2000A PORTABLE JUMP
STARTER
16000MAH
CTJMPSTC20A
2
SAFETY & WARNINGS
Read all instructions in this guide before using this product. Retain this guide for future
reference.
• Do not use this jump starter if any cable, clamp or cord is damaged.
• Do not connect two clamps together when the jump starter is on.
• Do not connect both cable clamps to the same piece of metal as this may damage the
jump starter.
• DO NOT use this jump starter to start a bulging or damaged car battery.
• Handle this jump starter with care. Avoid dropping or striking the product heavily and
repeatedly.
• DO NOT disassemble or modify this jump starter.
• Keep this jump starter away from children and pets.
• If this product shows any sign of damage, swelling, leakage or odour, cease
immediately and contact help.Kogan.com for support.
• Do not expose this product to fire or other sources of heat.
• Do not attempt to jump start a vehicle continuously. Allow at least 30 seconds to 1
minute between starts.
• To avoid damage, do not use the jump starter when the battery power is less than 10%.
• Before first use charge the jump starter for at least 3 hours to ensure it is fully charged.
• For normal use, please confirm that the unit has at least 50% power before use.
• If the positive clamp of the starting power was incorrectly connected to the negative
poles of the car battery, the reverse polarity protection will enable to avoid personal
injury and property damage.
3
COMPONENTS
• Jump starter
• Battery clamp
• USB Charging cable
• User guide
• Carry bag
OVERVIEW
2
3
1
4 5
10
6 7
9
8
4
1
Display
6
USB-A2 output
2
Wireless charging pad
7
USB-A1 output
3
Jump start output
8
Power button
4
USB-C input
9
Light button
5
Micro USB input
10
LED flashlight
OPERATION
Charging The Portable Jump Starter
1.
Connect a USB power adapter (not provided) to an electrical outlet. Connect the
charging cable into the USB-C input on the jump starter and connect the other
end into the power adapter.
2.
Press the power button to switch the jump starter on. While charging, the
percentage of battery capacity will illuminate on the display screen.
3.
Unplug the USB-C cable when charging is completed.
Input
Notes:
• Ensure the jump starter is charged for at least 3 hours for the first time.
• Use the provided USB-C cable to charge the jump starter.
• A power adapter is not provided.
5
Power Bank
1.
Press the power button to turn the jump starter on.
2.
a. Connect the jump starter to a device (i.e., smart phone, tablet, laptop or another
electronic device) using a USB cables.
b. Place the phone on the wireless charging pad.
3.
Disconnect the jump starter when charging is no longer required.
Jump Start a Vehicle
Notes:
• This jump starter is for a 12V vehicles (up to 8.0L petrol or 4.0L diesel engine) only.
• Ensure the battery power of the jump starter is more than 50% before using it to
start a car.
1.
Insert the plug of the battery clamp completely into the jump starter.
2.
Press the power button
3.
Connect the red clamp to the positive terminal (+) of the car battery and connect
the black clamp to the negative terminal (-) of the car battery.
4.
Start the vehicle.
5.
After the vehicle has started, remove the red and black clamps from the battery
and then remove battery clamps from the jump starter.
Flashlight
• Press power button, then press the light button to
turn on the flashlight.
• Press the power button to switch between the
following modes: Solid, Flash, SOS and Off.
Light
• The light has approximately 35 hours of continuous
use when fully charged.
6
Light
button
LED Display
Item
Description
Standby
Battery clamp connected, the symbol
from left to right.
Low voltage
protection
Parameters
will rotate
N/A
When the power of the jump starter is too low, after
connecting the clamps to the vehicle battery. The
14.0V ±0.5V
second. The current voltage of the starter power is
displayed.
High voltage
protection
When the car voltage is too high, after connecting the
starter to the vehicle battery, "888" flashes on the
display the buzzer beeps for a long time.
17.5V ±0.5V
Reverse
polarity
protection
If the red/black clamps are reverse connected to the
vehicle battery. The
symbol flashes, buzzer sounds once a second.
N/A
Short circuit
protection
If the red/black clamps are short circuited in the standby
state.
buzzer sounds once a second.
N/A
Over
frequency
start
protection
If the jump starter is used 8 times continuously the
8 times
Car battery
voltage
detection
When the red/black clamps are connected to the
vehicle battery (battery voltage needs to be 8V). The
vehicle battery voltage will be
displayed.
N/A
Reverse
charge
detection
The protection will be activated when the voltage at the
battery clamp is greater than the voltage at the jump
start output. The
symbol
flashes. The buzzer sounds once a second. The jump
starter will return to normal after the fault has been
eliminated.
V 0.3V
7
8
Start overrun
protection.
If the jump starter's voltage drops below 6.5V and
remains at that level for more than 0.2 seconds, or if it
falls below 5V and lasts for more than 0.02 seconds, the
protection is triggered, and the
symbol flashes.
N/A
Cable fault
protection.
When the battery clamp is powered on for the first time
and the relay is stuck, the
symbol will flash, and
the buzzer will beep for an extended period as a
protection measure.
N/A
Timeout
protection
When the battery clamp is connect, if it remains active
for more than 30 seconds, the battery clamp will
automatically turn off the output, and the
symbol
will flash.
30 seconds
CLEANING & CARE
• Store the product in a shaded, well-ventilated area.
• DO NOT use detergents to clean this jump starter.
• DO NOT expose the jump starter to extreme temperatures for an extended period. The
operating temperature of this jump starter is -20-60°C. The storage temperature of this
jump starter must not exceed 50°C.
• Charge the battery of this jump starter at least once every three months.
SPECIFICATIONS
Capacity
84.36Wh
EC5 output
12V/2500A max starting power
USB-A1 output
5V/3A, 9V/2A, 12V/1.5A
USB-A2 output
5V/2.1
Wireless charging output
5W/7.5W/10W Max
USB-C input/output
5V/3A, 9V/2A
Micro USB input
5V/2A
Charging time
Approx. 5-8 Hours
LED light power
White 1W
Working temperature
-20 °C ~+60 °C / -4 °F ~+140°F
Dimensions
209x107x56.4mm
9
NOTES
10
11
Need more information?
12
">