Black & Decker FSM1610 Technical data

FSM1610
FSM1620
A
B
C
D
E
2
F
G
H
I
3
ENGLISH
(Original instructions)
Intended use
Your Black & Decker steam mop has been designed for
sanitising and cleaning sealed hardwood, sealed laminate,
linoleum, vinyl, ceramic tile, stone and marble floors and for
refreshing carpets. This appliance is intended for indoor
household use only.
Warning! Read all of the 'Safety, Maintenance,
Service' manual carefully before operating
this appliance.
Read all of this manual carefully before operating
the appliance.
Attaching a cleaning pad (Fig. D)
Replacement cleaning pads are available from your Black &
Decker dealer:- (cat. no. FSMP20-XJ).
u Place a cleaning pad (6) on the floor with the ‘hook & loop’
side facing up.
u Lightly press the steam mop down onto the cleaning pad
(6).
Caution! Always place your steam mop on the resting mat (7)
with the handle (4) in the upright position when stationary and
make sure the steam mop is turned off when not in use.
Removing a cleaning pad (Fig. E)
This appliance includes some or all of the following features.
1. ON/Off switch
2. AutoselectTM dial
3. Removable water tank
4. Handle
5. Steam head
6. Steam head cleaning pad
7. Resting mat
8. Bottom cable tidy hook
9. Top cable tidy hook
10. Cable management clip
Caution! Always wear suitable shoes when changing the
cleaning pad on your steam mop. Do not wear slippers or
open toed footwear.
u Return the handle (4) to the upright position and turn the
steam mop ‘OFF’.
u Place the steam mop on the resting mat and wait until it
cools down. (approximately five minutes)
u Place the front of your shoe onto the cleaning pad removal
tab (14) and press down firmly.
u Lift the steam mop up off the cleaning pad.
Caution! Always place the steam mop on the resting mat (7)
with the handle (4) in the upright position when stationary and
make sure the steam mop is turned off when not in use.
Assembly
Filling the water tank (Fig. F)
Features
Warning! Before attempting any of the following operations,
make sure that the appliance is switched off and unplugged
and that the appliance is cold and does not contain any water.
Attaching the handle (Fig. A)
u
Slide the bottom end of the handle (4) into the top end
of the steam mop body (12) until it clicks into place. The
arrow on the handle (4) should be aligned with the top of
the steam mop body (12).
Attaching the steam head (Fig. B)
Slide the bottom end of the steam mop body (12) onto the
steam head (5) until it clicks into place.
u The steam head can be removed from the Steam mop
body by pressing the steam head release button (13) and
pulling the steam mop body (12) off the steam head (5).
u
Attaching the water jug (Fig. C)
Clip the water jug (3) onto the handle (4).
u Slide the water jug (3) down into the Steam mop body
(12), ensure that the water jug is firmly seated.
u
4
The water tank on your steam mop is removable for convenient and easy filling.
This Steam Mop incorporates an anti-calc system to help
prolong the life of the system.
Note: Fill the water tank with clean tap water.
Note: In areas of very hard water, the use of de-ionised water
is recommended.
u Remove the water tank (3).
u Open the filler cap (16) by lifting it up.
u Fill the water tank (3) with water.
Warning! Your water tank has a 460 ml capacity. Do not over
fill the tank.
u Re-fit the filler cap (16).
u Re-fit the water tank (3).
Note: Ensure the filler cap is firmly secured.
Note: Do not use chemical cleaners with your steam mop..
Attaching the carpet glider (Fig. G) (FSM1620 Only)
Place carpet glider on the floor.
Attach a cleaning pad to the unit.
u Lightly press the steam mop down onto the carpet glider
(11) until it clicks into place.
Caution! Always place the steam mop on the resting mat (7)
with the handle (4) in the upright position when stationary and
make sure the steam mop is turned off when not in use.
u
u
(Original instructions)
Removing the carpet glider (Fig. G) (FSM1620 Only)
Caution! Always wear suitable shoes when changing the
carpet glider on your steam mop. Do not wear slippers or
open toed footwear.
u Return the handle (4) to the upright position and turn the
steam mop ‘OFF’.
u Place the steam mop on the resting mat and wait until it
cools down. (approximately five minutes)
u Place the front of your shoe onto the carpet glider removal
tab (15) and press down firmly.
u Lift the steam mop up off the carpet glider (11).
Caution! Always place the steam mop on the resting mat (7)
with the handle (4) in the upright position when stationary and
make sure the steam mop is turned off when not in use.
Use
Important! This unit will kill 99.9% of bacteria & germs when
used in accordance with this manual and with the micro fibre
pad fitted and a continuous run time of 90 seconds.
Switching on and off
To switch the appliance on, press the ON/OFF button (1).
It takes approximately 15 seconds for the steam mop to
heat up.
Note: When the steam mop is first turned on the water reservoir will glow red. Once the steam mop is ready to use the
water reservoir will glow blue.
u To switch the appliance off, press the ON/OFF button (1).
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop on
the resting mat (7) with the handle (4) in the upright position
when stationary and make sure the steam mop is turned off
when not in use.
Caution! Always empty the steam mop after use.
Note: When first filled or after running dry it can take up to 45
seconds for steam to be produced.
u
AutoselectTM Technology
This steam mop is fitted with an AutoselectTM dial (2) which
shows various cleaning applications. They are used to select
the correct operating mode for your particular cleaning operation.
Using the AutoselectTM dial (2), choose from one of the following applications:
Wood/Laminate
Stone/Marble
Tiles/Vinyl
ENGLISH
The steam mop will select the correct volume of steam
required for your particular cleaning operation.
Note: Always check you are using the correct setting before
using your steam mop.
Hints for optimum use
General
Caution! Never use the steam mop without first attaching a
cleaning pad.
u During use you can use the cable management clip (10) to
keep your cable out of the way of the work area..
u Always vacuum or sweep the floor before using the steam
mop.
u The easiest way to use the machine is to tilt the handle to
a 45˚ angle and clean slowly, covering a small area at a
time.
u Do not use chemical cleaners with your steam mop. To
remove stubborn stains from vinyl or linoleum floors, you
can pre-treat with a mild detergent and some water before
using the steam mop.
Steam cleaning
u Place a cleaning pad (6) on the floor with the ‘hook & loop’
side facing up.
u Raise the steam mop off the resting mat (7) and lightly
press it down onto the cleaning pad (6).
u Place the steam mop on the resting mat.
u Connect the steam mop to the mains.
TM
u Turn the Autoselect dial (2) to the required setting.
u Press the ON/OFF button (1). It takes approximately 15
seconds for the steam mop to heat up.
u Pulling the handle (4) back will activate the steam pump.
After a few seconds steam will start to come out of the
steam head.
Note: When first filled or after running dry it can take up to 45
seconds for steam to be produced.
u It takes a few seconds for steam to enter the cleaning pad.
The steam mop will now glide easily over the surface to be
sanitised/cleaned.
u Push and pull the steam mop slowly across the floor to
thoroughly steam clean each section.
Note: During use you may turn off the steam pump by returning the handle to the upright position, this convenient feature
will allow you to place the steam mop on the resting mat for
a short time so that you may move items of furniture, then
continue cleaning without the need to switch the appliance off.
u When you have finished using the steam mop, return the
handle (4) to the upright position and turn it ‘OFF’, place it
on the resting mat (7) and wait until the steam mop cools
down. (approximately five minutes)
5
ENGLISH
(Original instructions)
Caution! It is important to monitor the water level in the water
tank. To refill the water tank and continue to sanitise/clean,
return the handle (4) to the upright position and turn the steam
mop ‘OFF’. Unplug the unit from the electrical wall outlet,
remove and refill the water tank (3).
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop on
the resting mat (7) with the handle (4) in the upright position
when stationary and make sure the steam mop is turned off
when not in use.
Carpet refreshing (FSM1620 only)
u Place a cleaning pad (6) on the floor with the ‘hook & loop’
side facing up.
u Raise the steam mop off the resting mat (7) and lightly
press it down onto the cleaning pad (6).
u Place the carpet glider (11) on the floor.
u Lightly press the steam mop down onto the carpet glider
(11) until it clicks into place.
u Place the steam mop on the resting mat. (7)
u Connect the steam mop to the mains.
u Press the ON/OFF button (1). It takes approximately 15
seconds for the steam mop to heat up.
TM
u Turn the Autoselect dial (2) to the Wood/Laminate setting.
u Pulling the handle (4) back will activate the steam pump.
After a few seconds steam will start to come out of the
steam head.
Note: When first filled or after running dry it can take up to 45
seconds for steam to be produced.
u Push and pull the steam mop slowly across the carpet to
thoroughly refresh each section.
Note: During use you may turn off the steam pump by returning the handle (4) to the upright position, this convenient
feature will allow you to place the steam mop on the resting
mat (7) so that you may move items of furniture with out the
need to switch the appliance off.
u When you have finished using the steam mop, return the
handle (4) to the upright position and turn it ‘OFF’, place it
on the resting mat (7) and wait until the steam mop cools
down. (approximately five minutes)
Caution! It is important to monitor the water level in the water
tank. To refill the water tank and continue to sanitise/clean,
return the handle (4) to the upright position and turn the steam
mop ‘OFF’. Unplug the unit from the electrical wall outlet,
remove and refill the water tank (3).
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop on
the resting mat (7) with the handle (4) in the upright position
when stationary and make sure the steam mop is turned off
when not in use.
6
After use (Fig. H & I)
u Return the handle (4) to the upright position and turn the
steam mop ‘OFF’,
u Place the steam mop on the resting mat (7) and wait until
the steam mop cools down. (approximately five minutes)
u Unplug the steam mop from the electrical wall outlet.
u Empty the water tank (3).
u Remove the cleaning pad (6) and wash it ready for next
use. (Take care to follow the wash care instructions
printed on the cleaning pad).
u Wrap the supply cable around the cable tidy hooks (8 &
9).
Note: The top cable tidy hook (9) rotates to easily release the
cable ready for next use.
u Clip the supply cable onto itself using the cable tidy clip
(17) close to the plug.
u Place steam mop on the resting mat (7) for storage.
Note: With the handle (4) in the upright position, the cable
neatly wrapped around the cable tidy hooks (8 & 9) and
secured with the cable tidy clip (17) your steam mop will stand
on its own for storage. Alternatively there is a hanging bracket
(18) built into the hand grip (19) which will allow your steam
mop to be hung from a suitable hook on the wall. Always
ensure that your wall hook is capable of supporting the weight
of the steam mop safely.
Technical data
Voltage
Vac
Power
W
Tank capacity
ml
Weight
kg
FSM1610
FSM1620
(Type 1)
(Type 1)
230
230
1600
1600
460
460
2.7
3.06
(Original instructions)
ENGLISH
Troubleshooting
If your appliance seems not to operate properly, follow the
instructions below. If this does not solve the problem, please
contact your local Black & Decker repair agent.
Problem
Step
Possible solutions
The steam mop is
1
Check the unit is plugged in at the wall
socket.
not turning on.
2
Check the unit is switched on using the on/
off switch (1).
The steam mop is
3
Check the fuse in the plug.
4
The steam mop will only produce steam
not producing
once the handle is pulled back from the
steam.
upright position.
5
Check that the water tank (3) is full and
correctly fitted.
NOTE: When first filled or after running dry it
can take up to 45 seconds for steam to be
produced.
6
Check that the Steam head (5) is firmly
docked into the steam mop body (12).
The steam mop
7
Check steps 1, then 2 then 3.
8
Check steps 4, then 5, then 6 and then 3.
9
The steam mop has 3 settings. Turn the
stops producing
steam during use.
The steam mop is
producing too
autoselect dial (2) to increase the amount of
much steam during
steam being produced.
use.
The steam mop is
producing too little
steam during use.
10
Check step 5.
11
The steam mop has 3 settings. Turn the
autoselect dial (2) to reduce the amount of
steam being produced.
Steam is escaping
12
Refer to the assembly chapter of the manual
from unexpected
for correct fitting instructions of all parts and
areas of the unit.
accessories.
Where can I get
further information
13
www.blackanddecker.co.uk/steammop
www.blackanddecker.ie/steammop
/ accessories for
my steam mop.
7
TYPE
FSM1610 - FSM1620
1
4
1
5
2
6
7
3
8
15
25
10
11
12
14
9
16
E16760
www.2helpU.com
17
20 - 09 - 12
9
10
ENGLISH
Do not forget to register your product!
www.blackanddecker.co.uk/productregistration
Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product
code to Black & Decker in your country.
Australia
Black & Decker (Australia) Pty. Ltd.
20 Fletcher Road, Mooroolbark, Victoria, 3138
New Zealand
Black & Decker
5 Te Apunga Place
Mt Wellington
Auckland 1060
United Kingdom
Black & Decker
210 Bath Road
Slough, Berkshire SL1 3YD
90598588 REV-0
Tel. 03-8720 5100
Fax 03-9727 5940
Tel. +64 9 259 1133
Fax +64 9 259 1122
Tel. 01753 511234
Fax 01753 551155
05/2013