DS STD-601A
Narrow band radio transceiver
STD-601400 MHz
The STD-601 400 MHz is a miniature transceiver designed for industrial applications. This module has selectable bands in a wide frequency
range in the region of 400 MHz, conforming to the ISM bands in various countries.
The STD-601 400 MHz has a simple serial interface and allows own communication protocol to be used. The RF Power, Data rate and
Channel can be set through the use of dedicated serial commands.
Features
・ Small 20 x 32 x 5 mm SMD
・ Selectable bands possible within wide frequency range.
- 429 / 434 / 447 / 458 MHz
・ Maximum RF Power 50 mW
・ Transparent interface for data input and output
Applications
・ Industrial remote control systems
・ Telemetry systems
MULTI
General
RF
Parameter
Specification
Communication form
One Way, Half Duplex
Emission class
F1D ( 2-GFSK )
Supply voltage
3.0 - 5.0 V
Guaranteed operating temp. range
-20 C to +65 C
Maximum operating temp. range
-30 C to +75 C
Frequency stability
+/- 3 ppm (-20 C to +65 C)
Dimensions
20 x 32 x 5 mm
Weight
4.5 g
Remark
Parameter
Specification
Remark
Frequency
(429 MHz band) 429.1750 - 429.7375 MHz
(47 ch)
(434 MHz band) 433.0750 - 434.7750 MHz
(137 ch)
(447 MHz band) 447.2750 - 447.9875 MHz
(59 ch)
(458 MHz band) 458.5000 - 459.1750 MHz
(28 ch)
Data rate
1200 / 2400 / 4800 / 9600 / 19200 bps
TX current consumption
35 mA typ.
RF 10 mW
58 mA typ.
RF 50 mW
RX current consumption
19 mA
Transmission power
50 / 25 / 20 / 10 / 5 / 1 mW
Spurious emission (TX)
-54 dBm (47 M - 74 M, 87.5 M - 118 M,
Nominal
174 M - 230 M, 470 M - 862 MHz)
-37 dBm ( Other frequencies below 1000 MHz )
-30 dBm ( Frequencies above 1000 MHz )
-37 dBm
(PN9-9600 bps) Ch25 kHz BW:16 kHz
- 9600 bps
-113 dBm BER (1 % error)
PN9
- 4800 bps
-117 dBm BER (1 % error)
PN9
Adjacent channel selectivity
50 dB (+/-12.5 kHz) @ 4800 bps
2 signal method, PN9, 1 % error
50 dB (+/-25 kHz) @ 9600 bps
2 signal method, PN9, 1 % error
Adjacent CH leakage power ( ACP )
Receiver sensitivity
Spurious radiation (RX)
-57 dBm ( < 1000 MHz )
-47 dBm ( > 1000 MHz )
70 dB
+/- 2 MHz, +/- 10 MHz
Parameter
Specification
Remark
Power on to TX/RX
350 ms typ.
TX/RX switching time
10 ms typ.
Blocking
Timing
Interface
Parameter
Specification
Remark
Data Interface ( DI / DO )
L=GND H=VCC, Asynchronous
Transparent interface
Command interface (TXD / RXD)
UART 9600 / 19200 / 38400 bps, 8 data bit,
No parity, 1 stop bit
* Unless otherwise specified, specifications are typical values obtained under 9600 bps, 10 mW, 25 C, 434 MHz, 3V
* Specifications are subject to change without prior notice
www.circuitdesign.jp
STD-601 400 MHz ver1.4e Jul. 2015
Sales Division
7557-1 Hotaka, Azumino, Nagano 399-8303, Japan
Tel:+81-(0)263-82-1024
Fax:+81-(0)263-82-1016
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement