Panametrics DigitalFlow XGS868i Programming Manual

DigitalFlow™ XGS868i
Panametrics Steam Ultrasonic Mass Flow Transmitter
(1 & 2 Channel)
Programming Manual
panametrics.com
BH059C31 EN J
DigitalFlow™ XGS868i
Panametrics Steam Ultrasonic Mass Flow Transmitter
(1 & 2 Channel)
Programming Manual
BH059C31 H
March 2024
panametrics.com
Copyright 2024 Baker Hughes company.
This material contains one or more registered trademarks of Baker Hughes Company and its subsidiaries
in one or more countries. All third-party product and company names are trademarks of their respective
holders.
[no content intended for this page]
ii
Preface
Services
Panametrics provides customers with an experienced staff of customer support personnel
ready to respond to technical inquiries, as well as other remote and on-site support needs. To
complement our broad portfolio of industry-leading solutions, we offer several types of
flexible and scalable support services including: Training, Product Repairs, Service Agreements
and more.
Please visit https://www.bakerhughes.com/panametrics/panametrics-services for more
details.
Typographical Conventions
Note:
These paragraphs provide information that provides a deeper understanding of the situation, but is not
essential to the proper completion of the instructions.
IMPORTANT: These paragraphs provide information that emphasizes instructions that are essential to proper setup
of the equipment. Failure to follow these instructions carefully may cause unreliable performance.
CAUTION!
This symbol indicates a risk of potential minor personal injury and/or severe damage to
the equipment, unless these instructions are followed carefully.
WARNING! This symbol indicates a risk of potential serious personal injury, unless these
instructions are followed carefully.
Safety Issues
WARNING! It is the responsibility of the user to make sure all local, county, state and national codes,
regulations, rules and laws related to safety and safe operating conditions are met for
each installation.
Attention European Customers!To meet CE Mark requirements for all units intended for use in the EU,
all electrical cables must be installed as described in this manual.
iii
Preface
Auxiliary Equipment
Local Safety Standards
The user must make sure that he operates all auxiliary equipment in accordance with local codes, standards,
regulations, or laws applicable to safety.
Working Area
WARNING! Auxiliary equipment may have both manual and automatic modes of operation. As
equipment can move suddenly and without warning, do not enter the work cell of this
equipment during automatic operation, and do not enter the work envelope of this
equipment during manual operation. If you do, serious injury can result.
WARNING! Make sure that power to the auxiliary equipment is turned OFF and locked out before
you perform maintenance procedures on this equipment.
Qualification of Personnel
Make sure that all personnel have manufacturer-approved training applicable to the auxiliary equipment.
Personal Safety Equipment
Make sure that operators and maintenance personnel have all safety equipment applicable to the auxiliary
equipment. Examples include safety glasses, protective headgear, safety shoes, etc.
Unauthorized Operation
Make sure that unauthorized personnel cannot gain access to the operation of the equipment.
Environmental Compliance
Waste Electrical and Electronic Equipment (WEEE) Directive
Panametrics is an active participant in Europe’s Waste Electrical and Electronic Equipment (WEEE) take-back initiative,
directive 2012/19/EU.
The equipment that you bought has required the extraction and use of natural resources for its production. It may
contain hazardous substances that could impact health and the environment.
In order to avoid the dissemination of those substances in our environment and to diminish the pressure on the
natural resources, we encourage you to use the appropriate take-back systems. Those systems will reuse or recycle
most of the materials of your end of life equipment in a sound way.
The crossed-out wheeled bin symbol invites you to use those systems.
If you need more information on the collection, reuse and recycling systems, please contact your local or regional
waste administration.
iv
Contents
Chapter 1. Programming Site Data
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Programming Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
The XGS868i Enclosure Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Activating a Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Entering System Data for the Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.5.1 Accessing the Channelx-System Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.5.2 Selecting Volumetric Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.5.3 Selecting Totalizer Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.5.4 Selecting Mass Flow Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Entering Transducer and Pipe Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.6.1 Special Transducers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.6.2 Pipe Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Entering Zero Cutoff and Setting Up Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.7.1 Zero Cutoff Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.7.2 Assume Saturation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.7.3 Steam Input Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.7.4 Temperature Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
1.7.5 Base Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
1.7.6 Pressure Input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
1.7.7 Base Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
1.7.8 Low Pressure Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
1.7.9 Quality Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Entering Setup Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1.8.1 Setting Transducer Signal Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1.8.2 Initializing Setup Parameters - Default Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
1.8.3 Setting Response Time - V Averaging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
1.8.4 Using Advanced Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Entering Global Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
1.9.1 Entering Global System Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
1.9.2 Setting Up Inputs and Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
1.9.3 Configuring the Communications Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
1.9.4 Requesting Parameters Using MODBUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
1.9.5 Activating Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Exiting the User Program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Chapter 2. Displaying Data
2.1
2.2
2.3
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Displaying Data with the LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
2.2.1 Adjusting LCD Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
2.2.2 Programming the LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Displaying Data on a Computer Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
2.3.1 Preparing for PanaView Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
2.3.1 The Text Display Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
2.3.2 The Graphing Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
2.3.3 Displaying Transducer Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Chapter 3. Logging Data
3.1
3.2
3.3
3.4
3.5
3.6
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
The Data Logging Option Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Logging via PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Creating Meter Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
3.4.1 Creating a Standard Meter Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
3.4.2 Creating an Error Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
3.4.3 Checking Log Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
3.4.4 Stop Logging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Creating PC Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Viewing Meter Log Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
DigitalFlow™ XGS868i Programming Manual
v
Contents
3.7
Viewing PC Log Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
4.1
Data Types for Printing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
5.1
5.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Clearing the XGS868i’s Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
5.2.1 Clearing Site Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
5.2.2 Clearing Log Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
5.2.3 Clearing the Totalizers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Chapter 4. Printing Data
Chapter 5. Clearing Data
Appendix A. Menu Maps
Appendix B. Data Records
B.1
B.2
B.3
Available Option Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Option Cards Installed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Setup Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
C.1
C.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
Programming with PanaView™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
C.2.1 Preparing for PanaView Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
C.2.2 Setting Up the Communications Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
C.2.3 Setting up Ethernet Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
C.2.4 Modifying Ethernet Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Adding the XGS868i. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
Entering the User Program using PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
Entering Data in the Channel Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
C.5.1 Selecting the Channel Measurement Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
C.5.2 Entering Data in the Channel System Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
C.5.3 Entering Pipe Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
C.5.4 Entering Input/Output Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
C.5.5 Entering Setup Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Entering Data in the Global Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
C.6.1 Entering Global-System Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
C.6.2 Setting Up Inputs and Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
C.6.3 Entering Communications Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Exiting the Site Edit Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Saving Site Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
C.8.1 Saving Current Site Data to the Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
C.8.2 Saving New Site Data to the XGS868i. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
C.8.3 Saving a Site to the PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
C.8.4 Clearing a Site from the Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
C.8.5 Saving Site Data in Text Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Appendix C. Programming the XGS868i Using PanaView™
C.3
C.4
C.5
C.6
C.7
C.8
Appendix D. PanaView Menu Maps for the XGS868i
Appendix E. Foundation Fieldbus Communications
E.1
E.2
E.3
E.4
E.5
E.6
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Configuration Utility Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Selecting the Desired Measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Selecting Units for AI Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Resetting Instrument Totalizers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Function Block Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Appendix F. Foundation Fieldbus Tables
vi
DigitalFlow™ XGS868i Programming Manual
Chapter 1. Programming Site Data
Chapter 1.
1.1
Programming Site Data
Introduction
The Model XGS868i flow transmitter must be properly installed and programmed, as described in the Startup Guide,
before it can provide accurate flow rate measurements. After completing the installation and initial setup, use this
chapter to program the advanced features of the Model XGS868i’s Keypad Program.
Step-by-step programming instructions are presented in this chapter. Also, as a programming aid, a complete set of
menu maps for the XGS868i are included in Appendix A, Menu Maps. The specific figure numbers will be referenced
throughout this chapter, as required.
Refer to the appropriate section for a discussion of the following Keypad Program features.
•
•
•
•
•
•
•
•
Channelx-ACTIV - activate one or both channels and Scroll to the desired measurement method.
Channelx-SYSTM - enter the individual channel parameters.
Channelx-PIPE - enter the pipe geometry and other parameters.
Channelx-I/O - set up the inputs and outputs.
Channelx-SETUP - set the signal limits, response times and mass flow status.
Global-SYSTM - Scroll to system units (English or metric).
Global-I/O - set up error handling, option cards and the display.
Global-COMM - set the serial port parameters.
Note:
The “x” in CHx represents the channel number. If you are using a 1-Channel meter, only CH1 will appear.
To get the XGS868i up and running as quickly as possible you must, as a minimum, activate the channel(s), enter the
channel and global system data and the pipe parameters. The Procedure Options section at the end of each menu
will help you in programming the required (quick startup) and optional data.
Note:
In this manual, only the programming of Channel 1 will be described. To program Channel 2 of a 2-channel
meter, simply repeat the same procedure presented for Channel 1.
DigitalFlow™ XGS868i Programming Manual
1
Chapter 1. Programming Site Data
1.2
Programming Methods
You can program the XGS868i via either the keypad on the lower part of the glass enclosure, or PanaView™, a
PC-based, non-resident software program that communicates with the XGS868i via its RS232 serial port. PanaView
supplements basic XGS868i functions with several additional capabilities. With PanaView, you can:
•
load and save site file data
•
create and save graph and log files
•
display text output and graphs of live measurement data
•
create custom templates for displaying text, graph and log data
•
interface with multiple Panametrics Measurement & Control instruments.
Although the actual displays differ somewhat, the general procedures are the same for all three programming
methods. This chapter provides detailed programming instructions for use with the keypad. If you are using
PanaView™, see Appendix C, Programming the XGS868i via PanaView™, and/or the PanaView™ User’s Manual
(910-211) for detailed instructions.
IMPORTANT: This manual is for instruments using software version Y4AS or later.
2
DigitalFlow™ XGS868i Programming Manual
Chapter 1. Programming Site Data
1.3
The XGS868i Enclosure Keypad
Keypad Program
Along with the 2-line, 16-character LCD, the XGS868i includes a 6-key magnetic keypad. The decal cutout for each
key contains a hall effect sensor, pushbutton switch and visible red LED. The magnetic wand used to activate a
magnetic key is found attached to the meter chassis below the front panel. An operator activates the key by pressing
the magnetic wand up to the glass lid over the desired key. The LED will light indicating a successful key press.
Note:
The pushbutton switch will also act as a key press but is done with the glass lid open. Do not use the
pushbutton switch in a hazardous area where the lid needs to be installed.
Use the magnetic keypad to navigate through the user program. The menu map may be followed in sequence, or the
four arrow keys may be used to scroll through the prompt screens. Figure 1 shows the front of the XMT868i, with
magnetic keypad and magnetic wand.
#
ESCAPE
DigitalFlowTM XGS868i
ENTER
Magnetic Wand
Figure 1: XGS868i Magnetic Keypad and Wand
IMPORTANT: The XGS868i’s keypad permits programming of the instrument through the glass faceplate without
removing the cover. Thus, all programming procedures may be performed while the unit is installed in a
hazardous area.
Six keys on the keypad enable users to program the XGS868i:
•
[Enter] - confirms choice of a specific option and data entry within the option
•
[Escape] - allows users to exit from a specific option without entering unconfirmed data
•
[] and [] - enable users to highlight a specific window in the display option or to scroll through a list of
options (parameters, letters, and numbers 0-9 as well as the negative sign and decimal point) in a menu
•
[] and [] - enable users to scroll to a specific option, among choices in an option, or to a character in a text
entry.
DigitalFlow™ XGS868i Programming Manual
3
Chapter 1. Programming Site Data
1.3
The XGS868i Enclosure Keypad (cont.)
When you power up the XGS868i, the display first shows the model and software version:
Panametrics
XGS868i Y4AS.STD
The meter then starts to display measured parameters.
CH1
VEL
10.00
E1
Ft/s
To enter the Keypad Program, press the [Escape] key, followed by the [Enter] key, and the [Escape] key again. Each
successive key must be entered within 10 seconds of the prior key.
As a guide in following the programming instructions in this chapter, the relevant portions of the Model XGS868i
menu map have been reproduced in Figure 28 on page 71 and Figure 29 on page 72. Proceed to the following
sections to enter data in the Channel or GLOBL menus.
IMPORTANT: If the keypad has not been pressed for 10 minutes, the XGS868i exits the Keypad Program and returns to
displaying measurements. The meter retains any configuration changes that were confirmed with the
[Enter] key, and restarts as if the operator had completed the programming cycle.
4
DigitalFlow™ XGS868i Programming Manual
Chapter 1. Programming Site Data
1.4
Activating a Channel
The Channelx-ACTIV submenu permits selection of the desired measurement method. In addition, it is used to
activate/deactivate one or both of the channels in a 2-Channel Model XGS868i.
While following the programming instructions, refer to Figure 28 on page 71. To access the Channelx-ACTIV submenu:
1.
2.
3.
4.
In the Keypad Program, scroll to PROG and press [Enter].
In the PROG menu, scroll to CH1 or CH2 and press [Enter].
In the Channel PROGRAM menu, scroll to ACTIV and press [Enter].
Scroll to Burst to activate the channel/path, and press [Enter].
Note:
5.
Burst is automatically selected for a 1-Channel meter.
Scroll to one of the measurement methods described below and press [Enter].
• Skan Only is the preferred technique for locating the acoustic signal and for high velocity measurements. It is
more robust in a noisy environment than the Measure technique.
• Skan/Measure is the preferred technique to use for low velocity measurements.
If Skan Only is selected at the above prompt, the meter uses this technique exclusively. However, if Skan/Measure is
selected, the meter uses Skan Only to find the acoustic signal and then tries to use the Skan/Measure technique for the
actual measurement.
Note:
To change the Skan Only and Skan/Measure parameters, see the Signal submenu section on page 14 of this
chapter.
Procedure Options
After completing the above step, the XGS868i returns to the Channel PROGRAM window. Do one of the following:
•
To continue entering “quick startup” data, proceed to Step 3 in the following section.
•
To continue regular programming, refer to Appendix A, Menu Maps, to navigate to the desired menu.
•
To leave the Keypad Program, press [Escape] twice.
DigitalFlow™ XGS868i Programming Manual
5
Chapter 1. Programming Site Data
1.5
Entering System Data for the Channel
The Channelx-System submenu is used to enter system parameters for the channel. While following the
programming instructions, refer to Figure 28 on page 71.
1.5.1
1.
Accessing the Channelx-System Submenu
In the Keypad Program, scroll to PROG and press [Enter].
2.
In the PROG menu, scroll to CH1 or CH2 and press [Enter].
4.
Use the arrow keys to enter the desired Channel Label (up to 5 characters) and press [Enter].
3.
5.
In the Channel PROGRAM menu, scroll to SYSTM and press [Enter].
Use the arrow keys to enter the desired Site/Channel Message (up to 21 characters) and press [Enter].
1.5.2
Selecting Volumetric Units
1.
Scroll to the desired Volumetric Units for the flow rate display and press [Enter]. Available units are listed in Table 1
below.
2.
Scroll to the desired Volumetric Time units for the flow rate display and press [Enter].
3.
Scroll to the desired number of Vol. Decimal Digits (digits to the right of the decimal point in the volumetric flow
rate display) and press [Enter].
Table 1: Available Volumetric/Totalizer Units
English
Metric
1.5.3
ACF = Actual Cubic Feet
ACM = Actual Cubic Meters
KACF = Thousands of ACF
KACM = Thousands of ACM
MMACF = Millions of ACF
MMACM = Millions of ACM
SCF = Standard Cubic Feet
SCM = Standard Cubic Meters
KSCF = Thousands of SCF
KSCM = Thousands of SCM
MMSCF = Millions of SCF
MMSCM = Millions of SCM
Selecting Totalizer Units
1.
Scroll to the desired Totalizer Units for the totalized flow rate display and press [Enter]. Available units are listed in
Table 1.
2.
Scroll to the desired number of Tot Decimal Digits (digits to the right of the decimal point in the totalized flow rate
display) and press [Enter].
3.
Do one of the following:
• If MASS FLOW is ON, proceed to Selecting the Mass Flow Units on the following page.
• If MASS FLOW is OFF, the meter returns to the Channel PROGRAM. Go to Procedure Options on page 5.
Note:
6
To activate mass flow, refer to page 19.
DigitalFlow™ XGS868i Programming Manual
Chapter 1. Programming Site Data
1.5.4
1.
Selecting Mass Flow Units
Scroll to the desired Mass Flow units for the flow rate display and press [Enter]. The available units for this prompt
are determined by the selection made at System Units (see Table 2).
Table 2: Available Mass Flow Units
English
Metric
LB = Pounds
KG = Kilograms
KLB = Thousands of LB
TONN = Metric Tons (1,000 KG)
MMLB = Millions of LB
TONS = Tons (2,000 LB)
2.
Scroll to the desired Mass Flow Time units for the mass flow rate display and press [Enter].
3.
Scroll to the desired number of Mdot Decimal Digits (digits to the right of the decimal point in the mass flow rate
display) and press [Enter].
4.
Scroll to the desired Mass (Totalizer) units for the totalized mass flow rate display and press [Enter]. The available
units for this prompt are determined by the selection made at the System Units prompt.
5.
Scroll to the desired number of Mass Decimal Digits (digits to the right of the decimal point in the totalized mass
flow rate display) and press [Enter].
Procedure Options
After completing the steps on the previous page, the XGS868i returns to the Channel PROGRAM window. Do one of the
following:
•
To continue entering “quick startup” data, continue to Step 1 in Entering Transducer and Pipe Parameters on the
next page.
•
To continue regular programming, refer to Appendix A, Menu Maps, to navigate to the desired menu.
•
To leave the Keypad Program, press [Escape] twice.
DigitalFlow™ XGS868i Programming Manual
7
Chapter 1. Programming Site Data
1.6
Entering Transducer and Pipe Parameters
Enter the transducer and pipe parameters via the PIPE submenu. While following the programming instructions, see
Figure 28 on page 71.
1.
2.
From the Channel PROGRAM menu, scroll to the PIPE option and press [Enter].
The first prompt asks for the Transducer Number.
• For a standard transducer, use the arrow keys to enter the number engraved on the transducer head, and
press [Enter].
• If there is no number engraved on the transducer head, press the right arrow key to scroll to the STD option, and
use the up and down arrow keys to change to SPEC. Then use the arrow keys to enter an assigned number
(from 91 to 99), and press [Enter].
IMPORTANT: Special transducers have no engraved number on the head and are rarely used. Examine the
transducer head carefully for a number.
•
If you entered the number for a standard transducer, proceed to the Pipe OD prompt in step 5.
•
If you entered the number for a special transducer, proceed to step 3 below.
1.6.1
Note:
3.
For special transducers, Panametrics Measurement & Control will supply a transducer data sheet with
programming information.
Scroll to the transducer Frequency (supplied by the factory) and press [Enter].
Note:
4.
Special Transducers
The frequency is required to transmit an excitation voltage at the transducer’s natural frequency.
Enter the special transducer Tw (time delay) value (supplied by the factory) and press [Enter].
Tw is the time required for the transducer signal to travel through the transducer and its cable. This time delay
must be subtracted from the transit times of the upstream and downstream transducers to ensure an accurate
measurement.
8
DigitalFlow™ XGS868i Programming Manual
Chapter 1. Programming Site Data
1.6.2
Pipe Data
If either a standard or a special transducer is being used, the programming sequence should be rejoined at this
point.
1.
To select the appropriate Pipe OD Unit type from the list shown in Table 3 below, scroll to the right side of the
screen, and use the up and down arrow keys to step through the list. Press [Enter]. Then use the arrow keys to
enter the known pipe outside diameter or circumference on the left side and press [Enter].
Obtain the required information by measuring either the pipe outside diameter (OD) or circumference at the
transducer installation site. The data may also be obtained from standard pipe size tables found in Sound
Speeds and Pipe Size Data (914-004).
Table 3: Available Pipe Size Units
English
Metric
2.
inches
mm = millimeters
feet
m = meters
in/PI = pipe circumference
in inches
mm/PI = pipe circumference
in millimeters
ft/PI= pipe circumference
in feet
m/PI = pipe circumference
in meters
Use the arrow keys to enter the known Pipe Wall Thickness (in inches or mm) and press [Enter]. If the pipe wall
thickness is not available, look up the value in a table of standard pipe size data which can be found in the Sound
Speeds and Pipe Size Data manual (914-004)
IMPORTANT: Because the units cannot be independently chosen for this parameter, the value must be entered in the
same units used for the pipe OD/Circumference.
1.6.2.1
Path and Axial Lengths
1. To enter the Path Length:
a.
b.
Use the [] arrow key to highlight the path length unit type at the right of the screen.Then use the [] and []
arrow keys to scroll to the desired unit type.
Use the [] arrow key to return to the numeric entry on the left, and enter the path length of the ultrasonic
signal. Press [Enter].
DigitalFlow™ XGS868i Programming Manual
9
Chapter 1. Programming Site Data
1.6.2.1
Note:
Path and Axial Lengths (cont.)
If a spoolpiece was ordered with the meter, the transducer signal path length (P) and the transducer signal
axial length (L) are engraved on the flowcell and/or are included in the documentation supplied with the
meter. For on-site transducer installations, refer to Appendix C, Measuring P and L Dimensions, in the Startup
Guide.
2.
In the same manner, enter the appropriate Axial Length L unit type and axial length of the ultrasonic signal, and
press [Enter].
3.
Scroll to the desired Fluid Type and press [Enter]. Then do one of the following:
4.
5.
• If OTHER was selected - proceed to Step 10.
• If STEAM was selected - proceed to Step 11.
Use the arrow keys to enter the Fluid Soundspeed (in feet per second) in the gas to be measured and press
[Enter].
Scroll to the appropriate choice to indicate whether you want Reynolds Correction, and press [Enter].
• If Off is selected, go to Step 12.
• If On is selected, the program asks for the Kinematic Viscosity. Use the arrow keys to enter the desired value,
and press [Enter].
6.
Use the arrow keys to enter a value for the flow Calibration Factor and press [Enter]. The default value is 1.00, but
values between 0.50 and 2.0 may be entered. The value is typically set at the factory, based on application
details.
Procedure Options
After entering the Calibration Factor, the XGS868i returns to the Channel PROGRAM. Do one of the following:
•
To continue entering “quick startup” data, press [Escape] once and proceed to Step 1 in Entering Global System
Data on page 21.
•
To continue regular programming, refer to Appendix A, Menu Maps, to navigate to the desired menu.
•
To leave the Keypad Program, press the [Escape] key twice.
10
DigitalFlow™ XGS868i Programming Manual
Chapter 1. Programming Site Data
1.7
Entering Zero Cutoff and Setting Up Inputs
Enter the zero cutoff value and set up the temperature and pressure inputs via the I/O submenu. While programming
these parameters, refer to Figure 28 on page 71.
IMPORTANT: If an option card in Slot 1 fails to appear in this menu, it may be turned Off. See the Global-I/O-Options
section on page 25 for setup instructions.
1.7.1
Zero Cutoff Value
Near a zero flow rate, the Model XGS868i’s readings may fluctuate due to small offsets caused by thermal drift or
similar factors. To force a zero display reading when there is minimal flow, enter a zero cutoff value as described
below.
1.
2.
3.
4.
In the Keypad Program, scroll to PROG and press [Enter].
In the PROG menu, scroll to CH1 or CH2 and press [Enter].
In the Channel PROGRAM menu, scroll to I/O and press [Enter].
Enter a value from 0 to 1 ft/sec (0 to 0.30 m/sec) for the Zero Cutoff and press [Enter]. The recommended setting is
0.0200 ft/sec (0.0009 m/sec).
1.7.2
Assume Saturation
This prompt permits you to use a single input for either temperature or pressure to measure mass flow. The User
Program contains a table that correlates pressure and temperature for saturated steam. If the meter can assume
the steam is always at or near saturation, then only a temperature or pressure input is needed. The meter will
interpolate the corresponding pressure or temperature.
1.
At the Assume Saturation? prompt, scroll to No or Yes and press [Enter].
• If you selected Yes, proceed to Step 2 below.
• If you selected No, proceed to Step 3 on the next page.
1.7.3
1.
Steam Input Type
Scroll to the Steam Input Type that will be used to measure mass flow and press [Enter].
• If you selected Temperature, proceed to Temperature Input on the next page.
• If you selected Pressure, proceed to Base Temperature on the next page.
IMPORTANT: Panametrics Measurement & Control recommends using a live input for either temperature or pressure
when assuming the saturation.
DigitalFlow™ XGS868i Programming Manual
11
Chapter 1. Programming Site Data
1.7.4
Temperature Input
The Model XGS868 can use either a fixed temperature value or a live temperature input to calculate the steam
density for the mass flow rate display.
1.
Scroll to a Fixed temperature value or to set up the option card in Slot 1 that will supply the live temperature input
and press [Enter].
Note:
If Slot 1 contains an activated option card with an analog input assigned to Temperature or an RTD input,
Slot 1 appears as an option at the above prompt. If the process temperature is stable, a fixed value may be
used, but most applications require a live temperature input. If there is no active option card for
temperature, the meter assumes you are using a fixed temperature.
• If you selected Fixed, proceed to Step 4.
• If you selected Slot 1, proceed to Step 5.
2.
Enter the known Fixed Temp. (process temperature) and press [Enter]. The meter will accept values from -328 to
1,832°F (-200 to 1,000oC). Proceed to Base Temperature in step 6.
3.
Scroll to Input A or Input B and press [Enter]. The inputs were labeled during setup.
Note:
The set up of Input A is used as an example. Identical procedures would be used to set up Input B.
1.7.5
Base Temperature
1.
Use the arrow keys to enter the Base Temperature and press [Enter]. The ratio of this value to the actual
temperature is used to calculate the standard mass flow rate.
• If you selected No at Assume Saturation, proceed to Step 7 below.
• If you selected Pressure as the Steam Input Type, proceed to Step 7 below.
• If you selected Temperature as the Steam Input Type, proceed to step 10 on the next page.
1.7.6
Pressure Input
Note:
If Slot 1 contains an activated option card with an input assigned to Pressure, Slot 1 appears as an option at
the above prompt. If the process pressure is stable, a fixed value may be used, but most applications
require a live pressure input. If there is no active option card for pressure, the meter assumes you are using
a fixed pressure.
1.
Scroll to a Fixed pressure value or to set up the option card in Slot 1 that will supply the live pressure input and
press [Enter].
• If you selected Fixed, proceed to Step 8.
• If you selected Slot 1, proceed to Step 9.
2.
Enter the known Fixed process Pressure and press [Enter]. The meter will only accept values from 0 to 5,000 psia.
Proceed to Base Pressure in Step 10.
3.
Scroll to Input A or Input B and press [Enter]. The inputs were labeled during setup.
Note:
12
The set up of Input A is used as an example. Identical procedures would be used to set up Input B.
DigitalFlow™ XGS868i Programming Manual
Chapter 1. Programming Site Data
1.7.7
Base Pressure
1.7.8
Low Pressure Switch
1.
1.
Enter the Base Pressure and press [Enter]. The ratio of this value to the actual pressure is used to calculate the
standard mass flow rate.
Scroll to Yes or No to activate or deactivate the Low Pressure Switch software function and press [Enter].
• If you selected Yes, enter the Pressure Limit, the low pressure switch set point, and press [Enter]. The acceptable
range is 0 to 5,000 psia. The meter will stop taking readings if the pressure drops below this value.
• If you selected No, go to Quality Input (step 12) below.
1.7.9
Quality Input
Note:
The quality value indicates what fraction of the fluid is in the gas phase. The remaining fraction is assumed
to be liquid water. Thus, a quality value of 1.0 indicates 100% gas.
When the temperature and pressure inputs indicate that the steam is saturated, the Quality Input value is used for
the mass flow rate calculations. Unless a different value is accurately known, accept the default value at the
following prompt:
1.
At the Quality Input prompt, scroll to a fixed steam quality value or to set up the option card in Slot 1 that will
supply the live steam quality input and press [Enter].
Note:
If Slot 1 contains an activated option card with an analog input that has been programmed as Special, Slot 1
appears as an option at the above prompt. Normally, a fixed value of 1.0 (100% steam) should be used for
the steam quality value.
If there is no active option card for a special input, the meter assumes you are using a fixed quality value.
• If you selected Fixed, proceed to Step 13.
• If you selected Slot 1, proceed to Step 14.
2.
Enter the known Fixed steam Quality and press [Enter]. (The meter will accept values from 0.0000 to 1.0000.) Go to
Procedure Options below.
3.
Scroll to Input A or Input B and press [Enter]. The inputs were labeled during setup.
Note:
The set up of input A is used as an example. Identical procedures would be used to set up input B.
Procedure Options
After completing the above steps, the XGS868i returns to the Channel PROGRAM window. Do one of the following:
•
To continue programming, refer to Appendix A, Menu Maps, to navigate to the desired menu.
•
To leave the Keypad Program, press [Escape] three times.
DigitalFlow™ XGS868i Programming Manual
13
Chapter 1. Programming Site Data
1.8
Entering Setup Data
The signal limits, response times, mass flow and multiple K factors for the Model XGS868i are specified via the Setup
submenu. The following four submenus are included in this section:
•
•
•
•
Signal - set the parameters related to the transducer signal (see below).
Default Setup - reset all parameters to default values (page 16).
V averaging - specify the response of the meter to step changes (page 16).
Advanced Features - enable mass flow and enter K factors
(page 18).
While following the programming instructions, refer to Figure 29 on page 72. Record all programmed data in
Appendix B, Data Records.
1.8.1
Setting Transducer Signal Parameters
Use this option to set the limits for the incoming signal and other parameters affecting the transducer signal. For
example, the programmed signal strength low limit may be used to determine the trigger point for an alarm.
CAUTION!
The Signal default settings are suitable for most applications. Consult the factory before changing
any of these parameters.
Only after consulting the factory, complete the following steps to program the signal parameters:
1.
2.
3.
4.
5.
In the Keypad Program, scroll to PROG and press [Enter].
In the PROG menu, scroll to CH1 or CH2 and press [Enter].
In the Channel PROGRAM menu, scroll to Setup and press [Enter].
Scroll to SIGNL and press [Enter].
Use Table 4 on page 15 to choose the desired values. Use the arrow keys to enter a value (or scroll to a value for a
parameter with menu options) and press [Enter].
Procedure Options
After completing the above steps, the XGS868i returns to the Channel SET UP window. Do one of the following:
•
To continue programming, refer to Appendix A, Menu Maps, to navigate to the desired menu.
•
To leave the Keypad Program, press [Escape] three times.
14
DigitalFlow™ XGS868i Programming Manual
Chapter 1. Programming Site Data
1.8.1
Setting Transducer Signal Parameters (cont.)
Transducer
Signal
Parameters
Signal Low
Limit
Correlation
Peak Limit
Soundspeed
+- Limit
Velocity Low
Limit
Velocity High
Limit
Acceleration
Limit
Amplitude
Discriminator
Low
Amplitude
Discriminator
High
Delta T Offset
Skan T Offset
% of Peak
Table 4: Transducer Signal Settings
Range
Default
Value
Miscellaneous Information
20
The E1:LOW SIGNAL error message appears when the signal strength
falls below the programmed SIGNAL LOW LIMIT value. See Chapter 2 in
the
Service Manual for a discussion of error codes.
-20 to 100
0 to 500
100
1 to 50%
-500 to 500
ft/sec
(-150 to 150
m/sec)
-500 to 500
ft/sec
(-150 to 150
m/sec)
0 to 250ft/s
(0 to 76m/s)
20%
-75.0 ft/sec
(-23 m/sec)
75.0 ft/sec
(23 m/sec)
50 ft/s
(15 m/s)
0 to 100
14
0 to 100
34
-1000 to
1000 µsec
–500 to
500 µsec
0 µsec
58 µsec
1 to 100%
DigitalFlow™ XGS868i Programming Manual
50%
The E4: SIGNAL QUALITY error message appears when the signal
quality falls below the programmed COR. PEAK LIMIT value. See
Chapter 2 in the Service Manual for a discussion of error codes
The E2:SOUNDSPEED error message appears when the calculated fluid
sound speed differs from the fluid sound speed entered in the
ChannelxSystem menu by more than the programmed SOUNDSPEED +- LIMIT
value.
See Chapter 2 in the Service Manual for a discussion of error codes.
The E3: VELOCITY RANGE error messages appears when the calculated
fluid velocity is less than the programmed VELOCITY LOW LIMIT value.
See Chapter 2 in the Service Manual for a discussion of error codes.
The E3: VELOCITY RANGE error messages appears when the calculated
fluid velocity exceeds the programmed VELOCITY HIGH LIMIT value.
See Chapter 2 in the Service Manual for a discussion of error codes.
The E6: CYCLE SKIP error message appears when the calculated fluid
velocity changes by more than the programmed ACCELERATION LIMIT
value from one reading to the next. See Chapter 2 in the Service
Manual for a discussion of error codes.
The amplitude discriminator measures the transducer signal received
by the XGS868. The default value for this parameter is 14, and values
from 0 to 100 are acceptable. The E5: AMPLITUDE error message
appears when the
amplitude discriminator falls below the programmed AMP. DISCRIM
LOW value. See Chapter 2 in the Service Manual for a discussion of
error codes.
The amplitude discriminator measures the transducer signal received
by the Model XGS868. The default value for this parameter is 34.
Values from 0 to 100 are acceptable. The E5: AMPLITUDE error
message appears when the amplitude discriminator exceeds the
programmed AMP. DISCRIM HIGH value. See Chapter 2 in the Service
Manual for a discussion of error codes.
An offset between the upstream and downstream transit times is
specified at this prompt.
At this prompt, specify a time measurement offset that compensates
for a shift resulting from cross-correlation.
The percentage of peak used to calculate the transit times and Delta T
is specified at this prompt.
15
Chapter 1. Programming Site Data
Transducer
Signal
Parameters
M>S Switch
# Shifts
A Divisor
# Transmit
Pulses
T Window
(cycles)
R Window
(cycles)
1.8.2
Table 4: Transducer Signal Settings (cont.)
Range
0 to 250
µsec
0 to 10
0.1 to 10
1 to 16
0 to 1000
10 to 128
Default
Value
50 µsec
3
2.5
4
0
10
Miscellaneous Information
If the burst mode is set to Skan/Measure (S/M), the meter switches
from Skan to Measure Mode when Delta T is less than the M>S_Switch
value. DO NOT change this value unless advised by the factory.
The number of shifts corresponds to the actual number of transmits
per cycle (number of signals added together in one direction to
produce an
averaged signal for one interrogation of the fluid) and need only be
changed if the environment is very noisy or the acoustic signal is
weak.
The Divisor used to calculate the Measure Mode integrated threshold
level is not normally changed.
# Transmit Pulses specifies the number of pulses in a burst. For
difficult conditions (i.e. long paths, high velocity or high temperature),
settings as high as 16 may be necessary.
The XGS868 calculates the size of the transmit window based on pipe
size and fluid sound speed. However, for special diagnostic purposes,
it is
possible to reset the window size.
The XGS868 calculates the size of the receive window based on pipe
size and fluid sound speed. However, for special diagnostic purposes,
it is possible to reset the window size.
Initializing Setup Parameters - Default Setup
Use this option to initialize (reset) all of the parameters within the Setup menu to their default values. Complete the
following steps to reset all of the parameters:
1.
2.
In the Keypad Program, scroll to PROG and press [Enter].
In the PROG menu, scroll to CH1 or CH2 and press [Enter].
3.
In the Channel PROGRAM menu, scroll to Setup and press [Enter].
5.
Scroll to Yes to initialize default parameters or No to abort this command. Press [Enter].
4.
Scroll to INIT. Press [Enter].
Procedure Options
After completing the above steps, the XGS868i returns to the Channel Set up window. Do one of the following:
•
To continue programming, refer to Appendix A, Menu Maps, to navigate to the desired menu.
•
To leave the Keypad Program, press [Escape] four times.
16
DigitalFlow™ XGS868i Programming Manual
Chapter 1. Programming Site Data
1.8.3
Setting Response Time - V Averaging
Use this option to specify the number of readings that occur before the meter will respond to a step change in flow
rate. In general, the smaller the number of readings, the less steady the display will appear. Complete the following
steps to set the response time:
IMPORTANT: Do not change this number unless instructed to do so by Panametrics Measurement & Control
personnel.
1.
2.
3.
4.
5.
In the Keypad Program, scroll to PROG and press [Enter].
In the PROG menu, scroll to CH1 or CH2 and press [Enter].
In the Channel PROGRAM menu, scroll to Setup and press [Enter].
Scroll to AVRG and press [Enter].
Scroll to the Response Time (in number of readings) and press [Enter]. For best results, select a value of 30 to
ensure the most stable signal.
Procedure Options
After completing the above steps, the XGS868i returns to the Channel SET UP window. Do one of the following:
•
To continue programming, refer to Appendix A, Menu Maps, to navigate to the desired menu.
•
To leave the Keypad Program, press [Escape] four times.
DigitalFlow™ XGS868i Programming Manual
17
Chapter 1. Programming Site Data
1.8.4
Using Advanced Features
This option enables you to access the more advanced features of the meter. In this option you can do the following:
•
enter a table of K factors - to compensate for non-linear flow rates (see below).
•
enable mass flow - calculated for static fluid density (see the next page).
1.8.4.1
Entering K Factors
Use this option to enter a table of K factors. K factors are used to create a curve for the flow range (based on velocity)
that compensates for non-linear flow rates. The meter accepts from 2 to 20 data pairs. Complete the following steps
to enter multiple K factors for velocity values:
Note:
1.
2.
3.
4.
5.
6.
In the Keypad Program, scroll to PROG and press [Enter].
In the PROG menu, scroll to CH1 or CH2 and press [Enter].
In the Channel PROGRAM menu, scroll to Setup and press [Enter].
Scroll to ADVAN. Press [Enter].
Scroll to MULTK, and press [Enter].
Scroll to ON to activate, or to OFF to deactivate multiple K factors, and press [Enter].
Note:
7.
The K factors are supplied by the factory; without them the K factor table cannot be edited.
If you selected OFF, go to Procedure Options on the next page.
Scroll to the Custom Type of K factor desired: CstV (velocity) or CstR (Reynolds). Press [Enter].
• If you selected CstR, the meter asks for the Kinematic Viscosity. Use the arrow keys to enter the desired value,
and press [Enter].
8.
Scroll to Yes to Edit Table, or to No to retain the current values, and press [Enter].
Note:
If you scroll to No, go to Procedure Options on the next page.
1.8.4.2
Editing K Factors
1. Use the arrow keys to enter the number of K factors (2 to 20) in the table and press [Enter].
2.
Enter the velocity (or Reynolds) value for K factor number “X” and press [Enter].
Note:
3.
4.
18
When editing the K factor table, the velocities must be entered in increasing order.
Enter the K factor corresponding to velocity number “X” (0.333 to 3.0) and press [Enter].
Repeat Steps 2 and 3 for each pair of values.
DigitalFlow™ XGS868i Programming Manual
Chapter 1. Programming Site Data
1.8.4.3
Activating Mass Flow
Use this option to calculate mass flow from a static fluid density. Complete the following steps to enter the static
density of the fluid:
IMPORTANT: The Model XGS868i calculates the actual density from the live or fixed temperature and pressure inputs,
as programmed in the I/O menu. However, setting the Mass flow calculation prompt to Yes overrides
this value and uses the density entered at the following prompt to calculate mass flow.
1.
2.
3.
4.
5.
6.
In the Keypad Program, scroll to PROG and press [Enter].
In the PROG menu, scroll to CH1 or CH2 and press [Enter].
In the Channel PROGRAM menu, scroll to Setup and press [Enter].
Scroll to ADVAN. Press [Enter].
Scroll to MASS, and press [Enter].
Scroll to Yes to activate, or to No to deactivate Static Density, and press [Enter].
Note:
7.
If you scroll to No, go to Procedure Options below.
Enter the Fluid Density and press [Enter].
Procedure Options
After completing the steps on the previous page, the XGS868i returns to the Advanced Features window. Do one of the
following:
•
To continue programming, refer to Appendix A, Menu Maps, to navigate to the desired menu.
•
To leave the Keypad Program, press [Escape] five times.
DigitalFlow™ XGS868i Programming Manual
19
Chapter 1. Programming Site Data
1.9
Entering Global Data
The Global menu is used to enter information that is not specific to either of the individual channels. Information
programmed via this menu is used to compute parameters such as the sum, difference or average of the channel 1
and channel 2 signals (for a 2-Channel meter). In addition, several general system parameters may be entered in
the Global menu.
IMPORTANT: When calculating the sum, difference or average readouts, data from the Global-System submenu is
used. Any conflicting data entered in the Channelx-System submenu is overridden.
The following submenus are included in the Global menu:
•
•
•
SYSTM - use to specify the units of measure used in calculations (see the next page).
I/O - used to set up error handling and to configure analog inputs and outputs (see page 23).
COMM- used to set up the serial communications port (see page 34).
Based on the selection made above, proceed to the appropriate section of this chapter for instructions. While
following the programming instructions, refer to Figure 30 on page 73. Remember to record all programmed data in
Appendix B, Data Records.
20
DigitalFlow™ XGS868i Programming Manual
Chapter 1. Programming Site Data
1.9.1
Entering Global System Data
This menu enables you to select the system units that the XGS868i will use when channel data is added, subtracted
or averaged together.
1.
2.
3.
In the Keypad Program, scroll to PROG and press [Enter].
In the PROG menu, scroll to GLOBL and press [Enter].
In the Global PROGRAM menu, scroll to SYSTM and press [Enter].
4.
At the System Units prompt, scroll to Eng to display measurements in English units or to Metrc for metric units and
press [Enter].
5.
Scroll to the desired Pressure Units (absolute or gauge) and press [Enter].
6.
Do one of the following:
• If absolute was selected, proceed immediately to Step 7.
• If gauge was selected, enter the desired Atmospheric Pressure, press [Enter] and proceed to the next step.
7.
Do one of the following:
• 1-Channel meter, go to Procedure Options on page 22.
• 2-Channel meter, proceed to Selecting Volumetric Units below.
1.9.1.1
Selecting Volumetric Units
1. Scroll to the desired Volumetric Units for the flow rate display and press [Enter]. Available units are listed in Table 5.
Table 5: Available Volumetric/Totalizer Units
English
Metric
2.
3.
ACF = Actual Cubic Feet
ACM = Actual Cubic Meters
KACF = Thousands of ACF
KACM = Thousands of ACM
MMACF = Millions of ACF
MMACM = Millions of ACM
SCF = Standard Cubic Feet
SCM = Standard Cubic Meters
KSCF = Thousands of SCF
KSCM = Thousands of SCM
MMSCF = Millions of SCF
MMSCM = Millions of SCM
Scroll to the desired Time units for the flow rate display and press [Enter].
Scroll to the desired number of Vol Decimal Digits (digits to the right of the decimal point in the volumetric flow
rate display) and press [Enter].
DigitalFlow™ XGS868i Programming Manual
21
Chapter 1. Programming Site Data
1.9.1.2
Selecting Totalizer Units
1. Scroll to the desired Totalizer Units for the totalized flow rate display and press [Enter]. Available units are listed in
Table 5 on page 21.
2.
3.
Scroll to the desired number of Tot Decimal Digits (digits to the right of the decimal point in the totalized flow rate
display) and press [Enter].
Do one of the following:
• If MASS FLOW is ON, proceed to Selecting the Mass Flow Units below.
• If MASS FLOW is OFF, the meter returns to the Channel PROGRAM window. Go to Procedure Options on the
following page.
Note:
To activate mass flow, refer to page 19. The following prompts will only appear if mass flow is activated for
both channels.
1.9.1.3
Selecting Mass Flow Units
1. Scroll to the desired Mass Flow units for the flow rate display and press [Enter]. The available units for this prompt
are determined by the selection made at System Units (see Table 6).
Table 6: Available Mass Flow Units
English
Metric
LB = Pounds
KG = Kilograms
KLB = Thousands of LB
Tonne = Metric Tons (1,000 KG)
MMLB = Millions of LB
Tons (2,000 LB)
2.
Scroll to the desired Mass Flow Time units for the mass flow rate display and press [Enter].
3.
Scroll to the desired number of Mdot Decimal Digits (digits to the right of the decimal point in the mass flow rate
display) and press [Enter].
4.
Scroll to the desired Mass (Totalizer) units for the totalized mass flow rate display and press [Enter]. The available
units for this prompt are determined by the selection made at the System Units prompt.
5.
Scroll to the desired number of Mass Decimal Digits (digits to the right of the decimal point in the totalized mass
flow rate display) and press [Enter].
Procedure Options
After completing the steps on the previous page, the XGS868i returns to the Global PROGRAM window. Do one of the
following:
•
To continue programming, refer to Appendix A, Menu Maps, to navigate to the desired menu.
•
To leave the Keypad Program, press [Escape] twice.
22
DigitalFlow™ XGS868i Programming Manual
Chapter 1. Programming Site Data
1.9.2
Setting Up Inputs and Outputs
Set up the XGS868i’s inputs and outputs via the I/O submenu. While following the programming instructions, refer to
Figure 30 on page 73 and Figure 31 on page 74 in Appendix A. The following three submenus are included in this
section:
•
•
•
ERROR - program the meter’s response during an error condition (see below)
OPTN - set up any option cards and the Slot 0 analog outputs (page 25)
LCD - set up the LCD display. Refer to Chapter 2, Displaying Data.
Note:
In this section, Slot 1 appears as an option only if a suitable option card is installed in Slot 1.
Proceed to the appropriate section to program the option selection made at the above prompt. Remember to record
all programmed data in Appendix B, Data Records.
1.9.2.1
Selecting Error Handling
This menu option permits programming of the manner in which the Model XGS868i’s outputs respond during an error
condition. See Chapter 2, Error Codes, in the Service Manual for a discussion of the built-in error codes. To access this
submenu:
Note:
1.
2.
3.
4.
5.
The 2-Channel meters have an additional option for error handling.
In the Keypad Program, scroll to PROG and press [Enter].
In the PROG menu, scroll to GLOBL and press [Enter].
In the Global PROGRAM menu, scroll to I/O and press [Enter].
Scroll to ERROR and press [Enter].
Scroll to the desired option for error handling and press [Enter]. If you select Error Level in mA, proceed to Step 6 on
the next page. (See Table 1-7 on the next page for a description of error handling options available and how the
totalizers and analog outputs respond to them.)
DigitalFlow™ XGS868i Programming Manual
23
Chapter 1. Programming Site Data
1.9.2.1
Note:
Selecting Error Handling (cont.)
The error responses listed in Table 7 apply only to the Channelx measurement mode and to the
Sum/Difference measurement modes, if either or both channels are in error. Error handling in the Average
measurement mode is set in Step 7 below.
Table 7: Error Response Options
Output Response
Option
6.
Totalizer Response
HOLD
Holds the last “good” reading.
Continues to totalize, based on last “good” flow
reading.
LOW
Forces outputs to the low set point.
Stops totalizing.
HIGH
Forces outputs to the high set point.
Stops totalizing.
HHIGH
Forces outputs 10% above the high set point.
Stops totalizing.
OTHER
Forces outputs to the entered mA level.
Stops totalizing during critical errors.
Use the arrow keys to enter a specific current that will signify meter errors and press [Enter]. Then, do one of the
following:
• For a 1-Channel meter, go to Procedure Options on the next page.
• For a 2-Channel meter - proceed to Step 7 below.
7.
Scroll to Yes or No to enable or disable 2-path error handling. Specific responses of the display and the totalizer
are listed in Table 8 below. The 2-path error handling option is intended for applications where two sets of
transducers are installed in the same location in the same pipe to improve accuracy and the meter is operated
in AVE mode. With this function enabled, the Model XGS868i performs error handling only if both channels are in
error. If this function is disabled, error handling occurs when either channel goes into error.
Table 8: 2-Path Error Response Options
Display Response
Option
No
Yes
Totalizer Response
Displays the average of Channel 1 and Channel 2,
regardless of the error state of either channel.
Outputs the average of Channel 1 and
Channel 2 totals, regardless of error state of
either channel.
1.
1.
If one channel is in error, the other channel’s value is
displayed as the average.
2. If both channels are in error, the last average reading
is held.
If one channel is in error, totalizing
continues.
2. If both channels are in error, totalizing
stops.
Procedure Options
After completing the above steps, the XGS868i returns to the Global I/O window. Do one of the following:
•
To continue programming, refer to Appendix A, Menu Maps, to navigate to the desired menu.
•
To leave the Keypad Program, press [Escape] four times.
24
DigitalFlow™ XGS868i Programming Manual
Chapter 1. Programming Site Data
1.9.2.2
Setting Up Slot 0 and Slot 1 Input/Outputs
The Model XGS868i has two built-in analog outputs, which are assigned to Slot 0. Also, a variety of input/output
option cards may be installed in Slot 1. See Chapter 1, Installation, of the Startup Guide for a complete description of
the available option cards.
To set up option cards, refer to one of the following sections:
•
Analog Outputs - refer to section below.
•
Analog Inputs - see page 28
•
RTD Inputs - see page 29
•
Alarm Relays - see page 30
•
Totalizer Outputs - see page 32
•
Frequency Outputs - see page 33
1.9.2.3
Analog Outputs
While following the programming instructions, refer to Figure 31 on page 74.
Accessing the Output
1.
2.
3.
4.
5.
6.
In the Keypad Program, scroll to PROG and press [Enter].
In the PROG menu, scroll to GLOBL and press [Enter].
In the Global PROGRAM menu, scroll to I/O and press [Enter].
Scroll to OPTN and press [Enter].
Scroll to Slot 0 or Slot 1, depending on which output you want to set up.
Scroll to the desired Output and press [Enter].
Note:
Output letters (A, B, etc.) correspond to the output wiring terminal numbers from top to bottom. For example,
Output A corresponds to pins 1,2 and 3; Output B corresponds to pins 4, 5 and 6; etc.
DigitalFlow™ XGS868i Programming Manual
25
Chapter 1. Programming Site Data
Setting Up the Output Scale
1.
Scroll to the desired output scale and press [Enter].
2.
Do one of the following:
• If you selected Off, the XGS868i returns to the I/O window. Go to Procedure Options on page 27.
• If you selected 0-20 mA or 4-20 mA, and are using a
• 1-Channel meter, proceed to Step 4 below.
• 2-Channel meter, proceed to the next step.
3.
Scroll to the desired Channel option (CH1, CH2, SUM, DIF or AVE) and press [Enter].
4.
Scroll to the desired Measurement Parameter and press [Enter]. See Table 9 below for a description of the
available options.
5.
At Zero, enter a flow rate value for the low end of the analog output range and press [Enter].
6.
At Full, enter a flow rate value for the high end of the analog output range and press [Enter].
Option Bar
VEL
Table 9: Available Measurement Parameters
Description
Good
Bad
Displays the flow velocity.
N.A.
N.A.
Displays the volumetric flow.
N.A.
N.A.
+TOTL
Displays the forward totalized volume flow.
N.A.
N.A.
-TOTL
Displays the reverse totalized volume flow.
N.A.
N.A.
VOLUM
TIME
Displays the total flow measurement time.
N.A.
N.A.
MDOT
Displays the mass flow.
N.A.
N.A.
+MASS
Displays the forward totalized mass flow.
N.A.
N.A.
-MASS
Displays the reverse totalized mass flow.
N.A.
N.A.
SS up
Displays the signal strength for the upstream transducer.
50–75
<50 or >75
SS do
Displays the signal strength for the downstream transducer.
50–75
<50 or >75
SNDSP
Displays the measured speed of sound in the gas.
N.A.
N.A.
Tup
Displays the upstream ultrasonic signal transit time.
N.A.
N.A.
Displays downstream ultrasonic signal transit time.
N.A.
N.A.
N.A.
N.A.
N.A.
N.A.
0.3 - 3.0
N.A.
Tdown
DELTA
REYN#
Displays the transit time difference between the upstream and
downstream signals.
Displays the Reynolds number.
Displays the K-Factor interpolated from the table, for the current velocity.
Tot K
26
1
PEAK%
Displays percentage of peak (set to +50 by default).
N.A.
N.A.
Qup
Displays signal quality for the upstream transducer.
>|800|
<|800|
Qdown
Displays signal quality for downstream transducer.
>|800|
<|800|
AMPup
Displays the value for signal amplitude of the upstream transducer.
24 ± 5
<19 or >29
AMPdn
Displays the value for signal amplitude of the downstream transducer.
24 ± 5
<19 or >29
CNTup
Displays AGC DAC count for upstream gain setting.
N.A.
N.A.
CNTdn
Displays the AGC DAC count for the downstream gain setting.
N.A.
N.A.
P#up
Displays signal peaks for the upstream transducer.
100-2300
<100 or >2300
P#dn
Displays signal peaks for downstream transducer.
100-2300
<100 or >2300
TEMP
Displays the gas temperature (from 0/4-20 mA input).
N.A.
N.A.
DigitalFlow™ XGS868i Programming Manual
Chapter 1. Programming Site Data
Table 9: Available Measurement Parameters
Description
Option Bar
Good
Bad
Displays the gas pressure (from 0/4-20 mA input).
N.A.
N.A.
AcVOL
Displays actual volumetric flow.
N.A.
N.A.
StVOL
Displays standard volumetric flow.
N.A.
N.A.
z
Displays the compressibility factor.
0–1
<0 or >1
Tu S2
Displays Skan transit time upstream.
N.A.
N.A.
Td S2
Displays Skan transit time downstream.
N.A.
N.A.
DT S2
Displays Skan Delta T.
N.A.
N.A.
Tu M2
Displays Measure transit time upstream.
N.A.
N.A.
Td M2
Displays Measure transit time downstream.
N.A.
N.A.
DT M2
Displays Measure Delta T.
N.A.
N.A.
Vinst
Displays the instantaneous velocity.
N.A.
N.A.
PRESR
Displays the saturation temperature for steam at the current pressure.
TSat
N.A.
N.A.
Displays actual temperature minus the saturation temperature (Tactual
– Tsat).
0
<0
Rho
Displays fluid density.
N.A.
N.A.
Kelvn
Displays the current process temperature in °K.
N.A.
N.A.
kPa
Displays the current process pressure in kPa
N.A.
N.A.
0.0 – 1.0
<0.0 or >1.0
TSupr
Qual
Displays the steam quality from a live input or a static programmed
value.
1 available only if Multi K-factors = ON
Note:
2 available only if Burst Mode = S/M
The measurement units that appear in these prompts are those selected in the Global-System window
earlier in this section.
Procedure Options
After completing the above steps, the XGS868i returns to the I/O window. Do one of the following:
•
To continue programming, refer to Appendix A, Menu Maps, to navigate to the desired menu.
•
To leave the Keypad Program, press [Escape] three times.
DigitalFlow™ XGS868i Programming Manual
27
Chapter 1. Programming Site Data
1.9.2.4
Analog Inputs
Refer to Figure 31 on page 74, and complete the following steps to set up the analog inputs of an option card installed
in Slot 1:
Accessing the Input
1.
2.
3.
4.
5.
6.
In the Keypad Program, scroll to PROG and press [Enter].
In the PROG menu, scroll to GLOBL and press [Enter].
In the Global PROGRAM menu, scroll to I/O and press [Enter].
Scroll to OPTN and press [Enter].
Scroll to Slot 1 and press [Enter].
Scroll to the desired Input and press [Enter].
Note:
Input letters (A, B, etc.) correspond to input wiring terminal numbers from top to bottom (e.g. Input A
corresponds to pins 1,2 and 3; Input B corresponds to pins 4, 5 and 6; etc.).
Setting Up the Input
1.
2.
Enter a Label of up to eight characters for input and press [Enter].
Scroll to the desired input Measurement and press [Enter]. Do one of the following:
• If Off was selected, go to Procedure Options below.
• If Pressure or Temperature was selected, proceed to Step 5.
3.
4.
• If Special was selected to set up the input as a live special input, proceed to the next step.
Use the arrow keys to enter a Name for the input and press [Enter].
Use the arrow keys to enter a Unit of measurement for the input and press [Enter].
5.
Use the arrow keys to enter a value (a temperature value for special inputs) for the low end of the analog input
range and press [Enter].
6.
Use the arrow keys to enter a value (a temperature value for special inputs) for the high end of the analog input
range and press [Enter].
Procedure Options
After completing the above steps, the XGS868i returns to the I/O window. Do one of the following:
•
To continue programming, refer to Appendix A, Menu Maps, to navigate to the desired menu.
•
To leave the Keypad Program, press [Escape] four times.
28
DigitalFlow™ XGS868i Programming Manual
Chapter 1. Programming Site Data
1.9.2.5
RTD Inputs
Option cards with RTD inputs have a temperature range of –148 to 662°F (–100 to 350°C). While following the
programming instructions, refer to Figure 31 on page 74, and complete the following steps to set up the RTD inputs of
an option card installed in Slot 1.
Accessing the Input
1.
In the Keypad Program, scroll to PROG and press [Enter].
3.
In the Global PROGRAM menu, scroll to I/O and press [Enter].
2.
4.
5.
6.
In the PROG menu, scroll to GLOBL and press [Enter].
Scroll to OPTN and press [Enter].
Scroll to Slot 1 and press [Enter].
Scroll to the desired Input and press [Enter].
Note:
Input letters (A, B, etc.) correspond to input wiring terminal numbers from top to bottom (e.g. Input A
corresponds to pins 1,2 and 3; Input B corresponds to pins 4, 5 and 6; etc.).
Setting Up the RTD Input
1.
2.
3.
4.
Enter a Label for the RTD input and press [Enter].
Scroll to the desired input type and press [Enter]. Do one of the following:
• If Off was selected, go to Procedure Options below.
• If Temperature was selected, proceed to the next step.
Enter a temperature value for the Low end of the analog input range and press [Enter].
Enter a temperature value for the High end of the analog input range and press [Enter].
Procedure Options
After completing the above steps, the XGS868i returns to the I/O window. Do one of the following:
•
To continue programming, refer to Appendix A, Menu Maps, to navigate to the desired menu.
•
To leave the Keypad Program, press [Escape] four times.
DigitalFlow™ XGS868i Programming Manual
29
Chapter 1. Programming Site Data
1.9.2.6
Alarm Relays
Refer to Figure 31 on page 74, and complete the following steps to set up the alarm relays of an option card installed
in Slot 1:
Accessing the Alarm Relay
1.
2.
3.
4.
5.
6.
In the Keypad Program, scroll to PROG and press [Enter].
In the PROG menu, scroll to GLOBL and press [Enter].
In the Global PROGRAM menu, scroll to I/O and press [Enter].
Scroll to OPTN and press [Enter].
Scroll to Slot 1 and press [Enter].
Scroll to the desired Output and press [Enter].
Note:
Output letters (A, B, etc.) correspond to the output wiring terminal numbers from top to bottom (e.g. Output
A corresponds to pins 1,2 and 3; Output B corresponds to pins 4, 5 and 6; etc.).
Selecting the Alarm Type
1.
2.
Scroll to the desired Alarm type and press [Enter].
Do one of the following:
• If you selected Off, the XGS868i returns to the I/O window. Go to Procedure Options on the next page.
• If you selected High, Low or Fault, proceed to the next step.
3.
Scroll to the appropriate mode (Standard or Failsafe), and press [Enter]. (See Chapter 1, Installation, of the Startup
Guide for wiring instructions.)
4.
Do one of the following:
• If you are using a 1-Channel meter and selected
• high or low - proceed to Step 7 on the next page.
• fault - proceed to Step 9 on the next page.
• If you are using a 2-Channel meter, proceed to the next step.
5.
30
Scroll to the desired Channel option and press [Enter].
DigitalFlow™ XGS868i Programming Manual
Chapter 1. Programming Site Data
1.9.2.6
Alarm Relays (cont.)
Selecting the Alarm Type (cont.)
6.
Do one of the following:
• high or low - proceed to Step 7 below.
• fault - proceed to Step 9 below.
7.
Scroll to the desired measurement parameter and press [Enter]. (See Table 9 on page 26 for a description of the
available options.)
Note:
8.
9.
The measurement units that appear in these prompts are those selected in the Global-System window
earlier in this section.
Enter a value for the Trigger Point of the alarm and press [Enter]. Go to Procedure Options below.
Scroll to the type of Error (flow, non-flow or both) that will trigger the fault alarm and press [Enter].
Procedure Options
After completing the previous steps, the XGS868i returns to the I/O window. Do one of the following:
•
To continue programming, refer to Appendix A, Menu Maps, to navigate to the desired menu.
•
To leave the Keypad Program, press [Escape] three times.
DigitalFlow™ XGS868i Programming Manual
31
Chapter 1. Programming Site Data
1.9.2.7
Totalizer Outputs
The totalizer output issues one pulse per selected volume of flow. The meter produces a pulse each time the
programmed amount of flow passes through the pipe. Refer to Figure 31 on page 74, and complete the following
steps to set up the totalizer outputs of an option card installed in Slot 1:
Accessing the Totalizer Output
1.
In the Keypad Program, scroll to PROG and press [Enter].
3.
In the Global PROGRAM menu, scroll to I/O and press [Enter].
2.
4.
5.
6.
7.
In the PROG menu, scroll to GLOBL and press [Enter].
Scroll to OPTN and press [Enter].
Scroll to Slot 1 and press [Enter].
Scroll to the desired Output and press [Enter].
Do one of the following:
• If you selected Off, the XGS868i returns to the I/O window.
Go to Procedure Options on the following page.
• If you selected TTLZR, and are using a
• 1-Channel meter, proceed to Step 2 on the next page.
Note:
• 2-Channel meter, proceed to Step 1 on the next page.
Output letters (A, B, etc.) correspond to the output wiring terminal numbers from top to bottom (e.g. Output
A corresponds to pins 1,2 and 3; Output B corresponds to pins 4, 5 and 6; etc.).
Setting Up the Totalizer
1.
2.
Scroll to the desired Channel option and press [Enter].
Scroll to the desired Measurement parameter and press [Enter]. See Table 10 below for a list of the available
options.
Table 10: Output Measurement Options
Forward Totalized Volume Flow
Reverse Totalized Volume Flow
Forward Totalized Mass Flow
Reverse Totalized Mass Flow
Note:
3.
Use the arrow keys to enter a value for the minimum Pulse On time (between 1 sec and 10,000 sec) for the
frequency of the totalizer pulses and press [Enter].
Note:
4.
The measurement units that appear in these prompts are those selected in the Global-System window
earlier in this section.
A complete pulse consists of equal amounts of ON and OFF times. Choose a value that is compatible with
the frequency counter to be used.
Use the arrow keys to enter a value for the number of measurement units represented by each pulse and press
[Enter].
Procedure Options
After completing the above steps, the XGS868i returns to the I/O window. Do one of the following:
•
To continue programming, refer to Appendix A, Menu Maps, to navigate to the desired menu.
•
To leave the Keypad Program, press [Escape] four times.
32
DigitalFlow™ XGS868i Programming Manual
Chapter 1. Programming Site Data
1.9.2.8
Frequency Outputs
The frequency output issues a continuous signal with a frequency proportional to the selected measurement. Refer
tFigure 31 on page 74 and complete the following steps to set up the totalizer outputs of an option card installed in
SLOT 1:
Accessing the Frequency Output
1.
In the Keypad Program, scroll to PROG and press [Enter].
3.
In the Global PROGRAM menu, scroll to I/O and press [Enter].
2.
4.
5.
6.
7.
In the PROG menu, scroll to GLOBL and press [Enter].
Scroll to OPTN and press [Enter].
Scroll to Slot 1 and press [Enter].
Scroll to the desired Output and press [Enter].
Do one of the following:
• If you selected Off, the XGS868i returns to the Input/Output window. Go to Procedure Options on the following
page.
• If you selected Frequency, and are using a
• 1-Channel meter, proceed to Step 2 on the next page.
Note:
• 2-Channel meter, proceed to Step 1 on the next page.
Output letters (A, B, etc.) correspond to the output wiring terminal numbers from top to bottom (e.g. Output
A corresponds to pins 1,2 and 3; Output B corresponds to pins 4, 5 and 6; etc.).
Setting Up the Frequency
1.
2.
Scroll to the desired Channel option and press [Enter].
Scroll to the desired Measurement parameter and press [Enter]. See Table 9 on page 26 for a description of the
available options. Refer to page 3-2 in the Service Manual for a description of diagnostic parameters.
Note:
3.
Use the arrow keys to enter a value for the Low end of the frequency output range and press [Enter].
Note:
4.
5.
The measurement units that appear in these prompts are those selected in the Global-System window
earlier in this section.
A complete pulse consists of equal amounts of ON and OFF times. Choose a value that is compatible with
the frequency counter to be used.
Use the arrow keys to enter a value for the High end of the frequency output range and press [Enter].
Use the arrow keys to enter a value between 1 and 10,000 for the Frequency at full scale and press [Enter].
Procedure Options
After completing the above steps, the XGS868i returns to the I/O window. Do one of the following:
•
To continue programming, refer to Appendix A, Menu Maps, to navigate to the desired menu.
•
To leave the Keypad Program, press [Escape] four times.
DigitalFlow™ XGS868i Programming Manual
33
Chapter 1. Programming Site Data
1.9.3
Configuring the Communications Port
The Model XGS868i flowmeter is equipped with an RS232 or an RS485 serial interface. An RS485 option is also
available with MODBUS capability. When the MODBUS option is installed, the XGS868i may still also have the standard
RS232 serial interface.
The meter can be configured with a MODBUS option card for MODBUS communications, a Foundation Fieldbus option
card for Foundation Fieldbus communications, an Ethernet option card for Ethernet communications, or with a
MODBUS/TCP option card for MODBUS communication over the Ethernet, if desired.
Note:
To set Fieldbus communications parameters, see Appendix E, Foundation Fieldbus Communications.
The serial port is used to transmit stored data and displayed readings to a personal computer by connecting the
meter’s serial interface to the serial port of the PC. Also, the Model XGS868i can receive and execute remote
commands, using PanaView software with this link.
Use the COMM submenu to set the communications port and MODBUS parameters. While programming the meter,
refer to Figure 31 on page 74.
1.9.3.1
Setting Up the Serial Port
Use the steps below to configure the communications port:
1.
2.
3.
4.
In the Keypad Program, scroll to PROG and press [Enter].
In the PROG menu, scroll to GLOBL and press [Enter].
In the Global PROGRAM menu, scroll to COMM and press [Enter].
Enter a Meter Address (between 1 and 127) and press [Enter]. (The default address is 1.)
A meter address is necessary for communication with the Panametrics Measurement & Control PanaView software.
See Appendix C, Programming the XGS868i with PanaView™, or the PanaView™ User’s Manual (910-211) for more
information.
IMPORTANT: If the meter address or baud rate is changed, communication with PanaView must be re-established
with the new parameters.
5.
6.
Scroll to the desired Baud Rate and press [Enter]. (Available baud rates extend from 300 to 19,200.)
Do one of the following:
• If you have the RS485 MODBUS option, proceed to Step 1 in Setting Up MODBUS Communications on the
following page.
• If you have the standard RS232 serial interface, go to Procedure Options on the next page.
34
DigitalFlow™ XGS868i Programming Manual
Chapter 1. Programming Site Data
1.9.3.2
Setting Up MODBUS Communications
When equipped with an optional MODBUS output card, the XGS868i can transmit flow data serially to a flow
computer, or SCADA, using a Gould-type RTU protocol. Thus only the MODBUS function command, 3 (read multiple
registers), 6 (write multiple registers) is valid. The XGS868i uses the following format for the data exchange:
•
The Send command (initiated by the host flow computer or controller) comes in the form:
[time delimiter]<Addr><3><First Register MSB>
<First Register LSB> <Register Count MSB>
<Register Count LSB><CRC Low><CRC High>[time delimiter]
•
The Response (initiated by the host flow computer or controller) comes in the form:
[time delimiter]<Addr><3><Byte count><Data...........>
<CRC Low><CRC High>[time delimiter]
The format for the returned data types is:
•
Integer (16 bit Integer) <MSB><LSB>
1 Register - 16 bit integer
•
Integer (32 bit IntegerI) <MSB><LSB><LSB><LSB>
2 Register - 32 bit integer
•
Floating Point (FP)<EXP><MAN><MAN><MAN>
2 Registers - 32 bit IEEE floating point number
Use the steps below to configure MODBUS communications:
IMPORTANT: The XGS868i MODBUS communications settings chosen in the next four steps must match those of the
MODBUS control system.
1.
2.
3.
4.
Scroll to the desired MODBUS Baud Rate and press [Enter].
Scroll to the MODBUS Parity and press [Enter].
Scroll to the MODBUS Stop Bits and press [Enter].
Enter a MODBUS Meter Address (between 1 and 254) and press [Enter]. (The default address is 1.)
IMPORTANT: You must reboot the XGS868i to load the new settings.
Procedure Options
After completing the above steps, the XGS868i returns to the Global PROGRAM window. Do one of the following:
•
Refer to the section Requesting Parameters Using MODBUS on the following page to retrieve data from the
XGS868i using MODBUS.
•
To continue regular programming, refer to Appendix A, Menu Maps, to navigate to the desired menu.
•
To leave the Keypad Program, press [Escape] three times.
DigitalFlow™ XGS868i Programming Manual
35
Chapter 1. Programming Site Data
1.9.4
Requesting Parameters Using MODBUS
Note:
If you request Channel2 or Averaged data from a 1-Channel meter, the values will all be zero.
To request specific parameters from the XGS868i via the MODBUS, the control system must enter the appropriate
register number. Only registers 1 through 90 are available for MODBUS communications, while registers 508 through
512 are used by the XGS868i to store the MODBUS parameters. For details, see Table 11 below for a 1-Channel meter or
Table 12 on page 36 for a 2-Channel meter.
DPR
Hex Addr
1
0
1”Clear Ch1 Totalizers”
--
2 (16 bit signed)
2
2
Not Used
--
2 (16 bit signed)
Size in Bytes
3
4
Velocity
2
4 (2 16-bit int)
5
8
Act Volumetric
#Q DIGITS
4 (IEEE 32 bit)
7
C
Std Volumetric
#Q DIGITS
4 (IEEE 32 bit)
9
10
Fwd Totals
#T DIGITS
4 (2 16 bit int)
11
14
Rev Totals
#T DIGITS
4 (2 16 bit int)
13
18
#Tot Digits
0
2
14
1A
Mass Flow
#M DIGITS
4 (IEEE 32 bit)
16
1E
Fwd Mass Totals
#MT DIGITS
4 (2 16-bit int)
18
22
Rev Mass Totals
#MT DIGITS
4 (2 16-bit int)
20
26
#Mass Tot Digits
0
2
21
28
Timer
2
4 (2 16-bit int)
23
2C
Error Code
0
2
24
2E
Sound Speed
3
4 (2 16-bit int)
26
32
Density
4
4 (2 16-bit int)
28
36
Signal Strength Upstream
1
4 (2 16-bit int)
30
3A
Signal Strength Downstream
1
4 (2 16-bit int)
32
3E
Temperature
2
4 (2 16-bit int)
34
42
Pressure
3
4 (2 16-bit int)
508
3F6
2
MODBUS baud rate
0
2
509
3F8
3MODBUS parity
0
2
510
3FA
4MODBUS stop bits
0
2
511
3FC
MODBUS meter addr
0
2
512
3FE
RESERVED
---
---
MODBUS
Reg #
36
Table 11: MODBUS Registers for a 1-Channel XGS868i
Scaling
(decimal places)
Description
MODBUS
Reg #
Table 12: MODBUS Registers for a 2-Channel XGS868i
DPR
Scaling
Hex Addr
(decimal places)
Description
Size in Bytes
--
2 (16 bit signed)
1
0
1”Clear Ch1 Totalizers”
2
2
1“
Clear Ch2 Totalizers”
--
2 (16 bit signed)
3
4
Ch1 Velocity
2
4 (2 16-bit int)
5
8
Ch1 Act Volumetric
#Q DIGITS
4 (IEEE 32 bit)
DigitalFlow™ XGS868i Programming Manual
Chapter 1. Programming Site Data
7
C
9
10
Table 12: MODBUS Registers for a 2-Channel XGS868i
Ch1 Std Volumetric
#Q DIGITS
4 (IEEE 32 bit)
Ch1 Fwd Totals
#T DIGITS
4 (2 16 bit int)
11
14
Ch1 Rev Totals
#T DIGITS
4 (2 16 bit int)
13
18
Ch1 #Tot Digits
0
2
14
1A
Ch1 Mass Flow
#M DIGITS
4 (IEEE 32 bit)
16
1E
Ch1 Fwd Mass Totals
#MT DIGITS
4 (2 16-bit int)
18
22
Ch1 Rev Mass Totals
#MT DIGITS
4 (2 16-bit int)
20
26
Ch1 #Mass Tot Digits
0
2
21
28
Ch1 Timer
2
4 (2 16-bit int)
23
2C
Ch1 Error Code
0
2
24
2E
Ch1 Sound Speed
3
4 (2 16-bit int)
26
32
Ch1 Density
4
4 (2 16-bit int)
28
36
Ch1 Sig Strength Upstream
1
4 (2 16-bit int)
30
3A
Ch1 Sig Strength Downstream
1
4 (2 16-bit int)
32
3E
Ch1 Temperature
2
4 (2 16-bit int)
34
42
Ch1 Pressure
3
4 (2 16-bit int)
36
46
Ch2 Velocity
2
4 (2 16-bit int)
38
4A
Ch2 Act Volumetric
#Q DIGITS
4 (IEEE 32 bit)
40
4E
Ch2 Std Volumetric
#Q DIGITS
4 (IEEE 32 bit)
42
52
Ch2 Fwd Totals
#T DIGITS
4 (2 16 bit int)
44
56
Ch2 Rev Totals
#T DIGITS
4 (2 16 bit int)
46
5A
Ch2 #Tot Digits
0
2
47
5C
Ch2 Mass Flow
#M DIGITS
4 (IEEE 32 bit)
49
60
Ch2 Fwd Mass Totals
#MT DIGITS
4 (2 16-bit int)
51
64
Ch2 Rev Mass Totals
#MT DIGITS
4 (2 16-bit int)
53
68
Ch2 #Mass Tot Digits
0
2
54
6A
Ch2 Timer
2
4 (2 16-bit int)
56
6E
Ch2 Error Code
0
2
57
70
Ch2 Sound Speed
3
4 (2 16-bit int)
59
74
Ch2 Density
4
4 (2 16-bit int)
MODBUS
Reg #
DPR
Hex Addr
Scaling
(decimal places)
Size in Bytes
61
78
Ch2 Sig Strength Upstream
1
4 (2 16-bit int)
63
7C
Ch2 Sig Strength Downstream
1
4 (2 16-bit int)
65
80
Ch2 Temperature
2
4 (2 16-bit int)
67
84
Ch2 Pressure
3
4 (2 16-bit int)
69
88
Avg Velocity
2
4 (2 16-bit int)
71
8C
Avg Act Volumetric
#Q DIGITS
4 (IEEE 32 bit)
Description
73
90
Avg Std Volumetric
#Q DIGITS
4 (IEEE 32 bit)
75
94
Avg Fwd Totals
#T DIGITS
4 (2 16 bit int)
77
98
Avg Rev Totals
#T DIGITS
4 (2 16 bit int)
79
9C
Avg #Tot Digits
0
2
DigitalFlow™ XGS868i Programming Manual
37
Chapter 1. Programming Site Data
80
9E
82
A2
Table 12: MODBUS Registers for a 2-Channel XGS868i
Avg Mass Flow
#M DIGITS
4 (IEEE 32 bit)
Avg Fwd Mass Totals
#MT DIGITS
4 (2 16-bit int)
84
A6
Avg Rev Mass Totals
#MT DIGITS
4 (2 16-bit int)
86
AA
Avg #Mass Tot Digits
0
2
87
AC
Avg Timer
2
4 (2 16-bit int)
89
B0
5
Avg Error Code
0
2
90
B2
Avg Sound Speed
3
4 (2 16-bit int)
508
3F6
2
MODBUS baud rate
0
2
509
3F8
3
MODBUS parity
0
2
510
3FA
4
MODBUS stop bits
0
2
511
3FC
MODBUS meter addr
0
2
512
3FE
RESERVED
---
---
1.9.4.1
Notes:
1. Clear Totalizers: flag from the 8051 to clear either the Channel 1 or Channel 2 totalizers.
2.
MODBUS baud rate: 5 = 2400, 6 = 4800, 7 = 9600
3.
MODBUS parity: 0 = none, 1 = odd, 2 = even
5.
AVG Error Code:
0=Both Ch1 and Ch2 are in error.
1=Ch1 only is in error
2=Ch2 only is in error
3=Both channels are error free
4.
38
MODBUS stop bits: 1 = 1 stop bit, 2 = 2 stop bits
DigitalFlow™ XGS868i Programming Manual
Chapter 1. Programming Site Data
1.9.5
Activating Security
In order to prevent unauthorized tampering with the flowmeter’s programming, the XGS868i is equipped with a
security feature that locks all the keys except [PROG] (which, when pressed, requires the password).
When the system is locked, access to the menus will be denied unless the correct password is entered. The XGS868i is
shipped with a default password (2719 and three spaces). For increased security, the default password should be
changed.
IMPORTANT: Once the system has been locked, it can only be unlocked by entering the password, because access
to the SECUR submenu is restricted.
While following the programming instructions, refer to the menu map in Figure 30 on page 73.
IMPORTANT: It is recommended that all program parameters be recorded before changing the password. (This
information should be recorded in Appendix B, Data Records, as a matter of routine.) If the password is
lost, the site data is not retrievable and will have to be re-entered.
1.
In the Keypad Program, scroll to PROG and press [Enter].
3.
Scroll to SECUR and press [Enter].
2.
4.
From the PROGRAM menu, scroll to GLOBL and press [Enter].
At the Lock Out prompt, scroll to UNlck to unlock the system and return to the initial PROGRAM menu, or scroll to
LOCK to lock the system.
Note:
5.
6.
If the system was unlocked at the above prompt, the following steps do not appear.
Enter the current or default Password and press [Enter].
At the Edit Password prompt, scroll to NO and press [Enter] to leave the password unchanged, or scroll to YES to
enter a new password.
IMPORTANT: Since the default password is printed in this manual, a new password should be entered. If the
password is ever lost, contact the factory for assistance.
7.
Enter the New Password and press [Enter]. Any combination of letters and numbers up to a total of 7 characters
may be used as a password.
8.
Verify the New Password by entering it again and press [Enter]. Be sure to record the new password in a safe
place.
1.10
Exiting the User Program
After completing the COMM option, the XGS868i returns to the Global PROGRAM prompt. Press [Escape] twice to
return to the Keypad Program, and a third time to return to the meter display. Then proceed to Chapter 3, Operation,
of the Startup Guide for instructions on taking measurements, or refer to the appropriate chapters of this manual for
detailed instructions on using the other features of the XGS868i flow transmitter.
DigitalFlow™ XGS868i Programming Manual
39
Chapter 1. Programming Site Data
[no content intended for this page]
40
DigitalFlow™ XGS868i Programming Manual
Chapter 2. Displaying Data
Chapter 2. Displaying Data
2.1
Introduction
This chapter explains how to display measurement data using either of the available methods:
•
•
LCD Display - show data on the built-in display
PanaView - display data on a computer terminal using the optional PanaView software
2.2
Displaying Data with the LCD
When equipped with the Liquid Crystal Display (LCD), the Model XGS868i may be programmed to display up to four
variables in sequence. In addition, the contrast of the LCD may be adjusted for optimum viewing. Proceed to the
appropriate section for instructions, and refer to Figure 30 on page 73 of Appendix A, Menu Maps.
2.2.1
Adjusting LCD Contrast
The LCD contrast may be adjusted through the Keypad Program to suit individual needs.
1.
Press [Escape]. [Enter], [Escape].
2.
In the Keypad Program window, scroll to CNTRS and press [Enter].
4.
When you have achieved the desired contrast, scroll to STORE to retain the setting, or to ABORT to leave the menu
without changing the setting. In either case, the XGS868i returns to the Keypad Program.
5.
Then press [Escape] to return to the display screen.
3.
Scroll to DARKN or LITEN and press [Enter] until the screen shows the desired contrast.
DigitalFlow™ XGS868i Programming Manual
41
Chapter 2. Displaying Data
2.2.2
Note:
Programming the LCD
When you first initialize the XGS868i, the number of LCD parameters is set to OFF. You must program the LCD
to display any measured parameters.
Through the Keypad Program, you can program the LCD display to display up to four variables in sequence.
Complete the following steps to program the LCD display:
1.
2.
3.
Power up the XGS868i and wait until it has initialized.
Press [Escape], [Enter], [Escape].
In the Keypad Program window, scroll to PROG and press [Enter].
4.
In the PROG menu, scroll to GLOBL and press [Enter].
6.
Scroll to LCD and press [Enter].
5.
7.
Scroll to I/O and press [Enter].
The window now asks for the # of LCD Parameters. Scroll to the desired number (from OFF through 1-4 and KEY)
and press [Enter].
The OFF setting switches the measurement display off, while the KEY setting enables users to change the
measurement display via the arrow keys, without accessing the Keypad Program. If you select KEY:
•
To view a different parameter, press the [] and [] keys to scroll through the various parameters.
•
To scroll through the channel options on a two-channel XGS868i, press the [] and [] keys until you have
reached the desired option.
For a 1-Channel XGS868i, the data for Channel 1 is displayed automatically, and you can skip to step 9. However, for a
2-Channel meter, the channel data to be displayed must be specified at the following prompt.
42
DigitalFlow™ XGS868i Programming Manual
Chapter 2. Displaying Data
2.2.2
8.
Programming the LCD (cont.)
Scroll to the desired Channel option, as listed in Table 13.
Table 13: Channel Options
Option
Description
9.
CH1
Channel 1
CH2
Channel 2
SUM
CH1+CH2
DIF
CH1-CH2
AVE
(CH1+CH2)/2
For each channel, select the desired Measurement Parameter, as shown in Table 9 on page 26.
Note:
The measurement units that appear in these prompts are those selected in the GLOBL-SYSTM menu earlier
in this manual. Also, when differences in one channel's programming invalidate an output previously chosen
for the other, the measurement defaults to the nearest selectable item in the parameter list.
The previous two prompts repeat until all of the specified # of LCD Parameters have been set up. When all of the
display parameters have been set up, the meter returns to the Global I/O window. To leave the Keypad Program,
press the [Escape] key three times.
After leaving the Keypad Program, the XGS868i will reset itself and will begin to display the parameters specified in
this section. If more than one parameter was set up, each of the parameters will be displayed in sequence, with a
pause of several seconds between display changes.
DigitalFlow™ XGS868i Programming Manual
43
Chapter 2. Displaying Data
2.3
Displaying Data on a Computer Terminal
The flow rate data collected by the XGS868i may be displayed in various formats on a remote computer terminal via
the meter’s RS232 serial port. This requires the use of the optional PanaView software. Refer to the instructions below
to display data via PanaView.
2.3.1
Preparing for PanaView Programming
Before you attempt to communicate with the XGS868i, be sure you have linked your PC to the XGS868i via an RS232
interface. For details on wiring the interface, refer to Wiring the Serial Port in the Startup Guide, and to the document
EIA-RS Serial Communications (916-054). You must also install PanaView, as discussed in the PanaView User’s
Manual (910-211), and in Appendix C, Programming the XGS868i via PanaView™.
1.
2.
3.
Power up the XGS868i and wait until it has initialized.
Launch PanaView and wait until it initializes the XGS868i and displays the basic PanaView window.
As described in Appendix C, open the Meter Browser window and highlight the meter to be used.
At this time, any of PanaView’s comprehensive data handling capabilities may be used. These include:
•
collecting and displaying live data in text format
•
collecting and displaying live data in graphical format
•
collecting and logging live data
•
displaying a log file in text format
•
displaying a log file in graphical format
To access PanaView’s data handling options, pull down the Output menu, as shown in Figure 2.
Figure 2: The Output Menu
44
DigitalFlow™ XGS868i Programming Manual
Chapter 2. Displaying Data
2.3
Displaying Data on a Computer Terminal (cont.)
Proceed directly to the appropriate section for instructions on either of the following output options:
•
Text Display output, discussed below
•
Graphing output on page 47
Note:
For information on the Logging output, see Chapter 3, Logging Data.
2.3.1
The Text Display Output
To collect data from the instrument and display it on a text screen, complete the following steps:
1.
2.
Complete Steps 1-3 on page 44.
Pull down the Output menu and click on the Text Display option (see Figure 2 on page 44).
Note:
3.
The Text Display window that appears after Step 2 is actually stacked on top of any previously opened
windows (such as the Meter Browser window).
Using the Window menu, arrange the open windows in the desired format. For this discussion, Figure 3 shows the
Text Display window in its maximized (full-screen) size.
Figure 3: The Text Display Window
Note:
4.
Figure 3 has been compressed both vertically and horizontally for improved clarity.
The left pane of the Text Display window contains the standard PanaView network tree. Expand this tree as far as
necessary, and double click on the desired process parameter to display it in the right pane of the window.
DigitalFlow™ XGS868i Programming Manual
45
Chapter 2. Displaying Data
2.3.1
5.
The Text Display Output (cont.)
Before actual data values can be displayed in the text pane, activate one of the following data collection modes
(see Figure 3 on page 45):
• Click on the [Get Once] option button at the bottom of the right pane in the Text Display window. The current
value of the selected process parameter, as specified in the PanaView network tree, is displayed in the right
pane of the Text Display window.
or
• Enter an interval in the text box at the bottom of the right pane in the Text Display window, or check the Max.
Comm Rate box to collect readings as fast as the system allows (1 sec). Then, click on the [Continuous] option
button to begin collecting data for display in the right pane of the Text Display window.
Note:
6.
Any value entered in the Interval text box is overridden if the Max. Comm Rate box is checked.
If the [Continuous] option was selected in Step 5 above, click on the [Stop] option button, which has replaced
the original [Continuous] option button, to terminate data collection.
The Text Display window may be left open while other tasks are performed, or it may be closed by clicking on the
lower [X] control button at the far right of the menu bar.
IMPORTANT: If you click on the upper [X] control button at the far right of the PanaView title bar, you will exit
PanaView completely.
2.3.1.1
Displaying Multiple Process Parameters
The procedure for displaying a single process parameter in a text screen may be repeated to simultaneously display
multiple process parameters. To do so, proceed as follows:
1.
Display the first process parameter in a text screen, as described in the previous section.
2.
Repeat Step 1 for any desired additional process parameters, by double clicking on them in the PanaView
network tree. PanaView automatically tiles the multiple text screens in the right pane of the Text Display window.
3.
As in any standard Windows application, the multiple text screens may be resized by dragging their borders. Also,
the individual panes within a parameter’s text screen may be resized by dragging the borders within that text
screen.
4.
To close an open text screen, right click anywhere within that screen (except in the title bar or the error section)
and click on the [Remove] option that pops up in the context menu.
Note:
46
After resizing or removing any of the multiple text screens, the default tiled layout may be restored by
opening the “Window” menu (see the PanaView User’s Manual) and clicking on the “Tile Output Displays”
option.
DigitalFlow™ XGS868i Programming Manual
Chapter 2. Displaying Data
2.3.1.2
Displaying Multiple Text Windows
The procedures for displaying one or more process parameters in a single Text Display window may be repeated to
open multiple Text Display windows. To do so, proceed as follows:
1.
2.
3.
To open another Text Display window, repeat the steps on page 45 and page 46.
To display the desired process parameter(s) in the new window, repeat Steps 1-4 on page 46.
Arrange the multiple Text Display windows as desired via the Window menu.
2.3.2
The Graphing Output
To collect data from the instrument and display it graphically in a new format, complete the following steps:
2.3.2.1
Setting Up a Graph
1. Perform Steps 1-3 on page 44.
2.
Pull down the Output menu and click on the Graphing - New option (see Figure 2 on page 44).
Note:
3.
The Graph window is stacked on top of any previously opened windows (such as the Meter Browser
window).
Using the Window menu, arrange the open windows in the desired format. For this discussion, Figure 4 shows the
Graph window in its maximized (full-screen) size.
Figure 4: The Graph Window
The Graph window shown above consists of three panes:
•
left pane - PanaView network tree
•
top right pane - graph with default chart style
•
bottom right pane - graph controls or text display
Note:
The three panes of the Graph window may be resized by simply dragging their borders.
DigitalFlow™ XGS868i Programming Manual
47
Chapter 2. Displaying Data
2.3.2.2
Graphing Data
The PanaView network tree has already been described, and the display pane shows only a graph in the default style
with no data points. The bottom right pane enables you to set up the graph. To begin graphing your data, proceed as
follows:
1.
Expand the network tree as far as necessary and double click on the process parameter to be graphed. The grid
for the selected graph appears in the display pane, with Time as the x-axis and the parameter Value as the
y-axis. In addition, a legend appears above the graph, which indicates the name, data point shape and line color
for that parameter.
2.
If desired, a second parameter may be added to the graph by repeating Step 1. In this case, the parameter
“Value” is shown as a right y-axis (Y2).
Note:
Although only two parameters may be graphed for any one meter channel, the same two parameters may
also be graphed for any other active meter channels.
3.
To begin plotting data for the selected parameter(s), enter a time Interval for data sampling in the text box
provided (the default value is 5 seconds).
4.
Click on the [Plot Continuous] control button to begin graphing the selected process parameter(s) as a function
of time, at the interval specified in Step 3.
5.
While PanaView is graphing the data, the following actions may be taken from the control pane:
• change the sampling interval by entering a new value
• click on the [Zoom Out] control button to increase the size of the intervals shown on the x-axis
• click on the [Zoom In] control button to decrease the size of the intervals shown on the x-axis
Note:
The zoom buttons may be clicked multiple times to enhance the effect.
• click on the Text Display tab to view the data being graphed in the text format described in the previous section
When you have finished graphing your data, click on the [Stop] control button, which has replaced the original [Plot
Continuous] control button.
For further information on setting up graph properties, refer to Chapter 5, Displaying Data, of the PanaView User’s
Manual.
48
DigitalFlow™ XGS868i Programming Manual
Chapter 2. Displaying Data
2.3.3
Displaying Transducer Signals
Along with flow rate data, PanaView enables XGS868i users to read and plot transducer signals from the XGS868i.
1.
2.
From the New Meter Browser, highlight the XGS868i.
Right-click on the highlighted XGS868i and click on the Properties option, as shown in Figure 5.
Figure 5: The Properties Option in the New Meter Browser
The Properties window opens, as shown in Figure 6.
Figure 6: The Properties Window
DigitalFlow™ XGS868i Programming Manual
49
Chapter 2. Displaying Data
2.3.3.1
Reading Transducer Signals
1. To read a signal from the meter, click on the [Read Signals] button. (If the meter is a multi-channel instrument, open
the Channel drop-down menu and click on the desired channel.) After a moment, the Properties window
appears similar to Figure 7.
Figure 7: Active Signal Options
2.
To select a different signal type, open the signal menu at the right (shown here with Raw Upstream highlighted)
and click on the desired signal.
2.3.3.2
Plotting Transducer Signals
To plot the selected signal, click on [Plot]. A graphical window opens, as shown in Figure 8.
Figure 8: Signal Graph Window
50
DigitalFlow™ XGS868i Programming Manual
Chapter 2. Displaying Data
2.3.3.3
Saving Transducer Signals
To save the raw signal, click on [Save]. A window opens similar to Figure 9. Enter the desired name, and click on [Save]
to save the signal as a text file.
Figure 9: Save As Window
DigitalFlow™ XGS868i Programming Manual
51
Chapter 2. Displaying Data
[no content intended for this page]
52
DigitalFlow™ XGS868i Programming Manual
Chapter 3. Logging Data
Chapter 3. Logging Data
3.1
Introduction
The XGS868i offers two options for logging data:
•
If the Model XGS868i flowmeter is equipped with an optional data logging card in Slot 2, flow rate data can be
recorded and stored in this memory in the form of a log file. After the specified data has been logged, the log file
may be uploaded to PanaView via the RS232 link.
•
PanaView can also create PC log files for storage on the PC’s hard drive.
This chapter explains how to use the Model XGS868i’s data logging capability with PanaView.
3.2
The Data Logging Option Card
In order to log data, the Model XGS868i must be fitted with an optional data logging option card in Slot 2. See Chapter
4, Parts Replacement, of the Service Manual for instructions on installing the card.
3.3
Logging via PanaView
PanaView is capable of creating and viewing log files of the following types:
•
•
meter logs - log files stored in the XGS868i memory, as discussed above
PC logs - log files stored on your PC’s hard drive (page 62)
To create or view logs of the above types, proceed to the appropriate section of this chapter.
DigitalFlow™ XGS868i Programming Manual
53
Chapter 3. Logging Data
3.4
Creating Meter Logs
To create a new meter log, complete the following steps:
1.
From the New Meter Browser in PanaView, expand the network tree and open the Edit Functions option
(described in Appendix C, Programming the XGS868i via PanaView). The menu will appear similar to Figure 10.
Figure 10: The Edit Functions Menu for an XGS868i with a Logging Card
2.
Double-click on the Log Edit Menu, as shown in Figure 10. The window appears similar to Figure 11.
Figure 11: The Log Edit Menu Window
54
DigitalFlow™ XGS868i Programming Manual
Chapter 3. Logging Data
3.4.1
1.
Creating a Standard Meter Log
To create a standard meter log, complete the following steps:
a.
Double-click on the Create Standard Log option.The window now appears similar to Figure 12.
Figure 12: Log Location in the Create Standard Log Option
b.
PanaView first asks for the Log Location, either flash or non-volatile RAM. Double-click on the desired location.
d.
Type the desired Log Message in the right window, and click [Next Item].
c.
e.
f.
g.
h.
Now type the desired Log Name in the right window, and click [Next Item].
PanaView now asks for the Number of Variables you wish to log. Type in the desired number (from 1 to 6), and
click [Next Item].
Double-click on the desired Channel for the first variable.
Scroll to and double-click on the desired Measurement to be logged.
Repeat steps f and g for the specified number of variables.
• If you select a forward or reverse total, PanaView asks if you want to Reset Totals to 0? Double-click on Yes
or No.
i.
PanaView indicates a given StartTime. Double-click on OK to agree to the given time, on Now to start the log
immediately, or on Edit to change the starting time.
• If you select Edit, PanaView asks first for the desired Hour, then for the Minute, and finally for the Second. For
each parameter, type the desired number in the right window, and click [Next Item] (or simply click [Next
Item] to step through the parameters).
j.
PanaView indicates a given StartDate. Double-click on OK to agree to the given day, on Today to start the log
that day, or on Edit to change the starting date.
• If you select Edit, PanaView asks first for the desired Year, then for the Month, and finally for the Day. For each
parameter, type the desired number in the right window, (or scroll to and click on the desired month) and
click [Next Item] (or simply click [Next Item] to step through the parameters).
k.
PanaView indicates a given End Time. Double-click on OK to agree to the given time, on Now to start the log
immediately, or on Timed to indicate a specific duration.
• If you select Edit, PanaView asks first for the desired Hour, then for the Minute, and finally for the Second. For
each parameter, type the desired number in the right window, and click [Next Item] (or simply click [Next
Item] to step through the parameters).
• If you select Timed, PanaView asks for the Log Time (duration). Scroll to and double-click on the desired
length of time (from 10 minutes to 24 hours.) Then go to step m.
l.
PanaView indicates a given End Date. Double-click on OK to agree to the given day, on Today to start the log
that day, or on Edit to change the starting date.
• If you select Edit, PanaView asks first for the desired Year, then for the Month, and finally for the Day. For each
parameter, type the desired number in the right window, (or scroll to and click on the desired month) and
click [Next Item] (or simply click [Next Item] to step through the parameters).
DigitalFlow™ XGS868i Programming Manual
55
Chapter 3. Logging Data
m. Scroll to and double-click on the desired Time Increment (from 5 seconds to 24 hours). PanaView indicates
that the log has been created, and returns to the Log Edit Menu.
If an erroneous value has been entered, PanaView displays a Log Creation Error message. Otherwise, the program
indicates that the log has been created, and returns to the Log Edit Menu.
3.4.2
Creating an Error Log
To create an error meter log, complete the following steps:
1.
Double-click on the Create Error Log option.
a.
PanaView first asks for the Log Location, either flash or non-volatile RAM. Double-click on the desired location.
c.
Type the desired Log Message in the right window, and click [Next Item].
b.
d.
e.
f.
g.
Now type the desired Log Name in the right window, and click [Next Item].
PanaView now asks for the Number of Variables you wish to log. Type in the desired number (from 1 to 6), and
click [Next Item].
Double-click on the desired Channel for the first variable.
Scroll to and double-click on the desired Measurement.
Repeat steps e and f for the specified number of variables.
• If you select a forward or reverse total, PanaView asks if you want to Reset Totals to 0? Double-click on Yes
or No.
h.
i.
PanaView asks, Is Log Circular? Double-click on Yes or No.
PanaView indicates a given StartTime. Double-click on OK to agree to the given time, on Now to start the log
immediately, or on Edit to change the starting time.
• If you select Edit, PanaView asks first for the desired Hour, then for the Minute, and finally for the Second. For
each parameter, type the desired number in the right window, and click [Next Item] (or simply click [Next
Item] to step through the parameters).
j.
PanaView indicates a given StartDate. Double-click on OK to agree to the given day, on Today to start the log
that day, or on Edit to change the starting date.
• If you select Edit, PanaView asks first for the desired Year, then for the Month, and finally for the Day. For each
parameter, type the desired number in the right window, (or scroll to and click on the desired month) and
click [Next Item] (or simply click [Next Item] to step through the parameters).
Note:
If you have selected a circular log, PanaView now indicates that the log has been created, and returns to the
Log Edit Menu.
k.
PanaView indicates a given End Time. Double-click on OK to agree to the given time, on Now to start the log
immediately, or on Timed to indicate a specific duration.
• If you select Edit, PanaView asks first for the desired Hour, then for the Minute, and finally for the Second. For
each parameter, type the desired number in the right window, and click [Next Item] (or simply click [Next
Item] to step through the parameters).
• If you select Timed, PanaView asks for the Log Time (duration). Scroll to and double-click on the desired
length of time (from 10 minutes to 24 hours.) Then go to step m.
l.
PanaView indicates a given End Date. Double-click on OK to agree to the given day, on Today to start the log
that day, or on Edit to change the starting date.
• If you select Edit, PanaView asks first for the desired Year, then for the Month, and finally for the Day. For each
parameter, type the desired number in the right window, (or scroll to and click on the desired month) and
click [Next Item] (or simply click [Next Item] to step through the parameters).
m. Scroll to and double-click on the desired Time Increment (from 5 seconds to 24 hours). PanaView indicates
that the log has been created, and returns to the Log Edit Menu.
If an erroneous value has been entered, PanaView displays a Log Creation Error message. Otherwise, the program
indicates that the log has been created, and returns to the Log Edit Menu.
56
DigitalFlow™ XGS868i Programming Manual
Chapter 3. Logging Data
3.4.3
Checking Log Memory
3.4.4
Stop Logging
3.5
Creating PC Logs
To check on the amount of log memory available, double-click on the Memory option in the Log Edit Menu. The right
window indicates the number of bytes available in both NVR and Flash memory.
To manually terminate logging, double-click on the Stop Logging option in the Log Edit Menu. PanaView displays the
name of the currently active logs. Double-click on your choice, and then click on Yes when the program asks if you
wish to stop logging.
PC logs are created in a different menu from the meter logs described in the last section. To create a new PC log:
1.
Open the Output menu (see Figure 13), and click on the Logging option.
Figure 13: Selections in the Logging Option
You have two choices:
• Click on the New PC Log option and proceed to step 5, or
• Click on the Log Browser option. The dialog box shown in Figure 14 appears.
Figure 14: Computer Selection
Note:
2.
If no log files have yet been created or if a log file has not yet been selected from the list, all of the option
buttons (except for [Cancel]) in the Log Browser dialog box are unavailable.
Double click on the computer name to advance to the dialog box shown in Figure 15 on page 58.
DigitalFlow™ XGS868i Programming Manual
57
Chapter 3. Logging Data
3.5
Creating PC Logs (cont.)
Figure 15: Log Type Selection
3.
Double click on PC Logs to advance to the dialog box shown in Figure 16.
Figure 16: Create a PC Log
4.
5.
At the dialog box shown in Figure 16, click on the [Create] option button to create a new meter log.
Enter a log file name (“Sample” in this case) in the dialog box shown in Figure 17. Click on the [OK] option button.
Figure 17: Log Name Dialog Box
58
DigitalFlow™ XGS868i Programming Manual
Chapter 3. Logging Data
3.5
6.
Creating PC Logs (cont.)
At the resulting PC Log window shown in Figure 18, place a check mark in the text box to create a circular log, or
leave this box empty to create a linear log.
Figure 18: The PC Log Window
7.
Enter a sampling interval in the text box shown in Figure 18.
Note:
8.
Expand the network tree as far as necessary and double click on the process parameter(s) to be logged. As they
are selected, the parameters are listed in the lower right pane of the PC Log window (make sure that the Log
Items tab in this pane is selected).
Note:
9.
Start Time and Stop Time cannot be specified for PC logs. These options are inactive in the PC Log window.
To add all the channel parameters to a given log, right-click on the desired channel. A pop-up button, “Add
Group to Log,” appears. Click on the button, and PanaView adds the entire set of channel parameters to the
log.
Click on the [Apply] option button to record the log setup information, and then click on the [Start] option button
to begin logging data immediately. (The Start Time automatically appears in the PC Log window.)
DigitalFlow™ XGS868i Programming Manual
59
Chapter 3. Logging Data
3.6
Viewing Meter Log Files
After one or more meter log files have been created, the logs may be viewed by using the New Meter Browser as
follows:
1.
From the New Meter Browser in PanaView, expand the network tree and click on the Meter Logs option. If you have
created one or more logs, the tree will appear similar to Figure 19.
Figure 19: An Expanded Meter Logs Option
2.
Double-click on the desired log. A window opens for the individual log, as shown in Figure 20.
Figure 20: Data Window for an Individual Meter Log
•
Click on the Log Items tab (see Figure 20) for a list of the parameters specified for logging.
•
Click on the Contents tab (see Figure 21 on page 61) for a list of all the data points logged to date for the
parameter currently highlighted on the Log Items tab.
•
Click on the [Graph] option button to display a graphical representation of the data logged to date.
60
DigitalFlow™ XGS868i Programming Manual
Chapter 3. Logging Data
3.6
Viewing Meter Log Files (cont.)
Note:
The graph is displayed in its own window, which is opened on top of the Meter Log window. For instructions
on using the Graph Log window, refer to the Graphing Output section in Chapter 2 of the PanaView User’s
Manual.
Remember that only two parameters per channel may be graphed, and that the same two parameters must be
graphed for each channel of a multi-channel graph display. When you have finished viewing the graph, click on the
[Close] option button to close the Graph window and leave the log running.To review log details, click on the
Contents tab. The window now appears similar to Figure 21.
Figure 21: Typical Log Contents
DigitalFlow™ XGS868i Programming Manual
61
Chapter 3. Logging Data
3.7
Viewing PC Log Files
After one or more PC log files have been created, the logs may be viewed by using PanaView as follows:
1.
You can access PC logs in two ways:
• From the New Meter Browser in PanaView, expand the network tree and click on the PC Logs option. If you have
created one or more logs, the tree will appear similar to Figure 22 below. Double-click on the log name to open
the log, or
• Pull down the Output menu (see Figure 13 on page 57), and click on the Log Browser option. Advance to the PC
Logs dialog box as described in previous sections. A screen similar to that shown in Figure 23 appears.
Figure 22: The Expanded PC Logs Option
Figure 23: Selecting a Log File from the Log Browser
Notice that each of the log files in Figure 22 and Figure 23 has a traffic light icon next to its name. These icons indicate
the current status of the log as follows:
•
red light - log has not run to its specified stop time but has been manually stopped
•
green light - log is currently running but is not yet complete
62
DigitalFlow™ XGS868i Programming Manual
Chapter 3. Logging Data
3.7
2.
Viewing PC Log Files (cont.)
In the Log Browser, after you highlight the name of the desired log file, the following option buttons become
available:
• [Start] - resumes logging if the log is currently stopped
• [Stop] - stops logging, if the log is currently running
• [Delete] - permanently deletes the log file
3.
• [Open] - opens the log in the PC Log window
Click on one of the option buttons listed in Step 2 above.
You can monitor the progress of an ongoing log in several ways:
•
Click on the Log Items tab (see Figure 21 on page 61) for a list of the parameters specified for logging.
•
Click on the Contents tab (see Figure 21 on page 61) for a list of all the data points logged to date for the
parameter currently highlighted on the Log Items tab.
•
Click on the [Graph] option button to display a graphical representation of the data logged to date.
Note:
•
The graph is displayed in its own window, which is opened on top of the PC Log window. For instructions on
using the Graph Log window, refer to the Graphing Output section in Chapter 2 of the PanaView User’s
Manual.
Click on the [Refresh] option button to update the information shown on the Contents tab and in the Graph Log
window. Any data logged since the last use of the [Refresh] option button is added to the list and to the graph.
Remember that only two parameters per channel may be graphed, and that the same two parameters must be
graphed for each channel of a multi-channel graph display. When you have finished viewing the graph, click on the
[Close] option button to close the Graph window and leave the log running.
4.
To terminate the logging process, simply click on the [Stop] option button, which has replaced the original
[Start] option button. (The Stop Time automatically appears in the PC Log window.)
Because a PC log has no specific “Stop Time,” the log will continue to run until it is manually stopped (unless the PC is
turned off or you run out of hard drive space).
DigitalFlow™ XGS868i Programming Manual
63
Chapter 3. Logging Data
[no content intended for this page]
64
DigitalFlow™ XGS868i Programming Manual
Chapter 4. Printing Data
Chapter 4. Printing Data
4.1
Data Types for Printing
The Model XGS868i flowmeter has no ability to print any of its data directly. However, any of the data stored in its
memory may be printed via the built-in RS232 communications port, using a computer terminal. In order to use the
capability, the XGS868i must be linked to the computer terminal with the optional PanaView software.
Note:
See Chapter 1, Installation, of the Startup Guide for instructions on wiring the RS232 serial port. For additional
information, refer to the EIA-RS Serial Communications Manual (916-054).
After making the hardware connections and installing PanaView software, the following data may be output to a
printer connected to the personal computer:
•
live data in numeric or graphical format
•
log file in numeric or graphical format
•
site file in tabular format
•
transducer signal array data in tabular format
For detailed instructions on printing any of the data types listed above, consult the PanaView User’s Manual.
DigitalFlow™ XGS868i Programming Manual
65
Chapter 4. Printing Data
[no content intended for this page]
66
DigitalFlow™ XGS868i Programming Manual
Chapter 5. Clearing Data
Chapter 5. Clearing Data
5.1
Introduction
This chapter explains how to purge totalized measurements, site data and/or log files from the XGS868i’s memory.
Note:
For detailed information on creating a log file, see Chapter 3, Logging Data. For detailed information on
programming site data, see Chapter 1, Programming Site Data.
IMPORTANT: None of the clearing procedures described in this chapter can be undone. Be very sure that the exact
consequences of a selected option are thoroughly understood before proceeding.
5.2
Clearing the XGS868i’s Memory
If the XGS868i’s available memory becomes nearly full, it may be necessary to purge some or all of the existing data
from memory, before any additional data can be stored. In order to accomplish this task, proceed to the appropriate
section for step-by-step instructions.
Note:
Depending on the current configuration of the XGS868i, it may be possible to add additional memory by
installing an option card in Slot 2. See Chapter 4, Parts Replacement, of the Service Manual for details.
5.2.1
Clearing Site Data
This feature has not yet been implemented, because the XGS868i currently has no capability to store site files in its
own memory.
DigitalFlow™ XGS868i Programming Manual
67
Chapter 5. Clearing Data
5.2.2
Clearing Log Files
To clear log files from the XGS868i or from the PC’s memory, complete the following steps:
1.
From PanaView, click on the Logging option in the Output menu. Then click on the Log Browser option, as shown in
Figure 24.
Figure 24: The Log Browser in the Logging Option
2.
3.
Double-click on the computer name to move to the network level.
Double-click on PC Logs to access the stored PC logs, or on the communication port name and the meter name
to access the stored meter logs. In either case, the Log Browser appears similar to Figure 25.
Figure 25: Log Browser Window
4.
68
Highlight the log you wish to delete, and click on the [Delete] option button.
DigitalFlow™ XGS868i Programming Manual
Chapter 5. Clearing Data
5.2.3
Clearing the Totalizers
You can clear the XGS868i’s totalizers (i.e., reset specified totalized flow rates to zero) from either the LCD display (see
Appendix A) or from PanaView (see Appendix D). To reset totals from the display, complete the following steps:
1.
2.
3.
Press [Escape], [Enter], [Escape].
In the Keypad Program, scroll to RESET and press [Enter].
The XGS868i asks Reset Totals? Scroll to NO or YES (2) and press [Enter] at the desired choice.
The XGS868i totalizers are reset to 0, and the meter returns to the Keypad Program. Press [Escape] to return to the data
display.
To reset the totals from PanaView:
1.
2.
From the New Meter Browser in PanaView, highlight the XGS868i.
Open the Edit menu and select the Properties option, as shown in Figure 26.
Figure 26: The Properties Option in the Edit Menu
3.
The Properties window appears similar to Figure 27. To clear the XGS868i totalizers, click on the [Clear Totalizers]
button. The XGS868i totalizers are reset to 0.
Figure 27: The Properties Window
DigitalFlow™ XGS868i Programming Manual
69
Chapter 5. Clearing Data
[no content intended for this page]
70
DigitalFlow™ XGS868i Programming Manual
Appendix A. Menu Maps
Appendix A. Menu Maps
DigitalFlow™ XGS868i Programming Manual
71
Appendix A. Menu Maps
72
DigitalFlow™ XGS868i Programming Manual
[Esc]
[Enter]
[Esc]
Keypad Pgm.
PROG
RESET
CALIB
CNTRS
CH1
See Service Manual
CH2*
GLOBL
NO
SYSTM
YES
I/O
COMM
DARKN
LITEN
STORE
ABORT
SECUR
See Figure 30
ACTIV
SYSTM
PIPE
2-Channel
1-Channel
ASSUME SATURATION
STD
Site Status
Burst
Burst
Skan Only
See Figure A-2
SPEC
VOLUMETRIC UNITS
No
SPECIAL TRANSDUCER
English Metric
Yes
FREQUENCY
100k
50k
Skan/Measure Mode
SET UP
ZERO CUTOFF
SITE/CHANNEL MESSAGE
Channel Status
Off
I/O
TRANSDUCER NUMBER
CHANNEL LABEL
ACF
KACF
MMACF
ACM
KACM
MMACM
SCF
KSCF
MMSCF
SCM
KSCM
MMSCM
STEAM INPUT TYPE
200k
500k
25k
Temperature
33k
Tw
Skan/Measure
TEMP INPUT
(*only if input option is installed)
PIPE OD
Fixed
English Metric
Slot1*
A:LABEL B:LABEL
VOLUMETRIC TIME
MASS FLOW UNITS
English Metric
MASS FLOW ON
inch
MASS FLOW OFF
/SEC
/MIN
/HR
feet
in/PI
ft/PI
mm
m
mm/PI
m/PI
KLB
MMLB
TONS
KG
PATH LENGTH P
VOL. DECIMAL DIGITS
TONNE
0
1
Steam Input Type = Temp
English Metric
2
B
FIXED TEMP.
PIPE WALL
LB
A
/DAY
BASE TEMP.
PRESSURE INPUT
(*only if input option is installed)
3
Fixed
inch
MASS FLOW TIME
feet
mm
Slot1*
m
A:LABEL B:LABEL
TOTALIZER UNITS
/SEC
/MIN
/HR
/DAY
English Metric
AXIAL LENGTH L
English Metric
A
FIXED PRESSURE
MDOT DECIMAL DIGITS
0
1
B
2
ACF
KACF
MMACF
ACM
KACM
MMACM
SCF
KSCF
MMSCF
SCM
KSCM
MMSCM
3
inch
MASS TOTALS
English Metric
feet
mm
BASE PRESSURE
m
Pressure
Figure 28: Channel-Status, System, Pipe Parameters & Input/Output Menu Map
Reset Totals
(* for 2-Channel meter only)
Low Pressure Switch
NO
FLUID TYPE
YES
PRESSURE LIMIT
Steam
TOTAL DECIMAL DIGITS
LB
KLB
MMLB
TONS
KG
Other
FLUID SOUNDSPEED
TONNE
0
1
2
3
QUALITY INPUT
F1
F2
Fixed
Slot1
REYNOLDS CORRECTION
A:LABEL B:LABEL
MASS DECIMAL DIGITS
Off
On
A
KINEMATIC VISCOSITY
0
1
2
3
CALIBRATION FACTOR
DigitalFlow™ XGS868i Programming Manual
B
FIXED QUAL.
73
[Esc]
[Enter]
[Esc]
Keypad Program
PROG
RESET
CALIB
CNTRS
Reset Totals
(* for 2-Channel meter only)
CH1
See Service Manual
CH2*
GLOBL
NO
SYSTM
YES
I/O
DARKN
LITEN
STORE
ABORT
SECUR
COMM
Status
System
Pipe Parameters
Input/Output
See Figure 28
See Figure 28
See Figure 28
See Figure 28
Signal
V averaging
Default Setup
Signal Defaults?
See Figure 30
SET UP
Advanced Features
RESPONSE TIME
SIGNAL LOW LIMIT
NO
CORR. PEAK LIMIT
YES
1
2
5
30
60
STATS
Multiple K Factors
SKAN T OFFSET
SOUNDSPEED + – LIMIT
% OF PEAK
VELOCITY LOW LIMIT
M>S SWITCH
10
Mass Flow Calculation
Activate Multi K Fact?
Off
Mass from Static Dens?
No
On
Custom Type
VELOCITY HIGH LIMIT
Yes
Fluid Density
# SHIFTS
CstV
ACCELERATION LIMIT
A DIVISOR
AMP. DISCRIM LOW
# TRANSMIT PULSES
AMP. DISCRIM HIGH
T WINDOW
R WINDOW
CstR
Kin. Viscosity
Edit table?
NO
DELTA T OFFSET
Figure 29: Channel-SETUP Menu Map
See Figure 30
YES
Enter # of K Factors
Velocity (Reynolds) #*
K Factor #*
*Repeat for the # of K Factors entered previously.
DigitalFlow™ XGS868i Programming Manual
74
[Esc]
[Enter]
[Esc]
Keypad Pgm.
PROG
RESET
CALIB
CNTRS
Reset Totals
(* for 2-Channel meter only)
CH1
See Service Manual
CH2*
GLOBL
NO
DARKN
LITEN
STORE
ABORT
YES
SYSTM
METER MESSAGE
I/O
Meter Address
SYSTEM UNITS
BAUD RATE
Eng
ERROR
Metric
OPTN
LCD
See Figure A-4
PRESSURE UNITS
English Metric
PSIa
PSIg
BARa
SECUR
COMM
BARg
Kpaa
HIGH
HOLD
LOW
HHIGH
OTHER
300
600
1200
4800
9600
19200
2400
Kpag
MODBUS option installed
1-CHANNEL UNITS
ATMOSPHERIC PRESSURE
2 PATH ERROR HANDLING
1-CHANNEL UNITS
MASS FLOW UNITS
English Metric
MASS FLOW ON
MASS FLOW OFF
MODBUS Baud Rate
2-CHANNEL UNITS
2-CHANNEL UNITS
VOLUMETRIC UNITS
English Metric
YES
2400
4800
9600
19200
NO
MODBUS Parity
# OF LCD PARAMS
LB
KLB
MMLB
TONS
KG
TONNE
ACF
KACF
MMACF
ACM
KACM
MMACM
OFF
SCF
KSCF
MMSCF
SCM
KSCM
LOCK OUT
None
1
3
2
4
Odd
Even
UNlck
KEY
LOCK
ENTER PASSWORD
MMSCM
? EDIT PASSWORD
MODBUS Stop Bits
(appears only for 2-Channel meter)
MASS FLOW TIME
/SEC
/MIN
/HR
1 Bit
VOLUMETRIC TIME
/DAY
/SEC
/MIN
(until all channels set up)
CH1
/HR
CH2
SUM
DIF
MODBUS Address
Measurement Name
VOL DECIMAL DIGITS
1
2
3
0
MASS TOTALS
English Metric
LB
KLB
MMLB
TONS
KG
1
2
ACF
SCF
KACF
KSCF
MMACF
MMSCF
ACM
SCM
KACM
KSCM
MASS DECIMAL DIGITS
0
1
2
3
TOTAL DECIMAL DIGITS
0
DigitalFlow™ XGS868i Programming Manual
VEL
3
TOTALIZER UNITS
English Metric
TONNE
1
2
NO
YES
ENTER NEW PASSWORD
VERIFY NEW PASSWORD
/DAY
MDOT DECIMAL DIGITS
0
2 Bits
AVE
VOLUM +TOTL
–TOTL
TIME
MDOT
+MASS –MASS
SS up
SS do
SNDSP
T up
Tdown
DELTA
REYN#
Tot K
PEAK%
Qup
Qdown
AMPup
AMPdn
CNTup
CNTdn
P#up
P#dn
TEMP
PRESR
Z
AcVOL
StVOL
Vinst
Tsat
Tsupr
Rho
Kelvn
kPa
MMACM
Figure 30: Global-System, I/O (Error Handling/Display), Comm Port Menu Map
See Figures 28 and 29
MMSCM
QUAL
3
75
[Esc]
[Enter]
Keypad Pgm.
[Esc]
PROG
RESET
CALIB
CNTRS
Reset Totals
(* for 2-Channel meter only)
CH1
See Service Manual
CH2*
NO
GLOBL
YES
DARKN
LITEN
STORE
ABORT
See Figures 28 and 29
SYSTM
I/O
See Figure 30
Error Handling
COMM
SECUR
See Figure 30
See Figure 30
Display
Options
See Figure 30
See Figure 30
I/O (appears only if option card is installed)
SLOT0
SLOT1
Analog Outputs
A
Totalizer Outputs
Frequency Outputs
B
A
B
C
A
D
Alarm Relays
C
B
D
A
B
C
D
LOW
FAULT
Slot 0 Output A
Slot 1 Outputs
Off
0-20m
4-20m
Slot 1 Outputs
Slot 1 Outputs
FREQ
OFF
Channel
OFF
(appears only for 2-Channel meter)
TTLZR
OFF
Channel
CH1
CH2
SUM
DIF
AVE
Channel
Measurement Name
CH1
CH2
(appears only for 2-Channel meter)
SUM
DIF
CH1
CH2
HIGH
(appears only for 2-Channel meter)
SUM
DIF
Failsafe?
AVE
NO
AVE
YES
Measurement Name
VEL
VOLUM
+TOTL
–TOTL
TIME
MDOT
A
+MASS
–MASS
SS up
SS do
SNDSP
Measurement Name
B
T up
+TOTL
–TOTL
+MASS
–MASS
VEL
VOLUM
+TOTL
–TOTL
TIME
MDOT
+MASS
–MASS
SS up
SS do
SNDSP
T up
Tdown
DELTA
REYN#
Tot K
PEAK%
Qup
Qdown
AMPup
AMPdn
CNTup
CNTdn
P#up
P#dn
TEMP
PRESR
Z
AcVOL
StVOL
Vinst
Tsat
Tsupr
Rho
Kelvn
kPa
Channel (appears only for 2-Channel meter)
CH1
Slot 1 Outputs
Tdown
DELTA
REYN#
Tot K
PEAK%
Qup
Off
Qdown
AMPup
AMPdn
CNTup
CNTdn
0-20m
TEMP
PRESR
Z
AcVOL
Tsat
Tsupr
Rho
Kelvn
(appears only for 2-Channel meter)
StVOL
CH1
Vinst
UNITS/PULSE
4-20m
P#up
Channel
P#dn
MINIMUM ON
PULSE TIME
kPa
CH2
SUM
DIF
QUAL
B
C
–TOTL
TIME
MDOT
OFF
–MASS
SS up
SS do
SNDSP
DELTA
REYN#
Tot K
PEAK%
FLOW
OTHER
ALL
QUAL
T up
HIGH/LOW
Measurement Name
VEL
VOLUM
+TOTL
–TOTL
TIME
MDOT
+MASS
–MASS
SS up
SS do
SNDSP
T up
Tdown
DELTA
REYN#
Tot K
PEAK%
Qup
Qdown
AMPup
AMPdn
CNTup
CNTdn
P#up
P#dn
TEMP
PRESR
Z
AcVOL
StVOL
Vinst
Tsat
Tsupr
Rho
Kelvn
kPa
Analog Inputs
High
A
Tdown
Fault Type
FULL
TEMP
Low
+MASS
FAULT
BASE
FULL SCALE FREQUENCY
+TOTL
AVE
D
Input measurement
VOLUM
DIF
LABEL
Measurement Name
VEL
SUM
RTD Inputs
A
AVE
CH2
Figure 31: Global-Input/Output, Options Menu Map
Slot 0 Outputs
B
C
D
Qup
LABEL
NOTE: Plain text represents prompt area messages and
boxed text represents option bar choices.
Fx represent function keys to select option bar choices.
Qdown
AMPup
AMPdn
CNTup
CNTdn
P#up
P#dn
TEMP
PRESR
Z
AcVOL
StVOL
Vinst
Tsat
Tsupr
Rho
Kelvn
kPa
Input measurement
OFF
PRESR
TEMP
SPEC
INPUT NAME
QUAL
QUAL
INPUT UNITS
ZERO Value
ZERO
FULL
DigitalFlow™ XGS868i Programming Manual
FULL Scale Value
Trigger point
(All diagnostic parameters
appear here.)
76
Appendix B. Data Records
Appendix B. Data Records
B.1
Available Option Cards
The Model XGS868i can hold one option card in Slot 1 and one in Slot 2. The available configurations are listed in
Table 14.
Table 14: Option Card Configurations
Card #
Slot #
1215-02
1
Configuration
FF - 4 Frequency Outputs
1215-03
TT - 4 Totalizer Outputs
1215-04
FT - 2 Frequency Outputs/2 Totalizer Outputs
1215-05
FO - 2 Frequency Outputs
1215-06
TO - 2 Totalizer Outputs
1215-07
AA - 4 Standard Alarms
1215-09
FA - 2 Frequency Outputs/2 Standard Alarms
1215-11
TA - 2 Totalizer Outputs/2 Standard Alarms
1223-02
OI - 2 Current Inputs
1430-04
OR - 2 RTD Inputs
1223-04
TI - 2 Current Inputs/2 Totalizer Outputs
1473-05
TR - 2 RTD Inputs/2 Totalizer Outputs
1223-06
FI - 2 Current Inputs/2 Frequency Outputs
1473-07
FR - 2 RTD Inputs/2 Frequency Outputs
1223-08
AI - 2 Current Inputs/2 Standard Alarms
1473-10
AR - 2 RTD Inputs/2 Standard Alarms
1225-13
CO - 2 Current Outputs
1225-14
CF - 2 Current Outputs/2 Frequency Outputs
1225-15
CT - 2 Current Outputs/2 Totalizer Outputs
1225-16
CA - 2 Current Outputs/2 Standard Alarms
1430-03
RR - 4 RTD Inputs
1430-04
IR - 2 RTD Inputs/2 Current Inputs
1233-02
1146-02
II - 4 Current Inputs
2
512 KB Memory + PCMCIA Card Connector
1146-03
2 MB Memory + PCMCIA Card Connector
1310-02
Modbus Communications Protocols
DigitalFlow™ XGS868i Programming Manual
77
Appendix B. Data Records
B.2
Option Cards Installed
Whenever an option card is installed or changed in the Model XGS868i flow transmitter, record the type of card and
any additional setup information in the appropriate row of Table 15.
Table 15: Option Cards Installed
Slot #
Type of Option Card
0
Analog Outputs (A, B)
Additional Setup Information
1
2
78
DigitalFlow™ XGS868i Programming Manual
Appendix B. Data Records
B.3
Setup Data
After the Model XGS86i flow transmitter has been installed, setup data must be entered via the User Program prior to
operation. Record that information in Table 16.
Table 16: Setup Data
General Information
Model #
Serial #
Software Vers.
Setup Date
Global - System
Meter Message
System Units
Tot. Dec. Digits
English
Metric
Mass Flow
Pressure Units
Mass Flow Time
Vol. Units
MDOT Dec. Digit
Vol. Time Units
Mass Totals
Vol. Dec. Digits
Mass Dec. Digits
Totalizer Units
Global - Input/Output - Error Handling
Error Handling
2-Path Error
Global - Communications Port
Meter Address
MOD. Parity
Baud Rate
MOD. Stop Bits
MOD. Baud Rate
MOD. Address
No
Yes
Channel - Status
Channel 1
Channel 2
Channel Status
Off
Burst
Channel Status
Off
Burst
Measure Mode
Skan
S/M
Measure Mode
Skan
S/M
Channel - System
Channel Label
Channel Label
Site/Channel
Msg.
Channel
Message
Vol. Units
Vol. Units
Vol. Time Units
Vol. Time Units
Vol. Dec. Digits
Vol. Dec. Digits
Totalizer Units
Totalizer Units
Tot. Dec. Digits
Tot. Dec. Digits
Mass Flow
Mass Flow
Mass Flow Time
Mass Flow Time
MDOT Dec. Dig.
MDOT Dec. Dig.
Mass Totalizer
Mass Totalizer
Mass Dec. Dig.
Mass Dec. Dig.
Channel - Pipe Parameters
Channel 1
Trans. Type
STD
DigitalFlow™ XGS868i Programming Manual
Channel 2
SPEC
Trans. Type
STD
SPEC
79
Appendix B. Data Records
Transducer #
Table 16: Setup Data
Transducer #
Spec. Trans. Hz
Spec. Trans. Hz
Spec. Trans. Tw
Spec. Trans. Tw
Pipe O.D.
Pipe O.D.
Pipe Wall
Pipe Wall
Path Length (P)
Path Length (P)
Axial Length (L)
Axial Length (L)
Fluid Type
Steam
Other
Other/Sndspd
Calibration
Factor
Calibration
Factor
Steam
Other
Channel - Input/Output
Zero Cutoff
Zero Cutoff
Assume Sat.
No
Yes
Assume Sat.
No
Yes
Steam Input
Type
Temp
Pressure
Steam Input
Type
Temp
Pressure
No
Yes
Temp. Input
Temp. Input
Base Temp.
Base Temp.
Pressure Input
Pressure Input
Base Pressure
Base Pressure
Low Press. Switch
No
Yes
Low Press. Switch
Pressure Limit
Pressure Limit
Quality Input
Quality Input
Response Time
K-Factor #
Channel - SETUP - V Averaging
Response Time
Channel - SETUP - Advanced Features - Multi K Factors
Velocity
K-Factor
K Factor #
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
Velocity
K-Factor
Channel - SETUP - Advanced Features - Multi K Factors (cont.)
K-Factor #
80
Fluid Type
Other/Sndspd
Velocity
K-Factor
K Factor #
Velocity
K-Factor
11
12
12
13
13
DigitalFlow™ XGS868i Programming Manual
Appendix B. Data Records
14
Table 16: Setup Data
14
15
15
16
16
17
17
18
18
19
19
20
20
DigitalFlow™ XGS868i Programming Manual
81
Appendix B. Data Records
[no content intended for this page]
82
DigitalFlow™ XGS868i Programming Manual
Appendix C. Programming the XGS868i Using PanaView™
Appendix C. Programming the XGS868i Using PanaView™
C.1
Introduction
The Model XGS868i flow transmitter must be properly installed and programmed, as described in the Startup Guide,
before it can provide accurate flow rate measurements. After completing the installation and initial setup, use this
chapter to program the advanced features of the Model XGS868i’s via the PanaView™ software program. Refer to the
appropriate section for a discussion of the following menu features:
•
Channel-Status - activate one or both channels and select the desired measurement method
•
Channel-System - enter the individual channel parameters
•
Channel-Pipe - enter the pipe parameters
•
Channel-I/O - set up the inputs and outputs
•
Channel-Setup - set the signal limits, response times and activating mass flow.
•
Global-System - enter the system units
•
Global-I/O - set up error handling, option cards and display
•
Global-Comm - set the serial port and MODBUS parameters
As a programming aid, a complete set of menu maps for the PROG menu is included in Appendix D, PanaView Menu
Maps. The specific figure numbers will be referenced throughout this chapter, as required.
C.2
Programming with PanaView™
You can program the XGS868i through PanaView™, a PC-based, non-resident software program that communicates
with the XGS868i via its RS232 serial port.
C.2.1
Preparing for PanaView Programming
Before you attempt to communicate with the XGS868i, be sure you have linked your PC to the XGS868i via an RS232
interface. For details on wiring the interface, refer to Wiring the Serial Port in the Startup Guide, and to the document
EIA-RS Serial Communications (916-054). You must also install PanaView, as discussed in the PanaView User’s
Manual (910-211).
DigitalFlow™ XGS868i Programming Manual
83
Appendix C. Programming the XGS868i Using PanaView™
C.2.2 Setting Up the Communications Port
Use the steps below to establish PanaView communications with the XGS868i.
1.
2.
3.
4.
Launch PanaView, as discussed in Chapter 3, Initial Setup, of the PanaView User’s Manual.
Open the New Meter Browser window in the File menu and expand the network tree. Then, highlight the My Computer (Name) branch by clicking on it.
Pull down the Edit menu by clicking on it in the menu bar.
Click on the New menu option to select it, and a submenu opens with two choices on it (see Figure 32).
Figure 32: The Edit Menu
84
DigitalFlow™ XGS868i Programming Manual
Appendix C. Programming the XGS868i Using PanaView™
C.2.2 Setting Up the Communications Port (cont.)
5.
Click on the Communications Port option to select it. The Setup Communications screen appears similar to
Figure 33.
Figure 33: Setup Communications Screen
6.
7.
Open the Protocol menu (the first of the drop-down menus) and click on IDM.
Open the COM Port Type menu and click on the desired type (or on TCP/IP, if the XGS868i is using an Ethernet
connection).
Note: If you select TCP/IP, the menu changes. Proceed to the next page.
8.
Select any suitable available baud rate. A baud rate of 19,200 is appropriate for almost all applications. However,
if you experience periodic communication reliability problems, you may wish to consider lowering the baud rate
on your instrument and in PanaView.
IMPORTANT: Be sure all the communications port settings match those made in setting up the meter’s serial port.
9.
Click on [OK] to complete data entry.
DigitalFlow™ XGS868i Programming Manual
85
Appendix C. Programming the XGS868i Using PanaView™
C.2.3 Setting up Ethernet Communications
If you have selected TCP/IP in step 6 on the previous page, the Setup Communications window appears similar to
Figure 34.
Figure 34: Setup Communications for TCP/IP
1.
2.
Type in the desired Name and Timeout (in milliseconds).
In the IP Address text box, enter the IP address. If the IP address is unknown, run the Device Discovery software
utility. All units found will be identified by their MAC address and the assigned IP address. In the Port Number box,
enter 2101 (the default value).
3. Click [OK] to complete data entry.
IMPORTANT: If you are using Ethernet communications, be sure the XGS868i is set up with the default
communications parameters: 9600 baud, no parity, no handshaking, 8 data bits and 1 stop bit. The
port number must match the “Enable Raw TCP access using TCP Port” assignment shown under the
Device Discovery “TCP Server Settings” menu (Configuration>Serial Ports>Port).
86
DigitalFlow™ XGS868i Programming Manual
Appendix C. Programming the XGS868i Using PanaView™
C.2.4 Modifying Ethernet Parameters
To establish Ethernet communications with the XGS868i or to modify its IP parameters, you will need to install the
Ethernet Device Discovery software utility (available with your XGS868i) on a PC connected to the LAN. Once installed
and running, the software displays all Ethernet devices currently connected to the subnet. You can identify the
XGS868i by its MAC address, supplied as part of customer documentation. The default IP Port is 2101.
The default IP addressing for the XGS868i is DHCP (dynamic). If you need to assign a static IP address to the XGS868i,
complete the following steps:
IMPORTANT:
1.
2.
3.
To assign a static IP address, the XGS868i must be connected to an Ethernet network with a dynamic
address assignment mechanism (DHCP) first.
Run Ethernet Device Discovery software, and identify the XGS868i’s current IP address.
Open your Internet browser (Internet Explorer, Netscape, or other) and type the XGS868i IP address in the Address
box.
The Connect ME Configuration and Management window opens. Two text boxes ask for the user name and password.
a. In the Username text box, type root.
b. In the Password text box, type dbps.
4.
5.
6.
At the left of the window, click on Network.
The IP Settings window opens. In the text boxes for IP Address, Subnet Mask, and Default Gateway, type in the new
information.
Click Apply. The software applies the new address.
DigitalFlow™ XGS868i Programming Manual
87
Appendix C. Programming the XGS868i Using PanaView™
C.3
Adding the XGS868i
To add the XGS868i on the IDM-configured communications port, complete the following steps:
1.
2.
Highlight the communication port to which the meter will be added by clicking on it, and then open the Edit menu
on the menu bar (if the communication port is not highlighted first, the New Meter option is not active in the Edit
menu).
Click on the New option in the Edit menu (see Figure 35).
Figure 35: New Option in the Edit Menu
3.
4.
After clicking on the New option, the Meter menu option appears. Click on this option to select it.
The New IDM Meter screen (shown in Figure 36) opens. Enter the Network ID number for the meter, and click [OK].
Figure 36: New IDM Meter Screen
88
DigitalFlow™ XGS868i Programming Manual
Appendix C. Programming the XGS868i Using PanaView™
C.3
Adding the XGS868i (cont.)
IMPORTANT:
The Network ID number must match the Network ID programmed in the meter’s Communications
menu.
If the initialization is successful, the Meter Browser shows a listing similar to Figure 37.
Figure 37: The Updated Network Tree
However, if the settings do not match, or there is some other difficulty, a screen appears similar to Figure 38.
Figure 38: Communication Error Screen
The screen offers the options of trying again or of canceling the operation. Click on the desired choice, and then on
[OK] to confirm the choice or on [Exit Application] to close PanaView.
DigitalFlow™ XGS868i Programming Manual
89
Appendix C. Programming the XGS868i Using PanaView™
C.4
Entering the User Program using PanaView
Note:
Be sure to record all the programming data entered in this chapter in Appendix B, Data Records.
Programming of the Status, System, and Pipe submenus of the Channel menu and the Global-System menu are
required for basic operation of the Model XGS868i. Failure to accurately enter all of the necessary information will
result in unreliable flow rate data. Therefore, be sure to complete at least the sections of this chapter pertaining to
those three submenus. Except for those three submenus, it is not necessary to program the Model XGS868i flowmeter
in any particular order. Therefore, the sections of this chapter need not be completed in sequence. Enter the user
program as described below and proceed immediately to any section of interest.
To begin entering data into the XGS868i using PanaView:
1.
From the meter tree in the New Meter Browser (shown in Figure 37 on page 89), click on the XGS entry. The screen
now appears similar to Figure 39.
Figure 39: Meter Tree with Edit Functions Option
2.
90
Expand the Edit Functions option. The window now appears similar to that shown in Figure 40 on page 91.
DigitalFlow™ XGS868i Programming Manual
Appendix C. Programming the XGS868i Using PanaView™
C.4
Entering the User Program using PanaView (cont.)
Figure 40: Menus in the Edit Functions Option
3. To enter data into the user program, double-click on the Site Edit Menu. The window appears similar to Figure 41.
Note: For a 1-Channel XGS868i, the Channel 2 option does not appear.
Figure 41: The Site Edit Menu Window
4.
5.
To enter a particular menu (Channel 1, Channel 2, or Global), highlight and double-click on the desired menu in the
left pane. For example, clicking on Channel 1 in Figure 40 opens the list of options shown in the center pane.
To enter a particular option:
a. Highlight and double-click on the desired option in the center pane. Figure 42 on page 92 shows the first
entry (Transducer Number) in the Pipe Parameters option. The title above the center pane lists the current
entry, while the center pane displays the available selections for that entry.
b. Click on the desired choice; if the entry requires a numeric or text value, change the value displayed in the
right pane.
DigitalFlow™ XGS868i Programming Manual
91
Appendix C. Programming the XGS868i Using PanaView™
C.4
Entering the User Program using PanaView (cont.)
Figure 42: Pipe Parameters Option in the Site Edit Menu
c. Do one of the following:
Click on [Next Item] to proceed to the next menu item, or
Click on [Previous Item] to return back through the menu to a previous item.
Note:
If you click on either [Next Item] or [Previous Item] without changing the settings, the current settings remain
unchanged.
As you step through the menu, the bottom panel lists the current settings you have modified or left unchanged, as
shown in Figure 43. If you modify or step through more than five items, a scroll bar at the right of the panel lets you
review the earlier settings.
Figure 43: Site Edit Menu with Current Settings
When you have completed entering parameters in a given option, click [Exit Page] to close the option. You can
then double-click on another option, or click [Close] to close the window.
You can double-click on another menu to modify its settings, or return to the New Meter Browser. Proceed to the
following sections to enter data in the Channel or Global menus.
6.
92
DigitalFlow™ XGS868i Programming Manual
Appendix C. Programming the XGS868i Using PanaView™
C.5
Entering Data in the Channel Menu
The Channel menu is used to enter data specific to each channel. Refer to Figure 55 on page 129 and Figure 56 on
page 130 in Appendix D, PanaView Menu Maps, and remember to record all programming data in Appendix B, Data
Records.
Note:
In this manual, only the programming of Channel 1 will be described. To program Channel 2 of a 2-Channel
meter, simply repeat the same procedures presented for Channel 1.
C.5.1 Selecting the Channel Measurement Method
The Status submenu permits selection of the desired measurement method.
1.
2.
In the Site Data Menu, double-click on the desired channel.
Highlight and double-click on the Status option in the center pane. The window now appears similar to Figure 44.
Figure 44: The Status Option in the Channel Menu
3. Double-click on Burst to activate the channel/path.
Note: Burst is automatically selected for a 1-Channel meter.
4.
Double-click on one of the measurement methods described below.
•
Skan Only is the preferred technique for locating the acoustic signal and for high velocity measurements. It is
more robust in a noisy environment than the Measure technique.
•
Skan/Measure is the preferred technique to use for low velocity measurements.
If Skan Only is selected at the above prompt, the meter uses this technique exclusively. However, if Skan/Measure is
selected, the meter uses Skan Only to find the acoustic signal and then tries to use the Skan/Measure technique for the
actual measurement.
Note:
To change the Skan Only and Skan/Measure parameters, see the Signal submenu section on page 14.
PanaView returns to the Channel PROGRAM menu shown in Figure 41 on page 91. Proceed to the System option.
DigitalFlow™ XGS868i Programming Manual
93
Appendix C. Programming the XGS868i Using PanaView™
C.5.2 Entering Data in the Channel System Option
1.
2.
From the Channel PROGRAM menu, highlight and double-click on the System option in the center pane.
The first prompt asks for the Channel (Site) Label. Enter the desired label (in any numeric or text combination up
to five characters) in the right pane, and click [Next Item].
3. Enter the desired Channel Message, and click [Next Item].
4. Double-click on the desired Volumetric Units (from the list shown in Table 17).
Note: Refer to the System option of the Global menu to choose between English or metric measurements.
Table 17: Available Volumetric/Totalizer Units
English
Metric
Actual Cubic Feet
Actual Cubic Meters
Thousands of ACF
Thousands of ACM
Millions of ACF
Millions of ACM
Standard Cubic Feet
Standard Cubic Meters
Thousands of SCF
Thousands of SCM
Millions of SCF
Millions of SCM
5.
6.
Double-click on the desired unit of Volumetric Time (from seconds to days) in the volumetric flow display.
Double-click on the desired number of Decimal Digits (digits to the right of the decimal point) in the volumetric
flow display.
7. Double-click on the desired Totalizer Units for the totalized flow rate display (listed in Table 17).
8. Double-click on the desired number of Decimal Digits (digits to the right of the decimal point) in the totalized flow
rate display.
The program now varies, depending on whether you have activated Mass Flow (see Chapter 1 for details).
•
If you have activated Mass Flow, continue to step 1 on the next page.
•
If you are not using Mass Flow, PanaView returns to the Channel PROGRAM window shown in Figure 41 on page 91.
Proceed to the Pipe option.
94
DigitalFlow™ XGS868i Programming Manual
Appendix C. Programming the XGS868i Using PanaView™
C.5.2a
1.
Programming the Mass Flow Option
Double-click on the desired Mass Flow units for flow rate display (listed in Table 18).
Table 18: Available Mass Flow Units
English
Metric
Pounds
Kilograms
KiloPounds = Thousands of
Pounds
Tonnes = Metric Tons (1000 KG)
MillionPounds
TONS (2000 LB)
2.
3.
Double-click on the desired Mass Flow Time units.
Double-click on the desired number of MDOT Decimal Digits (digits to the right of the decimal point) in the mass
flow rate display.
4. Double-click on the desired Mass Totalizer units for the totalized mass flow rate display (listed in Table 18).
5. Double-click on the desired number of Mass Decimal Digits (digits to the right of the decimal point) in the totalized mass flow rate display.
PanaView returns to the Channel PROGRAM window shown in Figure 41 on page 91. Proceed to the Pipe option on the
next page.
DigitalFlow™ XGS868i Programming Manual
95
Appendix C. Programming the XGS868i Using PanaView™
C.5.3 Entering Pipe Parameters
Enter the transducer and pipe parameters via the Pipe submenu. While following the programming instructions, refer
to Figure 55 on page 129 of Appendix D, PanaView Menu Maps.
1.
2.
From the Channel PROGRAM menu, highlight and double-click on the Pipe Parameters option in the center pane.
The first prompt asks for the Transducer Number.
•
For a standard transducer, double-click on the Standard option in the center pane. Then enter the number
engraved on the transducer head in the right pane, and click [Next Item].
•
If there is no number engraved on the transducer head, double-click on the Special option, enter an
assigned number (from 91 to 99), and click [Next Item].
IMPORTANT:
Special transducers, which have no engraved number on the head, are rarely used. Examine the
transducer head carefully for a number.
The menu now varies, depending on your selection in step 2.
•
If you entered the number for a standard transducer, proceed to the Pipe OD prompt in step 4.
•
If you entered the number for a special transducer, proceed to step 3 below.
C.5.3a
Special Transducers
3. For special transducers:
Note: Panametrics Measurement & Control will supply the information required for steps a and b with the
transducers.
a. Double-click on the appropriate Frequency (from 25 kHz to 500 kHz).The frequency is required to transmit an
excitation voltage at the transducer’s natural frequency.
b. Enter the Time Delay (Tw) value supplied by Panametrics Measurement & Control and click [Next Item].
Tw is the time required for the transducer signal to travel through the transducer and its cable. This time delay must
be subtracted from the transit times of the upstream and downstream transducers to ensure an accurate
measurement.
96
DigitalFlow™ XGS868i Programming Manual
Appendix C. Programming the XGS868i Using PanaView™
C.5.3b
4.
Pipe OD
Click on the appropriate Pipe OD Unit type in the center pane from the list shown in Table 19. Then enter the
known pipe outside diameter or circumference in the right pane and click [Next Item].
Obtain the required information by measuring either the pipe outside diameter (OD) or circumference at the
transducer installation site. The data may also be obtained from standard pipe size tables found in Sound Speeds
and Pipe Size Data (914-004).
English
Table 19: Available Pipe OD Units
Metric
inches
mm
feet
meters
circum.in. = pipe circumference in inches
circum.mm = pipe circumference in millimeters
circum.ft = pipe circumference in feet
circum.m = pipe circumference in meters
5. Enter the known Pipe Wall Thickness (in inches or mm) in the right pane and click [Next Item].
C.5.3c
6.
Path and Axial Lengths
Click on the appropriate Path Length unit type in the center pane. Then enter the path length of the ultrasonic
signal in the right pane and click [Next Item].
Note: If a spoolpiece was ordered with the meter, the transducer signal path length (P) and the transducer signal
axial length (L) are engraved on the flowcell and/or are included in the documentation supplied with the
meter. For on-site transducer installations, refer to Appendix C, Measuring P and L Dimensions, in the Startup
Guide for instructions.
7. Click on the appropriate Axial Length unit type in the center pane. Then enter the axial length of the ultrasonic
signal in the right pane and click [Next Item].
C.5.3d
Fluid Type
C.5.3e
Reynolds Correction
8.
9.
Double-click on the appropriate Fluid Type, either Steam or Other.
•
If you select Other, PanaView asks for the Fluid Soundspeed. Enter the appropriate soundspeed (in ft/sec)
and click [Next Item].
Double-click on the appropriate choice to indicate whether you want Reynolds Correction.
•
If Off is selected, enter the Calibration Factor and click on [Next Item].
•
If On is selected, enter the Kinematic Viscosity and click [Next Item]. Then enter the Calibration Factor and click
[Next Item].
PanaView returns to the Channel PROGRAM menu. You have completed entering pipe parameters.
DigitalFlow™ XGS868i Programming Manual
97
Appendix C. Programming the XGS868i Using PanaView™
C.5.4 Entering Input/Output Parameters
Enter the zero cutoff value and set up the temperature, pressure and quality inputs via the Input/Output submenu.
While programming these parameters, refer to Figure 55 on page 129 of Appendix D, PanaView Menu Maps.
IMPORTANT:
C.5.4a
If an option card in Slot 1 fails to appear in this menu, it may be turned OFF. See the
Global-I/O-Options section on page 106 for setup instructions.
Zero Cutoff Value
Near a zero flow rate, the Model XGS868i’s readings may fluctuate due to small offsets caused by thermal drift or
similar factors. To force a zero display reading when there is minimal flow, enter a zero cutoff value as described in
the following steps:
1.
2.
From the Channel menu, highlight and double-click on the Input/Output option in the center pane.
The program asks for the Zero Cutoff. Enter a value from 0 to 1 ft/sec (0 to 0.30 m/sec) for the zero cutoff and click
[Next Item]. The recommended setting is 0.1 ft/sec (0.03 m/sec).
C.5.4b
Assume Saturation
This prompt permits you to use a single input for either temperature or pressure to measure mass flow. The User
Program contains a table that correlates pressure and temperature for saturated steam. If the meter can assume
the steam is always at or near saturation, then only a temperature or pressure input is needed. The meter will
interpolate the corresponding pressure or temperature.
1.
At the Assume Saturation? prompt, scroll to No or Yes and click [Next Item].
•
If you selected Yes, proceed to Step 2 below.
•
C.5.4c
1.
Steam Input Type
Scroll to the Steam Input Type that will be used to measure mass flow and click [Next Item].
•
If you selected Temperature, proceed to Temperature Input on page 99.
•
Note:
98
If you selected No, proceed to Step 1 on the next page.
If you selected Pressure, proceed to Base Temperature on page 99.
Panametrics Measurement & Control recommends using a live input for either temperature or pressure
when assuming the saturation.
DigitalFlow™ XGS868i Programming Manual
Appendix C. Programming the XGS868i Using PanaView™
C.5.4d
Temperature Input
The XGS868i can use either a fixed temperature value or a live temperature input to calculate the density for the mass
flow rate display.
1.
Double-click on a Fixed temperature value or to set up the option card in Slot 1 that will supply the live temperature input and click [Next Item].
Note: If Slot 1 contains an activated option card with an analog input assigned to Temperature or an RTD input,
Slot 1 appears as an option at the above prompt. If the process temperature is stable, a fixed value may be
used, but most applications require a live temperature input. If there is no active option card for
temperature, the meter assumes you are using a fixed temperature.
2.
Proceed to one of the following sections:
•
If you selected Fixed - proceed to Step 3.
•
If you selected Slot 1 - proceed to Step 4.
3.
Enter the known Fixed Temp. (process temperature) and click [Next Item]. The meter will accept values from
–328° to 1,832°F (–200° to 1,000°C). Proceed to Base Temperature below.
4. Select Input A or Input B and click [Next Item]. The inputs were labeled during setup.
Note: The set up of Input A is used as an example. Identical procedures would be used to set up Input B.
C.5.4e
1.
2.
Base Temperature
Enter the Base Temperature and click [Next Item]. The ratio of this value to the actual temperature is used to calculate the standard mass flow rate.
Do one of the following:
•
If you selected Pressure as the Input Type, proceed to Pressure Input on the next page.
•
C.5.4f
If you selected Temperature as the Input Type, proceed to Base Pressure on the next page.
Pressure Input
1. Double-click on a Fixed pressure value or to set up the option card in Slot 1 that will supply the live pressure input.
Note: If Slot 1 contains an activated option card with an input assigned to Pressure, Slot 1 appears as an option at
the above prompt. If the process pressure is stable, a fixed value may be used, but most applications
require a live pressure input. If there is no active option card for pressure, the meter assumes you are using
a fixed pressure.
2.
Proceed to one of the following steps:
•
If you selected Fixed - proceed to Step 3.
•
3.
4.
If you selected Slot 1 - proceed to Step 4.
Enter the known Fixed process Pressure and click [Next Item]. The meter will only accept values from 0 to 5,000
psia. Proceed to Base Pressure below.
Double-click on Input A or Input B. The inputs were labeled during setup.
Note:
The set up of Input A is used as an example. Identical procedures would be used to set up Input B.
C.5.4g
Base Pressure
C.5.4h
Low Pressure Switch
1.
1.
Enter the Base Pressure and click [Next Item]. The ratio of this value to the actual pressure is used to calculate the
standard mass flow rate.
Click on Yes or No to activate or deactivate the Low Pressure Switch software function and click [Next Item].
•
If you selected Yes, enter the Pressure Limit, the low pressure switch set point, and click [Next Item]. The
acceptable range is 0 to 5,000 psia. The meter will stop taking readings if the pressure drops below this value.
•
If you selected No, go to Quality Input on page 100.
DigitalFlow™ XGS868i Programming Manual
99
Appendix C. Programming the XGS868i Using PanaView™
C.5.4i
Quality Input
When the temperature and pressure inputs indicate that the steam is saturated, the Quality Input value is used for
the mass flow rate calculations. Unless a different value is accurately known, accept the default value at the
following prompt:
Note:
The quality value indicates what fraction of the fluid is in the gas phase. The remaining fraction is assumed
to be liquid water. Thus, a quality value of 1.0 indicates 100% gas.
1.
At the Quality Input prompt, scroll to a fixed steam quality value or to set up the option card in Slot 1 that will supply the live steam quality input and click [Next Item].
Note: If Slot 1 contains an activated option card with an analog input that has been programmed as Special, Slot 1
appears as an option at the above prompt. Normally, a fixed value of 1.0 (100% steam) should be used for
the steam quality value.
If there is no active option card for a special input, the meter assumes you are using a fixed quality value.
•
If you selected Fixed, proceed to Step 3.
•
If you selected Slot 1, proceed to Step 4.
2. Enter the known Fixed steam Quality and click [Next Item]. (The meter will accept values from 0.0000 to 1.0000.)
3. Scroll to Input A or Input B and click [Next Item]. The inputs were labeled during setup.
Note: The set up of input A is used as an example. Identical procedures would be used to set up input B.
PanaView returns to the Channel PROGRAM menu. You have completed entering input/output parameters.
C.5.5 Entering Setup Parameters
The signal limits and response times for the Model XGS868i are specified via the SETUP submenu. While following the
programming instructions, refer to Figure 56 on page 130 of Appendix D, PanaView Menu Maps. This submenu
includes four options:
•
Signal - set the parameters related to the transducer signal
•
Default Setup - initialize all parameters to default values
•
V Averaging - specify the response of the meter to step changes
•
Advanced Features - enable mass flow or activate K factors.
To enter the Set Up submenu, highlight and double-click on the Set Up option in the center pane of the Channel
menu. Remember to record all programmed data in Appendix B, Data Records.
C.5.5a
The Signal Option
Use this option to set the limits for the incoming signal and other parameters affecting the transducer signal. For
example, the programmed signal strength low limit may be used to determine the trigger point for an alarm.
CAUTION!
1.
2.
100
The Signal default settings are suitable for most applications. Consult the factory
before changing any of these parameters.
From the Set Up option menu, highlight and double-click on Signal in the center pane.
For each parameter, click [Next Item] to accept the current value or enter a new value and click [Next Item].
Table 20 on page 101 lists ranges and default parameters for each parameter.
DigitalFlow™ XGS868i Programming Manual
Appendix C. Programming the XGS868i Using PanaView™
Transducer
Signal
Parameters
Table 20: Transducer Signal Settings
Range
Default
Value
Signal Low
Limit
20 to 100
20
The E1:LOW SIGNAL error message appears when the signal
strength falls below the programmed SIGNAL LOW LIMIT value. See
Chapter 2 in the Service Manual for a discussion of error codes.
Correlation
Peak Limit
0 to 500
100
The E4: SIGNAL QUALITY error message appears when the signal
quality falls below the programmed COR. PEAK LIMIT value. See
Chapter 2 in the Service Manual for a discussion of error codes
20%
The E2:SOUNDSPEED error message appears when the calculated
fluid sound speed differs from the fluid sound speed entered in the
Channelx-System menu by more than the programmed
SOUNDSPEED
± LIMIT value. See Chapter 2 in the Service Manual for a
discussion of error codes.
Soundspeed
+/– Limit
Velocity
Low Limit
Velocity
High Limit
Acceleration
Limit
Amplitude
Discriminator
Low
Amplitude
Discriminator
High
Delta T Offset
Skan T Offset
% of Peak
1 to 50%
–500 to
500 ft/sec
(–150 to
150 m/sec)
Description
–150 ft/sec
(–46 m/sec)
The E3: VELOCITY RANGE error messages appears when the
calculated fluid velocity is less than the programmed VELOCITY
LOW LIMIT value. See Chapter 2 in the Service Manual for a
discussion of error codes.
150 ft/sec
(46 m/sec)
The E3: VELOCITY RANGE error messages appears when the
calculated fluid velocity exceeds the programmed VELOCITY HIGH
LIMIT value. See Chapter 2 in the Service Manual for a
discussion of error codes.
15 ft/s
(5 m/s)
The E6: CYCLE SKIP error message appears when the calculated
fluid velocity changes by more than the programmed
ACCELERATION LIMIT value from one reading to the next. See
Chapter 2 in the Service Manual for a discussion of error codes.
–500 to
500 ft/sec
(–150 to
150 m/sec)
0 to 250 ft/s
(0 to 76 m/s)
0 to 100
0 to 100
-1000 to 1000
µsec
–500 to
500 µsec
1 to 100%
DigitalFlow™ XGS868i Programming Manual
14
34
0 µsec
58 µsec
50%
The amplitude discriminator measures the transducer signal
received by the Model XGS868i. The default value for the above
parameter is 14, and values from 0 to 100 are acceptable. The E5:
AMPLITUDE error
message appears when the amplitude discriminator falls below
the
programmed AMP. DISCRIM LOW value. See Chapter 2 in the
Service Manual for a discussion of error codes.
The amplitude discriminator measures the transducer signal
received by the Model XGS868i. The default value for the above
parameter is 34, and values from 0 to 100 are acceptable. The E5:
AMPLITUDE error
message appears when the amplitude discriminator exceeds the
programmed AMP. DISCRIM HIGH value. See Chapter 2 in the
Service Manual for a discussion of error codes.
An offset between the upstream and downstream transit times is
specified at this prompt.
At this prompt, specify a time measurement offset that
compensates for any shift resulting from cross-correlation. Set to 0
for active Skan T
Offset.
The percentage of peak used to calculate the transit times and
Delta T is specified at this prompt.
101
Appendix C. Programming the XGS868i Using PanaView™
Transducer
Signal
Parameters
M>S Switch
# Shifts
A Divisor
# Transmit
Pulses
T Window
(cycles)
R Window
(cycles)
Table 20: Transducer Signal Settings (cont.)
Default
Value
Range
0 to 250 µsec
50 µsec
0 to 10
0.1 to 10
3
2.5
Description
If the burst mode is set to Skan/Measure (S/M), the meter switches
from Skan to Measure Mode when Delta T is less than the
M>S_Switch value. DO NOT change this value unless advised to do
so by the factory.
The number of shifts corresponds to the actual number of
transmits per cycle (number of signals added together in one
direction to produce an averaged signal for one interrogation of
the fluid) and need only be changed if the environment is very
noisy or the acoustic signal is weak.
A Divisor is used to calculate the Measure Mode integrated
threshold level and is not normally changed.
# Transmit Pulses specifies the number of pulses in a burst. For
difficult conditions (i.e. long paths, high velocity or high
temperature), settings as high as 16 may be necessary.
1 to 16
4
0 to 1000
0
The XGS868i calculates the size of the transmit window based on
pipe size and fluid sound speed. However, for diagnostic purposes,
the
window size may be reset.
10
The XGS868i calculates the size of the receive window based on
pipe size and fluid soundspeed. However, for diagnostic purposes,
the
window size may be reset.
10 to 128
After responding to the above prompt, the meter returns to the SET UP option window.
C.5.5b
The Default Setup Option
Use this option to initialize (reset) all of the parameters within the Set Up Signal menu back to their default values.
Complete the following steps to reset all of the parameters:
1. From the Set Up option menu, highlight and double-click on Default Setup in the center pane.
2. Double-click on No to keep the current values or on Yes to reset all values to their default settings.
After responding to the above prompt, the meter returns to the Set Up option window.
C.5.5c
The V Averaging Option
Use this option to specify the number of readings that occur before the meter will respond to a step change in flow
rate. In general, the smaller the number of readings, the less steady the display will appear. Complete the following
steps to set the response time:
1. From the Set Up option menu, highlight and double-click on V Averaging in the center pane.
2. Double-click on the desired Response Time (from 1 to 60 sec).
For best results, select the STATS (statistics) option, as this increases the response time under steady flow conditions
while still allowing a rapid response to changes in flow rate.
After responding to the above prompt, the meter returns to the Set Up option window.
C.5.5d
The Advanced Features Option
This option enables you to enable the more advanced features of the meter. In this option you can do the following:
102
•
enter a table of K-factors (based on velocity or reynolds number) that compensates for non-linear flow rates
•
enable mass flow (calculated for static fluid density)
DigitalFlow™ XGS868i Programming Manual
Appendix C. Programming the XGS868i Using PanaView™
The Multiple K Factors Option
Use this option to enter a table of K-factors. K-factors are used to create a curve for the flow range (based on velocity
or reynolds number) that compensates for non-linear flow rates. The meter accepts from 2 to 20 pairs. Complete the
following steps to enter multiple K factors for velocity or reynolds values:
1. From the Advanced Features option menu, highlight and double-click on Multiple K Factors in the center pane.
2. Double-click on Yes to Activate Multi K Factors or on No to disable this option.
If NO was selected, the meter returns to the Advanced Features window. If YES was selected, proceed to Step 3.
3.
Double-click on the desired Custom Type (velocity or reynolds).
•
If you selected CstR (Reynolds), enter the desired Kinematic Viscosity, and click [Next Item].
4.
Double-click on Yes to Edit the K-factor Table or on No to retain the current K-factor table (and return to the
Advanced Features window).
Note: If the necessary velocity/reynolds vs. K-factor data was not provided with the Model XGS868i’s
documentation, the K-factor table cannot be edited.
If NO was selected, the meter returns to the Advanced Features window. If YES was selected, proceed to Step 5.
5. Enter the Number Of K-factors (from 2 to 20) to be entered into the table, and click [Next Item].
Note: When editing the K-factor table, the velocities must be entered in increasing order.
6. Enter the Velocity/Reynolds Value for K-factor number “X” and click [Next Item].
7. Enter the K-factor corresponding to velocity/reynolds number “X” (0.333 to 3.0) and click [Next Item].
The Velocity # and K Factor # prompts repeat for each pair. After entering all the pairs, the meter returns to the
Advanced Features window.
The Mass Flow Option
Use this option to calculate mass flow from a static fluid density. Complete the following steps to enter the static
density of the fluid:
1.
2.
3.
From the Advanced Features option menu, highlight and double-click on Mass flow calculation in the center
pane.
Double-click on Yes to activate Static Density or on No to disable this option. (If you select No, PanaView returns
to the Advanced Features window.)
If you select Yes, enter the Fluid Density (0.00001 to 0.100 lb/ft3 or 0.00001 to 123.18 kg/m3) and click [Next Item].
PanaView returns to the Advanced Features window.
After responding to the above prompt, the meter returns to the Advanced Features window. Click [Exit Page] three
times to return to the Site Edit Menu.
C.6
Entering Data in the Global Menu
The Global menu is used to enter information that is not specific to any of the individual channels. Information
programmed via this menu is used to enter several general system parameters (e.g., English or metric units). For
meters with 2 channels, this menu is also used to compute parameters such as the sum, difference or average of the
channel 1 and channel 2 signals. When calculating the SUM, DIF or AVE readouts, data from the Global-System
submenu is used. Any conflicting data entered in the Channel-System submenu is overridden.
The following submenus are included in the Global menu:
•
System - use to specify the units of measure used in calculations
•
Input/Output - used to set up error handling and to configure analog inputs and outputs
•
Comm port - used to set up the serial communications port and MODBUS parameters
To enter the Global menu, double-click on the Global entry in the left pane of the Site Edit Menu window. Then proceed
to the appropriate section of this chapter for instructions. Refer to Figure 57 on page 131 in Appendix D, PanaView
Menu Maps, and remember to record all programming data in Appendix B, Data Records.
DigitalFlow™ XGS868i Programming Manual
103
Appendix C. Programming the XGS868i Using PanaView™
C.6.1 Entering Global-System Data
While completing these instructions, see the menu map in Figure 57 on page 131 in Appendix D, PanaView Menu Maps.
1.
2.
In the Site Data Menu, double-click on the Global entry.
Highlight and double-click on the System option in the center pane. The window now appears similar to
Figure 45.
Figure 45: The System Option in the Global Menu
3.
4.
Double-click on the desired System Units selection (either metric or English). The XGS868i will display all parameters and measurements in the designated units.
Double-click on the desired Pressure Units (absolute or gauge) and click [Next Item].
a. If gauge was selected, enter the desired Atmospheric Pressure, and click [Next Item].
5.
•
Do one of the following:
For a single-channel XGS868i, the program returns to the Global PROGRAM menu. Click [Exit Page].
•
For a 2-channel meter, proceed to step 6 on the next page.
104
DigitalFlow™ XGS868i Programming Manual
Appendix C. Programming the XGS868i Using PanaView™
C.6.1a
1.
Volumetric Units
Double-click on the desired Volumetric Units for the flow rate display. Table 21 lists the available units.
Table 21: Available Volumetric/Totalizer Units
English
Metric
2.
Actual Cubic Feet
Actual Cubic Meters
Thousands of ACF
Thousands of ACM
Millions of ACF
Millions of ACM
Standard Cubic Feet
Standard Cubic Meters
Thousands of SCF
Thousands of SCM
Millions of SCF
Millions of SCM
Double-click on the desired Time units for the flow rate display.
3. Double-click on the desired number of Vol Decimal Digits (digits to the right of the decimal point in the
volumetric flow rate display).
C.6.1b
1.
2.
3.
Selecting Totalizer Units
Double-click on the desired Totalizer Units for the totalized flow rate display. Available units are listed in Table C-5
above.
Double-click on the desired number of Tot Decimal Digits (digits to the right of the decimal point in the totalized
flow rate display).
Do one of the following:
•
If Mass Flow is ON, proceed to Selecting the Mass Flow Units below.
•
If Mass Flow is OFF, the meter returns to the Global PROGRAM window. Click [Exit Page] to return to the Site Edit
Menu.
Note:
To activate mass flow, refer to page 103. The following prompts will only appear if mass flow is activated for
both channels.
DigitalFlow™ XGS868i Programming Manual
105
Appendix C. Programming the XGS868i Using PanaView™
C.6.1c
1.
Selecting Mass Flow Units
Double-click on the desired Mass Flow units for flow rate display (listed in Table 22).
Table 22: Available Mass Flow Units
English
Metric
Pounds
Kilograms
KiloPounds
(Thousands of Pounds)
Tonne = Metric Tons (1000 KG)
MillionPounds
TONS (2000 LB)
2.
3.
Double-click on the desired Mass Flow Time units (from seconds to days).
Double-click on the desired number of MDOT Dec. Digits (digits to the right of the decimal point) in the mass flow
rate display.
4. Double-click on the desired Mass Totalizer (units for the totalized mass flow rate display, listed in Table 22).
5. Double-click on the desired number of Mass Decimal Digits (digits to the right of the decimal point) in the totalized mass flow rate display.
The XGS868i returns to the Global PROGRAM window. Click [Exit Page] to return to the Site Edit Menu.
You have completed entering selections in this option.The program returns to the Global PROGRAM menu.
C.6.2 Setting Up Inputs and Outputs
Set up the XGS868i’s inputs and outputs via the I/O submenu. While following the programming instructions, refer to
Figure 58 on page 132 in Appendix D, PanaView Menu Maps. Remember to record all programmed data in Appendix
B, Data Records.The I/O submenu consists of the following options:
•
Error Handling - program the meter’s response during an error condition
•
Options - set up any option cards and the Slot 0 analog outputs
•
Display - set up the LCD display.
To enter the I/O submenu:
1. In the Site Data Menu, double-click on the Global entry.
2. Highlight and double-click on the Input/Output option in the center pane.
Note: In this section, Slot 1 appears as an option only if a suitable option card is installed in Slot 1.
106
DigitalFlow™ XGS868i Programming Manual
Appendix C. Programming the XGS868i Using PanaView™
C.6.2a
Setting Up Error Handling
This menu option lets you set how the XGS868i will handle the outputs for measurements and average (two-path)
measurements during an error condition. See Chapter 2, Error Codes, in the Service Manual for a discussion of the
built-in error codes.
1.
2.
From the Input/Output option, highlight and double-click on the Error Handling option in the center pane.
Double-click on the desired Error Handling selection (as shown in Table 23 and Table 24).
a. If you selected Error Level in mA, enter the 4-20 mA Error Level (the number of milliamps the analog output
will put out during a fault condition). Enter a whole number between 0 and 22, and click [Next Item].
See Table 23 and Table 24 for a description of the error handling options available and how the totalizers and display
respond to them for a single and two-channel meter.
Option
Table 23: Error Options & Responses for Single-Channel Meter
Output Response
Totalizer Response
Hold Last
Value
Holds the last “good” reading
Holds the last “good” reading and continues to
totalize, based on that reading
Force Low
Forces the outputs to the low set point
Stops totalizing
Force High
Forces the outputs to the high set point
Stops totalizing
Force High
High
Forces the outputs 10% above the high set point
Stops totalizing
Error Level
in mA
Allows user to enter 4-20 mA error level in mA.
Sends analog outputs to entered mA level
when a fault occurs.
When
Measuring
Table 24: Error Options and Responses for a 2-Channel Meter
Totalizer Response When Error Handling is
Display Response
HOLD
LOW, HIGH, HHIGH
CH1 or CH2
(vel, vol, etc.)
Holds last “good” reading.
Holds last “good” reading and
continues to totalize based on that
“good” reading.
Stops totalizing.
SUM
Adds two channels using the
last “good” reading.
Holds last “good” reading and
continues to totalize based on two
channels.
Stops totalizing if either or
both channels go into
error.
DIF
Subtracts two channels using
the last “good” reading.
Holds last “good” reading and
continues to totalize based on two
channels.
Stops totalizing if either or
both channels go into
error.
AVE
See Error Handling for Average Measurements below.
For a one-channel meter, after responding to the above prompt, the meter returns to the Global I/O prompt shown
on page 106. For a two-channel meter, proceed to step 3 on page 108.
DigitalFlow™ XGS868i Programming Manual
107
Appendix C. Programming the XGS868i Using PanaView™
Error Handling for Average Measurements - AVE
The 2PATH ERROR HANDLING option is intended for applications where two sets of transducers are installed in the
same location in the same pipe to improve accuracy and the meter is operated in AVE mode. With this function
enabled, the Model XGS868i performs error handling only if both channels are in error. If this function is disabled, error
handling occurs when either channel goes into error.
3. Double-click Yes to enable Two-path Error Handling, or on No to disable this function.
Specific responses of the display and the totalizer to the two-path error handling option available at the above
prompt are listed in Table 25.
Table 25: 2-Path Error Response Options
Display Response
Option
NO
YES
Totalizer Response
Displays the average of CH1 and CH2, regardless
of the error state of either channel.
Outputs the average of CH1 and CH2 totals,
regardless of the error state of either channel.
1.
1. If one channel is in error, totalizing continues.
2. If both channels are in error, totalizing stops.
If one channel is in error, the other channel’s
value is displayed as the average.
2. If both channels are in error, the last average
reading is held.
After responding to the above prompt, the meter returns to the Input/Output option menu.
C.6.2b
Setting Up Option Cards
The Model XGS868i has two built-in analog outputs, which are assigned to Slot 0. Also, a variety of input/output
option cards may be installed in Slot 1. See Chapter 1, Installation, of the Startup Guide for a complete description of
the available option cards.
To access this submenu, double-click on the Options entry in the Input/Output submenu. This menu option is used to
set up and/or scale the inputs and outputs. To accomplish this, complete the following steps:
•
Double-click on the desired I/O Slot to program the I/O functions in that slot.
Note:
If an option card is not installed in Slot 1, the Slot1 option does not appear at the above prompt.
Proceed to the appropriate section for programming instructions specific to the type of input or output selected
above.
Analog Outputs
Complete the following steps to set up the analog outputs for any slot (refer to Figure 58 on page 132):
1. Double-click on the desired Output (A or B).
Note: The set up of output A is used here as an example. Identical procedures would be used to set up output B.
2.
Double-click on Off to disable Output A and return to step 1, or on 0-20 mA or 4-20 mA to specify the desired
range for output A.
Note: For a 1-Channel meter, proceed to step 4.
3.
108
Double-click on the desired Channel option. See Table 26 for a description of the channel options available.
Table 26: Channel Options
Option
Description
Channel 1
Channel 1
Channel 2
Channel 2
Add Channels
CH1+CH2
Subtract Channels
CH1-CH2
Average Channels
(CH1+CH2)/2
DigitalFlow™ XGS868i Programming Manual
Appendix C. Programming the XGS868i Using PanaView™
4.
Double-click on the desired Measurement Name. (Table 27 on page 109 provides a description of the available
parameters.)
Note:
All the options shown below will only appear if Mass Flow is activated.
Table 27: Available Measurement Parameters
Description
Option Bar
Good
Bad
Displays the flow velocity.
N.A.
N.A.
Volumetric
Displays the volumetric flow.
N.A.
N.A.
FWD Total
Displays the forward totalized volume flow.
N.A.
N.A.
REV Total
Displays the reverse totalized volume flow.
N.A.
N.A.
Time
Displays the total flow measurement time.
N.A.
N.A.
Mass Flow
Displays the mass flow.
N.A.
N.A.
FWD Mass
Displays the forward totalized mass flow.
N.A.
N.A.
REV Mass
Velocity
Displays the reverse totalized mass flow.
N.A.
N.A.
UP Sig Strength
Displays signal strength for upstream transducer.
50–75
<50 or >75
DN Sig Strength
Displays signal strength for downstream transducer.
50–75
<50 or >75
Displays measured speed of sound in the gas.
N.A.
N.A.
Soundspeed
UP Transit
Displays upstream ultrasonic signal transit time.
N.A.
N.A.
DN Transit
Displays downstream ultrasonic signal transit time.
N.A.
N.A.
N.A.
N.A.
N.A.
N.A.
0.3 - 3.0
N.A.
Displays transit time difference between the upstream and
downstream signals.
DeltaT
Reynolds #
Displays the Reynolds number.
K(Re)*MultiK
*KFactor
K factor, based on the Reynolds number.
Displays the percentage of peak (set to +50 by default).
N.A.
N.A.
UP Signal Q
PEAK%
Displays signal quality for upstream transducer.
>|800|
<|800|
DN Signal Q
Displays signal quality for downstream transducer.
>|800|
<|800|
24 ± 5
<19 or >29
24 ± 5
<19 or >29
UP Amp Discrim
DN Amp Discrim
Displays the value for the signal amplitude of the upstream
transducer.
Displays the value for the signal amplitude of the downstream
transducer.
UP+-Peak
Displays signal peaks for upstream transducer.
100-2300
<100 or >2300
DN+-Peak
Displays signal peaks for downstream transducer.
100-2300
<100 or >2300
UP DAC COUNTS
Displays AGC DAC count for upstream gain setting.
N.A.
N.A.
DN DAC COUNTS
Displays the AGC DAC count for the downstream gain setting.
N.A.
N.A.
Temperature
Displays gas temperature (from 0/4-20 mA input)
N.A.
N.A.
Pressure
Displays the gas pressure (from 0/4-20 mA input).
N.A.
N.A.
Compress
Displays the compressibility factor.
0–1
<0 or >1
Displays actual volumetric flow.
N.A.
N.A.
Displays standard volumetric flow.
N.A.
N.A.
UP Transit S
Displays Skan transit time upstream.
N.A.
N.A.
DN Transit S2
Displays Skan transit time downstream.
N.A.
N.A.
Displays Skan Delta T.
N.A.
N.A.
Displays Measure transit time upstream.
N.A.
N.A.
Act Vol.
Std Vol.
2
DeltaT S2
UP Transit M2
DigitalFlow™ XGS868i Programming Manual
109
Appendix C. Programming the XGS868i Using PanaView™
Option Bar
Table 27: Available Measurement Parameters
Description
Good
Bad
Displays Measure transit time downstream.
N.A.
N.A.
Displays Measure Delta T.
N.A.
N.A.
Displays the instantaneous velocity.
N.A.
N.A.
Displays saturation temperature for steam at current pressure.
N.A.
N.A.
Displays actual temperature minus the saturation temperature
(Tactual – Tsat).
0
<0
Fluid Dens
Displays fluid density.
N.A.
N.A.
T Kelvin
Displays the current process temperature in °K.
N.A.
N.A.
Displays the current process pressure in kPa
N.A.
N.A.
0.0 – 1.0
<0.0 or >1.0
DN Transit M2
DeltaT M2
Vinst
T Saturat
T Superht
kiloPascals
Steam Quality
Displays the steam quality from a live input or a static
programmed value.
1 available only if Multi K-factors = ON
2 available only if Burst Mode = S/M
Note:
The measurement units that appear in these prompts are those selected in the Global-System menu earlier
in this section.
5. Enter a flow rate value for the Zero (low) end of the analog output range and click [Next Item].
6. Enter a flow rate value for the Full (high) end of the analog output range and click [Next Item].
After responding to the above prompt, the meter returns to step 1. Click [Exit Page] to proceed to another menu or
option.
110
DigitalFlow™ XGS868i Programming Manual
Appendix C. Programming the XGS868i Using PanaView™
Option Card Analog Inputs
Complete the following steps to set up the analog inputs of an option card installed in Slot 1 (refer to Figure 58 on
page 132):
1. Double-click on the desired Input (A, B, C or D).
Note: The setup of input A is used as an example. Identical procedures would be used to set up the remaining
inputs.
2.
3.
•
Enter a Label of up to eight characters for input A and click on [Next Item].
Double-click on Off to disable Input A and return to step 1, or on Temp or Spec to designate it as a temperature or
special input.
OFF
If OFF was selected to disable input A, the meter returns to the Input prompt in step 1. Double-click on another input, or
click [Exit Page] to move to another menu.
•
TEMP or PRESR
If TEMP or PRESR was selected to set up input A as a live temperature or pressure input, complete steps 4 and 5 below:
4. Enter a value for the Base (low) end of the analog input range and click [Next Item].
5. Enter a value for the Full Scale (high) end of the analog input range and click [Next Item].
After responding to the above prompt, the meter returns to step 1. Click [Exit Page] to proceed to another menu or
option.
•
SPEC
If SPEC was selected to set up input A as a live special input, complete steps 6 through 10 below:
6.
7.
8.
9.
Enter a Name for input A and click [Next Item].
Enter the Units of measurement for input A and click [Next Item].
Enter a temperature value for the Base (low) end of the analog input range and click [Next Item].
Enter a temperature value for the Full Scale (high) end of the analog input range and click [Next Item].
10. After responding to the above prompt, the meter returns to step 1. Click [Exit Page] to proceed to another menu or
option.
DigitalFlow™ XGS868i Programming Manual
111
Appendix C. Programming the XGS868i Using PanaView™
Option Card RTD Inputs
Option cards with RTD inputs have a temperature range of –148o to 660oF (–100° to 350°C). Complete the following
steps to set up the RTD inputs of an option card installed in Slot 1 (refer to Figure 58 on page 132):
1. Double-click on the desired Input (A, B, C or D).
Note: The setup of RTD input A is used here as an example. Identical procedures would be used to set up the
remaining RTD inputs.
2.
3.
Enter a Label of up to eight characters for input A and click [Next Item].
Double-click on Off to disable Input A and return to step 1, or on Temp to enable input A as a live temperature
input.
4. Enter a temperature value for the Zero (low) end of the analog input range and click [Next Item].
5. Enter a temperature value for the Full Scale (high) end of the analog input range and click [Next Item].
After responding to the above prompt, the meter returns to step 1. Click [Exit Page] to proceed to another menu or
option.
112
DigitalFlow™ XGS868i Programming Manual
Appendix C. Programming the XGS868i Using PanaView™
Option Card Alarm Relays
Complete the following steps to set up the alarm relays of an option card installed in Slot 1 (refer to Figure 58 on
page 132):
1. Double-click on the desired Output (A, B, C or D).
Note: The set up of alarm A is used here as an example. Identical procedures would be used to set up the
additional alarms.
2.
Double-click on Off to disable Output A and return to step 1, or on High, Low or Fault to select the desired alarm
type.
3. Double-click on No for standard alarm operation, or on Yes for Failsafe operation. (See Chapter 1, Installation, of
the Startup Guide for failsafe wiring instructions.)
For a 1-Channel meter, proceed to step 5.
4.
Double-click on the desired Channel option. See Table 28 for a description of the channel options available.
Table 28: Channel Options
Option
Description
Note:
Channel 1
Channel 1
Channel 2
Channel 2
Add Channels
CH1+CH2
Subtract Channels
CH1-CH2
Average Channels
(CH1+CH2)/2
If FAULT was selected as the alarm type, the next two prompts do not appear. You have completed entering
data in this option.
5.
Double-click on the desired Measurement Name. (Table 27 on page 109 provides a description of the available
parameters.)
Note: The measurement units that appear in these prompts are those selected in the Global-System menu earlier
in this section.
6. Enter a value for the Trigger Point of the alarm and click [Next Item].
7. Double-click on the type of Error (flow, non-flow or both) that will trigger the fault alarm and press [Enter].
After responding to the above prompt, the meter returns to step 1. Click [Exit Page] to proceed to another menu or
option.
DigitalFlow™ XGS868i Programming Manual
113
Appendix C. Programming the XGS868i Using PanaView™
Option Card Totalizer Outputs
This type of output issues one pulse per selected volume of flow. The meter produces a pulse each time the
programmed amount of flow passes through the pipe. Complete the following steps to set up the totalizer outputs of
an option card installed in Slot 1:
1. Double-click on the desired Output (A, B, C or D).
Note: The set up of output A is used as an example. Identical procedures would be used to set up the other
outputs.
2. Double-click on Off to disable Output A and return to step 1, or on Totalizer to set up output A as a totalizer output.
For a 1-Channel meter, skip to step 4.
3.
4.
Double-click on the desired Channel option.See Table 28 on page 113 for a description of the channel options
available at the above prompt.
Double-click on the desired Measurement Name, as listed in Table 29.
Table 29: Output Measurement Options
Forward Totalized Volume Flow
Reverse Totalized Volume Flow
Forward Totalized Mass Flow
Reverse Totalized Mass Flow
Note:
The measurement units that appear in these prompts are those selected in the Global-System menu earlier
in this section.
Enter a value between 50 sec and 500,000 sec for Pulse On Time (the frequency of the totalizer pulses) and
click [Next Item].
Note: A complete pulse consists of equal amounts of ON and OFF times. Choose a value that is compatible with
the counter to be used.
5.
6. Enter a value for the number of measurement units represented by each pulse, and click [Next Item].
After responding to the above prompt, the meter returns to step 1. Click [Exit Page] to proceed to another menu or
option.
114
DigitalFlow™ XGS868i Programming Manual
Appendix C. Programming the XGS868i Using PanaView™
Option Card Frequency Outputs
This type of output produces a frequency pulse that is proportional to the output measurement. Complete the
following steps to set up the frequency outputs of an option card installed in Slot 1 (see Figure 58 on page 132):
1. Double-click on the desired Output (A, B, C or D).
Note: The set up of output A is used as an example. Identical procedures would be used to set up the other
outputs.
2.
Double-click on Off to disable Output A and return to step 1, or on Frequency to set up output A as a frequency
output.
For a 1-Channel meter, skip to step 4.
3.
Double-click on the desired Channel option.See Table 28 on page 113 for a description of the channel options
available at the above prompt.
4. Double-click on the desired Measurement Name. (Table 27 on page 109 provides a description of the available
parameters.)
Note: The measurement units that appear in these prompts are those selected in the Global-System menu earlier
in this section.
5. Enter a flow rate value for the Zero (low) end of the frequency output range and click [Next Item].
6. Enter a flow rate value for the Full (high) end of the frequency output range and click [Next Item].
7. Enter a value between 1 and 10,000 for the Full Scale Frequency and click [Next Item].
After responding to the above prompt, the meter returns to step 1. Click [Exit Page]:
•
once to return to the Global I/O option:
•
twice to return to the Global PROGRAM option:
•
three times to return to the Site Edit Menu:
•
four times to exit the Site Edit Menu.
DigitalFlow™ XGS868i Programming Manual
115
Appendix C. Programming the XGS868i Using PanaView™
C.6.2c
Programming the LCD
Through PanaView, you can program the LCD display to display up to four variables in sequence. Complete the
following steps to program the LCD display:
Note:
When you first initialize the XGS868i, the number of LCD parameters is set to OFF. You must program the LCD
to display any measured parameters.
1.
2.
From the Input/Output option, highlight and double-click on the Display option in the center pane.
The first prompt asks for the # of LCD Parameters. Double-click on the desired number (from LCD OFF through 1-4
and KEY).
The OFF setting switches the measurement display off, while the KEY setting enables users to change the
measurement display via the arrow keys, without accessing the Keypad Program. If you select KEY:
•
To view a parameter other than the one currently displayed, press the [] or [] keys to scroll through the
various parameters.
•
To scroll through the channel options on a two-channel XGS868i, press the [] or [] keys until you have
reached the desired option.
Note:
3.
For a 1-channel XGS868i, skip to step 4.
Scroll to the desired Channel option, as listed in Table 30.
Table 30: Channel Options
Option
Description
4.
5.
116
CH1
Channel 1
CH2
Channel 2
SUM
CH1+CH2
DIF
CH1-CH2
AVE
(CH1+CH2)/2
For each channel, select the desired Measurement Parameter, as shown in Table 27 on page 109.
Repeat steps 3 and 4 for each parameter. PanaView returns to the Global I/O menu.
DigitalFlow™ XGS868i Programming Manual
Appendix C. Programming the XGS868i Using PanaView™
C.6.3 Entering Communications Data
The Model XGS868i flowmeter is equipped with an RS232 or an RS485 serial interface. An RS485 option is also
available with MODBUS capability. When the MODBUS option is present, the XGS868i may also have the standard
RS232 serial interface.
The serial port is used to transmit stored data and displayed readings to a personal computer by connecting the
meter’s serial interface to the serial port of the PC. In addition, the Model XGS868i can receive and execute remote
commands, using PanaView software, via this link.
Use the Comm port submenu to set the communications port and MODBUS parameters. While following the
programming instructions, refer to Figure 57 on page 131 of Appendix D, PanaView Menu Maps.
Note:
C.6.3a
1.
For a more detailed explanation of the MODBUS interface, refer to Chapter 1, Setting Up MODBUS
Communications, on page 35.
Setting Up the Serial Port
To enter this submenu from the Global menu, highlight and double-click on the Comm port option in the center
pane.
2. Enter a Meter Address number between 1 and 254 and click [Next Item]. The default number is 1.
A meter address is only necessary for communication with the Panametrics Measurement & Control PanaView
software. See the PanaView User’s Manual for more information.
IMPORTANT:
If the meter address or baud rate is changed, communication with PanaView must be re-established
with the new address number.
3. Double-click on the desired Baud Rate (from 300 to 19,200).
If you have the RS485 MODBUS option, proceed to step 4 below. If you have the standard RS232 serial interface, the
meter exits the Comm port submenu and returns to the Global PROGRAM prompt.
Note:
The XGS868i MODBUS communication settings chosen in the next four steps must match those of the
MODBUS control system.
4. Double-click on the desired MODBUS Baud Rate (from 2400 to 19,200).
5. Double-click on the desired MODBUS Parity (None, Odd or Even).
6. Double-click on the desired MODBUS Stop Bits (1 or 2).
7. Enter the desired MODBUS Address.
The meter exits the Comm port submenu and returns to the Global window. Click [Exit Page] once to return to the Site
Edit Menu, and [Close] to exit the Site Edit Menu.
IMPORTANT:
You must reboot the XGS868i to load the new settings.
Refer to the section Requesting Parameters Using MODBUS on the following page to retrieve data from the XGS868i
using MODBUS.
DigitalFlow™ XGS868i Programming Manual
117
Appendix C. Programming the XGS868i Using PanaView™
C.6.3b
Requesting Parameters Using MODBUS
To request specific parameters from the XGS868i via the MODBUS, the control system must access the appropriate
register number, as shown in Table 31. Only registers 1–84 are available with the XGS868i for MODBUS
communications. Registers 508–512 are used by the XGS868i to store the MODBUS parameters.
:
Table 31: MODBUS Registers
Description
Units
Scaling
(decimal
places)
1
1Clear Totalizers
none
--
2 (16 bit signed)
2
CH1 Velocity
ft/s or m/s
2
4 (32 bit integer)
4
CH1 Volumetric
VOL_U
--
4 (IEEE 32 bit)
6
CH1 +Totals
TOT_U
Register 10
4 (32 bit integer)
8
CH1 -Totals
TOT_U
Register 10
4 (32 bit integer)
10
CH1 #T Digits
none
0
2 (16 bit integer)
11
CH1 Totalizer Time
sec
2
4 (32 bit integer)
13
2CH1 Error Value
none
0
2 (16 bit integer)
14
CH 1 SSUP
none
1
4 (32 bit integer)
MODBUS
Reg #
Size in Bytes
16
CH 1 SSDN
none
1
4 (32 bit integer)
18
CH 1 SNDSP
ft/s or m/s
0
4 (32 bit integer)
20
CH 2 Velocity
ft/s or m/s
2
4 (32 bit integer)
22
CH 2 Volumetric
VOL_U
--
4 (IEEE 32 bit)
24
CH 2 +Totals
TOT_U
Register 28
4 (32 bit integer)
26
CH 2 -Totals
TOT_U
Register 28
4 (32 bit integer)
28
CH2 # T Digits
none
0
2 (16 bit integer)
29
CH2 Totalizer Time
sec
2
4 (32 bit integer)
31
2
CH2 Error Value
none
0
2 (16 bit integer)
32
CH 2 SSUP
none
1
4 (32 bit integer)
34
CH 2 SSDN
none
1
4 (32 bit integer)
36
CH 2 SNDSP
ft/s or m/s
0
4 (32 bit integer)
38
3AVG Velocity
ft/s or m/s
2
4 (32 bit integer)
40
3AVG Volumetric
VOL_U
--
4 (IEEE 32 bit)
42
3AVG+Totals
TOT_U
Register 46
4 (32 bit integer)
Description
Units
Scaling
(decimal
places)
Size in Bytes
44
3AVG-Totals
TOT_U
Register 46
4 (32 bit integer)
46
AVG #T Digits
none
0
2 (16 bit integer)
47
3AVG Totalizer Time
sec
2
4 (32 bit integer)
49
4AVG Error Value
none
0
2 (16 bit integer)
MODBUS
Reg #
118
DPR Hex
Addr
DPR Hex
Addr
50
3
AVG SSUP
none
1
4 (32 bit integer)
52
3
AVG SSDN
none
1
4 (32 bit integer)
54
3AVG SNDSP
ft/s or m/s
0
4 (32 bit integer)
DigitalFlow™ XGS868i Programming Manual
Appendix C. Programming the XGS868i Using PanaView™
56
Table 31: MODBUS Registers
CH 1 Power
Power_u
58
CH 1 +Energy
60
62
63
--
4 (IEEE 32 bit)
Energy_u
Register 62
4 (32 bit integer)
CH 1 -Energy
Energy_u
Register 62
4 (32 bit integer)
CH 1 # Energy Digits
none
0
2 (16 bit integer)
CH 1 TempS
°F or °C
2
4 (32 bit integer)
65
CH 1 TempR
°F or °C
2
4 (32 bit integer)
67
CH 1 TS-TR
°F or °C
2
4 (32 bit integer)
69
CH 1 DELTH
Btu/lb or
J/gm
2
4 (32 bit integer)
71
CH 2 Power
Power_u
--
4 (IEEE 32 bit)
73
CH 2 +Energy
Energy_u
Register 77
4 (32 bit integer)
75
CH 2 -Energy
Energy_u
Register 77
4 (32 bit integer)
77
CH 2 # Energy Digits
none
0
2 (16 bit integer)
78
CH 2 TempS
°F or °C
2
4 (32 bit integer)
80
CH 2 TempR
°F or °C
2
4 (32 bit integer)
82
CH 2 TS-TR
°F or °C
2
4 (32 bit integer)
84
CH 2 DELTH
Btu/lb or
J/gm
2
4 (32 bit integer)
5MODBUS baud rate
none
0
2 (16 bit integer)
MODBUS parity
none
0
2 (16 bit integer)
508
3F6
509
3F8
510
3FA
7MODBUS stop bits
none
0
2 (16 bit integer)
511
3FC
MODBUS meter addr
none
0
2 (16 bit integer)
512
3FE
RESERVED
none
---
---
6
DigitalFlow™ XGS868i Programming Manual
119
Appendix C. Programming the XGS868i Using PanaView™
C.6.3b Requesting Parameters Using MODBUS (cont.)
Notes:
1.
2.
3.
4.
5.
6.
7.
8.
Clear Totalizers: flag from the 8051 to clear totalizers in the 68332 memory.
Error Value: see table in XGS868i manual for error codes
Average:
average of channel 1 and channel 2 if both channels out of error,
channel 1 value if channel 2 is in error,
channel 2 value if channel 1 is in error,
zero if both channels in error.
Average Error Status:
0 = both in error
1 = chan 2 in error,
2 = chan 1 in error,
3 = both ok
MODBUS baud rate:
5 = 2400, 6 = 4800, 7 = 9600
MODBUS parity:
0 = none, 1 = odd, 2 = even
MODBUS stop bits:
1 = 1 stop bit, 2 = 2 stop bits
General:
Registers are written if corresponding functions are actuated by the user. Registers for unactuated functions are
initialized to zero at startup.
Notes:
1.
2.
3.
4.
5.
6.
7.
8.
120
Clear Totalizers: flag from the 8051 to clear totalizers in the 68332 memory.
Error Value: see table in XMT868i manual for error codes
Average:
average of channel 1 and channel 2 if both channels out of error,
channel 1 value if channel 2 is in error,
channel 2 value if channel 1 is in error,
zero if both channels in error.
Average Error Status:
0 = both in error
1 = chan 2 in error,
2 = chan 1 in error,
3 = both ok
MODBUS baud rate:
5 = 2400, 6 = 4800, 7 = 9600
MODBUS parity:
0 = none, 1 = odd, 2 = even
MODBUS stop bits:
1 = 1 stop bit, 2 = 2 stop bits
General:
Registers are written if corresponding functions are actuated by the user. Registers for unactuated functions are
initialized to zero at startup.
DigitalFlow™ XGS868i Programming Manual
Appendix C. Programming the XGS868i Using PanaView™
C.6.3c
Activating Security in the Global Menu
In order to prevent unauthorized tampering with the flowmeter’s programming, the XGS868i is equipped with a
security feature that locks all the keys except [PROG] (which, when pressed, requires the password).
When the system is locked, access to the menus will be denied unless the correct password is entered. The XGS868i is
shipped with a default password (2719 and three spaces). For increased security, the default password should be
changed.
Note:
Once the system has been locked, it can only be unlocked by entering the password, because access to
the SECUR submenu is restricted.
While completing these instructions, refer to the menu map in Figure 57 on page 131.
1.
In the Site Data Menu, double-click on the Global entry. If the system is unlocked, the window appears similar to
Figure 46 below. Highlight and double-click on the Security option in the center pane.
Figure 46: Global Menu with Security Option Highlighted
2.
If the system is locked, the window is similar to Figure 47 below.
Figure 47: Password Window
3.
Enter the current or default Password and click [Next Item].
DigitalFlow™ XGS868i Programming Manual
121
Appendix C. Programming the XGS868i Using PanaView™
Figure 48: Entering Password
4.
At the Lock Out prompt, click UNlck to unlock the system and return to the initial PROGRAM menu, or click LOCK to
lock the system.
5. At the Edit Password prompt, click No to leave the password unchanged, or click YES to enter a new password.
IMPORTANT: Since the default password is printed in this manual, a new password should be entered. If the
password is ever lost, contact the factory for assistance.
6.
7.
Enter the New Password and click Yes. Any combination of letters and numbers up to a total of 7 characters may
be used as a password.
Verify the New Password by re-entering it and click Yes. Be sure to record the new password in a safe place.
C.7
Exiting the Site Edit Menu
After leaving the Global submenu, PanaView returns to the Site Edit Menu. Click [Close] to exit the Site Edit Menu. Then
proceed to Chapter 3, Operation, of the Startup Guide for instructions on taking measurements, or refer to the
appropriate chapters of this manual for detailed instructions on using the other features of the XGS868i flow
transmitter.
122
DigitalFlow™ XGS868i Programming Manual
Appendix C. Programming the XGS868i Using PanaView™
C.8
Saving Site Data
The XGS868i holds setup parameters for a single internal site, called Working. Through PanaView, users can store site
file data in a PC and reload it into the XGS868i. To save or reload site data via PanaView:
1.
2.
In the New Meter Browser, highlight the XGS868i.
Right-click on the highlighted XGS868i and select the Properties option, as shown in Figure 49.
Figure 49: The Properties Option
The window now appears similar to Figure 50.
Figure 50: The Properties Window
for an XGS868i
DigitalFlow™ XGS868i Programming Manual
123
Appendix C. Programming the XGS868i Using PanaView™
3.
Click on the [Site Files] button. The Site File Operations window (shown in Figure 51) opens.
Figure 51: The Site File Operations Window
C.8.1 Saving Current Site Data to the Meter
To save existing site data to the meter:
1.
2.
Select the radio button for Selected and highlight an existing site in the left pane.
Then click on the [Save Site to Meter] button. A screen opens similar to Figure 52.
Figure 52: Site File Selection
3.
124
Highlight the desired site and click [Open]. PanaView sends the site to the meter.
DigitalFlow™ XGS868i Programming Manual
Appendix C. Programming the XGS868i Using PanaView™
C.8.2 Saving New Site Data to the XGS868i
To save new site data to the meter:
1.
2.
Select the radio button for New and click on the [Save Site to Meter] button.
A window opens similar to Figure 53. Enter the desired name, and click [OK].
Figure 53: Site Name Entry Window
3. The Site File Selection window (Figure 52 on page 124) opens. Highlight a site file with the desired settings, and
click [Open]. The site file becomes the Working site in the meter with the desired settings.
C.8.3 Saving a Site to the PC
To save a site to the PC:
1.
2.
3.
Highlight the desired site in the left pane. (See Figure 51 on page 124.)
Click [Save Site to PC]. A window opens similar to Figure 52 on page 124.
Enter the desired site name and click [Save]. PanaView saves the site in the PanaView folder unless otherwise
specified.
Note: If you have created a site on the meter after opening the Site File Operations window, you must close and
reopen the window to click on the new site.
DigitalFlow™ XGS868i Programming Manual
125
Appendix C. Programming the XGS868i Using PanaView™
C.8.4 Clearing a Site from the Meter
As the XGS868i has only one site (Working) at any time, it is not possible to remove this site. To change site
parameters, first save a site to the PC (as discussed in Saving a Site to the PC on page 125), and then save the site to
the XGS868i (as discussed in Saving New Site Data to the XGS868i on page 125).
C.8.5 Saving Site Data in Text Form
To store the data from a site file as a text file for display or printout:
1.
2.
3.
Highlight the site in the left pane. (See Figure 51 on page 124.)
Click on [Save Site Print to PC].
The Site File Selection window (shown in Figure 52 on page 124) opens. Enter the desired site name (now with a
.prt suffix) and click on [Save]. PanaView displays a text version of the site, as shown in Figure 54.
Figure 54: Printout of Site File
4.
Click [Close] once to close the Site File Operations window, and a second time to close the Properties window and
return to the Meter Browser.
126
DigitalFlow™ XGS868i Programming Manual
Appendix D. PanaView Menu Maps for the XGS868i
Appendix D. PanaView Menu Maps for the XGS868i
DigitalFlow™ XGS868i Programming Manual
127
Appendix D. PanaView Menu Maps for the XGS868i
128
DigitalFlow™ XGS868i Programming Manual
New Meter Browser
IDM
Edit Functions
XGS868I
SITE EDIT MENU
CALIBRATION/TEST
PAUSE MEASUREMENT
See Service Manual
Channel 1
Channel 2*
Global
System
Input/Output
Comm Port
Security
See Figure 55
See Figure 54
See Figure 54
1-Channel
SPEC
VOLUMETRIC UNITS
No
SPECIAL TRANSDUCER
Metric
Yes
FREQUENCY
100k
50k
Skan/Measure Mode
Skan Only
ASSUME SATURATION
STD
English
SET UP
See Figure D-2
ZERO CUTOFF
SITE/CHANNEL MESSAGE
Site Status
Burst
Burst
Input/Output
TRANSDUCER NUMBER
Channel Status
Off
STOP MEASUREMENT
Pipe Parameters
CHANNEL LABEL
2-Channel
MEASURE FLOW
See Figure 54
System
Status
PAUSE: Measure Flow
ACF
KACF
MMACF
ACM
KACM
MMACM
SCF
KSCF
MMSCF
SCM
KSCM
MMSCM
STEAM INPUT TYPE
200k
500k
25k
Temperature
33k
Tw
Skan/Measure
TEMP INPUT
(*only if input option is installed)
PIPE OD
English
Fixed
Metric
Slot1*
A:LABEL B:LABEL
VOLUMETRIC TIME
MASS FLOW UNITS
English
MASS FLOW ON
inch
MASS FLOW OFF
/SEC
Metric
/MIN
/HR
feet
in/PI
ft/PI
mm
m
mm/PI
m/PI
KLB
MMLB
TONS
KG
TONNE
PATH LENGTH P
VOL. DECIMAL DIGITS
0
1
Steam Input Type = Temp
English Metric
2
B
FIXED TEMP.
PIPE WALL
LB
A
/DAY
BASE TEMP.
PRESSURE INPUT
(*only if input option is installed)
3
Fixed
inch
MASS FLOW TIME
feet
mm
Slot1*
m
A:LABEL B:LABEL
TOTALIZER UNITS
/SEC
/MIN
/HR
/DAY
English Metric
AXIAL LENGTH L
English Metric
A
FIXED PRESSURE
MDOT DECIMAL DIGITS
0
1
MASS TOTALS
English
B
ACF
KACF
MMACF
ACM
KACM
MMACM
SCF
KSCF
MMSCF
SCM
KSCM
MMSCM
3
2
inch
feet
mm
BASE PRESSURE
m
Low Pressure Switch
NO
FLUID TYPE
Metric
Pressure
Figure 55: Channel X Menu - Status, System, Pipe and Input/Output Options
FILE
YES
PRESSURE LIMIT
Steam
TOTAL DECIMAL DIGITS
LB
KLB
MMLB
TONS
KG
Other
FLUID SOUNDSPEED
TONNE
0
1
2
3
QUALITY INPUT
F1
F2
Fixed
Slot1
REYNOLDS CORRECTION
A:LABEL B:LABEL
MASS DECIMAL DIGITS
Off
On
A
KINEMATIC VISCOSITY
0
1
2
3
CALIBRATION FACTOR
DigitalFlow™ XGS868i Programming Manual
B
FIXED QUAL.
129
New Meter Browser
IDM
Edit Functions
XGS868I
SITE EDIT MENU
CALIBRATION/TEST
PAUSE MEASUREMENT
See Service Manual
Channel 1
Channel 2*
Global
Input/Output
Comm Port
Security
See Figure 54
See Figure 55
See Figure 54
See Figure 54
System
Pipe Parameters
Input/Output
See Figure 52
See Figure 52
See Figure 52
See Figure 52
STOP MEASUREMENT
SET UP
V averaging
Default Setup
Signal Defaults?
MEASURE FLOW
System
Status
Signal
PAUSE: Measure Flow
Advanced Features
RESPONSE TIME
SIGNAL LOW LIMIT
NO
CORR. PEAK LIMIT
YES
1
2
5
30
60
STATS
Multiple K Factors
SKAN T OFFSET
SOUNDSPEED + – LIMIT
% OF PEAK
VELOCITY LOW LIMIT
M>S SWITCH
10
Mass Flow Calculation
Activate Multi K Fact?
Off
Mass from Static Dens?
No
On
Custom Type
VELOCITY HIGH LIMIT
Yes
Fluid Density
# SHIFTS
CstV
ACCELERATION LIMIT
A DIVISOR
AMP. DISCRIM LOW
# TRANSMIT PULSES
AMP. DISCRIM HIGH
T WINDOW
R WINDOW
CstR
Kin. Viscosity
Edit table?
NO
DELTA T OFFSET
Figure 56: Channel X Menu - Set Up Option
FILE
YES
Enter # of K Factors
Velocity (Reynolds) #*
K Factor #*
*Repeat for the # of K Factors entered previously.
DigitalFlow™ XGS868i Programming Manual
130
FILE
New Meter Browser
IDM
XGS868I
Edit Functions
SITE EDIT MENU
CALIBRATION/TEST
PAUSE MEASUREMENT
See Service Manual
Channel 1
Channel 2*
System
PAUSE: Measure Flow
Global
MEASURE FLOW
STOP MEASUREMENT
Input/Output
Meter Address
SYSTEM UNITS
BAUD RATE
Display
Options
Metric
See Figure 55
PRESSURE UNITS
English Metric
PSIg
BARa
BARg
Kpaa
HIGH
HOLD
LOW
HHIGH
OTHER
300
600
1200
4800
9600
19200
2400
Kpag
MODBUS option installed
1-CHANNEL UNITS
ATMOSPHERIC PRESSURE
2 PATH ERROR HANDLING
1-CHANNEL UNITS
MASS FLOW UNITS
English Metric
MASS FLOW ON
MASS FLOW OFF
MODBUS Baud Rate
2-CHANNEL UNITS
2-CHANNEL UNITS
YES
VOLUMETRIC UNITS
English Metric
2400
4800
9600
19200
NO
MODBUS Parity
LOCK OUT
# OF LCD PARAMS
LB
KLB
MMLB
TONS
KG
TONNE
ACF
KACF
MMACF
ACM
KACM
None
MMACM
OFF
SCF
KSCF
MMSCF
SCM
KSCM
1
3
2
4
Odd
Even
UNlck
LOCK
ENTER PASSWORD
KEY
? EDIT PASSWORD
MMSCM
MODBUS Stop Bits
(appears only for 2-Channel meter)
MASS FLOW TIME
/SEC
/MIN
(until all channels set up)
NO
/HR
1 Bit
VOLUMETRIC TIME
/DAY
/SEC
/MIN
CH1
/HR
CH2
SUM
DIF
AVE
MODBUS Address
Measurement Name
VOL DECIMAL DIGITS
1
2
3
0
MASS TOTALS
English Metric
LB
KLB
MMLB
TONS
KG
1
2
TOTALIZER UNITS
English Metric
TONNE
ACF
KACF
MMACF
ACM
KACM
MMACM
SCF
KSCF
MMSCF
SCM
KSCM
MMSCM
MASS DECIMAL DIGITS
0
1
2
3
TOTAL DECIMAL DIGITS
0
DigitalFlow™ XGS868i Programming Manual
VEL
3
1
2
VOLUM +TOTL
–TOTL
TIME
MDOT
+MASS –MASS
SS up
SS do
SNDSP
T up
Tdown
DELTA
REYN#
Tot K
PEAK%
Qup
Qdown
AMPup
AMPdn
CNTup
CNTdn
P#up
P#dn
TEMP
PRESR
Z
AcVOL
StVOL
Vinst
Tsat
Tsupr
Rho
Kelvn
kPa
YES
ENTER NEW PASSWORD
VERIFY NEW PASSWORD
/DAY
MDOT DECIMAL DIGITS
0
2 Bits
Figure 57: Global Menu - System, Display and Comm Port Options
Error Handling
Eng
PSIa
Security
Comm Port
METER MESSAGE
QUAL
3
131
FILE
New Meter Browser
IDM
XGS868I
Edit Functions
SITE EDIT MENU
CALIBRATION/TEST
PAUSE MEASUREMENT
See Service Manual
Channel 1
Channel 2*
PAUSE: Measure Flow
Global
MEASURE FLOW
STOP MEASUREMENT
See Figures 52 and 53
System
Input/Output
See Figure 54
Error Handling
Comm Port
Security
See Figure 54
See Figure 54
Display
Options
See Figure 54
See Figure 54
I/O
SLOT0
(appears only if option card is installed)
SLOT1
Slot 0 Outputs
Totalizer Outputs
Frequency Outputs
B
A
B
C
A
D
Alarm Relays
C
B
D
A
B
C
D
LOW
FAULT
Slot 0 Output A
Slot 1 Outputs
Off
0-20m
4-20m
Slot 1 Outputs
Slot 1 Outputs
FREQ
OFF
Channel
OFF
(appears only for 2-Channel meter)
TTLZR
OFF
Channel
CH1
CH2
SUM
DIF
AVE
Channel
Measurement Name
CH1
CH2
(appears only for 2-Channel meter)
SUM
DIF
CH1
CH2
HIGH
(appears only for 2-Channel meter)
SUM
DIF
Failsafe?
AVE
NO
AVE
YES
Measurement Name
VEL
VOLUM
+TOTL
–TOTL
TIME
MDOT
A
+MASS
–MASS
SS up
SS do
SNDSP
Measurement Name
B
T up
+TOTL
–TOTL
+MASS
–MASS
VEL
VOLUM
+TOTL
–TOTL
TIME
MDOT
+MASS
–MASS
SS up
SS do
SNDSP
T up
Tdown
DELTA
REYN#
Tot K
PEAK%
Qup
Qdown
AMPup
AMPdn
CNTup
CNTdn
P#up
P#dn
TEMP
PRESR
Z
AcVOL
StVOL
Vinst
Tsat
Tsupr
Rho
Kelvn
kPa
Channel (appears only for 2-Channel meter)
CH1
Slot 1 Outputs
Tdown
DELTA
REYN#
Tot K
PEAK%
Qup
Off
Qdown
AMPup
AMPdn
CNTup
CNTdn
0-20m
TEMP
PRESR
Z
AcVOL
Tsat
Tsupr
Rho
Kelvn
(appears only for 2-Channel meter)
StVOL
CH1
Vinst
UNITS/PULSE
4-20m
P#up
Channel
P#dn
MINIMUM ON
PULSE TIME
kPa
CH2
SUM
DIF
QUAL
B
C
+TOTL
–TOTL
TIME
MDOT
OFF
–MASS
SS up
SS do
SNDSP
DELTA
REYN#
Tot K
PEAK%
FLOW
OTHER
ALL
QUAL
T up
HIGH/LOW
Measurement Name
VEL
VOLUM
+TOTL
–TOTL
TIME
MDOT
+MASS
–MASS
SS up
SS do
SNDSP
T up
Tdown
DELTA
REYN#
Tot K
PEAK%
Qup
Qdown
AMPup
AMPdn
CNTup
CNTdn
P#up
P#dn
TEMP
PRESR
Z
AcVOL
StVOL
Vinst
Tsat
Tsupr
Rho
Kelvn
kPa
Analog Inputs
High
A
Tdown
Fault Type
FULL
TEMP
Low
+MASS
FAULT
BASE
FULL SCALE FREQUENCY
VOLUM
AVE
D
Input measurement
VEL
DIF
LABEL
Measurement Name
ZERO
FULL
SUM
RTD Inputs
A
AVE
CH2
Figure 58: Global Menu - Input/Output Option
Analog Outputs
A
B
C
D
Qup
LABEL
NOTE: Plain text represents prompt area messages and
boxed text represents option bar choices.
Fx represent function keys to select option bar choices.
Qdown
AMPup
AMPdn
CNTup
CNTdn
P#up
P#dn
TEMP
PRESR
Z
AcVOL
StVOL
Vinst
Tsat
Tsupr
Rho
Kelvn
kPa
Input measurement
OFF
PRESR
TEMP
SPEC
INPUT NAME
QUAL
QUAL
INPUT UNITS
ZERO Value
ZERO
FULL
DigitalFlow™ XGS868i Programming Manual
FULL Scale Value
Trigger point
(All diagnostic parameters
appear here.)
132
Appendix E. Foundation Fieldbus Communications
Appendix E. Foundation Fieldbus Communications
E.1
Introduction
Foundation Fieldbus provides a means of communicating with the flowmeter. The patent numbers which apply are
5,909,363 and 6,424,872.
This Foundation Fieldbus device supports 6 Analog Input (AI) blocks, which can be configured to supply the following
measurements on the network (see Table 32).
Table 32: Available Measurements for the XGS868i
Units
Channel 2
Units
Average
Channel 1
Ch1 Velocity
ft/s or m/s* Ch2 Velocity
ft/s or m/s* Avg Velocity
Units
ft/s or m/s*
Ch1 Act
Volumetric
VOL_U
Ch2 Act
Volumetric
VOL_U
Avg Act
Volumetric
VOL_U
Ch1 Std
Volumetric
VOL_U
Ch2 Std
Volumetric
VOL_U
Avg Std
Volumetric
VOL_U
Ch1 Fwd Totals
TOT_U
Ch2 Fwd Totals
TOT_U
Avg Fwd Totals
TOT_U
Ch1 Rev Totals
TOT_U
Ch2 Rev Totals
TOT_U
Avg Rev Totals
TOT_U
Ch1 #Tot Digits**
none
Ch2 #Tot Digits**
none
Avg #Tot Digits
none
Ch1 Mass Flow
MASS_U
Ch2 Mass Flow
MASS_U
Avg Mass Flow
MASS_U
Ch1 Fwd Mass
Totals
MTOT_U
Ch2 Fwd Mass
Totals
MTOT_U
Avg Fwd Mass
Totals
MTOT_U
Ch1 Rev Mass
Totals
MTOT_U
Ch2 Rev Mass
Totals
MTOT_U
Avg Rev Mass
Totals
MTOT_U
Ch1 #Mass Tot
Digits
none
Ch2 #Mass Tot
Digits
none
Avg #Mass Tot
Digits
none
Ch1 Timer
sec
Ch2 Timer
sec
Avg Timer
sec
Ch1 Error Code
none
Ch2 Error Code
none
Avg Error Code
none
Ch1 SSUP
none
Ch2 SSUP
none
Avg SSUP
none
Ch1 SSDN
none
Ch2 SSDN
none
Avg SSDN
none
Ch1 Sound Speed
ft/s or m/s* Ch2 Sound Speed
ft/s or m/s* Avg Sound Speed
Ch1 Density***
see note
Ch2 Density***
see note
Ch1 Temperature
Deg F or C*
Ch2 Temperature
Deg F or C*
Ch1 Pressure
PRESS_U
Ch2 Pressure
PRESS_U
ft/s or m/s*
*Metric or English units are determined by the setup of the flowmeter.
**Totalizer digits are available for informational purposes only. Respective totals are automatically
scaled by the Tot Digits value selected in the flowmeter setup.
***If the meter is outputting Mole Weight, the unit is “mw”, otherwise it is the programmed pressure
unit.
VOL_U, TOT_U, MASS_U, MTOT_U and PRESS_U are determined by the units chosen for these
measurements in the flowmeter setup. See the instrument User's Manual for the setup of these
parameters.
DigitalFlow™ XGS868i Programming Manual
133
Appendix E. Foundation Fieldbus Communications
E.2
Configuration Utility Setup
The following is an example setup using National Instruments Configuration Utility v3.1.
Figure 59 shows the Configuration Utility with a flowmeter on the network (Panametrics Flow-XGM).
XGM
Figure 59: Configuration Utility Setup Example
Note:
The following procedures assume that the device has been placed in the OOS (out-of-service) mode before
executing.
E.3
Selecting the Desired Measurements
To set the measurement unit for each AI:
1.
2.
Double click on the FLOW Transducer Block (in the tree under GEFlow-XGM).
Select the Others tab and open the drop down list for the PRIMARY_SELECTOR and SECONDARY_SELECTOR (refer
to Figure 60 on page 135).
3. Choose the unit from the list (see Figure 60 on page 135).
This unit will correspond to the unit that is available in the AI block for network connection. The PRIMARY_SELECTOR
unit will correspond to ANALOG_INPUT_1 and the SECONDARY_SELECTOR will correspond to ANALOG_INPUT_2.
134
DigitalFlow™ XGS868i Programming Manual
Appendix E. Foundation Fieldbus Communications
E.3
Selecting the Desired Measurements (cont.)
4. After the desired measurements have been selected for the PRIMARY and SECONDARY SELECTOR, choose the
unit system (UNIT_SELECTOR above the PRIMARY_SELECTOR) that has been programmed in the flowmeter
(English or SI).
Figure 60: Primary Selector Drop Down List
DigitalFlow™ XGS868i Programming Manual
135
Appendix E. Foundation Fieldbus Communications
E.4
Selecting Units for AI Blocks
To select the units for the individual AI blocks:
1.
2.
Double click on the AI block for which you wish to set the units (ANALOG_INPUT_1 or ANALOG_INPUT_2 in the tree
under GEFlow-XGM; see Figure 59 on page 134).
Select the Scaling tab and set the unit for the measurement based on the flowmeter settings.
For example, if the flowmeter was set to use the metric unit system and the PRIMARY_SELECTOR was set to use
VELOCITY you would choose m/s for the unit as shown in Figure 61.
Figure 61: Units Index Drop Down List
136
DigitalFlow™ XGS868i Programming Manual
Appendix E. Foundation Fieldbus Communications
E.5
Resetting Instrument Totalizers
To reset the instrument totalizers:
1.
2.
3.
4.
Double click on the FLOW transducer block (in the tree under GEFlow-XGM; see Figure 59 on page 134).
Select the Others tab and scroll down to the CLEAR_TOTALIZERS listing.
Select Clear from the drop down list box (see Figure 62).
After the totals have been reset, select Normal from the drop down list box to resume total accumulation.
Figure 62: Clear Totalizers Drop Down List
DigitalFlow™ XGS868i Programming Manual
137
Appendix E. Foundation Fieldbus Communications
E.6
Function Block Application
Figure 63 is an example setup using the Function Block Application editor. The flowmeter AI blocks, along with the AO and
PID of another device on the network, are displayed. We have connected the AI_1 OUT of the flowmeter to the CAS IN
of the AO block. We have also connected the AI_2 OUT of the flowmeter to the CAS IN of the PID block.
XGM
Figure 63: Function Block Application
138
DigitalFlow™ XGS868i Programming Manual
Appendix F. Foundation Fieldbus Tables
Appendix F. Foundation Fieldbus Tables
Model
Table 33: Panametrics Fieldbus Device Capability, XGX868 Family of Meter Types
GF868, GS868, GM868, XGF868i, XGM868i, and
XGS868i
1 --General
1.1
Is the Device registered at the Fieldbus Foundation
(Yes/No)
Yes
1.2
Is the Unit released to production, and if not, when?
Yes
1.3
Is there any special functionality that device supports
(e.g., display blocks, diagnostic blocks)?
No
1.4
Manufacturer Name
1.5
Model
1.6
Device Type
0002
1.7
FF Device Revision
02
1.8
Does the device require special programming
software to configure a ‘good’ status on the PV?
Yes
1.9
Does the Device feature a Non-Volatile Memory
protection feature? If so, what are the steps to
disable/enable from the Resource or Transducer
block.
No
1.10
HOST System registered
Panametrics Measurement & Control
Panametrics Measurement & Control Gas
Flowmeter
Yokogawa (TBD), Emerson, Honeywell (TBD),
ABB (TBD)
1.11
Design Concept
Entity Concept
1.12
FISCO Compliant?
No
1.13
FNICO Compliant?
Yes: models XGM868i, XGS868i, XGF868i; No:
others
1.14
Hazardous Location Certs
GF868, GM868, GS868: CSA for non-incendive
Div 2, Class 1, Gr A, B, C, & D. IP66
Optional: Div 1, Class 1, Gr C & D or
ATEX II 2 G Ex d IIC T6 IP66 or
IECEx II2 G Ex d IIC T6 Gb IP66
XGM868i, XGS868i, XGF868i: CSA Div 1, Class 1, Gr
B, C, & D and ATEX II 2 G D Ex d IIC T5 IP66 and
IECEx II 2 G Ex d IIC T6 Gb IP66
1.15
FF Liquid PCB p/n:
XMT868i / DF868
1.16
FF Gas PCB p/n:
XGx868i / Gx868
1.17
Meter Software version (minimum and higher)
1.18
Firmware on FF card version
1.19
Interoperability Test Kit (ITK) revision
1.2
Protocol
1.21
Protocol Baud (bps)
703-1475-04 (rev J)/ 703-1491-04
GF868: GF3S; GM868:GM3Q; GS868: GS3N;
GC868: GC4C; XGM868i: Y4DM; XGS868: Y4DS;
XGF868i:Y4DF
868_GAS_FF_206
6.1.1
H1
31.25k
2 - DD and CFF
2.1
Device Description File Name (.ffo and .sym) and rev
DigitalFlow™ XGS868i Programming Manual
0203
139
Appendix F. Foundation Fieldbus Tables
2.2
Table 33: Panametrics Fieldbus Device Capability, XGX868 Family of Meter Types
Capabilities File Name and rev
020101.cff
2.3
Methods (list all methods available)
3.1
Polarity Sensitive (Yes / No)
Yes (Protected from failure if installed
incorrectly)
none
3- Physical
3.2
Quiescent Current Draw (mA)
10 mA idle / 18 mA max
3.3
Startup Current Draw (ma)
18 mA
3.32
Working voltage
3.33
Device Minimum Voltage
3.41
Device Resistance (Ohms) fieldbus terminal (+) to (-)
30 Mega Ohms increasing
3.42
Device Resistance (Ohms) fieldbus terminal (+) to
Ground
open circuit > 20 MOhm
3.43
Device Resistance (Ohms) fieldbus terminal (-) to
Ground
open circuit > 20 MOhm
3.51
Capacitance (microF) (+) to (-)
3.52
Capacitance (microF) (+) to Ground
3.53
Capacitance (microF) (-) to Ground
3.6
4-wire Device (if so, what AC/DC Voltage, Single or
3-phase
3.7
Connection type
4.1
Stack Manufacturer
4.2
Does the Device support Backup LAS functionality? (If
it does, then the functionality will be tested.)
9-32 VDC
9 VDC
1 pF
634.7 pF
635.7 pF
4 - Comm
Yes, (85-250 VAC 50/60 Hz, single phase or
12-28 VDC)
Terminal block, 2-wire twisted pair
National Instruments
No
4.3
4.4
Total Number of VCRs
4.5
Number of Fixed VCRs for user configuration
(Publisher, Subscriber, Alarming, and Trending)
20
1 fixed for System Management,
19 variable for user configuration
5 - User Layer General
5.1
Function Block Application Manufacturer
5.2
Function Blocks (list all type, but not including
transducer)
6 - AI(e), 1 - PID(e), 2 -TB(c), 1 - RB2(e)
Fieldbus Inc.
5.3
Device support block instantiation (Yes/No)
No
5.4
Number of Link Objects
20
5.5
Device support firmware upgrade over fieldbus
segment? (Yes/No)
No
5.6
Configuration write protect?
5.7
Zero trim, sensor trim, factory recall/ Upgrade device
master reset
Hardware jumper only
None
6 - Resource Block
140
6.1
Block Class (Std, Enhanced, Custom)
6.2
Special Features
Enhanced
Detailed errors, supported modes, revision id
and date
DigitalFlow™ XGS868i Programming Manual
Appendix F. Foundation Fieldbus Tables
Table 33: Panametrics Fieldbus Device Capability, XGX868 Family of Meter Types
7 - Transducer Blocks
7.1
Transducer Blocks based on which latest version of
the FF spec
FF-902 FS 1.4
7.2
Block Type
Flow/Display
7.3
Block Class (Std, Enhanced, Custom)
7.4
Custom/Custom
Does the Device support Methods in the Resource
and Transducer Blocks? (If it does, then the
functionality will be tested.)
No
Special Features besides Methods (multiple VIEWS,
etc.)
Multiple View3s and View4s
Device specific advanced diagnostics
Yes
8 - Function Blocks
8.1
Does the Device support Custom Function Blocks? An
example of custom block has Profile Number equal to
or greater than 0x8000. A standard enhanced block
has Profile Revision with 0xXXXX, where Enhancement
Number upper byte is non-zero (e.g. 0x5500 is en
8.2
Block Type
8.3
Number Available
8.4
Execution Time (ms)
8.5
Block Class (Std, Enhanced, Custom)
8.6
Function Block Special Features (e.g., Configuration
required for non-standard parameters by host)
9Channels
No
AI/PID
XD_SCALE and CHANNEL value
6/1
50/100
Enhanced
None
List by Channel, Unit Code, Enumerated
description, and Function Block Type (if
applicable)
9.1
Channel 0
n/a
9.2
Channel 1
Channel 1 - "Primary Value"/"Secondary Value"
AI Block
Units 1001 - degree Celsius
1002 - degree Fahrenheit
1034 - cubic meter (removed)
1043 - cubic feet
1053 - standard cubic foot
1061 - m/s
1067 - ft/s
1088 - kilogram
1092 - metric ton
1094 - pound (mass)
1095 - short ton
1097 - kilograms per cubic meter
1107 - pounds per cubic foot
1142 - pounds per square inch absolute
DigitalFlow™ XGS868i Programming Manual
141
Appendix F. Foundation Fieldbus Tables
Table 33: Panametrics Fieldbus Device Capability, XGX868 Family of Meter Types
1143 - pounds per square inch gauge
1324 - kilogram per hour
1360 - standard cubic feet per minute
1361 - standard cubic feet per hour
1526 - Standard cubic meter (20° 1 atm)
1547 - kilopascal absolute
1548 - kilopascal guage
1590 - bar guage (replaced with 34002)
1597 - Bar absolute (replaced with 34001)
1653 - cubic Megafeet per day (replaced with
34005)
33010 - thousands of actual cubic feet
(changed to 34028)
33015 - thousands of actual cubic meters
(changed to 34033)
33022 - thousands of standard cubic feet
(changed to 34038)
33026 - thousands of standard cubic meters
(changed to 34043)
33037 - millions of actual cubic feet (changed
to 34004)
33042 - millions of actual cubic meters (
changed to 34009)
33049 - millions of pounds (changed to 34003)
33054 - millions of standard cubic feet
(changed to 34014)
33058 - millions of standard cubic meters
(changed to 34023)
33063 - standard cubic feet per day (changed
to 34025)
33064 - standard cubic feet per second
(changed to 34026)
33065 - thousands of pounds (changed to
34027)
33066 - mole weight (changed to 34024)
33067 - thousands of kilograms (removed)
1322 - kilogram per second
1323 - kilogram per minute
1325 - kilogram per day
1326 - metric ton per second
1327 - metric ton per minute
1328 - metric ton per hour
1329 - metric ton per day
1330 - pound per second
1331 - pound per minute
1332 - pound per hour
142
DigitalFlow™ XGS868i Programming Manual
Appendix F. Foundation Fieldbus Tables
Table 33: Panametrics Fieldbus Device Capability, XGX868 Family of Meter Types
1333 - pound per day
1334 - short ton per second
1335 - short ton per minute
1336 - short ton per hour
1337 - short ton per day
1347 - cubic meter per second
1348 - cubic meter per minute
1349 - cubic meter per hour
1350 - cubic meter per day
1356 - cubic feet per second
1357 - cubic feet per minute
1358 - cubic feet per hour
1359 - cubic feet per day
1497 - cubic kilometer per second
1498 - cubic megameter per second
1501 - cubic kilometer per minute
1502 - cubic megameter per minute
1505 - cubic kilometer per hour
1506 - cubic megameter per hour
1509 - cubic kilometer per day
1510 - cubic megameter per day
1527 - Standard cubic meter per second (20°,
1atm)
1528 - Standard cubic meter per minute(20°,
1atm)
1529 - Standard cubic meter per hour (20°,
1atm)
1530 - Standard cubic meter per day (20°,
1atm)
34000 - Actual cubic meters
34001 - Bar absolute
34002 - bar gauge
34003 - million pounds
34004 - millions of actual cubic feet
34005 - Millions of actual cubic feet per day
34006 - Millions of actual cubic feet per hour
34007 - Millions of actual cubic feet per minute
34008 - Millions of actual cubic feet per second
34009 - millions of actual cubic meters
34010 - Millions of pounds per day
34011 - Millions of pounds per hour
34012 - Millions of pounds per minute
34013 - Millions of pounds per second
DigitalFlow™ XGS868i Programming Manual
143
Appendix F. Foundation Fieldbus Tables
Table 33: Panametrics Fieldbus Device Capability, XGX868 Family of Meter Types
34014 - millions of standard cubic feet
34015 - Millions of Standard cubic feet per day
34016 - Millions of Standard cubic feet per hour
34017 - Millions of Standard cubic feet per
minute
34018 - Millions of Standard cubic feet per
second
34019 - Millions of Standard cubic meter per
day
34020 - Millions of Standard cubic meter per
hour
34021 - Millions of Standard cubic meter per
minute
34022 - Millions of Standard cubic meter per
second
34023 - millions of standard cubic meters
34024 - mole weight
34025 - Standard cubic feet per day
34026 - Standard cubic feet per second
34027 - thousand pounds
34028 - Thousands of actual cubic feet
34029 - Thousands of actual cubic feet per day
34030 - Thousands of actual cubic feet per
hour
34031 - Thousands of actual cubic feet per
minute
34032 - Thousands of actual cubic feet per
second
34033 - Thousands of actual cubic meters
34034 - Thousands of pounds per day
34035 - Thousands of pounds per hour
34036 - Thousands of pounds per minute
34037 - Thousands of pounds per second
34038 - Thousands of standard cubic feet
34039 - Thousands of Standard cubic feet per
day
34040 - Thousands of Standard cubic feet per
hour
34041 - Thousands of Standard cubic feet per
minute
34042 - Thousands of Standard cubic feet per
second
34043 - Thousands of standard cubic meters
34044 - Thousands of Standard cubic meters
per day
34045 - Thousands of Standard cubic meters
per hour
144
DigitalFlow™ XGS868i Programming Manual
Appendix F. Foundation Fieldbus Tables
Table 33: Panametrics Fieldbus Device Capability, XGX868 Family of Meter Types
34046 - Thousands of Standard cubic meters
per minute
34047 - Thousands of Standard cubic meters
per second
9.3
Channel 2
Channel 2 - "Primary Value"/"Secondary
Value"
AI Block
Units same as channel 1
DigitalFlow™ XGS868i Programming Manual
145
Appendix F. Foundation Fieldbus Tables
[no content intended for this page]
146
DigitalFlow™ XGS868i Programming Manual
Index
Symbols
+MASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
+TOTL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
A
Acceleration Limit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 101
Activating a Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
AcVOL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Advanced Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Advanced Features Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Mass Flow Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Multiple K Factors Option. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Alarm Relays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Alarms
Option Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Setting Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Alarms Card, Setting Up in PanaView . . . . . . . . . . . . . . . . . . . . . 113
AMPdn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Amplitude Discriminator
High . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 101
Low. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 101
AMPup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Analog Inputs
Option Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
RTD Inputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Setting Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Analog Inputs Card, Set Up in PanaView . . . . . . . . . . . . . . . . . . .111
Analog Outputs
Option Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Setting Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Slot 0, Setting Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Arrow Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Atmospheric Pressure, Enter in PanaView . . . . . . . . . . . . . . . . 104
Axial Length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
B
Base Pressure
Entering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13, 99
in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Base Temperature, Entering . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 99
Basic Programming
Minimum Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Burst Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 102
C
Calibration Factor
in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Channel
Activating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Entering Mass Flow Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7, 22
Entering Totalizer Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Entering Volumetric Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
System Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Channel Menu
I/O Submenu in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Set Up Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Channel Message
in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
DigitalFlow™ XGS868i Programming Manual
Clearing Totalizers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Clearing Transmitter Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Log File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Site Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
CNTdn. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
CNTup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Comm Port Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117
Communications Port
Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Setting Up MODBUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Setting Up with PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Contrast, Adjusting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Correlation Peak Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15, 101
D
Data Display on LCD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Data, Displaying Using PanaView . . . . . . . . . . . . . . . . . . . . . 44, 45
Default Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Submenu, Advanced Features Option . . . . . . . . . . . . . . . . . 102
DELTA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Delta T Offset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15, 101
Diagnostics
Acceleration Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15, 101
Amplitude Discriminator High . . . . . . . . . . . . . . . . . . . . . . .15, 101
Amplitude Discriminator Low . . . . . . . . . . . . . . . . . . . . . . . .15, 101
Correlation Peak Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15, 101
Delta T Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15, 101
Divisor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 102
M>S Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 102
Number of Shifts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 102
Number of Transmit Pulses . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Percent of Peak . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15, 101
R Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Signal Low Limit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15, 101
Skan T Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15, 101
Soundspeed Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15, 101
T Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 102
Transmit Pulses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Velocity High Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15, 101
Velocity Low Limit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15, 101
Displaying Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Displaying Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Divisor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Down Arrow Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
E
Edit Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Enter Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Error Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
2-Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24, 108
Selecting for One-Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Selecting for Two-Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Error Response Options in PanaView . . . . . . . . . . . . . . . . . . . . . 107
Escape Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Ethernet
Setting up with PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
147
Index
F
Fluid Type
Entering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97
Foundation Fieldbus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34, 133
Frequency Card, Setting Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Frequency Outputs
Option Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Setting Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Frequency, in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
FWD Mass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
FWD Total . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
G
Global
Entering Mass Flow Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Entering System Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Entering Totalizer Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22, 105
Entering Volumetric Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Global Menu
Comm Port Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117
I/O Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106, 116
Error Option107
LCD Option42
Options Option108
in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
System Submenu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104, 121
Global System Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104, 121
Global-I/O-Error. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Graph Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Graphing Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
I
I/O (Global) Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106, 107
LCD Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42, 116
Options Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
I/O in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
I/O Submenu
in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Zero Cutoff Value, Entering (PanaView). . . . . . . . . . . . . . . . 98
Initial Setup
Data Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Initialing Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Input/Output (Channel)
Low Pressure Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13, 99
Pressure Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12, 99
Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12, 99
Zero Cutoff Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Input/Output (Global)
Error Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Setting Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Input/Output Menu
Assume Saturation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 98
Quality Input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13, 100
Steam Input Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 98
Inputs and Outputs, Setting up (PanaView) . . . . . . . . . . . . . . 106
Inputs, Setting Up
in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
148
K
K Factors, Entering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
K(Re)*MultiK*KFactor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Keypad Program
Entering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Exiting if Unused . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
KV Input Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10, 18
L
LCD
Contrast, Adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42, 116
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
See Liquid Crystal Display
Left Arrow Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Liquid Crystal Display (Transmitter) . . . . . . . . . . . . . . . . . . . . . . . 41
Setting Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Setting Up in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Log File
Clearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Logs
Creating, Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Creating, PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Deleting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Graphing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60, 63
Naming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Viewing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Low Pressure Switch
Entering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Entering in PanaView. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
M
M>S Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16, 102
Magnetic Keypad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
-MASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Mass Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Activating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Activating in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Entering Channel Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7, 22
Entering Data in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Entering Global Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Mass Flow Data
in Global Menu (PanaView) . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
MDOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Memory
Clearing Log File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Clearing Site Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Clearing Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Menus
Edit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Meter Logs, Creating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
MODBUS
Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Setting up via PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
MODBUS Communications
Requesting Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Setting Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
DigitalFlow™ XGS868i Programming Manual
Index
Multiple K Factors
Entering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Multiple Parameter Text Displays . . . . . . . . . . . . . . . . . . . . . . . . . 46
Multiple Text Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
N
Numeric Values, Entering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
O
Option Card
Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Analog Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
Available Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Frequency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
RTD Inputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Setup Information Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Totalizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Totalizer/Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Option Card Setup
Alarm Relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Analog Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Analog Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Frequency Outputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
MODBUS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
RTD Inputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Totalizer Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Option Cards
Programming in PanaView. . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Output Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Outputs, Setting Up in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . 106
P
P#dn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
P#up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44, 45
Capabilities of . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Communication Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Entering Menu in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
Parameter, Selecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45, 48
Path Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
PC Logs, Creating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
PEAK%. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Percent of Peak . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 101
Pipe Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Pipe OD Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Pipe OD, Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9, 97
Pipe Parameters
Axial Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Entering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Entering in PanaView. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
OD/Circumference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Path Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Special Transducers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Wall Thickness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Pipe Wall Thickness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9, 97
PIPE, in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Plotting Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
PRESR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
DigitalFlow™ XGS868i Programming Manual
Pressure Input
Entering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Entering in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Pressure Units, Selecting in PanaView . . . . . . . . . . . . . . . . . . . . 104
Printing Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
PROG Menu, in Keypad Program . . . . . . . . . . . . . . . . . . . . . . . . . .39
Properties Option in Edit Menu (PanaView). . . . . . . . . . . . . . . 123
Pulses, Number of . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Q
Qdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Quality Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13, 100
Qup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
R
R Window (cycles) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Requesting MODBUS Parameters. . . . . . . . . . . . . . . . . . . . . . . . . .36
Response Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
REV Mass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
REV Total . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Reynolds Correction, in PanaView . . . . . . . . . . . . . . . . . . . . . . . . .97
Right Arrow Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
RTD Inputs Card, Setting Up in PanaView . . . . . . . . . . . . . . . . . .112
RTD Inputs, Setting Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
S
Safety
Auxiliary Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
General Issues. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
Personal Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Saturation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 98
Save Site Print to PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Save Site to Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Save Site to PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Saving Site Data, in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Selecting Measurement Method
in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
Serial Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117
Serial Communications, Setting Up . . . . . . . . . . . . . . . . . . . . . . .34
Serial Port, Setting up in PanaView . . . . . . . . . . . . . . . . . . . . . . . .117
Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
Set Up Submenu
in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Signal Option in PanaView. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Setup Data
Advanced Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Initializing/Default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Response Time-V Averaging . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Transducer Signal Parameters . . . . . . . . . . . . . . . . . . . . . . . . . 14
Setup Data Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Setup Submenu
Advanced Features Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Default Setup Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Signal Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
V Averaging Option. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Shifts, Number of . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
149
Index
Signal
Graph . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Low Limit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Plot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Reading in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Save . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Signal Low Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100, 101
Signal Option. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Transit-Time Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Signal, Transducer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Site Data
Clearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Site Data, Saving to PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Site Data, Saving to XGM868i. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Site Edit Menu, Global Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Site File Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Site, Clearing a . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Skan Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
Skan T Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 101
Skan/Measure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
Slot 0
Analog Outputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Setting Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Slot Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23, 106
SNDSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Soundspeed Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Special Transducers, Entering Number . . . . . . . . . . . . . . . . . . . . . 8
SS do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
SS up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Startup
See Basic Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Static Density, Activating in PanaView. . . . . . . . . . . . . . . . . . . . 103
Static Density, Entering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Status of Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Status Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
Steam Input Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 98
StVOL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
System (Global) Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . 104, 121
System Data
Channel, Entering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Entering in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Global, Entering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Mass Flow Units, Entering Channel . . . . . . . . . . . . . . . . . . . .7, 22
Mass Flow Units, Entering Global . . . . . . . . . . . . . . . . . . . . . . . . 22
Totalizer Units, Entering Channel. . . . . . . . . . . . . . . . . . . . . . . . . 6
Totalizer Units, Entering Global. . . . . . . . . . . . . . . . . . . . . 22, 105
Volumetric Units, Entering Channel . . . . . . . . . . . . . . . . . . . . . . 6
Volumetric Units, Entering Global . . . . . . . . . . . . . . . . . . . . . . . 21
System Units
in Global Menu (PanaView). . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
T
T Window (cycles) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 102
Tdown. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
TEMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
150
Temperature Input
Entering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Temperature Input, Entering in PanaView. . . . . . . . . . . . . . . . . 99
Text Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Time Delay (Tw), in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
TIMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Tot K . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Totalizer Card, Setting Up in PanaView . . . . . . . . . . . . . . . . . . . 114
Totalizer Outputs
Entering Channel Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Entering Global Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22, 105
Setting Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Totalizer Units, in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Totalizer/Frequency Card, Setting Up . . . . . . . . . . . . . . . . . . . . . 115
Totalizers
Clearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
-TOTL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Tracking Windows, Activating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Transducer Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
in PanaView. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Transducer Parameters, in PanaView. . . . . . . . . . . . . . . . . . . . . 96
Transducer Parameters, Programming . . . . . . . . . . . . . . . . . . . . 8
Transducer Signal Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Transducer Signals
Displaying in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Plotting in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Saving in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Transducers
Signal Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Special, Entering Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Transmit Pulses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Transmitter
Clearing Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Displaying Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
LCD, Setting Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
LCD, Setting Up in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Tup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Two-Path Error Handling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Typographical Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
U
Up Arrow Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
User Program
Global Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
I/O Submenu106, 108, 117
Error Option107
LCD Option42
LCD Option116
System Submenu104, 121
Minimum Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Status Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
V
V Averaging Option, in PanaView . . . . . . . . . . . . . . . . . . . . . . . . .102
V Averaging, Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
VEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
DigitalFlow™ XGS868i Programming Manual
Index
Velocity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
High Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Low Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Velocity High Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Velocity Low Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Viewing Logs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
VOLUM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Volumetric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Volumetric Units
Channel, Entering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Global, Entering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
in Global Menu (PanaView) . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
W
Windows
Resizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Tiling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
X
XGS868i, Adding on PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Z
Zero Cutoff Value, Entering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
in PanaView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
DigitalFlow™ XGS868i Programming Manual
151
Index
152
DigitalFlow™ XGS868i Programming Manual
Warranty
Warranty
Each instrument manufactured by Panametrics is warranted to be free from defects in material and workmanship.
Liability under this warranty is limited to restoring the instrument to normal operation or replacing the instrument, at
the sole discretion of Panametrics. Fuses and batteries are specifically excluded from any liability. This warranty is
effective from the date of delivery to the original purchaser. If Panametrics determines that the equipment was
defective, the warranty period is:
• One year from delivery for electronic or mechanical failures
• One year from delivery for sensor shelf life
If Panametrics determines that the equipment was damaged by misuse, improper installation, the use of
unauthorized replacement parts, or operating conditions outside the guidelines specified by Panametrics, the repairs
are not covered under this warranty.
The warranties set forth herein are exclusive and are in lieu of all other warranties whether
statutory, express or implied (including warranties or merchantability and fitness for a
particular purpose, and warranties arising from course of dealing or usage or trade).
Return Policy
If a Panametrics instrument malfunctions within the warranty period, the following procedure must be completed:
1.
Notify Panametrics, giving full details of the problem, and provide the model number and serial number of the
instrument. If the nature of the problem indicates the need for factory service, Panametrics will issue a RETURN
MATERIAL AUTHORIZATION (RMA), and shipping instructions for the return of the instrument to a service center will
be provided.
2.
If Panametrics instructs you to send your instrument to a service center, it must be shipped prepaid to the
authorized repair station indicated in the shipping instructions.
3.
Upon receipt, Panametrics will evaluate the instrument to determine the cause of the malfunction.
Then, one of the following courses of action will then be taken:
• If the damage is covered under the terms of the warranty, the instrument will be repaired at no cost to the
owner and returned.
• If Panametrics determines that the damage is not covered under the terms of the warranty, or if the warranty
has expired, an estimate for the cost of the repairs at standard rates will be provided. Upon receipt of the
owner’s approval to proceed, the instrument will be repaired and returned.
DigitalFlow™ XGS868i Programming Manual
153
Warranty
[no content intended for this page]
154
DigitalFlow™ XGS868i Programming Manual
Customer Support Centers
U.S.A.
The Boston Center
1100 Technology Park Drive
Billerica, MA 01821
U.S.A.
Tel: 800 833 9438 (toll-free)
978 437 1000
E-mail: [email protected]
Ireland
Sensing House
Shannon Free Zone East
Shannon, County Clare
Ireland
Tel: +353 (0)61 470200
E-mail: [email protected]
Scan here for Panametrics
support and service information
Copyright 2024 Baker Hughes company.
This material contains one or more registered
trademarks of Baker Hughes Company and its
subsidiaries in one or more countries. All third-party
product and company names are trademarks of their
respective holders.
BH059C31 EN J (03/2024)
">