•Dual display of wind speed
and temperature
•7 units selectable: m/s, km/h,
ft/min, knots, mph, °C, °F
•12 level beaufort scale
indicator
•Wind chill indicator
•Special fan structure design,
can detect startup wind
speed as lower as 0.1m/s
•Max /Avg modes, auto power
off, user-friendly interface
OPERATOR’S MANUAL
ORDER CODE: OXD-312-5643D
CZ HU PL SK TH cromwell.co.uk
SAFETY INFORMATION
1. Please check the Anemometer before using
and beware of any damage or abnormal
phenomenon. If you find the case is
damaged or the LCD shows nothing, or you
consider that the Anemometer could not
work properly anymore, please stop using it.
2. Observe the operating instructions
while measuring.
3. Do not open the Anemometer at will or
change internal wiring.
4. When the LCD displays “ ”, replace
the batteries. Remove the battery if the
Anemometer is not used for a long time.
5. Do not store or use the Anemometer in high
temperature, high humidity, flammable,
combustible, or strong electromagnetic
environment.
6. Please use soft cloth and neutral detergent
to clean the case. Do not use solvent.
GENERAL INFORMATION
• LCD display: 4-bit LCD display. The
displayed maximum is 9999.
• Overload indication: When the
wind speed is over 45m/s or the
temperature is lower than -10°C
or higher than 50°C, “OL” will be
displayed.
• Low battery display:
Batteries
should be replaced.
• Sampling rate: 2/s
• Sensor type: Magnetic induction type
wind speed sensor and NTC negative
temperature coefficient sensor.
• When the temperature is lower than
0°C and the wind speed is over 5m/s,
the meter shows “WINDCHILL”.
• Power requirement: 1.5V batteries
(AAA) x3
• Product size: 160 x 50 x 28mm
• Weight: 118g
ENVIRONMENT SPECIFICATION
• Altitude height: 2000m
• Pollution level: 2
• Working temperature and humidity:
0°C -40°C (not greater than 80% RH)
40°C -50°C (not greater than 45% RH)
• Storage temperature and humidity:
-20°C ~60°C (not greater than 75% RH)
ELECTRICAL SPECIFICATIONS
• Accuracy: Wind speed: ±5% rdg + 0.5
Temperature: ±2°C
• Environment temperature: 23°C ±5°C
• Environment humidity: ≤80% RH
GENERAL MAINTENANCE
Warning: To avoid affecting device
accuracy or damage to the Anemometer
do not open the Anemometer.
• Maintenance and service of the
Anemometer should be accomplished
by professional personnel or
designated maintenance department.
• Clean the case with a dry cloth
periodically, detergent with abrasive
or solvent composition should not be
used.
TECHNICAL SPECIFICATION
MINI ANEMOMETER
THE ENVIRONMENT
PRODUCT FEATURES
DISPLAY INTERFACE
KEY FUNCTIONS AND SETUP
ON/OFF:
Press once to start up and press again to
power off.
Note: Product’s auto power off feature
can be disabled: Press and hold “HOLD”
and then press “ON/OFF” key to enable/
disable auto power off, LCD will display
“APO OFF” to indicate status.
UNIT: Unit conversion key:
Press this key and the wind speed value
cycles m/s, km/h, ft/min, knots, and
mph. Keep pressing the key and the
temperature unit changes between
°C and °F.
MAX/AVG:
Pressing this key can select maximum,
average and normal value measurement;
select maximum and the Anemometer
will always show the maximum reading;
select average and the Anemometer will
always show the average reading.
HOLD/BL:
HOLD: Press this key once to hold the
measurement; press this key again to
exit data hold and continue normal
measurement.
BL: Keep pressing this key to turn on
the backlight. Press again to turn off
backlight.
BATTERY INSTALLATION
AND REPLACEMENT
• The meter uses 3 x AAA 1.5V batteries.
Please see figure below for steps of
battery installation and replacement.
• Slide the panel down, open the
battery cover open in the direction of
the arrow and remove the batteries.
Install new batteries in accordance of
polarity indications.
• Please use batteries of same type.
• Close the cover tightly after installing
new batteries.
Always dispose of unwanted tools, accessories and packaging
materials in an environmentally friendly manner.
In observance of European Directive on Waste Electrical
and Electronic Equipment (WEEE) and its implementation
in accordance with national law, electrical goods that have
reached the end of their life must be collected separately and
returned to an environmentally compatible recycling facility.
Do not dispose of electrical goods with domestic waste
materials as inappropriate disposal may cause potential
hazards to the environment and human health.
For further information, please contact your local authority
or the retailer from whom you purchased the product.
QUALITY GUARANTEE & WARRANTY
OXFORD PRECISION products carry a one year manufacturer’s warranty.
OXFORD PRECISION products are designed & manufactured
to the highest standards & specifications.
Assuring the quality and performance required by all sectors of industry.
OXFORD PRECISION products are fully guaranteed
against faulty materials & workmanship.
Should they be found to be defective, they will either be repaired or
replaced free of charge (fair wear and tear and/or misuse excepted).
Please retain supplier invoice as proof of purchase.
DECLARATION OF CONFORMITY
We hereby certify that the OXFORD MINI ANEMOMETER
(ORDER CODE: OXD-312-5643D)
Complies with all the relevant provisions of the
EMC Electromagnetic Compatibility Directive 2014/30/EU
Standards Applied: EN61326-1:2013, EN61326-2-2:2013
RoHS2 Restriction of Hazardous Substances Directive 2011/65/EU
Signed:
Date: September 2019
Name: Toni Johnson
Position: Compliance Director.
OXFORD PRECISION
P.O. Box 14, Wigston, Leicester,
England, LE18 1AT.
">