INSTALLATION INSTRUCTIONS
FTL5607
TOYOTA TACOMA 4WD LEVELING KIT
1
FT5607i
INSTRUCTIONS
2
FT70370
FRONT STRUT SPACER
1
FT70371
HARDWARE KIT
1
FTAS12
STICKER FT BLUE 10X4
1
FTAS16
DRIVER WARNING DECAL
1
FTREGCARD
REGISTRATION CARD
FT70371 - HARDWARE KIT
8
M10-1.5 x 25MM HEX BOLT
8
M10 SPLIT LOCK WASHER
8
M10 FLAT WASHER
1
THREAD LOCKING COMPOUND
LOCATION
2024 TOYOTA TACOMA 4WD
LEVELING KIT
FTL5607
NOTE: TO ORDER WEARABLE REPLACEMENT COMPONENTS DO NOT USE PART NUMBERS SHOWN ON THIS
INSTRUCTION SHEET. GO TO FABTECH WEBSITE AND LOOK UP WEARABLE REPLACEMENT PARTS TO FIND THE PROPER
PART NUMBER TO ORDER.
Fabtech Motorsports | 2213 Industrial Park Rd. Lancaster, SC 29720
Tech Line: 909-597-7800 | Web: www.fabtechmotorsports.com
- TOOL LIST Required Tools (Not Included)
Basic Hand Tools
Floor Jack
Jack Stands
Assorted Metric and S.A.E sockets, and Allen wrenches
Torque Wrench
- PRE-INSTALLATION NOTES For technical assistance call: 909-597-7800 or e-mail: [email protected]
READ THIS BEFORE YOU BEGIN INSTALLATION Check all parts to the parts list above before beginning installation. If any parts are missing contact Fabtech at 909-597-7800
and a replacement part will be sent to you immediately.
This suspension and shocks have been designed to be installed on a stock vehicle.
Read all instructions thoroughly from start to finish before beginning the installation. If these instructions are not properly
followed severe frame, driveline and / or suspension damage may occur.
Check your local city and state laws prior to the installation of this system for legality. Do not install if not legal in your area.
Prior to the installation of this suspension system perform a front end alignment and record. Do not install this system if the
vehicle alignment is not within factory specifications. Check for frame and suspension damage prior to installation.
The installation of this suspension system should be performed by two professional mechanics. This suspension must be
installed with Fabtech shock absorbers.
Installation of all fasteners requires the use of provided thread locking compound with proper torque values as indicated
throughout the installation. Apply thread locking compound upon the final torque of the fastener.
WARNING- Installation of this system will alter the center of gravity of the vehicle and may increase roll over as compared to
stock. Extreme care should be taken to operate the vehicle safely at all times to prevent rollover or loss of control resulting in
serious injury or death.
Vehicles that receive oversized tires should check ball joints, uniballs, tie rods ends, pitman arm and idler arm every 25005000 miles for wear and replace as needed.
Verify differential fluid is at manufactures recommended level prior to kit installation. Installation of the kit will reposition the
differential and the fill plug hole may be in a different position. (For example, if the manufacture recommends 3 quarts of
fluid, make sure the diff has 3 quarts of fluid). Check your specific manual for correct amount of fluid.
Read all warnings and warranties on the last page of these instructions before starting installation.
FOOTNOTES - Some models may not sit level after install
- Will not fit TRD Pro Models
2 of 6
- INSTRUCTIONS -
4. Remove the sway bar link bolt attaching the sway bar link
to the lower control arm. Save hardware and disconnect
the link from the arm. SEE FIGURES 3-4
1. Disconnect the negative terminal on the battery. Jack up
the front end of the truck and support the frame rails with
jack stands. NEVER WORK UNDER AN UNSUPPORTED
VEHICLE! Remove the front tires.
2. Remove the cotter pin from the tie rod end ball joint.
Loosen the nut and using a hammer strike the knuckle ball
joint housing to dislodge the tie rod end. Careful not to
damage the tie rod end. SEE FIGURE 1
FIGURE 3 - STEP 4
FIGURE 1 - STEP 2
3. Remove the cotter pin from the tie rod end ball joint nut.
Loosen the nut and using a hammer strike the knuckle
ball joint housing to dislodge the upper control arm
from the knuckle. Do not remove the nut at this time.
SEE FIGURE 2
FIGURE 4 - STEP 4
5. Disconnect the upper control arm from the knuckle. Save
hardware. SEE FIGURE 5
FIGURE 2 - STEP 3
FIGURE 5 - STEP 5
3 of 6
6. Remove the lower strut bolt and upper strut nuts, then
remove the factory strut from the truck.
9. Install the strut into the upper mount using the supplied
M10 bolts and washers. Torque the upper to 40 ft-lbs.
SEE FIGURE 9
7. Locate the four factory studs on the strut top cap.
Measure 1/2” from the base of the stud and mark. The
rest of the stud will need to be removed. SEE FIGURE 6
1/2”
FIGURE 9 - STEP 9
FIGURE 6 - STEP 7
8. Install FT70370 (Strut Spacer) onto the strut using the
factory nuts. SEE FIGURES 7-8
10. Using a round pry tool. Rotate the lower strut clockwise to
line up to the lower strut mount. Then, Install the factory
hardware and torque the lower factory bolt to 148 ft-lbs.
SEE FIGURES 10-11
FIGURE 10 - STEP 9
FIGURE 7 - STEP 8
FIGURE 11 - STEP 9
FIGURE 8 - STEP 8
4 of 6
19. Check the fluid in the front and rear differential and fill
if needed with factory specification differential oil. Note
- some differentials may expel fluid after filling and
driving. This can be normal in resetting the fluid level
with the new position of the differential/s.
11. Reconnect the upper control arm to the knuckle using the
factory nut. Torque to 35 ft-lbs. NOTE: Make sure the cv
axle is inserted into the hub. SEE FIGURE 12
20. Check ball joints, uniballs bearings, bushings and all
steering components every 2500-5000 miles for wear and
replace as required.
21. Install Driver Warning Decal. Complete product
registration card and mail to Fabtech in order to receive
future safety and technical bulletins on this suspension.
22. Review all included warnings and warranties with
consumer
For technical assistance call: 909-597-7800
FIGURE 12 - STEP 11
12. Install the factory sway bar endlink to the lower control
arm. Torque to 78 ft-lbs.
13. Install the tie rod end to the knuckle using the factory
hardware and supplied cotter pin. Torque to 35 ft-lbs.
14. Repeat steps on the passenger side.
15. Install tires and wheels and torque lug nuts to wheel
manufacturer’s specifications. Turn front tires left to right
and check for appropriate tire clearance. Note - Some
oversized tires may require trimming of the front bumper &
valance.
16. Check front end alignment and set to factory
specifications. Readjust headlights.
17. Recheck all bolts for proper torque. RE-TORQUE ALL
NUTS, BOLTS AND LUGS AFTER 50 MILES AND
PERIODICALLY THEREAFTER UNTIL TORQUE
VALUES ARE RETAINED.
18. Recheck brake hoses, ABS wires and suspension parts
for proper tire clearance while turning tires fully left to
right.
5 of 6
- Product Warranty & Warnings Fabtech provides a Limited Lifetime Warranty to the original retail purchaser who owns the
vehicle, on which the product was originally installed, for defects in workmanship and materials.
The Limited Lifetime Warranty excludes the following Fabtech items; bushings, bump stops, ball
joints, Uniball bearings, tie rod ends, limiting straps, cross shafts, heim joints and driveshafts.
These parts are subject to wear and are not considered defective when worn. They are
warranted for 60 days from the date of purchase for defects in workmanship.
Dirt Logic take apart shocks are considered a serviceable shock with a 1-year warranty against
any manufacturer’s defects. If a shock fails within the initial year of ownership, the owner
must ship the shock to Fabtech for inspection and service. If after examination the shock is
determined to have failed due to neglect, damage caused by improper installation, or any
reason other than “normal wear and tear,” the owner of the shock will be responsible for all
service costs. Costs include labor, parts, and shipping. Service seal kits are available separately
for future maintenance. All other shocks are covered under our Limited Lifetime Warranty.
Fabtech does not warrant any product for finish, alterations, modifications and/or installation
contrary to Fabtech’s instructions. Alterations to the finish of the parts including but not limited
to painting, powder coating, plating and/or welding will void all warranties. Some finish damage
may occur to parts during shipping, which is considered normal and is not covered under
warranty.
Fabtech products are not designed nor intended to be installed on vehicles used in race
applications or for racing purposes or for similar activities. This warranty does not include
coverage for police, taxi, first responder vehicles, race vehicles, or vehicles used for
government, commercial or fleet purposes. Also excluded from this warranty are sales outside
of the United States of America.
Installation of most suspension products will raise the center of gravity of the vehicle and will
cause the vehicle to handle differently than stock. It may increase the vehicle’s susceptibility
to a rollover, on road and off road, at all speeds. Extreme care should be taken to operate the
vehicle safely at all times to prevent rollover or loss of control resulting in serious injury or death.
Oversized tires and wheels may decrease the vehicle’s braking capacity. Drivers should always
brake early and be aware of the increased the stopping distance of the vehicle. Drivers should
adjust their driving habits to the effectiveness of the braking. Adjust your driving habits to these
changes.
Failure to drive safely may result in serious injury or death to driver and passengers. Driver and
passengers must ALWAYS wear your seat belts, avoid quick sharp turns and other sudden
maneuvers
Instruction Sheet Part# - FT5607i
06/19/24
6 of 6
">