GA-7VASFS-FS
AMD Socket A Processor Motherboard
USER'S MANUAL
Pentium®4 Processor Motherboard
Rev. 0201
12ME-7VASFS-0201
English
Table of Content
Item Checklist .......................................................................................... 4
Chapter 1 Introduction ............................................................................. 5
Features Summary ....................................................................................... 5
GA-7VASFS-FS Motherboard Layout ........................................................... 7
Block Diagram .............................................................................................. 8
Chapter 2 Hardware Installation Process .............................................. 10
Step 1: Install the Central Processing Unit (CPU) ...................................... 11
Step1-1: CPU Speed Setup ............................................................................................... 11
Step1-2: CPU Installation ................................................................................................. 12
Step1-3: CPU Heat Sink Installation ................................................................................ 13
Step 2: Install memory modules ................................................................. 14
Step 3: Install expansion cards .................................................................. 16
Step 4: Connect ribbon cables, cabinet wires, and power supply .............. 17
Step 4-1: I/O Back Panel Introduction .............................................................................. 17
Step 4-2: Connectors & Jumper Setting Introduction ....................................................... 19
Chapter 3 BIOS Setup ..........................................................................31
The Main Menu (For example: BIOS Ver. : D5) .......................................... 32
Standard CMOS Features .......................................................................... 34
Advanced BIOS Features ........................................................................... 37
Integrated Peripherals ............................................................................... 39
Power Management Setup ......................................................................... 42
GA-7VASFS-FS Motherboard
-2-
PC Health Status ........................................................................................ 45
Frequency/Voltage Control ......................................................................... 46
Load Fail-Safe Defaults .............................................................................. 47
Load Optimized Defaults ............................................................................ 48
Set Supervisor/User Password .................................................................. 49
Save & Exit Setup ...................................................................................... 50
Exit Without Saving ................................................................................... 51
-3-
Table of Content
English
PnP/PCI Configurations ............................................................................. 44
English
Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. To
protect them against damage from static electricity, you should follow some precautions whenever you
work on your computer.
1.
Unplug your computer when working on the inside.
2.
Use a grounded wrist strap before handling computer components. If you do not have
one, touch both of your hands to a safely grounded object or to a metal object, such as
the power supply case.
3.
Hold components by the edges and try not touch the IC chips, leads or connectors, or
other components.
4.
Place components on a grounded antistatic pad or on the bag that came with the
components whenever the components are separated from the system.
5.
Ensure that the ATX power supply is switched off before you plug in or remove the ATX
ower connector on the motherboard.
Installing the motherboard to the chassis…
If the motherboard has mounting holes, but they don't line up with the holes on the base and there
are no slots to attach the spacers, do not become alarmed you can still attach the spacers to the
mounting holes. Just cut the bottom portion of the spacers (the spacer may be a little hard to cut off, so
be careful of your hands). In this way you can still attach the motherboard to the base without worrying
about short circuits. Sometimes you may need to use the plastic springs to isolate the screw from the
motherboard PCB surface, because the circuit wire may be near by the hole. Be careful, don't let the
screw contact any printed circuit write or parts on the PCB that are near the fixing hole, otherwise it may
damage the board or cause board malfunctioning.
GA-7VASFS-FS Motherboard
-4-
Features Summary
Form Factor
CPU
Chipset
Memory
I/O Control
Slots
On-Board IDE
On-Board Peripherals
y 30.4cm x 24.4cm ATX size form factor, 4 layers PCB.
y Socket A processor
AMD AthlonTM/AthlonTM XP/ DuronTM (K7)
128K L1 & 256K/64K L2 cache on die
266/333/400 MHz FSB and DDR bus speeds
y Supports 1.4GHz and faster
y VIA KT600 Memory/AGP/PCI Controller (PAC)
y VIA VT8237 Integrated Peripheral Controller (PSIPC)
y 3 184-pin DDR sockets
y Supports DDR DRAM PC1600/PC2100/PC2700/PC3200<Note 2>
y Supports up to 1.5GB DDR (Max)
y Supports only 2.5V DDR DIMM
y IT8705
y 1 AGP slot 4X (1.5V) / 8X(0.8V) device support
y 5 PCI slot supports 33MHz & PCI 2.2 compliant
y 2 IDE bus master (UDMA33/ATA66/ATA100) IDE ports
for up to 4 ATAPI devices
y Supports PIO mode3,4 (UDMA 33/ATA66/ATA100) IDE
& ATAPICD-ROM
y 1 Floppy port supports 2 FDD with 360K, 720K,1.2M, 1.44M
and 2.88M bytes.
y 1 Parallel port supports Normal/EPP/ECP mode
y 1 Serial port (COMA), 1 SPDIF port, COMB on Board
y 2 IEEE 1394 port
y 8 USB 2.0/1.1 ports (4 x Rear, 4 xFront by cable)
y 1 Front Audio Connector
y 2 Serial ATA Connector
to be continued......
-5-
Introduction
English
Chapter 1 Introduction
English
Hardware Monitor
y
y
y
y
CPU/Power/System Fan Revolution detect
CPU/Power/System Fan Fail Warning
CPU Overheat Warning
System Voltage Detect
On-Board Sound
y Realtek ALC655 CODEC
y Line Out / 2 front speaker
y Line In / 2 rear speaker(by s/w switch)
y Mic In / center& subwoofer(by s/w switch)
On-Board LAN
y AUX_In
y Build in RTL8101L Chipset
On-Board IEEE1394
PS/2 Connector
y VT6307
y PS/2 Keyboard interface and PS/2 Mouse interface
BIOS
y Licensed AWARD BIOS
y Supports Q-Flash
Additional Features
y PS/2 Keyboard power on by password
y PS/2 Mouse power on
y STR(Suspend-To-RAM)
y AC Recovery
y USB KB/Mouse wake up from S3
y Acoustic Management for hard drive and optical drive
Please set the CPU host frequency in accordance with your processor's specifications.
We don't recommend you to set the system bus frequency over the CPU's specification
because these specific bus frequencies are not the standard specifications for CPU,
chipset and most of the peripherals. Whether your system can run under these specific
bus frequencies properly will depend on your hardware configurations, including CPU,
Chipsets,SDRAM,Cards...etc.
GA-7VASFS-FS Motherboard
-6-
English
GA-7VASFS-FS Motherboard Layout
KB_MS
RAM_LED
CPU_FAN
FDD
USB_1394
ATX
GA-7VASFS-FS
COMA
SOCKET A
PWR_FAN
ATX_12V
AUX_IN
AGP
DDR2
KT600
DDR3
AUDIO
DDR1
F_AUDIO
IDE1
USB_LAN
IDE2
LPT
SPDIF
CODCE
BAT
PCI1
SW1
S_ATA1
VT8237
S_IRQ
CI
RTL8101L
S_ATA0
CLR_CMOS
PCI2
BZ
PCI3
IT8705
VT6307
SYS_FAN
PCI4
PWR_LED
FS
BIOS
F_USB2
PCI5
CNR
-7-
F_1394
F_PANEL
F_USB1
Introduction
CPUCLK+/- (100/133/166MHz)
AMD-K7TM
AGP 2X/4X/8X
System Bus100/133/166 MHz
AGPCLK
(66MHz)
DDR RAM
VIA
KT600
66MHz V_Link
5 PCI
HCLK+/- (100/133/166MHz)
AGPCLK66MHz
33 MHz
14.318 MHz
48 MHz
BIOS
VIA
VT8237
1394
AC97 Link
Floppy
IT8705
LPT Port
PS/2 KB/Mouse
ATA66/100/133
IDE Channels
8 USB
Ports
24 MHz
33 MHz
COM Port
PCICLK (33MHz)
USBCLK (48MHz)
14.318 MHz
33 MHz
GA-7VASFS-FS Motherboard
Serial ATA
Channels
LINE-OUT
MIC
PCICLK
(33MHz)
AC97
CODEC
LINE-IN
English
Block Diagram
CLK
GEN
-8-
HCLK+/- (100/133/166MHz)
CPUCLK+/- (100/133/166MHz)
AGPCLK (66MHz)
V_Link (66MHz)
English
-9-
Introduction
To set up your computer, you must complete the following steps:
Step 1- Set system Switch (SW1)
Step 2- Install the Central Processing Unit (CPU)
Step 3- Install memory modules
Step 4- Install expansion cards
Step 5- Connect ribbon cables, cabinet wires, and power supply
Step 4
Step 1
Step 2
Step 4
Step 4
Step 3
FS
English
Chapter 2 Hardware Installation Process
Congratulations you have accomplished the hardware installation!
Turn on the power supply or connect the power cable to the power outlet. Continue with the BIOS/
software installation.
GA-7VASFS-FS Motherboard
- 10 -
Step1-1: CPU Speed Setup
The system bus frequency can be switched at 100/133/166/200MHz by adjusting system switch
FS
(SW1). (The internal frequency depend on CPU.)
O: ON / X :OFF
1
SW1
Default Setting: 100MHz
ON
SW1
CPU CLOCK
1
100MHz
ON
100MHz : Fix FSB 200MHz CPU
Auto : Support FSB 266/333/400 MHz CPU
You must set SW1 to 100MHz when
Auto
OFF
you used FSB 200MHz CPU.
- 11 -
Hardware Installation Process
English
Step 1: Install the Central Processing Unit (CPU)
English
Step1-2: CPU Installation
Before installing the processor, adhere to the following warning:
1.Please make sure the CPU type is supported by the motherboard.
2.If you do not match the CPU socket Pin 1 and CPU cut edge well, it will
cause improper installation. Please change the insert orientation.
CPU Top View
CPU Bottom View
Socket Actuation Lever
Pin1 indicator
2. Locate Pin 1 in the socket and look
for a (golden) cut edge on the CPU
1. Pull up the CPU socket lever
and up to 90-degree angle.
GA-7VASFS-FS Motherboard
upper corner. Then insert the CPU
into the socket.
- 12 -
Before installing the CPU Heat Sink , adhere to the following warning:
1. Please use AMD approved cooling fan.
2. We recommend you to apply the thermal paste to provide better heat
conduction between your CPU and Cooling Fan.
3. Make sure the CPU fan power cable is plugged in to the CPU fan connector, this
completes the installation.
Please refer to CPU cooling fan user's manual for more detail installation
procedure.
2. Use qualified fan approved by AMD.
1. Press down the CPU socket
lever and finish CPU installation.
3. Fasten the heatsink supporting-base
4. Make sure the CPU fan is plugged
onto the CPU socket on the mainboard.
to the CPU fan connector, than install
complete.
- 13 -
Hardware Installation Process
English
Step1-3: CPU Heat Sink Installation
Before installing the memory modules, adhere to the following warning:
1. When RAM_LED is ON, do not install / remove DIMM from socket.
2. Please note that the DIMM module can only fit in one direction due to the one
notch. Wrong orientation will cause improper installation. Please change the
insert orientation.
The motherboard has 3 dual inline memory module(DIMM) sockets. The BIOS will automatically detects memory type and size. To install the memory module, just push it vertically into the
DIMM Slot. The DIMM module can only fit in one direction due to the notch. Memory size can vary
between sockets.
Notch
DDR
FS
English
Step 2: Install memory modules
Support Unbuffered DDR DIMM Sizes type:
64 Mbit (2Mx8x4 banks)
64 Mbit (1Mx16x4 banks)
128 Mbit(2Mx16x4 banks)
512 Mbit(16Mx8x4 banks)
256 Mbit(8Mx8x4 banks)
512 Mbit(8Mx16x4 banks)
128 Mbit(4Mx8x4 banks)
256 Mbit(4Mx16x4 banks)
Only two double side DDR 400 memory modules are allowed to be used!
GA-7VASFS-FS Motherboard
- 14 -
English
1. The DIMM slot has a notch, so the DIMM
memory module can only fit in one direction.
2. Insert the DIMM memory module vertically into
the DIMM slot. Then push it down.
3. Close the plastic clip at both edges of the DIMM
slots to lock the DIMM module.
Reverse the installation steps when you wish
to remove the DIMM module.
DDR Introduction
Established on the existing SDRAM infrastructure, DDR (Double Data Rate) memory is a high
performance and cost-effective solution that allows easy adoption for memory vendors, OEMs,
and system integrators.
DDR memory is a great evolutionary solution for the PC industry that builds on the existing
SDRAM architecture, yet make the awesome advances in solving the system performance
bottleneck by doubling the memory bandwidth. Nowadays, with the highest bandwidth of
3.2GB/s of DDR400 memory and complete line of DDR400/333/266/200 memory solutions, DDR
memory is the best choice for building high performance and low latency DRAM subsystem that
are suitable for servers, workstations, and full range of desktop PCs.
- 15 -
Hardware Installation Process
English
Step 3: Install expansion cards
1. Read the related expansion card's instruction document before install the expansion card into
the computer.
2. Remove your computer's chassis cover, necessary screws and slot bracket from the computer.
3. Press the expansion card firmly into expansion slot in motherboard.
4. Be sure the metal contacts on the card are indeed seated in the slot.
5. Replace the screw to secure the slot bracket of the expansion card.
6. Replace your computer's chassis cover.
7. Power on the computer, if necessary, setup BIOS utility of expansion card from BIOS.
8. Install related driver from the operating system.
AGP Card
Please carefully pull out the small white- drawable bar
at the end of the AGP slot when you try to install/
Uninstall the AGP card. Please align the AGP card to
the onboard AGP slot and press firmly down on the slot
.Make sure your AGP card is locked by the small whitedrawable bar.
Issues To Beware Of When Installing CNR
Please use standard CNR card like the one in order to avoid mechanical problem.
Standard CNR Card
GA-7VASFS-FS Motherboard
- 16 -
Step 4-1: I/O Back Panel Introduction
X
Z
Y
\
[
X PS/2 Keyboard and PS/2 Mouse Connector
PS/2 Mouse Connector
(6 pin Female)
¾This connector supports standard PS/2 keyboard
and PS/2 mouse.
PS/2 Keyboard Connector
(6 pin Female)
YIEEE 1394 and USB Connector
¾This connector supports IEEE 1394 and USB
devices.
1394
USB 0
USB 1
ZParallel Port, Serial Port and SPDIF Port (LPT/COMA/SPDIF)
Parallel Port
(25 pin Female)
¾ This connector supports 1 standard COM port,
1 Parallel port and 1 SPDIF port. Device like
printer can be connected to Parallel port;
mouse and modem etc can be connected to
Serial ports.
The SPDIF output is capable of providing
SPDIF Port
digital audio to external speakers or com
pressed AC3 data to an external Dolby Digital
COMA
Serial Port
(9 pin Male)
Decoder. Use this feature only when your
stereo system has digital input function.
- 17 -
Hardware Installation Process
English
Step 4: Connect ribbon cables, cabinet wires, and power
supply
English
[ USB & LAN Connector
¾ Before you connect your device(s) into USB
connector(s), please make sure your device(s)
such as USB keyboard,mouse, scanner, zip,
speaker..etc. Have a standard USB interface.
LAN
Also make sure your OS supports USB
controller.
USB 0
If your OS does not support USB controller,
please contact OS vendor for possible patch
USB 1
or driver upgrade. For more information please
contact your OS or device(s) vendors.
\ Audio Connectors
¾ After install onboard audio driver, you may
connect speaker to Line Out jack, micro phone
Line In(Rear Speaker)
to MIC In jack.
Device like CD-ROM , walkman etc can be
Line Out(Front Speaker)
connected to Line-In jack.
MIC In(Center and Subwoofer) Please note:
You are able to use 2-/4-/6- channel audio
feature by S/W selection.
If you want to enable 6-channel function, you
have 2 choose for hardware connection.
Method1:
Connect "Front Speaker" to "Line Out"
Connect "Rear Speaker" to "Line In"
Connect "Center and Subwoofer" to "MIC Out".
GA-7VASFS-FS Motherboard
- 18 -
1
3
English
Step 4-2: Connectors & Jumper Setting Introduction
9
2
7
5
6
13
14
12
17
8
18
19
4
FS
11
10
16
1) ATX_12V
2) ATX
3) CPU_FAN
4) SYS_FAN
5) PWR_FAN
6) IDE1/IDE2
7) FDD
8) S_ATA0/S_ATA1
9) RAM_LED
10) PWR_LED
11) F_PANEL
15
12) BAT
13) F_AUDIO
14) AUX_IN
15) F_USB1/F_USB2
16) F_1394
17) S_IRQ
18) CI
19) CLR_CMOS
- 19 -
Hardware Installation Process
This connector (ATX _12V) suppliesthe CPU operation voltage (Vcore). If this " ATX_ 12V connector" is
not connected, system cannot boot.
4
1
2
Pin No.
1
2
3
4
Definition
GND
GND
+12V
+12V
FS
3
2) ATX (ATX Power)
AC power cord should only be connected to your power supply unit after ATX power cable and other
related devices are firmly connected to the mainboard.
10
1
FS
English
1) ATX_12V (+12V Power Connector)
GA-7VASFS-FS Motherboard
- 20 -
20
11
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Definition
3.3V
3.3V
GND
VCC
GND
VCC
GND
Power Good
5V SB(stand by +5V)
+12V
3.3V
-12V
GND
PS_ON(softOn/Off)
GND
GND
GND
-5V
VCC
VCC
Please note, a proper installation of the CPU cooler is essential to prevent the CPU from running
under abnormal condition or damaged by overheating.The CPU fan connector supports Max.
current up to 600 mA.
Definition
GND
+12V
Sense
FS
1
Pin No.
1
2
3
4) SYS_FAN (System FAN Connector)
This connector allows you to link with the cooling fan on the system case to lower the system
temperature.
Definition
GND
+12V
Sense
FS
1
Pin No.
1
2
3
- 21 -
Hardware Installation Process
English
3) CPU_FAN (CPU FAN Connector)
This connector allows you to link with the cooling fan on the system case to lower the system
temperature.
Pin No.
1
2
3
FS
1
Definition
GND
+12V
Sense
6) IDE1/ IDE2 (IDE1/IDE2 Connector)
Please connect first harddisk to IDE1 and connect CDROM to IDE2. The red stripe of the ribbon cable
must be the same side with the Pin1.
39
40
2
1
GA-7VASFS-FS Motherboard
- 22 -
IDE2
IDE1
FS
English
5) PWR_FAN (Power Fan Connector)
Please connect the floppy drive ribbon cables to FDD. It supports 360K,720K,1.2M,1.44M and
2.88Mbytes floppy disk types. The red stripe of the ribbon cable must be the same side with the Pin1.
34
1
FS
2
33
8) S_ATA0/S_ATA1 (Serial ATA Connector)
You can connect the Serial ATA device to this connector, it provides you high speed transfer rates
(150MB/sec).If you wish to use SATA0 and SATA1, please Enable " OnChip Serial ATA " item.
Then, install the correct driver to have proper operation. For details, please refer to the
"VT8237_SATA_Manual.pdf" at "http:\\www.gigabyte.com.tw"
1
Definition
GND
TXP
TXN
GND
RXN
RXP
GND
FS
7
Pin No.
1
2
3
4
5
6
7
- 23 -
Hardware Installation Process
English
7) FDD (Floppy Connector)
Do not remove memory modules while DIMM LED is on. It might cause short or other unexpected
damages due to the 2.5V stand by voltage. Remove memory modules only when AC Power cord is
disconnected.
+
FS
-
10) PWR_LED
PWR_LED is connect with the system power indicator to indicate whether the system is on/off. It will blink
when the system enters suspend mode. If you use dual color LED, power LED will turn to another color.
1
FS
English
9) RAM_LED
GA-7VASFS-FS Motherboard
- 24 -
Pin No.
1
2
3
Definition
MPD+
MPDMPD-
Please connect the power LED, PC peaker, reset switch and power switch etc of your chassis front panel
to the F_PANEL connector according to the pin assignment above.
Speaker
Connector
20 19
SPEAKReset Switch
Soft Power
Connector
SPEAK+
1
PWPW+
MSGMSG+
1
1
RES+
RESHDHD+
IDE Hard Disk
Active LED
FS
Message LED/Power/
Sleep LED
11
2 1
NC
HD (IDE Hard Disk Active LED)
Pin 1: LED anode(+)
(Blue)
Pin 2: LED cathode(-)
SPK (Speaker Connector)
Pin 1: VCC(+)
(Amber)
Pin 2- Pin 3: NC
RES (Reset Switch)
Open: Normal Operation
Pin 4: Data(-)
(Green)
Close: Reset Hardware System
PW (Soft Power Connector)
Open: Normal Operation
(Red)
Close: Power On/Off
MSG(Message LED/Power/
Pin 1: LED anode(+)
Sleep LED)(Yellow)
Pin 2: LED cathode(-)
NC( Purple)
NC
- 25 -
Hardware Installation Process
English
11) F_PANEL (2x10 pins connector)
+
CAUTION
FS
™ Danger of explosion if battery is incorrectly
replaced.
™ Replace only with the same or equivalent
type recommended by the manufacturer.
™ Dispose of used batteries according to the
manufacturer's instructions.
If you want to erase CMOS...
1.Turn OFF the computer and unplug the power cord.
2.Remove the battery, wait for 30 second.
3.Re-install the battery.
4.Plug the power cord and turn ON the computer.
13) F_AUDIO (F_AUDIO Connector)
If you want to use Front Audio connector, you must remove 5-6, 9-10 Jumper. In order to utilize the
front audio header, your chassis must have front audio connector. Also please make sure the pin
assigment on the cable is the same as the pin assigment on the MB header. To find out if the chassis
you are buying support front audio connector, please contact your dealer.Please note, you can have the
alternative of using front audio connector or of using rear audio connector to play sound.
FS
English
12) BAT (Battery)
GA-7VASFS-FS Motherboard
- 26 -
10
9
2
1
Pin No.
1
2
3
4
5
6
7
8
9
10
Definition
MIC
GND
REF
POWER
FrontAudio (R)
RearAudio (R)
Reserved
No Pin
FrontAudio (L)
RearAudio (L)
English
14) AUX_IN (AUX In Connector)
Connect other device(such as PCI TV Tunner audio out)to the connector.
Pin No.
1
2
3
4
FS
1
Definition
AUX-L
GND
GND
AUX_R
15) F_ USB1 / F_USB2 (Front USB Connector, Yellow)
Be careful with the polarity of the front USB connector. Check the pin assignment while you
connect the front USB cable. Please contact your nearest dealer for optional front USB cable.
Be careful with the polarity of the F_USB connector. Check the pin assignment carefully while you
connect the F_USB cable, incorrect connection between the cable and connector will make the device
unable to work or even damage it. For optional F_USB cable, please contact your local dealer.
10
1
9
Definition
Power
Power
USB DXUSB DyUSB DX+
USB Dy+
GND
GND
No Pin
NC
FS
2
Pin No.
1
2
3
4
5
6
7
8
9
10
- 27 -
Hardware Installation Process
Please Note: Serial interface standard set by Institute of Electrical and Electronics Engineers, which
has features like high speed, high bandwidth and hot plug.
10
1
9
Definition
NDCDBNSINB
NSOUTB
NDTRBGND
NDSRBNRTSBNCTSBNRIBNo Pin
FS
2
Pin No.
1
2
3
4
5
6
7
8
9
10
17) S_IRQ (Serial IRQ Connector)
This connector is for special design, for example: PCMCIA add on card.
1
FS
English
16) F_1394 (IEEE 1394 Connector)
GA-7VASFS-FS Motherboard
- 28 -
Pin No. Definition
1
Signal
2
GND
This 2 pin connector allows your system to enable or disable the "case open" item in BIOS if the
system case begin remove.
Pin No. Definition
1
Signal
2
GND
FS
1
19) CLR_CMOS (Clear CMOS jumper)
You may clear the CMOS data to its default values by this jumper. Default doesn’t include the
"Shunter" to prevent from improper use this jumper. To Clear CMOS, temporarily short 1-2 pin.
1-2 close: Enable
1
2-3 open: Normal (Default)
FS
1
- 29 -
Hardware Installation Process
English
18) CI (CASE OPEN)
English
GA-7VASFS-FS Motherboard
- 30 -
BIOS Setup is an overview of the BIOS Setup Program. The program that allows users to modify the
basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it
retains the Setup information when the power is turned off.
ENTERING SETUP
Powering ON the computer and pressing <Del> immediately will allow you to enter Setup. If you require
more advanced BIOS settings, please go to "Advanced BIOS" setting menu.To enter Advanced BIOS
setting menu, press "Ctrl+F1" key on the BIOS screen.
CONTROL KEYS
<Ç>
Move to previous item
<È>
Move to next item
<Å>
Move to the item in the left hand
<Æ>
Move to the item in the right hand
Enter
Select item
<Esc>
Main Menu - Quit and not save changes into CMOS Status Page Setup Menu and
Option Page Setup Menu - Exit current page and return to Main Menu
<+/PgUp> Increase the numeric value or make changes
<-/PgDn>
Decrease the numeric value or make changes
<F1>
General help, only for Status Page Setup Menu and Option Page Setup Menu
<F2>
Item Help
<F3>
Reserved
<F4>
Reserved
<F5>
Restore the previous CMOS value from CMOS, only for Option Page Setup Menu
<F6>
Load the file-safe default CMOS value from BIOS default table
<F7>
Load the Optimized Defaults
<F8>
Q-Flash function
<F9>
System Information
<F10>
Save all the CMOS changes, only for Main Menu
- 31 -
BIOS Setup
English
Chapter 3 BIOS Setup
English
GETTING HELP
Main Menu
The on-line description of the highlighted setup function is displayed at the bottom of the screen.
Status Page Setup Menu / Option Page Setup Menu
Press F1 to pop up a small help window that describes the appropriate keys to use and the possible
selections for the highlighted item. To exit the Help Window press <Esc>.
The Main Menu (For example: BIOS Ver. : D5)
Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 1) will appear on the screen.
The Main Menu allows you to select from eight setup functions and two exit choices. Use arrow keys to
select among the items and press <Enter> to accept or enter the sub-menu.
CMOS Setup Utility-Copyright (C) 1984-2003 Award Software
Standard CMOS Features
Load Fail-Safe Defaults
Advanced BIOS Features
Load Optimized Defaults
Integrated Peripherals
Set Supervisor Password
Power Management Setup
Set User Password
PnP/PCI Configurations
Save & Exit Setup
PC Health Status
Exit Without Saving
Frequency/Voltage Control
ESC:Quit
:Select Item
F8: Q-Flash
F10:Save & Exit Setup
Time, Date, Hard Disk Type...
Figure 1: Main Menu
If you can't find the setting you want, please press "Ctrl+F1" to
search the advanced option widden.
z
Standard CMOS Features
This setup page includes all the items in standard compatible BIOS.
z
Advanced BIOS Features
This setup page includes all the items of Award special enhanced features.
GA-7VASFS-FS Motherboard
- 32 -
Integrated Peripherals
English
z
This setup page includes all onboard peripherals.
z
Power Management Setup
This setup page includes all the items of Green function features.
z
PnP/PCI Configurations
This setup page includes all the configurations of PCI & PnP ISA resources.
z
PC Health Status
This setup page is the System auto detect Temperature, voltage, fan, speed.
z
Frequency/Voltage Control
This setup page is control CPU's clock and frequency ratio.
z
Load Fail-Safe Defaults
Fail-Safe Defaults indicates the value of the system parameters which the system would
be in safe configuration.
z
Load Optimized Defaults
Optimized Defaults indicates the value of the system parameters which the system would
be in best performance configuration.
z
Set Supervisor password
Change, set, or disable password. It allows you to limit access to the system and Setup,
or just to Setup.
z
Set User password
Change, set, or disable password. It allows you to limit access to the system.
z
Save & Exit Setup
Save CMOS value settings to CMOS and exit setup.
z
Exit Without Saving
Abandon all CMOS value changes and exit setup.
- 33 -
BIOS Setup
English
Standard CMOS Features
CMOS Setup Utility-Copyright (C) 1984-2003 Award Software
Standard CMOS Features
Date (mm:dd:yy)
Tue, Aug 13 2002
Item Help
Time (hh:mm:ss)
22:31:24
Menu Level
Change the day, month,
IDE Primary Master
[None]
IDE Primary Slave
[None]
year
IDE Secondary Master
[None]
<Week>
IDE Secondary Slave
[None]
Sun. to Sat.
Acoustic Management
[Disabled]
Drive A
[1.44M, 3.5 in.]
<Month>
Drive B
[None]
Jan. to Dec.
Floppy 3 Mode Support
[Disabled]
Halt On
[All, But Keyboard]
<Day>
1 to 31 (or maximum
allowed in the month)
Base Memory
640K
Extended Memory
130048K
<Year>
Total Memory
131072K
1999 to 2098
: Move
Enter:Select
+/-/PU/PD:Value
F5:Previous Values
F10:Save
ESC:Exit
F6:Fail-Safe Defaults
F1:General Help
F7:Optimized Defaults
Figure 2: Standard CMOS Features
Date
The date format is <week>, <month>, <day>, <year>.
Week
The week, from Sun to Sat, determined by the BIOS and is display only
Month
The month, Jan. Through Dec.
Day
The day, from 1 to 31 (or the maximum allowed in the month)
Year
The year, from 1999 through 2098
Time
The times format in <hour> <minute> <second>. The time is calculated base on the 24-hour militarytime clock. For example, 1 p.m. is 13:00:00.
GA-7VASFS-FS Motherboard
- 34 -
The category identifies the types of hard disk from drive C to F that has been installed in the computer.
There are two types: auto type, and manual type. Manual type is user-definable; Auto type which will
automatically detect HDD type.
Note that the specifications of your drive must match with the drive table. The hard disk will not work
properly if you enter improper information for this category.
If you select User Type, related information will be asked to enter to the following items. Enter the
information directly from the keyboard and press <Enter>. Such information should be provided in the
documentation form your hard disk vendor or the system manufacturer.
CYLS.
Number of cylinders
HEADS
Number of heads
PRECOMP
Write precomp
LANDZONE
Landing zone
SECTORS
Number of sectors
If a hard disk has not been installed select NONE and press <Enter>.
Acoustic Management
As well as hard disk and optical date drives such as CD-ROM, CD-RW and DVD are also
responsible for generating noise in the PC. Therefore the BIOS support the acoustic management feature
to reduce the noise. In the Standard CMOS Features please select the IDE drive, which should be
support the Acoustic management and press Enter. When the IDE device can support the acoustic
management then you can see this option in the BIOS setup. The following options are available:
Hard Drive
Disabled: full hard disk performance with maximum noise generation (default)
Silent:
lower hard disk performance with minimum noise generation
Optical Drive Disabled: the device can rotate at maximum speed with maximum noise generation
Medium: the device can rotate at no higher than medium speed with medium noise
generation (default)
Silent:
the device can rotate at minimum speed only with minimum noise generation
For optimal performance for hard drive and optical drive please disabled the acoustic management.
Drive A / Drive B
The category identifies the types of floppy disk drive A or drive B that has been installed in the
computer.
- 35 -
BIOS Setup
English
IDE Primary Master, Slave / IDE Secondary Master, Slave
English
None
No floppy drive installed
360K, 5.25 in.
5.25 inch PC-type standard drive; 360K byte capacity.
1.2M, 5.25 in.
5.25 inch AT-type high-density drive; 1.2M byte capacity
(3.5 inch when 3 Mode is Enabled).
720K, 3.5 in.
3.5 inch double-sided drive; 720K byte capacity
1.44M, 3.5 in.
3.5 inch double-sided drive; 1.44M byte capacity.
2.88M, 3.5 in.
3.5 inch double-sided drive; 2.88M byte capacity.
Floppy 3 Mode Support (for Japan Area)
Disabled
Normal Floppy Drive. (Default value)
Drive A
Drive A is 3 mode Floppy Drive.
Drive B
Drive B is 3 mode Floppy Drive.
Both
Drive A & B are 3 mode Floppy Drives.
Halt on
The category determines whether the computer will stop if an error is detected during power up.
NO Errors
The system boot will not stop for any error that may be detected
and you will be prompted.
All Errors
Whenever the BIOS detects a non-fatal error the system will be stopped.
All, But Keyboard
The system boot will not stop for a keyboard error; it will stop for
all other errors. (Default value)
All, But Diskette
The system boot will not stop for a disk error; it will stop for all
other errors.
All, But Disk/Key
The system boot will not stop for a keyboard or disk error; it will
stop for all other errors.
Memory
The category is display-only which is determined by POST (Power On Self Test) of the BIOS.
GA-7VASFS-FS Motherboard
- 36 -
The POST of the BIOS will determine the amount of base (or conventional)
memory installed in the system.
The value of the base memory is typically 512 K for systems with 512 K memory
installed on the motherboard, or 640 K for systems with 640 K or more memory
installed on the motherboard.
Extended Memory
The BIOS determines how much extended memory is present during the POST.
This is the amount of memory located above 1 MB in the CPU's memory
address map.
Advanced BIOS Features
CMOS Setup Utility-Copyright (C) 1984-2003 Award Software
Advanced BIOS Features
First Boot Device
[CDROM]
Item Help
Second Boot Device
[Floppy]
Menu Level
Third Boot Device
[HDD-0]
Select Boot Device
Password Check
[Setup]
priority
Full Screen LOGO Show
[Enabled]
[Floppy]
Boot from floppy
[LS120]
Boot from LS120
[HDD-0]
Boot from First HDD
[HDD-1]
Boot from second HDD
: Move
Enter:Select
F5:Previous Values
+/-/PU/PD:Value
F10:Save
ESC:Exit
F6:Fail-Safe Defaults
F1:General Help
F7:Optimized Defaults
Figure 3: Advanced BIOS Features
- 37 -
BIOS Setup
English
Base Memory
English
First / Second / Third Boot Device
Floppy
Select your boot device priority by Floppy.
LS120
Select your boot device priority by LS120.
HDD-0~3
Select your boot device priority by HDD-0~3.
SCSI
Select your boot device priority by SCSI.
CDROM
Select your boot device priority by CDROM.
ZIP
Select your boot device priority by ZIP.
USB-FDD
Select your boot device priority by USB-FDD.
USB-ZIP
Select your boot device priority by USB-ZIP.
USB-CDROM
Select your boot device priority by USB-CDROM.
USB-HDD
Select your boot device priority by USB-HDD.
LAN
Select your boot device priority by LAN.
Disabled
Select your boot device priority by Disabled.
Password Check
System
The system will not boot and will not access to Setup page if the correct
password is not entered at the prompt.
Setup
The system will boot but will not access to Setup page if the correct password
is not entered at the prompt. (Default value)
Full Screen LOGO Show
This feature allows you to show the company logo on the bootup screen.
Disabled
Shows the POST messages at boot.
Enabled
Shows the still image(LOGO) on the full screen at boot. (Default value)
GA-7VASFS-FS Motherboard
- 38 -
English
Integrated Peripherals
CMOS Setup Utility-Copyright (C) 1984-2003 Award Software
Integrated Peripherals
OnChip IDE Channel0
[Enabled]
Item Help
OnChip IDE Channel1
[Enabled]
Menu Level
OnChip Serial ATA
[Enabled]
If a hard disk
AC97 Audio
[Auto]
controller card is
MC97 Modem
[Auto]
used, set at Disabled
USB 1.1 Controller
[Enabled]
USB 2.0 Controller
[Enabled]
[Enabled]
USB Device Function
[Disabled]
Enable on-chip IDE
USB Keyboard Support
[Enabled]
Channel
USB Mouse Support
[Enabled]
Onboard H/W LAN
[Enabled]
[Disabled]
Onboard H/W 1394
[Enabled]
Disable on-chip IDE
Onboard Serial Port 1
[3F8/IRQ4]
Channel
Onboard Parallel Port
[378/IRQ7]
Parallel Port Mode
[EPP]
: Move
Enter:Select
F5:Previous Values
+/-/PU/PD:Value
F10:Save
ESC:Exit
F6:Fail-Safe Defaults
F1:General Help
F7:Optimized Defaults
Figure 4: Integrated Peripherals
OnChip IDE Channel0
Enabled
Enable onboard channel0 IDE port. (Default value)
Disabled
Disable onboard channel0 IDE port.
OnChip IDE Channel1
Enabled
Enable onboard channel1 IDE port. (Default value)
Disabled
Disable onboard channel1 IDE port.
- 39 -
BIOS Setup
English
OnChip Serial ATA
Disabled
Disable VT8237 Serial ATA.
Enabled
Enable VT8237 Serial ATA support. (Default Value)
AC97 Audio
Auto
Enable onboard AC'97 audio function. (Default Value)
Disabled
Disable this function.
MC97 Modem
Auto
Enable onboard MC97 controller. (Default Value)
Disabled
Disable this function.
USB 1.1 Controller
Disable this function if you are not using onboard USB 1.1 feature.
Enabled
Enable USB 1.1 Controller. (Default value)
Disabled
Disable USB 1.1 Controller.
USB 2.0 Controller
Disable this function if you are not using onboard USB 2.0 feature.
Enabled
Enable USB 2.0 Controller. (Default value)
Disabled
Disable USB 2.0 Controller.
USB Device Function
Enabled
Enable USB device function Support.
Disabled
Disable USB device function Support. (Default value)
USB Keyboard Support
Enabled
Enable USB Keyboard Support. (Default value)
Disabled
Disable USB Keyboard Support.
GA-7VASFS-FS Motherboard
- 40 -
Enabled
Enable USB Mouse Support.(Default value)
Disabled
Disable USB Mouse Support.
English
USB Mouse Support
Onboard H/W LAN
Enabled
Enable Onboard H/W LAN function. (Default value)
Disabled
Disable this function.
Onboard H/W 1394
Enabled
Enable onboard IEEE 1394 function.(Default value)
Disabled
Disable this function.
Onboard Serial Port 1
Auto
BIOS will automatically setup the port 1 address.
3F8/IRQ4
Enable onboard Serial port 1 and address is 3F8. (Default value)
2F8/IRQ3
Enable onboard Serial port 1 and address is 2F8.
3E8/IRQ4
Enable onboard Serial port 1 and address is 3E8.
2E8/IRQ3
Enable onboard Serial port 1 and address is 2E8.
Disabled
Disable onboard Serial port 1.
Onboard Parallel port
378/IRQ7
Enable onboard LPT port and address is 378/IRQ7. (Default Value)
278/IRQ5
Enable onboard LPT port and address is 278/IRQ5.
Disabled
Disable onboard LPT port.
3BC/IRQ7
Enable onboard LPT port and address is 3BC/IRQ7.
Parallel Port Mode
SPP
Using Parallel port as Standard Parallel Port.
EPP
Using Parallel port as Enhanced Parallel Port.
ECP
Using Parallel port as Extended Capabilities Port. (Default Value)
ECP+EPP
Using Parallel port as ECP & EPP mode.
- 41 -
BIOS Setup
English
Power Management Setup
CMOS Setup Utility-Copyright (C) 1984-2003 Award Software
Power Management Setup
ACPI Suspend Type
[S3(STR)]
Item Help
USB Device Wake-Up From S3
[Disabled]
Menu Level
Soft-Off by PWRBTN
[Instant-Off]
[S1]
AC BACK Function
[Memory]
Set suspend type to
Keyboard Power On
Mouse Power On
[Disabled]
[Disabled]
Power On Suspend under
ACPI OS
PME Event Wake Up
[Disabled]
Modem Ring Resume
[Disabled]
[S3]
Resume by Alarm
[Disabled]
Set suspend type to
x Date (of Month) Alarm
Everyday
Suspend to RAM under
x Time (hh:mm:ss)
0 0 0
ACPI OS
: Move
Enter:Select
+/-/PU/PD:Value
F5:Previous Values
F10:Save
ESC:Exit
F6:Fail-Safe Defaults
F1:General Help
F7:Optimized Defaults
Figure 5: Power Management Setup
ACPI Suspend Type
S1(POS)
Set ACPI suspend type to S1.
S3(STR)
Set ACPI suspend type to S3. (Default Value)
USB Device Wake-up From S3
When set at Enabled, it allows USB Device to activate the system from ACPI S3 power saving
mode.
Enabled
Enable USB Device Wakeup.
Disabled
Disable USB Device Wakeup. (Default Value)
Soft-Off by PWRBTN
Instant-off
Press power button then Power off instantly. (Default value)
Delay 4 Sec. Press power button 4 sec to Power off. Enter suspend if button is pressed less
than 4 sec.
GA-7VASFS-FS Motherboard
- 42 -
Memory
System power on depends on the status before AC lost. (Default value)
Soft-Off
Always in Off state when AC back.
Full-On
Always power on the system when AC back.
Keyboard Power On
Password
Enter from 1 to 8 characters to set the Keyboard Power On Password.
Disabled
Disabled this function. (Default value)
Keyboard 98
If your keyboard have "POWER Key" button, you can press the key to
power on your system.
Mouse Power On
Disabled
Disabled this function. (Default value)
Enabled
Double click on PS/2 mouse left button to power on system.
PME Event Wake Up
Disabled
Disable this function. (Default Value)
Enabled
Enable PME Event Wake up.
Modem Ring Resume
Disabled
Disable Modem Ring Resume function. (Default Value)
Enabled
Enable Modem Ring Resume function.
Resume by Alarm
You can set "Resume by Alarm" item to enabled and key in Data/time to power on system.
Disabled
Disable this function. (Default Value)
Enabled
Enable alarm function to POWER ON system.
If RTC Alarm Lead To Power On is Enabled.
Date ( of Month) Alarm :
Everyday, 1~31
Time ( hh: mm: ss) Alarm :
(0~23) : (0~59) : (0~59)
- 43 -
BIOS Setup
English
AC BACK Function
English
PnP/PCI Configurations
CMOS Setup Utility-Copyright (C) 1984-2003 Award Software
PnP/PCI Configurations
PNP OS Installed
[Yes]
Item Help
PCI 1/PCI 5 IRQ Assignment
[Auto]
Menu Level
PCI 2 IRQ Assignment
[Auto]
Select Yes if you are
PCI 3 IRQ Assignment
[Auto]
using a Plug and Play
PCI 4 IRQ Assignment
[Auto]
capable operating
system Select No if
you need the BIOS to
configure non-boot
devices
: Move
Enter:Select
+/-/PU/PD:Value
F5:Previous Values
F10:Save
ESC:Exit
F6:Fail-Safe Defaults
F1:General Help
F7:Optimized Defaults
Figure 6: PnP/PCI Configurations
PNP OS Installed
Yes
Select Yes if you are using a Plug and Play capable operating system.
(Default value)
No
Select No if you need the BIOS to configure non-boot devices.
PCI 1/PCI 5 IRQ Assignment
Auto
Auto assign IRQ to PCI 1/PCI 5. (Default value)
3,4,5,7,9,10,11,12,14,15
Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 1/PCI 5.
PCI 2 IRQ Assignment
Auto
Auto assign IRQ to PCI 2. (Default value)
3,4,5,7,9,10,11,12,14,15 Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 2.
PCI 3 IRQ Assignment
Auto
Auto assign IRQ to PCI 3. (Default value)
3,4,5,7,9,10,11,12,14,15
Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 3.
PCI 4 IRQ Assignment
Auto
Auto assign IRQ to PCI 4. (Default value)
3,4,5,7,9,10,11,12,14,15
Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 4.
GA-7VASFS-FS Motherboard
- 44 -
English
PC Health Status
CMOS Setup Utility-Copyright (C) 1984-2003 Award Software
PC Health Status
Vcore
1.74V
Item Help
+3.3V
3.28V
Menu Level
+5V
5.107V
+12V
11.668V
5VSB
4.919V
Current System Temperature
32°C
Current CPU Temperature
40°C
Current CPU FAN Speed
6490 RPM
Current SYSTEM FAN Speed
0 RPM
Current POWER FAN Speed
0 RPM
: Move
Enter:Select
F5:Previous Values
+/-/PU/PD:Value
F10:Save
ESC:Exit
F6:Fail-Safe Defaults
F1:General Help
F7:Optimized Defaults
Figure 7: PC Health Status
Current Voltage (V) Vcore / +3.3V / +5V / +12V /5VSB
Detect system's voltage status automatically.
Current System/CPU Temperature
Detect System/CPU Temp. automatically.
Current CPU/SYSTEM/POWER FAN Speed (RPM)
Detect CPU/SYSTEM/POWER Fan speed status automatically.
- 45 -
BIOS Setup
English
Frequency/Voltage Control
CMOS Setup Utility-Copyright (C) 1984-2003 Award Software
Frequency/Voltage Control
DRAM Clock (MHz)
[Auto]
Item Help
Menu Level
: Move
Enter:Select
+/-/PU/PD:Value
F5:Previous Values
F10:Save
ESC:Exit
F6:Fail-Safe Defaults
F1:General Help
F7:Optimized Defaults
Figure 8: Frequency/Voltage Control
DRAM Clock (MHz)
Please set DRAM Clock according to your requirement.
If you use DDR266 DRAM module, please set "DRAM Clock(MHz)" to Auto or 266. If you use
DDR333 DRAM module, please set "DRAM Clock(MHz)" to Auto or 333.
Incorrect using it may cause your system broken. For power End-User use only!
GA-7VASFS-FS Motherboard
- 46 -
English
Load Fail-Safe Defaults
CMOS Setup Utility-Copyright (C) 1984-2003 Award Software
Standard CMOS Features
Load Fail-Safe Defaults
Advanced BIOS Features
Load Optimized Defaults
Integrated Peripherals
Set Supervisor Password
Power Management Setup
Set User Password
PnP/PCI Configurations
Save & Exit Setup
PC Health Status
Load Fail-Safe Defaults?
Exit(Y/N)?Y
Without Saving
Frequency/Voltage Control
ESC:Quit
F8: Q-Flash
:Select Item
F10:Save & Exit Setup
Load Fail-Safe Defaults
Figure 9: Load Fail-Safe Defaults
Load Fail-Safe Defaults
Fail-Safe defaults contain the most appropriate values of the system parameters that allow
minimum system performance.
- 47 -
BIOS Setup
English
Load Optimized Defaults
CMOS Setup Utility-Copyright (C) 1984-2003 Award Software
Standard CMOS Features
Load Fail-Safe Defaults
Advanced BIOS Features
Load Optimized Defaults
Integrated Peripherals
Set Supervisor Password
Power Management Setup
Set User Password
PnP/PCI Configurations
Save & Exit Setup
PC Health Status
Exit Without Saving
Load Optimized Defaults?
(Y/N)?Y
Frequency/Voltage Control
ESC:Quit
:Select Item
F8: Q-Flash
F10:Save & Exit Setup
Load Optimized Defaults
Figure 10: Load Optimized Defaults
Load Optimized Defaults
Selecting this field loads the factory defaults for BIOS and Chipset Features which the
system automatically detects.
GA-7VASFS-FS Motherboard
- 48 -
English
Set Supervisor/User Password
CMOS Setup Utility-Copyright (C) 1984-2003 Award Software
Standard CMOS Features
Load Fail-Safe Defaults
Advanced BIOS Features
Load Optimized Defaults
Integrated Peripherals
Set Supervisor Password
Power Management Setup
Set User Password
PnP/PCI Configurations
Save & Exit Setup
PC Health Status
Exit Without Saving
Enter Password:
Frequency/Voltage Control
ESC:Quit
F8: Q-Flash
:Select Item
F10:Save & Exit Setup
Change/Set/Disable Password
Figure 11: Password Setting
When you select this function, the following message will appear at the center of the screen to assist
you in creating a password.
Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the
password. Type the password again and press <Enter>. You may also press <Esc> to abort the
selection and not enter a password.
To disable password, just press <Enter> when you are prompted to enter password. A message
"PASSWORD DISABLED" will appear to confirm the password being disabled. Once the password is
disabled, the system will boot and you can enter Setup freely.
The BIOS Setup program allows you to specify two separate passwords:
SUPERVISOR PASSWORD and a USER PASSWORD. When disabled, anyone may access
all BIOS Setup program function. When enabled, the Supervisor password is required for entering the
BIOS Setup program and having full configuration fields, the User password is required to access only
basic items.
If you select "System" at "Password Check" in Advance BIOS Features Menu, you will be
prompted for the password every time the system is rebooted or any time you try to enter Setup Menu.
If you select "Setup" at "Password Check" in Advance BIOS Features Menu, you will be prompted
only when you try to enter Setup.
- 49 -
BIOS Setup
English
Save & Exit Setup
CMOS Setup Utility-Copyright (C) 1984-2003 Award Software
Standard CMOS Features
Load Fail-Safe Defaults
Advanced BIOS Features
Load Optimized Defaults
Integrated Peripherals
Set Supervisor Password
Power Management Setup
Set User Password
PnP/PCI Configurations
& Exit
Save to CMOS and EXITSave
(Y/N)?
Y Setup
PC Health Status
Exit Without Saving
Frequency/Voltage Control
ESC:Quit
:Select Item
F8: Q-Flash
F10:Save & Exit Setup
Save Data to CMOS
Figure 12: Save & Exit Setup
Type "Y" will quit the Setup Utility and save the user setup value to RTC CMOS.
Type "N" will return to Setup Utility.
GA-7VASFS-FS Motherboard
- 50 -
English
Exit Without Saving
CMOS Setup Utility-Copyright (C) 1984-2003 Award Software
Standard CMOS Features
Load Fail-Safe Defaults
Advanced BIOS Features
Load Optimized Defaults
Integrated Peripherals
Set Supervisor Password
Power Management Setup
Set User Password
PnP/PCI Configurations
Save & Exit Setup
PC Health Status
Exit Without Saving
Quit Without Saving (Y/N)? N
Frequency/Voltage Control
ESC:Quit
F8: Q-Flash
:Select Item
F10:Save & Exit Setup
Abandon all Data
Figure 13: Exit Without Saving
Type "Y" will quit the Setup Utility without saving to RTC CMOS.
Type "N" will return to Setup Utility.
- 51 -
BIOS Setup
English
GA-7VASFS-FS Motherboard
- 52 -