Renesas SH7210 Series User`s manual

REJ10J1317-0101
SH7211 Group FP-144L
User System Interface Board
User’s Manual
Renesas Microcomputer Development Environment System
SuperH™ Family / SH7210 Series
R0E572110CFK00
Rev.1.01
Revision Date: Aug. 08, 2006
Keep safety first in your circuit designs!
1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and
more reliable, but there is always the possibility that trouble may occur with them. Trouble with
semiconductors may lead to personal injury, fire or property damage.
Remember to give due consideration to safety when making your circuit designs, with appropriate
measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or
(iii) prevention against any malfunction or mishap.
Notes regarding these materials
1. These materials are intended as a reference to assist our customers in the selection of the Renesas
Technology Corp. product best suited to the customer's application; they do not convey any license
under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or
a third party.
2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any thirdparty's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or
circuit application examples contained in these materials.
3. All information contained in these materials, including product data, diagrams, charts, programs and
algorithms represents information on products at the time of publication of these materials, and are
subject to change by Renesas Technology Corp. without notice due to product improvements or
other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or
an authorized Renesas Technology Corp. product distributor for the latest product information
before purchasing a product listed herein.
The information described here may contain technical inaccuracies or typographical errors.
Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising
from these inaccuracies or errors.
Please also pay attention to information published by Renesas Technology Corp. by various means,
including the Renesas Technology Corp. Semiconductor home page (http://www.renesas.com).
4. When using any or all of the information contained in these materials, including product data,
diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total
system before making a final decision on the applicability of the information and products. Renesas
Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the
information contained herein.
5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or
system that is used under circumstances in which human life is potentially at stake. Please contact
Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when
considering the use of a product contained herein for any specific purposes, such as apparatus or
systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use.
6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in
whole or in part these materials.
7. If these products or technologies are subject to the Japanese export control restrictions, they must
be exported under a license from the Japanese government and cannot be imported into a country
other than the approved destination.
Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the
country of destination is prohibited.
8. Please contact Renesas Technology Corp. for further details on these materials or the products
contained therein.
IMPORTANT INFORMATION
READ FIRST
• READ this user's manual before using this emulator product.
• KEEP the user's manual handy for future reference.
Do not attempt to use the emulator product until you fully understand its mechanism.
Emulator Product:
Throughout this document, the term "emulator product" shall be defined as the following
products produced only by Renesas Technology Corp. and Renesas Solutions Corp. excluding all
subsidiary products.
•
•
•
•
•
•
•
E200F main unit
External bus trace unit
EV-chip unit
Expansion profiling unit
Emulation memory unit
User system interface board
Trace cable
The user system or a host computer is not included in this definition.
Purpose of the User System Interface Board:
The user system interface board is used to connect the evaluation chip unit to the user system.
This user system interface board must only be used for the above purpose.
Limited Applications:
This emulator product is not authorized for use in transportation, vehicular, medical (where
human life is potentially at stake), aerospace, nuclear, or undersea repeater applications. Buyers of
this emulator product must notify Renesas Technology Corporation, Renesas Solutions
Corporation or an authorized Renesas Technology product distributor before planning to use the
product in such applications.
Improvement Policy:
Renesas Technology Corp. (including its subsidiaries, hereafter collectively referred to as
Renesas) pursues a policy of continuing improvement in design, performance, and safety of the
emulator product. Renesas reserves the right to change, wholly or partially, the specifications,
design, user's manual, and other documentation at any time without notice.
I
Target User of the Emulator Product:
This emulator product should only be used by those who have carefully read and thoroughly
understood the information and restrictions contained in the user's manual. Do not attempt to use
the emulator product until you fully understand its mechanism.
It is highly recommended that first-time users be instructed by users that are well versed in the
operation of the emulator product.
Users are required to be familiar with the basic knowledge for the electric circuits, logic
circuits, and microcomputers.
Precautions to be Taken when Using This Product:
1. This emulator is a development supporting unit for use in your program development and
evaluation stages. In mass-producing your program you have finished developing, be sure to
make a judgment on your own risk that it can be put to practical use by performing integration
test, evaluation, or some experiment else.
2. In no event shall Renesas Solutions Corporation be liable for any consequence arising from the
use of this emulator.
3. Renesas Solutions Corporation strives to renovate or provide a workaround for product
malfunction at some charge or without charge. However, this does not necessarily mean that
Renesas Solutions Corporation guarantees the renovation or the provision under any
circumstances.
4. This emulator has been developed by assuming its use for program development and
evaluation in laboratories. Therefore, it does not fall under the application of Electrical
Appliance and Material Safety Law and protection against electromagnetic interference when
used in Japan.
5. This emulator does not conform to safety standards such as UL or IEC. Be careful when you
take this emulator overseas.
6. Renesas cannot anticipate every possible circumstance that might involve a potential hazard.
The warnings in this user's manual and on the emulator product are therefore not all inclusive.
Therefore, you must use the emulator product safely at your own risk.
II
LIMITED WARRANTY
Renesas warrants its emulator products to be manufactured in
accordance with published specifications and free from defects in
material and/or workmanship. Renesas, at its option, will replace any
emulator products returned intact to the factory, transportation charges
prepaid, which Renesas, upon inspection, shall determine to be defective
in material and/or workmanship. The foregoing shall constitute the sole
remedy for any breach of Renesas’ warranty. See the Renesas warranty
booklet for details on the warranty period. This warranty extends only
to you, the original Purchaser. It is not transferable to anyone who
subsequently purchases the emulator product from you. Renesas is not
liable for any claim made by a third party or made by you for a third
party.
DISCLAIMER
RENESAS MAKES NO WARRANTIES, EITHER EXPRESS OR
IMPLIED, ORAL OR WRITTEN, EXCEPT AS PROVIDED
HEREIN, INCLUDING WITHOUT LIMITATION THEREOF,
WARRANTIES AS TO MARKETABILITY, MERCHANTABILITY,
FITNESS FOR ANY PARTICULAR PURPOSE OR USE, OR
AGAINST INFRINGEMENT OF ANY PATENT. IN NO EVENT
SHALL RENESAS BE LIABLE FOR ANY DIRECT, INCIDENTAL
OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR
LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE
EMULATOR PRODUCT, THE USE OF ANY EMULATOR
PRODUCT, OR ITS DOCUMENTATION, EVEN IF ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES. EXCEPT AS
EXPRESSLY STATED OTHERWISE IN THIS WARRANTY,
THIS EMULATOR PRODUCT IS SOLD "AS IS ", AND YOU
MUST ASSUME ALL RISK FOR THE USE AND RESULTS
OBTAINED FROM THE EMULATOR PRODUCT.
III
State Law:
Some states do not allow the exclusion or limitation of implied warranties or liability for
incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which may vary from
state to state.
The Warranty is Void in the Following Cases:
Renesas shall have no liability or legal responsibility for any problems caused by misuse,
abuse, misapplication, neglect, improper handling, installation, repair or modifications of the
emulator product without Renesas’ prior written consent or any problems caused by the user
system.
All Rights Reserved:
1. Circuitry and other examples described herein are meant merely to indicate the characteristics
and performance of Renesas’ semiconductor products. Renesas assumes no responsibility for
any intellectual property claims or other problems that may result from applications based on
the examples described herein.
2. No license is granted by implication or otherwise under any patents or other rights of any third
party or Renesas.
3. This user's manual and emulator product are copyrighted and all rights are reserved by
Renesas. No part of this user's manual, all or part, may be reproduced or duplicated in any
form, in hard-copy or machine-readable form, by any means available without Renesas’ prior
written consent.
Figures:
Some figures in this user's manual may show items different from your actual system.
IV
SAFETY PAGE
READ FIRST
• READ this user's manual before using this emulator product.
• KEEP the user's manual handy for future reference.
Do not attempt to use the emulator product until you fully understand its mechanism.
DEFINITION OF SIGNAL WORDS
Either in the user's manual or on the product, several icons are used to insure proper
handling of this product and also to prevent injuries to you or other persons, or damage to
your properties. Their graphic images and meanings are given in this safety page. Be sure to
read this chapter before using the product.
This is the safety alert symbol. It is used to alert you to potential personal
injury hazards. Obey all safety messages that follow this symbol to avoid
possible injury or death.
DANGER
WARNING
CAUTION
CAUTION
DANGER indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
CAUTION used without the safety alert symbol indicates a
potentially hazardous situation which, if not avoided, may result
in property damage.
NOTE emphasizes essential information.
In addition to the four above, the following are also used as appropriate.
V
means WARNING or CAUTION.
Example:
CAUTION AGAINST AN ELECTRIC SHOCK
means PROHIBITION.
Example:
DISASSEMBLY PROHIBITED
means A FORCIBLE ACTION.
Example:
VI
UNPLUG THE POWER CABLE FROM THE RECEPTACLE.
WARNING
Warnings for AC Power Supply:
• If
the attached AC power cable does not fit the
receptacle, do not alter the AC power cable and do not
plug it forcibly. Failure to comply may cause electric
shock and/or fire.
• Use
an AC power cable which complies with the safety
standard of the country.
• Do
not touch the plug of the AC power cable when your
hands are wet. This may cause electric shock.
• This
product is connected signal ground with frame
ground. If your developing product is transformless (not
having isolation transformer of AC power), this may cause
electric shock. Also, this may give an unrepairable
damage to this product and your developing one.
While developing, connect AC power of the product to
commercial power through isolation transformer in order
to avoid these dangers.
• If
other equipment is connected to the same branch
circuit care should be taken not to overload the circuit.
Refer to nameplate for electrical ratings.
•
When installing this equipment, insure that a reliable
ground connection is maintained.
VII
WARNING
• If
you smell a strange odor, hear an unusual sound, or
see smoke coming from this product, then disconnect
power immediately by unplugging the AC power cable
from the outlet.
Do not use this as it is because of the danger of electric
shock and/or fire. In this case, contact your local
distributor.
• When
installing or connecting this product with other
equipment, shut down AC power or disconnect the AC
power cord from the equipment to prevent personal injury
or damage to the equipment.
Warnings to Be Taken for This Product:
•
Do not disassemble or modify this product. Personal
injury due to electric shock may occur if this product is
disassembled and modified.
•
Make sure nothing falls into the cooling fan on the top
panel, especially liquids, metal objects, or anything
combustible.
Warning for Installation:
•
Do not set this product in water or areas of high
humidity. Make sure that the product does not get wet.
Spilling water or some other liquid into the product may
cause unrepairable damage.
Warning for Use Environment:
• This equipment is to be used in an environment with a
maximum ambient temperature of 35°C. Care should be
taken that this temperature is not exceeded.
VIII
CAUTION
Cautions for AC Adapter:
• Use only the AC adapter included in this product
package.
•
The included AC adapter is for this emulator. Do not use it
for other product.
•
The DC plug on the included AC adapter has the below
polarity.
•
The included AC adapter has no power supply switch.
The AC adapter is always active while connecting the AC
power cable. Check if the power is supplied by the LED of
AC adapter.
Cautions to Be Taken for This Product:
•
Use caution when handling this product. Be careful not to
apply a mechanical shock.
•
Do not pull the main unit by the probe of the emulation
probe or the flexible cable which are connected to this
product. Excessive flexing or force of the flexible cable for
connecting this product to the emulation probe may break
connector.
Caution for Installation:
•
When in use do not place the emulator on its side.
IX
WARNING
Observe the precautions listed below. Failure to do so
will result in a FIRE HAZARD and will damage the user
system and the emulator product or will result in
PERSONAL INJURY. The USER PROGRAM will be
LOST.
1. Do not repair or remodel the emulator product by
yourself for electric shock prevention and quality
assurance.
2. Always switch OFF the E200F emulator and user system
before connecting or disconnecting any CABLES or
PARTS.
3. Always before connecting any CABLES, make sure that
pin 1 on both sides are correctly aligned.
X
Preface
The R0E572110CFK00 is a user system interface board that connects a user system for the
SH7211 FP-144L package to the SH7211 E200F emulator (R0E0200F1EMU00 or
R0E572110VKK00).
i
Contents
Section 1 Configuration.....................................................................................1
Section 2 Environmental Conditions.................................................................3
Section 3 Connection Procedures ......................................................................4
3.1
3.2
3.3
3.4
3.5
Connecting User System Interface Board to User System................................................ 4
3.1.1 Installing IC Socket ............................................................................................. 4
3.1.2 Installing Cable Head........................................................................................... 5
3.1.3 Fastening Cable Head .......................................................................................... 5
Connecting User System Interface Board to EV-Chip Unit ............................................. 7
Recommended Dimensions for User System Mount Pad (Footprint)............................... 9
Dimensions for External Bus Trace Unit, EV-Chip Unit, and User System
Interface Board ................................................................................................................. 11
Resulting Dimensions after Connecting User System Interface Board ............................ 12
Section 4 Installing the MPU to the User System .............................................15
Section 5 Verifying Operation...........................................................................17
Section 6 Notice ................................................................................................18
ii
Section 1 Configuration
Figure 1 and table 1 show the configuration and components of the user system interface board for
the FP-144L package. Please make sure you have all of these components when unpacking.
Screws (M2.0 x 6 mm)
External bus trace unit
EV-chip unit
Screws (M2.0 x 10 mm)
Board
Socket cover
Spacer
IC socket
User system
Figure 1 User System Interface Board for the SH7211 FP-144L Package
1
CAUTION
Use a NQPACK144SD socket (manufactured by Tokyo
Eletech Corporation) for the FP-144L package IC socket on
the user system.
Table 1
R0E572110CFK00 Components
No. Component
Quantity
Remarks
1
Board
1
With four spacers (2.6MP x 11 mm)
2
IC socket
1
For the FP-144L package (to be mounted on the
user system)
3
Socket cover
1
For the FP-144L package (for installing MPU)
4
Screws (M2.0 x 10 mm)
4
For fastening board
5
Screws (M2.0 x 6 mm)
4
For installing an FP-144L-packaged MPU
6
Guide pins
3
7
Screwdriver
1
8
User’s manual
1
2
User’s manual for R0E572110CFK00 (this
manual)
Section 2 Environmental Conditions
Maintain the conditions in table 2 when using the emulator.
Table 2
Environmental Conditions
Item
Specifications
Temperature
Operating: +10 to +35°C
Storage: -10 to +35°C
Humidity
Operating: 35 to 80% RH, no condensation
Storage: 35 to 80% RH, no condensation
Vibration
Operating: 2.45 m/s max.
2
Storage: 4.9 m/s max.
2
Transportation: 14.7 m/s max.
Ambient gases
There must be no corrosive gases present.
2
3
Section 3 Connection Procedures
3.1
Connecting User System Interface Board to User System
WARNING
Always switch OFF the user system and the emulator
product before the USER SYSTEM INTERFACE BOARD
is connected to or removed from any part. Before
connecting, make sure that pin 1 on both sides are correctly
aligned. Failure to do so will result in a FIRE HAZARD and
will damage the user system and the emulator product or
will result in PERSONAL INJURY. The USER PROGRAM will
be LOST.
To connect the cable head to the user system, follow the instructions below.
3.1.1
Installing IC Socket
Solder the IC socket for an FP-144L package to the user system.
CAUTION
Be sure to completely solder the leads so that the solder
slops gently over the leads and forms solder fillets. (Use
slightly more solder than the MPU.)
4
3.1.2
Installing Cable Head
CAUTION
Check the location of pin 1 before inserting.
Align pin 1 on the IC socket for an FP-144L package on the user system with pin 1 on the user
system interface board, and insert the user system interface board into the IC socket on the user
system, as shown in figure 2.
3.1.3
Fastening Cable Head
CAUTION
1. Use a Phillip-type screwdriver whose head matches the
screw head.
2. The tightening torque must be 0.054 N•m or less.
If the applied torque cannot be accurately measured,
stop tightening when the force required to turn the screw
becomes significantly greater than that needed when first
tightening. If a screw is tightened too much, the screw
head may break or an IC socket contact error may be
caused by a crack in the IC socket solder.
3. If the emulator does not operate correctly, cracks might
have occurred in the solder. Check conduction with
a tester and re-solder the IC socket if necessary.
Fasten the user system interface board to the IC socket for an FP-144L package on the user system
with the four screws (M2.0 x 10 mm) provided. Each screw should be tightened a little at a time,
alternating between screws on opposing corners. Take special care, such as manually securing the
IC socket soldered area, to prevent the soldered IC socket from being damaged by overtightening
the screws or twisting the components.
5
Screws (M2.0 x 10 mm)
Board
Pin 1
User system
IC socket
(NQPACK144SD manufactured by
Tokyo Eletech Corporation)
Figure 2 Connecting User System Interface Board to User System
6
3.2
Connecting User System Interface Board to EV-Chip Unit
WARNING
Observe the precautions listed below. Failure to do so
will result in a FIRE HAZARD and will damage the user
system and the emulator product or will result in
PERSONAL INJURY. The USER PROGRAM will be
LOST.
1. Always switch OFF the user system and the emulator
product before the USER SYSTEM INTERFACE BOARD
is connected to or removed from any part. Before
connecting, make sure that pin 1 on both sides are
correctly aligned.
2. The user system interface board dedicated to the
emulator must be used.
1. Make sure the user system and emulator are turned off.
2. Align the connectors on the board with those on the EV-chip unit according to their numbers
(figure 3).
3. Adjust the height of the spacer attached to the board with the user system.
7
External bus trace unit
EV-chip unit
Connector No.
EV-Chip Unit
Connector No.
User I/F Connector 1
(CN3)
User I/F Connector 2
(CN4)
Board
Connector No.
UCN1
UCN2
Board
Spacer
Pin 1
User system
Figure 3 Connecting User System Interface Board to EV-Chip Unit
8
3.3
Recommended Dimensions for User System Mount Pad (Footprint)
Figure 4 shows the recommended dimensions for the mount pad (footprint) for the user system
with an IC socket for an FP-144L package (NQPACK144SD: manufactured by Tokyo Eletech
Corporation). Note that the dimensions in figure 4 are somewhat different from those of the
actual chip's mount pad.
9
23.00 min
19.00 max
0.50 × 35 = 17.50
0.50
Pin 1
0.25
7.0
0.50 × 35 = 17.5
0.5
7.0
φ1.0
Location determination hole
2.00
Dimension and tolerance
Tolerance
Dimension
±0.05
Up to 1.2
±0.10
1.3 to 2.0
±0.15
2.1 to 5.0
±0.20
5.1 to 10.0
10.1 or above ±0.30
Unit: mm
Figure 4 Recommended Dimensions for Mount Pad
10
3.4
Dimensions for External Bus Trace Unit, EV-Chip Unit, and User
System Interface Board
The dimensions for the external bus trace unit, EV-chip unit, and the user system interface board
are shown in figure 5.
90.0
125.0
External bus trace unit
110.0
90.0
20.0
125.0
EV-chip unit
60.0
45.0
30.0
90.0
Pin 1
5.0
Spacer
Board
Dimension and tolerance
Dimension
Tolerance
Up to 1.2
±0.05
1.3 to 2.0
±0.10
2.1 to 5.0
±0.15
5.1 to 10.0
±0.20
10.1 or above ±0.30
Unit: mm
5.0
Figure 5 Dimensions for External Bus Trace Unit, EV-Chip Unit, and User System
Interface Board
11
3.5
Resulting Dimensions after Connecting User System Interface Board
The resulting dimensions, after connecting the user system interface board to the user system, are
shown in figures 6, 7, and 8.
External bus trace unit
Optional memory unit
12.5
29.2
55.0
68.4
EV-chip unit
24.5
30.0
37.5
27.5
Spacer (φ6.0)
User system
IC socket
(NQPACK144SD manufactured by
Tokyo Eletech Corporation)
24.5
39.19
24.5
Pin 1
39.19
Dimension and tolerance
Dimension
Tolerance
Up to 1.2
±0.05
1.3 to 2.0
±0.10
2.1 to 5.0
±0.15
5.1 to 10.0
±0.20
10.1 or above
±0.30
Unit: mm
Top view
Figure 6 Resulting Dimensions after Connecting User System Interface Board (when
Connecting External Bus Trace Unit, Optional Memory Unit, and EV-Chip Unit)
12
12.5
29.2
55.5
42.1
External bus trace unit
EV-chip unit
24.5
37.5
27.5
30.0
Spacer (φ6.0)
User system
39.19
39.19
24.5
IC socket
(NQPACK144SD manufactured by
Tokyo Eletech Corporation)
24.5
Pin 1
Dimension and tolerance
Dimension
Tolerance
Up to 1.2
±0.05
1.3 to 2.0
±0.10
2.1 to 5.0
±0.15
5.1 to 10.0
±0.20
10.1 or above
±0.30
Unit: mm
Figure 7 Resulting Dimensions after Connecting User System Interface Board (when
Connecting External Bus Trace Unit and EV-Chip Unit)
13
12.5
29.2
42.6
EV-chip unit
24.5
37.5
27.5
30.0
Spacer (φ6.0)
User system
39.19
39.19
24.5
IC socket
(NQPACK144SD manufactured by
Tokyo Eletech Corporation)
24.5
Pin 1
Dimension and tolerance
Dimension
Tolerance
Up to 1.2
±0.05
1.3 to 2.0
±0.10
2.1 to 5.0
±0.15
5.1 to 10.0
±0.20
10.1 or above
±0.30
Unit: mm
Figure 8 Resulting Dimensions after Connecting User System Interface Board (when
Connecting EV-Chip Unit)
14
Section 4 Installing the MPU to the User System
CAUTION
1. Check the location of pin 1 before inserting.
2. Use a Philips-type screwdriver whose head matches the
screw head.
3. The tightening torque must be 0.054 N•m or less.
If the applied torque cannot be accurately measured,
stop tightening when the force required to turn the screw
becomes significantly greater than that needed when first
tightening. If a screw is tightened too much, the screw
head may break or an IC socket contact error may be
caused by a crack in the IC socket solder.
4. If the MPU does not operate correctly, cracks might have
occurred in the solder. Check conduction with a tester
and re-solder the IC socket if necessary.
Check the location of pin 1 before inserting the MPU into the IC socket on the user system, as
shown in figure 9. After inserting the MPU, fasten the socket cover with the provided four screws
(M2.0 x 6 mm). Take special care, such as manually securing the IC socket soldered area, to
prevent the IC socket from being damaged by overtightening the screws or twisting the
components.
15
Screws (M2.0 x 6 mm)
Socket cover
MPU (SH7211)
Pin 1
IC socket
(NQPACK144SD manufactured by
Tokyo Eletech Corporation)
User system
Figure 9 Installing MPU to User System
16
Section 5 Verifying Operation
1. Turn on the emulator according to the procedures described in the SH7211 E200F Emulator
User's Manual (R0E0200F1EMU00E or R0E572110VKK00E).
2. Verify the user system interface cable connections by checking the pin states with the
extended monitor and checking the bus states with the FILL command (emulator command).
If an error is detected, recheck the soldered IC socket and the location of pin 1.
3. The emulator connected to this user system interface board supports three kinds of clock
sources as the MPU clock. For details, refer to the SH7211 E200F Emulator User's Manual
(R0E0200F1EMU00E).
⎯ To use the emulator internal clock
Select the clock in the emulator by the CLOCK command (emulator command).
⎯ To use the external clock on the user system
Supply the external clock from the user system to the emulator by inputting the EXTAL
pin (pin 26) on the user system interface board or connecting the crystal oscillator to the
XTAL (pin 25) and EXTAL pins. For details, refer to the section of Clock Pulse Generator
in the SH7211 Group Hardware Manual.
Figure 10 shows the clock oscillator on the user system interface board.
1 MΩ
SU04
SU04
LVC125 22 Ω
To E200F
emulator
270 Ω
EXTAL XTAL
System clock
Figure 10 Clock Oscillator
17
Section 6 Notice
1.
Before connecting any parts or cables, make sure that pin 1 on the both sides are correctly
aligned.
2.
Do not apply excessive force to the user system interface board while it is connected to the
user system.
3.
The dimensions of the recommended mount pad for the IC socket for this user system
interface board are different from those of the MPU.
4.
This user system interface board is specifically designed for the SH7211 E200F EV-chip unit
(R0E572110VKK00). Do not use this board with any other emulator.
5. When power is not supplied to the Vcc pin on the user system interface board, the emulator
displays ** VCC DOWN. The emulator will not operate correctly.
18
SH7211 Group FP-144L
User System Interface Board
User's Manual
Publication Date: Rev.1.01, August 8, 2006
Published by:
Sales Strategic Planning Div.
Renesas Technology Corp.
Edited by:
Customer Support Department
Global Strategic Communication Div.
Renesas Solutions Corp.
© 2006. Renesas Technology Corp. All rights reserved. Printed in Japan.
Sales Strategic Planning Div.
Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
RENESAS SALES OFFICES
http://www.renesas.com
Refer to "http://www.renesas.com/en/network" for the latest and detailed information.
Renesas Technology America, Inc.
450 Holger Way, San Jose, CA 95134-1368, U.S.A
Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501
Renesas Technology Europe Limited
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K.
Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900
Renesas Technology (Shanghai) Co., Ltd.
Unit 204, 205, AZIACenter, No.1233 Lujiazui Ring Rd, Pudong District, Shanghai, China 200120
Tel: <86> (21) 5877-1818, Fax: <86> (21) 6887-7898
Renesas Technology Hong Kong Ltd.
7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong
Tel: <852> 2265-6688, Fax: <852> 2730-6071
Renesas Technology Taiwan Co., Ltd.
10th Floor, No.99, Fushing North Road, Taipei, Taiwan
Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999
Renesas Technology Singapore Pte. Ltd.
1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632
Tel: <65> 6213-0200, Fax: <65> 6278-8001
Renesas Technology Korea Co., Ltd.
Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea
Tel: <82> (2) 796-3115, Fax: <82> (2) 796-2145
Renesas Technology Malaysia Sdn. Bhd
Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jalan Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia
Tel: <603> 7955-9390, Fax: <603> 7955-9510
Colophon 6.0
SH7211 Group FP-144L
User System Interface Board
User’s Manual