of skills and
knowledge is therefore assumed. Please review the installation guide carefully before beginning any work.
Warning
Before installing the unit, if installing on a vehicle with a manual transmission, test that the OEM Door Switch contacts of the
vehicle work well, and that the Parking Brake system operates properly. If installing on a vehicle with an automatic
transmission, test that the vehicle does not start when the gearshift lever is in the “Drive” position. If it starts in gear, reset the
remote starter to manual transmission.
Doc#: 110705
Rev.:3.8
© 2011
- 1W-AM-5B-A/M-HD -
- FcN -
Canada
Note: If upon pressing the START button the parking lights give 3 slow flashes, make sure that the Orange
handbrake wire is not connected, the hand brake is not engaged and that the yellow loop is cut and
isolated/taped.
DIESEL VEHICLE WARNING: The G-Plug wire must not be connected when the brake is detected through
D2D.
Problem: D2D brake could not be detected.
Cause: The unit is locked in wire to wire brake communication mode.
Solution: Reset the power. If unsuccessful, perform a factory reset.
DIAGNOSTICS – PARKING LIGHT FLASH TABLE
PUSH-TO-START
Disabled by default, PTS mode is a special feature that is intended to facilitate the remote starter installation on
most Push-To-Start vehicles. With PTS mode enabled, the remote starter will offer the installer a negative start
output (to pulse the vehicle’s PTS switch), as well as a (+) brake switch output (no external relay necessary).
With PTS enabled, the White/Green wire on the 12-pin harness becomes your negative (-) PTS switch output. It
will give a one second output intended to pulse the PTS switch. Also, the Purple crank output becomes your
brake switch output (this will turn the brake circuit ON for crank).
NEW FEATURE – PTS takeover
Without the PTS takeover, pressing the brake pedal after remote starting shuts down the engine (to prevent
theft). Here are the new steps for this new Takeover mode:
Regular PTS takeover from Remote start:
1.
Remote start the engine.
2.
3.
TROUBLESHOOTING
and enter the vehicle.
Press
Within the time limit (1.5 min or 3 min), press the brake pedal.
Diagnostic table for shutdown.
Parking lights flashes
1
PTS takeover from Idle mode:
1.
2.
With the engine running, press
,
or to engage Idle mode.
Exit the vehicle; engine runs without the key.
3.
IMPORTANT: After exiting the vehicle, press
4.
5.
Press
and enter the vehicle.
Within the time limit (1.5 min or 3 min), press the brake pedal.
Diagnostic table for start failure.
Parking lights flashes
1
(Manual transmission only)
1 slow Î 2 quick
1 slow Î 2 quick Î 2 quick
3
(Automatic transmission only)
4
5
(Manual transmission only)
6
10
2
. (Note: No door detection.)
3
4
10
Flash for 30 sec.
Flash for 60 sec.
NEW FEATURE – HYBRID OPTION
Warning: For automatic transmissions only.
This option is disabled by default. It can be enabled in Mode 4 of the programming options.
HYBRID mode is a special feature that is intended to facilitate the remote starter installation on most Hybrid
vehicles. With HYBRID mode enabled, the remote starter will give a four second crank output on its crank wire
(It will not rely on VTS to stop the crank cycle). The only way to shorten the four second crank output is to
program a tach signal to the remote starter. If a tach signal is programmed, the remote starter will act like
normal (the HYBRID feature should be used when a tach reference is not available from the vehicle or the
bypass being used at the time of installation).
x
Cause
Ready mode is not activated.
x
x
x
x
x
x
The system is set to valet mode.
The system is in Home valet
The parking brake is active.
Yellow loop is connected.
Brake wire is active.
Tach signal is not learned.
x
x
A tach signal is detected before Ignition.
Hood wire is active.
x
x
x
x
x
x
x
x
Cause
Runtime has expired.
Shutdown by remote.
Ready mode is activated.
Failed start (VTS or tach failure, depending on selected).
Brake shutdown.
Hood shutdown.
Panic mode.
Alarm triggered.
Note: The installer can also use the PRG-1000 to diagnose shutdown and remote start failures.
Refer to the PRG-1000 manual guide.
ENTERING PROGRAMMING MODE
These are the programming buttons:
The Hood Pin
The Antenna Programming Button (the A.P.B.)
*
*
The Programming Button
(a.k.a. the P.B.)
P.2
http://www.autostart.ca
Quick Installation Guide
Quick installation Guide
http://www.autostart.ca
P.9
‰ Hood switch shutdown. With the vehicle running under the remote car starter, open the hood; the
vehicle should shut down. If it does not shut down, check the hood pin-switch and its connector.
‰ Brake shutdown circuit. With the vehicle running under the remote car starter, press and release the
brake pedal. The engine should shut down immediately. If it continues to run, check the brake switch
connection.
The P.B. is located on the side of the module. This push button mimics the hood-pin switch in order to avoid
having to get out of the vehicle and pressing the hood-pin switch. The P.B. will work only when the hood pin
is installed and the hood is up.
Complete step by step module programming
1)
2)
3)
4)
5)
6)
‰ Parking brake shutdown circuit (manual transmissions only). With the vehicle running under
remote start, disengage the parking brake. The engine should shut down immediately. If the engine
continues to run, check the parking brake switch connection.
‰ OEM alarm control. Make sure the module is able to arm and disarm the OEM alarm (if applicable).
‰ Door locks and trunk testing. Make sure each of these options respond to the transmitter (if
installed).
‰ Door pin shutdown circuit (manual transmissions only). Make sure the system exits ready mode
when each door is opened. (Test each door.)
‰ Starter kill option. Sit inside the vehicle with all doors closed. Arm the vehicle, then try to start the
engine with the key. The engine should not start. If the engine starts, rewire the starter kill to reach
proper operation.
‰ Valet mode. Make sure the remote car starter is able to properly enter and exit valet mode. When
setting the remote car starter into valet mode, pressing the lock button will lock the doors without
activating the starter kill. (Refer to the user guide for further information on valet mode.)
‰ Idle mode. Make sure the vehicle properly enters and exits idle mode.
‰ Door. Make sure that when the system is armed, opening any door or opening the trunk will trigger
the alarm (if installed).
‰ Hood trigger. Make sure that when the system is armed, opening the hood should trigger the alarm.
‰ Most comebacks are the result of misunderstandings about how a product works or performs.
Take the time to properly explain all functions and features to the customers before they leave
the premises. Doing this will save time and money.
Entering Programming Mode
Programming the transmitter to the module
Entering Programming Options
Programming the options
Adjusting the Horn output (if installed)
Setting up the TACH, VTS or Multi-speed Tach
Entering programming mode using the
Hood Pin
x Press and hold the hood pin down for 4 seconds.
x Release the hood pin.
The parking lights will turn ON.
Entering programming mode using the
A.P.B.
x Make sure the hood is closed.
x Turn the ignition key to the IGNITION ON (RUN)
position.
x While the parking lights are ON, press the hood pin
once more and release immediately.
The parking lights will turn ON and stay ON for
20 seconds leaving you time to select one of the
sub-menus.
x Within 5 seconds, press the programming button
on the antenna twice for 1 second each time.
The LED will come ON solid for 20 sec.
x You now have 20 seconds to select one of the
sub-menus.
Note 1: To exit programming mode, close the hood.
Note 1: To exit programming mode, press on the
antenna button once (the LED will come ON) and
release.
Note 2: For vehicles that require the ignition to be turned ON to activate the brake circuit, follow these steps:
x
After flashing the hood, turn the ignition ON and wait for the parking lights to come ON. Then,
press the brake pedal to access the sub-menus.
Warning!
Please note that the wire to wire brake communication is locked once an analog signal is detected on the
remote starter’s brake input. To detect D2D brake again, after being locked in “wire to wire” mode, make sure
no connection is made at the brake input wire and then reset the power.
PROGRAMMING THE TRANSMITTER TO THE MODULE
1.
2.
In programming mode (page 3) - the parking lights will stay on for up to 20 seconds.
Before the lights go out, turn the ignition key to OFF (if not OFF already), then ON, then OFF.
button and keep it down until the parking lights flash 5 times quickly (unit will
Press and hold the
click). The parking lights remain lit for 20 seconds.
4.
The transmitter has been stored in memory. Each unit can store 4 remotes in its memory.
5.
Either close the hood to end the programming procedure or select one of the sub-menus before the lights
turn off.
To program a transmitter on the second vehicle for multi-car operation;
3.
press the
button (instead of
) in step 3 of the transmitter programming procedure.
ENTERING PROGRAMMING OPTIONS
1. In programming mode (page 3)  the parking lights will stay on for up to 20 seconds.
2. Before the lights go out, press and hold the brake pedal and then press one of the following buttons.
x
x
LOCK to access mode 1;
UNLOCK to access mode 2;
x
x
TRUNK to access mode 3;
START to access mode 4.
3. The parking lights will flash 1, 2, 3 or 4 times to confirm entry into a mode.
4. Release the brake pedal.
P.8
http://www.autostart.ca
Quick Installation Guide
Quick installation Guide
http://www.autostart.ca
P.3
Once the desired mode has been selected, the unit will fall (by default) into function #1 of that mode; you can
now select the option you want in function 1. Once this option has been chosen, the unit will move on to
function 2 of the mode selected, and so on.
LOCK to access option 1;
UNLOCK to access option 2;
x
x
x
x
TRUNK to access option 3;
START to access option 4.
5. After the programming of any mode is completed, the parking lights and the LED on the antenna will turn
ON for 20 sec. During those 20 seconds, select one of the sub-menus if needed.
PROGRAMMING OPTIONS
* INDICATES DEFAULT SETTING
MODE 1
FUNCTION 1 – Ignition-controlled door locks
OPTION 1*
Ignition lock DISABLED
OPTION 2
Ignition lock ENABLED
OPTION 3
Ignition unlock only
OPTION 4
Ignition lock only
FUNCTION 2 – Secure Lock
OPTION 1*
Secure lock DISABLED
OPTION 2
Standard secure lock ENABLED
OPTION 3
Smart secure lock ENABLED
FUNCTION 3 – Starter Kill
OPTION 1*
Passive arming (60 sec.)
OPTION 2
Active arming
OPTION 3
Passive arming (3 min.)
FUNCTION 4 – Door lock / unlock pulse timing
OPTION 1*
7/10-sec. lock / unlock pulses
OPTION 2
4-sec. lock / unlock pulses
OPTION 3
7/10-sec. lock pulse and two ¼ -sec. unlock pulses
OPTION 4
1/10-sec. lock / unlock pulses
FUNCTION 5 – LED flashing
OPTION 1*
Enabled (will only flash when ignition is OFF)
OPTION 2
DISABLED
OPTION 3
ENABLED (will only flash when Starter kill engages (depends on Mode 1,
Function 3 programming)
* INDICATES DEFAULT SETTING
MODE 2
FUNCTION 1 – Safe Start
OPTION 1
Safe start ENABLED
OPTION 2*
Safe start DISABLED
OPTION 3
Swap Start
FUNCTION 2 – Engine Run Time
OPTION 1
Run time = 3 minutes in gas mode / 8 minutes diesel mode
OPTION 2*
Run time = 15 minutes in gas mode / 20 minutes diesel mode
OPTION 3
Run time = 25 minutes in gas mode / 30 minutes diesel mode
FUNCTION 3 –Idle Mode & Turbo Mode (auto) / Turbo Mode (manual)
OPTION 1
Idle mode & turbo mode DISABLED (AUTO) / turbo mode DISABLED (MANUAL)
OPTION 2*
Idle mode & turbo mode ENABLED (AUTO) / turbo mode DISABLED (MANUAL)
OPTION 3
Idle mode & turbo mode ENABLED (AUTO) / turbo mode ENABLED (MANUAL)
FUNCTION 4 – Engine type and Cold Weather Mode
OPTION 1
Diesel mode with 20-minute run time in cold weather mode (30-sec. wait to start delay)
OPTION 2*
Gas mode with 3-minute run time in cold weather mode
OPTION 3
Diesel mode with 8-minute run time in cold weather mode (18-sec. wait to start delay)
OPTION 4
Diesel mode with 8-minute run time in cold weather mode (7-sec. wait to start delay)
FUNCTION 5 – Disarm option
OPTION 1
Disarm with Ignition, Accessory and Ground Out
OPTION 2*
Disarm only
NEW FEATURE – SMARTSTART™
When teamed up with a SmartStart™-compatible module, remote start features can be accessed using a
smartphone. These features include lock/unlock, engine start/stop, trunk release, panic and alarm notifications.
For alarm notifications, the Xpresskit™ bypass option (D2D) must be enabled.
To use these features, connect the SmartStart™ module to the SmartStart™ port located at the back of the
remote start module (see the wiring diagram). The SmartStart™ feature must be enabled using the
programming options list found in this guide.
TESTING
Before putting the vehicle back together, it is recommended to check that the system operates properly. The
following testing procedures should be used to verify proper installation and operation of the system. Before
testing, make sure that all connections are soldered and that the unit is plugged in.
‰
Make sure the system properly enters and exits ready mode:
Ready mode is a sequence of steps that must be followed in order to allow manual transmission
vehicles to be remote started. To get into ready mode:
If Ready Mode is enabled by remote
If Ready Mode is enabled by handbrake
1. Ensure that all the doors, hood and trunk are closed. Make sure that the gear selector is in the neutral
position.
2. With the engine already running, apply the parking 2. With the engine already running, apply the parking
brake once and release the brake pedal.
brake twice within 10 sec.
3. Within 20 sec. of engaging the parking brake, 3. Make sure to release the brake pedal.
The parking lights will flash 3 times quickly and
press and hold
,
or
on the transmitter
remain lit.
(SmartStart™ uses only ).
The parking lights will flash 3 times quickly and
remain lit.
4. Remove the key: the engine will keep on running.
5. Exit the vehicle. All doors should be closed, including the hood and trunk.
OPTION 1: No lock
NOW THERE ARE THREE POSSIBLE OPTIONS
OPTION 2: Manual shut down
OPTION 3: Automatic shut
down
(default)
The engine stops.
The engine keeps going until you
press either;
x
to lock the doors and shut
down the engine;
x
to unlock the doors and shut
down the engine;
The engine runs for 8 sec. then
locks the doors before finally
shutting down the engine, without
user interaction.
x
WARNING: The vehicle is not
armed or locked down.
to shut down the engine
without affecting the doors.
WARNING: Engine runs until the preprogrammed run time expires.
WARNING: Do not leave your
keys in the vehicle!
6. The Parking lights will flash.
The system will exit ready mode if a door, the hood or the trunk is opened, if the brake pedal is pressed, if the parking brake is disengaged or if the ignition key is turned to the IGNITION ON (RUN)
position.
‰ Remote-start the engine and listen for starter drag. If the starter cranks for too long, carry out
another tach programming procedure.
P.4
http://www.autostart.ca
Quick Installation Guide
Quick installation Guide
http://www.autostart.ca
P.7
SETTING UP THE TACH
* INDICATES DEFAULT SETTING
MODE 3
FUNCTION 1 – Home Valet
OPTION 1
Home valet ENABLED
OPTION 2*
Home valet DISABLED
FUNCTION 2 – AUX 1 Programming
OPTION 1
Horn confirmation upon the 2nd press of the LOCK button
OPTION 2*
Priority door access
OPTION 3
Horn confirmation upon the 1st press of the LOCK button
OPTION 4
Negative Accessory output
FUNCTION 3 – AUX 2 Programming
OPTION 1
Constant output
OPTION 2*
Toggle ON/OFF (with 30-second time out)
OPTION 3
Toggle ON/OFF (with 4-minute time out) Æ active when started remotely
OPTION 4
Negative Starter output
FUNCTION 4 – AUX 3 / TRUNK output
OPTION 1
1-sec. output
OPTION 2*
Constant output
OPTION 3
Trunk output with disarm and rearm pulses
FUNCTION 5 – External Trigger
OPTION 1
Zone 3 with disarm/rearm (trunk monitor)
OPTION 2*
Key sense
OPTION 3
Engine start/stop
OPTION 4
SmartStart™
VIRTUAL TACH ADJUSTMENT
Warning: For automatic transmissions only.
Virtual Tach System combines the latest microcontroller technology and a complex algorithm that took years to
develop. VTS is able to effectively monitor the engine starting sequence and release the starter at the right time
without physically connecting the tach wire to the remote starter. The VTS constantly monitors the data and
readjusts itself automatically in order to maximize its capability to start the engine properly in any weather or
deteriorating battery condition.
OPTIONAL TIME DELAY ADJUSTMENT IN VIRTUAL TACH SYSTEM
Follow these steps to program crank time adjustment, if needed:
1. In programming mode (page 3).
Before the lights go out, press and hold the brake pedal and press the LOCK and UNLOCK buttons
simultaneously  the parking lights will flash 4 times. Do not release the brake pedal.
2. Press the LOCK button if you wish to increase the time delay or the UNLOCK button if you want to
decrease it. The time delay will be increased or decreased by 50 ms and the parking lights will flash
once every time the LOCK or UNLOCK button is pressed.
3. Press the TRUNK button to save the settings you have entered.
4. Release the brake pedal – the time delay programming is now complete.
MULTI-SPEED TACH PROGRAMMING
* INDICATES DEFAULT SETTING
MODE 4
FUNCTION 1 – Alarm control
OPTION 1
ENABLED (HORN must be enabled in MODE 3 FUNCTION 2, option 1 or 3)
OPTION 2
DISABLED
FUNCTION 2 – Ready Mode Option / Hybrid Option
OPTION 1
ENABLED by handbrake
OPTION 2*
ENABLED by remote
OPTION 3
Hybrid option ENABLED
FUNCTION 3 – Ready mode completion option
OPTION 1
Open/Close door
OPTION 2*
Remote
OPTION 3
Open/Close door with automatic door-lock
FUNCTION 4 – Bypass
OPTION 1
ADS (1-way D2D)
OPTION 2*
Xpresskit (2-way D2D)
OPTION 3
Fortin (1-way D2D)
FUNCTION 5 – Push-To-Start option
OPTION 1
PTS ENABLED
OPTION 2*
PTS DISABLED
OPTION 3
Push-To-Start ENABLED with takeover within 1.5 min.
OPTION 4
Push-To-Start ENABLED with takeover within 3 min.
1. In programming mode (page 3).
2. Before the lights go out, press and hold the brake pedal and press the LOCK and UNLOCK buttons
simultaneously  the parking lights will flash 4 times. At that point, release the brake pedal.
3. Start up the engine and allow the vehicle to reach regular engine idle speed.
4. Once the engine is running at normal idle speed, press the brake pedal and keep it down until you hear the
parking lights output click 5 times.
5. Release the brake pedal the tach programming is now complete.
Caution! – Tach jumper settings:
Some new vehicles have a higher TACH voltage threshold, which would fall out of the normal TACH trigger
circuit of the remote car starter. Changing the jumper to TACH Threshold HIGH will allow the module to
properly detect the TACH signal. BUT, if you are having trouble with the TACH, please call our tech support
team. Problems requiring changing the TACH jumper settings are very rare.
TRANSPONDER PROGRAMMING
This procedure is detailed in the full installation guide. To obtain a copy of the installation guide, please visit our
website at www.autostart.ca.
RESETTING THE MODULE
WARNING!
By resetting the module, all programmed values are erased  i.e.: tach, transmitter as well as
programming options. The programming options are returned to their default values.
1. Enter programming Mode (page 3).
2. Once having reached the programming mode, quickly press and release the brake pedal until the parking
HORN ADJUSTMENT
1.
2.
lights flash 8 times.
BYPASS
Remote starters of this series have the ability to work in two way mode (D2D) with Xpresskit bypass modules.
They also offer one way communication with Xpresskit, ADS and Fortin brand bypass modules. Note: For
Hardware 5.0 and higher there can only be one bypass connected to the unit.
3.
4.
5.
6.
P.6
http://www.autostart.ca
Quick Installation Guide
Note: Before adjustment, horn option must be enabled.
In programming mode (page 3).
Press and hold the brake pedal, then simultaneously press the UNLOCK and START buttons  the
horn will chirp 5 times.
Release the brake pedal.
To change the timing:
1. To increase the horn pulse by 3 ms, press the LOCK button.
2. To decrease the pulse by 3 ms, press the UNLOCK button.
3. To increase the pulse by 10 ms, press the START button.
4. To decrease the pulse by 10 ms, press the TRUNK button.
To save the new settings: press LOCK and UNLOCK simultaneously. If 3 chirps are returned, the new
setting has been saved.
You have 20 more seconds to select one of the sub-menus if needed.
Quick installation Guide
http://www.autostart.ca
P.5
WIRING SCHEMATIC
REAR VIEW OF THE MODULE
Yellow loop
WARNING!
Parking lights jumper in
Neutral position
ADS & Fortin
bypass
Positive Parking lights
INV 200
(Door lock pulse
inverter)
DO NOT SET
THE BLUE JUMPER TO
A HORIZONTAL POSITION
SIDE VIEW OF THE MODULE
Negative Parking lights
Optional programming
port / SmartStart
Jumper for Starter 2
Jumper for Ignition 2
Jumper for Accessories 2
Xpresskit bypass
1
Programming Button
TACH Threshold: HIGH
TACH Threshold: NORMAL
N/A
1. GREY/LIGHT BLUE.... (-) AUX2 output
2. BLUE/WHITE...............(-) AUX1 output
3. YELLOW/WHITE......... (-) Negative Ignition output
For Automatic transmissions:
Cut the yellow loop before plugging
the module.
YELLOW.................IGNITION
30 A Fuse
RED................+12V (Battery)
ORANGE......ACCESSORIES
(Heater Blower Motor)
PURPLE.................STARTER
GREEN.................5TH RELAY
30 A Fuse
RED................+12V (Battery)
15 A Fuse
1- BLACK..........................GROUND (-)
2- PURPLE...........................TACH (AC)
3- GREY...................HOOD SWITCH (-)
4- ORANGE...........BRAKE SWITCH (+)
5- YELLOW.......PARKING LIGHTS (+/-)
12- YELLOW ..................(+) Glow plug input
11- GREY ....................... (-) NEG. Door input
10- WHITE ..................... (-) GROUND when running
9- PURPLE .................... (-) EXT. TRIGGER output
8- ORANGE ................... (-) Parking Brakes input
7- WHITE/ORANGE .......(-) Starter kill output
6- BLUE/WHITE .............(+) POS. Door input
5- WHITE/GREEN ..........(-) DISARM output / PTS output
4- WHITE/BROWN .........(-) REARM output
3- GREEN ...................... (-) UNLOCK output
2- BROWN ..................... (-) LOCK output
1- BLUE ......................... (-) TRUNK output
V0.04 FcN - July 5, 2011