Z/ON
Z/ON
ABS
ABS
Z/ON
Z/ON
Z/ON
Z/ON
ABS
ABS
Functions continued
ABS
7) Measure run-out of a high speed workpiece
C
C
The indicator may record max. and min. value automatically.
Press
key for a short
C
R
R
duration then the memory can be erased, the LCD will-CCCdisplay -CCC- -CCC, and will record
again.
R
C
Press R key for a short duration
to check the run-out. When RAN and
are displayed the
-CCCvalue shown on LCD is the
max. runout. Press R key
for a short durationR again. R
C
R
R be displayed and the value on LCD is the min.
will
runout. Now press R key again.
C
-CCCR
-CCCwill be displayed. Now
both max. and min.
will
be displayed. Press R key for a short
R
R
duration
once more, the indicator will resume to normal measuring
mode
(display).
R
R R
R
R
R
R
R
C
R
R
R
R
in/mm
C
R
OXD-331 SERIES OPERATOR’S MANUAL
-CCC-C
R
C
-CCC-
-CCC-
Digital Indicators
-CCC-
R
R
R
R
• Inch/Metric measurement
• Absolute Measuring/Relative reading
in/mm
• Zero Setting
in/mm
• +/- Display
• Auto/Manual Power off
• Preset a Value
in/mm
• Measure run out of a high speed work piece
R
R
push
in/mm
contact point
R
ABS
R
ABS
in/mm
push
R
push
contact point
Z/ON
Z/ON
contact point
Z/ON
R
R
R
ABS
in/mm
in/mm
push
1. Avoid shocks, impact, dropping etc. This will effect the precision & accuracy as well
push
as appearance.
contact point
in/mm
push
2. Do not remove output connector lid unless using output interface.
in/mmDoing so could damagecontact
3. Output end should never be in contact with metal.
your point
indicator.
4. Do not allow any part of the digital indicator to come into contact with electrical
ABS
voltage, as this will damage the circuitry.
R
R
ABS
in/mm
C
contact point
Attention:
You may stay with one mode only, say min. runout or max. runout or max. & min.
runout. C key can be pressed in any mode to erase the memory.
in/mm
8) Manual/Auto Power Off
C
When the indicator is powered off, press and hold the ABS key and press Z/On key, the
indicator ABS
will get
into Manual/Auto Power off Setting mode. “H” means Hand (manual)
ABS
power off. The indicator is powered off when Z/on button is pressed for a long duration.
“A” represents
Auto power off. If testing rod stays still and no key is pressed for 4 hours,
in/mm
the
Z/ON indicator will be powered off automatically. Short press Z/On key to save the setting
and quit Manual/Auto Power off Setting mode.
Z/ON
Z/ON
ABS
ABS
Z/ON
in/mm
in/mm
Z/ON
in/mm
ABS
ABS
0-12.7MM/0.5" DIGITAL INDICATOR 0.01MM/0.0005"
ORDER CODE:
OXD3316030K
MEASURING RANGE
0-12.7mm/0.5"
READING
0.01mm/0.0005"
in/mm
LCD DISPLAY
7.5mm
RESPONSE SPEED
0.5m/s.
Z/ON
STORAGE TEMPERATURE
-10~60 DEGREE CENTIGRADE
Maintenance
ABS
ABS
ABS
Z/ON
contact point
C
push
contact point
C
push
ABS
in/mm
Service & repair
in/mm
R
Z/ON
R
R
Z/ON
contact point
R
R
push
Z/ON
A comprehensive repair and service
facility is available through your local
ABS
KENNEDY TOOLS agent.
in/mm
0-12.7MM/0.5" M/F INDICATOR 0.001MM/0.00005"
ABS
ORDER CODE:
OXD3316040K
Z/ON
MEASURING RANGE
0.12.7mm/0.5"
READING
0.001mm/0.00005"
ABS
LCD DISPLAY
7.5mm
RESPONSE SPEED
0.5m/s.
Z/ON
STORAGE TEMPERATURE
-10~60 DEGREE CENTIGRADE
in/mm
R
in/mm
contact point
push
R
in/mm
R
in/mm
C
ABS
1.Clean the indicator housing, the stem and the testing rod with soft oil-free cloth.
If it’s very dirty, put some neutral cleaner on the cloth.
2. The hole that holds the indicator stem should be 8H6.
3. Clean the indicator after using.
4. The indicator should be taken apart by professionals only in case of serious damage.
5.Replace the battery when LCD turns dim, the figures are not clear or the indicator
in/mm
cannot be turned on.
Z/ON
ABS
in/mm
ABS
in/mm
Z/ON
ABS
R
R
Z/ON
R
in/mm
in/mm
Specifications
R
R
R
Features
Safety
R
R
in/mm
in/mm
Inch
Metric
Functions continued
Identification
4) Changing between Absolute Measuring and Relative Measuring
push
This change can be achieved by pressing ABS key for a short duration.
When ABS is
contact
displayed the absolute value is on
the screen. Press ABS key
for point
a short duration, then
in/mm
ABS will disappear on the screen and the status will be changedin/mm
to Relative measuring
and the value on the screen will be “Zero”. Then you may test the workpiece and read
Inch
the deviation
from “Zero” directly. Press the ABS key again, the status will be changed to
Absolute Reading again and ABS will reappear.
in/mm
11
6
7
12
13
14
15
Z/ON
in/mm
Metric
5
4
Z/ON
ABS
10
8
Z/ON
9
2
in/mm
18
17
16
in/mm
Metric
Metric
Absolute Measuring
5) Change +/-
3
1
7 Run Key
8 In/mm key
9 ABS/PRESET key
10 Z/ON key
11 Display Metric
12 Display Inch
Absolute Measuring
13 Display Preset
14 Display Graduation
15 Display ABS mode
16 Display
Low voltage
in/mm
17 Display Max. Value
18 Display Min. Value
contact point
in/mm
Relative Measuring
push
push in/mm
contact point
in/mm
push
in/mm
contact point
in/mm
R
push
push
R
contact point
contact point
in/mm
R
R
in/mm
in/mm Z/ON
in/mm
R
push
in/mm
in/mm
Z/ON
R
contact point
in/mm
contact
ABSpoint
Z/ON
R
Press
key until “+” code blinks. When “+” stops blinking ABS
and disappears, push the
R
push
contact point, the valuein/mm
will be plus.
push
push
contact point
in/mm
contact point
C
in/mm
push
C
contact
point
6) Preset a value
in/mm
ABS
contact point
in/mm
When the indicator is in “ABS” and “metric” mode, press and
hold for 2 secondsR ABS key to get
R
in/mm
into “Presetting a value” mode. The number that is blinking is the one that can be changed.
Z/ON key for a short
Press
for a short duration, then the number changes
from
0 to 9.R Pressin/mm
Z/ON
push
ABS
in/mm
ABS
duration then the blinking numberin/mm
will move one position contact
left. In
thisZ/ON
way all the
numbers and ABS
point
ABS
ABS
ABS
+/- can be set. When the value is correctly
set, press
key for a long duration to save the
ABS
preset value and quit “Presetting
a value” mode. Now the indicator will getABSinto ABS mode.
in/mm
push
contact point
in/mm
in/mm now the real
Please note that
absolute Zero point
is with the value presetted.C If Z/ON key is
in/mm
Inch
pressed
and held the Z/ON
presetted value willZ/ONbe erased and the absolute Zero will be displayed as
Absolute
Measuring
Measuring
ABS value
“0” and the indicator will quit “Presetting a value”Relative
mode. Please
note that the presetted
ABS
cannot be higher than 99. ABS
in/mm
1. On/Off
Inch
Metriccompartment
a) Fit a new batteryZ/ON
into the battery
b) Press Z/ON key forZ/ON
a short
duration,
the
indicator
will
be
switched
on
Z/ON
c) Press and hold Z/ON key, the indicator will be switched off.
Z/ON
Z/ON
Z/ON
2. Zero setting
Z/ON
Z/ON
Z/ONfor a short duration, the screen
a) In ABS Mode (ABS is shown on the screen),
ABS
Z/ONpress
will show “0” or you may say zero point is set there.
b) When the indicator is turned from ABS mode to Relative mode, the screen will show
zero and you may achieve relative measuring.
c) When the indicator is in “REL” mode, zero cannot be reset.
3. Inch/metric
in/mm key for a short duration.
Inch/metric switching can be achieved by pressingin/mm
If mm is displayed, the value is in metric.in/mm
If inch isin/mm
displayed, the value is in inch.
in/mm
Metric
Z/ON
Z/ON
ABS
ABS
Z/ON
ABS
in/mm
in/mm
ABS
Z/ON
ABS
in/mm
Metric
Relative Measuring
in/mm
ABS
Metric
Metric
in/mm
in/mm
ABS
Inch
Absolute
Measuring
Absolute
Measuring
ABS
Relative
RelativeMeasuring
Measuring
C
-CCC-
ABS
ABS
ABS
Z/ON
ABS
ABS
Z/ON
in/mm
ABS
Z/ON
Z/ON
Z/ON
Z/ON
ABS
ABS
in/mm
ABS
ABS
Inch
Inch
Inch
Z/ON
Z/ON
ABS
ABS
Z/ON
Z/ON
ABS
in/mm
in/mm
Z/ON
Z/ON Z/ON
Z/ON
in/mm
in/mm
ABS
ABS
in/mm
ABS
Absolute Measuring
Z/ON
ABS
Z/ON
Z/ON
Metric
push
contact point
pushABS
in/mm
in/mm
in/mm
Z/ON
in/mm
Functions
Inch
Inch
Relative Measuring
Press in/mm key until “-” code blinks. When “-” stops blinking and disappears, push the
R
in/mm
contact point, the value will be minus.
in/mm
ABS
1 Anvil
2 Stem
3 Battery compartment
4 Rear cover
5 LCD
6 Clear key
in/mm
in/mm
ABS
C
-CCC-
R
R
Z/ON
Z/ON
R
ABS
C
C
R
R
">