User`s manual | Owner`s Manual - Appliances Connection

www.reebokfitness.com
Model No. RBEL07913.0
Serial No.
Write the serial number in the space
above for reference.
Serial Number
Decal (under frame)
ACTIVATE YOUR
WARRANTY
To register your product and
activate your warranty today,
go to www.reebokservice.com/
registration.
CUSTOMER CARE
For service at any time, go to
www.reebokservice.com.
Or call 1-877-994-4999
Mon.––Fri. 6 a.m.––6 p.m. MT
Sat. 8 a.m.––4 p.m. MT
Please do not contact the store.
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Keep this manual
for future reference.
USER’’S MANUAL
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
PART IDENTIFICATION CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
HOW TO USE THE ELLIPTICAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
FCC INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
PART LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
EXPLODED DRAWING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
LIMITED WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
WARNING DECAL PLACEMENT
This drawing shows the location(s) of the warning
decal(s). If a decal is missing or illegible, see the
front cover of this manual and request a free
replacement decal. Apply the decal in the location shown. Note: The decal(s) may not be shown
at actual size.
REEBOK and the Vector Logo
are registered trademarks and service marks of Reebok.
This product is manufactured and distributed under license from Reebok International.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read
all important precautions and instructions in this manual and all warnings on your elliptical before
using your elliptical. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
1. It is the responsibility of the owner to ensure
that all users of the elliptical are adequately
informed of all precautions.
11. Do not operate the elliptical if the power cord
or plug is damaged, or if the elliptical is not
working properly.
2. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or persons with pre-existing health problems.
12. Always unplug the power cord and switch
the power switch to the off position when the
elliptical is not in use.
13.
3. Use the elliptical only as described in this
manual.
DANGER: Always unplug the power
cord when the elliptical is not in use and
before cleaning the elliptical. Servicing other
than the procedures in this manual should
be performed by an authorized service representative only.
4. The elliptical is intended for home use only.
Do not use the elliptical in a commercial,
rental, or institutional setting.
14. The elliptical should not be used by persons
weighing more than 300 lbs. (136 kg).
5. Keep the elliptical indoors, away from moisture and dust. Do not put the elliptical in a
garage or covered patio, or near water.
15. Wear appropriate clothes while exercising;
do not wear loose clothes that could become
caught on the elliptical. Always wear athletic
shoes for foot protection while exercising.
6. Place the elliptical on a level surface, with at
least 3 ft. (0.9 m) of clearance in the front and
rear of the elliptical and 2 ft. (0.6 m) on each
side. To protect the floor or carpet from damage, place a mat under the elliptical.
16. Hold the handlebars or the upper body arms
when mounting, dismounting, or using the
elliptical.
7. Inspect and properly tighten all parts regularly. Replace any worn parts immediately.
8. Keep children under age 12 and pets away
from the elliptical at all times.
17. The heart rate monitor is not a medical
device. Various factors may affect the accuracy of heart rate readings. The heart rate
monitor is intended only as an exercise aid
in determining heart rate trends in general.
9. When connecting the power cord, plug the
power cord into a grounded circuit. To avoid
overloading the circuit, do not plug other
electrical devices, except for low-power
devices such as cell phone chargers, into an
outlet on the same circuit.
18. The elliptical does not have a freewheel; the
pedals will continue to move until the flywheel stops. Reduce your pedaling speed in
a controlled way.
19. Keep your back straight while using the elliptical; do not arch your back.
10. Do not modify the power cord or use an
adapter to connect the power cord to an
improper receptacle. Keep the power cord
away from heated surfaces. Do not use an
extension cord.
20. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
SAVE THESE INSTRUCTIONS
3
4
STANDARD SERVICE PLANS
all
5
BEFORE YOU BEGIN
Thank you for selecting the revolutionary REEBOK®
710 elliptical. The 710 elliptical provides an impressive
selection of features designed to make your workouts
at home more effective and enjoyable.
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
For your benefit, read this manual carefully before
you use the elliptical. If you have questions after
reading this manual, please see the front cover of this
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Console
Length: 6 ft. 8 in. (203 cm)
Width: 2 ft. 2 in. (66 cm)
Heart Rate Monitor
Upper Body Arm
Handlebar
Accessory Tray
Ramp
Storage Magnet
Wheel
Access Cover
Pedal
Power
Switch
Leveling Foot
Latch Button
Handle
Pedal Arm Latch
Leveling Foot
6
PART IDENTIFICATION CHART
Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each
drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the
key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it
has been preassembled. Extra parts may be included.
M8 Split
Washer
(131)––8
M6 Washer
(140)––8
M8 Locknut
(105)––6
M4 x 16mm
Screw (93)––14
M8 x 16mm
Screw (102)––12
M8 x 25mm x
1.5mm Washer
(126)––4
M6 x 12mm
Screw (139)––4
M17 Wave
Washer (88)––4
M6 x 50mm
Screw (62)––4
M8 x 45mm Bolt
(104)––6
M8 x 25mm
Screw (128)––2
M10 x 120mm
Screw (100)––4
7
ASSEMBLY
•• To hire an authorized service technician to
assemble this product, call 1-800-445-2480.
•• To identify small parts, see page 7.
•• In addition to the included tool(s), assembly
requires the following tools:
•• Assembly requires two persons.
•• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until you nish all assembly steps.
one Phillips screwdriver
•• Left parts are marked ““L”” or ““Left”” and right parts
are marked ““R”” or ““Right.””
Assembly may be easier if you have your own set
of wrenches. To avoid damaging parts, do not use
power tools.
one rubber mallet
1. Go to www.reebokservice.com/registration
on your computer and register your product.
1
•• activates your warranty
•• saves you time if you ever need to contact
Customer Care
•• allows us to notify you of upgrades and offers
Note: If you do not have Internet access, call
CUSTOMER CARE (see the front cover of this
manual) and register your product.
2. While a second person lifts the Folding Frame
(2), attach the Rear Stabilizer (4) to the Folding
Frame with two M10 x 120mm Screws (100).
Note: The Folding Frame may be in the folded
position.
2
Note: If the elliptical is in the folded position,
unfold it after completing this step. To unfold the
elliptical, hold the handle on the Rear Stabilizer
(4), press the Latch Button (67), and lower the
Rear Stabilizer and the Folding Frame (2) to the
floor.
4
67
2
100
8
Handle
3. Orient the Front Stabilizer (3) as shown.
3
While a second person lifts the front of the
Frame (1), attach the Front Stabilizer (3) with
two M10 x 120mm Screws (100).
3
100
1
4. Identify and orient the Upright (5) and the Top
Cover (23) as shown.
4
Slide the Top Cover (23) upward onto the
Upright (5).
Wire Tie
Avoid pinching the
Upright Wire (60)
Have a second person hold the Upright (5) and
the Top Cover (23) near the Frame (1).
Locate the wire tie in the Upright (5). Tie the
lower end of the wire tie to the Upright Wire (60).
Next, pull the upper end of the wire tie until the
Upright Wire is routed through the Upright.
5
23
Tip: To prevent the Upright Wire (60) from
falling into the Upright (5), secure the Upright
Wire with the wire tie.
102
Wire Tie
Tip: Avoid pinching the Upright Wire (60).
Slide the Upright (5) onto the Frame (1).
60
131
1
Attach the Upright (5) with eight M8 x 16mm
Screws (102) and eight M8 Split Washers (131)
(only four of each are shown); do not tighten
the Screws yet.
131
102
102
Do not press the Top Cover (23) into place
yet.
9
131
5. Identify the Right Upper Body Arm (8) and the
Right Upper Body Leg (6) and orient them as
shown.
5
Insert the Right Upper Body Arm (8) into the
Right Upper Body Leg (6).
Attach the Right Upper Body Arm (8) with three
M8 x 45mm Bolts (104) and three M8 Locknuts
(105). Make sure that the Locknuts are inside
the hexagonal holes. Do not fully tighten the
Bolts yet.
9
Assemble the Left Upper Body Arm (9) and
the Left Upper Body Leg (7) in the same way.
8
104
104
105
105
104
7
Hexagonal
Holes
6
6. Using a small plastic bag to keep your fingers
clean, apply a generous amount of the included
grease to the Upright Axle (48) and to two M17
Wave Washers (88).
6
Avoid damaging the
Upright Wire (60)
Tip: Avoid damaging the Upright Wire (60).
Insert the Upright Axle (48) through the Upright
(5) and center it. Slide an M17 Wave Washer
(88) onto each side of the Upright Axle.
60
9
Slide the Right and Left Upper Body Arms
(8, 9) onto the right and left sides of the Upright
Axle (48).
102
Tighten an M8 x 16mm Screw (102) and an M8
x 25mm x 1.5mm Washer (126) into each end of
the Upright Axle (48) at the same time.
126
5
88
48
88
Grease
8
126
102
10
7. Note: The Leveling Foot (41) may be
preattached.
7
With the help of a second person, place some of
the packaging materials (not shown) under the
Frame (1). Have the second person hold the
Frame to prevent it from tipping while you
complete this step.
1
Tighten the Leveling Foot (41) into the underside
of the Frame (1).
41
8. Identify the Right Pedal (14) and the Right Pedal
Arm (12) assembly and orient them as shown.
8
Attach the Right Pedal (14) to the Right Pedal
Arm (12) with two M6 x 12mm Screws (139)
and two M6 Washers (140); do not tighten the
Screws yet.
14
Next, tighten two M6 x 50mm Screws (62) with
two M6 Washers (140) into the Right Pedal Arm
(12) and the Right Pedal (14). Then, tighten the
four M6 x 12mm Screws (139).
12
140
Attach the Left Pedal (not shown) to the Left
Pedal Arm (not shown) assembly in the same
way.
139
62
140
11
9. See the upper drawing. Locate the Ramp
Roller (92) on the Right Pedal Arm (12).
9
12
Set the Ramp Roller (92) on the right side of the
Ramp (43).
92
See the lower drawing. Pull upward on the
Latch (117) on the Right Pedal Arm (12).
Press the Right Pedal Arm (12) onto the right
Sleeve (136). Make sure that the Right Pedal
Arm latches into place.
Repeat this step on the other side of the
elliptical.
43
12
117
136
10. Orient the Ramp Cover (44) around the Upright
(5) as shown.
10
Press the mounts on the underside of the Ramp
Cover (44) into the Ramp (43).
44
5
43
12
11. Apply grease to a Link Arm Axle (94) and to an
M17 Wave Washer (88).
11
First, insert the Link Arm Axle (94) into the Right
Upper Body Leg (6) from the side shown. Next,
slide the M17 Wave Washer (88) onto the Link
Arm Axle. Then, insert the Link Arm Axle into the
Right Link Arm (90).
7
128
91
Insert a hex key into the M8 x 25mm Screw
(128) in the Link Arm Axle (94).
94
6
88 90
Using a second hex key, tighten another
M8 x 25mm Screw (128), a Pivot Axle Cover
(111), and an M8 x 25mm x 1.5mm Washer (126)
into the other end of the Link Arm Axle (94).
Tip: Avoid damaging the Pivot Axle Cover
when tightening the Screw.
126
Grease
111
128
Repeat this step on the other side of the
elliptical.
12. Tighten the six M8 x 45mm Bolts (104) and
the eight M8 x 16mm Screws (102).
12
Then, press the Top Cover (23) into the Right
and Left Frame Covers (21, 22).
104
104
23
102
21, 22
13
102
13. Tip: Avoid pinching the wires. Attach the Rear
Upright Cover (24) to the Upright (5) with four M4
x 16mm Screws (93). Tip: It may be necessary
to bend the upper end of the Rear Upright
Cover gently into place around the Upright.
13
Avoid pinching
the wires
5
93
24
14. Orient the Front Upright Cover (25) as shown.
14
Attach the Front Upright Cover (25) around the
Upright (5) by pressing it into the Rear Upright
Cover (24).
25
5
24
15. Identify the Right Front Leg Cover (30).
15
Attach the Right Front Leg Cover (30) to the
Right Upper Body Arm (8) with two M4 x 16mm
Screws (93).
32
Repeat this step on the other side of the
elliptical.
8
93
14
30
16. Identify the Right Rear Leg Cover (29).
16
Attach the Right Rear Leg Cover (29) around the
Right Upper Body Arm (8) by pressing it into the
Right Front Leg Cover (30).
8
Repeat this step on the other side of the
elliptical.
30
29
17. Orient the Console Cover (11) as shown. Slide
the Console Cover onto the Upright (5).
17
11
5
15
18. Have a second person hold the Handlebar (10)
near the Upright (5).
18
10
135
See the inset drawing. Locate the Pulse Wire
(135) in the Handlebar (10). Insert the Pulse
Wire into the front of the Upright (5) and pull it
out of the hole in the Upright as shown.
5
Tie the end of the wire tie to the Upright Wire
(60) and the Pulse Wire (135). Then, insert the
other end of the wire tie upward through the
Handlebar (10). Next, pull the upper end of the
wire tie until the Upright Wire and the Pulse Wire
are routed through the Upright.
10
Wire
Tie
5
60, 135
19. Tip: Avoid pinching the wires. Attach the
Handlebar (10) to the Upright (5) with two M8 x
16mm Screws (102).
19
Avoid pinching
the wires
10
102
5
16
20. While a second person holds the Console (33)
near the Handlebar (10), connect the wires on the
Console to the Upright Wire (60) and to the Pulse
Wire (135).
20
33
Avoid pinching
the wires
Insert the excess wire into the Handlebar (10) or
into the Console (33).
135
Tip: Avoid pinching the wires. Attach the
Console (33) to the Handlebar (10) with four M4
x 16mm Screws (93).
10
60
93
21. Attach the Console Cover (11) to the Handlebar
(10) with two M4 x 16mm Screws (93).
21
10
11
93
22. Make sure that all parts are properly tightened before you use the elliptical. Note: Extra parts may be
included. Place a mat under the elliptical to protect the floor or carpet.
17
HOW TO USE THE ELLIPTICAL
HOW TO PLUG IN THE POWER CORD
A temporary
adapter may
be used to
connect the
power cord
to a 2-pole
receptacle
as shown
at the right
if a properly
grounded
outlet is not
available.
This product must be grounded. If it should malfunction or break down, grounding provides a path of least
resistance for electric current to reduce the risk of
electric shock. The power cord has a plug with a
grounding pin.
DANGER: Improper connection of
the power cord increases the risk of electric
shock. Do not modify the plug; if it will not fit
an outlet, have a proper outlet installed by a
qualified electrician. If you are unsure whether
the product is properly grounded, contact a
qualified electrician.
2-pole Receptacle
Adapter
Lug
Metal Screw
The lug or wire extending from the adapter must
be connected with a metal screw to a permanent
ground such as a properly grounded outlet box cover.
Some 2-pole receptacle outlet box covers are not
grounded. Before using an adapter, contact a qualified electrician to determine whether the outlet
box cover is grounded before using an adapter.
The temporary adapter should be used only until
a properly grounded outlet can be installed by a
qualified electrician.
Plug the
power cord
Grounded Outlet
into an
appropriate
Grounding Pin
outlet that
is properly
installed and
grounded in
accordance
with all local
codes and
ordinances. The outlet must be on a nominal 120-volt
circuit.
18
HOW TO FOLD AND UNFOLD THE ELLIPTICAL
HOW TO MOVE THE ELLIPTICAL
When the elliptical is not in use,
the frame can
be folded out of
the way. First, lift
the latch under
each pedal arm,
and lift the pedal
arms off the
sleeves on the
crank arms.
To move the elliptical, first fold it as described at
the left. Next, stand in front of the elliptical, hold the
upright, and place one foot against one of the wheels.
Pull the upright until the elliptical rolls on the wheels.
With the help of a second person, carefully move the
elliptical to the desired location, and then lower it to the
floor.
Latch
Pedal
Arm
Next, raise the pedal arms until the magnets on the
pedal arms touch the handlebars; the magnets will hold
the pedal arms in place. Then, hold the handle and lift
the frame until it locks in a vertical position.
Pull on the
handlebar
Place your
foot here
Magnet
Handle
Pedal
Arm
Latch
Button
To use the elliptical, first hold the handle, press the
latch button, and lower the frame.
Next, pull the magnets on the pedal arms off the handlebars. Then, lift the latches under the pedal arms,
and set the pedal arms on the sleeves on the crank
arms. Release the latches, and make sure that the
pedal arms are securely connected to the crank arms.
19
HOW TO EXERCISE ON THE ELLIPTICAL
To dismount the elliptical, wait until the pedals come to
a complete stop. Note: The elliptical does not have
a free wheel; the pedals will continue to move until
the flywheel stops. When the pedals are stationary,
step off the higher pedal first. Then, step off the lower
pedal.
To mount the elliptical, hold the upper body arms and
step onto the pedal that is in the lowest position. Next,
step onto the other pedal. Push the pedals until they
begin to move with a continuous motion.
HOW TO LEVEL THE ELLIPTICAL
If the elliptical rocks slightly on your floor during use,
turn one or both of the leveling feet beneath the rear
stabilizer until the rocking motion is eliminated.
Upper Body Arms
Handlebars
Leveling
Foot
Pedals
Crank
Arm
Leveling
Feet
If the frame of the elliptical flexes during use, turn the
center leveling foot until the flexing motion is
eliminated.
Note: The crank arms can turn in either direction.
It is recommended that you turn the crank arms
in the direction shown by the arrow; however, for
variety you can turn the crank arms in the opposite
direction.
20
CONSOLE DIAGRAM
FEATURES OF THE CONSOLE
The advanced console offers an array of features
designed to make your workouts more effective and
enjoyable.
When you use the manual mode of the console, you
can change the resistance of the pedals and the incline
of the ramp with the touch of a button.
While you exercise, the console will display continuous
exercise feedback. You can also measure your heart
rate using the handgrip heart rate monitor.
The console offers twenty-two onboard workouts. Each
workout automatically changes the resistance of the
pedals and the incline of the ramp and prompts you to
vary your pedaling pace as it guides you through an
effective workout. You can also set a customized workout goal with the set-a-goal workout.
The console also features an iFit mode that enables
the console to communicate with your wireless network
through an optional iFit module. With the iFit mode,
you can download personalized workouts, create your
own workouts, track your workout results, race against
other iFit users, and access many other features. To
purchase an iFit module at any time, go to
www.iFit.com or call the telephone number on the
front cover of this manual.
You can even connect your MP3 player or CD player
to the console sound system and listen to your favorite
music or audio books while you exercise.
To turn on the power, see page 22. To use the
manual mode, see page 22. To use an onboard
workout, see page 25. To use a set-a-goal workout, see page 26. To use an iFit workout, see page
27. To use the sound system, see page 28. To
change console settings, see page 29.
Note: If there is a sheet of plastic on the display,
remove the plastic.
21
HOW TO TURN ON THE POWER
3. Change the resistance of the pedals and the
incline of the ramp as desired.
IMPORTANT: If the elliptical has been exposed to
cold temperatures, allow it to warm to room temperature before turning on the power. If you do not
do this, you may damage the console displays or
other electrical components.
Plug in the power cord (see
HOW TO PLUG IN THE
POWER CORD on page
18). Next, locate the
power switch on the frame
near the power cord. Press
the power switch to the
reset position.
As you pedal, change the resistance of the pedals
by pressing the Resistance increase and decrease
buttons.
Note: After you press a button, it will take a
moment for the pedals to reach the selected
resistance level.
Reset
Position
To vary the motion of the pedals, you can change
the incline of the ramp. To change the incline,
press one of the numbered Quick Power Ramp
buttons or press the Quick Power Ramp increase
and decrease buttons.
The display will then turn on and the console will be
ready for use.
Note: After you press a button, it will take a
moment for the ramp to reach the selected incline
level.
Note: When you turn on the power for the rst
time, the incline of the ramp may calibrate automatically. The ramp will move upward and downward
as it calibrates. When the ramp stops moving, the ramp
is calibrated.
4. Follow your progress with the display.
The display can show the following workout
information:
IMPORTANT: If the incline of the ramp does not
calibrate automatically, see HOW TO CALIBRATE
THE RAMP on page 31 and manually calibrate
the ramp.
HOW TO USE THE MANUAL MODE
1. Begin pedaling or press any button on the
console to turn on the console.
See HOW TO TURN ON THE POWER above.
2. Select the manual mode.
Calories (Cals.)——This display mode will show the
approximate number of calories you have burned.
Press the Manual Control button on the console to
select the manual mode.
Calories per Hour (Cals./Hr)——This display mode
will show the approximate number of calories you
are burning per hour.
If a wireless iFit module is not inserted into the console and connected to iFit, the manual mode will be
selected automatically.
Distance (Dist.)——This display mode will show
the distance that you have pedaled in miles or
kilometers.
22
Incline——This display mode will show the incline
level of the ramp for a few seconds each time the
incline level changes.
Calorie——This tab will show the approximate
amount of calories you have burned. The height of
each segment represents the amount of calories
burned during that segment.
Pulse——This display mode will show your heart rate
when you use the handgrip heart rate monitor (see
step 5).
As you exercise, the workout intensity level bar
will indicate the approximate intensity level of your
exercise.
Resistance (Resist.)——This display mode will
show the resistance level of the pedals for a few
seconds each time the resistance level changes.
RPM——This display mode will show your pedaling
speed in revolutions per minute (rpm).
Stride——This display mode will show the total number of strides you have pedaled.
Press the Home button to return to the default
menu (see HOW TO CHANGE CONSOLE
SETTINGS on page 29 to set the default menu).
If necessary, press the Home button again.
Time——When the manual mode is selected, this
display mode will show the elapsed time. When an
onboard workout is selected, this display mode will
show the time remaining in the workout.
The matrix offers several display tabs. Press the
Disp. button until the desired tab is shown. You can
also press the increase and decrease buttons next
to the Enter button.
When a wireless iFit
module is connected,
the wireless symbol at
the top of the display
will show the strength
of your wireless signal.
Four arcs indicate full signal strength.
Speed——This tab will show a profile of the speed
settings of the workout. A new segment will appear
at the end of each minute.
To exit the manual mode or a workout, press the
Home button. If necessary, press the Home button
again.
My Trail——This tab will show a track that represents
1/4 mile (400 m). As you exercise, the flashing
rectangle will show your progress. The My Trail tab
will also show the number of laps you complete.
Change the volume
level of the console by
pressing the volume
increase and decrease
buttons.
23
5. Measure your heart rate if desired.
6. Turn on the fan if desired.
If there are
sheets of plasContacts
tic on the metal
contacts on the
handgrip heart
rate monitor,
remove the plastic. To measure
your heart rate,
hold the handgrip
heart rate monitor
with your palms resting against the contacts. Avoid
moving your hands or gripping the contacts
tightly.
The fan has low and
high speed settings.
Press the fan increase
and decrease buttons
repeatedly to select a fan speed or to turn off the
fan.
Note: If the pedals do not move for about thirty
seconds, the fan will turn off automatically.
7. When you are finished exercising, unplug the
power cord.
If the pedals do not move for several seconds, a
tone will sound and the console will pause.
When your pulse is detected, a heart symbol will
flash in the display each time your heart beats,
one or two dashes will appear, and then your heart
rate will be shown. For the most accurate heart
rate reading, hold the contacts for at least 15
seconds.
If the pedals do not move for several minutes and
the buttons are not pressed, the console will turn
off and the display will be reset.
When you are finished exercising, press the power
switch to the off position and unplug the power
cord. IMPORTANT: If you do not do this, the
electrical components on the elliptical may
wear prematurely.
If the display does not show your heart rate, make
sure that your hands are positioned as described.
Be careful not to move your hands excessively or
to squeeze the contacts tightly. For optimal performance, clean the contacts using a soft cloth; never
use alcohol, abrasives, or chemicals to clean
the contacts.
24
HOW TO USE AN ONBOARD WORKOUT
resistance level, ramp incline level, and/or target
rpm is programmed for the next segment, the resistance level, ramp incline level, and/or target rpm
will appear in the display for a few seconds to alert
you. The resistance of the pedals and the incline
level of the ramp will then change.
1. Begin pedaling or press any button on the
console to turn on the console.
See HOW TO TURN ON THE POWER on
page 22.
To select an onboard workout, press the 11 Calorie
Workouts button or the 11 Performance Workouts
button repeatedly until the desired workout appears
in the display.
As you exercise, you will be prompted to keep your
pedaling speed near the target rpm for the current segment. When an upward-pointing arrow
appears in the display, increase your pace.
When a downward-pointing arrow appears,
decrease your pace. When no arrow appears,
maintain your current pace.
When you select an onboard workout, the display
will show the duration of the workout and the name
of the workout. A profile of the speed settings of the
workout will appear in the matrix.
IMPORTANT: The target rpm is intended only to
provide motivation. Your actual pedaling speed
may be slower than the target rpm. Make sure
to pedal at a speed that is comfortable for you.
The display will also show the maximum speed
(rpm), the maximum resistance level, and the maximum ramp level.
If the resistance level or incline level for the
current segment is too high or too low, you can
manually override the setting by pressing the
Resistance buttons or the Quick Power Ramp buttons. IMPORTANT: When the current segment of
the workout ends, the pedals will automatically
adjust to the resistance level programmed for
the next segment and the ramp will automatically adjust to the incline level programmed for
the next segment.
2. Select an onboard workout.
3. Begin pedaling to start the workout.
Each workout is divided into one-minute segments.
One resistance level, one ramp incline level, and
one target rpm (speed) are programmed for each
segment. Note: The same resistance level, ramp
incline level, and/or target rpm may be programmed for consecutive segments.
The workout will continue in this way until the last
segment ends. To stop the workout at any time,
stop pedaling. The time will flash in the display. To
resume the workout, simply resume pedaling.
The resistance level, the ramp incline level, and the
target rpm for the first segment will appear in the
matrix.
4. Follow your progress with the display.
During the
workout,
the profiles
on the
speed and
incline
Profile
tabs will
show
your progress. The flashing segment of the profile
represents the current segment of the workout. The
height of the flashing segment indicates the target
speed or the incline level for the current segment.
See step 4 on page 22.
5. Measure your heart rate if desired.
See step 5 on page 24.
6. Turn on the fan if desired.
See step 6 on page 24.
7. When you are nished exercising, unplug the
power cord.
At the end of each segment of the workout, a
series of tones will sound and the next segment
of the profile will begin to flash. If a different
See step 7 on page 24.
25
HOW TO USE A SET-A-GOAL WORKOUT
Note: The calorie goal is an estimate of the
number of calories that you will burn during
the workout. The actual number of calories that
you burn will depend on various factors such
as your weight. In addition, if you manually
change the resistance or incline of the ramp
during the workout, the number of calories you
burn will be affected.
1. Begin pedaling or press any button on the
console to turn on the console.
See HOW TO TURN ON THE POWER on
page 22.
2. Set a calories, distance, or time goal.
The workout will continue in this way until the calories, distance, or time goal is reached. To pause
the workout, stop pedaling. The time will pause in
the display. To resume the workout, simply resume
pedaling.
To set a calories, distance, or time goal, first press
the Set A Goal button.
Next, press the increase and decrease buttons
next to the Enter button until the name of the
desired goal appears in the display. Then, press
the Enter button.
4. Follow your progress with the display.
See step 4 on page 22.
Then, press the increase and decrease buttons
next to the Enter button to set the desired goal.
5. Measure your heart rate if desired.
3. Begin pedaling to start the workout.
See step 5 on page 24.
As you exercise, a target rpm (speed) may
appear in the display to help you reach your goal.
Keep your pedaling speed near the target rpm.
IMPORTANT: The target rpm is intended only to
provide motivation. Your actual pedaling speed
may be slower than the target rpm. Make sure
to pedal at a speed that is comfortable for you.
6. Turn on the fan if desired.
See step 6 on page 24.
7. When you are nished exercising, unplug the
power cord.
See step 7 on page 24.
26
HOW TO USE AN IFIT WORKOUT
To compete in a race that you have previously
scheduled, press the Compete button.
You must have an iFit module to use an iFit workout.
To re-run a recent iFit workout from your schedule, first press the Track button. Next, press the
increase and decrease buttons to select the
desired workout. Then, press the Enter button to
start the workout.
To purchase an iFit module at any time, go to
www.iFit.com or call the telephone number on the
front cover of this manual.
Note: To use an iFit module, you must have access
to a computer with an internet connection and a USB
port. You will also need an iFit.com membership. To
use a wireless iFit module, you must also have your
own wireless network including an 802.11b router with
SSID broadcast enabled (hidden networks are not
supported).
To use a set-a-goal workout, press the Set A Goal
button (see page 26).
Note: Before some workouts will download, you
must add them to your schedule on iFit.com.
For more information about the iFit workouts,
please go to www.iFit.com.
IMPORTANT: To satisfy exposure compliance
requirements, the antenna and transmitter in the
iFit module must be at least 8 in. (20 cm) from all
persons and must not be near or connected to any
other antenna or transmitter.
When you select an iFit workout, the display will
show the name, duration, maximum ramp incline
level, and distance of the workout. The display will
also show the approximate number of calories you
will burn during the workout and a profile of the
resistance settings of the workout.
1. Begin pedaling or press any button on the
console to turn on the console.
See HOW TO TURN ON THE POWER on
page 22.
Note: The calorie goal is an estimate of the
number of calories that you will burn during
the workout. The actual number of calories that
you burn will depend on various factors such
as your weight. In addition, if you manually
change the resistance or incline of the ramp
during the workout, the number of calories you
burn will be affected.
2. Make sure that the iFit module is inserted in the
console.
To use an iFit workout, make sure that the iFit module is inserted in the console.
3. Select a user.
5. Begin pedaling to start the workout.
If more than one user is registered with your
iFit.com membership, you can switch users in the
iFit main screen. Press the increase and decrease
buttons next to the Enter button to select a user.
See step 3 on page 25.
During some workouts, the voice of a personal
trainer will guide you through your workout. You
can select an audio setting for your personal trainer
(see HOW TO CHANGE CONSOLE SETTINGS on
page 29).
4. Select an iFit workout.
To download an iFit workout in your schedule,
press the Map, Train, or Lose Wt. button to download the next workout of that type in your schedule.
To download the next workout in your schedule,
press the iFit button. Note: You may be able to
access demo workouts through these options, even
if you do not insert an iFit module.
To stop the workout at any time, stop pedaling. The
time will flash in the display. To resume the workout, simply resume pedaling.
27
6. Follow your progress with the display.
HOW TO USE THE SOUND SYSTEM
See step 4 on page 22.
The My Trail tab will show a map of the trail you are
walking or running or it will show a track and the
number of laps you complete.
To play music or audio books through the console
sound system while you exercise, plug your audio
cable into the jack on the console and into a jack on
your MP3 player or CD player; make sure that your
audio cable is fully plugged in.
During a competition workout, the Competition tab
will show your progress in the race. As you race,
the top line in the matrix will show how much of the
race you have completed. The other lines will show
other competitors. The end of the matrix represents
the end of the race.
Next, press the play button
on your MP3 player or CD
player. Adjust the volume
level using the volume
increase and decrease buttons on the console or the
volume control on your MP3 player or CD player.
7. Measure your heart rate if desired.
See step 5 on page 24.
8. Turn on the fan if desired.
See step 6 on page 24.
9. When you are nished exercising, unplug the
power cord.
See step 7 on page 24.
For more information about iFit, please go to
www.iFit.com.
28
HOW TO CHANGE CONSOLE SETTINGS
If no module is connected, the display will show
the words NO IFIT MODULE. If no module is connected, go to step 10.
The console features a user mode that allows you to
view usage information, select a unit of measurement,
and adjust the contrast level of the display.
6. Select an audio setting for the voice of the
personal trainer if desired.
When an iFit module is connected to the console,
you can also use the information mode to choose an
audio setting for the voice of the personal trainer, set a
default menu, check the status of the iFit module, and
check for downloads.
Press the decrease button to view the audio setting
for the voice of the personal trainer. The currently
selected audio setting for the voice of the personal
trainer will appear in the display.
1. Select the information mode.
To change the audio setting, press the Enter button
repeatedly to turn the voice of the personal trainer
ON or OFF.
To select the information mode, press and hold
down the Disp. button for a few seconds until the
information mode appears in the display.
7. Set the default menu if desired.
2. View usage information.
Press the decrease button to view the default menu
setting. The default menu is the menu that will
appear when you turn on the console. Press the
Enter button repeatedly to select the manual mode
menu or the iFit menu as the default menu.
The display will show the total number of hours that
the elliptical has been used. The display will also
show the total distance (in miles or kilometers) that
has been pedaled on the elliptical.
8. Check the status of the iFit module if desired.
3. Select a unit of measurement if desired.
Press the decrease button to view the iFit status display. The words CHECK WIFI STATUS or
CHECK USB STATUS will appear in the display.
The word ENGLISH for English miles or the word
METRIC for metric kilometers will appear in the
display to indicate the currently selected unit of
measurement.
Then, press the Enter button. After a few seconds,
the status of the iFit module will appear in the display. To exit this display, press and hold down the
Disp. button for a few seconds.
To change the unit of measurement, press the
Enter button repeatedly to select the desired unit of
measurement.
9. Check for downloads if desired.
4. Adjust the contrast level of the display if
desired.
Press the decrease button to view the downloads
display. The words SEND/RECEIVE DATA will
appear in the display.
Press the decrease button to view the contrast
level. The currently selected contrast level will
appear in the display. Press the Quick Power
Ramp increase and decrease buttons to adjust the
contrast level.
Then, press the Enter button. The console will then
check for iFit workouts and firmware downloads.
10. Exit the information mode.
5. Determine if an iFit module is connected to the
console.
Press the Disp. button to exit the information mode.
If an iFit module is connected to the console, the
display will show the words WIFI MODULE or USB
MODULE.
29
FCC INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, try to correct the interference by one or more of the following measures:
••
••
••
••
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION: To assure continued compliance, use only shielded interface cables when connecting to
computer or peripheral devices. Changes or modifications not expressly approved by the party responsible for compliance could void the user’’s authority to operate this equipment.
30
MAINTENANCE AND TROUBLESHOOTING
Inspect and tighten all parts of the elliptical regularly.
Replace any worn parts immediately.
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted.
To clean the elliptical, use a damp cloth and a small
amount of mild soap. IMPORTANT: To avoid damage
to the console, keep liquids away from the console
and keep the console out of direct sunlight.
To adjust the
reed switch,
first unplug the
power cord.
Using a flat
screwdriver,
release the tabs
on the Top Cover
(20) and pry
the Top Cover
upward off the
elliptical.
HEART RATE MONITOR TROUBLESHOOTING
If the console does not turn on, make sure that the
power cord is fully plugged in. If lines appear in the
console display, see HOW TO CHANGE CONSOLE
SETTINGS on page 29 and adjust the contrast level
of the display.
If the console does not display your heart rate when
you hold the handgrip heart rate monitor, or if the displayed heart rate appears to be too high or too low, see
step 5 on page 24.
20
Next, look into the access opening and locate the
Reed Switch (69). Rotate the Large Pulley (74) until a
Magnet (75) is aligned with the Reed Switch.
HOW TO CALIBRATE THE RAMP
If the ramp is not functioning properly, the ramp may
need to be calibrated. To calibrate the ramp, press
and hold the 11 Calorie Workouts button for several
seconds until the test mode appears in the display.
Press the 11 Calorie Workouts button again. Press
the Quick Power Ramp increase or decrease button
to calibrate the ramp. The ramp will move upward and
downward as it calibrates.
When the ramp stops moving, the ramp is calibrated.
Then, press the 11 Calorie Workouts button repeatedly
to exit the test mode.
93 75
69
74
Next, loosen, but do not remove, the indicated M4 x
16mm Screw (93). Slide the Reed Switch (69) slightly
toward or away from the Magnet (75). Then, retighten
the M4 x 16mm Screw.
Plug in the power cord and rotate the large pulley for
a moment. Repeat these actions until the console
displays correct feedback. When the reed switch is
correctly adjusted, reattach the access cover.
31
HOW TO ADJUST THE DRIVE BELT
See EXPLODED DRAWING B on page 37. Remove
the M4 x 16mm Screws (93) and the M4 x 42mm
Screws (124) from the Right and Left Shields (18, 19).
Make sure to note which size Screws come from
which holes. Then, carefully remove the Left Shield.
If you can feel the pedals slip while you are pedaling,
even when the resistance is adjusted to the highest
level, the drive belt may need to be adjusted.
To adjust the drive belt, first unplug the power cord.
Using a flat screwdriver, release the tabs on the Top
Cover (20) and pry the Top Cover upward off the
elliptical.
Loosen the Pivot Screw (97). Tighten the Belt
Adjustment Screw (85) until the Drive Belt (38) is tight.
When the Drive Belt is tight, tighten the Pivot Screw.
38
97
20
85
19, 18
136
13
117
124
When you are finished, reattach the left shield, replace
the left pedal arm, and reattach the access cover.
Then, plug in the power cord.
Next, lift the Latch (117) on the underside of the Left
Pedal Arm (13), and then lift the Left Pedal Arm off the
left Sleeve (136).
32
EXERCISE GUIDELINES
Burning Fat——To burn fat effectively, you must exercise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
WARNING:
Before beginning this
or any exercise program, consult your physician. This is especially important for persons
over age 35 or persons with pre-existing
health problems.
The heart rate monitor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The heart rate monitor is
intended only as an exercise aid in determining heart rate trends in general.
Aerobic Exercise——If your goal is to strengthen your
cardiovascular system, you must perform aerobic
exercise, which is activity that requires large amounts
of oxygen for prolonged periods of time. For aerobic
exercise, adjust the intensity of your exercise until your
heart rate is near the highest number in your training
zone.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
WORKOUT GUIDELINES
EXERCISE INTENSITY
Warming Up——Start with 5 to 10 minutes of stretching and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper intensity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
Training Zone Exercise——Exercise for 20 to 30 minutes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise; never hold your breath.
Cooling Down——Finish with 5 to 10 minutes of stretching. Stretching increases the flexibility of your muscles
and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the nearest ten years). The three numbers listed above your
age define your ““training zone.”” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months of regular exercise, you may complete up to five workouts each week,
if desired. Remember, the key to success is to make
exercise a regular and enjoyable part of your everyday
life.
33
PART LIST
Key No. Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
4
1
2
8
3
1
1
1
1
4
1
1
1
1
Model No. RBEL07913.0 R0113A
Description
Key No. Qty.
Frame
Folding Frame
Front Stabilizer
Rear Stabilizer
Upright
Right Upper Body Leg
Left Upper Body Leg
Right Upper Body Arm
Left Upper Body Arm
Handlebar
Console Cover
Right Pedal Arm
Left Pedal Arm
Right Pedal
Left Pedal
Disc
Disc Cover
Right Shield
Left Shield
Top Shield
Right Frame Cover
Left Frame Cover
Top Cover
Rear Upright Cover/Receiver
Front Upright Cover
Accessory Tray
Control Board
Board Bracket
Right Rear Leg Cover
Right Front Leg Cover
Left Rear Leg Cover
Left Front Leg Cover
Console
Pulse Sensor
Handgrip
Wheel
Stabilizer Cap
Drive Belt
Crank Arm
M8 Shoulder Screw
Leveling Foot
Latch Bracket
Ramp
Ramp Cover
Ramp Axle
Ramp Axle Bushing
Lift Motor
Upright Axle
Lift Axle
Right Lift Arm
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
34
1
2
1
1
2
2
6
2
1
1
1
4
1
4
1
1
1
1
1
1
1
1
1
1
2
2
1
1
2
2
2
2
2
2
1
4
2
4
4
1
1
2
38
2
1
1
1
2
1
4
Description
Left Lift Arm
Lift Axle Bushing
Long Motor Axle
Short Motor Axle
Bumper
#8 x 25mm Self-tapping Screw
Upright Bushing
M10 x 60mm Bolt
Power Cord
Upright Wire
Eddy Mechanism
M6 x 50mm Screw
Frame Axle
Frame Bushing
Latch Bracket Axle
Latch Bracket Spring
Latch Button
Button Housing
Reed Switch/Wire
Clamp
Crank Hub
Crank
Crank Spacer
Large Pulley
Magnet
Folding Frame Bearing
Idler
Resistance Motor
Lift Roller
Lift Axle Washer
Hairpin Cotter Pin
Lift Axle Screw
Lift Axle Bracket
Motor Spacer
Belt Adjustment Screw
M8 x 25mm Screw
Large Snap Ring
M17 Wave Washer
#8 x 13mm Screw
Right Link Arm
Left Link Arm
Ramp Roller
M4 x 16mm Screw
Link Arm Axle
Ground Screw
M6 Washer
Pivot Screw
Pedal Arm Cap
Idler Bolt
M10 x 120mm Screw
Key No. Qty.
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
1
20
2
6
6
12
4
4
1
2
6
2
2
2
2
4
2
2
2
14
2
1
2
4
1
Description
Key No. Qty.
Anchored Zip Tie
M8 x 16mm Screw
M10 Locknut
M8 x 45mm Bolt
M8 Locknut
Link Arm Bushing
M10 x 25mm Screw
M10 Washer
Frame Wire
M8 x 23.5mm x 1mm Washer
Pivot Axle Cover
M8 Washer
Crank Axle Cover
Magnet Assembly
Pedal Arm Snap Ring
Long Latch Spring
Latch
Latch Spring
Medium Snap Ring
Mushroom Fastener/Screw
Latch Insert
3/8" x 1/2" Flange Screw
Latch Housing
M4 x 42mm Screw
Power Switch
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
*
*
*
*
*
*
*
*
8
2
4
2
2
8
2
1
2
2
2
2
16
4
8
2
2
––
––
––
––
––
––
––
––
Description
M8 x 25mm x 1.5mm Washer
M8 x 30mm Screw
M8 x 25mm Screw
Outer Sleeve Bushing
Small Snap Ring
M8 Split Washer
Short Spring Pin
Frame Cap
Inner Sleeve Bushing
Pulse Wire
Sleeve
Long Spring Pin
M4 x 12mm Screw
M6 x 12mm Screw
M6 Washer
M4 x 25mm Screw
M19 Wave Washer
User·s Manual
Assembly Tool
Resistance Motor Wire
Lift Motor Wire A
Lift Motor Wire B
Blue Wire
Green Wire
White Wire
Note: Specifications are subject to change without notice. For information about ordering replacement parts, see
the back cover of this manual. *These parts are not illustrated.
35
31
126
102
57
36
105
104
93
9
93
93
35
7
88
104
105
57
33
32
102
24
10
93
26
34
93
93
102
93
34
131
131
57
11
93
23
93
102
48
57
131
102
131
5
93
135
88
29
25
57
105
93
6
35
8
102
104
57
126
30
93
EXPLODED DRAWING A
Model No. RBEL07913.0 R0113A
40
40
142
37
37
100
41
93
38
39
60
72
16
4
75
41
125
109
73
75
37
89
95
93
133
101
78
19
59
93
68
93 77
89 85
69
70
138
124
93
2
96
76
97
87
86
93
86 99
74
120
17
27
124
28
76
93
87
89
122
71
61
18
20
93
120
120
40
142 17
39
16
124
124
EXPLODED DRAWING B
Model No. RBEL07913.0 R0113A
108
107
45
46
120
44
38
120
67
66
64
42
110
108
102
107
46
120
64
64
63
53
65
110 102
120
41
120
64
108
107
47
43
83
93
1
84
119
93
56
55
52
93
81
37
49
79
22
51
52
108
107
81
102
102
84
80
54
83
82
80
93
21
82
50
141
58
79
3
36
55
56
93
103
100
93
93
58
141
37
36
EXPLODED DRAWING C
Model No. RBEL07913.0 R0113A
39
112
127
138
132
117
121
138
113
129
126
116
136
62
115
91
140
134
106
13
118
123
137
114
102
128
111
88
106
123
132
117
121
138
114
139
62
106
138
134
137
118
116
12
129
111
126
139
136
98
94
14
130
106
140 92
15
113
126
127
62
139
112
140
128
111
130
106
140
94
98
106
126
115
106
92
102
111
90
88
106
128
111
126
106
EXPLODED DRAWING D
Model No. RBEL07913.0 R0113A
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to
provide the following information when contacting us:
•• the model number and serial number of the product (see the front cover of this manual)
•• the name of the product (see the front cover of this manual)
•• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED
DRAWING near the end of this manual)
LIMITED WARRANTY
IMPORTANT: To protect your fitness equipment with an extended service plan, see page 5.
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. The frame is warranted for a lifetime. Parts are warranted for two (2) years from the date of purchase. Labor is warranted for one (1) year from the date of
purchase.
This warranty extends only to the original purchaser (customer). ICON’’s obligation under this warranty is
limited to repairing or replacing, at ICON’’s option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be preauthorized by ICON. If the product is shipped
to a service center, freight charges to and from the service center will be the customer’’s responsibility. If
replacement parts are shipped while the product is under warranty, the customer will be responsible for a
minimal handling charge. For in-home service, the customer will be responsible for a minimal trip charge.
This warranty does not extend to freight damage to the product. This warranty will automatically be voided
if the product is used as a store display model, if the product is purchased or transported outside the USA,
if all instructions in this manual are not followed, if the product is abused or improperly or abnormally used,
or if the product is used for commercial or rental purposes. No other warranty beyond that specically set
forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special, or consequential damages arising out of or in connection with the use or performance of the product; damages with respect to any economic loss, loss of
property, loss of revenues or prots, loss of enjoyment or use, or costs of removal or installation; or other
consequential damages of any kind. Some states do not allow the exclusion or limitation of incidental or
consequential damages. Accordingly, the above limitation may not apply to the customer.
The warranty extended hereunder is in lieu of any and all other warranties, and any implied warranties of
merchantability or tness for a particular purpose are limited in their scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to the customer.
This warranty provides specic legal rights; the customer may have other rights that vary from state to state.
ICON Health & Fitness, Inc., 1500 S. 1000 W., Logan, UT 84321-9813
Part No. 341624 R0113A
Printed in China © 2013 ICON IP, Inc.
Download PDF