DMP Electronics XTLC Installation guide

INSTALLATION GUIDE
738Z Z-Wave Interface Module
Description
The 738Z Z-Wave Interface Module provides communication with up to
232 Z-Wave devices such as light controls, door locks, and thermostats
To
for residential or small commercial installations. The 738Z easily
Keypad
Bus
connects to the panel’s keypad bus and unifies the control of home
electronics using an integrated wireless network. Now, devices can
be remote controlled from an Apple iPAD/iPhone and Android using
the DMP Virtual Keypad™ application or from any cell devices using
MyAccess™ text commands.
Compatibility
• XT30/XT50 Series panels using software version 109 with Level F hardware support up to 32 Z-Wave devices.
• XT30/XT50 Series panels using software version 110 with Level G hardware support up to 232 Z-Wave devices.
• XTL Series panels using software version 109 with Level D hardware when operating from AC power support up
to 32 Z Wave devices. Battery only operation is not supported.
• XTLC panels using software version 110 with Level E hardware support up to 232 Z-Wave devices.
• XTLN/XTLN-WiFi panels.
• XR150/XR350/XR550 Series panels.
• Mobile applications: MyAccess™ and Virtual Keypad™ App.
What is Included
The 738Z module includes the following items:
• One Model 738Z with housing
• Hardware pack
Control
Panel with
738Z
Office
Installing the 738Z
Kitchen
Dining
Selecting a Location
Garage
A location should be selected that allows communication to
Z-wave devices. The 738Z complies with the Z-Wave standard
of open-air, line of sight transmission distances of 65 feet to
Living Room
the first device. The Z-Wave Light Module acts as a repeater
Foyer
to create more possible transmission routes.
Installing the 738Z
= Z-Wave Light Module Device
The 738Z ships installed in a decorative, high-impact plastic
housing that mounts directly to walls, backboards, or other flat surfaces. For easy installation, the 738Z housing
back and both ends have wire entrances for the four wire connection to the XT panel keypad bus or XTL PROG
connector shown to the right.
PC-0140 Assembly
PROG J5
To connect the wiring of the 738Z to the PROG header of the XTL series panel,
use the PC-0140 Connector Assembly for connection of a Model 300 harness.
When used with the XTLC panel, the 738Z only operates when AC power is
present but is not supported during battery only operation.
Model 300
Harness to 738Z
XTL PCB
Install the module away from large metal objects. Mounting the module on or near metal surfaces impairs
performance.
Programming the Panel
The 738Z Z-Wave module is programmed from the panel’s user menu Z-Wave Setup. When possible, have the Z-Wave
device near the 738Z during setup and programming.
LED Operation
Three LEDs flash to display operation and activity.
• PTX Green LED - Data is being sent to the panel.
• ZTX Green LED - Data is being sent to Z-Wave devices.
• ZRX Yellow LED - Data is being received from Z-Wave devices.
Z-Wave Terminology
Primary Controller: This is the main device used to set up and control your Z-Wave network. There can only be one
primary controller and it can be used to add or delete devices. A primary controller can be a portable device like a
hand-held remote, a static controller (permanently installed & never moved), a Z-Wave enabled PC or a Z-Wave enabled
Ethernet router/bridge.
Secondary Controller: The Z-Wave network supports multiple controllers so that additional Z-Wave remote controllers can
be used throughout the home. If the secondary controller is the same brand and model as the primary, it will have all the
same capabilities as the primary with one exception; the secondary controller can not be used to add or delete devices.
Home Control Network: The controllers and every Z-Wave device added with the primary controller are linked together
into a wireless network. Each device in the network has a unique address assigned to it and cannot be activated by a
neighbor’s Z-Wave controller.
Light/Node/Device: Node is the technical term used to describe a Z-Wave device in a home control network. Please note
that the terms “Node,” “Device,” and “Light” all refer to an individual Z-Wave enabled device and are interchangeable
within the context of these instructions.
Z-Wave Certification
• The 738Z is a Z-Wave Security enabled device.
• The 738Z can be added to an existing network as a secondary controller using the Transfer process and selecting secondary
on the primary controller. See Transfer Controller (XFER) in the Z-Wave Setup section of the control panel User Guide.
• The 738Z is compatible with Z-Wave devices from all manufacturers.
• The 738Z can perform a Factory Default Reset by initializing defaults in the panel programming menu.
FCC Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications made by the user and not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
To comply with RF exposure requirements, a minimum distance of 20cm must be maintained between the antenna and all persons.
Industry Canada Information
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Frequency Range 908 MHz
Dimensions 4.5” W x 2.75” H x 1.75” D
ColorWhite
Housing Material
Flame retardant ABS
Certifications
FCC Part 15 ID: CCKPC0137
Industry Canada:
5251A-PC0137
Z-Wave Certification: ZC08-14080002
Z-Wave GE Light Control Modules with and without dimmer
Such as the DMP Z-45602 and Z-45603
Z-Wave Kwikset and Schlage Deadbolt and Lever Locks
Such as the DMP Z-99100
Z-Wave Trane or 2-GIG Thermostats
Such as the DMP Z-TSEMT400BB3X or 2-GIG Z-STAT
Z-Wave Portable Controllers
Such as the GE 45601
Z-Wave Toggle Style Auxiliary Switch
Such as the DMP Z-45604
Z-Wave In-Wall Dimmer Switch
Such as the DMP-Z45605
Z-Wave In-Wall Toggle Style On/Off Relay Switch
Such as the DMP Z-45606
Z-Wave Garage Door Controller
Such as the DMP Z-GD00Z-4
800-641-4282
INTRUSION • FIRE • ACCESS • NETWORKS
www.dmp.com
2500 North Partnership Boulevard
Designed, Engineered and
Assembled in the USA
Springfield, Missouri 65803-8877
15121
Device Compatibility
Power Requirements
Operating Voltage8.0 to 14 VDC
Current Draw
35mA
LT-1209 © 2015 Digital Monitoring Products, Inc.
Specifications