Reference Table of contents iKnow Guide to Machine Safety REFERENCE

Reference Table of contents iKnow Guide to Machine Safety REFERENCE
REFERENCE
Reference Table of contents
iKnow® Guide to Machine Safety
Safeguarding Basics
Methods: Risk Assessment
Methods: Safety Circuits
Solutions: Comparing Guards and Devices
Solutions: Choosing and Locating a Safeguard
Requirement: Standards
Copper Wire Information
Magnet-Style Interlocks: Direction of Approach for Sensor/Magnet Pairs
Contact Configurations/Switching Diagrams
Page 206
207
207
208
209
210
211
212
213
Wiring Diagrams
Safety Light Screens
EZ-SCREEN 14 & 30 mm Resolution
220
EZ-SCREEN LP 14 & 25 mm Resolution
220
EZ-SCREEN Type 2 30 mm Resoultion
223
EZ-SCREEN Grids & Points
225
Safety Laser Scanners
230
Safety Controllers and Modules
PICO-GUARD
232
SC22-3 Safety Controllers
235
E-Stop & Guard
237
Universal Safety
248
Safety Mat
251
Muting Modules
252
Safe Speed
256
Extension Relay Modules
257
Interface Relay Modules
259
Two-Hand Control
DUO-TOUCH SG Modules
261
STB Self Checking Touch Buttons
262
DUO-TOUCH Run Bar with STB Buttons
265
Glossary
266
International Representatives
270
Index
276
More information online at
bannerengineering.com
205
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – iKNOW
Safeguarding Basics
Safety Interface
Machine Control
Machine
Hazard
PLC
FSD
iKNOW®
Emergency Stopping
CONTACT/SWITCHING
DIAGRAMS
Two-Hand Control
Personnel Protection
INTERNATIONAL
REPRESENTATIVES
GLOSSARY
HOOKUP
DIAGRAMS
Basics of Safeguarding
Machine and Personnel safeguarding refers to the combination of requirements, methods and solutions
used to protect people who come in contact with dangerous machines in the industrial environment.
Requirements
Device Requirements
National and regional governmental bodies have regulations, mandates,
standards and recommendations for implementing a safety method or a solution.
Safety devices must be able to consistently and reliably bring a
machine hazard to an orderly stop.
Key regulations regarding general machine guarding include the following:
• Machinery Directive - EU
• OSHA General Duty Clause – USA
To be considered a safety device, the following methods must be
used to ensure reliable operation: fault exclusion, redundancy, and
self-checking.
(see page 210 for an abridged version list of industry safety standards)
Safety Circuit Requirements
A safety stop circuit typically comprises of 2 normally open contact
from mechanically-linked relays. The circuit is monitored to detect
certain failures that could lead to the loss of the safety function.
206
More information online at
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – iKNOW
Methods: Risk Assessment
The Risk Assessment Process in machine safeguarding is a process
used to identify hazards through each phase of the machine’s life cycle
and to minimize dangers to personnel and equipment.
Risk Assessment Standards
• OSHA 3071, Job Hazard Analysis
• MIL-STD-8820, US DOD System Safety Program
• ANSI/RIA R15.06-1999, Safety Requirements for
Industrial Robots and Robot Systems
• ANSI B11.TR3, Risk Assessment and Risk Reduction
• ISO 14121 (EN 1050), Principles of Risk Assessment
• SEMI S10, Risk Assessment, Semiconductor
Manufacturing Equipment
The basic steps in a Risk Assessment Process:
1. Identify hazards and where they occur.
2. Assess risk by severity of harm and probability of occurrence.
3. Reduce the risk through the use of protective measures.
4. Validate and document results.
Methods: Safety Circuits
Depending on the level of risk associated with the machine or operations, an appropriate
level of control circuitry performance must be incorporated into safety device design.
Safety Stop Command
Monitoring Signal
Redundant Safety Stop Commands
Monitoring Signal
• Safety-rated components
• Integrated in accordance with
safety principles and design
• Redundancy not required
SafeGuarding
Device
SafeGuarding
Device
Machine
Stop
Machine
Stop
• Safety-rated components
• Conducts periodic test of system
• Normal operation allowed if no
faults are found
• If unsafe fault is found, system
will default to safe state or
indicate that unsafe system exists
• Safety-rated components
• Greatest degree of fault tolerance
• Redundancy and self-checking
• Single failure cannot cause loss of
safety function
• Faults detected immediately or at
next demand on system
Greater reliability, but possible
loss of safety function
Fault detected at each test
Safety function is ensured with a
single fault. An accumulation of
faults is not possible or detected.
Very Low
Minor bump or bruise with
no lost time
Low
Minor first aid, infrequent
exposure, or high likelihood of
avoiding the hazard
Mid Range
Injuries that are slight or normally
reversible, requiring normal healing
or only first aid.
High or Very High
Normally reserved for hand-fed
applications where injuries could be
severe to irreversible
—
Control Reliable ANSI B11.19
(Clause 6.1 and Annex C)
Not directly comparable to the
requirements of ISO 13849-1 and
exceeds a Category 2
—
ANSI / RIA
—
Simple
Single Channel
Single Channel with Monitoring
Control Reliable ANSI/RIA R15.06
(Clause 4.5)
Control reliability for robots typically
exceeds a Cat 3 but is not
necessarily intended to be a Cat 4
ISO / EN
ANSI / B11
Possible loss of safety function
Category B
ISO 13849-1/EN 954-1
Category 1
ISO 13849-1/EN 954-1
Category 2
ISO 13849-1/EN 954-1
Category 3 & 4
ISO 13849-1/EN 954-1
More information online at
bannerengineering.com
iKNOW®
Machine
Stop
CONTACT/SWITCHING
DIAGRAMS
SafeGuarding
Device
Fault
Generic
Safety Stop Command
Risk
• Non safety-rated components
• Integrated in accordance with
relevant standards
• Reliability depends on robust
components
• Redundancy not required
Dual with Monitoring
HOOKUP
DIAGRAMS
Machine
Stop
Simple
Device
Single with Monitoring
GLOSSARY
Stop Command
Single
INTERNATIONAL
REPRESENTATIVES
Basic
207
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – iKNOW
Solutions: Comparing Guards and Devices
Type
Safety Function
Advantages
Limitations
Requirements
Standards
Guards: protective physical barrier used to prevent access.
Fixed Guard
Provides a fixed
barrier to the hazard
• Low maintenance
• Long life
• Low cost for small areas
• Protects all individuals
• Can contain ejected
materials
• Poor ergonomics
• Limited visibility
• Limited access
• Costly for large areas
• Maintenance may require
removal of guard
• Protect from identified
hazard
• Prevent user from reaching
over, under, around or
through the barrier
• Provide safe openings
• ANSI B11.19
• ISO 14120
• ISO 13852
• ISO 13853
• ASME B15.1
Interlocked
Guard
Interrupts power to
machine when guard
is opened
• Low initial investment
• Can be placed close
to hazard
• Protects all individuals
• Can contain ejected materials
• Costly for large areas
• Increased maintenance
• Must be difficult to defeat
• Guard may open only after
machine has stopped– or
must be installed at a safe
distance
• ANSI B11.19
• NFPA 79
• ISO 14119
• IEC 60204-1
Safeguarding Devices: components, attachments or mechanisms designed to perform a specific safeguarding function.
INTERNATIONAL
REPRESENTATIVES
GLOSSARY
HOOKUP
DIAGRAMS
CONTACT/SWITCHING
DIAGRAMS
iKNOW®
Safety Light
Screen
Arrests power to
machine when sensing
field is interrupted
• Excellent ergonomics
• Allows frequent access
• Protects all individuals
• Cost effective for large areas
• Allows for good visibility
• Limited to machines that can
be stopped quickly
• No protection from ejected
parts
• May require the use of
additional guards
• May create a pass-through
hazard
• Limited to machines that can
be stopped quickly
• No protection from ejected
parts
• Large safety distance
• May create a pass-through
hazard
• Initiate immediate stop
when sensing field is
interrupted
• Appropriate resolution
required to detect objects
the size of a torso, ankle,
hand or finger
• ANSI B11.19
• IEC 61496
• ISO 13855
• Initiate immediate stop
when sensing field is
interrupted
• Appropriate resolution
required to detect objects
the size of a torso
• ANSI B11.19
• IEC 61496
• ISO 13855
Multiple-Beam Arrests power to
System:
machine when sensing
• Grids
field is interrupted
• Points
• Low initial investment
• Allows frequent access
• Allows for good visibility
• Protects all individuals
Two-Hand
Control
Operator must use
both hands to actuate
machine motion hereby
preventing operator
access to hazardous
area
• Operator’s hands are away
from hazardous area
• Low initial investment
• Low maintenance
• Potential ergonomic impact
• Provides protection only for
operator
• No protection from ejected
parts
• Concurrent actuation
• Release and reactivation
required before machine
motion may be reinitiated
• ANSI B11.19
• NFPA 79
• ISO 13855
• ISO 13856
• IEC 60204-1
Safety Mat
Monitor
Interrupts power to
machine when a
minimum pressure is
applied
• Excellent ergonomics
• Protects all individuals
• Allows for good visibility
• Costly for large areas
• Maintenance intensive
• Large safety distance
Minimum object sensitivity
of 66 lbs on and 3-1/8"
surface to detect a foot
• ANSI B11.19
• ISO 13855
• ISO 13856
• Overrides all other
functions and operations
• Reset of E-stop doesn’t
initiate machine motion
• Button must be red with
yellow background
• Should be located at each
operation station
• Final removal of power
done by electromechanical
components
• ANSI B11.19
• NFPA 79
• ISO 12100
• IEC 60204-1
• ISO 13850
Complementary Safety Devices: used to supplement a primary safeguard.
E-Stop
• Button
• Rope-Pull
Operator activates
button in emergency
situation to shut off
power to machine
• Immediate response
• Safe shutdown of machine
process
• Not considered a safeguard
• Requires conscious act of
operator
• Limits injury or machine
damage but typically does
not prevent it
*This represents a partial list of available safeguards & devices.
208
More information online at
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
iKnow
iKnow
V
V
I
I
S
S
I
I
O
O
N
N
REFERENCE – iKNOW
Supplementaland
Information
Solutions:
Locating a Safeguard
iKnowChoosing
Supplemental Information
iKnow
Choosing and Locating a Safety Product
Product
S A
F E a Tsafeguard,
Y
When
choosing
ask yourself the following questions:
Choosing
and Locating a Safety
A F2) isE it legal,
T Yand 3) does
1) isS it safe,
it make sense for the application.
Choosing a Safety Product
iKnow
iKnow
Locate
Locate
CloseClose
to Hazard
to Hazard
LongLong
Machine
Machine
StopStop
TimeTime
Ergonomic
Ergonomic
Visibility
Visibility
Multiple
Multiple
Operators
Operators
Guards
Guards
Against
Against
Ejected
Ejected
Material
Material
EHORFDWHG"
Infrequent
Infrequent
Access
Access
DVVRFLDWHGZLWKZKLFK
□WDVN"
:KDWDUHWKHW\SHVRI
□KD]DUGV"
:KDWDUHWKHW\SHVRI
□:KD]DUGV"
KHUHZLOOWKHVDIHJXDUG
EHORFDWHG"
□:KHUHZLOOWKHVDIHJXDUG
Frequent
Frequent
Access
Access
□:KRZLOOXVHLW"
I R E L E S S
□W
:KRZLOOXVHLW"
+RZZLOOWKH\XVHLW"
I hazards
R E LareE S S
□W
+RZZLOOWKH\XVHLW"
What
DVVRFLDWHGZLWKZKLFK
□ What
hazards are
WDVN"
Maintenance
Maintenance
$ $
Choosing a Safety Product
)L[HG+DUG*XDUG
/RFNLQJ*XDUG
P
P
P
P
E
E
E
E
E
E
P
P
P
P
E
E
E
E
/RFNLQJ*XDUG
,QWHUORFN*XDUG
P
P
P
P
E
A
E
E
E
A
P
P
P
P
E
E
E
E
Comments
‡/LPLWHGDFFHVV
‡/LPLWHGYLVLELOLW\WRWKHPDFKLQH
‡/LPLWHGDFFHVV
‡/LPLWHGYLVLELOLW\WRWKHPDFKLQH
‡/LPLWHGYLVLELOLW\WRWKHPDFKLQH
‡&RVWO\IRUODUJHDUHDV
‡/LPLWHGYLVLELOLW\WRWKHPDFKLQH
‡&RVWO\WRPDLQWDLQDQGIL[
‡&RVWO\IRUODUJHDUHDV
,QWHUORFN*XDUG
2-Hand Control
P
A
P
A
A
A
E
A
A
A
P
A
P
A
E
P
E
P
‡&RVWO\WRPDLQWDLQDQGIL[
‡2QO\SURWHFWVRSHUDWRUV
2-Hand Control
+LJK5HVROXWLRQ6/6
A
E
A
E
A
P
A
E
A
P
A
E
A
E
P
E
P
X
‡2QO\SURWHFWVRSHUDWRUV
‡/RFDWHFORVHUWRKD]DUG
+LJK5HVROXWLRQ6/6
/RZ5HVROXWLRQ6/6
E
E
E
E
P
P
E
E
P
P
E
E
E
E
E
E
X
X
‡/RFDWHFORVHUWRKD]DUG
‡&RVWVOHVVWKDQKLJKUHVROXWLRQ6/6
/RZ5HVROXWLRQ6/6
RU%HDP3HULPHWHU
E
E
E
A
P
A
E
P
P
A
E
E
E
E
E
E
X
X
‡&RVWVOHVVWKDQKLJKUHVROXWLRQ6/6
‡7DNHVOHVVVSDFHWKDQEHDP
RU%HDP3HULPHWHU
%HDP3HULPHWHU
E
E
A
A
A
A
P
P
A
A
E
E
E
E
E
E
X
X
‡7DNHVOHVVVSDFHWKDQEHDP
‡&RVWVOHVVWKDQRUEHDP
%HDP3HULPHWHU
6DIHW\0DWV
E
P
A
A
A
A
P
P
A
A
E
E
E
E
E
E
X
X
‡&RVWVOHVVWKDQRUEHDP
‡0DLQWHQDQFHLQWHQVLYH
6DIHW\0DWV
P
A
A
P
A
E
E
E
X
‡0DLQWHQDQFHLQWHQVLYH
(
$
(
3
$
;
3
;
([FHOOHQW
$FFHSWDEOH
([FHOOHQW
3RRU
$FFHSWDEOH
1RW$FFHSWDEOH
3RRU
1RW$FFHSWDEOH
Guarding Solutions
Guarding Solutions
)L[HG+DUG*XDUG
P
P
E
E
E
P
P
E
E
Comments
Two-hand control 'SI
High resolution safety light screen WR'SI
Low-resolution two-beam safety grid'SI
Low-resolution two-beam safety grid'SI
Horizontal sensing fields, LQFOXGLQJVDIHW\PDWV
KRUL]RQWDOVDIHW\OLJKWVFUHHQVDQGDUHDVFDQQLQJ
Horizontal sensing fields, LQFOXGLQJVDIHW\PDWV
GHYLFHV'SI
KRUL]RQWDOVDIHW\OLJKWVFUHHQVDQGDUHDVFDQQLQJ
GHYLFHV'SI
Low-resolution
three- or four-beam safety grid'SI
Low-resolution three- or four-beam safety grid'SI
Standard-resolution safety light screenWR´'SI
Standard-resolution safety light screenWR´'SI
High resolution safety light screen WR'SI
127(,OOXVWUDWLRQH[DPSOHVDUHEDVHGXSRQWKHGHVFULEHGVDIHJXDUGVEHLQJXVHGDVWKHSULPDU\VDIHJXDUGLQJGHYLFHDOOH[DPSOHVKDYLQJLGHQWLFDOVWRSSLQJWLPHDQG
IROORZLQJJHQHUDOO\DFFHSWHGLQGXVWULDOHQJLQHHULQJSUDFWLFHVWKDWDUHIRXQGZLWKLQ$16,%DQG$16,5,$5VDIHW\VWDQGDUGV
127(,OOXVWUDWLRQH[DPSOHVDUHEDVHGXSRQWKHGHVFULEHGVDIHJXDUGVEHLQJXVHGDVWKHSULPDU\VDIHJXDUGLQJGHYLFHDOOH[DPSOHVKDYLQJLGHQWLFDOVWRSSLQJWLPHDQG
IROORZLQJJHQHUDOO\DFFHSWHGLQGXVWULDOHQJLQHHULQJSUDFWLFHVWKDWDUHIRXQGZLWKLQ$16,%DQG$16,5,$5VDIHW\VWDQGDUGV
MS_T8_S1_E.pdf
MS_T8_S1_E.pdf
©%DQQHU(QJLQHHULQJ&RUS7HQWK$YH1R0LQQHDSROLV0186$‡3KRQH‡ZZZEDQQHUHQJLQHHULQJFRP‡(PDLOVHQVRUV#EDQQHUHQJLQHHULQJFRP
CONTACT/SWITCHING
DIAGRAMS
HOOKUP
DIAGRAMS
Hard guard or solenoid-locking guard
'SI
Hard guard or solenoid-locking guard
'SI
Standard or magnetic interlock hard guard
LQWHUORFNHGJXDUGRSHQVDZD\RUODWHUDOO\
Standard or magnetic interlock hard guard
IURPWKHKD]DUG'SI
LQWHUORFNHGJXDUGRSHQVDZD\RUODWHUDOO\
IURPWKHKD]DUG'SI
Two-hand control 'SI
Safety Distance
Ds = K (Ts + Tr) + Dpf
Safety Distance
Ds 6HSDUDWLRQ'LVWDQFHLQFKHV
Ds = K (Ts + Tr) + Dpf
K 26+$+DQG6SHHG&RQVWDQW
Ds 6HSDUDWLRQ'LVWDQFHLQFKHV
Ts 0DFKLQH5HVSRQVHVHF
K 26+$+DQG6SHHG&RQVWDQW
Tr 6DIHW\'HYLFHVHF
Ts 0DFKLQH5HVSRQVHVHF
Dpf 'HSWK3HQHWUDWLRQ)DFWRULQFKHV
Tr 6DIHW\'HYLFHVHF
Dpf 'HSWK3HQHWUDWLRQ)DFWRULQFKHV
GLOSSARY
Ds
K * Ttotal Ds + Dpf
K * Ttotal
+ Dpf
INTERNATIONAL
REPRESENTATIVES
Locating a Safety Product
iKNOW®
Locating a Safety Product
©%DQQHU(QJLQHHULQJ&RUS7HQWK$YH1R0LQQHDSROLV0186$‡3KRQH‡ZZZEDQQHUHQJLQHHULQJFRP‡(PDLOVHQVRUV#EDQQHUHQJLQHHULQJFRP
More information online at
bannerengineering.com
209
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – iKNOW
Requirements: Standards
Safeguarding standards are minimum
requirements for product and machine
design, manufacture, use and evaluation
that guide the methods used to improve
safety.
Go online for a more comprehensive
and up-to-date list of standards.
General Requirements
U.S.
OSHA 29CFR1910.212
General Requirements for (Guarding of)
All Machines
International/European
ISO 12100-1&2 (EN 292)
Safety of Machinery: Basic Concepts,
General Principles for Design
ISO 14121 (EN 1050)
Safety of Machinery: Risk Assessment
INTERNATIONAL
REPRESENTATIVES
GLOSSARY
HOOKUP
DIAGRAMS
CONTACT/SWITCHING
DIAGRAMS
iKNOW®
Standards: Safeguarding Design
U.S.
ANSI/NFPA 79
Electrical Standard for Industrial Machinery
ANSI Z535
Safety Signs, Symbols and Color Codes
ANSI Z136.1
Safe Use of Lasers
ANSI Z244.1 Lockout/Tagout of Energy
Sources
ANSI B11.21
Machine Tools Using Lasers – Safety
OSHA 29CFR1910.147
Control of Hazardous Energy
OSHA 29CFR1910.219
Mechanical Power Transmission Apparatus
ANSI/ASME B15.1
Mechanical Power Transmission Apparatus
ANSI B11.19
Safeguarding (Machine Tools)
ANSI B11.TR1
Ergonomic Guidelines
ANSI B11.TR3
Risk Assessment / Risk Reduction
ANSI B11.TR4
Programmable Electronic Systems (PES/PLC)
OSHA 3071
Job Hazard Analysis
International/European
IEC 60204-1
Electrical Equipment of Machines
ISO 14118 (EN 1037)
Prevention of Unexpected Start Up
ISO 13849-1 (EN 954-1)
Safety Related Parts of Control Systems
ISO 14120 (EN 953)
Guards – General Requirements for the
Design and Construction
210
More information online at
Standards: Specific Machine
Applications, Grouped by Type
Machine Tools
OSHA 29CFR1910.217
(Guarding of) Mechanical Power Press
ANSI B11.1
Mechanical Power Presses
EN 692
Mechanical Power Presses
More online....
Conveyors
ANSI/ASME B20.1
Conveyors and Related Equipment
ISO 4123
Belt Conveyors
ISO 9851
Overhead Electrical Monorail Conveyors
Industrial Robots
ANSI/RIA R15.06
Industrial Robots and Robot Systems
ISO 10218
Manipulating Industrial Robots – Safety
Injection Molding
ANSI B151.1
Horizontal Injection Molding Machines
ANSI B151.21
Injection Blow Molding Machines – Safety
ANSI B151.26
Dynamic Reaction – Injection Molding
Machines
ANSI B151.27
Plastics Machinery – Robots Used With HIM
Machines – Safety
Mills and Calenders
OSHA 29CFR1910.261
Pulp, Paper, and Paperboard Mills
OSHA 29CFR1910.216
Mills and Calenders in the Rubber and
Plastics Industry
ANSI B28.1
Safety Code for Rubber Mills and Calenders
EN 1417
Rubber and Plastics Machines – Two-Roll
Mills
Packaging
ANSI/PMMI B155.1
Packaging and Packaging-Related Converting
Machinery – Safety
EN 415
Safety of Packaging Machines
Semiconductor
SEMI S1
Safety Guideline for Equipment Safety Labels
SEMI S2
Environmental, Health, and Safety Guideline
for Semiconductor Manufacturing Equipment
SEMI S3
Safety Guidelines for Heated Chemical Baths
SEMI S7
Safety Guidelines for Environmental,
Safety, and Health (ESH) Evaluation of
Semiconductor Manufacturing Equipment
SEMI S8
Safety Guidelines for Ergonomics Engineering
of Semiconductor Manufacturing Equipment
SEMI S9
Safety Guideline for Electrical Design
Verification Tests for Semiconductor
Manufacturing Equipment
SEMI S10
Safety Guideline for Risk Assessment
And More…
Cranes, Printing, Woodworking,
Lumber and Logging
Safety Standards Acronyms
ANSI: American National Standards Institute
CE: Mark of European Conformity
CEN: European Committee for Standardization
CENELEC: European Committee for Electrotechnical
Standardization
CSA: Canadian Standards Association
EN: European Norm
IEC: International Electrotechnical Commission
ISO: International Organization for Standardization
MIL-STD: USA Military Standard
OSHA:Occupation Safety and Health Administration
UL: Underwriters Laboratory
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – iKNOW
Copper Wire Information
0.522
0.464
0.414
0.368
0.328
0.292
—
0.232
—
0.184
—
0.147
—
0.116
—
0.095
—
0.073
—
0.059
—
0.048
—
0.036
—
0.030
—
0.024
—
0.020
0.018
0.015
—
0.012
13.26
11.79
10.52
9.35
8.33
7.42
—
5.89
—
4.67
—
3.73
—
2.95
—
2.41
—
1.85
—
1.50
—
1.22
—
0.91
—
0.76
—
0.61
—
0.51
0.46
0.38
—
0.30
0.0050
0.0060
0.0080
0.010
0.012
0.016
0.020
0.025
0.030
0.040
0.050
0.060
0.080
0.10
0.13
0.16
0.20
0.25
0.32
0.40
0.50
0.64
0.80
1.0
1.3
1.6
2.0
2.6
3.2
4.1
5.2
6.5
8.2
10
HOOKUP
DIAGRAMS
xact diameter is dependent upon the wire gage used for the strands. Diameter listed represents the most common wire type for AWG.
E
Resistance values assume the resistivity of solid copper wire. Stranding and/or copper alloy increase the resistance values.
Trigonometric Formulas for Distance or Angle Calculation
Z
Y
Ø
Relationships:
sin ø = Y/Z
cos ø = X/Z
tan ø = X/Y
csc ø = Z/Y = 1/sin ø
sec ø = Z/X = 1/cos ø
cot ø = X/Y = 1/tan ø
GLOSSARY
2
11,687
10.406
9.266
8.252
7.348
6.543
5.827
5.189
4.620
4.115
3.665
3.264
2.906
2.588
2.304
2.052
1.829
1.628
1.450
1.290
1.151
1.024
0.912
0.813
0.724
0.643
0.574
0.511
0.455
0.404
0.361
0.320
0.287
0.254
X
Given ø and X: Y = X tan ø
Given ø and Y: X = Y cot ø Z = X sec ø
Z = Y csc ø
Given ø and Z: X = Z cos ø
Given X and Y: Z = √X2 + Y2
More information online at
INTERNATIONAL
REPRESENTATIVES
1
0.4601
0.4097
0.3648
0.3249
0.2893
0.2576
0.2294
0.2043
0.1819
0.1620
0.1443
0.1285
0.1144
0.1019
0.0907
0.0808
0.0720
0.0641
0.0571
0.0508
0.0453
0.0403
0.0359
0.0320
0.0285
0.0253
0.0226
0.0201
0.0179
0.0159
0.0142
0.0126
0.0113
0.0100
Approximate
Resistance per 100 feet
(30 meters)2
Ohms
iKNOW®
0000
000
00
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Approximate
Stranded Wire Diameter1
Inches
Millimeters
CONTACT/SWITCHING
DIAGRAMS
AWG
Solid Wire Diameter
American Wire or
Brown and Sharpe Gage
Inches
Millimeters
Y = Z sin ø
ø = arctan (Y/X)
bannerengineering.com
211
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
X1
y
X1
46
inn
de
M
a
C
46
98
98
9
30
30
9
1S M
D
AG
C
D
SI-M
V
M
a
de
1S M
V
AG
SI-M
in
G
G
erm
an
erm
an
y
REFERENCE – CONTACT/SWITCHING DIAGRAMS
YA
G1
MA
MM
SI-
Model SI-MAG1
Sensing
Face
X1
erm
an
y
de
M
a
y
errm
an
G
in
de
M
a
C
D
V
30
9
46
e
G
G
errm
an
y
erm
an
G
in
de
y
G
in
de
M
a
M
in
de
M
a
1S M
30
V
AG
9
SI-M
C
4
M 699
ad 1
e
in
46
y
2S
erm
an
SI-M
D
C
D
V
30
9
AG
46
M
y
2S
M 99
ad 1
e
in
AG
erm
an
SI-M
MM
M
5
XL
SI-M
G
G
in
de
a
M
C
D
98
46
AG
XL
98
y
V
SI-M
XL
9
erm
an
4
M 699
ad 1
e
in
YA
30
SI-M
1S M
AG2 S M
SI-MAG
98
99
46
99
0
46
M
G1
MA
2
S II--
X1
X1
1S M
46
SI-
AG
1S M
erm
an
y
errm
an
2
99
46
2S
erm
an
AG
G
99
SI-M
SI-M
G
XL
SM
MA
G
56 3 MM
98
7
4 46
M 69998
ad 1 9
e
in 30
G V
erm D
C
an
y Ma
M
a
C
D
V
98
46 9
99 3
2 0
46
X1
G
G
in
de
y
errm
an
G
in
de
M
a
C
C 46
D
V
AG
30
2S
46
MM
D
98
46
G
9
M 92
a
de
inn
AG
G
SI-M
4
M 699
ad 1
e
in
G1
MA
XI
S I-
YA
MM
G2
A
-M
SI
XL
4
M 699
ad 1
e
in
46
99
0
MM
AG
erm4
6
a n98
y9
M
SI-
0
SI-
AG
9
erm
an
y
SI-M
0
SI
YA
YA
V
46
D
98
46
99
0
YA
46
G1
A
-M
1S M M
AG AG2 M
SI-MSI- M
SI
1 SXLM
M
1 M -M AG
SI
M
in
de
M
a
YA
C
1S M
X1
MM
1S M
30
99
30
98
y
erm
an
YAAG 2
-M
y
46
M
2
2M
V
AG
9
99
0
SI-M
M
2S
y
G
inn
de
M
a
C
D
98
9
30
V
y
erm
an
G
inn
de
M
a
C
D
V
X1
YA
AG
30
G1
MA
M
SI-
G
MM
46
SI-
SI-
M
1S M
46
9
98
46
1M
G
MA
AG
9
X1
YA
YA
SI-M
AG
X1
erm
an
y
erm
an
G
in
de
M
a
C
D
SI-M
V
D
46
C
98
9
AG
SI-M
Movement is perpendicular to the sensing face.
X1
X1
1S M
30
in
de
M
a
1S M
V
y
erm
an
G
AG
SI-M
30
SI-M
1S M
C
Sensing
Face
Correct
Movement is perpendicular to the sensing face.
X1
X1
AG
MM
M 99
ad 1
e
in
M
erm4
6
a n 99
y0
2S
4
M 699
ad 1
e
in
AG
G1
MAXL
46
0
99
46
Correct
Correct
Y1AS M
AG
99
99
0
YA
SI-
Sensor
Movement is perpendicular to the sensing face.
D
9
98
46
99
G
SI-M
Coded Magnet
SI-
2
SI- 1 MM
MA
46
SI-
MM
46
99
46
G1
MA
X1
M -M
2 M SI
G
MA
98
M
in
G
inn
de
M
a
V
30
9
98
46
2M
AG
V
G
SI-M
YA
YA
D
D
V
30
98
46
G
MA
SM
30
erm
an
V
9
98
46
in
de
1
AG
SI-M
YA
SI-
1S M
y
D
C
M
a
X1
9
SI-M
M
0
SI-
1M
G
MA
errm
an
inn
de
1S M
M
a
1S M
AG YA
AG
C
46
98
G
9
30
erm
an
V
y
SI-M
y
G
erm
an
G
D
C
M
a
X1
46
y
y
X1
Sensor
in
de
1S M
2
X1
AG
SI-M
46
Coded Magnet
C
Coded
Magnet
Sensor
Model SI-MAG1
30
Sensing
Face
99
Magnet-Style Interlocks: Direction of Approach for Sensor/Magnet Pairs
Model SI-MAG1
M
0
46
99
0
SI-
Correct
Correct
Correct
Movement is parallel to the sensing face.
Movement is parallel to the sensing face.
Movement is parallel to the sensing face.
46
y
erm
an
I-MAG 3MM
S I569 87
XI
M
y
2S
erm
an
AG
erm
an
y
4
M 699
ad 1
e
in
SI-M
y
erm
an
in
de
G
in
erm
M
an
dye
M
a
M
2S
AG1 S M
SI-MAG
98 4
9 M 69
a3d 91
0eV
inD
CG
30
SI-M
46
46
46
46
98
9
SI-M
M 99
ad 1
e
in
AG
M 99
ad 1
e
D
C
1S M
V
AG
M
X1
XL
G
y
SI-M
erm
an
M
G
SI-M
2S
2S
46
X1
XL
AG
AG
M 99
ad 1
e
in
SI-M
G
M
erm
an
2S
4
M 699
ad 1
e
in
AG
G
SI-M
y
in
de
XL
1S M
M
a
AG
V
M-M
2 S SI
G
erm
an
9
98
46
M 99
ad 1
e
in
AG
4
M 699
ad 1
e
in
SI-M
4
M 699
ad 1
e
in
XL
XL
G
30 46
V 99
D 2
C
ASIG
C
y
errm
an
G
in
de
M
y
erm
an
G
4
M 699
ad 1
e
in
MM
a
errm
an
G
in
de
2
AG
- 1MS M
a
M
C
D
V
erm
4
a n 69
y 89
SI-M
MA
G
56 3 MM
98
7
y
an
erm
G
in
de
a
M
C
D
46
98
9
30
V
y
an
erm
G
in
de
a
M
C
D
V
30
9
98
y
an
erm
de
a
M
46
98
9
30
V
D
C
1S M
in
G
XI
AG
XL
M
y
2S
erm
an
AG
4
M 699
ad 1
e
in
SI-M
46
y
erm
an
SI-M
G
M
X1
46
XI
2S
1S M
y
AG
erm
an
SI-M
4
M 699
ad 1
e
in
M
y
2S
erm
an
AG
G
SI-M
M 99
ad 1
e
in
9
98
46
y
X1
G
y
M
erm
an
2S
G
AG
4
M 699
ad 1
e
in
SI-M
erm
an
G
in
de
M
a
C
1S M
V
AG
46
98
9
SI-M
30
MM
D
AG
I-MAG 3MM
S I569 87
XI
I-MAG 3MM
S I569 87
y
y
erm
an
G
in
de
M
a
C
D
30
V
AG
G
SI-M
M
2S
XL
4
M 699
ad 1
e
in
4
M 699
ad 1
e
in
SI-M
y
G
erm
an
M
4
M 699
ad 1
e
in
erm
an
y
SI-M
2S
2
XL
XL
I-MAG 3MM
S I569 87
46
99
46
y
errm
an
G
in
de
a
M
C
46
98
9
G1
MA
AG
AG
AG
X1
1S M
AG
AG
46
HOOKUP
DIAGRAMS
99
0
SI-
SI-M
XL
D
AG
G
G
YA
M
2S
SI-M
erm
an
M
G
2S
4
M 699
ad 1
e
in
AG
M 99
ad 1
e
in
SI-M
y
MM
XL
V
SI-M
y
M
erm
an
2S
4
M 699
ad 1
e
in
AG
1S M
30
C
D
V
30
99
G2
MA
2
4
M 699
ad 1
e
in 46
G 9
erm 92
an
y
G
inn
a
M
XL
9
98
46
0
SI-M
46
SI-
X1
erm
an
y
errm
an
G
in
de
9
98
46
2
G
MMA
SI2- S
AG
G
2
99
46
a
30
V
D
C
M
2
SI-M
46
99
erm
an
y
M 99
ad 1
e
in 46
G 9
erm 92
an
y
1S M
de
CONTACT/SWITCHING
DIAGRAMS
y
erm
an
G
inn
e
46
AG
YA
SI-M
SM
YA
MM
MA
G
56 3 MM
98
7
SI-M
MM
G2
MA
YA
SI-
XL
M
YA
XL
2M
1S M
YA
XL
G2
X1
AG
YA
XL
MM
XI
S II--
2
SI-M
MM
YA
MA
G
56 3 MM
98
7
SI-M
MA
YA
XL
MM
MA
G
56 3 MM
98
7
X1
X1
1S M
S I-
G1
MA
S II-XI
S I-
M
SI-
MA
G
56 3 MM
98
7
X1
2M
2
MM
MA
G
56 3 MM
98
7
46
SI-M
G2
MA
S II--
G
MA
S I-99 2
G
MMA
SI2- S
AG
YA
SI-
XI
XI
MA
G
56 3 MM
98
7
99
X1
S I-
Magnet orientation relative to magnet sensor
cable is incorrect.
46
M
XI
XI
S I-
Incorrect
Incorrect
Label to label approach of sensor and magnet
is not possible.
46
YA
2M
Correct
90° approach of sensor and magnet is
approved only for model SI-MAG1MM90.
G
MA
S I-99 2
iKNOW
®
46
99
0
M
G
SI SI
46
AG
2S
y
MM
1 M2 S
AGAG
- M-M
AG
D
y
1
YXA
XL
SI-M
46
YA
XL
MM
99
46
1S M
AG XL
erm
an
G1
MA
0
99
0
SI-
SI-M
G
46
SI-M
YA
MM
M
2S
y
2
99
46
YA
MM
30
MA
99
SI-
30
y
G
in
de
a
M
C
D
30
89
99
462
9
y
erm
an
G
inn
de
a
G2
M
C
SM
2
M AG 1
2S
AG SI-M
M 99
ad 1
e
in
46 G
98 erm
9
an
30 y
V
D
SI-M
46
AG
46
y
erm
an
de
inn
G
SI-M
V
2
99
46
a
C
D
V
30
9
98
46
0
99
46
G1
MA
MMXL
4
M 699
ad 1 4
6
e
in 99
G 0
erm
an
y
YA
SI-
XL
M
erm
an
G
in
de
a
M
C
D
V
30
9
98
46
YA
MM
errm
an
G
inn
de
a
M
C
D
V
30
9
98
46
2
99
y
46
y
erm
an
G
in
de
M
C
D
V
30
89
99
460
9
46
G1
MA
G1
MA
G4
e6rm
98
a9n
y
y
erm
an
y
erm
an
G
in
de
a
M
C
D
V
30
89
a
1S M
SI-
M
2S
XI
S II--
XL
YA
SI-
AG
X1
MA
G
56 3 MM
98
7
YA
SI-M
X1
MA
G
56 3 MM
98
7
M
1S M
XI
S II--
XI
S I-
2M
AG
GSI2-M
MA
G
MA
M
SI-M
SI-
X1
YA
SI-
2M
MMM
G11 S
MAAG
SISI- -M
X1
1
MA
G
56 3 MM
98
7
46
G2
MA
SI-
X1
AG
MM
S I-
YA
M
2M
G
MA
S I-99 2
X1
MA
A
SM Y
46
YA
SI-
MM
M
G
MA
S I-99 2
SI-M
M
G2
YA
X1
YA
YA
M
XI
X1
SM
1
AG
2M
M
SM
G
MA
S I-99 2
X1
1
AG
Incorrect
y
an
erm
in
de
a
M
C
D
y
an
y
erm
M
erm
in
de
G
a
9
98
V
D
C
de
a
M
1S M
30
AG
in
M
C
D
V
30
46
9
98
46
an
G
2S
SI-M
+
–
– NC
NO S
N
NO
N
y
AG
1S M
G
M 99
ad 1
e
in
SI-M
AG
46
46
30
9
98
30
9
98
46
y
M
erm
an
2S
4
M 699
ad 1
e
in
AG
X1
erm
an
y
erm
an
G
in
de
M
a
D
SI-M
I-MAG 3MM
S I569 87
XI
XI
XL
XL
C
1S M
V
AG
Sensing
Face
G
X1
SI-M
I-MAG 3MM
S I569 87
XI
I-MAG 3MM
S I569 87
y
erm
an
M
X1
G
4
M 699
ad 1
e
in
y
erm
an
G
M 99
ad 1
e
in
AG
2S
Sensor
46
Coded Magnet
NOTE: With SI-MAG1C Controller, approach speed for all magnet-style switches must be greater than 0.2 ms.
With GM-FA-10J Controller, approach speed must be greater than 0.1 ms.
bannerengineering.com
de
a
M
1S M
C
AG
in
G
erm
an
y
X1
SI-M
D
More information online at
V
212
I-MAG 3MM
I569 87
INTERNATIONAL
REPRESENTATIVES
SI-M
M
2S
AG
4
M 699
ad 1
e
in
SI-M
1S M
SI-M
G
y
erm
an
M
G
2
99
46
y
G
erm
an
2S
AG
30
GLOSSARY
y
errm
an
G
in
de
a
M
C
D
V
30
SI-M
AG
4
M 699
ad 1
e
in
XI
MA
G
56 3 MM
98
7
YA
XL
XL
M
XL
S II--
MA
G
56 3 MM
98
7
YA
2M
AG
XI
S II--
M
M
M
SI-
MA
G
56 3 MM
98
7
SI-M
2M
2S
S II--
MA
G
56 3 MM
98
7
M
AG
S I-
2M
SI-M
MA
G
56 3 MM
98
7
YA
XL
XI
XI
46
1S M
S I-
MA
G
56 3 MM
98
7
G
MA
S I-99 2
X1
XI
46
YA
X1
XI
S II--
MA
G
56 3 MM
98
7
G
MA
S I-99 2
S I-
90° approach of sensor and magnet is not possible.
V
XI
Detail of Interiors
Incorrect
Label to label approach of sensor and magnet
is not possible.
9
98
D
C
de
a
M
1S M
in
G
erm
an
y
46
X1
AG
0V
46
2M
M
YA
M
G
MA
S I-99 2
XI
S I-
XI
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – CONTACT/SWITCHING DIAGRAMS
SD001 - SI-HG63 Series
SD002 - SI-HG80 Series
Contact Configuration
Switching Diagram
Contact Configuration
12
gn
9°
rd
rd/wh
9°
11
12
2
rd/bk
1
3°
OFF State
10°
rd/ye
rd/wh
4 3
Open
Closed
Transition
SD003 - SI-LS31HGD Series
Contact Configuration
2
1
Page 130
Open
Closed
Transition
Page 131
SD004 - SI-LS31HGE Series
Switching Diagram
Lever in Normal Position
Contact Configuration
Switching Diagram
Lever in Normal Position
0°
Lever Rotated
12
23
24
Open
Closed
Transition
Page 132
SD005 - SI-LS31HGRD Series
Contact Configuration
90°
11
12
21
22
Switching Diagram
Contact Configuration
24
Lever Rotated
180°
11-12
21-22
11
12
21
22
11
12
24
0°
5°
8°
Lever Rotated
180°
180°
180°
0°
23
Switching Diagram
0°
0°
5°
8°
10°
Monitor
23
Page 132
Lever in Normal Position
0°
12
Open
Closed
Transition
SD006 - SI-LS31HGRE Series
Lever in Normal Position
11
±90°
iKNOW®
90°
HOOKUP
DIAGRAMS
11
0°
±90°
90°
CONTACT/SWITCHING
DIAGRAMS
0°
90°
12
22
Safety
Monitor
Safety
Lever Rotated
11
21
0°
±5°
±8°
Safety
12
24
0°
±5°
±8°
±10°
Safety
Monitor
11
23
11-12
21-22
11-12
23-24
0°
GLOSSARY
rd
22
3
INTERNATIONAL
REPRESENTATIVES
rd/wh
21
3°
4
Safety
gn
34
Non-Safety
rd/ye
33
3°
rd/wh
11-12
23-24
12
rd/bu
12
10°
rd/ye
6°
Safety
22
rd/bk
3°
11
OFF State
34
rd/bk
22
Operating
Angle
11
rd/ye
21
Safety
22
34
6°
Safety
rd
21
33
rd/bu
rd/bk
Operating
Angle
gn
34
Operating
Angle
33
rd/bu
Switching Diagram
ON State
1-2
ON State
0°
Open
Closed
Transition
Page 132
11
12
21
22
More information online at
Open
Closed
Transition
Page 132
bannerengineering.com
213
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – CONTACT/SWITCHING DIAGRAMS
SD007 - SI-LS31HGLD Series
Contact Configuration
SD008 - SI-LS31HGLE Series
Switching Diagram
Lever in Normal Position
Contact Configuration
Switching Diagram
Lever in Normal Position
0°
11-12
23-24
11-12
21-22
0°
24
Safety
Lever Rotated
180°
Monitor
23
11
12
21
22
0°
5°
8°
Lever Rotated
180°
180°
0º
180°
0°
11
23
12
24
Open
Closed
Transition
Page 132
SD009 - SI-LS31RTD Series
Contact Configuration
11
12
21
22
Open
Closed
Transition
Contact Configuration
Switching Diagram
Axle in Home Position 0°
0°/360°
0°/360°
315°
330°
350°
360°
iKNOW®
>45°
CONTACT/SWITCHING
DIAGRAMS
11
23
12
24
Open
Closed
Transition
Page 133
33
34
INTERNATIONAL
REPRESENTATIVES
Actuator Removed
15
16
25
26
33
34
Engaged
Disengaged
Open
Closed
Transition
More information online at
12
21
22
Open
Closed
Transition
Contact Configuration
Page 133
Switching Diagram
33-34
26
15-16
25-26
25
11
Actuator Engaged
Safety
Safety
Monitor
HOOKUP
DIAGRAMS
GLOSSARY
16
330°
350°
360°
SD012 - SI-LS83..D Series
Switching Diagram
Actuator Engaged
15
22
>45°
SD011 - SI-LS100 Series
Contact Configuration
21
0°
10°
30°
45°
Axle Rotated 45°
Safety
Monitor
Axle Rotated 45°
12
Safety
Safety
24
11
0
7.6
11
12
8.3
8.8
23
24
21.5
mm
Page 136
Actuator Removed
11-12
23-24
23
0°
10°
30°
45°
Engaged
0
4
4.3
4.4
Disengaged
Safety
Monitor
12
11-12
23-24
11-12
23-24
11
Page 132
SD010 - SI-LS31RTE Series
Switching Diagram
Axle in Home Position 0°
214
Safety
0°
5°
8°
10°
12
Safety
11
11
12
23
24
Open
Closed
Transition
21.5
mm
Page 136
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – CONTACT/SWITCHING DIAGRAMS
SD013 - SI-LS83..E Series
SD014 - SI-QS75 Series
Switching Diagram
Contact Configuration
Disengaged
Safety
Monitor
11
12
23
24
Contact Configuration
11-12
23-24
Engaged
0
2.4
3.2
3.4
Disengaged
Safety
Monitor
Actuator Removed
Open
Closed
Transition
21.5
mm
Switching Diagram
33
34
Actuator Removed
15
16
25
26
33
34
21
22
11-12
Engaged
0
6.2
7.2
Actuator Removed
Disengaged
11
12
21
22
Open
Closed
Transition
Contact Configuration
33-34
26
15-16
25-26
25
12
21.5
mm
Page 138
Switching Diagram
Actuator Engaged
0
3.0
3.5
5.0
Engaged
Disengaged
Safety
Safety
Monitor
16
Switching Diagram
SD018 - SI-LM40MKHD Series
Actuator Engaged
15
11
Page 138
SD017 - SI-QS90MF Series
Contact Configuration
Page 137
Actuator Engaged
12
24
Open
Closed
Transition
SD016 - SI-QS90ME Series
Switching Diagram
Actuator Engaged
23
21.5
mm
12
Page 136
SD015 - SI-QS90MD Series
11
Disengaged
11
Open
Closed
Transition
Contact Configuration
Actuator Removed
iKNOW®
22
6.2
7.2
CONTACT/SWITCHING
DIAGRAMS
21
0
Open
Closed
Transition
21.5
mm
11
12
23
24
Engaged
12
23
24
Disengaged
Open
Closed
Transition
Page 138
More information online at
0
9
10
11
Actuator Removed
11
HOOKUP
DIAGRAMS
12
Engaged
GLOSSARY
11
21.5
mm
12
40
mm
INTERNATIONAL
REPRESENTATIVES
Actuator Removed
11
Safety
22
0
4.2
4.5
11-12
21-22
21
Engaged
Safety
Safety
12
11-12
23-24
11
Actuator Engaged
11-12
21-22
Actuator Engaged
Switching Diagram
Safety
Monitor
Contact Configuration
Page 142
bannerengineering.com
215
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – CONTACT/SWITCHING DIAGRAMS
SD019 - SI-LM40MKHE Series
SD020 - SI-LM40MKF Series
Contact Configuration
Switching Diagram
Contact Configuration
11
14
Actuator Removed
Safety
Safety
12
21
22
Open
Closed
Transition
Switching Diagram
15
16
25
26
33
34
33-34
34
0
10.5
11
12
Disengaged
41
mm
* 1 mm of movement will open
contact
Open
Closed
Transition
Page 142
Contact Configuration
Switching Diagram
Actuator Engaged
11-12
23-24
24
33
Engaged
Page 142
Actuator Engaged
23
26
SD022 - SI-LM40MKVE Series
Contact Configuration
12
25
40
mm
SD021 - SI-LM40MKVD Series
11
16
Actuator Removed
Disengaged
11
15
Monitor
22
0
15-16
25-26
21
Engaged
Safety
Safety
12
Engaged
0
1*
3
11
12
21
22
11-12
21-22
11
Actuator Engaged
11-12
21-22
Actuator Engaged
Switching Diagram
Engaged
3
7
Open
Closed
Transition
Switching Diagram
Contact Configuration
44
13
14
E1
+
E2
–
Actuator Removed & Unlocked
14
21-22
13-14
0
Engaged
7.0
8.0
9.0
31
32
43
44
E1
+
E2
–
More information online at
Open
Closed
Transition
Monitor
Disengaged
Solenoid Monitor Contacts
13
216
Actuator
Contacts
Safety
HOOKUP
DIAGRAMS
32
43
GLOSSARY
INTERNATIONAL
REPRESENTATIVES
31
22
22
Page 142
Switching Diagram
Actuator Engaged & Locked
21
21
22
38
mm
SD024 - SI-LS42..MSH/MMH Series
Solenoid Monitor Contacts
Actuator
Contacts
21
Open
Closed
Transition
Actuator Engaged & Locked
Actuator
Contacts
12
Page 142
SD023 - SI-LS42..MSG/MMG Series
Contact Configuration
11
11
12
21
22
31
32
43
44
E1
+
E2
–
0
Engaged
7.0
9.0
Actuator Removed & Unlocked
41
mm
Pages 145-146
Solenoid Monitor Contacts
Disengaged
Actuator
Contacts
Solenoid Monitor Contacts
11
12
21
22
31
32
43
44
E1
+
E2
–
Open
Closed
Transition
Safety
24
Disengaged
Safety
Safety
23
Actuator Removed
38
mm
11-12
21-22
12
Safety
Monitor
11
Disengaged
7
Safety
CONTACT/SWITCHING
DIAGRAMS
iKNOW®
Actuator Removed
0
41
mm
Pages 145-146
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – CONTACT/SWITCHING DIAGRAMS
SD025 - SI-LS42..MSI/MMI Series
SD026 - SI-LS42..MSJ/MMJ Series
Contact Configuration
Switching Diagram
Contact Configuration
Actuator Engaged & Locked
Actuator
Contacts
41
42
21
22
13
14
E1
+
E2
–
Actuator Removed & Unlocked
42
E2
–
Open
Closed
Transition
Pages 145-146
SD027 - SI-QM100..MSG/MMG Series
11
12
21
22
31
32
Switching Diagram
Actuator
Contacts
11-12
21-22
Open
Closed
Transition
Pages 145-146
Switching Diagram
Solenoid Monitor Contacts
21-22
13-14
10
11
12
44
21
22
31
32
11
12
43
44
0 (0)
Engaged
10 (0.39)
11 (0.43)
12 (0.47)
Actuator Removed & Unlocked
31
32
13
14
43
44
Safety
Open
Closed
Transition
Solenoid Monitor Contacts
21
22
31
32
11
12
43
44
Page 147
SD029 - RP-RM83..LTE/LTR Series
Open
Closed
Transition
41 (1.61)
mm (in)
iKNOW®
22
Disengaged
Actuator
Contacts
CONTACT/SWITCHING
DIAGRAMS
21
41
mm
Monitor
Solenoid Monitor Contacts
Page 147
SD030 - RP-RM83..LT/LR Series
Contact Configuration
Switching Diagram
Contact Configuration
Run Position
Switching Diagram
Actuator
Contacts
12
11
12
23
24
23
24
Cable Pull or Break
2-3
Latch
11
12
11
12
23
24
23
24
S1
-6
-4.8
-4
-3
Tension
Set Point
133N/228N
Open
Closed
Aux.
Safety
Monitor
Pull (175N/300N)
Safety
Monitor
Latch
Solenoid Monitor Contacts
Solenoid Monitor Contacts
Aux.
23-24
11-12
S2
Break (91N/156N)
11
12
11
12
23
24
23
24
+3
+4
+4.8
+6
Latch
Solenoid Monitor Contacts
Pull (175N/300N)
mm
Page 158
11
12
11
12
23
24
23
24
More information online at
-6
-4.8
-4
Tension
Set Point
133N/228N
Latch
Cable Pull or Break
Actuator
Contacts
S2
Open
Closed
GLOSSARY
11
23-24
Break (91N/156N)
11-12
S1
HOOKUP
DIAGRAMS
Run Position
Solenoid Monitor Contacts
Actuator
Contacts
E2
–
21-22
13-14
0
Engaged
Disengaged
Actuator
Contacts
E1
+
Contact Configuration
Actuator Removed & Unlocked
Actuator
Contacts
42
Actuator Engaged & Locked
32
43
41
41
mm
+4
+4.8
+6
mm
INTERNATIONAL
REPRESENTATIVES
14
Solenoid Monitor Contacts
23-24
13
31
Disengaged
Actuator
Contacts
Solenoid Monitor Contacts
22
9.0
SD028 - SI-QM100..DMSH Series
Contact Configuration
21
–
Actuator Removed & Unlocked
Actuator Engaged & Locked
Actuator
Contacts
+
7.0
11-12
E1
+
32
E2
Safety
Monitor
14
31
E1
0
Engaged
Safety
13
22
42
Monitor
22
21
41
23-24
21
41
12
11-12
32
11
7.0
8.0
9.0
41
mm
Monitor
Solenoid Monitor Contacts
0
Safety
Monitor
31
Disengaged
Safety
Safety
Actuator
Contacts
Engaged
Safety
32
Safety
Safety
31
Solenoid Monitor Contacts
13-14
31-32
21-22
Solenoid Monitor Contacts
31-32
Actuator Engaged & Locked
Actuator
Contacts
Switching Diagram
Page 158
bannerengineering.com
217
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – CONTACT/SWITCHING DIAGRAMS
SD031 - RP-LS42F-75L Series
SD032 - RP-QM72D-6L Series
Contact Configuration
Switching Diagram
Cable Position
Cable Pulled or Cable Break
26
14
22
34
41
42
Latch
+5
Open
Closed
Transition
Page 158
SD033 - RP-QM72D-12L Series
Cable Position
14
25
26
13
14
25
26
Cable Break
13
14
25
26
6
120N
Open
Closed
Page 159
Cable Position
Switching Diagram
25-26
150N
13-14
Run Position
0
1.5
Cable Pulled
13
14
25
26
50N
11
26
Open
Closed
Page 159
SD035 - RP-QMT72F-12L Series
Cable Position
46
45-46
45
80N
25-26
33-34
26
34
0
2
Cable Pulled
GLOSSARY
14
25
26
Pull
Cable Break
13
13
180N
Open
Closed
Page 159
Cable Position
Switching Diagram
13
14
25
33
26
34
80N
INTERNATIONAL
REPRESENTATIVES
Cable Break
218
13
14
25
33
26
34
45
46
More information online at
8
200N
Open
Closed
mm
Page 159
14
25
33
26
34
Cable Break
13
14
25
26
33
34
8
200N
Open
Closed
Pull
Break
46
6
13
Break
26
34
45
Pull
Break
Pull
25
33
Break
14
0
2
Cable Pulled
6
13
mm
Run Position
13-14
HOOKUP
DIAGRAMS
14
25
33
26
SD036 - RP-QMT72E-12L Series
Switching Diagram
Run Position
13
25
25-26
33-34
14
25
mm
14
Break
Cable Break
13
7.5
240N
13
13-14
26
Pull
25
Break
iKNOW®
CONTACT/SWITCHING
DIAGRAMS
14
0
2
Cable Pulled
5
13
mm
SD034 - RP-QMT72D-20L Series
Switching Diagram
Run Position
13
25-26
4
+3
+3.8
mm
21
33
0
2
Cable Pulled
Tension
Set Point
240N
Pull (300N)
13
13-14
41-42
25
90N
Pull
42
14
Break
41
Latch
13
-3.8
-3
25-26
22
34
-5
13-14
14
21
33
21-22
33-34
Break (180N)
13-14
Run Position
13
Switching Diagram
Run Position
mm
Page 159
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – CONTACT/SWITCHING DIAGRAMS
SD037 - RP-LM40D-6 Series
SD038 - RP-LM40D-6L Series
Cable Position
Switching Diagram
Cable Position
25
26
1.6
26
4.4
70N
Cable Break
13
14
25
26
Open
Closed
Transition
Pull
25
3.6
Break
14
14
25
26
50N
0
1.2
Cable Pulled
Cable Pulled
13
13
25-26
0
13-14
25-26
50N
5.0
mm
13
14
25
26
Cable Break
Page 160
13
14
25
26
3.2 Latch
70N
Open
Closed
Transition
Pull
14
Break
13
Switching Diagram
Run Position
13-14
Run Position
4.8
mm
Page 160
SD039 - RP-QM90F-100L Series
Cable Position
Switching Diagram
40°
70N
11
11
23
Cable Pulled or Break
Lock
0
30°
40°
24
12
12
24
23
11
11
23
Open
Closed
Lock
iKNOW®
23
Lever
Left Right
30°
70N
CONTACT/SWITCHING
DIAGRAMS
24
Page 160
HOOKUP
DIAGRAMS
12
GLOSSARY
12
INTERNATIONAL
REPRESENTATIVES
24
11 - 12
23 - 24
11 - 12
23 - 24
Run Position
More information online at
bannerengineering.com
219
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD001
EZ-SCREEN­® System (Type 4)
Emitter
(standard)
8-Pin
Euro-Style
(Standard Emitter)
8-pin male
Euro-style†
0V dc
+24V dc
Bn (#1)
Gn/Ye (#7)
Bu (#6)
Page 23
Models
• EZ-SCREEN 14 & 30 mm
emitter models with 8-pin
Euro QD
Bk (#5)
n.c.*
Wh (#4)
n.c.*
Vi (#8)
Or (#3)
n.c.*
Or/Bk (#2)
n.c.*
n.c.*
*NOTE: Pins 2, 3, 4, 5, and 8 are not connected, or are paralleled
to same color wire from the 8-pin receiver cable
(see Section 3.7 and Figure 3-16).
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
5-Pin Euro-Style (Emitter with Test)
Emitter
(with TEST)
Models
5-pin male
Euro-style†
• EZ-SCREEN 14 & 30 mm
emitter models with 5-pin
Euro QD
0V dc
+24V dc
Bn (Pin #1)
Gn/Ye (#5)
Bu (#3)
Bk (#4)
Wh (#2)
†
Jumper or
open to test
See Euro-style connectors on page 179 for female mating cordset.
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
†
See Table 2.2 for further cable information
WD002
EZ-SCREEN­® LP System (Type 4)
8-Pin Euro-Style (Reset Hookup)
iKNOW®
+24V dc
8-pin male
Euro-style
face view
0V dc
Bn (Pin #1)
Bu (#6)
Page 31
Models
• EZ-SCREEN LP
14 & 25 mm emitter
models with 8-pin Euro QD
Bk (#5)
Wh (#4)
*NOTE: Pins 2, 3, 4 and 5 either are not
connected, or are paralleled to
same color wire from the 8-pin
receiver cable.
HOOKUP
DIAGRAMS
CONTACT/SWITCHING
DIAGRAMS
Gn/Ye (#7)
n.c.*
n.c.*
Vi (#8)
Or (#3)
Close to reset
n.c.*
Or/Bk (#2)
n.c.*
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
*NOTE: Pins 2, 3, 4 and 5 either are not connected, or are paralleled to same
8-Pin Euro-Style (Test Hookup)
color wire from the 8-pin receiver cable.
Models
GLOSSARY
+24V dc
8-pin male
Euro-style
face view
• EZ-SCREEN 14 & 25 mm
emitter models with 8-pin
Euro QD
Bn (Pin #1)
Gn/Ye (#7)
Bu (#6)
Bk (#5)
INTERNATIONAL
REPRESENTATIVES
0V dc
*NOTE: Pins 2, 3, 4 and 5 either are not
connected, or are paralleled to
same color wire from the 8-pin
receiver cable.
†
Wh (#4)
n.c.*
n.c.*
Vi (#8)
Or (#3)
Open to test
n.c.*
Or/Bk (#2)
n.c.*
See Euro-style connectors on page 179 for female mating cordset.
220
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
*NOTE: Pins 2, 3, 4 and 5 either are not connected, or are paralleled to same
color wire from the 8-pin receiver cable.
More information online at
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD003
EZ-SCREEN­® System (Type 4)
Receiver with 2 Solid-State OSSDs, 2 FSDs and 2-Channel EDM
+24V dc
8-pin male
Euro-style†
Page 22
Models
• EZ-SCREEN 14 &
30 mm receiver models
with 8-pin Euro QD
• EZ-SCREEN LP
14 & 25 mm emitter
models with 8-pin Euro QD
Bn (Pin #1)
+24V dc
Gn/Ye (#7)
Ground
Bu (#6)
0V dc
Bk (#5)
OSSD1
Wh (#4)
OSSD2
Vi (#8)
Reset *
Or (#3)
EDM1
Or/Bk (#2)
EDM2
0V dc
FSD1
FSD2
Single-Channel
Safety Stop
Circuit
Dual-Channel
Safety Stop
Circuit
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
NOTE: Do not exceed OSSD maximum load
capacitance specification.
* Trip (auto reset) not connected.
†
See Euro-style connectors on page 179 for female mating cordset.
WD004
See Table 2.2 for further
QDE-8..D cable information.
†
iKNOW®
EZ-SCREEN­® System (Type 4)
2 Solid-State OSSDs and 2-Channel EDM of SC22-3
Receiver
8-pin male
Euro-style†
Bn (Pin #1)
+24V dc
Gn/Ye (#7)
Ground
Bu (#6)
0V dc
Bk (#5)
OSSD1
Wh (#4)
OSSD2
Vi (#8)
Reset*
Or (#3)
EDM1
Or/Bk (#2)
EDM2
0V dc
CONTACT/SWITCHING
DIAGRAMS
+24V dc
• EZ-SCREEN 14 & 30 mm
emitter models with 8-pin
Euro QD
• EZ-SCREEN LP
14 & 25 mm models with
8-pin Euro QD
NOTE: EZ-SCREEN receiver
DIP switches are configured
for “Trip” (T) output and
2-channel EDM (E2). If the
Auxiliary output is to be used,
configure the EZ-SCREEN
receiver for 1-channel EDM
(E1) and connect pin #3 (Or) to
+24V dc.
S1
Jumper
*Trip (auto reset) – Not connected
S2
S3
SC22-3
Safety Controller
GLOSSARY
Models
HOOKUP
DIAGRAMS
Page 22
A1 A1 A2 A2
See Euro-style connections on
page xxx for female mating cordsets.
INTERNATIONAL
REPRESENTATIVES
†
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
* Trip (auto reset)- Not connected
†
See Euro-style connectors on page 179 for female mating cordset.
More information online at
bannerengineering.com
221
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD005
EZ-SCREEN­® System (Type 4)
1-Channel EDM of IM-T-9A Interface Module
8-pin male Euro-style†
+24V dc
0V dc
Bn (Pin #1)
Gn/Ye (#7)
Bu (#6)
Page 22
Models
Bk (#5)
Wh (#4)
• EZ-SCREEN
14 & 30 mm models
with 8-pin Euro QD
• EZ-SCREEN LP
14 & 25 mm models with
8-pin Euro QD
Vi (#8)
Reset
Or (#3)
Or/Bk (#2)
**
not
connected
IM-T-9A
Terminal Locations
IM-T-9A
S3
S1
K2
3 3 9
9
*Installation of transient (arc)
suppressors
)-4!
across the coils of MPCE1 and MPCE2 is
recommended (see Warning).
Machine
Control
**Other interfacing modules and solutions
available, see Section 2.3 or the
Banner Safety Catalog.
9 Arc Suppressors. See manual for
specific warnings.
** Trip (auto reset) not recommended.
†
See Euro-style connectors on page 179 for female mating cordset.
9 3 3
S2
Y3
Y4
Y1
Y2
13
14
23
24
MPCE
2
33
34
*
MPCE
1
*
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
Feedback (optional)
See Table 2.2 for further QDE-8D cable information. *
†
K1
S4
WD006
EZ-SCREEN­® System (Type 4)
8-pin male Euro-style†
+24V dc
0V dc
Bn (Pin #1)
Gn/Ye (#7)
Bu (#6)
Page 23
Models
Bk (#5)
• EZ-SCREEN 14 &
30 mm models with
8-pin Euro-style QD
• EZ-SCREEN LP
14 & 25 mm models with
8-pin Euro QD
Wh (#4)
Vi (#8)
Or (#3)
Reset
**
Or/Bk (#2)
IM-T-9A
Terminal Locations
GLOSSARY
HOOKUP
DIAGRAMS
CONTACT/SWITCHING
DIAGRAMS
iKNOW®
2-Channel EDM of IM-T-9A Interface Module
IM-T-9A
S3
INTERNATIONAL
REPRESENTATIVES
K1
S2
3 3 9
Y3
Y4
9
Y1
Y2
13
14
23
24
MPCE
2
33
34
*
)-4!
9 9 3 3
222
S1
K2
S4
Machine
Control
* Arc Suppressors.
See manual for specific warnings.
** Trip (auto reset) not recommended.
†
See Euro-style connectors on page 179 for female mating cordset.
More information online at
Feedback (optional)
MPCE
1
*
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD007
EZ-SCREEN­® System (Type 4)
Hookup of E-Stop Button to the Last Receiver in a Cascade
E-stop 1
E-stop 2
E-stop N
Page 22
bn
Models
22 awg
• EZ-SCREEN 14 & 30 mm
models
• EZ-SCREEN LP
14 & 25 mm models
wh
bu
bk
QDE2R4-8..D
Cable Pinout*
QDE2R4-8..D
Cable Pinout*
Brown (Ch 1a)
Pin #1 – Brown (Ch 1a)
Pin #5 – n.c
Black (Ch 1b)
Pin #2 – Black (Ch 1b)
Pin #6 – n.c.
Blue (Ch 2b)
Pin
#3
–
Blue
(Ch
2b)
Pin #7 – n.c.
n.c.
Pin #8 – White (Ch 2a)
n.c. Pin #4 – n.c.
Pin #1
Pin #2
Pin #3
Pin #4
Pin #5
Pin #6
Pin #7
Pin #8
n.c. * Standard M12/Euro-style cables (8-pin male QD) can also be used,
n.c. although pin number/wire color must be verified.
White (Ch 2a)
!
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
!
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
*Standard M12/Euro-style cables (8-pin male QD) can also
be used, although pin number/wire color must be verified.
WD008
EZ-SCREEN­® System (Type 2)
CONTACT/SWITCHING
DIAGRAMS
iKNOW®
Emitter
Page 39
Models
8-pin male
Euro-style†
+24V dc
0V dc
Bn (#1)
HOOKUP
DIAGRAMS
Gn/Ye (#7)
Bk (#5)
n.c.*
Wh (#4)
n.c.*
Vi (#8)
n.c.*
Or (#3)
n.c.*
Or/Bk (#2)
n.c.*
GLOSSARY
Bu (#6)
or are
paralleled
**NOTE:
NOTE: Pins
Pins2,2,3,3,4,4,5,5and
and88are
arenot
notconnected,
connected,
or are
paralleled to
tosame
samecolor
colorwire
wire from the
thereceiver
receivercable
cable.
(see Section 3.2.4 and Figures 3-17 and 3-18).
†
See Euro-style connectors on page 179 for female mating cordset.
More information online at
bannerengineering.com
INTERNATIONAL
REPRESENTATIVES
• EZ-SCREEN Type 2
30 mm models
223
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD009
EZ-SCREEN­® System (Type 2)
Receiver with 2 Solid-State OSSDs, 2 FSDs and Power Monitoring
+24V dc
Receiver
8-pin male Euro-style†
Page 39
Models
Bn (Pin #1)
+24V dc
Gn/Ye (#7)
Ground
Bu (#6)
0V dc
Bk (#5)
OSSD1
Wh (#4)
OSSD2
FSD
1
FSD
2
Manual Test
Automatic
or Reset
Test
(Latch or Lockout)
• EZ-SCREEN Type 2
30 mm models
Vi (#8)
0V dc
Reset/Test
FSD
Monitoring
Circuit
Or (#3)
n.c.
Or/Bk (#2)
n.c.
Single-Channel
Safety Stop
Circuit
NOTE: Pins 2 and 3 are not connected,
or are paralleled to same color wire
from the emitter cable and properly
terminated
Dual-Channel
Safety Stop
Circuit
See Section 2.2 for further
QDE-8..D cable information.
†
NOTE: Do not exceed OSSD maximum load
capacitance specification.
†
!
See Euro-style connectors on page 179 for female mating cordset.
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
WD010
EZ-SCREEN­® System (Type 2)
HOOKUP
DIAGRAMS
CONTACT/SWITCHING
DIAGRAMS
iKNOW®
Power Monitoring of IM-T-9A Interface Module
+24V dc
8-pin male Euro-style†
Page 39
Models
Bn (Pin #1)
+24V dc
Gn/Ye (#7)
Ground
Bu (#6)
0V dc
Bk (#5)
OSSD 1
0V dc
• EZ-SCREEN Type 2
30 mm models
IM-T-9A
Terminal Locations
S3
Wh (#4)
OSSD 2
Vi (#8)
Reset/
Test
N.C.
3 3 9
Or (#3)
9
GLOSSARY
NOTE: Pins 2 and 3 are not
connected, or are paralleled
to same color wire from the
emitter cable and properly
terminated.
IM-T-9A
Or/Bk (#2)
S4
S1
K2
K1
S2
Y3
Y4
Y1
Y2
13
14
23
24
33
34
MPCE Monitoring
n.c.
n.c.
L1/+Vdc
)-4!
INTERNATIONAL
REPRESENTATIVES
Machine
Control
9 MPCE
2
*
9 3 3
* Arc Suppressors. See manual for specific warnings.
†
See Euro-style connectors on page 179 for female mating cordset.
224
MPCE
1
More information online at
*
L2/-V dc
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD011
EZ-SCREEN­® System (Type 4)
Emitter
Receiver with 2 Solid-State OSSDs, 2 FSDs and 2-Channel EDM
+24V dc
Page 44
+24V dc
0V dc
0V dc
EZ-SCREEN
Models
Receiver
Emitter
• EZ-SCREEN Grid & Point
PE 1
dc Com 2
EZ-SCREEN
PE 1
+24V dc 3
dc Com 2
(Not Used) 4
+24V dc 3
RESET 5
Open to test
TEST2 4
or
TEST1 5
Auxiliary power
connections
dc Com 8
(2)
1) TEST input must be EDM2 7
+
jumpered if not used.
+
Typically a Normally
OSSD1 8
Open switch held closed.
OSSD2 9
See Section 3.7.4 for
information on TEST
Single-Channel
input and hookup.
Safety Stop Circuit
(Not Used) 6
+24V dc 7
Reset
EDM1 6
PE 9
FSD
2
*
FSD
1
*
Dual-Channel
Safety Stop Circuit
* In
a
NOTE: Do not exceed OSSD maximum load capacitance specification.
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
!
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
!
* Arc Suppressors. See
manual for specific warnings.
WD012
EZ-SCREEN­® System (Type 4)
1-Channel EDM of IM-T-9A Interface Module
2-Channel EDM of IM-T-9A Interface Module
+24V dc
0V dc
+24V dc
0V dc
Receiver
PE 1
+24V dc 3
+24V dc 3
(Not Used) 4
(Not Used) 4
RESET 5
Reset
EDM2 7
EDM2 7
+
+
OSSD1 8
OSSD1 8
OSSD2 9
OSSD2 9
IM-T-9A
Terminal Locations
IM-T-9A
IM-T-9A
S4
3 3 9
S3
+ K2
9
K1
+
S1
S4
S2
S3
+ K2
Machine
Control
+
S1
S2
Y1
Y1
Y2
Y2
Y3
Y3
Y4
Y4
)-4!
K1
13
14
23
24
33
34
GLOSSARY
+
+
Reset
EDM1 6
EDM1 6
HOOKUP
DIAGRAMS
RESET 5
• EZ-SCREEN Grid
& Point
MPCE
2 *
MPCE
1 *
Machine
Control
13
14
23
24
33
34
MPCE
2 *
MPCE
1 *
9 Feedback (optional)
Feedback (optional)
9 3 3
1) See Section 3.5 for more
* Arc Suppressors.
Seeon Reset
information
manual for input
specific
and warnings.
hookup.
2) See Section 3.7.3 for
information on EDM
input and hookup.
!
Wiring
diagrams are
for information
only. across
* Installation
of transient
suppressors
1) See Section 3.5 for more
See appropriate
forMPCE2
all specific
the coils ofmanuals
MPCE1 and
is
information
* Arc Suppressors.
See on Reset
recommended
(seeinformation
Warning). for use.
warnings,
cautions and
input and
hookup.
manual for specific
warnings.
2) See Section 3.7.3 for
information on EDM
input and hookup.
More information online at
!
Wiring diagrams are for information only.
Installationmanuals
of transient
See *appropriate
for suppressors
all specific across
the coils
of MPCE1
and MPCE2for
is use.
warnings,
cautions
and information
recommended (see Warning).
bannerengineering.com
INTERNATIONAL
REPRESENTATIVES
Models
PE 1
dc Com 2
dc Com 2
Page 44
CONTACT/SWITCHING
DIAGRAMS
EZ-SCREEN
EZ-SCREEN
Receiver
iKNOW®
225
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD013
EZ-SCREEN­® AC Interface Box
EZAC-R9-QE8 – Hard-Wired with 3 NO and EDM
P4
2-ch. 1-ch.
Page 189
EDM
Models
X1
X2
X3
• EZAC-R9-QE8
1
1
X4
13
2
14
3
23
4
24
5
33
6
34
7
4
5
1
P5 2
8
P2
P1
2
P3 3
3
Connections
(Hard Wired)
1/2 NPT threads
for outputs
1/2 NPT threads
for AC inputs
L
EZAC-R9-QE8
N
100 - 230V ac
(Line) P5
3
(Neutral) P5
2
(Gnd) P5
1
Machine
Control
MPCE1
8-pin female
Euro-style QD
to emitter/receiver
K1
K2
*
13
14
23
24
MPCE2
33
34
*
2-Channel EDM Hookup
X1
2-ch. 1-ch.
(EDM1)
Monitoring Contacts
MPCE1
X2
X3
iKNOW®
(EDM2)
X1
2-ch. 1-ch.
(EDM1)
MPCE2
X4
1-Channel EDM Hookup
Monitoring Contacts
MPCE1
X2
MPCE2
CONTACT/SWITCHING
DIAGRAMS
X3
(EDM2)
X4
X1
2-ch. 1-ch.
(EDM1)
No EDM
X2
X3
X4
HOOKUP
DIAGRAMS
(EDM2)
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
INTERNATIONAL
REPRESENTATIVES
GLOSSARY
* Arc Suppressors. See manual for specific warnings.
!
226
More information online at
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD014
EZ-SCREEN­® AC Interface Box
EZAC-R11-QE8 – Hard-Wired with 2 NO, 1 NC and EDM
P4
2-ch. 1-ch.
EDM
Page 189
X1
Models
X2
X3
X4
• EZAC-R11-QE8
1
1
13
2
14
3
23
4
24
5
31
6
32
7
4
5
1
P5 2
8
P2
P1
2
P3 3
3
Connections
(Hard Wired)
L
EZAC-R11-QE8
1/2 NPT threads
for outputs
N
100 - 230V ac
(Line) P5
3
(Neutral) P5
2
(Gnd) P5
1
Machine
Control
MPCE1
K1
1/2 NPT threads
for AC inputs
8-pin female
Euro-style QD
to emitter/receiver
K2
*
13
14
23
24
MPCE2
31
32
*
2-Channel EDM Hookup
X1
2-ch. 1-ch.
(EDM1)
Monitoring Contacts
MPCE1
X2
X3
X1
2-ch. 1-ch.
(EDM1)
MPCE2
X4
1-Channel EDM Hookup
Monitoring Contacts
MPCE1
X2
iKNOW®
(EDM2)
MPCE2
X3
X1
2-ch. 1-ch.
(EDM1)
CONTACT/SWITCHING
DIAGRAMS
X4
No EDM
X2
X3
(EDM2)
X4
!
INTERNATIONAL
REPRESENTATIVES
GLOSSARY
* Arc Suppressors. See manual for specific warnings.
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
HOOKUP
DIAGRAMS
(EDM2)
More information online at
bannerengineering.com
227
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD015
EZ-SCREEN­® AC Interface Box
EZAC-R15A-QE8-QS83 – Mini-Style QD with 1 NO, 1 SPDT and 1-Channel EDM
L
EZAC-R15A-QE8-QS83
Page 189
(Neutral) P5
2
3
(Line) P5
3
2
(Gnd) P5
1
1
Bu
N
Bn
L
3-Pin Mini-Style Power Connector
Male Face View
Green/Yellow
wire
Brown
wire
Models
• EZAC-R15A-QE8-QS83
7
Connections
(8-Pin Mini)
K1
PINMALE
-INISTYLE
FOROUTPUTS
5
K2
1
14
13
24
23
4
8
32
31
6
PINMALE
-INISTYLE
FOR!#INPUTS
N
100 - 230V ac
PINFEMALE
%UROSTYLE1$
TOEMITTERRECEIVER
X1
3
(EDM1) X2
2
Blue
wire
Mating Cordset: QDS-3..C
Pin
Gn/Ye
Machine
Control
Color
Function
1
Green/Yellow
Gnd/PE
2
Brown
Line
3
Blue
Neutral
Gn/Ye
Bk
8-Pin Mini-Style Output Connector
Male Face View
MPCE1
N.O. (to load)
Green/Yellow
Bn
N.O.
Wh
N.O. (to load)
Orange
White
Violet
Mating Cordset: QDS-8..C
MPCE2
N.C. Aux (see Warning)
Bu
Black
Orange/Black
*
Vi
Blue
Brown
*
Lamp
N.O.
Or
+24V dc (switched)
Or/Bk
EDM
MPCE1
MPCE2
Pin
Color
Function
1
Brown
N.O.
2
Orange/Black
+24V dc (EDM)
3
Orange
EDM
4
White
N.O. (to load)
5
Black
N.O. (to load)
6
Blue
Common
7
Green/Yellow
Gnd/PE
8
Violet
N.C. Aux.
Monitoring Contacts
X3
(EDM2) X4
!
* Arc Suppressors. See manual for specific warnings.
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
WD016
EZ-SCREEN­® AC Interface Box
Page 189
Models
• EZAC-R8N-QE8-QS53
.EUTRAL0
,INE0
'ND0
+
GLOSSARY
+
8-pin female
Euro-style QD
to emitter/receiver
"U
.
"N
,
3-Pin Mini-Style Power Connector
Male Face View
Green/Yellow
wire
-0#% -0#%
Brown
wire
'N9E
Blue
wire
Mating Cordset: QDS-3..C
-ONITORING
#ONTACTS
Pin
-ACHINE
#ONTROL
Color
Function
1
Green/Yellow
Gnd/PE
2
Brown
Line
3
Blue
Neutral
'N9E
7H
./B
5-Pin Mini-Style Output Connector
Male Face View
-0#%
Black
"K
Blue
./A
White
Brown
Green/Yellow
Mating Cordset: QDS-5..C
3-pin male
Mini-style
for AC inputs
.
6AC
Connections
(5-Pin Mini)
5-pin male
Mini-style
for outputs
INTERNATIONAL
REPRESENTATIVES
,
%:!#2.1%13
HOOKUP
DIAGRAMS
CONTACT/SWITCHING
DIAGRAMS
iKNOW®
EZAC-R8N-QE8-QS53 – Mini-Style QD with 1 NO, 1 NC and Power Monitoring
"U
"N
.#B
Pin
Color
Function
-0#%
1
Black
N.O. (1a)
2
Blue
N.C. (2a)
3
Green/Yellow
Gnd/PE
4
Brown
N.C. (2b)
5
White
N.O. (1b)
.#A
8
%$- 8
8
%$- 8
* Arc Suppressors. See manual for specific warnings.
228
More information online at
!
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD017
EZ-SCREEN­® AC Interface Box
EZAC-R10N-QE8-QS53 – Mini-Style QD with 2 NO and Power Monitoring
L
EZAC-R10N-QE8-QS53
Page 189
Models
• EZAC-R10N-QE8-QS53
(Neutral) P5
2
3
(Line) P5
3
2
(Gnd) P5
1
1
3
Connections
(5-Pin Mini)
K1
5-pin male
Mini-style
for outputs
N
100 - 230V ac
5
K2
13
14
1
23
24
2
31
32
Bu
N
Bn
L
3-Pin Mini-Style Power Connector
Male Face View
Green/Yellow
wire
MPCE1 MPCE2
Brown
wire
Monitoring
Contacts
Gn/Ye
Pin
Machine
Control
3-pin male
Mini-style
for AC inputs
8-pin female
Euro-style QD
to emitter/receiver
Color
Function
1
Green/Yellow
Gnd/PE
2
Brown
Line
3
Blue
Neutral
Gn/Ye
Wh
5-Pin Mini-Style Output Connector
Male Face View
MPCE1
N.O. (1b)
Black
*
Bk
Bu
Blue
N.O. (1a)
Bn
White
Brown
Green/Yellow
Mating Cordset: QDS-5..C
MPCE2
N.O. (2b)
*
4
Blue
wire
Mating Cordset: QDS-3..C
N.O. (2a)
Pin
Color
Function
1
Black
N.O. (1a)
2
Blue
N.C. (2a)
3
Green/Yellow
Gnd/PE
4
Brown
N.C. (2b)
5
White
N.O. (1b)
X1
(EDM1) X2
X3
(EDM2) X4
* Arc Suppressors. See manual for specific warnings.
!
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
!
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
WD018
EZ-SCREEN­® AC Interface Box
CONTACT/SWITCHING
DIAGRAMS
iKNOW®
EZAC-E-QE.. – Hard-Wired Emitters with or without Test
Page 189
EZAC-E-QE8 or
EZAC-E-QE5
• EZAC-E-QE8
• EZAC-E-QE5
(Line) L
L
(Neutral) N
N
Connections
(Gnd)
5-Pin Euro
TEST function
available only
for model
EZAC-E-QE5
{
HOOKUP
DIAGRAMS
90-230V ac
TEST
TEST #1
TEST #2
GLOSSARY
Models
Terminal strip on box inside cover; see Figure 3
PIN
.04THREADS
%UROSTYLE1$
!#INPUTS
TOEMITTER
5-pin
1/2 NPT threads
Euro-style QD
AC inputs
to emitter
More information online at
bannerengineering.com
INTERNATIONAL
REPRESENTATIVES
8-Pin Euro
229
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD019
EZ-SCREEN­® AC Interface Box
EZAC-E-QE8-QS3 – Mini-Style QD Emitter
EZAC-E-QE5-QS5 – Mini-Style QD Emitter with Test
EZAC-E-QE5-QS5
EZAC-E-QE8-QS3
(Line) L
Brown
2
(Neutral) N
3
(Gnd)
1
Models
90-230V ac
Blue
Page 189
Brown
4
(Line) L
L
N
Green/Yellow
• EZAC-E-QE8-QS3
•EZAC-E-QE5-QS5
(Neutral) N
2
(Gnd)
3
TEST #1
1
TEST #2
5
Blue
Green/Yellow
L
90-230V ac
N
TEST
Black
White
Connections
3-Pin Mini-Style Power Connector
Male Face View
(3-Pin Mini)
5-Pin Mini-Style Output Connector
Male Face View
Blue
Brown
wire
Blue
wire
Pin
8-pin
Euro-style QD
to emitter
(5-Pin Mini)
5-pin male
Mini-style
AC inputs
Brown
Green/Yellow
Mating Cordset: QDS-3..C
3-pin male
Mini-style
AC inputs
White
Black
Green/Yellow
wire
Mating Cordset: QDS-5..C
Color
Function
Pin
Color
Function
1
Green/Yellow
Gnd/PE
1
Black
N.O. (1a)
2
Brown
Line
2
Blue
N.C. (2a)
3
Blue
Neutral
3
Green/Yellow
Gnd/PE
4
Brown
N.C. (2b)
5
White
N.O. (1b)
!
5-pin
Euro-style QD
to emitter
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
!
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
!
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
WD020
AG4-4E Laser Scanner
AG4-4E to FSD1 & FSD2
iKNOW®
+24V dc
AG4
Fuse
1.6A
1
CONTACT/SWITCHING
DIAGRAMS
0V dc
0V dc
Restart 2
(Reset)
Page 53
+24V dc
Models
FP1*
4
Alarm 1 5
• AG4-4E
(Auxiliary 1) **
FP2*
FP3*
X1
HOOKUP
DIAGRAMS
3
FP4*
+
6
7
8
9
10
OSSD1
OSSD2
11
13
GLOSSARY
FSD
1
12
Shield
FSD
2
14
Alarm 2 15
(Auxiliary 2) **
INTERNATIONAL
REPRESENTATIVES
* Figure shows Field Pair #1 selected. See
manual for further information on Zone
Pair Changeover.
** See manual for further information on
the non-safety Alarm/Auxiliary outputs.
Warning: Monitoring FSDs
230
FSDs must be monitored for proper
operation. 1-channel EDM can only be used
when the AG4-4E is configured for manual
reset. See manual.
More information online at
Single-Channel
Safety Stop
Circuit
Dual-Channel
Safety Stop
Circuit
NOTE: Do not exceed OSSD maximum load
capacitance specification.
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD021
AG4-4E Laser Scanner
AG4-4E to SC22-3
+24V dc
0V dc
AG4
0V dc
1
Restart 2
(Reset) ***
Page 53
+24V dc
Models
3
Fuse
1.6A
4
FP1*
Alarm 1 5
(Auxiliary 1) **
• AG4-4E
FP2*
FP3*
FP4*
X1
+24V dc
0V dc
6
PLC/Switching
Device to
Select Required
Field Pair
7
8
9
10
1
12
0V dc
Restart 2
13
(Reset)
14
S2
+24V dc
S3
FP1*
15
(Auxiliary 1) **
FP2*
* See manual*forSee
further
information
on Zone
Pair Changeover.
section
3.xx for further
information
Zone information
Pair Changeover
** See manual foronfurther
on the non-safety Auxiliary outputs.
*** The Manual **Reset
can for
be further
accomplished
by the SC22-3 or other
See function
section 3.xx
information
safety rated logic
device.
In this case
the AG4-4E is configured for
on the
non-safety
Alarm/Auxiliary
AG4
automatic Reset.
outputs.
X1
Restart 2
4
Alarm 1 5
(Auxiliary
1) **
AG4-4E
6
FP2*
OSSD1
3
FP1*
***
Laser Scanner
AG4-4E
7to UM Modules
FP3*
AG4
+24V dc
Page 53
FP1*
4
***
(Auxiliary 1) **
FP2*
• AG4-4E
FP3*
FP4*
X1
A1
***
OSSD2
8
***
11
S11
S13
A2
** See manual for further information on
the non-safety Alarm/Auxiliary outputs.
Machine
Control
Circuits
S23
6A max.
K1B 6 K2B
FP2*
7
FP3*
6A
8 max.
K2C
C
S14
PLC/Switching Device
FP2*
FP3*
FP4*
7
8
S23
6
FP2*
6A max.
7
K1CFP3* K2C
S33
FP4*
8
S14
MSC1
S24
*
+24V dc
PLC/Switching
MSC2
Device to
Select Required
*
Field Pair
S34
MSC3
0V dc must be
Note:
common with the AG4
MSC1
S24
S34
See WARNING
Below
MSC3
S34
*
*Arc suppressors
(see WARNING)
!
Note:
0V dc must be
common with the AG4
S11 (No Connection)
MSC Monitor
Contacts
or Jumper for No
Monitoring
MSC Monitor
Contacts
or Jumper for No
Monitoring
See WARNING
Below
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
MSC1 MSC2 MSC3
S33
More information
online at
S34
See WARNING
6A max.
K1C
K2C
MSC1 MSC2 MSC3
S33
UM Module Auto Reset
+24V dc
PLC/Switching
Device to
Select Required
Field Pair
6A max.
K1B
K2B
S11 (No Connection)
MSC Monitor
Contacts
or Jumper for No
Monitoring
Note:
0V dc must
* be
common with the AG4
FP4*
K1
S33
UM Module Auto Reset
4
6
4
FP1*
6A max.
K1B
K2B
6A max.
K1A
K2A
UM Module Au
*
*Arc suppressors
(see WARNING)
+24V dc
PLC/Switching
*
Device to
Select Required
MSC2
Field Pair
*** FP1 - FP4 See PLC/Switching device
hookup.
FP1*
Machine
Control
Circuits
S34 (No Connection)
6A max.
K1A 4 K2A
S13 FP1*
Alarm 2 15
(Auxiliary 2) **
S22 S34 S12
S34 (No Connection)
6A max.
K1A
K2A
S23
S33
S33
S12
Shield
Machine
Control
Circuits
PLC/Switching Device
PLC/Switching Device
* See manual for further information on
Zone Pair Changeover.
14 24 34 A2
S13
S11
*** FP1 - FP4 See PLC/Switching
device
Reset
hookup.
14
S21 S33 S11
Shield
14
* See manual for further information on
Zone Pair Changeover.
MSC1 MSC2
** See manual for further information
on MSC3
the non-safetyS11
Alarm/Auxiliary outputs.
Reset
*** FP1 - FP4 See PLC/Switching
device
hookup.
S11
S33
S12
Shield
** See manual for further information on
MSC1 MSC2 MSC3
the non-safety Alarm/Auxiliary outputs.
12
13
11
* See manual for further information on
Zone Pair Changeover.
10
OSSD1
0V dc
12
Alarm 2
(Auxiliary 2) **
S11
S12
***
***
13
11
12
Alarm 2 15
14
***
7
8
(Auxiliary 2) **A2
A1
UM-FA-9A15
6
9
UM-FA-..A
Terminal Locations
UM-FA..A
OSSD2
Alarm 1 5
Models
A1 13 23 33
OSSD1
Fuse
1.6 A
7
13
UM-FA-9A
***
10
3
OSSD2
Fuse
1.6 A
9
1
0V dc
Restart 2
(Reset)
8
FP4*
X1
+24V dc
A1
10
1
+24V dc
***
iKNOW®
WD022
FP3*
+24V dc
(Reset)
UM-FA-9A
6
Wiring diagrams are for
information only. See***
appropriate manuals***
for
FP4*
all specific warnings, cautions and
9
0V dc
information for use.
!
A1 A1 A2 A2
0V dc
Fuse
1.6 A
***
CONTACT/SWITCHING
DIAGRAMS
*** The Manual Reset function can be
accomplished by the SC22-3 or other
safety rated logic device. In this case the
AG4-4E is configured for Automatic
Reset.
4
Alarm 1 5
SC22-3
Safety Controller
(Auxiliary 2) **
3
HOOKUP
DIAGRAMS
Alarm 2
S1
GLOSSARY
OSSD2
+24V dc
AG4
11
INTERNATIONAL
REPRESENTATIVES
OSSD1
bannerengineering.com
231
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-MainBelow
Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD023
PICO-GUARD™ Controller
One PICO-GUARD System with 1-Channel EDM of IM-T-9A Interface Module
+24V dc
0V dc
PICO-GUARD
Controller
0V dc 20
21 +24V dc
23 System Reset
Safety Device
Contact Outputs
Page 59
Models
• SFCDT-4A1
• SFCDT-4A1C
1
USSl 1 Reset
2
a
3
b
4
c
5
d
Ch1* 33
Ch2* 34
Safety Device
Solid-State
Outputs
+V
IM-T-9A Terminal Locations
7
+
OV
Ch4* 36
Load
Aux 25
Load
Weak 26
Load
Fault 27
Load
* only for model
SFCDT-4A1C
a
8
b
9
c
EDM1a 12
USSl 2
Input
EDM1b 13
10 d
EDM2a 14
28 +V
EDM2b 15
30 Tx-
Remote
Interface
29 OVdc
RS-232
Diagnostics
Load
Load
USSl 1
Input
+
Load
Ch3* 35
+
+
OSSD1
31 Tx+
OSSD2
17
18
3 3 9
9
IM-T-9A
S4
S1
K2
S3
K1
S2
Y1
)-4!
Y2
Y3
Y4
9 Machine
Control
13
14
23
24
33
34
MPCE
2
MPCE
1
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
9 3 3
Feedback (optional)
WD024
PICO-GUARD™ Controller
iKNOW®
One PICO-GUARD System with 2-Channel EDM of IM-T-9A Interface Module
+24V dc
0V dc
PICO-GUARD
Controller
CONTACT/SWITCHING
DIAGRAMS
23 System Reset
Models
• SFCDT-4A1
• SFCDT-4A1C
IM-T-9A
Terminal Locations
2
USSl 1 Reset
a
3
b
4
c
5
d
USSl 1
Input
+
Safety Device
Solid-State
Outputs
Page 59
Safety Device
Contact Outputs
1
+V
7
+
OV
Load
Ch2* 34
Load
Ch3* 35
Load
Ch4* 36
Load
Aux 25
Load
Weak 26
Load
Fault 27
Load
8
b
9
c
EDM1a 12
EDM1b 13
USSl 2
Input
10 d
EDM2a 14
28 +V
EDM2b 15
29 OVdc
RS-232
Diagnostics
Ch1* 33
* only for model
SFCDT-4A1C
a
30 Tx-
Remote
Interface
HOOKUP
DIAGRAMS
0V dc 20
21 +24V dc
(2)
+
+
OSSD1
31 Tx+
OSSD2
17
18
GLOSSARY
3 3 9
(1)See
9Section 3.4.1 for
IM-T-9A
information on Reset input
and hookup.
S4
S3
(2) 2-Channel EDM shown. See
Section 3.9.3 for information
on EDM input and hookup.
S1
K2
K1
S2
Y1
Y2
)-4!
(3) Must meet External Stop
Device requirements.
See Section 3.7.
Y3
INTERNATIONAL
REPRESENTATIVES
Y4
9 Machine
Control
13
14
23
24
33
34
9 3 3
Feedback (optional)
232
More information online at
MPCE
2
MPCE
1
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD025
PICO-GUARD™ Controller
Two PICO-GUARD Systems with 2-Channel EDM
+24V dc
0V dc
PICO-GUARD
Page 59
Controller
0V dc 20
21 +24V dc
Models
1
USSl 1 Reset
2
a
3
b
4
c
5
d
7
a
USSl 1
Input
Safety Device
Solid-State
Outputs
+
+V
+
OV
8
b
9
c
Ch1* 33
Load
Ch2* 34
Load
Ch3* 35
Load
Ch4* 36
Load
Aux 25
Load
Weak 26
Load
Fault 27
Load
EDM2a 14
28 +V
EDM2b 15
Remote
Interface
30 Tx-
* only for model
SFCDT-4A1C
EDM1a 12
EDM1b 13
USSl 2
Input
10 d
29 OVdc
RS-232
Diagnostics
+
+
OSSD1
31 Tx+
OSSD2
17
18
PICO-GUARD
Controller
0V dc 20
23 System Reset
USSl 1 Reset
2
a
5
d
7
a
8
b
9
c
Load
Ch4* 36
Load
Aux 25
Load
Weak 26
Load
Fault 27
Load
EDM2a 14
28 +V
EDM2b 15
+
+
OSSD1 17
OSSD2 18
FSD 1
FSD 2
Single Channel
Safety Stop Circuit
Dual Channel
Safety Stop Circuit
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
INTERNATIONAL
REPRESENTATIVES
31 Tx+
Remote
Interface
30 Tx-
* only for model
SFCDT-4A1C
EDM1a 12
EDM1b 13
USSl 2
Input
10 d
29 OVdc
RS-232
Diagnostics
USSl 1
Input
Load
Ch3* 35
HOOKUP
DIAGRAMS
b
c
Load
Ch2* 34
GLOSSARY
3
4
Ch1* 33
CONTACT/SWITCHING
DIAGRAMS
1
iKNOW®
21 +24V dc
Safety Device
Contact Outputs
• SFCDT-4A1
• SFCDT-4A1C
Safety Device
Contact Outputs
23 System Reset
More information online at
bannerengineering.com
233
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD026
PICO-GUARD™ Controller
One PICO-GUARD System with 2-Channel EDM and 2 Generic FSDs
+24V dc
0V dc
PICO-GUARD
Controller
Page 59
0V dc 20
21 +24V dc
23 System Reset
Safety Device
Contact Outputs
Models
• SFCDT-4A1
• SFCDT-4A1C
1
USSl 1 Reset
2
a
3
b
4
c
5
d
7
a
USSl 1
Input
Safety Device
Solid-State
Outputs
+
+V
+
OV
8
b
9
c
Load
Ch2* 34
Load
Ch3* 35
Load
Ch4* 36
Load
Aux 25
Load
Weak 26
Load
Fault 27
Load
10 d
EDM2a 14
28 +V
EDM2b 15
Remote
Interface
30 Tx-
* only for model
SFCDT-4A1C
EDM1a 12
EDM1b 13
USSl 2
Input
29 OVdc
RS-232
Diagnostics
Ch1* 33
+
+
OSSD1
31 Tx+
OSSD2
17
18
FSD 1
FSD 2
Single Channel
Safety Stop Circuit
Dual Channel
Safety Stop Circuit
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
See Section 3.9 on interfacing of safety stop circuits
WD027
PICO-GUARD™ EXI/ATEX Controller
iKNOW®
Hazardous Environment Appication to Optical Elements
+24V
Intrinsically safe for:
Class I, Division 1, Groups A-D
Class I, Zone 0, Groups IIC
0V dc
PICO-GUARD Controller
GLOSSARY
HOOKUP
DIAGRAMS
CONTACT/SWITCHING
DIAGRAMS
I/O Terminals
21
Page 59
Models
23 System Reset
1
Unclassified or Class I, Division 2,
Groups A, B, C an D Hazardous
(Classified) Locations Class I,
Zone 2, Group IIC. For information
on compliance and classification
according to Directive 94/9/EC
(ATEX).
USSl 1 Reset
2
3
• SFCDT-4A1
• SFCDT-4A1C
Non-incendive for:
Class I, Division 2, Groups A, B, C & D
Class I, Zone 2, Group IIIC
20
4
Aux 25
USSl 1 Input
(+24V)
+5V
26
+5V
Fault 27
+5V
Weak
Load
Load
PICO-GUARD Models:
Optical Element Models:
SFCDT-4A1
SFCDT-4A1C
SFA-RS
SFI-R1L
SFI-S1L
SFI-A1
SFP12PSxx
SFP12PXPxx
SFP12PXTxx
SFI-M12SSxxUXT
Load
EDM1a 12
5
EDM1b 13
2
EDM2a 14
3
EDM2b 15
4
5
USSl 2 Input
(+24V)
OSSD1 17
OSSD2
18
SFA-FS
SFI-R1R
SFI-S1R
SFI-D1
SFP30SSxx
SFP30SXPxx
SFP30SXTxx
Note: “xx” is fiber optic cable length in feet.
+24V
+24V
FSD1
FSD1
Optical Elements
Optical Channels
(4 Emitter/Receiver Pairs)
(Fiber Optic Cable)
E1
R1
(Fiber Optic Cable)
E2
R2
INTERNATIONAL
REPRESENTATIVES
E3
R3
E4
R4
Installation must be in accordance with the National Electric Code
(NFPA 70, Article 504) and ANSI/ISA-RP12.6.
234
More information online at
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD028
PICO-GUARD™ Controller with Muting
One PICO-GUARD with Muting and 2-Channel EDM and 2 Generic FSDs
PICO-GUARD with Mute
+24V dc
0V dc
Controller
Model SFCDT-4A1CM1
0V dc 20
21 +24V dc
Page 59
Ch1 33
Load
Ch2 34
Load
Ch3 35
Load
Ch4 36
Load
Aux/Mute Lamp 25
Load
Mute Lamp 26
Load
Fault 27
Load
23 System Reset
Models
• SFCDT-4A1CM1
1
Mute Enable
2
a
3
b
4
a
5
b
7
a
8
b
9
a
MS1
MS2
MS3
EDM1a 12
EDM1b 13
MS4
10 b
EDM2a 14
EDM2b 15
28 +V
30 Tx-
Remote
Interface
29 OV dc
RS-232
Diagnostics
+
OSSD1 17
+
31 Tx+
OSSD2
NOTE: 2-Channel EDM shown.
See Primary Manual for
information on EDM input
and hookup.
FSD 1
FSD 2
18
Single-Channel
Safety Stop Circuit
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
Dual-Channel
Safety Stop Circuit
See Primary Manual for information on interfacing of safety stop circuits
WD029
SC22-3 Safety Controller
CONTACT/SWITCHING
DIAGRAMS
iKNOW®
1-Channel, 2-Channel and No EDM
1A
SO2
1B
2A
SO3
2B
3A
The figure shown is generic in nature and
represents all three EDM options:
Safety Stop
Circuit
FSD
3B
+24V dc
GLOSSARY
3A
• Safety Output SO1 is shown with NO EDM
configured (typically used with
self-monitored devices)
• Safety Output SO2 is shown with
Two-Channel EDM configured.
• Safety Output SO3 is shown with
One-Channel EDM configured.
• Any particular Safety Controller configuration
may use any combination of external device
monitoring options, depending on the
application.
FSD
2A
2B
+24V dc
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
FSD
1A
INTERNATIONAL
REPRESENTATIVES
See product manual for information on
external device monitoring and interfacing
safety circuits.
3B
HOOKUP
DIAGRAMS
SO1
• SC22-3
Dual-Channel
SC22
Single-Channel
Input Terminals
Models
Dual-Channel
Page 76
Single-Channel
Safety Stop
Circuit
1B
More information online at
bannerengineering.com
235
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD030
SC22-3 Safety Controller
1-Channel EDM to SC-IM9A
+24V dc
Page 76
Machine Control
Models
• SC22-3
SC-IM9A
Input Terminals
13
21
33
43
A1
14
22
34
44
A2
SC22
SO1
1A
SO2
1B
2A
SO3
2B
3A
3B
A2
Supplied
Terminal
Block
13
21
33
43
A1
14
22
34
44
A2
(To
(To
SO
SO
1A
)
1B
)
3 wires
iKNOW®
The SC-IM9A interface module depicted in this figure is shown in
one-channel EDM hookup. The SC-IM9B and SC-IM9C modules
are connected in the same manner, using individual one-channel
EDM circuits (terminals 21/22 on each pair of contacts).
*
MPCE
1
MPCE
2
See product manual for information on external device
monitoring and interfacing safety stop circuits.
*
MPCE
3
*
+24V dc
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
* Arc Suppressors. See manual for specific warnings.
INTERNATIONAL
REPRESENTATIVES
GLOSSARY
HOOKUP
DIAGRAMS
CONTACT/SWITCHING
DIAGRAMS
0V dc
236
More information online at
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD031
SC22-3 Safety Controller
1-Channel EDM to IM-TA-9A
Input Terminals
Page 76
SC22
SO1
1A
Models
SO2
1B
2A
SO3
2B
3A
3B
0V dc
A2
• SC22-3
IM-T-9A
S1
S3
K2
+24V dc
The IM-TA interface module depicted in this figure
is shown in one-channel EDM hookup. The IM-T-11A
module is connected in the same manner.
Depending on the application, each safety output
requires a separate and individually wired IM-T..A
module.
Machine
Control
See product manual for information on external device
monitoring and interfacing safety stop circuits.
K1
S4
S2
Y3
Y4
Y1
Y2
13
14
23
24
33
34
MPCE
1
*
MPCE
2
*
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
Feedback (optional)
!
* Installation of transient (arc) supressors across the coils of
MPCE1 and MPCE2 is recommended (see Warning)
* Arc Suppressors. See manual for specific warnings.
WD032
SC22-3 Safety Controller
CONTACT/SWITCHING
DIAGRAMS
iKNOW®
2-Channel EDM to IM-TA-9A
Input Terminals
Page 76
Models
SC22
SO1
1A
SO2
1B
2A
SO3
2B
3A
3B
0V dc
A2
HOOKUP
DIAGRAMS
• SC22-3
IM-T-9A
S1
S3
+24V dc
Depending on the application, each safety output
requires a separate and individually wired IM-T..A
module.
See product manual for information on external device
monitoring and interfacing safety stop circuits.
Machine
Control
S4
S2
Y3
Y4
Y1
Y2
13
14
23
24
33
34
MPCE
1
*
MPCE
2
*
* Installation of transient (arc) supressors across the coils of MPCE1 and MPCE2
is recommended (see Warning)
More information online at
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
Feedback (optional)
* Arc Suppressors. See manual for specific warnings.
GLOSSARY
The IM-TA interface module depicted in this figure
is shown in two-channel EDM hookup. The IM-T-11A
module is connected in the same manner.
K1
INTERNATIONAL
REPRESENTATIVES
K2
bannerengineering.com
237
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD033
GM-FA-10J Guard Monitoring Safety Module
GM-FA-10J 1-Channel Monitoring to Two 4-Wire Coded Magnetic Safety Switches
Mechanical stop
Guard #1
open
Blue
Gray
Black
Page 81
Brown
Models
S12
S11 S13
SI-MAG..SM
• GM-FA-10J
SI-MAG..MM
GM-FA-10J
Terminal Locations
Guard #2
open
S23 S21 S22
Blue
Gray
Black
-£Ó -££ -£Î
£ £Î
ÓÎ 9£
Brown
‡‡£ä
9Ó
£{
Ó{
NOTE: If only one magnetic safety
switch is used, select 1-channel
input and jumper S23 and S21.
SI-MAG..SM
SI-MAG..MM
Mechanical stop
NOTE: If only one magnetic safety switch is used, select
1-channel input and jumper S23 to S21.
Ó
Configured for one-channel monitoring of either one or two guards. This application is considered to meet or
exceed requirements for OSHA control reliability and Safety Category 3 and 4 per ISO 13849-1 (EN 954-1).
-ÓÎ -Ó£ -ÓÓ
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
WD034
GM-FA-10J Guard Monitoring Safety Module
CONTACT/SWITCHING
DIAGRAMS
iKNOW®
GM-FA-10J 2-Channel Monitoring to Two Positive-Opening Safety Interlock Switches
Page 81
Models
S12 S11 S13
Mechanical
stop
Guard #1
HOOKUP
DIAGRAMS
• GM-FA-10J
GM-FA-10J
Terminal Locations
S23 S21 S22
Mechanical
stop
GLOSSARY
-£Ó -££ -£Î
£ £Î
ÓÎ 9£
NOTE: Guard shown in closed position.
INTERNATIONAL
REPRESENTATIVES
‡‡£ä
9Ó
£{
Ó{
Ó
-ÓÎ -Ó£ -ÓÓ
238
Guard
open
Configured for two-channel monitoring of one guard. This application is considered to meet or exceed
requirements for OSHA control reliability and Safety Category 3 and 4 per ISO 13849-1 (EN 954-1).
More information online at
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD035
GM-FA-10J Guard Monitoring Safety Module
GM-FA-10J Alternate Wiring for 1-Channel Monitoring of Multiple Guards
Guard #1
Guard #2
Guard #n
SI-MAG..MM
SI-MAG..MM
SI-MAG..MM
SI-MAG..SM
SI-MAG..SM
SI-MAG..SM
Black
Brown
Blue
Gray
Black
Brown
Blue
Gray
Black
Brown
Blue
Gray
Mechanical stop
Page 81
Models
• GM-FA-10J
NOTE: Switch/magnet pairs
shown in closed position.
S12 S11 S13
GM-FA-10J
Terminal Locations
S23 S21 S22
-£Ó -££ -£Î
‡‡£ä
9Ó
£{
Ó{
Ó
Black
Brown
Blue
Gray
Black
Brown
Blue
Gray
Black
Brown
Mechanical stop
Blue
ÓÎ 9£
Gray
£ £Î
SI-MAG..SM
SI-MAG..SM
SI-MAG..SM
SI-MAG..MM
SI-MAG..MM
SI-MAG..MM
Guard #3
Guard #4
Guard #n+1
Configured for one-channel monitoring of multiple guards with single switches at each guard. Up to 10 Banner
magnetic switches may be connected to each channel in this series/parallel method. If other than Banner magnetic
switches are used, a total resistance of 270 ohms between S11/S13, S11/S12, S21/S22 and S21/S23 must not be
exceeded. Note: Not a Category 4 application per ISO 13849-1 (EN 954-1).
-ÓÎ -Ó£ -ÓÓ
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
WD036
GM-FA-10J Guard Monitoring Safety Module
Guard #2
Guard #3
Guard #4
Guard #n
CONTACT/SWITCHING
DIAGRAMS
Guard #1
iKNOW®
GM-FA-10J Alternate Wiring for 2-Channel Monitoring of Multiple Guards
Page 81
Models
GM-FA-10J
Terminal Locations
HOOKUP
DIAGRAMS
• GM-FA-10J
S12 S11 S13
NOTE: Guards shown in closed position.
£ £Î
GLOSSARY
-£Ó -££ -£Î
ÓÎ 9£
S23 S21 S22
9Ó
£{
Ó{
Ó
-ÓÎ -Ó£ -ÓÓ
Configured for two-channel monitoring of multiple guards with two safety switches mounted individually on each
guard. The number of mechanical switches is limited by the max. resistance of 270 ohm between S11-S13, S11-S12,
S21-S22 and S21-S23. The total resistance is calculated by adding the resistance of all guard switch contacts and the
resistance of the cables that connect the switches and the switches to the module.
Note: Not a Category 4 application per ISO 13849-1 (EN 954-1).
More information online at
INTERNATIONAL
REPRESENTATIVES
‡‡£ä
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
bannerengineering.com
239
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD037
GM-FA-10J Guard Monitoring Safety Module
GM-FA-10J to Guarded Machine
L1/+Vdc
MACHINE
CONTROL
24V ac/dc
Page 81
RESET
Models
S12 S11
A1
• GM-FA-10J
13
Y1
For Automatic
Reset, connect
directly and
configure DIP
switches
K1
GM-FA-10J
Terminal Locations
K2
Y2
-£Ó -££ -£Î
£ £Î
S13
23
14
24
A2
S23 S21 S22
ÓÎ 9£
OV ac/dc
‡‡£ä
MPCE2
*
* MPCE1
9Ó
£{
Ó{
MPCE2
Monitoring Contacts
or Jumper
MPCE1
Ó
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
L2/-V dc
-ÓÎ -Ó£ -ÓÓ
!
* Arc Suppressors. See manual for specific warnings.
INTERNATIONAL
REPRESENTATIVES
GLOSSARY
HOOKUP
DIAGRAMS
CONTACT/SWITCHING
DIAGRAMS
iKNOW®
* Arc Suppressor, see Warning
240
More information online at
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD038
ES-FA-..AA E-Stop Safety Module
ES-FA-..AA 1-Channel
Auto
AutoReset
Reset
Manual
ManualReset
Reset
+V +V
+V +V
dc common
dc common
dc common
dc common
24V24V
ac/dc
ac/dc
24V24V
ac/dc
ac/dc
Page 81
Models
E-Stop
E-Stop
Switch
Switch
• ES-FA-9AA
• ES-FA-11AA
Reset
Reset
MSC1
MSC1MSC3
MSC3
MSC
MSC
S11S11
S33S33
Monitor
Monitor
Contacts
Contacts
ES-FA-9AA
ES-FA-9AA
or or
S21S21
Jumper
Jumper
S34S34
3 3 3
S33S33
ES-FA-9AA
ES-FA-9AA
S11S11
S34S34(No(No
Connection)
Connection)
MSC2
MSC2
S22S22
S21S21
S12S12
6A max.
6A max.
L1/+V
L1/+V
dc dc
K1AK1A K2AK2A
14 14
13 13
3 3 3
6A max.
6A max.
L1/+V
L1/+V
dc dc
K1AK1A K2AK2A
13 13
MSC1
MSC1
14 14
MSC1
MSC1
24 24
MSC2
MSC2
34 34
MSC3
MSC3
!
3 3 3
6A max.
6A max.
Machine
Machine
Control
Control
Circuits
Circuits
6A max.
6A max.
K1BK1B K2BK2B
24 24
23 23
Machine
Machine
Control
Control
Circuits
Circuits
MSC2
MSC2
K1BK1B K2BK2B
23 23
6A max.
6A max.
6A max.
6A max.
K1CK1C K2CK2C
MSC3
MSC3
33 33
*
*
34 34
*
*
33 33
K1CK1C K2CK2C
iKNOW®
!
L2/-V
L2/-V
dc dc
Machine
Machine
Master
Master
Stop
Stop
Control
Control
Elements
Elements
L2/-V
L2/-V
dc dc
*Arc*Arc
suppressors
suppressors
(see(see
Warning
Warning
pagepage
362)362)
*Arc*Arc
suppressors
suppressors
(see(see
Warning
Warning
pagepage
362)362)
ES-FA-11AA
L1/+V dc
14
MSC1
23
24
MSC2
31
32
L2/-V dc
GLOSSARY
Machine
Control
Circuits
*
*
13
HOOKUP
DIAGRAMS
Machine
Master Stop
Control Elements
CONTACT/SWITCHING
DIAGRAMS
S12S12
*
*
Machine
Machine
Master
Master
Stop
Stop
Control
Control
Elements
Elements
%3&!!!
*
*
%3&!!!
S22S22
Feedback
(optional)
*Arc suppressors
(see Warning page 362)
!
* Arc Suppressors. See manual for specific warnings.
More information online at
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
bannerengineering.com
INTERNATIONAL
REPRESENTATIVES
! MSC1
MSC1
MSC2
MSC2
MSC3
MSC3
*
*
A2 A2
A1 A1
*
*
! A2 A2
A1 A1
ES-FA-..AA
Terminal Locations
3 3 3
E-Stop
E-Stop
Switch
Switch
241
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD039
ES-FA-..AA E-Stop Safety Module
ES-FA-..AA 2-Channel
Auto ResetAuto Reset
+V
+V
Manual Reset
Manual Reset
dc common
24V ac/dc
+V
dc common
+V
24V ac/dc
dc common
24V ac/dc
dc common
24V ac/dc
Page 81
Models
A1
• ES-FA-9AA
• ES-FA-11AA
E-Stop
Switch
A2
A1
A2
Reset
MSC1 MSC3
ES-FA-..AA
Terminal Locations
S11
S11
ES-FA-9AA
S33
ES-FA-9AA
S21
S21
S22
S22
S12
S12
S34
L1/+V dc
L1/+V dc
S21
L1/+V dc
E-Stop
Switch
S22
S22
S12
S12
L1/+V dc
6A max.
K1A
K2A
13
MSC1
13
K1A
K2A
14
MSC1 14
MSC1
24
23
6A max.
MSC2
33
34
iKNOW®
Machine
Control
Circuits
K1B
Machine
23 Control
Circuits
MSC3 34
6A max.
K2B
23
K1B
MSC3
6A max.
K2C
33
33
K1C
MSC2 24
MSC2
K2B
24
6A max.
K1C
K2C
*
33
MSC2 24
6A max.
K1C
K2C
6A max.
K2B
*
6A max.
K1B
K2B
*Arc suppressors *Arc suppressors
(see Warning page 362)
(see Warning page 362)
*
Machine
23 Control
Circuits
K2C
MSC3 34
34
MSC3
*
Machine
Control
Circuits
*
K1B
3 3 3
K1C
CONTACT/SWITCHING
DIAGRAMS
Machine
Machine
Master Stop
Master Stop
Control
Elements
Control Elements
6A max.
L2/-V dc
L2/-V dc
!
6A max.
*Arc suppressors *Arc suppressors
(see Warning page 362)
(see Warning page 362)
ES-FA-11AA
Machine
Master Stop
Control Elements
L1/+V dc
14
OPEN
L2/-V dc
Safety Gate or Guard with
end-of-travel stops and two
individually mounted
Safety Interlocking Switches
MSC1
E-Stop
24
31
32
MSC2
S11
GLOSSARY
E-Stop
*
23
Hookup Using Contacts from
Two Safety Switches
Series Connection of Multiple
E-Stop Switches
*
HOOKUP
DIAGRAMS
13
Machine
Control
Circuits
S21
S22
S12
Feedback
(optional)
S11
INTERNATIONAL
REPRESENTATIVES
S34 (No Connection)
(No Connection)
*
S21
ES-FA-9AA
*
S11
*
!
3 3 3
MSC1 14
S11
S34
K2A
14
13
S33
ES-FA-9AA
MSC2
*
K1A
K2A
13
S33
Machine
Machine
Master Stop
Master Stop
Control
Elements
Control Elements
6A max.
L2/-V dc
L2/-V dc
6A max.
K1A
A2
Reset
E-Stop
Switch
%3&!!!
A2
MSC1 MSC2 MSC3 MSC1 MSC2 MSC3
3 3 3
! A1
*
%3&!!!
MSC2
*
MSC1 MSC3
MSC
MSC
S33
Monitor
Monitor
Contacts
Contacts
or
or
Jumper
Jumper
S34
*
3 3 3
! A1
E-Stop
Switch
S21
S22
S12
*Arc suppressors
(see Warning page 362)
* Arc Suppressors. See manual for specific warnings.
242
More information online at
!
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD040
ES-..A-.5 E-Stop Safety Module
ES-..A-5A 1-Channel
Auto Reset
Auto Reset
S21
S21
S21
S21
S22
S22
S22
S22
MSC1 MSC3MSC1 MSC3
S34
S33
S34
MSC2 MSC4MSC2 MSC4
S33
3 3 3
! ! " "
3 3 3 3
S35
L1/+V dc
S35
6A max.
L1/+V dc
K1A
13
K2AK1A
13
%3!!
6A max.
23
9 9 9
9 Machine
Control
Circuits
MSC1
*
*
24
MSC2
MSC2
K2B
24
Machine
Control
6A max.
6A max.
Circuits K1
K2CK1C
K2C
C
33
33
34
*
*
MSC3
34
MSC3
6A max.
6A max.
*
*
43
44
MSC4
44
MSC4
*
*
K1D
43
Non-safety Non-safety
Auxiliary Monitor
Auxiliary51Monitor
Contact
Contact
K2DK1D
51
K2E
+V
A1
A1
A2
ES-UA-5A
ES-UA-5A
A2
B1
B2
ES-VA-5A
ES-VA-5A
B2
115V ac
B1
230V ac
A1
115V ac
230V ac
A2
B1
B2
ES-VA-5A
ES-VA-5A
B2
33
*
*
24
MSC2
MSC2
*
*
34
MSC3
34
MSC3
6A max.
6A max.
*
*
43
44
MSC4
44
MSC4
*
*
43
Non-safety Non-safety
Auxiliary Monitor
Auxiliary51Monitor
Contact
Contact
K2DK1D
51
Y32
12-24V dc
52
K2E
Y30
Y30
Y35Y32
Y35
Power
Outputs
SupplyPower Supply
Energized
Fault
Fault
12-24V dc
+V
6A max.
52
Y31
Outputs
Energized
K2D
6A max.K1E
K1E
Y31
Y35
12-24V dc
dc common dc common
+V
For power connection
For power connection
see Figure 4.
see Figure 4.
*
Arc Suppressors
* Arc Suppressors
(see WARNING(see
on page
WARNING
6) on page 6)
DC Power Connection
AC PowerAC Power
+V
115V ac or 230V
115V ac
ac or 230V ac
(depending (depending
on model) on model)
E-Stop
Switch
MSC1
K2B
24
23
K1D
Arc Suppressors
Arc Suppressors
* 1-Channel
E-Stop
Applications
(see1-Channel
(see
WARNING
on page
WARNING
6) onE-Stop
page
6) Applications
MSC1
14
6A max.
K2BK1B
K2E
*
K2A
14
Machine
Control
6A max.
6A max.
Circuits K1
K2CK1C
K2C
C
33
DC PowerDC Powerdc
dc
common
common
12-24V dc 12-24V dc
+V
E-Stop
Switch
12-24V dc 12-24V dc
B1
K2AK1A
13
23
Machine
Control
Circuits
Y30
dc
common
A1
A2
ES-UA-5A
ES-UA-5A
K1A
6A max.
dc common dc common
common
12-24V dc 12-24V dc
Machine
Machine
Master Stop Master Stop
Control Elements
Control Elements
6A max.
L2/-V dc
L2/-V dc
6A max.
L1/+V dc
K1B
AC Power Connection
+V
S35
100 mA max.
each Output
Y35Y32
For power connection
For power connection
2-Channel
2-Channel
E-Stop
E-Stop
Applications
Applications
see
Figure 4.
see Figure 4.
115 ac or 230V
115 ac
ac or 230V ac
(depending (depending
on model) on model)
S35
K2E
+V
DC PowerDC Powerdc
S32
Power
Outputs
SupplyPower Supply
Energized
Fault
Fault
12-24V dc
AC PowerAC Power
S32
13
52
Y30
100 mA max.
Non-safety
each
Output
Monitor Outputs
Non-safety
Monitor Outputs
Y32
6A max.
52
Y31
Outputs
Energized
K2D
6A max.K1E
K1E
Y31
+V
MSC1
14
6A max.
K2BK1B
23
L1/+V dc
K2A
14
K1B
Machine
Machine
Master Stop Master Stop
Control Elements
Control Elements
6A max.
L2/-V dc
L2/-V dc
S33
Jumper
Non-safety
Monitor Outputs
3 3 3
S32
Jumper
MSC2 MSC4MSC2 MSC4
GLOSSARY
S32
Jumper
S34
S33
Jumper
S31
MSC MonitorMSC Monitor
S12
Contacts
Contacts
or Jumper foror Jumper for
No Monitoring
No Monitoring
S32
S32
S12
A1
A1
A2
ES-UA-5A
ES-UA-5A
A2
B1
B2
ES-VA-5A
ES-VA-5A
B2
115V ac
12-24V dc 12-24V dc
B1
230V ac
E-Stop
Switch
E-Stop
Switch
A1
115V ac
230V ac
iKNOW®
S34
Reset SwitchReset Switch
CONTACT/SWITCHING
DIAGRAMS
ES-..A-5A
Terminal Locations
S31
MSC MonitorMSC Monitor
S12
Contacts
Contacts
or Jumper foror Jumper for
No Monitoring
No Monitoring
S32
S32
S12
MSC1 MSC3MSC1 MSC3
S31
HOOKUP
DIAGRAMS
S31
A1
A2
ES-UA-5A
ES-UA-5A
A2
B1
B2
ES-VA-5A
ES-VA-5A
B2
12-24V dc 12-24V dc
B1
12-24V dc 12-24V dc
INTERNATIONAL
REPRESENTATIVES
• ES-UA-5A
• ES-VA-5A
ES-UA-5A ES-UA-5A
12-24V dc/115V
12-24V
ac dc/115V ac
ES-VA-5A
ES-VA-5A
S11
S11
12-24V dc/230V
12-24V
ac dc/230V ac
100 mA max.
each Output
Models
ES-UA-5A ES-UA-5A
12-24V dc/115V
12-24V
ac dc/115V ac
ES-VA-5A
ES-VA-5A
S11
S11
12-24V dc/230V
12-24V
ac dc/230V ac
100 mA max.
Non-safety
each
Output
Monitor Outputs
Page 81
Manual
Manual
ResetReset
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
* Arc Suppressors. See manual for specific warnings.
More information online at
bannerengineering.com
243
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD041
ES-..A-.5 E-Stop Safety Module
ES-..A-5A 2-Channel
Auto Reset
Auto Reset
Manual
ResetReset
Manual
E-Stop Switch
E-Stop Switch
E-Stop Switch
E-Stop Switch
ES-UA-5A ES-UA-5A
12-24V dc/115V
ac dc/115V ac
12-24V
ES-VA-5A
S11
ES-VA-5A
S11
12-24V dc/230V
ac dc/230V ac
12-24V
S21
S22
• ES-UA-5A
• ES-VA-5A
MSC1 MSC3
MSC1 MSC3
S22
S31
S34
S33
S22
Reset SwitchReset Switch
S32
S35
3 3 3
! ! " "
3 3 3 L1/+V
dc
3 3 3 3
S35
6A max.
L1/+V dc
K1A
13
6A max.
23
9 9 9
9 14
Machine
Control
Circuits
24
6A max.
K1C
33
6A max.
K2K1
D
D
6A max.
K1
E
51
K2E
Y31
Y32
MSC3
*
*
MSC4
44
MSC4
*
*
52
52
K2E
Y30
Y30
Y35
Y32
Machine
Control
Circuits
Machine
Control
Circuits
6A max.
6A max.
HOOKUP
DIAGRAMS
Series Connection of Multiple
E-Stop Switches
MSC2
*
*
MSC3
34
MSC3
*
*
MSC4
44
MSC4
*
*
6A max.
K2K1
D
D
K2D
44
43
6A max.
K1
K1E
6A max.
E
51
K2E
Y31
Y32
Y35
*
MSC2
24
K2C
34
K1D
Y31
*
6A max.
K2K1
C
C
33
Non-safety Non-safety
Auxiliary Monitor
Auxiliary51Monitor
Contact
Contact
MSC1
K2B
24
K1C
43
MSC1
14
6A max.
K2K1
B
B
23
33
52
52
K2E
Y30
Y30
L2/-V dc
Y35
Y32
Y35
Outputs Power
Supply
Outputs
Power Supply
Energized Energized
Fault
Fault
12-24V dc 12-24V dc
dc common dc common
+V
K2A
14
6A max.
23
L2/-V dc
6A max.
K2K1
A
A
13
12-24V dc 12-24V dc
Hookup Using Contacts from
Two Safety
Suppressors
* ArcSwitches
For power connection
+V
2-Channel
E-Stop Applications
2-Channel
E-Stop Applications
AC Power
(see WARNING
below)
WARNING below)
(see
see Figure see
4. Figure 4.
AC Power
DC Power
A1
+V
+V
115 ac or 230V ac115 ac or 230V ac
(depending on model)
(depending on model)
12-24V dc
dc
common
common
12-24V dc
ES-UA-5A
A2
ES-UA-5A
A2
A1
ES-UA-5A
A2
ES-UA-5A
A2
12-24V dc
12-24V dc
B1
ES-VA-5A
B1
B2
ES-VA-5A
B2
B1
ES-VA-5A
B1
B2
ES-VA-5A
B2
230V ac
115V ac
230V ac
A1
DC Power
dc
A1
115V ac
GLOSSARY
1-Ch
1-Channel
E-
DC Power Connection
* Arc Suppressors
For power connection
* Arc Suppressors
For power connection
Suppressors
* Arcbelow)
For power connection
(see WARNING
(see WARNING below)
see Figure see
4.OPEN
Figure 4.
E-Stop
dc common dc common
+V
AC Power Connection
Safety Gate or Guard with
end-of-travel stops and two
individually mounted
Safety Interlocking Switches
E-Stop
12-24V dc
E-Stop
Switch
E-Stop
Switch
A1
S21
S22
A2
ES-UA
B1
B2
ES-VA
ES-VA-5A
230V ac
115V
230V
S12
S11
S21
S22
S12
* Arc Suppressors. See manual for specific warnings.
244
A1
ES-UA-5A
115V ac
12-24V dc
NOTE: B2 terminal (dc common) is also the
earthing terminal for the ac supply.
AC Powe
AC Power
115V ac o
115V ac or 230V ac
(depending
(depending on model)
B1
S11
INTERNATIONAL
REPRESENTATIVES
S35
K1A
K1B
Outputs Power
Supply
Outputs
Power Supply
Energized Energized
Fault
Fault
+V
Machine Machine
Master Stop Master Stop
Control Elements
Control Elements
6A max.
L1/+V dc
13
*
MSC3
34
S32
S35
L1/+V dc
100 mA max.
each Output
100 mA max.
Non-safety
each Output
Monitor Outputs
CONTACT/SWITCHING
DIAGRAMS
Non-safety
Monitor Outputs
Y31
6A max.
L2/-V dc
MSC2
K2D
44
K1E
*
*
34
43
Non-safety Non-safety
Auxiliary Monitor
Auxiliary51Monitor
Contact
Contact
*
K2C
33
43
MSC1
MSC2
24
6A max.
K2K1
C
C
6A max.
MSC1
14
K2B
23
K1D
iKNOW®
6A max.
K2K1
B
B
K1B
Machine
Control
Circuits
K2A
13
%3!!
L2/-V dc
6A max.
K2K1
A
A
S31
S33
S32
Machine Machine
Master Stop Master Stop
Control Elements
Control Elements
Jumper
S31
Jumper
Non-safety
Monitor Outputs
S32
S12
S33
S33
MSC1 MSC3
MSC1 MSC3
S22
MSC MonitorMSC Monitor
S12Contacts Contacts
or Jumper for
or Jumper for
No Monitoring
S32
No Monitoring
S32
S34
MSC2 MSC4
MSC2 MSC4
S34
Jumper
Jumper
S21
S31
MSC MonitorMSC Monitor
Contacts Contacts
S12
or Jumper for
or Jumper for
No Monitoring
S32
No Monitoring
S32
S34
MSC2 MSC4
MSC2 MSC4
S12
ES-..A-5A
Terminal Locations
S21
S21
100 mA max.
each Output
Models
ES-UA-5A ES-UA-5A
12-24V dc/115V
ac dc/115V ac
12-24V
ES-VA-5A
ES-VA-5A
S11
12-24V dc/230V
ac dc/230V ac
12-24V
100 mA max.
Non-safety
each Output
Monitor Outputs
Page 81
S11
More information online at
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD042
ES-TN-1H.. E-Stop Safety Module
ES-TN-1H.. 2-Channel
+V
dc common
24V dc
A2
A1
Page 81
Emergency Stop Switch
Models
• ES-TN-1H1
• ES-TN-1H2
• ES-TN-1H3
• ES-TN-1H4
• ES-TN-1H5
• ES-TN-1H6
• ES-TN-1H7
• ES-TN-1H8
• ES-TN-1H9
• ES-TN-1H10
• ES-TN-1H11
• ES-TN-1H12
X1
S11
Note: Jumper on
S21-S22 for
1-channel E-Stop
Reset Switch
S21
X3
S22
X4
S12
X5
Y1
X6
Cancel Delay Input
Y2
L1/+V dc
ES-TN-1H..
Terminal Locations
Note: Jumper on
X1-X2 for Auto-reset.
X2
K1A
MSC-Monitor
Contacts
MSC3
Note: Jumper on X3-X4
and/or X5-X6
if no feedback contacts
are monitored
MSC2
MSC-Monitor
Contacts
MSC4
Machine Master
Stop Control
Elements L2/-V dc
4A max.
K2A
13
MSC1
14
MSC1
Immediate
*
4A max.
£ -££ -£Ó
8£ 8Ó £Î £{
8Î 8{
x£
xÓ
ÓÎ Ó{
Machine
Control
Circuits
K1B
K2B
23
24
MSC2
Immediate
Series Connection of Multiple
E-Stop Switches
*
4A max.
K3A
-‡/ ‡£°°
K4A
37
38
MSC3
Delayed
În È£ ÈÓ
8x 8È
{Ç
{n 9£
*
4A max.
9Ó
K3B
-Ó£ -ÓÓ Ó
E-Stop
E-Stop
K4B
47
48
MSC4
*
K1C
K2C
S11
52
K3C
K4C
S22
S12
Jumper between S21 and
S22, if 1-channel E-Stop is
selected.
Immediate
61
S21
CONTACT/SWITCHING
DIAGRAMS
51
Non-safety Auxiliary
Monitor Contacts
62
Delayed
iKNOW®
Delayed
Hookup Using Contacts from
Two Safety Switches
GLOSSARY
Safety Gate or Guard with
end-of-travel stops and two
individually mounted
Safety Interlocking Switches
HOOKUP
DIAGRAMS
OPEN
S11
!
* Arc Suppressors. See manual for specific warnings.
More information online at
S21
S22
S12
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
bannerengineering.com
INTERNATIONAL
REPRESENTATIVES
ÎÇ
245
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD043
ES-TN-14.. E-Stop Safety Module
ES-TN-14H.. 2-Channel
+V
dc common
24V dc
A1
Page 81
Models
Emergency Stop Switch
A2
X1
S11
Note: Jumper on
S21-S22 for
1-channel E-Stop
• ES-TN-14H5
• ES-TN-14H6
ES-TN-14H5
ES-TN-14H6
Reset Switch
S21
X3
S22
ES-TN-14H.
Terminal Locations
X4
S12
X5
Y1
X6
Cancel Delay Input
Y2
£ -££ -£Ó
8£ 8Ó £Î £{
™Ó
ÓÎ Ó{
ÎÎ
Î{
K1A
{Î {{
K2A
13
MSC1
MSC-Monitor
Contacts
MSC3
Note: Jumper on X3-X4
and/or X5-X6
if no feedback contacts
are monitored
MSC2
MSC-Monitor
Contacts
MSC4
Machine Master
Stop Control
Elements L2/-V dc
4A max.
L1/+V dc
8Î 8{
™£
Note: Jumper on
X1-X2 for Auto-reset.
X2
14
MSC1
Immediate
-‡/ ‡£{°°
xÇ
xn ÈÇ Èn
8x 8È ÇÇ
Çn ä£
äÓ
*
4A max.
nÇ
nn 9£
Machine
Control
Circuits
9Ó
-Ó£ -ÓÓ Ó
K1B
K2B
23
24
MSC2
Immediate
4A max.
K1C
*
K2C
33
Series Connection of Multiple
E-Stop Switches
34
Immediate
4A max.
K1D
K2D
43
44
Immediate
E-Stop
E-Stop
4A max.
K3A
K4A
iKNOW®
57
58
MSC3
Delayed
*
4A max.
K3B
67
CONTACT/SWITCHING
DIAGRAMS
S11
K4B
68
MSC4
K3C
*
K4C
77
Hookup Using Contacts from
Two Safety Switches
4A max.
K3D
K4D
87
88
HOOKUP
DIAGRAMS
Delayed
OPEN
Safety Gate or Guard with
end-of-travel stops and two
individually mounted
Safety Interlocking Switches
K1E
91
S12
78
Delayed
Non-safety Auxiliary
Monitor Contacts
S22
Jumper between S21 and
S22, if 1-channel E-Stop is
selected.
Delayed
4A max.
S21
K2E
92
Immediate
K3E
GLOSSARY
01
K4E
02
Delayed
INTERNATIONAL
REPRESENTATIVES
S11
* Arc Suppressors. See manual for specific warnings.
246
More information online at
!
S21
S22
S12
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD044
ES-FA-6G E-Stop Safety Module
ES-FA-6G 1-Channel
+V
dc common
24V ac/dc
Page 81
Models
E-Stop
Switch
• ES-FA-6G
A2
A1
ES-FA-6G
Terminal Locations
ES-FA-6G
Reset
Reset
Switch
(jumper for auto reset)
and no monitoring
Y1
£Î ÓÎ ÎÎ
Y2
£ 9£ 9Ó
-‡‡È
MSC1 MSC2 MSC3
MSC Monitor Contacts
Machine
Master Stop
Control Elements
6A max.
L1/+V dc
K1A
{£ {Ó Ó
L2/-V dc
K2A
13
14
MSC1
24
MSC2
34
MSC3
*
£{ Ó{ Î{
6A max.
23
K1C
6A max.
K2C
*
33
iKNOW®
Machine
Control
Circuits
*
K2B
K1B
K2D
42
E-Stop
HOOKUP
DIAGRAMS
Series Connection of Multiple
E-Stop Switches
E-Stop
+24V ac/dc
A1
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
* Arc Suppressors. See manual for specific warnings.
More information online at
bannerengineering.com
GLOSSARY
Non-safety
Auxiliary
Monitor Contact
6A Max.
INTERNATIONAL
REPRESENTATIVES
41
CONTACT/SWITCHING
DIAGRAMS
K1D
247
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD045
UM-A... Universal Safety Module
UM-FA-..A Hard Contact, 2-Channel
Auto Reset
Manual
Manual Reset
Reset
+24V ac/dc
+24V ac/dc
0V
0V
Page 89
Models
UM-FA-..A
UM-FA-..A
• UM-FA-9A
• UM-FA-11A
UM-FA-..A
Terminal Locations
A2
A1
A2
A1
Reset
E-Stop
Switch
MSC1 MSC2 MSC3
MSC1 MSC3
S11
S33
S21 S33 S11
S21
A1 13 23 33
S34
S22
UM-FA..A
MSC2
S33
MSC
Monitor
Contacts
or
Jumper
S11
S34
E-Stop
Switch
See Interfacing MSCs
WARNING
(No Connection)
S21
S22
S12
S12
14 24 34 A2
S22 S34 S12
Machine
Master Stop
Control Elements
7A max.
L1
iKNOW®
K1A
K2A
14
7A max.
K1B
7A max.
L1
K1A
23
24
MSC2
32
*Arc suppressors
(see WARNING)
K2A
13
MSC1
K2B
Machine
Master Stop
Control Elements
14
MSC1
24
MSC2
32
*Arc suppressors
(see WARNING)
7A max.
Machine
Control
Circuits
K1B
L2
K2B
23
*
*
CONTACT/SWITCHING
DIAGRAMS
Machine
Control
Circuits
L2
*
13
UM-FA-11A Machine Connection
*
UM-FA-9A Machine Connection
7A max.
7A max.
31
K1C
31
K1C
K2C
HOOKUP
DIAGRAMS
K2C
Two Safety Switches
GLOSSARY
Safety Interlock
Switch #1
Multiple E-stops
Safety gate
or guard
Safety Interlock
Switch #2
INTERNATIONAL
REPRESENTATIVES
S11
S11
S21
S22
S12
* Arc Suppressors. See manual for specific warnings.
248
More information online at
S21
S22
S12
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD046
UM-FA-..A Universal Safety Module
UM-FA-..A Hard Contact, 1-Channel
Auto
AutoReset
Reset
Manual
Reset
Manual Reset
+24V ac/dc
0V
+24V ac/dc
0V
Page 89
Models
E-Stop
Switch
• UM-FA-9A
• UM-FA-11A
E-Stop
Switch
UM-FA-..A
A2
A1
A2
A1
UM-FA-..A
UM-FA-..A
Terminal Locations
Reset
MSC1 MSC3
S11
S33
S21 S33 S11
S21
A1 13 23 33
S34
S22
UM-FA..A
MSC2
MSC1 MSC2 MSC3
S33
MSC
Monitor
Contacts
or
Jumper
S11
S34
(No Connection)
S21
See Interfacing MSCs
WARNING
S22
S12
S12
14 24 34 A2
S22 S34 S12
K2A
14
7A max.
K1B
Machine
Control
Circuits
7A max.
L1
K1A
14
MSC1
24
MSC2
32
*Arc suppressors
(see WARNING)
7A max.
K2B
Machine
Control
Circuits
24
MSC2
32
*Arc suppressors
(see WARNING)
K1B
L2
K2B
23
*
*
23
K2A
13
MSC1
*
13
L2
*
K1A
Machine
Master Stop
Control Elements
iKNOW®
Machine
Master Stop
Control Elements
7A max.
L1
UM-FA-11A Machine Connection
CONTACT/SWITCHING
DIAGRAMS
UM-FA-9A Machine Connection
7A max.
7A max.
31
K1C
31
K1C
K2C
HOOKUP
DIAGRAMS
K2C
Two Safety Switches
Safety Interlock
Switch #1
Multiple E-stops
GLOSSARY
Safety gate
or guard
Safety Interlock
Switch #2
S11
S21
S22
S21
S22
S12
INTERNATIONAL
REPRESENTATIVES
S11
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
S12
!
* Arc Suppressors. See manual for specific warnings.
More information online at
bannerengineering.com
249
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD047
UM-FA-..A Universal Safety Module
UM-FA-..A Solid-State, 2 channel
Auto Reset
Auto Reset
Manual
Reset
Manual
Reset
+24V dc
+24V dc
0V dc
0V dc
Page 89
Models
UM-FA-..A
• UM-FA-9A
• UM-FA-11A
UM-FA-..A
A2
A1
A2
A1
MSC1 MSC2 MSC3
S33
UM-FA-..A
Terminal Locations
MSC1 MSC2 MSC3
0V
+24V dc
0V dc* (dc common)
S21 S33 S11
+
A1 13 23 33
+
S33
S11
S21
S34
MSC
Monitor
Contacts
or
Jumper
+24V dc
S22
+24V dc
S12
Reset
MSC+24V dc
Monitor
Contacts
or
Jumper
+
0V
S11
0V dc* (dc common)
S21
S34
(No
(No
Connection)
Connection)
+24V dc
S22
+24V dc
+
S12
UM-FA..A
* S21 must be connected to 24V dc
output common in 24V ac supply applications.
* S21 must be connected to 24V dc output common only in 24V ac supply applications.
14 24 34 A2
S22 S34 S12
Machine
Master Stop
Control Elements
7A max.
L1
K1A
K2A
14
7A max.
K1B
7A max.
L1
K1A
23
24
MSC2
32
*Arc suppressors
(see WARNING)
K2A
13
MSC1
K2B
Machine
Master Stop
Control Elements
14
MSC1
24
MSC2
32
*Arc suppressors
(see WARNING)
7A max.
Machine
Control
Circuits
K1B
L2
K2B
23
*
*
CONTACT/SWITCHING
DIAGRAMS
Machine
Control
Circuits
L2
*
iKNOW®
13
UM-FA-11A Machine Connection
*
UM-FA-9A Machine Connection
7A max.
7A max.
31
K1C
31
K2C
HOOKUP
DIAGRAMS
K2C
Two Safety Switches
Safety Interlock
Switch #1
GLOSSARY
K1C
Multiple E-stops
Safety gate
or guard
Safety Interlock
Switch #2
INTERNATIONAL
REPRESENTATIVES
S11
S11
250
S21
More information online at
S22
S12
S21
S22
S12
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD048
SM-..A-5A Safety Mat Monitoring Module
SM-..A-5A to 4-Wire Safety Mat
+V
24V dc
or
115V ac or 230V ac
(depending on model)
Page 91
dc common
Models
A2
A1
• SM-GA-5A
• SM-HA-5A
B2
B1
SM-GA-5A
S11
for 24/115V
S12
SM-HA-5A
Mat
SM-..A-5A
Terminal Locations
for 24/230V
MSC1 MSC3
S31
MSC
Monitor
Contacts
or Jumper
S22
Reset
Switch
3 3 3
! ! "
"
S32
S21
MSC2 MSC4
3 3 3
S34
3 3 3 3
S33
Machine
Master Stop
Control Elements
S32
Jumper for Auto Reset
S35
9 6A max.
K1A
L2/-V dc
K2A
13
14
MSC1
24
MSC2
34
MSC3
44
MSC4
6A max.
K1B
K2B
Machine
Control
Circuits
*
23
6A max.
K1C
K2C
*
33
6A max.
K1D
iKNOW®
K2D
43
51
*
6A max.
K2E
K1E
CONTACT/SWITCHING
DIAGRAMS
9 9 9
*
52
Non-safety
Auxiliary
Monitor Contact
Y31
20 mA max.
each Output
Non-safety
Monitor Outputs
S11
Y32
Outputs
Energized
24V dc
+V
Series Connection of Multiple
E-Stop Switches
Y30
Mat #1
Y35
Mat #n
HOOKUP
DIAGRAMS
L1/+V dc
S12
Power Supply
Fault
S22
dc common
S21
INTERNATIONAL
REPRESENTATIVES
NOTE: The number of mats
is limited by the total series
resistance per input channel.
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
* Arc Suppressors. See manual for specific warnings.
More information online at
bannerengineering.com
GLOSSARY
3-!!
251
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD049
MM-TA-12B and MM2-TA-12B Muting Modules
2 FSDs, 2-Channel EDM, Mute Enable
0V dc
24V dc
Brown
Grn/Yel
Page 94
Models
1
• MM-TA-12B
• MM2-TA-12B
7
2
Black
5
8
3
Blue
6
FSD1
White
4
FSD2
Violet
Mute
Orange
Enable
Org/Blk
Single-Channel
Safety Stop Circuit
Dual-Channel
Safety Stop Circuit
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
Installation of transient (arc) suppressors across the
coils of FSD1 and FSD2 is recommended (see
Warning).
WD050
MM-TA-12B and MM2-TA-12B Muting Modules
iKNOW®
Generic Hookup, 2-Channel EDM, Mute enabled to IM-TA-..A
0V dc
CONTACT/SWITCHING
DIAGRAMS
24V dc
Brown
Grn/Yel
Page 94
Models
• MM-TA-12B
• MM2-TA-12B
1
7
2
5
8
HOOKUP
DIAGRAMS
3
Blue
6
4
Black
White
Violet
Mute
Enable
Orange
IM-T-9A
Org/Blk
S4
GLOSSARY
Machine
INTERNATIONAL
REPRESENTATIVES
S1
K2
Control
Installation of transient (arc) suppressors across the
coils of MPCE1 and MPCE2 is recommended.
K1
S3
S2
Y1
Y2
Y3
Y4
13
14
23
24
33
34
MPCE
1
MPCE
2
Feedback (optional)
Installation of transient (arc) suppressors across the coils of MPCE1 and
MPCE2 is recommended (see Warning).
252
More information online at
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD051
MMD-TA-12B DIN-Rail Muting Module
Solid-State Output, 2 FSDs and 2-Channel EDM
+24V dc
0V dc
MMD-TA-12B
A1
A2
Page 94
Models
Y1
EDM1
• MMD-TA-12B
Y2
Y3
EDM2
MMD-TA-12B
Terminal Locations
Y4
+
OSSD1
! 8 8
: - :
3 3 3 3
8 8 8
8
9
: - :
0V
Y6
0V
Y7
FSD1
: - :
8 8 8 8
Installation of transient (arc)
suppressors across the coils of
FSD1 and FSD2 is
recommended (see Warning).
--$4!"
9 9 9
Y5
8 8 : :
9 9 9 9
: - :
: 8 !
OSSD2
+
Y8
FSD2
Single-Channel
Safety Stop Circuit
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
Dual-Channel
Safety Stop Circuit
NOTE: Do not exceed OSSD maximum load
capacitance specifications.
WD052
MMD-TA-11B DIN-Rail Muting Module
iKNOW®
Relay Outputs
1-Channel EDM
+24V dc
Page 94
0V dc
A1
MMD-TA-11B
+24V dc
A2
CONTACT/SWITCHING
DIAGRAMS
2-Channel EDM
0V dc
A1
MMD-TA-11B
A2
Models
MMD-TA-11B
Terminal Locations
Y1
Y1
EDM1
EDM1
Y2
Y2
Y3
Y3
EDM2
EDM2
Y4
L1
S11 S12 S21 S22
X5 X6 X7
X8
Y4
Z12 M2 Z22
K1A
X9 X10 X11 X12
Machine
Control
Circuits
MMD-TA-11B
13
K1B
L2
K2A
K2B
14
23
24
31
32
K1C
MPCE1
MPCE2
L1
K1A
Machine
Control
Circuits
13
Y4
Z23 M3 Z13
X3 X4
31
32
Z14 M4 Z24
13 14
23
14
K2B
23
24
31
32
K2C
Y1 Y2 Y3
K1B
L2
K2A
K1C
GLOSSARY
Z21 M1 Z11
MPCE1
MPCE2
K2C
24
Z13 X14 A2
INTERNATIONAL
REPRESENTATIVES
A1 X1 X2
HOOKUP
DIAGRAMS
• MMD-TA-11B
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
Installation of transient (arc) suppressors
recommended across MPCE1 and MPCE2.
More information online at
bannerengineering.com
253
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD053
MMD-TA-12B DIN-Rail Muting Module
2-Channel EDM with Interface Model
0V dc
+24V dc
A1
MMD-TA-12B
A2
Page 94
Models
Y1
• MMD-TA-12B
EDM1
Y2
MMD-TA-12B
Terminal Locations
Y3
EDM2
Y4
+
! 8 8
: - :
3 3 3 3
8 8 8
8
OSSD1
: - :
8 8 8 8
--$4!"
OSSD2
9 9 9
9
: - :
Y5
8 8 : :
9 9 9 9
: - :
: 8 !
+
0V
Y6
0V
Y7
Y8
IM-T-9A
S3
iKNOW®
+24V dc
Machine
Control
K1
S4
S2
Y3
Y4
Y1
Y2
13
14
23
24
33
34
MPCE
1
*
MPCE
2
*
CONTACT/SWITCHING
DIAGRAMS
Feedback (optional)
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
* Arc Suppressors. See manual for specific warnings.
INTERNATIONAL
REPRESENTATIVES
GLOSSARY
HOOKUP
DIAGRAMS
S1
K2
254
More information online at
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD054
MMD-TA-12B DIN-Rail Muting Module
1-Channel EDM with Interface Model
0V dc
+24V dc
A1
MMD-TA-12B
A2
Page 94
Models
• MMD-TA-12B
EDM1
Y1
Y2
MMD-TA-12B
Terminal Locations
EDM2
Y3
Y4
+
OSSD1
: - :
3 3 3 3
8 8 8
8
Y5
: - :
8 8 8 8
--$4!"
OSSD2
+
0V
Y6
0V
Y7
Y8
IM-T-9A
S3
9 9 9
9
: - :
8 8 : :
9 9 9 9
: - :
: 8 !
S1
K2
+24V dc
Machine
Control
K1
S4
S2
Y3
Y4
Y1
Y2
13
14
23
24
33
34
MPCE
1
*
MPCE
2
iKNOW®
! 8 8
*
CONTACT/SWITCHING
DIAGRAMS
Feedback (optional)
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
INTERNATIONAL
REPRESENTATIVES
GLOSSARY
* Arc Suppressors. See manual for specific warnings.
HOOKUP
DIAGRAMS
!
More information online at
bannerengineering.com
255
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD055
SSM Safe Speed Monitor Module
SSM-FM-11.. to Two PNP Sensors
+V
DC common
24V ac/dc
Page 103
Models
A1
• SSM-FM-11A10
• SSM-FM-11A20
13
23
31
A2
Sensor 1
SSM-FA-11A..
Terminal Locations
A1
SSM-FM-11A10
or
SSM-FM-11A20
Y1 S1+ S1s S1-
MSCE1
+24V
S1+
Y1
PNP
Signal
Out
S1s
Y2
0V
S1-
MSCE2
MSC
Monitor
Contacts
or Jumper
SSM-FM-11A..
Sensor 2
14
24
32
Y2
S2+ S2s S2- A2
+24V
S2+
PNP
Signal
Out
S2s
0V
S2-
iKNOW®
L1
8A max.
13
Machine
Control
Circuits
CONTACT/SWITCHING
DIAGRAMS
Machine
Master Stop
Control Elements
23
K1A
K2A
K1B
K2B
K1C
K2C
14
L2
MSCE
1
*
24
MSCE
2
32
*Arc suppressor
(see WARNING)
*
HOOKUP
DIAGRAMS
31
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
INTERNATIONAL
REPRESENTATIVES
GLOSSARY
* Arc Suppressors. See manual for specific warnings.
256
More information online at
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD056
EM-T-7A Extension Module
EM-T-7A 1-Channel EDM
L1/+V dc
Machine Control Circuit
+24
V dc
Page 105
Models
EM-T-7A
A1
Y1
13
• EM-T-7A
1-Channel
Monitoring Contact
Feedback Input
(EDM)
K
23
33
43
Primary
Safety
Device
K1
EM-T-7A
Terminal Locations
K2
14
24
34
U
44
Y2
1-Channel
Monitoring Contact
Feedback Input
(EDM)
A2
£ 9£ 0
V dc
£Î ÓÎ ÎÎ {Î
*
MSC1
MSC1 MSC2 MSC3 MSC4
MSC Monitor Contacts
Machine
Master Stop
Control Elements
‡/‡Ç
K1, K2 are safety contacts
MSC2
*
MSC3
*
£{ Ó{ Î{ {{
MSC4
*
1 9Ó Ó
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
L2/-V dc
* Arc Suppressors. See manual for specific warnings.
WD057
EM-T-7A Extension Module
iKNOW®
EM-T-7A 2-Channel EDM
L1/+V dc
+24
V dc
Models
EM-T-7A
A1
13
• EM-T-7A
0
V dc
Y1
23
33
43
EM-T-7A
Terminal Locations
14
24
U
34
Y2
1-Channel
Monitoring Contact
Feedback Input
(EDM)
K
K1
K1
K2
K2
Primary
Safety
Device
HOOKUP
DIAGRAMS
Page 105
CONTACT/SWITCHING
DIAGRAMS
Machine Control Circuit
44
1-Channel
Monitoring Contact
Feedback Input
(EDM)
A2
£ 9£ *
MSC1
GLOSSARY
£Î ÓÎ ÎÎ {Î
MSC1 MSC2 MSC3 MSC4
MSC Monitor Contacts
Machine
Master Stop
Control Elements
*
K1, K2 are safety contacts.
MSC2
*
MSC3
*
£{ Ó{ Î{ {{
1 9Ó Ó
INTERNATIONAL
REPRESENTATIVES
‡/‡Ç
MSC4
L2/-V dc
* Arc Suppressors. See manual for specific warnings.
More information online at
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
bannerengineering.com
257
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD058
EM-F-7G Extension Module
EM-F-7G 1-Channel EDM
L1/+V dc
Machine Control Circuit
Page 105
EM-F-7G
Models
A1
13
1-Channel
Monitoring Contact
Feedback Input
(EDM)
Y1
23
33
43
• EM-F-7G
Primary
Safety
Device
K1
EM-F-7G
Terminal Locations
K2
14
24
34
Y2
44
0
V dc
£Î ÓÎ ÎÎ
*
£ 9£ 9Ó
1-Channel
Monitoring Contact
Feedback Input
(EDM)
A2
+24V ac/dc
MSC1
MSC1 MSC2 MSC3 MSC4
MSC Monitor Contacts
Machine
Master Stop
Control Elements
‡‡Ç
*
K1, K2 are safety contacts
MSC2
*
MSC3
*
MSC4
{Î {{ Ó
£{ Ó{
L2/-V dc
Î{
!
* Arc Suppressors. See manual for specific warnings.
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
WD059
EM-FD-7G.. Extension Module
iKNOW®
EM-FD-7G.. 1-Channel EDM
L1/+V dc
HOOKUP
DIAGRAMS
CONTACT/SWITCHING
DIAGRAMS
Machine Control Element
Page 105
EM-FD-7G2
EM-FD-7G3
EM-FD-7G4
Models
• EM-FD-7G2
• EM-FD-7G3
• EM-FD-7G4
17
27
1-Channel
Monitoring Contact
Feedback Input
(EDM)
37
A1
Y1
Y2
EM-FD-7G
Terminal Locations
K2
47
48
A2
28
18
*
£ 9£ 9Ó
0
V dc
MSC1
+24V ac/dc
GLOSSARY
MSC1 MSC2 MSC3
Machine
Master Stop
Control Elements
‡‡Ç°°
*
INTERNATIONAL
REPRESENTATIVES
*
MSC4
L2/-V dc
* Arc Suppressors. See manual for specific warnings.
258
NOTE:
This hookup is general in nature.
Your specific hookup may vary significantly,
depending on the Primary Safety Device
used and the machine control configuration.
MSC3
*
În
MSC4
MSC Monitor Contacts
K1, K2 are safety contacts
MSC2
{Ç {n Ó
1-Channel
Monitoring Contact
Feedback Input
(EDM)
38
£Ç ÓÇ ÎÇ
£n Ón
Primary
Safety
Device
K1
More information online at
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD060
IM-T-..A Interface Module
IM-T-..A 2-Channel Primary Safety Device with 2 FSDs and 2 EDM
+24V dc
0V dc
Primary
Safety
Device EDM1
Page 107
+
Models
EDM2
+
Safety Output
• IM-T-9A
• IM-T-11A
Safety Output
IM-T-..A
Terminal Locations
IM-T-9A
S3
S1
K2
K1
S4
3 3 9
S1 S2 Y1
9
13 31 23 Y2
S2
Y1
MPCE2
Y2
Y3
)-4!
9 Y4 14 32 24
9 3 3
Y3 S3 S4
MPCE1
Y4
IM-T-11A
Machine
Control
13
14
23
24
33
34
K2
K1
MPCE
1
MPCE
2
Feedback (optional)
!
* Arc Suppressors. See manual for specific warnings.
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
WD061
IM-T-..A Interface Module
+24V dc
iKNOW®
IM-T-..A 2-Channel Primary Safety Device with 2 PNP and 1 EDM
0V dc
CONTACT/SWITCHING
DIAGRAMS
Primary
Safety
Device EDM
+
Page 107
+
Safety
Output
Models
• IM-T-9A
• IM-T-11A
IM-T-..A
Terminal Locations
HOOKUP
DIAGRAMS
Safety
Output
IM-T-..A
S3
S1
K2
K1
S4
S2
Y1
S1 S2 Y1
13 31 23 Y2
Y2
Y3
MPCE2
GLOSSARY
3 3 9
9
MPCE1
Y4
Machine
Control
23
MPCE
1
14
24
MPCE
2
*
13
IM-T-11A
*
)-4!
9 Y4 14 32 24
9 3 3
Y3 S3 S4
INTERNATIONAL
REPRESENTATIVES
32
31
Feedback (optional)
* Arc Suppressors. See manual for specific warnings.
More information online at
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
bannerengineering.com
259
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD062
IM-T-..A Interface Module
IM-T-..A 2-Channel Primary Safety Device with 2 FSDs and 1 EDM
+24V dc
0V dc
Primary
Safety
Device EDM
Page 107
Safety Output
Models
• IM-T-9A
• IM-T-11A
Safety Output
IM-T-..A
Terminal Locations
IM-T-..A
S3
S1
K2
K1
S4
S2
Y1
3 3 9
S1 S2 Y1
9
13 31 23 Y2
Y2
Y3
MPCE2 MPCE1
Y4
Machine
Control
9 Y4 14 32 24
9 3 3
Y3 S3 S4
13
14
23
24
32
MPCE
1
MPCE
2
*
IM-T-11A
*
)-4!
31
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
Feedback (optional)
* Arc Suppressors. See manual for specific warnings.
WD063
IM-T-..A Interface Module
iKNOW®
IM-T-..A 1-Channel Primary Safety Device with 1 Redundant-Relay and 1 EDM
+24V dc
Primary
Safety
Device EDM
CONTACT/SWITCHING
DIAGRAMS
HOOKUP
DIAGRAMS
0V dc
Page 107
Models
Safety Output
• IM-T-9A
• IM-T-11A
IM-T-..A
Terminal Locations
IM-T-9A
S3
S1
K2
K1
S2
S4
INTERNATIONAL
REPRESENTATIVES
3 3 9
S1 S2 Y1
9
13 31 23 Y2
Y2
Y3
MPCE2
MPCE1
Y4
IM-T-11A
9 Y4 14 32 24
9 3 3
Y3 S3 S4
Machine
Control
14
23
24
33
K2
K1
Feedback (optional)
* Arc Suppressors. See manual for specific warnings.
260
13
More information online at
34
MPCE
1
MPCE
2
*
)-4!
*
GLOSSARY
Y1
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD064
DUO-TOUCH® SG Two-Hand Control Modules, STB Compatible
AT-FM-10K to Two STB Touch Buttons with Contact Outputs
STB2
STB1
+–
Page 111
+–
Blue
Models
Brown
24V ac/dc
• AT-FM-10K
White
Yellow
Black
AT-FM-10K
Terminal Locations
White
Yellow
Black
L1/+V dc
-£Ó -££ -£Î
£ £Î
ÓÎ 9£
Machine
Control
Circuit
A2
A1
AT-FM-10K
S12
S11
S13
S22
S21
S23
K1
13
23
0V ac/dc
Y1
MPCE2 MPCE1
Y2
L2/–V dc
*
K2
MPCE
1
14
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
MPCE
2
24
*
/‡‡£ä
AT-FM-10K to Two STB Touch Buttons with PNP (Sourcing) Outputs
9Ó
£{
Ó{
STB2
Ó
STB1
Logic
-ÓÎ -Ó£ -ÓÓ
Logic
+–
+–
Blue
Brown
Black
White
L1/+V dc
Black
Machine
Control
Circuit
A1
A2
AT-FM-10K
S12
S11
S13
S22
S21
S23
K1
Y1
0V dc
(1)
MPCE2 MPCE1
iKNOW®
White
Y2
L2/–V dc
*
K2
13
14
23
24
MPCE
1
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
MPCE
2
*
CONTACT/SWITCHING
DIAGRAMS
24V dc
AT-FM-10K to Two Mechanical Push Buttons with Contact Outputs
SW2
HOOKUP
DIAGRAMS
SW1
S12
S11
S13
S22
S21
S23
K1
L1/+V dc
Machine
Control
Circuit
0V ac/dc
Y1
MPCE2 MPCE1
Y2
L2/–V dc
K2
13
14
23
24
*
MPCE
1
* Arc Suppressor – See Warning
(1) See Warning about Interfacing Safety Outputs
More information online at
Wiring diagrams are for
information only. See
appropriate manuals for
all specific warnings, cautions and
information for use.
!
MPCE
2
*
* Arc Suppressors. See manual for specific warnings.
GLOSSARY
A2
A1
AT-FM-10K
INTERNATIONAL
REPRESENTATIVES
24V ac/dc
bannerengineering.com
261
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD065
STB Self-Checking Touch Buttons
Solid-State Sourcing (PNP) Outputs
Page 117
Models
1
3
• STBVP6.. models
4
Key
2
Load
MicroController
1
MicroController
2
V+
3
1
3
+
–
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
!
4-Pin Euro
bu
4
bl
2
wh
4-Pin Mini
2
4
V+
Load
4-Pin Euro
1
10-30V dc
bn
1 = Brown
2 = White
3 = Blue
4 = Black
Solid-State
+
10-30V dc
–
4-Pin 4-Wire Mini
WD066
STB Self-Checking Touch Buttons
1
Page 117
2
• STBVR81.. models
C
4
N.O.
** NOTE: Connection of dc power is without regard to polarity.
More information online at
MicroController
1
5-Pin Euro
5-Pin Mini
2
1
3
†
5
4
2
4
1
3
MicroController
2
K1
5-Pin 5-Wire
K1
1 = Brown
2 = White
3 = Blue
4 = Black
A1
5 = Gray
V+
K2
K2
A2
5*
5-Pin Euro
262
V+
bn
bl
yl
wh
bu
GLOSSARY
INTERNATIONAL
REPRESENTATIVES
5-Pin Mini
1 = Brown
2 = White
3 = Blue
4 = Black
5 = Yellow*
Relay
20-30V ac/dc
N.C.
5* †
Key
5-Pin Euro
1 = Brown
2 = White
3 = Blue
4 = Black
5 = Gray†
** Supply Voltage
(see Specifications)
3
Models
HOOKUP
DIAGRAMS
CONTACT/SWITCHING
DIAGRAMS
iKNOW®
Electromechanical Relay Output
!
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD067
DUO-TOUCH® SG Two-Hand Control Modules, STB Compatible
115V ac
230V ac
A1
24V dc
Models
Connections
Connections
to to
actuation
actuation devices
devices ––
see page 264.
see Figures 4a,
4b and 4c
AT-..M-13A
Terminal Locations
-£Ó -££ -£Î
£ Ó £ Ó
L1/+V dc
<Ó
9£ 9Ó
0V dc or
Y1
for AC hookup
MPCE1
MPCE2
MPCE4
MPCE3
Y2
13 K1
Machine
Control
Circuit
-ÓÓ -Ó£ -ÓÎ
<£
B2
Z1
Z2
S12
S11
S13
S22
S21
S23
Page 111
• AT-GM-13A
• AT-HM-13A
A2
AT-GM-13A
AT-HM-13A
B1
L2/-V dc
K2 14
23
24
33
34
43
44
51
52
MPCE
1
*
*
MPCE
2
*
MPCE
3
*
MPCE
4
/‡°°‡£Î
+24V dc
Y30
+0V dc
Y31
£Î £{
ÓÎ Ó{
ÎÎ
9Îä 9Σ 9ÎÓ
Î{ {Î
9ÎÎ x£
Y32
Y33
{{
xÓ
!
(1) See warning at left about
* Arc Suppressors. See manual
for specific warnings.
interfacing
safety outputs
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
* Arc Suppressor – See Warning
WD068
DUO-TOUCH® SG Two-Hand Control Modules, STB Compatible
iKNOW®
115V ac
230V ac
(Depending on model)
A2
A1
24V dc
AT-GM-11KM
AT-HM-11KM
B1
B2
0V dc
for AC hookup
Z2
Z3
S12
Page 111
Connections
to
Connections
to
actuation
devices
actuation
devices
––
see page see
264.Figures 6a,
Models
S13
X1
S21
S23
X2
Y1
M21
M22
Y2
L2/-V dc
<Î <{
9£
14
23
24
31
32
<Ó
9Ó ££ £Ó Ó£ ÓÓ
Machine
Control
Circuit
K2
13
SSI1
Σ ÎÓ
ÓÎ
Ó{
8Î 8{ 8x
8£ 8Ó
8È
MPCE
1
MPCE
2
*
Feedback
(optional)
/ࡡࣣ
£Î £{
*
GLOSSARY
Ó
MPCE2
9Îä 9Σ 9ÎÓ 9ÎÎ
SSI2
(2)
X3
X4
Y30
X5
X6
Y32
Y31
+24V dc
+0V dc
Y33
(2)
(2) Jumper SSI inputs if not used
* Arc Suppressors. See manual for specific warnings.
More information online at
!
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
bannerengineering.com
INTERNATIONAL
REPRESENTATIVES
£ Ó £
<£
MPCE1
HOOKUP
DIAGRAMS
M11
M12
K1
L1/+V dc
-ÓÓ -Ó£ -ÓÎ
ME
Mute
Enable
M1
M2
-£Ó -££ -£Î
ML
Mute
Lamp
Z4
S22
• AT-GM-11KM
• AT-HM-11KM
AT-..M-10K
Terminal Locations
+
S11
6b and 6c
CONTACT/SWITCHING
DIAGRAMS
Z1
263
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD069
DUO-TOUCH® SG Two-Hand Control Modules, Actuation Device Hookups
AT-..M-13A and AT-..M-11KM to Two STB Touch Buttons with Contact Outputs
STB2
STB1
+–
+–
Brown
Blue
White
Yellow
Black
White
Yellow
Black
AT-GM-13A
AT-HM-13A
Z1
Z2
S12
S11
S13
S22
S21
S23
AT-GM-13A
AT-HM-13A
AT-GM-11KM
AT-HM-11KM
!
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
!
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
!
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
AT-..M-13A and AT-..M-11KM to Two STB Touch Buttons with PNP (Sourcing) Outputs
STB2
STB1
Logic
Logic
+–
+–
iKNOW®
Brown
Blue
White
Black
White
CONTACT/SWITCHING
DIAGRAMS
Black
AT-GM-13A
AT-HM-13A
Z1
Z2
S12
S11
S13
S22
S21
S23
AT-GM-13A
AT-HM-13A
AT-GM-11KM
AT-HM-11KM
HOOKUP
DIAGRAMS
AT-..M-13A and AT-..M-11KM to Two Mechanical Push Buttons with Contact Outputs
SW2
SW1
GLOSSARY
AT-GM-13A
AT-HM-13A
INTERNATIONAL
REPRESENTATIVES
Z1
Z2
S12
S11
S13
S22
S21
S23
264
More information online at
AT-GM-13A
AT-HM-13A
AT-GM-11KM
AT-HM-11KM
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – HOOKUPS/WIRING DIAGRAMS
WD070
DUO-TOUCH® Run Bar with STBs
Page 120
5
6
STB +24V dc (Brown)
STB 0V dc (Blue)
STB 2 N.O. (Black)
Terminal
7
8
9
10
11
12
13
STB 2 N.C. (White)
4
STB 2 COM (Yellow, if used)
3
STB 1 N.C. (White)
• STBVP6-RB1..
2
STB 1 COM (Yellow, if used)
14
NOTE: The STBVP6 hand control buttons are
pre-wired to terminals 1, 3, 4, 5, 6, and 8.
Terminals 2 and 7 are reserved for use of
STBVR81 buttons.
Connection of EZ-LIGHT indicator(s) and
QD connectores not shown. (See data sheet
P/N 131634 for details)
!
Wiring diagrams are for information only.
See appropriate manuals for all specific
warnings, cautions and information for use.
WD071
EZ-LIGHT™ for Two-Hand Control
Brown Wire
Gray Wire
Black Wire
White Wire
Red ON
+V dc
—
—
—
Stop and/or Not Ready
Blue ON
+V dc
+V dc
—
—
Stopped, but Ready/Enabled
Green ON
+V dc
+V dc
+V dc
—
Yellow ON
+V dc
+V dc
+V dc
+V dc
Red Flashing
Go
Mute Condition
Abnormal State
HOOKUP
DIAGRAMS
CONTACT/SWITCHING
DIAGRAMS
NOTES:
• Blue wire connected to 0V dc
• Supply Voltage and Current = 10 to 30V dc, 60 mA max.
GLOSSARY
Page 192
Any other hookup combination
Typical Function
iKNOW®
LED Function
INTERNATIONAL
REPRESENTATIVES
1
STB 1 N.O. (Black)
Models
More information online at
bannerengineering.com
265
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
GLOSSARY
A
Category 0 Stop (Functional)
A type of perimeter guarding, typically used to
guard doorways, cell entries or exits, walkways, and
machine access points.
Category 1 Stop (Functional)
An uncontrolled stop produced by immediately
removing power to the machine actuators.
Access guard
Adjustable guard
A guard that can be adjusted to accommodate various
jobs or set-ups.
Angle of Divergence/Acceptance
Anti-tie down
A feature of a two-hand control where both hand
controls must be released before the machine can
restart. 
Antirepeat
The function of the control system designed to limit
the machine to a single stroke or cycle even if the
tripping or actuating means is held operated.  
Area guard
A safeguarding technique that provides a means of
continually sensing or detecting an individual within an
area adjacent to or associated with a hazard.  
Area-scanning device
A safeguarding device that creates a sensing plane to
detect the presence of an individual or object.
Auto power-up
A safety light screen system feature that enables
the system to be powered up into the RUN mode (or
recover from a power interruption) without requiring a
manual reset. 
Awareness device
HOOKUP
DIAGRAMS
CONTACT/SWITCHING
DIAGRAMS
iKNOW®
A barrier, signal, light or signage that warns individuals
of an approaching, present, or the proximity of a
hazard. 
B
The failure of multiple components or equipment
resulting from the same root cause.
Complementary Protective Equipment
Devices used to assure or supplement the operation
of a primary safeguard.
Contact
The portion of a beam that must be blocked to cause
an individual photo receiver to change state. One of
the factors in determining resolution of a safety light
screen. Also known as effective beam diameter.
Contact configuration
Blanking
An optional function that allows a light screen system
to ignore objects located within the sensing field so as
not to create an OFF-state of the safety outputs and
cause a Trip or Latch condition. 
A condition that occurs when an opaque object of
sufficient size interrupts one or more light screen
beams. When a blocked condition occurs, OSSD1
and OSSD2 outputs simultaneously turn off within the
system response time.  
C
Cascade
Series connection (or “daisy-chaining”) of multiple
sensors.
266
More information online at
Duplication or redundant system that minimizes the
possibility of a failure to danger in the event of a
single fault. This is because the second independent
channel maintains the ability to arrest dangerous
motion.
E
Effective Aperture Angle (EAA)
The maximum angle of deviation from the optical
alignment of the emitter and the receiver within which
the safety light screen continues in normal operation.
Also known as Angle of Divergence/Acceptance, or
Field-of-View.
The “working” part of a photoelectric beam. Not to
be confused with the actual radiation pattern of the
emitter, or with the field of view of the receiver.
Electromechanical relay
Refers to the construction of a relay or a switch, in
many configurations, for example, SPDT (Form C),
with one normally open, one normally closed, and one
common between the two. 
Control reliability
Conventional switching relays consisting of “hard”
contacts (metal-to-metal), switched to opened
or closed position by applying voltage to an
electromagnetic coil.
Electro-Sensitive Protective Equipment (ESPE)
A method of ensuring the performance integrity of a
control system or device. Control circuits are designed
and constructed so that a single failure or fault within
the system does not prevent the normal stopping
action from being applied to the machine when
required, or does not create unintended machine
action, but does prevent initiation of successive
machine action until the failure is corrected.
Control Relay (CR)
A relay that is used to perform logic functions in a
machine control circuit.
An assembly of devices and/or components working
together for protective tripping or presence sensing
purposes and comprising as a minimum: a sensing
device, controlling/monitoring devices, and output
signal switching devices. See IEC61496-1
Emergency Stop
A control function that is initiated by a single human
action to arrest dangerous machine motion, or
otherwise avert arising or reduce existing hazards to
persons, damage to machinery or to work in progress.
See ANSI/NPFA79, IEC60204-1, or ISO13850.
EMI
Crosstalk (Optical)
Optical crosstalk occurs when a photoelectric receiver
responds to light from an adjacent emitter.
Beam Spacing
The distance from the center of one beam to the
center of an adjacent beam, and one factor in
determining resolution of a safety light screen. Also
known as beam pitch.
Dual channel
Effective beam
One of the current-carrying parts of a relay, switch, or
connector that open and close to complete associated
electrical circuits.
The stopping of machine motion while retaining power
to machine actuators during the stopping process.
Beam Diameter
See Depth Penetration Factor.
A controlled stop with power left available to the
machine actuators.
Controlled stop
Blocked condition
GLOSSARY
Category 2 Stop (Functional)
Common mode failure
See Effective Aperture Angle (EAA)
INTERNATIONAL
REPRESENTATIVES
A controlled stop achieved with power remaining to
the machine actuators. Power is removed after the
stop is achieved.
Dpf
D
Defined area
The “screen of light” generated by a safety light
screen system, defined by the height and the
separation of the emitter and receiver. When the
defined area is interrupted by an opaque object of
a specified cross section, a Trip or Latch condition
results.
Depth of field
The distance, length or the size of the sensing surface
or field from the outer edge toward the hazard. Also
known as “depth of detection.”
Abbreviation for Electromagnetic Interference.
Electrical “noise” which may interfere with proper
operation of sensors, programmable logic controllers,
counters, data recorders, and other sensitive
electronic equipment.  
Emitter
The light-emitting component of a safety light
screen system, consisting of a row of synchronized
modulated LEDs. The emitter, together with the
receiver (placed opposite), creates a “screen of light”
called the defined area.
Exact blanking
A configuration allowing a light screen system to
ignore stationary objects (such as brackets or fixtures)
that interrupt a specific number of light beams.
External device monitoring
A means by which a safeguarding device monitors the
state of external devices that may be controlled by the
safety device.
Depth penetration factor
Compensation factor for distance an object can
penetrate the sensing field of a Presence Sensing
Safeguarding Device (PSSD) before the device
reliably detects the intrusion and signals a stop. Often
abbreviated as Dpf.
Diverse-redundancy
The practice of using components, circuitry or
operation of different designs, architectures or
functions to achieve redundancy and to reduce the
possibility of common mode failures. 
F
Fail-safe
A description of a circuit or system that is guaranteed
not to fail in the event of a malfunction so that the
catastrophic loss of function is not possible.
Fail to Safe
A design or event in which a failure or fault within a
system causes the hazardous machine motion or
process to achieve a safe state (Commonly confused
with “fail-safe”).
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
GLOSSARY
Good Engineering Practice
A protective physical barrier that prevents an
individual from accessing a hazardous area.
H
Hand control
Hard guard
Screens, bars, or other mechanical barriers affixed to
the frame of the machine intended to prevent entry by
personnel into the hazardous area(s) of a machine.
G
General Duty Clause
Section 5(a)(1) of the Occupational Safety and Health
Act of 1970 (Public Law 91-596, 91st Congress,
S.2193, 29Dec1970) places primary accountability
on the employer for work place safety. “5(a)(1) Each
employer shall furnish to each of his employees
employment and a place of employment which are
free from recognized hazards that are causing or
are likely to cause death or serious physical harm to
his employees.” OSHA inspectors often use section
5(a)(1) of the “General Duty Clause” as the bases of
citations resulting from on-site inspections.
General Requirements for All Machines
(29CFR1910.212) requires that one or more methods
of machine guarding shall be provided to protect the
operator and other employees from hazards, and
the guarding device shall be in conformity with any
appropriate standards.
The response of a safety or safeguarding device in
which an OFF-state is maintained after the device
has been actuated until the safeguard is cleared,
re-closed, or re-armed and a manual reset is
performed.
A potential source of harm.
Hazard point
Legend
The closest reachable point of the hazardous area.
Hazardous area
An area that poses an immediate or impending
physical hazard.
Any type of marking, sign, or inscription which
identifies the device type, function or purpose.
Lockout Condition
A safety system condition that is automatically
attained in response to certain failure modes (an
internal lockout). When a Lockout condition occurs,
the safety system’s safety outputs turn OFF, the
failure must be corrected, and a manual reset is
required to return the system to RUN mode.  
Hazardous situation
A circumstance in which a person is exposed to a
hazard, or any specific activity done on or around the
machine during its lifecycle that results in a potential
source of harm. See B11.TR3 for further information.
Forced-guided contacts
Relay contacts that are mechanically-linked, so that
when the relay coil is energized or de-energized, all
of the linked contacts move together. If one set of
contacts in the relay becomes immobilized, no other
contact of the same relay will be able to move. The
function of forced-guided contacts is to enable the
safety circuit to check the status of the relay. Forcedguided contacts are also known as “mechanicallylinked contacts,” “positive-guided contacts,” “captive
contacts,” “locked contacts,” or “safety relays.”
Latch condition
Hazard
FMEA
Abbreviation for Failure Mode and Effects Analysis,
a testing procedure by which potential failure modes
in a system are analyzed to determine their results or
effects on the system.
In a safety light screen application, the installation
of two emitter/receiver pairs to create a vertical
and a horizontal sensing field. Gains advantages of
both area guarding and point-of-operation guarding
techniques to reduce the possibility of pass-through
hazards. 
I
I/O
M
Machine response time
The time between the activation of a stopping device
and the instant when the dangerous parts of the
machine reach a safe state.  
(Input-Output) Provides communication channels to
system and to manufacturing process.
Integrity
The degree to which a circuit, system or device can
be expected to perform unimpaired an anticipated
function in the event of a fault. Integrity depends
on several characteristics including fault tolerance,
fault exclusion, risk reduction, reliable and well-tried
components, well-tried safety principles, and other
design considerations.
iKNOW®
A way to configure a light screen system to ignore
stationary objects (such as brackets or fixtures) that
are always present at a specific location within the
defined area.
L Configuration
Machine secondary control element (MSCE)
An electrically-powered element, independent of
the machine primary control element(s), capable
of removing power from the machine’s actuator
(prime mover) of the relevant hazardous parts and is
typically controlled by the secondary switching device
(SSD).
Master Control Relay (MCR)
Interlocked guard
A relay that is used to provide electrical power to the
machine control circuitry. Typically interfaced with the
Master Start/Stop (ON/OFF) and Emergency Stop
functions.
A guard or barrier interfaced with a machine
control system so as to restrict access to or prevent
inadvertent access to the hazard.
Internal lockout
A Lockout condition due to an internal safety system
problem.
Master Stop Control (MSC)
An electrically-powered device, external to the
E-stop Safety Module, that provides a safety stop by
immediately removing electrical power to the hazard
and, if necessary, by applying braking to dangerous
motion.
Intrinsic safety
A design technique applied to electrical equipment,
such as sensors, switches, and wiring for hazardous
locations. The technique involves limiting energy
to a level below that required to ignite a specific
hazardous atmosphere. Intrinsic safety design
often eliminates the requirement for explosion-proof
enclosures. Also see “NAMUR”.
CONTACT/SWITCHING
DIAGRAMS
Fixed blanking
L
A hand-operated mechanism or device used as an
actuating control. Two normally open “input switches”
are used as hand controls in a two-hand control
system
Final Switching Device (FSD)
Component of a safety-related control system that
interrupts the circuit to the machine primary control
element (MPCE) when the output signal switching
device (OSSD) goes to the OFF-state.
A key-operated switch used to reset a safety system
to the RUN mode following a Lockout condition or to
reset a safety system from a Latch condition. 
The machine whose point of operation or other
hazardous area is guarded by the safety system.  
Fault tolerance
The ability of a system to function as it was designed
even in the presence of faults or failures. 
Key reset
Guarded machine
Fault exclusion
The ability to minimize or eliminate known possible
failures or faults through design, selection of
components, or implementation of additional
measures. 
K
Guard
Fault
The state of an item (e.g. component, circuit, device
or machine) characterized by its inability to perform a
required function. A fault is often the result of a failure
of the item itself, but may exist without prior failure.
See Failure.
A rating system established by the IEC which defines
the suitability of sensor and sensor system enclosures
for various environments. Similar to NEMA ratings for
enclosures. 
HOOKUP
DIAGRAMS
Failure to danger
A failure which delays or prevents a safety system
from arresting dangerous machine motion, thereby
increasing risk to personnel.  
IP rating
Minimum guidelines that specify commonly-used
and recognized design principles, well-tried and
robust components, and safety practices to make the
workplace free of industry recognized hazards and
compliant to relevant standards.
GLOSSARY
An event in which an item (e.g. component, circuit, or
device) ceases to perform its required function. 
Mechanically-linked contact
See Forced-Guided Contact.
Monitoring
More information online at
The verification of system components to detect
failures or faults of any part of the monitored system
that could affect the performance of safety-related
functions.
bannerengineering.com
INTERNATIONAL
REPRESENTATIVES
Failure
267
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
GLOSSARY
Minimum Object Sensitivity (MOS)
Output Signal Switching Device (OSSD)
The minimum-diameter object that a safety light
screen system can reliably detect. Objects of this
diameter or greater will be detected anywhere in the
defined area. A smaller object can pass undetected
through the light if it passes exactly midway between
two adjacent light beams.
Abbreviation for Output Signal Switching Device.
The safety outputs of a safeguarding device that are
used to initiate a stop signal by achieving an OFFstate. (Note: Includes, but is not limited to, solid-state
outputs, relay contacts, or other electrical contacts.)
P
Machine Primary Control Element (MPCE)
An electrically-powered element, external to the
safety system, which directly controls the machine’s
normal operating motion in such a way that the
element is last (in time) to operate when machine
motion is either initiated or arrested. (Examples
include motor/motor contactors, magnetic clutch
brake, or electrically operated valve.)
Master Stop Control (MSC)
An electrically-powered device, external to the
E-stop Safety Module, that provides a safety stop by
immediately removing electrical power to the hazard
and, if necessary, by applying braking to dangerous
motion. This stopping action is accomplished by
removing power to the actuator coil of either Master
Stop Control Element.
Muting
The automatic suspension of the safeguarding
function of a safety device during a non-hazardous
portion of the machine cycle.
N
Devices and sensors designed for use with certified
switching amplifiers with intrinsically-safe circuits.
NAMUR sensors are most commonly used in
explosive environments.
Normally Closed (NC)
Designation that states the contacts of a switch or
relay are closed or connected when at rest. When
activated, the contacts open or separate.
iKNOW®
A situation that may exist when personnel pass
through a safeguard (at which point the hazard stops
or is removed), and then continue into the guarded
area. At this point the safeguard may not be able to
prevent an unexpected start or restart of the machine
with personnel within the guarded area.
Perimeter guard
A safeguarding technique that provides a barrier or
means of detection at the boundary of a hazard or
hazardous area.
PNP output (Current sourcing)
A transistor available as an output switch in DC
sensors. Usually configured with its collector open
and its emitter connected to the positive of the
sensor supply voltage. In this configuration, a load is
connected between the output (collector) and ground
(DC common). This output configuration is also called
a “sourcing” output.
Point of operation
NAMUR
CONTACT/SWITCHING
DIAGRAMS
Pass-through hazard
Normally Open (NO)
Designation that states the contacts of a switch or
relay are normally open or not connected. When
activated, the contacts close or become connected.
NPN output (Current sinking)
A transistor available as an output switch in DC
sensors and logic modules. Usually configured
with its collector open and its emitter connected to
ground (DC common). In this configuration, a load
is connected between the output (collector) and the
positive of the DC supply. This output configuration is
also called a “sinking” output.
The location of a machine where material or a
workpiece is positioned and a machine function is
performed upon it.
Point-of-operation guarding
Safeguards, such as hard guards or safety light
screens, which are designed to protect personnel
from hazardous machine motion associated with the
machine’s point of operation.
Positive-guided contact
See Forced-guided contact.
Positive Opening (Safety Switch)
Safety switch that employs a rigid mechanical link
from the actuator to open Normally Closed contacts.
The normal operation of the switch will force apart
contacts, even those that are welded shut.
Power monitoring
Monitoring function accomplished through a seriesparallel connection of contacts that provide feedback
about the machine’s status. Power is supplied to
the module as long as both contactors work as they
should.
HOOKUP
DIAGRAMS
Power-Up/Power-Interrupt Lockout
A Lockout condition of a safety light screen system
that, if Auto Power-Up is OFF, occurs when the
system is powered up (including power-ups after a
loss of power).
O
GLOSSARY
OFF State
Presence-sensing device
The state in which the output circuit is interrupted and
does not permit the flow of current.
ON State
Presence-Sensing Device Initiation (PSDI)
The state in which the output circuit is complete and
permits the flow of current.
INTERNATIONAL
REPRESENTATIVES
Optical short circuit
More information online at
An application in which a presence-sensing device is
used to start the cycle of a machine.
A safeguarding device attached to an operator’s
hands and wrists that withdraws the operator’s hands
from the hazard area during hazardous operation.
Q
Qualified Person
An individual who, by possession of a recognized
degree or certificate of professional training, or by
extensive knowledge, training, and experience,
has successfully demonstrated the ability to solve
problems relating to the subject matter and work.
R
Receiver
The light-receiving component of a safety light
screen system, consisting of a row of synchronized
phototransistors. The receiver, together with the
emitter (placed opposite), creates a “screen of light”
called the defined area.
Reduced resolution
A configuration that allows a light screen system to
intentionally ignore the interruption of consecutive
light beams within the defined area. The effect is to
ignore multiple objects with cross-sections less than a
certain size, while increasing the size of an object that
will be reliably detected anywhere within the defined
area. Sometimes called “Floating Blanking.”
Redundancy
The duplication of components or circuitry providing
the same function should a component or circuit fail.
Reliability
The ability of a machine’s circuits and components
to consistently perform its stated function within its
specifications without failing.
Relay
An electromechanical device that opens or closes
contacts in response to a small current or voltage
change of an electric circuit. This device effects the
operation of other devices in the same or another
electric circuit.
Reset
The use of a manually-operated switch to restore the
safety outputs to the ON state from a Latch condition,
or return to the RUN mode from a Lockout condition.  
Resolution
The minimum size (diameter or cross section) of an
object that a safety light screen will reliably detect.
Calculated by adding the beam spacing dimension to
effective beam diameter. Objects of this size or larger
will be detected anywhere in the sensing field.
Risk
The probability of the occurrence of harm and its
severity.
Risk assessment
A procedure used in machine safety to identify,
document and eliminate or reduce hazards in a
particular machine or process.
S
Presence-Sensing Safeguarding Device (PSSD)
Deflection of one or more beams around an object
in the defined area which may result in reduced
detection capability of a light screen or in the worst
case, of an object being allowed to pass through
undetected. The result of locating a sensing field
next to a highly reflective surface e.g. stainless steel,
glossy paint.
268
A device that creates a sensing area to detect the
presence of an individual or object.
Pull-back
Abbreviation for Presence-Sensing Safeguarding
Device. A presence-sensing device used as a
safeguard.
Safeguard
A guard (barrier) or safeguarding device used to
protect personnel from hazards by preventing or
restricting access, or by detecting the presence of an
individual.
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
GLOSSARY
A technique or means to reduce the risk of harm to
personnel from a machine hazard which includes but
is not limited to Safety Light Screens, Emergency
Stop Buttons, Guards (barriers), Interlocking,
Enabling Pendants, Two-hand Control, Restraints, or
Lockout/Tagout equipment.
Safety distance
The calculated distance between a hazard and its
associated safeguard.
Safety edge
A safeguarding device consisting of a sensing edge
and a control, used to detect individuals who comes
into contact with the sensing edge.
Safety interlock switch
A switch on a guard barrier used to detect if the
guard is opened. Designed to prevent intentional
defeat. Electromechanical safety interlock switches
use positive opening contacts. Other forms of safety
interlock switch include magnetic, RF tag, optical, or
inductive. 
Safety light curtain
See safety light screen.
Safety light screen
A safeguarding device comprising an LED array
emitter and receiver element which creates a sensing
field or plane. When an individual or object interrupts
this sensing field, the light screen detects the
interruption and initiates a stop command. Also known
as Active Opto-electronic Protective Device -AOPD,
Presence Sensing Safeguarding Device, safety light
curtain, light devices and optical guards. 
Safety mat
A safeguarding device consisting of a sensing surface
and a control. The sensing surface is capable of
detecting the presence of individual(s) on its surface.
Self-checking circuitry
A circuit with the capability to verify that all of its own
critical safety circuit components, along with their
redundant backups, are operating properly.  
Safety relay
An electromechanical relay with force-guided
contacts which allow the monitoring of a safety
device’s circuit to check relay status. See also forceguided contacts.
Safety stop
Removal of power to the Machine Primary Control
Elements that allow for an orderly cessation of
motion for safeguarding purposes. Also known as a
Protective Stop.
Safety Stop Interface (SSI)
An interface which provides the means to integrate
external devices to effect a stop command. It consists
of two input channels (A&B), which are compatible
with devices that have two Normally Open hard
contacts or relay outputs.
A set of design, construction and testing requirements
for light screens described by IEC 61496. The “types”
perform differently in the presence of faults and under
influences from environmental conditions. Type 4
requirements are the most stringent.
Separation distance
The calculated distance between a hazard and its
associated safeguard. See Safety distance.
Simultaneity
Concurrent events, actions, or actuations occurring
within a specific time frame. This time frame is 0.5
second in a Two-Hand Control or Two-Hand Trip
applications per ANSI B11.19, ANSI/RIA R15.06
and ISO 13851 (Note: ISO 13851 defines this as
synchronous actuation).
U
Uncontrolled stop
Solenoid
A coil equipped with a movable iron core that will
produce linear motion as a result of current passing
through the coil (the iron core is pulled into the center
of the coil). When current is removed, a spring returns
the iron core to the original position.
Secondary Switching Device (SSD)
Abbreviation for Secondary Switching Device. An
output which, in a lock-out condition, performs a
back-up safety function by going to the OFF-state and
initiating an appropriate machine control action.
The stopping of machine motion by removing power
to the machine actuators, all brakes and/or other
mechanical stopping devices being activated.
Universal Safety Stop Interface (USSI)
Abbreviation for Universal Safety Stop Interface. An
interface that provides a means to integrate external
devices to effect a stop command. It consists of two
input channels (A&B), which are compatible with
Banner solid-state OSSD outputs with “handshake”
verification (two-wire hookup), or with devices that
have two normally open hard contacts or relay
outputs (four-wire hookup).
Safety Stop Interface (SSI)
Abbreviation for Safety Stop Interface. An interface
which provides the means to integrate external
devices to effect a stop command. It consists of two
input channels (A&B), which are compatible with
devices that have two normally open hard contacts or
relay outputs.
Standards
A specification, criterion or benchmark that is widely
used, accepted or is sanctioned and codified by a
standards agency. Safety standards are minimum
requirements for product and machine design,
manufacture, use and evaluation.
Supplemental guarding/safeguarding
Additional means used to prevent or hinder personnel
from accessing the guarded hazard by augmenting
the primary means of safeguarding.
T
Safety module
A device that performs a specific safety function(s)
and consists of monitored, multiple, mechanicallylinked relays, or monitored solid-state safety
outputs. Commonly confused with a single, discrete
mechanically-linked “safety” relay. Also know as
Safety Interface Module or Safety Relay Modules.
Type 4 safety light screen
iKNOW®
Safety device
A set of design, construction and testing requirements
for light screens described by IEC 61496. The “types”
perform differently in the presence of faults and under
influences from environmental conditions. Type 2
requirements are less stringent than those for Type
3 or Type 4
CONTACT/SWITCHING
DIAGRAMS
A device that detects or prevents inadvertent access
to a hazard (i.e. not a guard or a barrier). Also known
as a Protective Device.
Type 2 light screen
An output which, in a lock-out condition, performs a
back-up safety function by going to the OFF-state and
initiating an appropriate machine control action.
Trip condition
The response of a safety or safeguarding device in
which an ON-state is achieved when the safeguard
is cleared, re-closed, or re-armed, without operator
intervention.
HOOKUP
DIAGRAMS
Safeguarding device
Secondary Switching Device (SSD)
Trip initiate
The resetting, reclosing, or clearing of a safeguard
causing the initiation of machine motion or operation.
Trip Initiate is not allowed as a means to initiate a
machine cycle per NFPA 79 and ISO 60204-1, and is
commonly confused with PSDI.
GLOSSARY
Measures (including guards, safeguarding devices,
awareness devices, safeguarding methods, or safe
work procedures) used to protect personnel from
hazards which cannot reasonably be eliminated, or
from the risks which cannot be sufficiently reduced by
inherently safe design measures.
Two-hand control device
An actuating control that requires concurrent
actuation of both of the operator’s hands to initiate
and control machine motion during the hazardous
portion of the machine cycle.
INTERNATIONAL
REPRESENTATIVES
Safeguarding
Two-hand trip
An actuating control that requires concurrent
actuation of both of the operator’s hands to initiate the
machine cycle. Typically used on full revolution clutch
or single-stroke machines.
More information online at
bannerengineering.com
269
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – INT. REPRESENTATIVES
North America
UNITED STATES
More than 150 representatives and distributors covering all states. For a complete listing, go to bannerengineering.com and find
your local Banner Representative by ZIP code search.
Canada
E. B. Horsman & Son Ltd.
13055 80th Avenue
Surrey, British Columbia V3W 3B1
Tel: 1-604-596-7111
Fax: 1-604-596-3139
http://www.ebhorsman.com
Landel Controls Ltd.
#250, 5701-17 Ave SE
Calgary, Alberta T2A 0W3
Tel: 1-403-254-8900
Fax: 1-403-254-8903
email: [email protected]
http://www.landelcontrols.com
Le Groupe Rotalec
900 McCaffrey
Ville St-Laurent, Quebec H4T 2C7
Tel: 1-514-341-3685
Fax: 1-514-341-5205
email: [email protected]
http://www.rotalec.com
Le Groupe Rotalec/Seltron
114 Woodlawn Road
Unit 34B, Suite 608
Dartmouth, Nova Scotia B2W 2S7
Tel: 1-902-829-3666
Fax: 1-902-829-2525
email: [email protected]
http://www.rotalec.com
Shelley Industrial Automation, Inc.
41 Coldwater Road
Toronto, Ontario M3B 1Y8
Tel: 1-877-SHELLEY
Fax: (416) 447-9313
email: [email protected]
http://www.shelley.com
Le Groupe Rotalec Atlantic
Moncton Division of Seltron
122 Driscoll Cresent
Moncton, New Brunswick E1E 3R8
Tel: 1-506-858-9884
Fax: 1-506-853-4185
email: [email protected]
http://www.rotalec.com
Latin America
Sensorville (Santa Catarina)
Rua Gothard Kaesemodel, 657
Joinville, SC 89203-400
Tel: 55-47-3422-5111
Fax: 55-47-3433-5298
email: [email protected]
http://www.sensorville.com.br
Movimatic (São Paulo)
Rua Vigário Albernaz, 226
São Paulo, SP 04134-020
Tel: 55-11-5062-5222
Fax: 55-11-5062-5222
email: [email protected]
http://www.movimatic.com.br
INTERNATIONAL
REPRESENTATIVES
HOOKUP
DIAGRAMS
Brazil
Sensor do Brasil (São Paulo Rio de Janeiro)
Rua Jordão Schiavetto, 436
Parque Ortolandia
Hortolândia, SP 1318-080
Tel: 55-19-3897-9400
Fax: 55-19-3897-9426
email: [email protected]
http://www.sensordobrasil.com.br
GLOSSARY
CONTACT/SWITCHING
DIAGRAMS
iKNOW®
Argentina
Aumecon S.A.
Acassusso 4768
1605 Munro
Buenos Aires CP B1605BFP
Tel: 54-11-4756-1251
Fax: 54-11-4762-6331
email: [email protected]
http://www.aumeco.com.ar
Sensorpar Eletro Eletronica E
Automacao Ltda (Parana)
Av. Senador Salgado Filho
4291 Sl 06 Bairro: Uberaba
Curitiba-PR 81580-000
Tel: 55-41-3284-6660
Fax: 55-41-3284-6660
email: [email protected]
http://www.sensorpar.com.br
270
More information online at
Spheric Componentes Óticos
(Rio Grande do Sul)
Rua Imperatriz Leopoldina, 355,
Sala 03
Novo Hamburgo – RS 93310-060
Tel: 55-51-3594-8036
Fax: 55-51-3594-8036
email: [email protected]
http://www.spheric.com.br
Techway Comércio e
Representação Ltda
Av Santa Cruz Machado
4048 Conj. 31 de Março
Japiim I, Manau-Amazonas
Tel: 55-92-3613-6613
Fax: 55-92-3613-2161
email: [email protected]
http://www.techwaybr.com.br
Weber Automação e Controle
Industrial Ltda
Rua Bicas, 215 – Bairro Sagrada Família
Belo Horizonte – Minas Gerais BR
31030-160
Tel: 55-31-3461-4222
Fax: 55-31-3481-7925
email: [email protected]
http://www.webercom.com.br
Ztech Sensores Ltda. (São Paulo)
Rua Itagyba Santiago, 462
São Paulo, SP - 04635-052
Tel: 55-11-5031-7777
Fax: 55-11-5031-7777
email: [email protected]
http://www.ztechsensores.com.br
Bolivia
Control Experto
Oficina Principal
Av America E-435
Edificio Jaque, Piso # 2 ofic #2
Cochabamba
Tel: 591-4412-4039
Fax: 591-4445-0546
email: [email protected]
http://www.controlexperto.com
Control Experto
Av. Pasos Kanki N 1649
Edificio San Martín de Porres
Piso 4 Oficina A-4 - Zona Miraflores
La Paz
Tel: 591-(2)-222-2597
Fax: 222-6923 – 212-9247
email: [email protected]
http://www.controlexperto.com
Control Experto
Cuarto Anillo entre Av. Paragua y
Mutualista
Condominio Colombo
Oficina Nº3
Santa Cruz
Tel: 591-(3)-364-4753
Fax: 591-(3)-364-4753
email: [email protected]
http://www.controlexperto.com
Chile
Electromática Ltda
Avda. Manuel Rodriguez 843
Concepción CP 406-1192
Tel: 56-41-229-4000
Fax: 56-41-229-4001
email: [email protected]
http://www.electromatica.cl
Electromática Ltda.
Avda. Argentina 1609 Of 401
Antofagasta
Tel: 56-55-464-400
email: [email protected]
http://www.electromatica.cl
Electromática Ltda.
Puerto Mott
Tel: 56-65-264-219
Electromática Ltda.
Avda. Santa Magdalena 75 of 212
Santiago
Tel: 56-2-495-9400
email: [email protected]
http://www.electromatic.cl
Seiman S.A.
1 Norte 1511
Viña del Mar
Tel: 56-41-222-3239
Fax: 56-41-222-3281
email: [email protected]
http://www.seiman.cl
Seiman S.A.
Angol 436, Of 303 – Edificio Millenium
Concepción
Tel: 56-32-222-3239/3281
http://www.seiman.cl
Seiman S.A.
Manuel Montt 099
Pf. 204 - Providencia
Santiago
email: [email protected]
http://www.seiman.cl
Colombia
Coldecon Ltda
Calle 7 Sur-Nº 51A-21
Interior 172 - Piso 3
Mall Providencia, Medellín
Tel: (57)(4) 3615577
Fax: (57)(4) 3610189
email: [email protected]
http://www.coldecon.com.co
Hi-Tech Medellín
Av. Bolivariana. Cra 66 B No. 39-22
Medellín (Antioquía)
Tel: 57-4-265-5358 / 57-4-265-3240
Fax: 57-4-265-8216
email: [email protected]
Hi-Tech Pereira
Cra 5 No. 16-27, Local 4
Pereira (Risaralda)
Tel: 57-63-257-441
Fax: 57-63-352-455
email: [email protected]
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – INT. REPRESENTATIVES
Ecuador
Bracero & Bracero Ingenieros
Gonzalo Hidalgo 135 y Gualberto Perez
Quito
Tel: 593-2-264-1598
Fax: 593-2-265-8223
email: [email protected]
http://www.bracero-ingenieros.com
Equipamiento Electro Industrial SA
Km 7.5 Via Daule
Parque Comercial California #2
Bloque J
Guayaquil
Tel: 593-42-100134/36/37
email: [email protected]
Krahuer S.A.
Mapasingue Oeste
Av. Segunda y Calle Primera, esquina
P.O. Box 9910
Guayaquil
Tel: 593-9-6015386
Fax: 593-4-2351312
email: [email protected]
Guatemala
Enersys Co.
5 Calle 35-01, Zona 11
Utatlán II
Guatemala City
Tel: 502-2439-4622
Fax: 502-2434-6876
email: [email protected]
Mexico
Automation International Ltd.
13006 Mula Lane
Stafford, TX 77477
Tel: 281-879-9505
Fax: 281-879-9510
email: [email protected]
http://www.ail-us.com
Automatic Controls del
Noreste S.A. de C.V.
Ing. Juan Hermilo Suarez Rodriguez
Carretera 57 #3100
Colonia Estancias de Santa Ana
Monclova Coahuila
C.P. 25830
Tel: 52-866-639-2579
Fax: 52-866-639-2568
email: [email protected]
CALVEK S.A. de C.V.
Carr. 57 Km 423
Col. Talleres Local 7
C.P. 78399
San Luis Potosí, S.L.P. 78434
Tel: 444-567-5327
Fax: 444-128-6122
email: administració[email protected]
Control Sensors, S.A. de C.V.
Av. Tolteca # 2300-A
Col. Tolteca
Guadalupe, N.L. C.P. 67190
Tel: 818-030-73-07/09
email: [email protected]
Hobby Electrónica S.A. de C.V.
Retorno Corregidora 173-D
Col. Balaustradas
Querétaro, Qro. 76070
Tel: 442-213-8790
Fax: 442-223-4844
email: [email protected]
http://www.hobbyelectronica.com
IIPSA - Instrumentos Industriales del
Pacifico, S.A. de C.V.
Juan Carrasco # 212 Pte.
Col. Centro
Los Mochis- Sinaloa 81200
Tel: 668-816-0140
Fax: 668-816-0144
email: [email protected]
http://www.iipsa.com
INASA: Ingenieria y Abastecimiento,
S.A. de C.V.
Villagran 1423 Nte., Postal 426
Monterrey, NL 64440
Tel: 81-8375-2377
Fax: 81-8372-7157
email: [email protected]
Seguridad y Control
Av. Federalismo Sur # 765, Col. Moderna
Guadalajara, Jal. 44190
Tel: 33-3614-5554
Fax: 33-3614-1253
email: [email protected]
http://www.seguridadycontrol.com.mx
TESLA Internacional
Encinos Ote. 13 Arcos del Alba
Cuatitlán Izcalli, Edo. de México 54750
Tel: 55-5871-3468
Fax: 55-5871-5556
email: [email protected]
NICARAGUA
Feldmann Y Cia Ltda
Del Rest. Munich 2c arriba y 100 mts
al lago
Managua
Tel: 505-266-8104
Fax: 505-266-8104
email: [email protected]
AmeTrade C.A.
Av. Henry Ford, Zona Industrial Norte
C.C. Paseo Las Industrias, 2da Etapa
Nivel 1, Ofic. 1-118 Valencia
Tel: 58-241-838-4250
Fax: 58-241-838-3143
email: [email protected]
http://www.ametrade.com
AmeTrade C.A.
Caracas
Tel: 58-212-210-5461
email: [email protected]
http://www.ametrade.com
AmeTrade C.A.
Puerto Ordaz
Tel: 58-286-713-5060
email: [email protected]
http://www.ametrade.com
AmeTrade C.A.
Maracaibo
Tel: 58-261-200-5067
email: [email protected]
http://www.ametrade.com
AmeTrade C.A.
Barquisimeto
Tel: 58-251-710-5068
email: [email protected]
http://www.ametrade.com
Cadeci C.A.
C.C. Ara. Nave G, Local 80-A-18
Prolongación Av. Michelena
Valencia, Carabobo
Tel: 58-241-838-4915 / 58-241-834-5
Fax: 58-241-832-2566
email: [email protected]
Peru
NPI Peru S.A.C.
Ricardo Aicardi #361
Surco, Lima 33
Tel: 51-1-273-1166
Fax: 51-1-273-1238
email: [email protected]
http://www.npiperu.com
Rexelca
Edif: Taburiente piso 1 ofic 1
Av Miranda Este # 93
Maracay, Aragua
Tel: 58-414-345-6047 / 58-243-232-1
Fax: 58-243-232-1563
email: [email protected]
Puerto Rico
PREMSCO
Calle Jordan 704
Santurce, PR 00909
Tel: 1-787-268-4040
Fax: 1-787-268-4006
email: [email protected]
http://www.premsco.com
Hi-Tech Products, Inc.
Ave. Sanchez Osorio
2MR-581 Villa Fontana
Carolina, PR 00983
Tel: 1-787-257-1707
Fax: 1-787-276-1888
email: [email protected]
http://www.hi-techproducts.com
Uruguay
Fidemar
Minas 1634-CP 11.200
Montevideo
Tel: 59-82-402-1717
Fax: 59-82-402-1719
email: [email protected]
http://www.fidemar.com.uy
More information online at
bannerengineering.com
iKNOW®
Wech Autocontroles, S.A.
Ave. Rómulo Betancourt 2158
Edificio WECH, Urb. Renacimiento
Santo Domingo, Dominican Republic
Tel: 809-531-0550
Fax: 809-531-9175
email: [email protected]
http://www.wechautocontroles.com.do
Venezuela
LAC Automation Industrial
Blvd. Lazaro Cardenas #770-6
Jardines Del Lago
Mexicali, B.C. 21330
Tel: 686-559-3509
Fax: 686-558-8383
email: [email protected]
CONTACT/SWITCHING
DIAGRAMS
Dominican Republic
ATD - Alta Tecnologia Digital
Boszues De Durango 85 LT 23 MZ XZI
Col. Jardines De Santa Monica
C.P. 54050 Tlalnepantla Edo. De Mexico
Tel: 55-5240-8000
Fax: 55-5565-0252
email: [email protected]
Vrumat Soluciones S.R.L.
Av. Del Plata M.38 S.16
Shangrila
Tel: 59-82-401-7076
Fax: 59-89-964-7391
email: [email protected]
HOOKUP
DIAGRAMS
Costa Rica
Tecnologia Interactiva
Recidencial Hacienda del Rey Casa 24C
Cartago CP: 1461-7050
Tel: 506-572-1102
Fax: 506-572-5664
email: [email protected]
http://www.tecnologiainteractiva.com
Alfa Automatizacíon
Ayuntamiento NO. 57 Dpt. 201
Int 202-203 Col. Centro
Delegacion Cuahutemoc
C.P. 06050
Tel: 55-8590-7610
Fax: 55-5601-7368
email: [email protected]íon.com
http://www.alfaautomatizacíon.com
Indicon
Calle 14 #806
Col. Centro
Chihuahua, Chihuahua 31020
Tel: 614-415-1051
Fax: 614-415-1061
email: [email protected]
GLOSSARY
Redes Eléctricas S.A.
Carrera 43A No. 14-109 of. 210
Medellín
Tel: 57-4-266-9791
Fax: 57-4-266-6787
email: [email protected]
AILDEM Automatizaciones
Internacionales de Mexico
Washington Nº2330 Pte
Colonia Maria Luisa
Monterrey, NL 64040
Tel: 81-8343-76633
Fax: 81-8343-1331
email: [email protected]
http://www.ail-us.com
INTERNATIONAL
REPRESENTATIVES
Redes Eléctricas S.A.
Calle 17 A No. 25-60
Santa Fe de Bogotá
Tel: 57-1-360-6299
Fax: 57-1-220-4600
email: [email protected]
271
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – INT. REPRESENTATIVES
Europe
Czech Republic
Turck s.r.o.
Hradecká 1151
CZ-50003 Hradec Králové 3
Tel: 420-495-518-766
Fax: 420-495-518-767
email: [email protected]
http://www.turck.cz
Denmark
CORPORATE OFFICE:
Banner Engineering Europe
Park Lane
Cullinganlaan 2F
Diegem
B-1831
Tel: 32-2-456-07-80
Fax: 32-2-456-07-89
email: [email protected]
http://www.bannereurope.com
Austria
Intermadox GmbH
Josef-Moser-Gasse 1
A-1170 Vienna
Tel: 431-48-61587
Fax: 431-48-6158723
email: [email protected]
http://www.intermadox.at
iKNOW®
Belarus
FEK Company
Industrial Automation Center
Pionerskaya Street 37A
Office 10 220020 Minsk
Tel: 375-17-2562917
Fax: 375-17-2562918
email: [email protected]
http://www.fek.by
INTERNATIONAL
REPRESENTATIVES
GLOSSARY
HOOKUP
DIAGRAMS
CONTACT/SWITCHING
DIAGRAMS
Belgium
Banner Engineering Europe
Park Lane
Cullinganlaan 2F
Diegem
B-1831
Tel: 32-2-456-07-80
Fax: 32-2-456-07-89
email: [email protected]
http://www.bannereurope.com
Multiprox N.V.
Lion d’Orweg, 12
B-9300 Aalst
Tel: 32-53-766 566
Fax: 32-53-783 977
email: [email protected]
http://www.multiprox.be
Bulgaria
Sensomat Ltd.
VH V, App 11
Dr. Ivan Penakov Str. 15
BG-9300 Dobrich
Tel: 359 58 603 023
Fax: 359 58 603 033
email: [email protected]
http://www.sensomat.info
272
More information online at
Hans Folsgaard AS
Theilgaards Torv 1
DK - 4600 Koge
Tel: 45-43-20-86-00
Fax: 45-43-96-88-55
email: [email protected]
http://www.hf.net
Estonia
Osaühing System Test
Pirita tee 20
EE-10127 Tallinn
Tel: 372-6-405-423
Fax: 372-6-405-422
email: [email protected]
Finland
Sarlin Oy Ab
P.O. Box 750
SF-00101 Helsinki 10
Tel: 358 (0)10-550-4200
Fax: 358 (0)10-550-4201
email: [email protected]
http://www.sarlin.com
Iceland
K M Stál ehf.
Bíldshöóa 16
110 Reykjavik
Tel: 354-56-78-939
Fax: 354-56-78-938
email: [email protected]
Ireland
Tektron
Tramore House
Tramore Road
Cork
Tel: 353 21-4313331
Fax: 353-21-4313371
email: [email protected]
http://[email protected]
Italy
Turck Banner s.r.l.
Via San Domenico, 5
20010 Bareggio
Milano
Tel: 390 2 90 36 42 91
Fax: 0039-2-90 36 48 38
email: [email protected]
http://www.turckbanner.it
Kazakhstan
Kazrosavtomatizaciya Sensorlink
Pacaeva st., 6 office 4-6
463020, Aktobe, Kazakhstan
Tel: +7 3132 563719
Fax: +7 3132 563719
email: [email protected]
http://www.sensorlink.ru
France
Turck Banner S.A.S.
3, Rue de Courtalin
Magny - Le - Hongre
77703 Marne - La - Vallée Cedex 4
Tel: 33-1-60-43-60-70
Fax: 33-1-60-43-10-18
email: [email protected]
http://www.turckbanner.fr
Germany
Hans Turck GmbH & Co KG
Witzlebenstrasse 7
45472 Mülheim an der Ruhr
Tel: 49-208-49-520
Fax: 49-208-49-52-264
email: [email protected]
http://www.turck.com
Greece
2KAPPA Ltd.
Stadiou 40
57009 Thessaloniki (Kalohori)
Tel: +30 2310 775512 / 2310 700812
Fax: +30 2310 775514
email: [email protected]
http://www.2kappa.gr
Hungary
Turck Hungary Kft.
Könyves Kalman Krt. 76
H-1087 Budapest
Tel: 36-1-477-0740 or 36-1-313-8221
Fax: 36-1-477-0741
email: [email protected]
http://www.turck.hu
Latvia
LASMA Ltd.
Aizkraukles 21-111
LV-1006 Riga
Tel: 371-754 5217
Fax: 371-754 5217
email: [email protected]
LEBANON
Industrial Technologies. S.A.L.
Industrial Bldg.
Main Road, Hbaline
Amchit
Tel: 961 1 448826
Fax: 961 9 635208
email: [email protected]
http://www.iteclb.com
Lithuania
Hidroteka
Büro: Taikos 76-4
LT-3031 Kaunas
Post: P.O. Box 572
LT-3028 Kaunas
Tel: 370-37 352195
Fax: 370-37-351952
email: [email protected]
Luxembourg
Sogel SA 1
7, Rue de l’Industrie
8399 Windhof
Tel: 352-40-05-05-331
Fax: 352-40-05-05-305
email: [email protected]
Netherlands/Holland
Turck B.V.
Ruiterlaan 7
NL-8019 BN Zwolle
Tel: 31-38-42-27-750
Fax: 31-38-42-27-451
email: [email protected]
http://www.turck.nl
Norway
Danyko A.S.
P.O. Box 48
N-4891 Grimstad
Tel: 47-37 090 940
Fax: 47-37 090 941
email: [email protected]
http://www.hf.net
Poland
Turck Sp. z o.o.
ul. Zeromskiego 1
50-053 Opole
Tel: 48-77 443 48 00
Fax: 48-77 443 48 01
email: [email protected]
http://www.turck.pl
Portugal
Salmon & Cia Lda.
Rua Cova da Moura, 2-6
Lisboa, 1350
Tel: 351-21-39 20 130
Fax: 351-21-39 20 189
email: [email protected]
Romania
TURCK Automation Romania SRL
Str. Iuliu Tetrat nr. 18
RO-011914 Bucharest
Tel: 40-21-230 02 79 or 40-21-230 0
Fax: 40-21-231 40 87
email: [email protected]
http://www.turck.ro
Russia and CIS
Sensorlink
Office Moskau
Volokolamskoe 1, Ofis 606 (v)
RU - 125080, Moscow
Tel: +7 (495) 9019164
email: [email protected]
http://www.sensorlink.ru
Sensorlink
Office Novosibirsk prospekt Krasny, 86
module 3, podjezd 2, office 503.
RU - 630005, Novosibirsk
Tel: +7 (383) 227-62-19
Fax: +7 (383) 227-62-45
email: [email protected]
http://www.sensorlink.ru
Sensorlink
Office Tolyatti
Komsomolskaya st., 18, office 7
RU -445010, Tolyatti
Tel: +7 8482 537594
Fax: +7 8482 537595
email: [email protected]
http://www.sensorlink.ru
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – INT. REPRESENTATIVES
Sensorlink
Office Sankt Petersburg
Naberegnaya Obrodnogo Kanala dom
193, Office 4-6
RU-190020, Saint-Petersburg
Tel: +7 (812) 331-1837
Fax: +7 (812) 331-1837
http://www.sensorlink.ru
Turck Rus OOO
Altufyevskoe Shosse 1/7
Moscow 127106
Tel: +7 4952342661
Fax: +7 4952352665
email: [email protected]
http://www.turk.ru
Turck Rus OOO
192012, Saint-Petersburg
prospect Obuxovskoi oboroni
dom 271 lit. А, office 647
Tel: +7-812-6333509
email: [email protected]
Turck Rus OOO - Novosibirsk
Tel: +7-913-9063305
email: [email protected]
Turck Rus OOO – Ekaterinburg
Tel: +7-912-6244220
email: [email protected]
Slovakia
Marpex s.r.o.
Sportovcov 672
018 41 Dubnica nad Váhom
Tel: 421 42 44269 86-87
Fax: 421 42 44400 10-11
email: [email protected]
http://www.marpex.sk
Spain
Elion, S.A.
Farell, 5
Vat. No. ESA08389587
E-08014 Barcelona
Tel: 34-932-982-000
Fax: 34-934-311-800
email: [email protected]
http://www.elion.es
Sweden
Turck Sweden
EA Rosengrensgata 32
421 31 Västra Frölunda
Tel: 46 31 471605
Fax: 46 31 471630
email: [email protected]
http:www.turk.se
Switzerland
UKRAINE
Bachofen AG
Ackerstrasse 42
8610 Uster
Tel: 41 44 944 11 11
Fax: 41 44 944 12 33
email: [email protected]
http://www.bachofen.ch
Sensorlink
Office Ukraine
S.-Shedrina st., 106, office 717
58029, Chirnivtsy
Tel: +38 0372 546760
Fax: +38 0372 546760
email: [email protected]
http://www.sensorlink.ru
Turkey
United Kingdom
Dacel Mühendislik Elektrik
Elektronik, San. Ve Tic. Ltd.
Perpa Elektrokent Is Merkezi
A Blok Kat 2 No: 38
Okmedani Istanbul
Tel: 90 212 210 7646
Fax: 90 212 220 5045
email: [email protected]
http://www.dacel.com.tr
Turck Banner Ltd.
Blenheim House
Hurricane Way, Wickford
Essex SS11 8YT
Tel: 44-0-1268-578888
Fax: 44-0-1268-763648
email: [email protected]
http://www.turckbanner.co.uk
Gökhan Elektrik Malzemeleri San
Tic Ltd Sti
Perpa Elektrokent iş Merkezi
A Blok Kat 8 No: 694
B4420 Okmeydani - Istanbul
Tel: 90-212-22 32 36
Fax: 90-212-221 32 40
email: [email protected]
http://www.gokhanelektrik.com.tr
HOOKUP
DIAGRAMS
CONTACT/SWITCHING
DIAGRAMS
Saudi Arabia
M.H. Sherbiny for Commerce
P.O. Box 3082
Prince Meshal Street, 2nd Street
Alkhobar 31952
Tel: 966-3-89-44-298
Fax: 966-3-86-47-278
email: [email protected]
http://www.sherbinyforcommerce.com
GLOSSARY
Israel
Robkon Industrial Control &
Automation Ltd.
12-A Elimelech St.
Ramat-gan, 52424
Tel: 972-3-673 28 21
Fax: 972-3-673 84 20
email: [email protected]
REP. of South Africa
RET Automation Controls Pty. Ltd.
130 Boeing Road East
Bedfordview, 2008
(shipping address)
P.O. Box 8378
Edenglen 1613 (mailing address)
Tel: 27-11-453 24 68
Fax: 27-11-453 24 06
email: [email protected]
http://www.retautomation.com
INTERNATIONAL
REPRESENTATIVES
Egypt
Egyptian Trading and Engineering
3, Hassan Sadek St.
Ouroba - Heliopolis Cairo
Tel: 20-2-290 83 80
Fax: 20-2-290 39 96
email: [email protected]
iKNOW®
Africa and Middle East
More information online at
bannerengineering.com
273
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – INT. REPRESENTATIVES
Asia, Australia and New Zealand
Banner Engineering Chengdu
Rm. D-1, 14th Flr., Chuanxin Mansion
No.18, Sec.2, Renming South Rd.
Chengdu 610016
Tel: 86-28-86200616
Fax: 86-28-86200618
email: [email protected]
http://www.bannerengineering.com.cn
Australia
Micromax Sensors and Automation
Pty Ltd (Headquarters)
5 Orange Grove Avenue
Unanderra NSW 2526
Tel: 61-24-271-13-00
Fax: 61-24-271-80-91
email: [email protected]
http://www.micromax.com.au
111 Arden St.
North Melbourne VIC 3051
Tel: 1300-36-26-26
Fax. 3-9329-5738
email: [email protected]
112 Beaconsfield St.
Auburn NSW 2144
Tel: 1300-36-26-26
Fax: 2-9648-3245
email: [email protected]
INTERNATIONAL
REPRESENTATIVES
GLOSSARY
HOOKUP
DIAGRAMS
CONTACT/SWITCHING
DIAGRAMS
iKNOW®
1/101 President St.
Carlisle WA 6101
Tel: 1300-36-26-26
Fax: 8-9470-5041
email: [email protected]
Suite 12/283 - 287
Sir Donald Bradman Drive
Brooklyn Park, S Australia 5032
Tel: 1300-36-26-26
Fax: 3-9329-5738
email: [email protected]
Banner Engineering Guangzhou
Room 2607/08
Huapu Plaza
No. 9 Huaming Road
Pearl River New City, Tianhe District
Guangzhou 510623
Tel: 86-20-28865171
Fax: 86-20-28865175
email: [email protected]
http://www.bannerengineering.com.cn
Banner Engineering Nanjing
Rm. B5, Flr. 6, Su Hua Commerce Bldg
No.178 ZhongShan (N) Rd
Nanjing 210009
Tel: 86-25-83362901
Fax: 86-25-83362901
email: [email protected]
http://www.bannerengineering.com.cn
Banner Engineering Tianjin
Room 3605D
Golden Crown Building, No.20
Nanjing Road, Hexi District
Tianjin 300041
Tel: 86-22-23133420
Fax: 86-22-23133425
email: [email protected]
http://www.bannerengineering.com.cn
Banner Engineering Shenzhen
Rm. 15C, Building B, Fortune Plaza,
No. 7060 ShenNan Road
Shenzhen
Tel: 86-755-83022293
Fax: 86-755-83022291
email: [email protected]
http://www.bannerengineering.com.cn
Banner Engineering Suzhou
Building 49
Chuangtou District
He Shun Road, North of Loufeng
Suzhou Industry Park, Suzhou 215122
Tel: +86 512 6274 5997
Temtrol Technologies, 108 Victoria Street Fax: +86 512 6274 5993
George Town, Tas. 7253
email: [email protected]
Tel: 3-6382-4144
http://www.bannerengineering.com.cn
Fax: 3-6382-4134
Sentec P/L, 2/35 Ethel St
Yeerongpilly, QLD 4105
Tel: 7-3848-1144
Fax: 7-3848-1344
China
Banner Engineering Shanghai
Room 28 G/H/I 28th Flr.
Cross Region Plaza
No. 889, Lingling Road
Shanghai 200030
Tel: 86-21-54894500
Fax: 86-21-54894511
email: [email protected]
http://www.bannerengineering.com.cn
Banner Engineering Beijing
Rm 11C2, Tower 2, Xihuan Plaza
No.1, Xiwai Street, Xicheng District
Beijing 100044
Tel: 86-10-58301588/58301565
Fax: 86-10-58301566
email: [email protected]
http://www.bannerengineering.com.cn
274
Banner Engineering Qingdao
Room 10J
Wang Jiao Building, No.73
Central Hong Kong Road
Qingdao, 266071
Tel: 86-532-86128366
Fax: 86-532-86128369
email: [email protected]
http://www.bannerengineering.com.cn
Hong Kong
Banner Engineering Hong Kong
Rm. 15C, Building B, Fortune Plaza
No. 7060 ShenNan Rd, Shenzhen
Tel: 86-755-83022293
Fax: 86-755-83022291
email: [email protected]
http:/www.bannerengineering.com.cn
More information online at
India
Banner Engineering India Pvt. Ltd.
Office No. 1001
Sai Capital, Opp. ICC
Senapati Bapat Road
Pune 411016
Tel: 91-(0)20-66405624
Fax: 91-(0)20-66405623
email: [email protected]
http://www.bannerengineering.co.in
Banner Engineering India (New Delhi)
44, Sector 11, Pocket - 2
DDA SFS Flates
Dwarka, New Delhi 110075
Tel: 91-9313510345
Fax: 91-11-28042748
email: [email protected]
http://www.bannerengineering.com.in
Banner Engineering India (Chennai)
Plot No. 43, Swami Malai Street
Arul Murugan Nagar
Kilkattalai Chennai - 600 117
Tel: 91-9380407838
Fax: 91-44-22477698
email: [email protected]
http://www.bannerengineering.com.in
Banner Engineering India (Bangalore)
C/O Narayana Shettinagar, A3, Flat No. 405
Sneha Apartment, Godavari Block,
National Games Village, Karmangala,
Bangalore, Karnatakka
Tel: 9379141892
Email: [email protected]
http://www.bannerengineering.co.in
Morimura Brothers Inc.
Morimura Building
1-3-1 Toranomon
Minato-ku, Tokyo 105-8451
Tel: 81-3-3502-6449
Fax: 81-3-3593-3376
http://www.morimura.co.jp
Korea
Turck Korea
Room 406, Gyeonggi Technopark
1271-11, Sai-Dong
Sangnok-Gu, Ansan
Gyeonggi-Do 426-901
Tel: 82 31 500 4555
Fax: 82 31 500 4558
email: [email protected]
http://www.sensor.co.kr
K & S Korea Co., Ltd.
306 Office A-Dong, Chungan
Circulation Complex 1258
Gurobon-Dong, Guro-Gu
Seoul
Tel: 82-22-619-0244
Fax: 82-22-619-0243
Malaysia
UST Technology Pte. Ltd.
998 Toa Payoh North
#5 - 25
Singapore 318993
Tel: 65-6252-2272
Fax: 65-6253-8773
email: [email protected]
http://www.ust.com.sg
Banner Engineering India (Jamshedpur)
62, M.I.G., Sangam Vihar,
New Zealand
Near Sonari, Jamshedpur – 831011
W.
Arthur
Fisher Ltd.
Tel: 9308741856
Email: [email protected] 15 Polaris Place
East Tamaki, 2013
http://www.bannerengineering.co.in
Auckland
Tel: 64-9-27 00 100
Fax: 64-9-27 00 900
Indonesia
email: [email protected]
Pt. Unitama Sentosa Gemilang
http://www.waf.co.nz
Kompleks Permata Ancol Blok N, no. 32
Jl. R.E. Martadinata
Jakarta Utara 14420
Philippines
Tel: 62-21-645-1132
Fax: 62-21-645-1130
UST Technology Pte. Ltd.
email: [email protected]
998 Toa Payoh North
http://www.unitama.co.id
#5 - 25
Singapore 318993
Tel: 65-6252-2272
Japan
Fax: 65-6253-8773
email: [email protected]
Banner Engineering Japan
http://www.ust.com.sg
Cent-Urban Building 305
3-23-15 Nishi-Nakajima
Yodogawa-Ku, Osaka 532-0011
Singapore
Tel: 81-6-6309-0411
Fax: 81-6-6309-0416
UST Technology Pte. Ltd.
998 Toa Payoh North
Japan Machinery Company
#5 - 25
Nakajima Shoji Building 8F
Singapore 318993
8-5-6 Ginza
Tel: 65-6252-2272
Chuo-ku, Tokyo 104-0061
Fax: 65-6253-8773
Tel: 81-3-3573-5421
email: [email protected]
Fax: 81-3-3574-9185
http://www.ust.com.sg
email: [email protected]
http://www.japanmachinery.com
Koyo Electronics Industries Co.
1-171 Tenjin-cho
Kodaira, Tokyo 187-0004
Tel: 81-42-341-3114
Fax: 81-42-341-3118
email: [email protected]
http://www.koyoele.co.jp
Sri Lanka
I.Q. Systems (PVT) Ltd.
35A 1/1, Sunethradevi Road
Kohuwala, Nugegoda
Tel: 0094-112-769-969
Fax: 0094-112-826-807
email: [email protected] or
[email protected]
bannerengineering.com
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
REFERENCE – INT. REPRESENTATIVES
Thailand
GLOSSARY
HOOKUP
DIAGRAMS
CONTACT/SWITCHING
DIAGRAMS
iKNOW®
Compomax Company Limited
16 Soi Ekamai 4, Sukhumvit 63 Rd.
Prakanongnua, Vadhana
Bangkok 10110
Tel: 66-2-726-9595
Fax: 66-2-726-9800
email: [email protected]
http://www.compomax.co.th
INTERNATIONAL
REPRESENTATIVES
Taiwan
Banner Engineering Taiwan
Neihu Technology Park
5F-1 No. 51 Lane 35 Jihu Rd
Taipei 114
Tel: 886-2-8751-9966
Fax: 886-2-8751-2966
email: [email protected]
http://www.bannerengineering.com.tw
More information online at
bannerengineering.com
275
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
INDEX
Model
11-BG00-31-A12060
11-BG00-31-D-024
11-BGX10-40
11-BGX77-048
11-BGX77-240
11-G318-48
11-G484-30
8-L2PP-1A5
8-LM2T-AU115
8-LM2T-AU120
8-LM2T-B6644
8-LM2T-C01
8-LM2T-C10
8-LP2T-B6644
AG4-4E
AG4A-SW-A
AG4-CLN1
AG4-CLN2
AG4-CPD15
AG4-CPD15-10
AG4-CPD15-10RA
AG4-CPD15-25
AG4-CPD15-5
AG4-CPD15-50
AG4-CPD15-RA
AG4-CPD9
AG4-MBK1
AG4-PCD9-10
AG4-PCD9-3
AG4-PCD9-5
AG4-PCD9-RA
AG4-TB1
AG4-WIN
AT-AM-2A
AT-AM-K5
AT-AM-K5Q
AT-BM-2A
AT-BM-K5
AT-BM-K5Q
AT-FM-10K
AT-FM-2A
AT-FM-K6
AT-FM-K6Q
AT-FM-K81
AT-FM-K81Q
AT-GM-11KM
AT-GM-13A
ATGMKM-VP6
ATGMKM-VP6Q
ATGMKM-VP6Q5
ATGMK-VP6
ATGMK-VP6Q
ATGMK-VP6Q5
ATGMK-VR81
ATGMK-VR81Q
ATGMK-VR81Q6
AT-HM-11KM
AT-HM-13A
ATHMKM-VP6
ATHMKM-VP6Q
ATHMKM-VP6Q5
ATHMK-VP6
ATHMK-VP6Q
ATHMK-VP6Q5
ATHMK-VR81
ATK-VP6
ATK-VP6Q
ATK-VP6Q5
BF1801A-12060
BF1801L-024
BFX77-240
CSB-M1240M1240
CSB-M12415M1241
CSB-M1241M1241
CSB-M12425M1241
CSB-M1248M1241
CSB-M1280M1280
CSB-M12815M1281
CSB-M1281M1281
CSB-M12825M1281
CSB-M1288M1281
CSB-UNT425M1241
CSB-UNT825M1281
DEC2-5100
DEC2-515C
DEC2-525C
DEC2-550C
DEC2-575
DEC-540C
DEC-550C
DEC-570
DEE2R-5100D
DEE2R-515D
DEE2R-51D
DEE2R-525D
DEE2R-53D
DEE2R-550D
DEE2R-575D
276
Part #
69681
69682
69685
69683
69684
69689
69688
69698
69697
69696
69691
69693
69695
69692
82137
144088
82155
82156
82151
82143
82146
82144
82142
82145
82153
82152
82139
82149
82147
82148
82154
82141
82138
49390
49777
49778
72052
49779
49780
60698
72050
49781
49782
49783
49784
02897
66089
71688
71689
71690
68275
68276
79611
02992
71977
78378
02898
66090
71691
71692
71693
68277
68278
70396
78407
64290
64291
64292
81162
81263
81163
64206
75275
75273
75276
75274
75375
73254
73252
73255
73253
75277
73256
62797
62793
62794
62795
62796
52369
47362
52365
72339
72335
72333
72336
72334
72337
72338
Pg Ref.
191
191
191
191
191
191
191
154
154
154
154
154
154
154
54
56
56
56
56
185
185
185
185
185
56
56
166
185
185
185
56
56
56
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
112
w.o.
w.o.
w.o.
w.o.
w.o.
112
112
113
113
113
113
113
113
w.o.
w.o.
w.o.
112
112
113
113
113
113
113
113
w.o.
113
113
113
191
191
191
178
178
178
178
178
180
180
180
180
180
178
180
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
179
179
179
179
179
179
179
“w.o” indicates web only; visit
Model
DEE2R-58D
DEE2R-8100D
DEE2R-815D
DEE2R-81D
DEE2R-825D
DEE2R-83D
DEE2R-850D
DEE2R-875D
DEE2R-88D
DELP-110E
DELP-110EB
DELP-11100E
DELP-11100EB
DELP-1115E
DELP-1115EB
DELP-111E
DELP-111EB
DELP-1125E
DELP-1125EB
DELP-113E
DELP-113EB
DELP-1150E
DELP-1150EB
DELP-1175E
DELP-1175EB
DELP-118E
DELP-118EB
DELPE-8100D
DELPE-8100DB
DELPE-815D
DELPE-815DB
DELPE-81D
DELPE-81DB
DELPE-825D
DELPE-825DB
DELPE-83D
DELPE-83DB
DELPE-850D
DELPE-850DB
DELPE-875D
DELPE-875DB
DELPE-88D
DELPE-88DB
DELPEF-81D
DELPEF-81DB
DES4-508C
DES4-515C
DES4-525C
DESE4-508D
DESE4-515D
DESE4-525D
DESE5-508D
DESE5-515D
DESE5-525D
DEU-515C
DEU-525C
DIN-35-105
DIN-35-140
DIN-35-70
EM-F-7G
EM-FD-7G2
EM-FD-7G3
EM-FD-7G4
EM-T-7A
ES-FA-11AA
ES-FA-6G
ES-FA-9A
ES-FA-9AA
ES-FL-2A
ESL-30/60-1
ESL-30/60-10
ESL-30/75-10
ESL-38/60-10
ESL-38/75-10
ESL-38/90-10
ESL-46/70-10
ESL-46/70-25
ESL-46/80-10
ESL-46/90-10
ES-TA-3D1
ES-TA-3F1
ES-TN-14H5
ES-TN-14H6
ES-TN-1H1
ES-TN-1H10
ES-TN-1H11
ES-TN-1H12
ES-TN-1H2
ES-TN-1H3
ES-TN-1H4
ES-TN-1H5
ES-TN-1H6
ES-TN-1H7
ES-TN-1H8
ES-TN-1H9
ES-UA-5A
ES-VA-5A
EZA-ADE-1
Part #
72636
72211
72207
72205
72208
72206
72209
72210
72635
80802
82791
80810
82799
80806
82795
80803
82792
80807
82796
80804
82793
80808
82797
80809
82798
80805
82794
80818
82807
80814
82803
80811
82800
80815
82804
80812
82801
80816
82805
80817
82806
80813
82802
82816
82815
69019
69020
69021
71400
71401
71402
74830
74831
74832
50068
50069
30470
26605
26604
55750
55785
55723
55724
52402
02628
55579
52404
60131
46092
75186
73642
73643
72736
72737
72738
72731
72732
72733
72734
50669
53412
68423
68437
72667
61068
61069
61070
61062
61063
61064
57481
59648
61065
61066
61067
66091
66092
71447
bannerengineering.com
Pg Ref.
179
180
180
180
180
180
180
180
180
182
182
182
182
182
182
182
182
182
182
182
182
182
182
182
182
182
182
181
181
181
181
181
181
181
181
181
181
181
181
181
181
181
181
182
182
188
188
188
188
188
188
188
188
188
w.o.
w.o.
166
166
166
106
106
106
106
106
82
82
w.o.
82
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
82
82
82
82
82
82
82
82
82
82
82
82
82
82
82
82
28
Model
EZA-ADE-2
EZA-ADE-3
EZA-ADE-4
EZA-ADR-1
EZA-ADR-2
EZA-ADR-3
EZA-ADR-4
EZA-AP-1
EZAC-E-QE5
EZAC-E-QE5-QS5
EZAC-E-QE8
EZAC-E-QE8-QS3
EZA-CP-13
EZAC-R10N-QE8-QS53
EZAC-R11-QE8
EZAC-R15A-QE8-QS83
EZAC-R8N-QE8-QS53
EZAC-R9-QE8
EZAC-RM-1
EZAC-RM-2
EZA-ECE-1
EZA-ECR-1
EZA-LAT-1
EZA-LAT-2
EZA-LAT-SS
EZA-MBK-1
EZA-MBK-11
EZA-MBK-11N
EZA-MBK-12
EZA-MBK-2
EZA-MBK-20
EZA-MBK-20U
EZA-MBK-21
EZA-MBK-3
EZA-MBK-4
EZA-MBK-5
EZA-MBK-9
EZA-QDE-3
EZA-QDE-5
EZA-QDE-8E
EZA-QDR-8
EZA-QDR-8E
EZA-S300
EZA-S300-M
EZA-S400
EZA-S400-M
EZA-S500
EZA-S500-M
EZA-S500-M45
EZA-S533
EZA-S533-M
EZA-S584
EZA-S584-M
EZA-S584-M45
EZA-SW-1
EZA-TBE-1
EZA-TBR-1
EZA-TE-1050
EZA-TE-1200
EZA-TE-1350
EZA-TE-150
EZA-TE-1500
EZA-TE-1650
EZA-TE-1800
EZA-TE-300
EZA-TE-450
EZA-TE-600
EZA-TE-750
EZA-TE-900
EZA-TE-BEC
EZA-TP-1
EZA-TP-1N
EZS-1050
EZS-1084
EZS-1200
EZS-1251
EZS-1350
EZS-149
EZS-150
EZS-1500
EZS-1650
EZS-1800
EZS-300
EZS-450
EZS-600
EZS-684
EZS-750
EZS-768
EZS-900
EZS-984
EZSS-1050
EZSS-1200
EZSS-1350
EZSS-150
EZSS-1500
EZSS-1650
EZSS-1800
EZSS-300
Part #
72929
73638
73640
71448
72930
73639
73641
62859
74321
73466
74320
73465
62860
73302
73761
74115
73303
73300
73995
73996
62858
62857
66027
71446
73318
60630
71470
75253
71756
61947
72587
81369
73319
61980
61981
61982
66013
68475
68476
76513
68474
76514
70446
70447
70448
70449
70450
70451
70452
70453
70454
70455
70456
70457
62863
62861
62862
72796
72797
72798
72790
72799
72800
72801
72791
72792
72793
72794
72795
80764
71449
75252
71458
61953
71459
61952
71460
61948
71452
71461
71462
71463
71453
71454
71455
61949
71456
61950
71457
61951
76073
76074
76075
76067
76076
76077
76078
76068
Pg Ref.
28
w.o.
w.o.
28
28
w.o.
w.o.
48
189
189
189
189
48
189
189
189
189
189
w.o.
w.o.
48
48
197
197
w.o.
166
166
w.o.
167
167
167
w.o.
167
168
168
168
168
186
186
w.o.
186
w.o.
202
202
202
202
202
202
202
22
202
202
202
202
48
48
48
201
201
201
201
201
201
201
201
201
201
201
201
w.o.
28
w.o.
200
199
200
199
200
199
200
200
200
200
200
200
200
199
200
199
200
199
200
200
200
200
200
200
200
200
“call” indicates call 1-888-373-6767
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
INDEX
Model
EZSS-450
EZSS-600
EZSS-750
EZSS-900
FIC-M12F4
FIC-M12F4A
FIC-M12M4
FIC-M12M4A
GM-FA-10J
GMMSE2424YP
GMMSE424Y
GMMSR2424YP
GMMSR424Y
GMSLSCE30-1200Q8
GMSLSCE30-1350Q8
GMSLSCE30-1800Q8
GMSLSCE30-600Q8
GMSLSCP14-1200Q88
GMSLSCP14-300Q88
GMSLSCP30-1800Q88
GMSLSCR30-1200Q8
GMSLSCR30-1350Q8
GMSLSCR30-1800Q8
GMSLSCR30-600Q8
GMSLSE30-1200Q8
GMSLSE30-600Q8
GMSLSE30-900Q8
GMSLSP30-1200Q88
GMSLSR30-1200Q8
GMSLSR30-600Q8
GMSLSR30-900Q8
IM-T-11A
IM-T-9A
K30LRGX8PQ8
K50LGRYB11P
K50LRGX8PQ8
K80LRGX8PQ8
LAT-1
LAT-1-HD
LAT-1-LP
LAT-1-LS
LAT-1-MS
LAT-1-SFP12
LAT-1-SFP30
LAT-1-SS
LAT-1-US
LPA-LAT-1
LPA-MBK-11
LPA-MBK-12
LPA-MBK-120
LPA-MBK-13
LPA-MBK-135
LPA-MBK-180
LPA-MBK-20
LPA-MBK-21
LPA-MBK-22
LPA-MBK-90
LPA-TP-1
LS2E30-1050Q8
LS2E30-1200Q8
LS2E30-1350Q8
LS2E30-1500Q8
LS2E30-150Q8
LS2E30-1650Q8
LS2E30-1800Q8
LS2E30-300Q8
LS2E30-450Q8
LS2E30-600Q8
LS2E30-750Q8
LS2E30-900Q8
LS2LK30-450Q88-1RE50
LS2LK30-450Q88-2RE15
LS2LK30-750Q88-1RE15
LS2LK30-750Q88-2RE15
LS2LK30-900Q88-1RE15
LS2LK30-900Q88-2RE15
LS2LP30-1050Q88
LS2LP30-1200Q88
LS2LP30-1350Q88
LS2LP30-1500Q88
LS2LP30-150Q88
LS2LP30-1650Q88
LS2LP30-1800Q88
LS2LP30-300Q88
LS2LP30-450Q88
LS2LP30-600Q88
LS2LP30-750Q88
LS2LP30-900Q88
LS2LR30-1050Q8
LS2LR30-1200Q8
LS2LR30-1350Q8
LS2LR30-1500Q8
LS2LR30-150Q8
LS2LR30-1650Q8
LS2LR30-1800Q8
LS2LR30-300Q8
LS2LR30-450Q8
LS2LR30-600Q8
Part #
76069
76070
76071
76072
58912
58913
58910
58911
60987
79284
77520
79285
77061
79639
79641
79643
79635
77134
77396
77961
79640
79642
79644
79636
79705
79633
79637
79704
79706
79634
79638
61424
61425
78790
77389
76000
78085
52150
71444
83816
73745
71442
71847
72999
71445
71443
83817
82841
82842
82847
82843
82848
82849
82853
82845
82844
82846
82840
73530
73531
73532
73533
73524
77248
77249
73525
73526
73527
73528
73529
79774
77288
81052
77944
80785
81586
73570
73571
73572
73573
73564
77256
77257
73565
73566
73567
73568
73569
73560
73561
73562
73563
73554
77252
77253
73555
73556
73557
Pg Ref.
200
200
200
200
w.o.
w.o.
188
188
82
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
108
108
192
192
192
192
197
197
197
197
w.o.
197
197
197
w.o.
197
169
169
169
w.o.
169
170
170
170
170
171
36
40
40
40
40
40
w.o.
w.o.
40
40
40
40
40
41
41
41
41
41
41
40
40
40
40
40
w.o.
w.o.
40
40
40
40
40
40
40
40
40
40
w.o.
w.o.
40
40
40
“w.o” indicates web only; visit
Model
LS2LR30-750Q8
LS2LR30-900Q8
LS2TK30-1200Q88-2RE25
LS2TK30-1500Q88-2RE25
LS2TK30-150Q88-1RE15
LS2TK30-150Q88-2RE25
LS2TK30-300Q88-1RE25
LS2TK30-300Q88-1RE50
LS2TK30-300Q88-2RE15
LS2TK30-300Q88-2RE25
LS2TK30-450Q88-1RE25
LS2TK30-450Q88-2RE25
LS2TK30-600Q88-1RE15
LS2TK30-600Q88-2RE25
LS2TK30-750Q88-1RE15
LS2TK30-750Q88-1RE50
LS2TK30-900Q88-1RE100
LS2TK30-900Q88-1RE15
LS2TK30-900Q88-1RE25
LS2TK30-900Q88-1RE50
LS2TK30-900Q88-2RE25
LS2TK30-900Q88-2RE75
LS2TP30-1050Q88
LS2TP30-1200Q88
LS2TP30-1350Q88
LS2TP30-1500Q88
LS2TP30-150Q88
LS2TP30-1650Q88
LS2TP30-1800Q88
LS2TP30-300Q88
LS2TP30-450Q88
LS2TP30-600Q88
LS2TP30-750Q88
LS2TP30-900Q88
LS2TR30-1050Q8
LS2TR30-1200Q8
LS2TR30-1350Q8
LS2TR30-1500Q8
LS2TR30-150Q8
LS2TR30-1650Q8
LS2TR30-1800Q8
LS2TR30-300Q8
LS2TR30-450Q8
LS2TR30-600Q8
LS2TR30-750Q8
LS2TR30-900Q8
LSA-LAT-1
LSA-LAT-2
LSS-1050
LSS-1200
LSS-1350
LSS-150
LSS-1500
LSS-300
LSS-450
LSS-600
LSS-750
LSS-900
M18RGX8PQ8
M18RGR5PNQ
MBCC-406
MBCC-415
MBCC-430
MBCC-506
MBCC-515
MBCC-530
MDSA-PTB-1
MDSA-PTB-2
MDSDAB-1
MDSDAL-1
MDSDA-RM-1
MDSDINT-1L2
MDSDINT-1T2
MGA-12-CA
MGA-54-CA
MGA-60-CA
MGA-66-CA
MGA-6-CA
MGA-72-CA
MGAB-4
MGAB-5
MGA-GS-1
MGA-GST-1
MGA-K-1
MGA-KS-1
MGA-KSO-1
MGA-LP-1
MGA-LR-1
MGA-LRKS-1
MGA-RC-1
MGA-RMFSD
MGA-RMSSD
MGA-S72-1
MGA-SBFS-2
MGA-SPB-1
MGA-STP-1
MGA-TBA4-1
MGA-TBA5-1
Part #
73558
73559
77296
77305
79142
77295
78527
79604
80063
77297
80711
77294
77526
78529
81701
79605
79768
81702
80744
79606
77293
77279
73550
73551
73552
73553
73544
77254
77255
73545
73546
73547
73548
73549
73540
73541
73542
73543
73534
77250
77251
73535
73536
73537
73538
73539
73746
73747
73754
73755
73756
73748
73757
73749
73750
73751
73752
73753
74027
74368
45134
25226
29951
32297
25496
29950
61083
61084
48226
65785
48225
45327
45325
29380
34399
31574
34400
29379
31575
30701
30700
27850
28511
28513
28509
30140
28508
29769
29770
28510
33629
33630
30125
29957
35623
28518
34067
34068
bannerengineering.com
Pg Ref.
40
40
41
41
41
41
41
41
41
41
41
41
41
41
41
41
41
41
41
41
41
41
40
40
40
40
40
w.o.
w.o.
40
40
40
40
40
40
40
40
40
40
w.o.
w.o.
40
40
40
40
40
197
w.o.
200
200
200
200
200
200
200
200
200
200
192
193
183
183
183
184
184
184
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
28
w.o.
28
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
Model
MGA-VM-1
MGCA-4A
MGCA-5A
MGCB-4A
MGCB-5A
MGE1216A
MGE1816A
MGE2416A
MGE3016A
MGE3616A
MGE4216A
MGE4816A
MGE5416A
MGE6016A
MGE616A
MGE6616A
MGE7216A
MGR1216A
MGR1816A
MGR2416A
MGR3016A
MGR3616A
MGR4216A
MGR4816A
MGR5416A
MGR6016A
MGR616A
MGR6616A
MGR7216A
MGS12A
MGS18A
MGS24A
MGS30A
MGS36A
MGS42A
MGS48A
MGS54A
MGS60A
MGS66A
MGS6A
MGS72A
MM2-TA-12B
MMD-TA-11B
MMD-TA-12B
MM-TA-12B
MQDC1-501.5
MQDC1-506
MQDC1-506RA
MQDC1-515
MQDC1-515RA
MQDC1-530
MQDC1-530RA
MQDC-406
MQDC-406RA
MQDC-415
MQDC-415RA
MQDC-430
MQDC-430RA
MQDC-450
MQDC-450RA
MQDEC-403RS
MQDEC-403SS
MQDEC-406RS
MQDEC-406SS
MQDEC-412RS
MQDEC-412SS
MQDEC-420RS
MQDEC-420SS
MQDEC-430RS
MQDEC-430SS
MQDEC-450RS
MQDEC-450SS
MQDMC-406
MQDMC-406RA
MQDMC-415
MQDMC-415RA
MQDMC-430
MQDMC-430RA
MQDMC-450
MQDMC-450RA
MQEAC-406
MQEAC-406RA
MQEAC-415
MQEAC-415RA
MQEAC-430
MQEAC-430RA
MQEAC-606
MQEAC-606RA
MQEAC-615
MQEAC-615RA
MQEAC-630
MQEAC-630RA
MSAB-1
MSAB-2
MSA-KS-1
MSAL-1
MSA-LAT-2
MSAMB
Part #
28514
34048
34049
34050
34051
27749
27824
27750
27825
27751
27826
27752
33012
30264
27823
33014
29746
32174
32175
32176
32177
32178
32179
32180
33013
32181
32182
33015
32300
29377
29401
29402
29403
29404
29405
29406
33555
29982
33556
29376
29917
74934
75090
75091
63516
71038
51127
51128
47812
47813
47814
47815
45136
47104
26850
26848
27142
27080
33649
49213
47456
47631
47457
47632
47458
47633
47459
47634
78626
72154
78628
76602
02780
70899
02781
70900
02954
70967
call
70971
75291
75294
75292
75295
75293
75296
77319
77322
77320
77323
77321
77324
39029
47381
39023
55695
54302
43152
“call” indicates call 1-888-373-6767
Pg Ref.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
95
95
95
95
178
178
178
178
178
178
178
177
177
177
177
177
177
177
177
177
177
177
177
177
177
177
177
177
177
177
177
177
177
177
177
177
177
177
177
182
182
182
182
182
182
182
183
183
183
183
183
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
277
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
INDEX
Model
MSA-MBM-K45
MSA-MH-1
MSA-PMS-30
MSA-PMS-42
MSA-PMS-54
MSA-PSA-1
MSA-PSA-2
MSA-PSB-1
MSA-PSD-1
MSA-PSD-2
MSA-PST-1
MSA-PST-2
MSA-PTB-1
MSA-PTB-2
MSA-RM-1
MSA-RM-2
MSA-S105-1
MSA-S105-1NB
MSA-S24-1
MSA-S24-1NB
MSA-S42-1
MSA-S42-1NB
MSA-S66-1
MSA-S66-1NB
MSA-S84-1
MSA-S84-1NB
MSA-SB-1
MSA-TE-12
MSA-TE-16
MSA-TE-20
MSA-TE-24
MSA-TE-28
MSA-TE-32
MSA-TE-36
MSA-TE-4
MSA-TE-40
MSA-TE-44
MSA-TE-48
MSA-TE-8
MSCA-1
MSCA-1L2
MSCA-1L3
MSCA-1L3E
MSCA-1S23
MSCA-1S3E
MSCA-1T3
MSCB-1
MSCB-1L2
MSCB-1T3
MSCC-2L2M
MSCC-2L3M
MSCC-2T2M
MSCC-2T3M
MSCD-2
MSCD-2T3
MSCT-1
MSCT-1T3
MSCT-2
MSCT-2T3
MSDAB-1
MSDAL-1
MSDA-RM-1
MSDINT-1
MSDINT-1L2
MSDKT1224C1
MSDKT1224C1Y
MSDKT1224C2
MSDKT1224C2Y
MSDKT1224C3
MSDKT1224C3Y
MSDKT1224LC1
MSDKT1224LC1Y
MSDKT1224LC2
MSDKT1224LC2Y
MSDKT1224LC3
MSDKT1224LC3Y
MSDKT1624C1
MSDKT1624C1Y
MSDKT1624C2
MSDKT1624C2Y
MSDKT1624C3
MSDKT1624C3Y
MSDKT1624LC1
MSDKT1624LC1Y
MSDKT1624LC2
MSDKT1624LC2Y
MSDKT1624LC3
MSDKT1624LC3Y
MSDKT2024C1
MSDKT2024C1Y
MSDKT2024C2
MSDKT2024C2Y
MSDKT2024C3
MSDKT2024C3Y
MSDKT2024LC1
MSDKT2024LC1Y
MSDKT2024LC2
MSDKT2024LC2Y
278
Part #
58857
39024
64251
64252
64250
39027
55694
39028
61499
47377
43738
47376
61077
61078
39025
59689
79123
79124
43174
43177
43175
43178
43176
43179
52397
55650
57116
70436
70437
70438
70439
70440
46906
70442
70434
70443
70444
70445
70435
37931
55692
68389
69842
64719
69323
59692
37932
61996
59693
62041
62838
65050
64775
45707
60126
43536
70499
45711
65153
45281
48450
45280
44469
47699
45202
46046
45214
46058
45226
46070
47702
47738
47714
47750
47726
47762
45203
46047
45215
46059
45227
46071
47703
47739
47715
47751
47727
47763
45204
46048
45216
46060
45228
46072
47704
47740
47716
47752
Pg Ref.
171
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
198
198
198
198
198
198
198
198
198
198
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
“w.o” indicates web only; visit
Model
MSDKT2024LC3
MSDKT2024LC3Y
MSDKT2424C1
MSDKT2424C1Y
MSDKT2424C2
MSDKT2424C2Y
MSDKT2424C3
MSDKT2424C3Y
MSDKT2424LC1
MSDKT2424LC1Y
MSDKT2424LC2
MSDKT2424LC2Y
MSDKT2424LC3
MSDKT2424LC3Y
MSDKT2824C1
MSDKT2824C1Y
MSDKT2824C2
MSDKT2824C2Y
MSDKT2824C3
MSDKT2824C3Y
MSDKT2824LC1
MSDKT2824LC1Y
MSDKT2824LC2
MSDKT2824LC2Y
MSDKT2824LC3
MSDKT2824LC3Y
MSDKT3224C1
MSDKT3224C1Y
MSDKT3224C2
MSDKT3224C2Y
MSDKT3224C3
MSDKT3224C3Y
MSDKT3224LC1
MSDKT3224LC1Y
MSDKT3224LC2
MSDKT3224LC2Y
MSDKT3224LC3
MSDKT3224LC3Y
MSDKT3624C1
MSDKT3624C1Y
MSDKT3624C2
MSDKT3624C2Y
MSDKT3624C3
MSDKT3624C3Y
MSDKT3624LC1
MSDKT3624LC1Y
MSDKT3624LC2
MSDKT3624LC2Y
MSDKT3624LC3
MSDKT3624LC3Y
MSDKT4024C1
MSDKT4024C1Y
MSDKT4024C2
MSDKT4024C2Y
MSDKT4024C3
MSDKT4024C3Y
MSDKT4024LC1
MSDKT4024LC1Y
MSDKT4024LC2
MSDKT4024LC2Y
MSDKT4024LC3
MSDKT4024LC3Y
MSDKT424C1
MSDKT424C1Y
MSDKT424C2
MSDKT424C2Y
MSDKT424C3
MSDKT424C3Y
MSDKT424LC1
MSDKT424LC1Y
MSDKT424LC2
MSDKT424LC2Y
MSDKT424LC3
MSDKT424LC3Y
MSDKT4424C1
MSDKT4424C1Y
MSDKT4424C2
MSDKT4424C2Y
MSDKT4424C3
MSDKT4424C3Y
MSDKT4424LC1
MSDKT4424LC1Y
MSDKT4424LC2
MSDKT4424LC2Y
MSDKT4424LC3
MSDKT4424LC3Y
MSDKT4824C1
MSDKT4824C1Y
MSDKT4824C2
MSDKT4824C2Y
MSDKT4824C3
MSDKT4824C3Y
MSDKT4824LC1
MSDKT4824LC1Y
MSDKT4824LC2
MSDKT4824LC2Y
MSDKT4824LC3
MSDKT4824LC3Y
Part #
47728
47764
45205
46049
45217
46061
45229
46073
47705
47741
47717
47753
47729
47765
45206
46050
45218
46062
45230
46074
47706
47742
47718
47754
47730
47766
45207
46051
45219
46063
45231
46075
47707
47743
47719
47755
47731
47767
45208
46052
45220
46064
45232
46076
47708
47744
47720
47756
47732
47768
45209
46053
45221
46065
45233
46077
47709
47745
47721
47757
47733
47769
45200
46044
45212
46056
45224
46068
47700
47736
47712
47748
47724
47760
45210
46054
45222
46066
45234
46078
47710
47746
47722
47758
47734
47770
45211
46055
45223
46067
45235
46079
47711
47747
47723
47759
47735
47771
bannerengineering.com
Pg Ref.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
Model
MSDKT824C1
MSDKT824C1Y
MSDKT824C2
MSDKT824C2Y
MSDKT824C3
MSDKT824C3Y
MSDKT824LC1
MSDKT824LC1Y
MSDKT824LC2
MSDKT824LC2Y
MSDKT824LC3
MSDKT824LC3Y
MSE1224
MSE1224Y
MSE1624
MSE1624Y
MSE2024
MSE2024Y
MSE2424
MSE2424Y
MSE2824
MSE2824Y
MSE3224
MSE3224Y
MSE3624
MSE3624Y
MSE4024
MSE4024Y
MSE424
MSE424Y
MSE4424
MSE4424Y
MSE4824
MSE4824Y
MSE824
MSE824Y
MSHDA-TE-24
MSHDA-TE-32
MSHDA-TE-40
MSHDA-TE-48
MSHDA-TE-56
MSHDA-TE-6
MSHDA-TE-64
MSHDA-TE-72
MSHDA-TE-80
MSHDA-TE-88
MSHDS24
MSHDS32
MSHDS40
MSHDS48
MSHDS56
MSHDS64
MSHDS72
MSK2D1224C1
MSK2D1224C1Y
MSK2D1224C2
MSK2D1224C2Y
MSK2D1224C3
MSK2D1224C3Y
MSK2D1624C1
MSK2D1624C1Y
MSK2D1624C2
MSK2D1624C2Y
MSK2D1624C3
MSK2D1624C3Y
MSK2D2024C1
MSK2D2024C1Y
MSK2D2024C2
MSK2D2024C2Y
MSK2D2024C3
MSK2D2024C3Y
MSK2D2424C1
MSK2D2424C1Y
MSK2D2424C2
MSK2D2424C2Y
MSK2D2424C3
MSK2D2424C3Y
MSK2D2824C1
MSK2D2824C1Y
MSK2D2824C2
MSK2D2824C2Y
MSK2D2824C3
MSK2D2824C3Y
MSK2D3224C1
MSK2D3224C1Y
MSK2D3224C2
MSK2D3224C2Y
MSK2D3224C3
MSK2D3224C3Y
MSK2D3624C1
MSK2D3624C1Y
MSK2D3624C2
MSK2D3624C2Y
MSK2D3624C3
MSK2D3624C3Y
MSK2D4024C1
MSK2D4024C1Y
MSK2D4024C2
Part #
45201
46045
45213
46057
45225
46069
47701
47737
47713
47749
47725
47761
37448
47654
37450
47656
37452
47658
37454
47660
37456
47662
37458
47664
37460
47666
37462
47668
37444
47650
37464
47670
37466
47672
37446
47652
72456
72457
72458
72459
72460
72465
72461
72462
72463
72466
70507
70508
70509
70510
70511
70512
70513
45974
45902
45986
45914
45998
45926
45975
45903
45987
45915
45999
45927
45976
45904
45988
45916
46000
45928
45977
45905
45989
45917
46001
45929
45978
45906
45990
45918
46002
45930
45979
45907
45991
45919
46003
45931
45980
45908
45992
45920
46004
45932
45981
45909
45993
Pg Ref.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
“call” indicates call 1-888-373-6767
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
INDEX
Model
MSK2D4024C2Y
MSK2D4024C3
MSK2D4024C3Y
MSK2D424C1
MSK2D424C1Y
MSK2D424C2
MSK2D424C2Y
MSK2D424C3
MSK2D424C3Y
MSK2D4424C1
MSK2D4424C1Y
MSK2D4424C2
MSK2D4424C2Y
MSK2D4424C3
MSK2D4424C3Y
MSK2D4824C1
MSK2D4824C1Y
MSK2D4824C2
MSK2D4824C2Y
MSK2D4824C3
MSK2D4824C3Y
MSK2D8243C1Y
MSK2D824C1
MSK2D824C1Y
MSK2D824C2
MSK2D824C2Y
MSK2D824C3
MSK2D824C3Y
MSK2T1224C1
MSK2T1224C1Y
MSK2T1224C2
MSK2T1224C2Y
MSK2T1224C3
MSK2T1224C3Y
MSK2T1624C1
MSK2T1624C1Y
MSK2T1624C2
MSK2T1624C2Y
MSK2T1624C3
MSK2T1624C3Y
MSK2T2024C1
MSK2T2024C1Y
MSK2T2024C2
MSK2T2024C2Y
MSK2T2024C3
MSK2T2024C3Y
MSK2T2424C1
MSK2T2424C1Y
MSK2T2424C2
MSK2T2424C2Y
MSK2T2424C3
MSK2T2424C3Y
MSK2T2824C1
MSK2T2824C1Y
MSK2T2824C2
MSK2T2824C2Y
MSK2T2824C3
MSK2T2824C3Y
MSK2T3224C1
MSK2T3224C1Y
MSK2T3224C2
MSK2T3224C2Y
MSK2T3224C3
MSK2T3224C3Y
MSK2T3624C1
MSK2T3624C1Y
MSK2T3624C2
MSK2T3624C2Y
MSK2T3624C3
MSK2T3624C3Y
MSK2T4024C1
MSK2T4024C1Y
MSK2T4024C2
MSK2T4024C2Y
MSK2T4024C3
MSK2T4024C3Y
MSK2T424C1
MSK2T424C1Y
MSK2T424C2
MSK2T424C2Y
MSK2T424C3
MSK2T424C3Y
MSK2T4424C1
MSK2T4424C1Y
MSK2T4424C2
MSK2T4424C2Y
MSK2T4424C3
MSK2T4424C3Y
MSK2T4824C1
MSK2T4824C1Y
MSK2T4824C2
MSK2T4824C2Y
MSK2T4824C3
MSK2T4824C3Y
MSK2T824C1
MSK2T824C1Y
MSK2T824C2
MSK2T824C2Y
Part #
45921
46005
45933
45972
45900
45984
45912
45996
45924
45982
45910
45994
45922
46006
45934
45983
45911
45995
45923
46007
45935
78573
45973
45901
45985
45913
45997
45925
46010
45938
46022
45950
46034
45962
46011
45939
46023
45951
46035
45963
46012
45940
46024
45952
46036
45964
46013
45941
46025
45953
46037
45965
46014
45942
46026
45954
46038
45966
46015
45943
46027
45955
46039
45967
46016
45944
46028
45956
46040
45968
46017
45945
46029
45957
46041
45969
46008
45936
46020
45948
46032
45960
46018
45946
46030
45958
46042
45970
46019
45947
46031
45959
46043
45971
46009
45937
46021
45949
Pg Ref.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
“w.o” indicates web only; visit
Model
MSK2T824C3
MSK2T824C3Y
MSKA1224C1
MSKA1224C1Y
MSKA1224C2
MSKA1224C2Y
MSKA1224C3
MSKA1224C3Y
MSKA1624C1
MSKA1624C1Y
MSKA1624C2
MSKA1624C2Y
MSKA1624C3
MSKA1624C3Y
MSKA2024C1
MSKA2024C1Y
MSKA2024C2
MSKA2024C2Y
MSKA2024C3
MSKA2024C3Y
MSKA2424C1
MSKA2424C1Y
MSKA2424C2
MSKA2424C2Y
MSKA2424C3
MSKA2424C3Y
MSKA2824C1
MSKA2824C1Y
MSKA2824C2
MSKA2824C2Y
MSKA2824C3
MSKA2824C3Y
MSKA3224C1
MSKA3224C1Y
MSKA3224C2
MSKA3224C2Y
MSKA3224C3
MSKA3224C3Y
MSKA3624C1
MSKA3624C1Y
MSKA3624C2
MSKA3624C2Y
MSKA3624C3
MSKA3624C3Y
MSKA4024C1
MSKA4024C1Y
MSKA4024C2
MSKA4024C2Y
MSKA4024C3
MSKA4024C3Y
MSKA424C1
MSKA424C1Y
MSKA424C2
MSKA424C2Y
MSKA424C3
MSKA424C3Y
MSKA4424C1
MSKA4424C1Y
MSKA4424C2
MSKA4424C2Y
MSKA4424C3
MSKA4424C3Y
MSKA4824C1
MSKA4824C1Y
MSKA4824C2
MSKA4824C2Y
MSKA4824C3
MSKA4824C3Y
MSKA824C1
MSKA824C1Y
MSKA824C2
MSKA824C2Y
MSKA824C3
MSKA824C3Y
MSKB1224C1
MSKB1224C1Y
MSKB1224C2
MSKB1224C2Y
MSKB1224C3
MSKB1224C3Y
MSKB1624C1
MSKB1624C1Y
MSKB1624C2
MSKB1624C2Y
MSKB1624C3
MSKB1624C3Y
MSKB2024C1
MSKB2024C1Y
MSKB2024C2
MSKB2024C2Y
MSKB2024C3
MSKB2024C3Y
MSKB2424C1
MSKB2424C1Y
MSKB2424C2
MSKB2424C2Y
MSKB2424C3
MSKB2424C3Y
Part #
46033
45961
41102
45603
41114
45615
41126
45627
41103
45604
41115
45616
41127
45628
41104
45605
41116
45617
41128
45629
41105
45606
41117
45618
41129
45630
41106
45607
41118
45619
41130
45631
41107
45608
41119
45620
41131
45632
41108
45609
41120
45621
41132
45633
41109
45610
41121
45622
41133
45634
41100
45601
41112
45613
41124
45625
41110
45611
41122
45623
41134
45635
41111
45612
41123
45624
41135
45636
41101
45602
41113
45614
41125
45626
41138
45639
41150
45651
41162
45663
41139
45640
41151
45652
41163
45664
41140
45641
41152
45653
41164
45665
41141
45642
41153
45654
41165
45666
bannerengineering.com
Pg Ref.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
Model
MSKB2824C1
MSKB2824C1Y
MSKB2824C2
MSKB2824C2Y
MSKB2824C3
MSKB2824C3Y
MSKB3224C1
MSKB3224C1Y
MSKB3224C2
MSKB3224C2Y
MSKB3224C3
MSKB3224C3Y
MSKB3624C1
MSKB3624C1Y
MSKB3624C2
MSKB3624C2Y
MSKB3624C3
MSKB3624C3Y
MSKB4024C1
MSKB4024C1Y
MSKB4024C2
MSKB4024C2Y
MSKB4024C3
MSKB4024C3Y
MSKB424C1
MSKB424C1Y
MSKB424C2
MSKB424C2Y
MSKB424C3
MSKB424C3Y
MSKB4424C1
MSKB4424C1Y
MSKB4424C2
MSKB4424C2Y
MSKB4424C3
MSKB4424C3Y
MSKB4824C1
MSKB4824C1Y
MSKB4824C2
MSKB4824C2Y
MSKB4824C3
MSKB4824C3Y
MSKB824C1
MSKB824C1Y
MSKB824C2
MSKB824C2Y
MSKB824C3
MSKB824C3Y
MSKT1224C1
MSKT1224C1Y
MSKT1224C2
MSKT1224C2Y
MSKT1224C3
MSKT1224C3Y
MSKT1624C1
MSKT1624C1Y
MSKT1624C2
MSKT1624C2Y
MSKT1624C3
MSKT1624C3Y
MSKT2024C1
MSKT2024C1Y
MSKT2024C2
MSKT2024C2Y
MSKT2024C3
MSKT2024C3Y
MSKT2424C1
MSKT2424C1Y
MSKT2424C2
MSKT2424C2Y
MSKT2424C3
MSKT2424C3Y
MSKT2824C1
MSKT2824C1Y
MSKT2824C2
MSKT2824C2Y
MSKT2824C3
MSKT2824C3Y
MSKT3224C1
MSKT3224C1Y
MSKT3224C2
MSKT3224C2Y
MSKT3224C3
MSKT3224C3Y
MSKT3624C1
MSKT3624C1Y
MSKT3624C2
MSKT3624C2Y
MSKT3624C3
MSKT3624C3Y
MSKT4024C1
MSKT4024C1Y
MSKT4024C2
MSKT4024C2Y
MSKT4024C3
MSKT4024C3Y
MSKT424C1
MSKT424C1Y
Part #
41142
45643
41154
45655
41166
45667
41143
45644
41155
45656
41167
45668
41144
45645
41156
45657
41168
45669
41145
45646
41157
45658
41169
45670
41136
45637
41148
45649
41160
45661
41146
45647
41158
45659
41170
45671
41147
45648
41159
45660
41171
45672
41137
45638
41149
45650
41161
45662
43302
45802
43314
45814
43326
45826
43303
45803
43315
45815
43327
45827
43304
45804
43316
45816
43328
45828
43305
45805
43317
45817
43329
45829
43306
45806
43318
45818
43330
45830
43307
45807
43319
45819
43331
45831
43308
45808
43320
45820
43332
45832
43309
45809
43321
45821
43333
45833
43300
45800
“call” indicates call 1-888-373-6767
Pg Ref.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
279
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
INDEX
Model
MSKT424C2
MSKT424C2Y
MSKT424C3
MSKT424C3Y
MSKT4424C1
MSKT4424C1Y
MSKT4424C2
MSKT4424C2Y
MSKT4424C3
MSKT4424C3Y
MSKT4824C1
MSKT4824C1Y
MSKT4824C2
MSKT4824C2Y
MSKT4824C3
MSKT4824C3Y
MSKT824C1
MSKT824C1Y
MSKT824C2
MSKT824C2Y
MSKT824C3
MSKT824C3Y
MSM12A
MSM16A
MSM20A
MSM24A
MSM28A
MSM32A
MSM36A
MSM40A
MSM44A
MSM48A
MSM4A
MSM8A
MSMA-PSC-2
MSMB-1
MSMB-2
MSMB-3
MSMB-4
MSMB-5
MSMB-MSM-45
MSMMB
MSR1224
MSR1224Y
MSR1624
MSR1624Y
MSR2024
MSR2024Y
MSR2424
MSR2424Y
MSR2824
MSR2824Y
MSR3224
MSR3224Y
MSR3624
MSR3624Y
MSR4024
MSR4024Y
MSR424
MSR424Y
MSR4424
MSR4424Y
MSR4824
MSR4824Y
MSR824
MSR824Y
MSS12
MSS16
MSS20
MSS24
MSS28
MSS32
MSS36
MSS4
MSS40
MSS44
MSS48
MSS8
MSVM-1
MSVM-2
MSVM-4
MSXLDKT1224C1
MSXLDKT1224C1Y
MSXLDKT1224C2
MSXLDKT1224C2Y
MSXLDKT1224C3Y
MSXLDKT1224LC1Y
MSXLDKT1224LC2Y
MSXLDKT1224LC3
MSXLDKT1224LC3Y
MSXLDKT1624C1Y
MSXLDKT1624C2
MSXLDKT1624C2Y
MSXLDKT1624C3
MSXLDKT1624C3Y
MSXLDKT1624LC1Y
MSXLDKT1624LC2Y
MSXLDKT1624LC3Y
280
Part #
43312
45812
43324
45824
43310
45810
43322
45822
43334
45834
43311
45811
43323
45823
43335
45835
43301
45801
43313
45813
43325
45825
43164
43165
43166
43167
43168
43169
43170
43171
43172
43173
43162
43163
62867
44696
46116
46166
48954
59671
57117
43151
37449
47655
37451
47657
37453
47659
37455
47661
37457
47663
37459
47665
37461
47667
37463
47669
37445
47651
37465
47671
37467
47673
37447
47653
44310
44311
44312
44313
44314
44315
44316
44308
44317
44318
44319
44309
48955
46149
48956
52687
48187
52699
48199
48211
48502
48514
52891
48526
48188
52700
48200
52712
48212
48503
48515
48527
Pg Ref.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
194
194
194
194
194
194
194
194
194
194
194
194
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
171
171
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
“w.o” indicates web only; visit
Model
MSXLDKT2024C1
MSXLDKT2024C1Y
MSXLDKT2024C2
MSXLDKT2024C2Y
MSXLDKT2024C3Y
MSXLDKT2024LC1
MSXLDKT2024LC1Y
MSXLDKT2024LC2Y
MSXLDKT2024LC3Y
MSXLDKT2424C1Y
MSXLDKT2424C2
MSXLDKT2424C2Y
MSXLDKT2424C3Y
MSXLDKT2424LC1
MSXLDKT2424LC1Y
MSXLDKT2424LC2
MSXLDKT2424LC2Y
MSXLDKT2424LC3Y
MSXLDKT2824C1Y
MSXLDKT2824C2
MSXLDKT2824C2Y
MSXLDKT2824C3
MSXLDKT2824C3Y
MSXLDKT2824LC1Y
MSXLDKT2824LC2Y
MSXLDKT2824LC3
MSXLDKT2824LC3Y
MSXLDKT3224C1
MSXLDKT3224C1Y
MSXLDKT3224C2
MSXLDKT3224C2Y
MSXLDKT3224C3Y
MSXLDKT3224LC1Y
MSXLDKT3224LC2Y
MSXLDKT3224LC3Y
MSXLDKT3624C1Y
MSXLDKT3624C2
MSXLDKT3624C2Y
MSXLDKT3624C3Y
MSXLDKT3624LC1
MSXLDKT3624LC1Y
MSXLDKT3624LC2
MSXLDKT3624LC2Y
MSXLDKT3624LC3
MSXLDKT3624LC3Y
MSXLDKT4024C1Y
MSXLDKT4024C2
MSXLDKT4024C2Y
MSXLDKT4024C3Y
MSXLDKT4024LC1Y
MSXLDKT4024LC2Y
MSXLDKT4024LC3Y
MSXLDKT424C1Y
MSXLDKT424C2
MSXLDKT424C2Y
MSXLDKT424C3Y
MSXLDKT424LC1
MSXLDKT424LC1Y
MSXLDKT424LC2
MSXLDKT424LC2Y
MSXLDKT424LC3Y
MSXLDKT4424C1Y
MSXLDKT4424C2
MSXLDKT4424C2Y
MSXLDKT4424C3Y
MSXLDKT4424LC1Y
MSXLDKT4424LC2Y
MSXLDKT4424LC3Y
MSXLDKT4824C1Y
MSXLDKT4824C2
MSXLDKT4824C2Y
MSXLDKT4824C3Y
MSXLDKT4824LC1Y
MSXLDKT4824LC2
MSXLDKT4824LC2Y
MSXLDKT4824LC3Y
MSXLDKT824C1Y
MSXLDKT824C2
MSXLDKT824C2Y
MSXLDKT824C3Y
MSXLDKT824LC1
MSXLDKT824LC1Y
MSXLDKT824LC2
MSXLDKT824LC2Y
MSXLDKT824LC3Y
MSXLE1224
MSXLE1224Y
MSXLE1624
MSXLE1624Y
MSXLE2024
MSXLE2024Y
MSXLE2424
MSXLE2424Y
MSXLE2824
MSXLE2824Y
MSXLE3224
MSXLE3224Y
MSXLE3624
Part #
52689
48189
52701
48201
48213
52869
48504
48516
48528
48190
52702
48202
48214
52870
48505
52882
48517
48529
48191
52703
48203
52715
48215
48506
48518
52895
48530
52692
48192
52704
48204
48216
48507
48519
48531
48193
52705
48205
48217
52873
48508
52885
48520
52897
48532
48194
52706
48206
48218
48509
48521
48533
48185
52697
48197
48209
52865
48500
52877
48512
48524
48195
52707
48207
48219
48510
48522
48534
48196
52708
48208
48220
48511
52888
48523
48535
48186
52698
48198
48210
52866
48501
52878
48513
48525
52629
48129
52631
48131
52633
48133
52635
48135
52637
48137
52639
48139
52641
bannerengineering.com
Pg Ref.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
Model
MSXLE3624Y
MSXLE4024
MSXLE4024Y
MSXLE424
MSXLE424Y
MSXLE4424
MSXLE4424Y
MSXLE4824
MSXLE4824Y
MSXLE824
MSXLE824Y
MSXLHDE2412Y
MSXLHDE3212Y
MSXLHDE4012Y
MSXLHDE4812Y
MSXLHDE5612Y
MSXLHDE6412Y
MSXLHDE7212Y
MSXLHDR2412Y
MSXLHDR3212Y
MSXLHDR4012Y
MSXLHDR4812Y
MSXLHDR5612Y
MSXLHDR6412Y
MSXLHDR7212Y
MSXLK2D1224C1Y
MSXLK2D1224C2Y
MSXLK2D1224C3
MSXLK2D1224C3Y
MSXLK2D1624C1
MSXLK2D1624C1Y
MSXLK2D1624C2
MSXLK2D1624C2Y
MSXLK2D1624C3Y
MSXLK2D2024C1
MSXLK2D2024C1Y
MSXLK2D2024C2Y
MSXLK2D2024C3Y
MSXLK2D2424C1Y
MSXLK2D2424C2Y
MSXLK2D2424C3Y
MSXLK2D2824C1
MSXLK2D2824C1Y
MSXLK2D2824C2Y
MSXLK2D2824C3
MSXLK2D2824C3Y
MSXLK2D3224C1Y
MSXLK2D3224C2Y
MSXLK2D3224C3Y
MSXLK2D3624C1Y
MSXLK2D3624C2
MSXLK2D3624C2Y
MSXLK2D3624C3Y
MSXLK2D4024C1Y
MSXLK2D4024C2Y
MSXLK2D4024C3Y
MSXLK2D424C1Y
MSXLK2D424C2
MSXLK2D424C2Y
MSXLK2D424C3Y
MSXLK2D4424C1Y
MSXLK2D4424C2Y
MSXLK2D4424C3Y
MSXLK2D4824C1Y
MSXLK2D4824C2Y
MSXLK2D4824C3Y
MSXLK2D824C1Y
MSXLK2D824C2Y
MSXLK2D824C3
MSXLK2D824C3Y
MSXLK2T2024C1Y
MSXLK2T3224C1Y
MSXLK2T3624C1Y
MSXLK2T3624C2Y
MSXLK2T3624C3Y
MSXLK2T424C2
MSXLK2T4824C2
MSXLK2T4824C2Y
MSXLKA1224C1
MSXLKA1224C1Y
MSXLKA1224C2
MSXLKA1224C2Y
MSXLKA1224C3
MSXLKA1224C3Y
MSXLKA1624C1
MSXLKA1624C1Y
MSXLKA1624C2
MSXLKA1624C2Y
MSXLKA1624C3
MSXLKA1624C3Y
MSXLKA2024C1
MSXLKA2024C1Y
MSXLKA2024C2
MSXLKA2024C2Y
MSXLKA2024C3
MSXLKA2024C3Y
MSXLKA2424C1
MSXLKA2424C1Y
Part #
48141
52643
48143
52625
48125
52645
48145
52647
48147
52627
48127
68963
68965
68967
68969
68971
68973
68975
68964
68966
68968
68970
68972
68974
68976
49925
49937
52819
49949
52796
49926
52808
49938
49950
52797
49927
49939
49951
49928
49940
49952
52799
49929
49941
52823
49953
49930
49942
49954
49931
52813
49943
49955
49932
49944
49956
49923
52805
49935
49947
49933
49945
49957
49934
49946
49958
49924
49936
52818
49948
49963
49966
49967
49979
49991
52841
52852
49982
52651
48151
52663
48163
52675
48175
52652
48152
52664
48164
52676
48176
52653
48153
52665
48165
52677
48177
52654
48154
Pg Ref.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
“call” indicates call 1-888-373-6767
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
INDEX
Model
MSXLKA2424C2
MSXLKA2424C2Y
MSXLKA2424C3
MSXLKA2424C3Y
MSXLKA2824C1
MSXLKA2824C1Y
MSXLKA2824C2
MSXLKA2824C2Y
MSXLKA2824C3
MSXLKA2824C3Y
MSXLKA3224C1
MSXLKA3224C1Y
MSXLKA3224C2
MSXLKA3224C2Y
MSXLKA3224C3
MSXLKA3224C3Y
MSXLKA3624C1
MSXLKA3624C1Y
MSXLKA3624C2
MSXLKA3624C2Y
MSXLKA3624C3
MSXLKA3624C3Y
MSXLKA4024C1
MSXLKA4024C1Y
MSXLKA4024C2
MSXLKA4024C2Y
MSXLKA4024C3
MSXLKA4024C3Y
MSXLKA424C1
MSXLKA424C1Y
MSXLKA424C2
MSXLKA424C2Y
MSXLKA424C3
MSXLKA424C3Y
MSXLKA4424C1
MSXLKA4424C1Y
MSXLKA4424C2
MSXLKA4424C2Y
MSXLKA4424C3
MSXLKA4424C3Y
MSXLKA4824C1
MSXLKA4824C1Y
MSXLKA4824C2
MSXLKA4824C2Y
MSXLKA4824C3
MSXLKA4824C3Y
MSXLKA824C1
MSXLKA824C1Y
MSXLKA824C2
MSXLKA824C2Y
MSXLKA824C3
MSXLKA824C3Y
MSXLKB1224C1Y
MSXLKB1224C2Y
MSXLKB2024C1
MSXLKB2024C1Y
MSXLKB2024C2Y
MSXLKB2424C1
MSXLKB2424C2Y
MSXLKB2824C1Y
MSXLKB3224C2Y
MSXLKB3224C3
MSXLKB3624C2
MSXLKT1224C1Y
MSXLKT1224C2
MSXLKT1624C1Y
MSXLKT1624C3Y
MSXLKT2024C2Y
MSXLKT2424C2
MSXLKT2424C2Y
MSXLKT2424C3
MSXLKT2424C3Y
MSXLKT2824C2
MSXLKT2824C2Y
MSXLKT3224C1Y
MSXLKT3224C2Y
MSXLKT3624C2Y
MSXLKT4024C1Y
MSXLKT4024C2
MSXLKT4024C3Y
MSXLKT424C2Y
MSXLKT4824C2
MSXLKT4824C3Y
MSXLR1224
MSXLR1224Y
MSXLR1624
MSXLR1624Y
MSXLR2024
MSXLR2024Y
MSXLR2424
MSXLR2424Y
MSXLR2824
MSXLR2824Y
MSXLR3224
MSXLR3224Y
MSXLR3624
MSXLR3624Y
MSXLR4024
Part #
52666
48166
52678
48178
52655
48155
52667
48167
52679
48179
52656
48156
52668
48168
52680
48180
52657
48157
52669
48169
52681
48181
52658
48158
52670
48170
52682
48182
52649
48149
52661
48161
52673
48173
52659
48159
52671
48171
52683
48183
52660
48160
52672
48172
52684
48184
52650
48150
52662
48162
52674
48174
49853
49865
52725
49855
49867
52726
49868
49857
49870
52752
52741
49889
52771
49890
49914
49903
52774
49904
52786
49916
52775
49905
49894
49906
49907
49896
52778
49920
49899
52780
49922
52630
48130
52632
48132
52634
48134
52636
48136
52638
48138
52640
48140
52642
48142
52644
Pg Ref.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
“w.o” indicates web only; visit
Model
MSXLR4024Y
MSXLR424
MSXLR424Y
MSXLR4424
MSXLR4424Y
MSXLR4824
MSXLR4824Y
MSXLR824
MSXLR824Y
MS-XPE-32
MS-XPE-43
MUSAB-1
MUSA-MH-1
MUSA-PS-1
MUSA-TA-1
MUSC-1
MUSC-1T3
MUSF-RM-1
OTBA5
OTBA5 W/G
OTBA5 W/R
OTBA5 W/Y
OTBA5L
OTBA5L W/G
OTBA5L W/R
OTBA5L W/Y
OTBA5LQD
OTBA5LQD W/G
OTBA5LQD W/R
OTBA5LQD W/Y
OTBA5QD
OTBA5QD W/G
OTBA5QD W/R
OTBA5QD W/Y
OTBB5
OTBB5 W/G
OTBB5 W/R
OTBB5 W/Y
OTBB5L
OTBB5L W/G
OTBB5L W/R
OTBB5L W/Y
OTBB5LQD
OTBB5LQD W/G
OTBB5LQD W/R
OTBB5LQD W/Y
OTBB5QD
OTBB5QD W/G
OTBB5QD W/R
OTBB5QD W/Y
OTBVN6
OTBVN6 W/G
OTBVN6 W/R
OTBVN6 W/Y
OTBVN6L
OTBVN6L W/G
OTBVN6L W/R
OTBVN6L W/Y
OTBVN6LQD
OTBVN6LQD W/G
OTBVN6LQD W/R
OTBVN6LQD W/Y
OTBVN6LQDH
OTBVN6QD
OTBVN6QD W/G
OTBVN6QD W/R
OTBVN6QD W/Y
OTBVP6
OTBVP6 W/G
OTBVP6 W/R
OTBVP6 W/Y
OTBVP6L
OTBVP6L W/G
OTBVP6L W/R
OTBVP6L W/Y
OTBVP6LQD
OTBVP6LQD W/G
OTBVP6LQD W/R
OTBVP6LQD W/Y
OTBVP6LQDH
OTBVP6QD
OTBVP6QD W/G
OTBVP6QD W/R
OTBVP6QD W/Y
OTBVR81
OTBVR81 W/G
OTBVR81 W/R
OTBVR81 W/Y
OTBVR81L
OTBVR81L W/G
OTBVR81L W/R
OTBVR81L W/Y
OTBVR81LQD
OTBVR81LQD W/G
OTBVR81LQD W/R
OTBVR81LQD W/Y
OTBVR81QD
OTBVR81QD W/G
Part #
48144
52626
48126
52646
48146
52648
48148
52628
48128
63440
64218
43833
43831
43832
43834
41200
64127
80942
27986
35098
35058
35078
32167
35100
35060
35080
32255
35101
35061
35081
28149
35099
35059
35079
27987
35102
35062
35082
32254
35104
35064
35084
32256
35105
35065
35085
28150
35103
35063
35083
28591
35110
35070
35090
33706
35112
35072
35092
35057
35113
35073
35093
67222
28585
35111
35071
35091
28589
35114
35074
35094
34110
35116
35076
35096
34997
35117
35077
35097
67223
28590
35115
35075
35095
33080
35106
35066
35086
34040
35108
35068
35088
34041
35109
35069
35089
34078
35107
bannerengineering.com
Pg Ref.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
Model
OTBVR81QD W/R
OTBVR81QD W/Y
OTC-1-BK
OTC-1-GN
OTC-1-RD
OTC-1-YW
PFC-2-25
PGAB-1
PGAB-2
PGA-PSA-1
PGA-PSB-1
PGA-TBA1-1
PGA-TBA2-1
PGCA-1A
PGCA-2A
PGCB-1A
PGCB-2A
PGCB-2A
PIU4100U
PIU4100UXP
PIU4100UXT
PIU41600U
PIU41600UXP
PIU41600UXT
PIU4200U
PIU4200UXP
PIU4200UXT
PIU430U
PIU430UXP
PIU430UXT
PIU4330U
PIU4330UXP
PIU4330UXT
PIU4500U
PIU4500UXP
PIU4500UXT
PIU460U
PIU460UXP
PIU460UXT
PSDINA-24
PWS4100P
PWS410P
PWS4110P
PWS4120P
PWS4130P
PWS4140P
PWS4150P
PWS415P
PWS4200P
PWS420P
PWS4250P
PWS425P
PWS4300P
PWS430P
PWS435P
PWS43P
PWS440P
PWS445P
PWS450P
PWS45P
PWS460P
PWS470P
PWS47P
PWS480P
PWS490P
PWXP4100P
PWXP410P
PWXP4110P
PWXP4120P
PWXP4130P
PWXP4140P
PWXP4150P
PWXP415P
PWXP4200P
PWXP420P
PWXP4250P
PWXP425P
PWXP4300P
PWXP430P
PWXP435P
PWXP43P
PWXP440P
PWXP445P
PWXP450P
PWXP45P
PWXP460P
PWXP470P
PWXP47P
PWXP480P
PWXP490P
PWXT4100P
PWXT410P
PWXT4110P
PWXT4120P
PWXT4130P
PWXT4140P
PWXT4150P
PWXT415P
Part #
35067
35087
30221
30979
30977
30978
02613
30699
30698
30697
30696
34069
34070
34052
34053
34054
34055
34055
26937
71565
71570
31003
71569
71574
39996
71566
71571
26751
70720
68618
36623
71567
71572
26941
71568
71573
26230
70721
68619
54989
70417
70411
02827
02828
02829
02830
02831
02816
02832
02817
02833
02818
70420
02819
02820
02813
02821
02822
70414
02814
02823
02824
02815
02825
02826
70418
70412
02848
02849
02850
02851
02852
02837
02853
02838
02854
02839
70421
02840
02841
02834
02842
02843
70415
02835
02844
02845
02836
02846
02847
70419
70413
02869
02870
02871
02872
02873
02858
“call” indicates call 1-888-373-6767
Pg Ref.
w.o.
w.o.
119
119
119
119
69
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
w.o.
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
281
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
INDEX
Model
PWXT4200P
PWXT420P
PWXT4250P
PWXT425P
PWXT4300P
PWXT430P
PWXT435P
PWXT43P
PWXT440P
PWXT445P
PWXT450P
PWXT45P
PWXT460P
PWXT470P
PWXT47P
PWXT480P
PWXT490P
QDC-5100
QDC-5125
QDC-5150
QDC-515C
QDC-525
QDC-525C
QDC-550
QDC-550C
QDE2R4-815D
QDE2R4-825D
QDE-5100D
QDE-515D
QDE-525D
QDE-550D
QDE-575D
QDE-8100D
QDE-815D
QDE-825D
QDE-830D
QDE-850D
QDE-875D
QDS-3100C
QDS-315C
QDS-325C
QDS-350C
QDS-375C
QDS-515C
QDS-525C
QDS-550C
QDS-715C
QDS-725C
QDS-750C
QDS-815C
QDS-825C
QDS-850C
QDS-875C
QDU-515C
QDU-525C
QDU-550C
RDLP-8100D
RDLP-8100DB
RDLP-815D
RDLP-815DB
RDLP-825D
RDLP-825DB
RDLP-850D
RDLP-850DB
RDLP-875D
RDLP-875DB
RPA-C1-10
RPA-C1-100
RPA-C1-20
RPA-C2-10
RPA-C2-20
RPA-C2-50
RPA-C2-80
RPA-C3-100
RPA-C3-20
RPA-CC1-4
RPA-CC2-4
RPA-CC3-4
RPA-DP1-1
RPA-EB1-1
RPA-EB2-1
RPA-P1-1
RPA-S1-1
RPA-S2-1
RPA-S3-1
RPA-S4-1
RPA-S5-1
RPA-S6-1
RPA-T1-4
RPA-T2-4
RPA-T3-4
RPA-TA1-1
RPA-TA2-1
RP-LM40D-6
RP-LM40D-6L
RP-LS42F-75L
RP-LS42F-75LE
RP-LS42F-75LF
Part #
02874
02859
02875
02860
70422
02861
02862
02855
02863
02864
70416
02856
02865
02866
02857
02867
02868
35339
35340
35341
37442
35336
37443
35337
37498
73257
73258
71465
70880
70881
70882
71464
71467
70883
70884
78943
70885
71466
68428
68425
68426
68427
71162
68430
68431
68432
67209
67210
67211
67212
67213
67214
71126
46391
46392
46393
80796
82785
80792
82781
80793
82782
80794
82783
80795
82784
62074
69779
62075
62076
62077
46694
46695
62079
62078
62068
62069
62070
83388
62080
65039
62081
62073
62089
46693
46994
83386
83387
62065
62066
62067
62071
62072
62057
62058
67707
67708
47899
Pg Ref.
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
181
181
179
179
179
179
179
179
179
179
w.o.
179
179
183
183
183
183
183
184
184
184
188
188
188
184
184
184
184
w.o.
w.o.
w.o.
181
181
181
181
181
181
181
181
181
181
161
161
161
161
161
161
161
161
161
161
161
161
161
161
161
161
161
161
161
161
161
161
161
161
161
161
161
160
160
158
158
158
282
“w.o” indicates web only; visit
Model
RP-QM72D-12L
RP-QM72D-6L
RP-QM90F-100L
RP-QMT72D-20L
RP-QMT72E-12L
RP-QMT72F-12L
RP-RM83F-38LR
RP-RM83F-38LRE
RP-RM83F-38LT
RP-RM83F-38LTE
RP-RM83F-75LR
RP-RM83F-75LRE
RP-RM83F-75LT
RP-RM83F-75LTE
SC22-3-C
SC22-3-CU1
SC22-3E-C
SC22-3E-CU1
SC22-3E-S
SC22-3E-SU1
SC22-3-S
SC22-3-SU1
SC-IM9A
SC-IM9B
SC-IM9C
SC-SC22-3
SC-SC22-3E
SC-TC1
SC-TS1
SC-USB1
SC-XM1
SC-XMP
SFA-CMH
SFA-CTB1
SFA-CTB2
SFA-CTB3
SFA-CTB4
SFA-FA
SFA-FCC-008
SFA-FCC-015
SFA-FCC-025
SFA-FCC-050
SFA-FCC-100
SFA-FCC-CGM20
SFA-FFP
SFA-FGD1HD
SFA-FS
SFA-IAG
SFA-IMB1
SFA-IMB2
SFA-LAT-12
SFA-LAT-30
SFA-RD
SFA-W-1
SFCDT-4A1
SFCDT-4A1C
SFCDT-4A1CM
SFG2-500C100
SFG2-500C15
SFG2-500C25
SFG2-500C50
SFG2-500C8
SFG2-584C100
SFG2-584C15
SFG2-584C25
SFG2-584C50
SFG2-584C8
SFG3-400C100
SFG3-400C15
SFG3-400C25
SFG3-400C50
SFG3-400C8
SFG3-533C100
SFG3-533C15
SFG3-533C25
SFG3-533C50
SFG3-533C8
SFG4-300C100
SFG4-300C15
SFG4-300C25
SFG4-300C50
SFG4-300C8
SFI-A1
SFI-A1ED
SFI-A1HD
SFI-A1XP
SFI-A1XT
SFI-D1
SFI-D1EDPXT15
SFI-D1EDPXT30
SFI-D1EDPXT50
SFI-D1EDPXT6
SFI-D1HDPS15
SFI-D1HDPS30
SFI-D1HDPS50
SFI-D1HDPS6
SFI-D1HDPXT15
SFI-D1HDPXT30
Part #
62060
62059
62064
62061
62062
62063
82129
82127
82128
82126
81877
81875
81876
81874
77913
77915
83368
83370
83367
83369
77259
77914
77814
77815
77823
79715
83371
77813
77812
77724
76177
77708
69769
02638
02639
02640
75264
70382
74323
74324
74325
74326
74327
74328
76711
74803
69777
02618
02641
02642
73000
73001
69013
75178
70403
71846
74329
74688
70811
70812
70813
74687
74690
70814
70815
70816
74689
74692
70817
70818
70819
74691
74694
70820
70821
70822
74693
74696
70823
70824
70825
74695
69775
73266
73818
02986
02985
69774
73263
73264
73265
73262
74885
74886
74887
74884
74781
74782
bannerengineering.com
Pg Ref.
159
159
160
159
159
159
158
158
158
158
158
158
158
158
77
77
77
77
77
77
77
77
77
77
77
78
78
78
78
78
78
78
70
70
70
70
70
69
69
69
69
69
69
69
w.o.
65
69
70
171
172
197
197
67
70
60
60
60
62
62
62
62
62
62
62
62
62
62
62
62
62
62
62
62
62
62
62
62
62
62
62
62
62
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
Model
SFI-D1HDPXT50
SFI-D1HDPXT6
SFI-M12SS06UXT
SFI-M12SS15UXT
SFI-M12SS30UXT
SFI-R1L
SFI-R1R
SFI-S1L
SFI-S1R
SFP12PS15
SFP12PS25
SFP12PS50
SFP12PS8
SFP12PXP15
SFP12PXP25
SFP12PXP50
SFP12PXP8
SFP12PXT15
SFP12PXT25
SFP12PXT30
SFP12PXT50
SFP12PXT8
SFP30SS100
SFP30SS15
SFP30SS25
SFP30SS50
SFP30SS8
SFP30SXP100
SFP30SXP15
SFP30SXP25
SFP30SXP50
SFP30SXP8
SFP30SXT100
SFP30SXT15
SFP30SXT25
SFP30SXT50
SFP30SXT8
SFS-EBM-01E1
SFS-EBM-01E2
SGE2-500
SGE2-500Q3
SGE2-500Q5
SGE2-500Q8E
SGE2-584
SGE2-584Q3
SGE2-584Q8E
SGE3-400
SGE3-400Q3
SGE3-400Q5
SGE3-400Q8E
SGE3-533
SGE3-533Q3
SGE3-533Q5
SGE3-533Q8E
SGE4-300
SGE4-300Q3
SGE4-300Q5
SGE4-300Q8E
SGK2-500-Q83-1RE25
SGK2-584Q88E-1RE25
SGK3-400Q88E-1RE15
SGK3-533Q83-1RE25
SGK3-533Q85-1RE15
SGK3-533Q88E-1RE15
SGK3-533Q88E-1RE25
SGK4-300Q88E-1RE15
SGP2-500
SGP2-500Q83
SGP2-500Q85
SGP2-500Q88E
SGP2-584
SGP2-584Q83
SGP2-584Q88E
SGP3-400
SGP3-400Q83
SGP3-400Q85
SGP3-400Q88E
SGP3-533
SGP3-533Q83
SGP3-533Q85
SGP3-533Q88E
SGP4-300
SGP4-300Q83
SGP4-300Q88E
SGR2-500
SGR2-500Q8
SGR2-500Q8E
SGR2-584
SGR2-584Q8
SGR2-584Q8E
SGR3-400
SGR3-400Q8
SGR3-400Q8E
SGR3-533
SGR3-533Q8
SGR3-533Q8E
SGR4-300
SGR4-300Q8
Part #
74783
74780
72285
72059
72282
69773
69772
69771
69770
69732
69734
69736
73015
72523
72524
72525
73016
72526
72527
72302
72528
73017
73021
72529
72530
72531
73018
73022
69738
69739
69740
73019
73023
69741
69742
69743
73020
76648
76649
61867
72543
75507
75683
61870
69733
75752
61873
46777
46922
76656
61876
71397
02653
75816
61879
70600
41378
75831
77473
78565
79767
77869
78021
76982
78453
78351
61869
74561
75508
75680
61872
75118
75751
61875
74871
75509
76655
61878
73182
74355
75814
61881
74114
75813
61868
72569
75684
61871
02745
75753
61874
46920
76657
61877
02654
75815
61880
70602
Pg Ref.
65
65
65
65
65
65
65
65
65
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
66
66
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
46
46
46
46
46
46
46
46
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
“call” indicates call 1-888-373-6767
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
INDEX
Model
SGR4-300Q8E
SGXLE2-500
SGXLE2-500Q3
SGXLE2-500Q5
SGXLE2-500Q8E
SGXLE2-584
SGXLE2-584Q3
SGXLE2-584Q5
SGXLE2-584Q8E
SGXLE3-400
SGXLE3-400Q3
SGXLE3-400Q5
SGXLE3-400Q8E
SGXLE3-533
SGXLE3-533Q3
SGXLE3-533Q5
SGXLE3-533Q8E
SGXLE4-300
SGXLE4-300Q3
SGXLE4-300Q5
SGXLE4-300Q8E
SGXLK3-400Q83-1RE25
SGXLK4-300Q83-1RE25
SGXLK4-300Q88-1RE50
SGXLP2-500
SGXLP2-500Q83
SGXLP2-500Q88E
SGXLP2-584
SGXLP2-584Q83
SGXLP3-400
SGXLP3-400Q83
SGXLP3-400Q88E
SGXLP3-533
SGXLP3-533Q83
SGXLP3-533Q88E
SGXLP4-300
SGXLP4-300Q83
SGXLP4-300Q88E
SI-HG63A
SI-HG63FQDL
SI-HG63FQDR
SI-HG63FQDRR
SI-HG63-TK1
SI-HG80A
SI-HG80DQD
SI-HG80DQDR
SI-LM40KHD
SI-LM40KHE
SI-LM40KHF
SI-LM40KVD
SI-LM40KVE
SI-LM40MKHD
SI-LM40MKHE
SI-LM40MKHF
SI-LM40MKHFD
SI-LM40MKHFE
SI-LM40MKHFF
SI-LM40MKVD
SI-LM40MKVE
SI-LS100F
SI-LS100MRFF
SI-LS100SF
SI-LS100SRAF
SI-LS31HGD
SI-LS31HGE
SI-LS31HGLD
SI-LS31HGLE
SI-LS31HGRD
SI-LS31HGRE
SI-LS31RTD
SI-LS31RTE
SI-LS42-COVER
SI-LS42DMG
SI-LS42DMH
SI-LS42DMI
SI-LS42DMJ
SI-LS42DMMG
SI-LS42DMMGF
SI-LS42DMMH
SI-LS42DMMHF
SI-LS42DMMI
SI-LS42DMMIF
SI-LS42DMMJ
SI-LS42DMMJF
SI-LS42DMSG
SI-LS42DMSGF
SI-LS42DMSH
SI-LS42DMSHF
SI-LS42DMSI
SI-LS42DMSIF
SI-LS42DMSJ
SI-LS42DMSJF
SI-LS42DSG
SI-LS42DSH
SI-LS42DSI
SI-LS42DSJ
SI-LS42UMG
SI-LS42UMH
Part #
75786
62749
74284
75142
79544
62751
71095
75125
76439
62753
02939
75141
77849
62755
71095
75125
76439
62757
02746
74069
75785
79192
80695
04508
62750
76060
79543
62752
75441
62754
79188
77848
62756
78468
76438
62758
75655
75784
76924
76922
76921
78451
77428
46733
46731
46732
49474
49475
49476
49478
49479
46724
56978
67691
55754
56979
67692
46725
62810
49480
58744
58740
58741
46718
56982
46720
56984
46719
56983
46721
56985
46995
47873
47877
47881
47884
60082
60086
60090
60094
61412
61416
62779
47900
60080
60084
60088
60092
61410
61414
62778
71273
47871
47875
47879
47883
47874
47878
Pg Ref.
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
46
46
46
45
45
45
45
45
45
45
45
45
45
45
45
45
45
130
130
130
130
w.o.
131
131
131
142
142
142
142
142
142
142
142
142
142
142
142
142
136
136
136
136
132
132
132
132
132
132
133
133
149
146
146
146
146
146
146
146
146
146
146
146
146
145
145
145
145
145
145
145
145
145
145
145
145
146
146
“w.o” indicates web only; visit
Model
SI-LS42UMI
SI-LS42UMMG
SI-LS42UMMGF
SI-LS42UMMH
SI-LS42UMMHF
SI-LS42UMMI
SI-LS42UMMIF
SI-LS42UMSG
SI-LS42UMSGF
SI-LS42UMSH
SI-LS42UMSHF
SI-LS42UMSI
SI-LS42UMSIF
SI-LS42USG
SI-LS42USH
SI-LS42USI
SI-LS83D
SI-LS83E
SI-LS83MRFD
SI-LS83MRFE
SI-LS83SD
SI-LS83SE
SI-LS83SRAD
SI-LS83SRAE
SI-MAG1C
SI-MAG1MM
SI-MAG1MM90
SI-MAG1MMHF
SI-MAG1SM
SI-MAG1SMCO
SI-MAG2MM
SI-MAG2SM
SI-MAG3MM
SI-MAG3SM
SI-PL2A-R
SI-PL3A-G
SI-PL3A-R
SI-PL3T-G
SI-PL3T-R
SI-QM100AMG
SI-QM100AMMG
SI-QM100AMSG
SI-QM100ASG
SI-QM100DMG
SI-QM100DMMG
SI-QM100DMSG
SI-QM100DMSH
SI-QM100DSG
SI-QM100DSH
SI-QM-13
SI-QM-13-M20
SI-QM-90A
SI-QM-CGM20
SI-QM-M20
SI-QM-SB
SI-QM-SMFA
SI-QM-SSA
SI-QM-SSAXL
SI-QS-100
SI-QS75C
SI-QS75MC
SI-QS75MC-100
SI-QS75MFC
SI-QS75MRHC
SI-QS75MRVC
SI-QS90D
SI-QS90E
SI-QS90F
SI-QS90MD
SI-QS90MD-100
SI-QS90ME
SI-QS90ME-100
SI-QS90MF
SI-QS90MF-100
SI-QS90MFD
SI-QS90MFE
SI-QS90MFF
SI-QS-CG13
SI-QS-CGM16
SI-QS-CGM20
SI-QS-FSA
SI-QS-M16
SI-QS-M20
SI-QS-SSA
SI-QS-SSA-2
SI-QS-SSA-3
SI-QS-SSA-4
SI-QS-SSU
SLPCE14-1110
SLPCE14-1110P8
SLPCE14-1250
SLPCE14-1250P8
SLPCE14-1390
SLPCE14-1390P8
SLPCE14-1530
SLPCE14-1530P8
SLPCE14-1670
SLPCE14-1670P8
Part #
47882
60083
60087
60091
60095
61413
61417
60081
60085
60089
60093
61411
61415
47872
47876
47880
49481
49482
58749
58754
58745
58750
58746
58751
46728
46990
56992
56991
46989
56993
46992
46991
56987
56986
60169
66802
66803
66804
66805
49464
46716
46713
49461
49463
46715
46712
77733
49460
77751
48559
66579
48556
65148
65147
47895
48562
48555
67693
48561
49472
46700
82169
56975
46701
46702
49466
49468
49470
46703
82170
46706
82171
46709
82172
56972
56973
56974
48564
65144
65146
48554
62088
65145
48551
58855
58856
47896
46996
83685
83593
83686
83594
83687
83595
83688
83596
83689
83597
bannerengineering.com
Pg Ref.
146
146
146
146
146
146
146
145
145
145
145
145
145
145
145
145
136
136
136
136
136
136
136
136
w.o.
127
127
127
127
127
127
127
127
127
w.o.
193
193
193
193
147
147
147
147
147
147
147
147
147
147
187
187
149
187
187
149
149
149
w.o.
149
137
137
137
137
w.o.
w.o.
138
138
138
138
138
138
138
138
138
138
138
138
187
187
187
w.o.
187
187
187
149
149
149
149
33
33
34
34
34
34
34
34
34
34
Model
SLPCE14-1810
SLPCE14-1810P8
SLPCE14-410
SLPCE14-410P8
SLPCE14-550
SLPCE14-550P8
SLPCE14-690
SLPCE14-690P8
SLPCE14-830
SLPCE14-830P8
SLPCE14-970
SLPCE14-970P8
SLPCE25-1110
SLPCE25-1110P8
SLPCE25-1250
SLPCE25-1250P8
SLPCE25-1390
SLPCE25-1390P8
SLPCE25-1530
SLPCE25-1530P8
SLPCE25-1670
SLPCE25-1670P8
SLPCE25-1810
SLPCE25-1810P8
SLPCE25-410
SLPCE25-410P8
SLPCE25-550
SLPCE25-550P8
SLPCE25-690
SLPCE25-690P8
SLPCE25-830
SLPCE25-830P8
SLPCE25-970
SLPCE25-970P8
SLPCP14-1110
SLPCP14-1110P88
SLPCP14-1250
SLPCP14-1250P88
SLPCP14-1390
SLPCP14-1390P88
SLPCP14-1530
SLPCP14-1530P88
SLPCP14-1670
SLPCP14-1670P88
SLPCP14-1810
SLPCP14-1810P88
SLPCP14-410
SLPCP14-410P88
SLPCP14-550
SLPCP14-550P88
SLPCP14-690
SLPCP14-690P88
SLPCP14-830
SLPCP14-830P88
SLPCP14-970
SLPCP14-970P88
SLPCP25-1110
SLPCP25-1110P88
SLPCP25-1250
SLPCP25-1250P88
SLPCP25-1390
SLPCP25-1390P88
SLPCP25-1530
SLPCP25-1530P88
SLPCP25-1670
SLPCP25-1670P88
SLPCP25-1810
SLPCP25-1810P88
SLPCP25-410
SLPCP25-410P88
SLPCP25-550
SLPCP25-550P88
SLPCP25-690
SLPCP25-690P88
SLPCP25-830
SLPCP25-830P88
SLPCP25-970
SLPCP25-970P88
SLPCR14-1110
SLPCR14-1110P8
SLPCR14-1250
SLPCR14-1250P8
SLPCR14-1390
SLPCR14-1390P8
SLPCR14-1530
SLPCR14-1530P8
SLPCR14-1670
SLPCR14-1670P8
SLPCR14-1810
SLPCR14-1810P8
SLPCR14-410
SLPCR14-410P8
SLPCR14-550
SLPCR14-550P8
SLPCR14-690
SLPCR14-690P8
SLPCR14-830
SLPCR14-830P8
Part #
83690
83598
83680
83588
83681
83589
83682
83590
83683
83591
83684
83592
83707
83615
83708
83616
83709
83617
83710
83618
83711
83619
83712
83620
83702
83610
83703
83611
83704
83612
83705
83613
83706
83614
83799
83753
83800
83754
83801
83755
83802
83756
83803
83757
83804
83758
83794
83748
83795
83749
83796
83750
83797
83751
83798
83752
83810
83764
83811
83765
83812
83766
83813
83767
83814
83768
83815
83769
83805
83759
83806
83760
83807
83761
83808
83762
83809
83763
83696
83604
83697
83605
83698
83606
83699
83607
83700
83608
83701
83609
83691
83599
83692
83600
83693
83601
83694
83602
“call” indicates call 1-888-373-6767
Pg Ref.
34
34
33
33
33
33
33
33
33
33
33
33
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
33
33
34
34
34
34
34
34
34
34
34
34
33
33
33
33
33
33
33
33
33
33
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
33
34
34
34
34
34
34
34
34
34
34
34
33
33
33
33
33
33
33
33
283
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
INDEX
Model
SLPCR14-970
SLPCR14-970P8
SLPCR25-1110
SLPCR25-1110P8
SLPCR25-1250
SLPCR25-1250P8
SLPCR25-1390
SLPCR25-1390P8
SLPCR25-1530
SLPCR25-1530P8
SLPCR25-1670
SLPCR25-1670P8
SLPCR25-1810
SLPCR25-1810P8
SLPCR25-410
SLPCR25-410P8
SLPCR25-550
SLPCR25-550P8
SLPCR25-690
SLPCR25-690P8
SLPCR25-830
SLPCR25-830P8
SLPCR25-970
SLPCR25-970P8
SLPE14-1110
SLPE14-1110P8
SLPE14-1250
SLPE14-1250P8
SLPE14-1390
SLPE14-1390P8
SLPE14-1530
SLPE14-1530P8
SLPE14-1670
SLPE14-1670P8
SLPE14-1810
SLPE14-1810P8
SLPE14-270
SLPE14-270P8
SLPE14-410
SLPE14-410P8
SLPE14-550
SLPE14-550P8
SLPE14-690
SLPE14-690P8
SLPE14-830
SLPE14-830P8
SLPE14-970
SLPE14-970P8
SLPE25-1110
SLPE25-1110P8
SLPE25-1250
SLPE25-1250P8
SLPE25-1390
SLPE25-1390P8
SLPE25-1530
SLPE25-1530P8
SLPE25-1670
SLPE25-1670P8
SLPE25-1810
SLPE25-1810P8
SLPE25-270
SLPE25-270P8
SLPE25-410
SLPE25-410P8
SLPE25-550
SLPE25-550P8
SLPE25-690
SLPE25-690P8
SLPE25-830
SLPE25-830P8
SLPE25-970
SLPE25-970P8
SLPP14-1110
SLPP14-1110P88
SLPP14-1250
SLPP14-1250P88
SLPP14-1390
SLPP14-1390P88
SLPP14-1530
SLPP14-1530P88
SLPP14-1670
SLPP14-1670P88
SLPP14-1810
SLPP14-1810P88
SLPP14-270
SLPP14-270P88
SLPP14-410
SLPP14-410P88
SLPP14-550
SLPP14-550P88
SLPP14-690
SLPP14-690P88
SLPP14-830
SLPP14-830P88
SLPP14-970
SLPP14-970P88
SLPP25-1110
SLPP25-1110P88
284
Part #
83695
83603
83718
83626
83719
83627
83720
83628
83721
83629
83722
83630
83723
83631
83713
83621
83714
83622
83715
83623
83716
83624
83717
83625
83638
83546
83639
83547
83640
83548
83641
83549
83642
83550
83643
83551
83632
83540
83633
83541
83634
83542
83635
83543
83636
83544
83637
83545
83662
83570
83663
83571
83664
83572
83665
83573
83666
83574
83667
83575
83656
83564
83657
83565
83658
83566
83659
83567
83660
83568
83661
83569
83776
83730
83777
83731
83778
83732
83779
83733
83780
83734
83781
83735
83770
83724
83771
83725
83772
83726
83773
83727
83774
83728
83775
83729
83788
83742
Pg Ref.
33
33
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
33
33
33
33
33
33
33
33
33
33
33
33
32
32
32
32
32
32
32
32
33
33
33
33
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
33
33
“w.o” indicates web only; visit
Model
SLPP25-1250
SLPP25-1250P88
SLPP25-1390
SLPP25-1390P88
SLPP25-1530
SLPP25-1530P88
SLPP25-1670
SLPP25-1670P88
SLPP25-1810
SLPP25-1810P88
SLPP25-270
SLPP25-270P88
SLPP25-410
SLPP25-410P88
SLPP25-550
SLPP25-550P88
SLPP25-690
SLPP25-690P88
SLPP25-830
SLPP25-830P88
SLPP25-970
SLPP25-970P88
SLPR14-1110
SLPR14-1110P8
SLPR14-1250
SLPR14-1250P8
SLPR14-1390
SLPR14-1390P8
SLPR14-1530
SLPR14-1530P8
SLPR14-1670
SLPR14-1670P8
SLPR14-1810
SLPR14-1810P8
SLPR14-270
SLPR14-270P8
SLPR14-410
SLPR14-410P8
SLPR14-550
SLPR14-550P8
SLPR14-690
SLPR14-690P8
SLPR14-830
SLPR14-830P8
SLPR14-970
SLPR14-970P8
SLPR25-1110
SLPR25-1110P8
SLPR25-1250
SLPR25-1250P8
SLPR25-1390
SLPR25-1390P8
SLPR25-1530
SLPR25-1530P8
SLPR25-1670
SLPR25-1670P8
SLPR25-1810
SLPR25-1810P8
SLPR25-270
SLPR25-270P8
SLPR25-410
SLPR25-410P8
SLPR25-550
SLPR25-550P8
SLPR25-690
SLPR25-690P8
SLPR25-830
SLPR25-830P8
SLPR25-970
SLPR25-970P8
SLSCE14-1050P8
SLSCE14-1050Q8
SLSCE14-1200P8
SLSCE14-1200Q8
SLSCE14-1350P8
SLSCE14-1350Q8
SLSCE14-1500P8
SLSCE14-1500Q8
SLSCE14-1650P8
SLSCE14-1650Q8
SLSCE14-1800P8
SLSCE14-1800Q8
SLSCE14-300P8
SLSCE14-300Q8
SLSCE14-450P8
SLSCE14-450Q8
SLSCE14-600P8
SLSCE14-600Q8
SLSCE14-750P8
SLSCE14-750Q8
SLSCE14-900P8
SLSCE14-900Q8
SLSCE30-1050P8
SLSCE30-1050Q8
SLSCE30-1200P8
SLSCE30-1200Q8
SLSCE30-1350P8
SLSCE30-1350Q8
Part #
83789
83743
83790
83744
83791
83745
83792
83746
83793
83747
83782
83736
83783
83737
83784
83738
83785
83739
83786
83740
83787
83741
83650
83558
83651
83559
83652
83560
83653
83561
83654
83562
83655
83563
83644
83552
83645
83553
83646
83554
83647
83555
83648
83556
83649
83557
83674
83582
83675
83583
83676
83584
83677
83585
83678
83586
83679
83587
83668
83576
83669
83577
83670
83578
83671
83579
83672
83580
83673
83581
73909
72404
73910
72405
73911
73375
73912
73376
73913
73377
73914
73378
73904
72399
73905
72400
73906
72401
73907
72402
73908
72403
73920
72411
73921
72412
73922
72413
bannerengineering.com
Pg Ref.
33
33
33
33
33
33
33
33
33
33
32
32
32
32
32
32
32
32
33
33
33
33
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
33
33
33
33
33
33
33
33
33
33
33
33
32
32
32
32
32
32
32
32
33
33
33
33
25
25
25
25
25
25
26
26
26
26
26
26
25
25
25
25
25
25
25
25
25
25
26
26
26
26
26
26
Model
SLSCE30-1500P8
SLSCE30-1500Q8
SLSCE30-1650P8
SLSCE30-1650Q8
SLSCE30-1800P8
SLSCE30-1800Q8
SLSCE30-1950P8
SLSCE30-1950Q8
SLSCE30-2100P8
SLSCE30-2100Q8
SLSCE30-2250P8
SLSCE30-2250Q8
SLSCE30-2400P8
SLSCE30-2400Q8
SLSCE30-300P8
SLSCE30-300Q8
SLSCE30-450P8
SLSCE30-450Q8
SLSCE30-600P8
SLSCE30-600Q8
SLSCE30-750P8
SLSCE30-750Q8
SLSCE30-900P8
SLSCE30-900Q8
SLSCK14-1350Q88-2RE15
SLSCK14-450Q88-1RE15
SLSCK14-900Q88-RE15
SLSCK14-900Q88-RE25
SLSCK30-1050Q88-1RE15
SLSCK30-1050Q88-1RE25
SLSCK30-1200Q88-1RE15
SLSCK30-1500Q88-RE25
SLSCK30-1800Q88-RE25
SLSCK30-300Q88-1RE25
SLSCK30-450Q88-1RE15
SLSCK30-450Q88-1RE25
SLSCK30-600P88-1RE15
SLSCK30-750Q88-1RE15
SLSCK30-900Q88-1RE25
SLSCP14-1050P88
SLSCP14-1050Q88
SLSCP14-1200P88
SLSCP14-1200Q88
SLSCP14-1350P88
SLSCP14-1350Q88
SLSCP14-1500P88
SLSCP14-1500Q88
SLSCP14-1650P88
SLSCP14-1650Q88
SLSCP14-1800P88
SLSCP14-1800Q88
SLSCP14-300P88
SLSCP14-300Q88
SLSCP14-450P88
SLSCP14-450Q88
SLSCP14-600P88
SLSCP14-600Q88
SLSCP14-750P88
SLSCP14-750Q88
SLSCP14-900P88
SLSCP14-900Q88
SLSCP30-1050P88
SLSCP30-1050Q88
SLSCP30-1200P88
SLSCP30-1200Q88
SLSCP30-1350P88
SLSCP30-1350Q88
SLSCP30-1500P88
SLSCP30-1500Q88
SLSCP30-1650P88
SLSCP30-1650Q88
SLSCP30-1800P88
SLSCP30-1800Q88
SLSCP30-1950P88
SLSCP30-1950Q88
SLSCP30-2100P88
SLSCP30-2100Q88
SLSCP30-2250P88
SLSCP30-2250Q88
SLSCP30-2400P88
SLSCP30-2400Q88
SLSCP30-300P88
SLSCP30-300Q88
SLSCP30-450P88
SLSCP30-450Q88
SLSCP30-600P88
SLSCP30-600Q88
SLSCP30-750P88
SLSCP30-750Q88
SLSCP30-900P88
SLSCP30-900Q88
SLSCR14-1050P8
SLSCR14-1050Q8
SLSCR14-1200P8
SLSCR14-1200Q8
SLSCR14-1350P8
SLSCR14-1350Q8
SLSCR14-1500P8
Part #
73923
72414
73924
72415
73925
72416
83818
83819
83820
78996
81821
81822
81823
81824
73915
72406
73916
72407
73917
72408
73918
72409
73919
72410
79787
79891
79417
77998
78135
77370
79050
79319
79320
79310
77367
77369
78042
77929
77119
73977
72441
73978
72442
73979
73383
73980
73384
73981
73385
73982
73386
73972
72436
73973
72437
73974
72438
73975
72439
73976
72440
73988
72449
73989
72450
73990
72451
73991
72452
73992
72453
73993
72454
83825
83826
83827
78994
83828
80762
83829
80763
73983
72444
73984
72445
73985
72446
73986
72447
73987
72448
73931
72422
73932
72423
73933
73379
73934
Pg Ref.
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
25
25
25
25
25
25
26
26
26
26
26
26
25
25
25
25
25
25
25
25
25
25
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
25
25
25
25
25
25
26
“call” indicates call 1-888-373-6767
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
INDEX
Model
SLSCR14-1500Q8
SLSCR14-1650P8
SLSCR14-1650Q8
SLSCR14-1800P8
SLSCR14-1800Q8
SLSCR14-300P8
SLSCR14-300Q8
SLSCR14-450P8
SLSCR14-450Q8
SLSCR14-600P8
SLSCR14-600Q8
SLSCR14-750P8
SLSCR14-750Q8
SLSCR14-900P8
SLSCR14-900Q8
SLSCR30-1050P8
SLSCR30-1050Q8
SLSCR30-1200P8
SLSCR30-1200Q8
SLSCR30-1350P8
SLSCR30-1350Q8
SLSCR30-1500P8
SLSCR30-1500Q8
SLSCR30-1650P8
SLSCR30-1650Q8
SLSCR30-1800P8
SLSCR30-1800Q8
SLSCR30-1950P8
SLSCR30-1950Q8
SLSCR30-2100P8
SLSCR30-2100Q8
SLSCR30-2250P8
SLSCR30-2250Q8
SLSCR30-2400P8
SLSCR30-2400Q8
SLSCR30-300P8
SLSCR30-300Q8
SLSCR30-450P8
SLSCR30-450Q8
SLSCR30-600P8
SLSCR30-600Q8
SLSCR30-750P8
SLSCR30-750Q8
SLSCR30-900P8
SLSCR30-900Q8
SLSE14-1050P8
SLSE14-1050Q5
SLSE14-1050Q8
SLSE14-1200P8
SLSE14-1200Q5
SLSE14-1200Q8
SLSE14-1350P8
SLSE14-1350Q5
SLSE14-1350Q8
SLSE14-1500P8
SLSE14-1500Q5
SLSE14-1500Q8
SLSE14-150P8
SLSE14-150Q5
SLSE14-150Q8
SLSE14-1650P8
SLSE14-1650Q5
SLSE14-1650Q8
SLSE14-1800Q5
SLSE14-1800Q8
SLSE14-300P8
SLSE14-300Q5
SLSE14-300Q8
SLSE14-450P8
SLSE14-450Q5
SLSE14-450Q8
SLSE14-600P8
SLSE14-600Q5
SLSE14-600Q8
SLSE14-750P8
SLSE14-750Q5
SLSE14-750Q8
SLSE14-900P8
SLSE14-900Q5
SLSE14-900Q8
SLSE30-1050P8
SLSE30-1050Q5
SLSE30-1050Q8
SLSE30-1200P8
SLSE30-1200Q5
SLSE30-1200Q8
SLSE30-1350P8
SLSE30-1350Q5
SLSE30-1350Q8
SLSE30-1500P8
SLSE30-1500Q5
SLSE30-1500Q8
SLSE30-150P8
SLSE30-150Q5
SLSE30-150Q8
SLSE30-1650P8
SLSE30-1650Q5
SLSE30-1650Q8
Part #
73380
73935
73381
73936
73382
73926
72417
73927
72418
73928
72419
73929
72420
73930
72421
73942
72429
73943
72430
73944
72431
73945
72432
73946
72433
73947
72434
83830
83831
83832
78997
83833
83834
83835
83836
73937
72424
73938
72425
73939
72426
73940
72427
73941
72428
73862
71218
72365
73863
71219
72366
73864
73355
73359
73865
73356
73360
73856
71212
72359
73866
73357
73361
73358
73362
73857
71213
72360
73858
71214
72361
73859
71215
72362
73860
71216
72363
73861
71217
72364
73874
71242
72373
73875
71243
72374
73876
71244
72375
73877
71245
72376
73868
71236
72367
73878
71246
72377
Pg Ref.
26
26
26
26
26
25
25
25
25
25
25
25
25
25
25
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
25
25
25
25
25
25
25
25
25
25
25
25
24
24
24
25
25
25
“w.o” indicates web only; visit
Model
SLSE30-1800P5
SLSE30-1800P8
SLSE30-1800Q8
SLSE30-1950P8
SLSE30-1950Q5
SLSE30-1950Q8
SLSE30-2100P8
SLSE30-2100Q5
SLSE30-2100Q8
SLSE30-2250P8
SLSE30-2250Q5
SLSE30-2250Q8
SLSE30-2400P8
SLSE30-2400Q5
SLSE30-2400Q8
SLSE30-300P8
SLSE30-300Q5
SLSE30-300Q8
SLSE30-450P8
SLSE30-450Q5
SLSE30-450Q8
SLSE30-600P8
SLSE30-600Q5
SLSE30-600Q8
SLSE30-750P8
SLSE30-750Q5
SLSE30-750Q8
SLSE30-900P8
SLSE30-900Q5
SLSE30-900Q8
SLSK14-1200Q88-2RE25
SLSK14-1200Q88-RE25
SLSK14-1350Q88-2RE15
SLSK14-1350Q88-2RE25
SLSK14-1500Q88-1RE15
SLSK14-150P88-2RE15
SLSK14-1800Q85-2R15E25
SLSK14-300NQ88-2RE15
SLSK14-300Q85-1R15E25
SLSK14-300Q88-2RE15
SLSK14-300Q88-3RE15
SLSK14-300Q88-3RE25
SLSK14-300Q88-RE25
SLSK14-450NQ88-1RE25
SLSK14-450Q88-1RE15
SLSK14-450Q88-2RE25
SLSK14-450Q88-5RE25
SLSK14-600Q85-2R15E25
SLSK14-600Q88-2RE25
SLSK14-600Q88-5RE25
SLSK14-600Q88-6RE25
SLSK14-600Q88-RE15
SLSK14-750Q88-1RE15
SLSK14-750Q88-1RE25
SLSK14-750Q88-RE15
SLSK14-900Q88-2RE15
SLSK14-900Q88-RE25
SLSK30-1050P88-2RE25
SLSK30-1050Q85-1RE25
SLSK30-1050Q88-2RE25
SLSK30-1050Q88-RE15
SLSK30-1200P88-2RE25
SLSK30-1200Q85-RE25
SLSK30-1200Q88-1R25E15
SLSK30-1200Q88-2R25E15
SLSK30-1200Q88-2RE25
SLSK30-1350Q85-RE25
SLSK30-1350Q88-1RE15
SLSK30-1350Q88-2RE25
SLSK30-1350Q88-5RE15
SLSK30-1350Q88-RE25
SLSK30-1500Q85-RE25
SLSK30-1500Q88-1RE15
SLSK30-1500Q88-2RE25
SLSK30-150Q88-1RE15
SLSK30-150Q88-1RE25
SLSK30-150Q88-2RE15
SLSK30-1650Q85-2RE25
SLSK30-1650Q85-RE25
SLSK30-1650Q88-1RE15
SLSK30-1650Q88-RE15
SLSK30-1800Q88-1RE15
SLSK30-1800Q88-2RE15
SLSK30-300Q88-1R15E25
SLSK30-300Q88-1RE25
SLSK30-300Q88-6RE15
SLSK30-300Q88-RE15
SLSK30-450NQ88-1RE25
SLSK30-450Q88-1RE25
SLSK30-600AQ88-1RE15
SLSK30-600Q85-RE25
SLSK30-600Q88-1R15E50
SLSK30-600Q88-1R25E15
SLSK30-600Q88-1RE75
SLSK30-600Q88-4R25E15
SLSK30-600Q88-4RE25
SLSK30-750P88-2RE15
SLSK30-750Q88-1RE15
Part #
71247
73879
72378
83837
83838
82067
83839
83840
82068
83841
83842
79018
83843
83844
82069
73869
71237
72368
73870
71238
72369
73871
71239
72370
73872
71240
72371
73873
71241
72372
78475
81507
78046
78019
78853
78339
81440
78122
78452
78458
79884
79885
81531
77409
73477
78412
79185
81431
79510
79654
78850
78089
73478
77329
78737
78869
77399
77582
81258
77677
78837
78575
72252
79427
81097
78438
72253
81229
77332
78571
77911
72254
78550
78439
77304
75691
79157
81526
72255
78556
81280
78031
78127
78699
77282
79754
77707
77691
80665
79377
72250
79899
78987
78528
77371
77225
79007
73505
bannerengineering.com
Pg Ref.
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
Model
SLSK30-750Q88-1RE50
SLSK30-750Q88-RE15
SLSK30-900P88-2RE15
SLSK30-900Q85-RE25
SLSK30-900Q88-1RE15
SLSK30-900Q88-5RE15
SLSK30-900Q88-RE15
SLSP14-1050P88
SLSP14-1050Q85
SLSP14-1050Q88
SLSP14-1200P88
SLSP14-1200Q85
SLSP14-1200Q88
SLSP14-1350P88
SLSP14-1350Q85
SLSP14-1350Q88
SLSP14-1500P88
SLSP14-1500Q85
SLSP14-1500Q88
SLSP14-150P88
SLSP14-150Q85
SLSP14-150Q88
SLSP14-1650P88
SLSP14-1650Q85
SLSP14-1650Q88
SLSP14-1800P88
SLSP14-1800Q85
SLSP14-1800Q88
SLSP14-300P88
SLSP14-300Q85
SLSP14-300Q88
SLSP14-450P88
SLSP14-450Q85
SLSP14-450Q88
SLSP14-600P88
SLSP14-600Q85
SLSP14-600Q88
SLSP14-750P88
SLSP14-750Q85
SLSP14-750Q88
SLSP14-900P88
SLSP14-900Q85
SLSP14-900Q88
SLSP30-1050P88
SLSP30-1050Q85
SLSP30-1050Q88
SLSP30-1200P88
SLSP30-1200Q85
SLSP30-1200Q88
SLSP30-1350P88
SLSP30-1350Q85
SLSP30-1350Q88
SLSP30-1500P88
SLSP30-1500Q85
SLSP30-1500Q88
SLSP30-150P88
SLSP30-150Q85
SLSP30-150Q88
SLSP30-1650P88
SLSP30-1650Q85
SLSP30-1650Q88
SLSP30-1800P88
SLSP30-1800Q85
SLSP30-1800Q88
SLSP30-1950P88
SLSP30-1950Q85
SLSP30-1950Q88
SLSP30-2100P88
SLSP30-2100Q85
SLSP30-2100Q88
SLSP30-2250P88
SLSP30-2250Q85
SLSP30-2250Q88
SLSP30-2400P88
SLSP30-2400Q85
SLSP30-2400Q88
SLSP30-300P88
SLSP30-300Q85
SLSP30-300Q88
SLSP30-450P88
SLSP30-450Q85
SLSP30-450Q88
SLSP30-600P88
SLSP30-600Q85
SLSP30-600Q88
SLSP30-750P88
SLSP30-750Q85
SLSP30-750Q88
SLSP30-900P88
SLSP30-900Q85
SLSP30-900Q88
SLSR14-1050P8
SLSR14-1050Q8
SLSR14-1200P8
SLSR14-1200Q8
SLSR14-1350P8
SLSR14-1350Q8
SLSR14-1500P8
Part #
77333
78922
78539
72251
78549
79658
81147
73954
71234
72385
73955
71235
72386
73956
73367
73371
73957
73368
73372
73948
71228
72379
73958
73369
73373
73959
73370
73374
73949
71229
72380
73950
71230
72381
73951
71231
72382
73952
71232
72383
73953
71233
72384
73966
71266
72393
73967
71267
72394
73968
71268
72395
73969
71269
72396
73960
71260
72387
73970
71270
72397
73971
71271
72398
83845
83846
82074
83847
83848
82075
83849
83850
82076
83851
83852
82077
73961
71261
72388
73962
71262
72389
73963
71263
72390
73964
71264
72391
73965
71265
72392
73886
71226
73887
71227
73888
73363
73889
“call” indicates call 1-888-373-6767
Pg Ref.
27
27
27
27
27
27
27
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
25
25
25
25
25
25
25
25
25
25
25
25
24
24
24
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
285
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
INDEX
Model
SLSR14-1500Q8
SLSR14-150P8
SLSR14-150Q8
SLSR14-1650P8
SLSR14-1650Q8
SLSR14-1800P8
SLSR14-1800Q8
SLSR14-300P8
SLSR14-300Q8
SLSR14-450P8
SLSR14-450Q8
SLSR14-600P8
SLSR14-600Q8
SLSR14-750P8
SLSR14-750Q8
SLSR14-900P8
SLSR14-900Q8
SLSR30-1050P8
SLSR30-1050Q8
SLSR30-1200P8
SLSR30-1200Q8
SLSR30-1350P8
SLSR30-1350Q8
SLSR30-1500P8
SLSR30-1500Q8
SLSR30-150P8
SLSR30-150Q8
SLSR30-1650P8
SLSR30-1650Q8
SLSR30-1800P8
SLSR30-1800Q8
SLSR30-1950P8
SLSR30-1950Q8
SLSR30-2100P8
SLSR30-2100Q8
SLSR30-2250P8
SLSR30-2250Q8
SLSR30-2400P8
SLSR30-2400Q8
SLSR30-300P8
SLSR30-300Q8
SLSR30-450P8
SLSR30-450Q8
SLSR30-600P8
SLSR30-600Q8
SLSR30-750P8
SLSR30-750Q8
SLSR30-900P8
SLSR30-900Q8
SMA-MBK-1
SMB12MM
SMB1812SF
SMB30A
SMB30MM
SMB30SC
SMBAMS30P
SMBAMS30RA
SMBAMSBRA
SMBR55F01
SMBR55F02
SMBR55FRA
SM-GA-5A
SM-HA-5A
SPE1
SPE1Q3
SPE1Q5
SPE1Q8E
SPK1Q83-2RE15
SPK1Q88E-1RE25
SPKA-AG12-1
SPKA-AG30-1
SPP1
SPP1Q83
SPP1Q88E
SPR1
SPR1Q8
SPR1Q8E
SPXLE1
SPXLE1Q3
SPXLE1Q5
SPXLE1Q8E
SPXLP1
SPXLP1Q85
SPXLP1Q88E
SSA-EBM-02E
SSA-EBM-02L
SSA-EBM-11E
SSA-EBM-11L
SSA-EBM-12E
SSA-EBM-12L
SSA-EBP-02E
SSA-EBP-02L
SSA-EBP-11E
SSA-EBP-11L
SSA-EBP-12E
SSA-EBP-12L
SSA-ML-A
SSA-ML-W
286
Part #
73364
73880
71220
73890
73365
73891
73366
73881
71221
73882
71222
73883
71223
73884
71224
73885
71225
73898
71254
73899
71255
73900
71256
73901
71257
73892
71248
73902
71258
73903
71259
83853
82070
83854
82071
83855
82072
83856
82073
73893
71249
73894
71250
73895
71251
73896
71252
73897
71253
61933
27635
52520
32723
27162
52521
73135
73137
73138
67104
02903
58809
66093
66094
61864
70147
71983
75812
78353
77372
73179
73180
61866
74925
76208
61865
70148
75811
62747
71094
74371
77326
62748
74367
77325
69705
69699
69706
69700
69707
69701
69708
69702
69709
69703
69710
69704
70494
62095
Pg Ref.
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
25
25
25
25
25
25
25
25
24
24
25
25
25
25
25
25
25
25
25
25
25
25
24
24
24
24
24
24
24
24
24
24
172
172
172
173
173
173
173
174
174
174
174
175
92
92
45
45
45
45
47
47
198
198
45
45
45
45
45
45
45
45
45
45
45
45
45
155
154
155
154
155
154
155
155
155
155
155
155
193
193
“w.o” indicates web only; visit
Model
SSM-100
SSM-100-S
SSM-1100
SSM-1100-S
SSM-1175
SSM-1175-S
SSM-1275
SSM-1275-S
SSM-1400
SSM-1400-S
SSM-1475
SSM-1475-S
SSM-150
SSM-150-S
SSM-1550
SSM-1550-S
SSM-1675
SSM-1675-S
SSM-1750
SSM-1750-S
SSM-1900
SSM-1900-S
SSM-200
SSM-200-S
SSM-250
SSM-250-S
SSM-375
SSM-375-S
SSM-475
SSM-475-S
SSM-550
SSM-550-S
SSM-675
SSM-675-S
SSM-825
SSM-825-S
SSM-875
SSM-875-S
SSM-975
SSM-975-S
SSM-FM-11A10
SSM-FM-11A20
SS-XPE-32
SS-XPE-43
STBA-RB1-MB1
STBA-RB1-MB2
STBA-RB1-MB3
STBA-RB1-S1
STBA-RB1-S2
STBA-RB2-MB2
STBA-RB2-MB3
STBA-RB2-S1
STBA-RB2-S2
STBVP6
STBVP6L
STBVP6LQ
STBVP6LQ5
STBVP6Q
STBVP6Q5
STBVP6-RB1
STBVP6-RB1E02
STBVP6-RB1Q8
STBVP6-RB2
STBVP6-RB2E02
STBVP6-RB2Q8
STBVR81
STBVR81L
STBVR81LQ
STBVR81LQ6
STBVR81Q
STBVR81Q6
STBVR81-RB1
STP07
STP-1
STP-10
STP-11
STP-12
STP-13
STP-14
STP-15
STP-16
STP-17
STP-18
STP-2
STP25
STP-3
STP-4
STP-5
STP50
STP-6
STP-7
STP75
STP-8
STP-9
STPX07
STPX25
STPX50
STPX75
Part #
61890
63470
71616
71623
61899
63479
61900
63480
71617
71624
61901
63481
61891
63471
71618
71625
61902
63482
71620
71626
61903
63483
71450
71451
61892
63472
61893
63473
61894
63474
61895
63475
61896
63476
61897
63477
71615
71622
61898
63478
10179
10180
71932
71933
77858
77859
77860
77861
77862
83345
83346
83347
83348
64179
64182
64183
64184
64180
64181
77805
77806
78265
83343
83344
83538
64190
64193
64194
64195
64191
64192
80685
69985
43835
62026
66046
46914
71929
71930
71931
82850
82851
82852
43957
69986
43958
43836
43837
77974
43838
48981
77976
49126
50694
69987
69988
77971
75320
bannerengineering.com
Pg Ref.
195
196
195
196
195
196
195
196
195
196
195
196
195
196
195
196
195
196
195
196
195
196
195
196
195
196
195
196
195
196
195
196
195
196
195
196
195
196
195
196
104
104
203
203
175
175
175
199
199
122
122
199
199
118
w.o.
w.o.
w.o.
118
118
121
121
121
121
121
121
118
w.o.
w.o.
w.o.
118
118
w.o.
185
w.o.
w.o.
w.o.
w.o.
28
28
28
36
36
36
w.o.
185
28
w.o.
w.o.
185
w.o.
w.o.
185
w.o.
w.o.
185
185
185
185
Model
T18RGX8PQ8
T30GRYB11P
T30RGX8PQ8
TL50GRYQ
TL50YQ
TL50WQ
UM-FA-11A
UM-FA-9A
USAB-1
USAB-2
USA-LAT-2
USA-MH-2
USA-PMS-40
USA-PMS-62
USA-PTB-1
USA-PTB-2
USA-PTB-3
USA-PTB-4
USA-PTB-5
USCC-1L2M
USCC-1T2M
USCC-1T3M
USCC-2L2M
USCC-2L3M
USCC-2T2M
USCC-2T3M
USCD-1L2
USCD-1T2
USCD-1T3
USCD-2L2
USCD-2T2
USCD-2T3
USCD-2T3E
USCMB-1
USCMB-2
USCT-2T2
USCT-2T3
USDAB-1
USDAB-1D
USDAB-1E
USDAB-2
USDAB-2D
USDAL-1
USDAL-1D
USDAL-2
USDAL-2D
USDA-RM-1
USDA-RM-2
USDINT-1L2
USDINT-1L2D
USDINT-1L4
USDINT-1L4D
USDINT-1T2
USDINT-1T2D
USDINT-1T2E
USDINT-1T4
USDINT-1T4D
USDINT-2L2
USDINT-2L2D
USDINT-2L4
USDINT-2L4D
USDINT-2T2
USDINT-2T2D
USDINT-2T4
USDINT-2T4D
USDK2T1224C4YP2
USDK2T1224C5Y
USDK2T1224C5YP2
USDK2T1224YI
USDK2T1624C4YP2
USDK2T1624C5Y
USDK2T1624C5YP2
USDK2T1624YI
USDK2T2024C4YP2
USDK2T2024C5Y
USDK2T2024C5YP2
USDK2T2024YI
USDK2T2412C5Y
USDK2T24244C4YP2
USDK2T2424C4YP2
USDK2T2424C5Y
USDK2T2424C5YP2
USDK2T2424YI
USDK2T2824C4YP2
USDK2T2824C5Y
USDK2T2824C5YP2
USDK2T2824LC5YP2
USDK2T2824YI
USDK2T3212C4YP2
USDK2T3212C5Y
USDK2T3212C5YP2
USDK2T3212YI
USDK2T3224C4YP2
USDK2T3224C5Y
USDK2T3224C5YP2
USDK2T3224YI
USDK2T3624C4YP2
USDK2T3624C5Y
Part #
75976
78149
75114
81861
10067
10173
81228
81227
51885
51886
54303
60110
57115
57114
55676
55677
55678
55679
55680
60108
67231
66550
66869
67686
71702
72579
67169
51225
67247
67171
51224
65998
62812
51651
54976
63491
68396
50002
52245
62092
50003
52246
55624
55625
55626
55627
50001
55707
54176
54177
55597
55598
48536
48772
52440
55589
55590
54178
54179
55599
55600
49785
49786
55591
55592
49663
57021
49675
42538
49664
57022
49676
42539
49665
57023
49677
42540
57031
46796
49666
57024
49678
42541
49667
57025
49679
79086
42542
54505
57032
54509
54473
49668
57026
49680
42543
49669
57027
Pg Ref.
192
192
192
193
193
193
90
90
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
176
176
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
“call” indicates call 1-888-373-6767
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
INDEX
Model
USDK2T3624C5YP2
USDK2T3624YI
USDK2T4012C5Y
USDK2T4012YI
USDK2T4024C4YP2
USDK2T4024C5Y
USDK2T4024C5YP2
USDK2T4024YI
USDK2T424C4YP2
USDK2T424C5Y
USDK2T424C5YP2
USDK2T424YI
USDK2T4424C4YP2
USDK2T4424C5Y
USDK2T4424C5YP2
USDK2T4424YI
USDK2T4812C4YP2
USDK2T4812C5Y
USDK2T4812C5YP2
USDK2T4812YI
USDK2T4824C4YP2
USDK2T4824C5Y
USDK2T4824C5YP2
USDK2T4824YI
USDK2T5612C4YP2
USDK2T5612C5Y
USDK2T5612C5YP2
USDK2T5612YI
USDK2T6412C4YP2
USDK2T6412C5Y
USDK2T6412C5YP2
USDK2T6412YI
USDK2T7212C4YP2
USDK2T7212C5Y
USDK2T7212C5YP2
USDK2T7212C8YP2
USDK2T7212YI
USDK2T824C4YP2
USDK2T824C5Y
USDK2T824C5YP2
USDK2T824YI
USDK2TD1224C4YP2
USDK2TD1224C5Y
USDK2TD1224C5YP2
USDK2TD1224YI
USDK2TD1624C4YP2
USDK2TD1624C5Y
USDK2TD1624C5YP2
USDK2TD1624YI
USDK2TD2024C4YP2
USDK2TD2024C5Y
USDK2TD2024C5YP2
USDK2TD2024YI
USDK2TD2412C5Y
USDK2TD2424C4YP2
USDK2TD2424C5Y
USDK2TD2424C5YP2
USDK2TD2424YI
USDK2TD2824C4YP2
USDK2TD2824C5Y
USDK2TD2824C5YP2
USDK2TD2824YI
USDK2TD3212C5Y
USDK2TD3224C4YP2
USDK2TD3224C5Y
USDK2TD3224C5YP2
USDK2TD3224YI
USDK2TD3624C4YP2
USDK2TD3624C5Y
USDK2TD3624C5YP2
USDK2TD3624YI
USDK2TD4012C5Y
USDK2TD4024C4YP2
USDK2TD4024C5Y
USDK2TD4024C5YP2
USDK2TD4024YI
USDK2TD424C4YP2
USDK2TD424C5Y
USDK2TD424C5YP2
USDK2TD424YI
USDK2TD4424C4YP2
USDK2TD4424C5Y
USDK2TD4424C5YP2
USDK2TD4424YI
USDK2TD4812C5Y
USDK2TD4824C4YP2
USDK2TD4824C5Y
USDK2TD4824C5YP2
USDK2TD4824YI
USDK2TD5612C5Y
USDK2TD6412C5Y
USDK2TD6412C5YP2
USDK2TD7212C5Y
USDK2TD824C4YP2
USDK2TD824C5Y
USDK2TD824C5YP2
USDK2TD824YI
USDKT1224C4YP2
Part #
49681
42544
57033
54474
49670
57028
49682
42545
49661
57019
49673
42536
49671
57029
49683
42546
54507
57034
54511
54475
49672
57030
49684
42547
51709
57035
51712
51721
51710
57036
51713
51722
51711
57037
51714
54974
51723
49662
57020
49674
42537
49735
57059
49747
42562
49736
57060
49748
42563
49737
57061
49749
42564
57069
49738
57062
49750
42565
49739
57063
49751
42566
57070
49740
57064
49752
42567
49741
57065
49753
42568
57071
49742
57066
49754
42569
49733
57057
49745
42560
49743
57067
49755
42570
57072
49744
57068
49756
42571
57073
57074
51737
57075
49734
57058
49746
42561
49627
Pg Ref.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
“w.o” indicates web only; visit
Model
USDKT1224C5Y
USDKT1224C5YP2
USDKT1224YI
USDKT1624C4YP2
USDKT1624C5Y
USDKT1624C5YP2
USDKT1624YI
USDKT2024C4YP2
USDKT2024C5Y
USDKT2024C5YP2
USDKT2024YI
USDKT2412C4YP2
USDKT2412C5Y
USDKT2412C5YP2
USDKT2412YI
USDKT2424C4YP2
USDKT2424C5Y
USDKT2424C5YP2
USDKT2424YI
USDKT2824C4YP2
USDKT2824C5Y
USDKT2824C5YP2
USDKT2824YI
USDKT3212C4YP2
USDKT3212C5Y
USDKT3212YI
USDKT32244C5Y
USDKT3224C4YP2
USDKT3224C5Y
USDKT3224C5YP2
USDKT3224YI
USDKT3624C4YP2
USDKT3624C5Y
USDKT3624C5YP2
USDKT3624YI
USDKT4012C4YP2
USDKT4012C5Y
USDKT4012C5YP2
USDKT4024C4YP2
USDKT4024C5Y
USDKT4024C5YP2
USDKT4024YI
USDKT424C4YP2
USDKT424C5Y
USDKT424C5YP2
USDKT424YI
USDKT4424C4YP2
USDKT4424C5Y
USDKT4424C5YP2
USDKT4424YI
USDKT4812C4YP2
USDKT4812C5Y
USDKT4812C5YP2
USDKT4812YI
USDKT4824C4Y
USDKT4824C4YP2
USDKT4824C5Y
USDKT4824C5YP2
USDKT4824YI
USDKT5612C4YP2
USDKT5612C5Y
USDKT5612C5YP2
USDKT5612YI
USDKT6412C4YP2
USDKT6412C5Y
USDKT6412C5YP2
USDKT6412YI
USDKT7212C4YP2
USDKT7212C5Y
USDKT7212C5YP2
USDKT824C4YP2
USDKT824C5Y
USDKT824C5YP2
USDKT824YI
USDKTD1224C4YP2
USDKTD1224C5Y
USDKTD1224C5YP2
USDKTD1224YI
USDKTD1624C4YP2
USDKTD1624C5Y
USDKTD1624C5YP2
USDKTD1624YI
USDKTD2024C4YP2
USDKTD2024C5Y
USDKTD2024C5YP2
USDKTD2024YI
USDKTD2412C5Y
USDKTD2412C5YP2
USDKTD2424C4YP2
USDKTD2424C5Y
USDKTD2424C5YP2
USDKTD2424YI
USDKTD2824C4YP2
USDKTD2824C5Y
USDKTD2824C5YP2
USDKTD2824YI
USDKTD3212C5Y
USDKTD3224C4YP2
Part #
57002
49639
42526
49628
57003
49640
42527
49629
57004
49641
42528
54492
57012
54496
54468
49630
57005
49642
42529
49631
57006
49643
42530
54493
57013
54469
77157
49632
57007
49644
42531
49633
57008
49645
42532
54494
57014
54498
49634
57009
49646
42533
49625
57000
49637
42524
49635
57010
49647
42534
54495
57015
54499
54471
80431
49636
57011
49648
42535
51700
57016
51703
51718
51701
57017
51704
51719
51702
57018
51705
49626
57001
49638
42525
49699
57040
49711
42550
49700
57041
49712
42551
49701
57042
49713
42552
57050
54520
49702
57043
49714
42553
49703
57044
49715
42554
57051
49704
bannerengineering.com
Pg Ref.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
Model
USDKTD3224C5Y
USDKTD3224C5YP2
USDKTD3224YI
USDKTD3624C4YP2
USDKTD3624C5Y
USDKTD3624C5YP2
USDKTD3624YI
USDKTD4012C5Y
USDKTD4024C4YP2
USDKTD4024C5Y
USDKTD4024C5YP2
USDKTD4024YI
USDKTD424C4YP2
USDKTD424C5Y
USDKTD424C5YP2
USDKTD424YI
USDKTD4424C4YP2
USDKTD4424C5Y
USDKTD4424C5YP2
USDKTD4424YI
USDKTD4812C4YP2
USDKTD4812C5Y
USDKTD4812YI
USDKTD4824C4YP2
USDKTD4824C5Y
USDKTD4824C5YP2
USDKTD4824YI
USDKTD5612C5Y
USDKTD5612YI
USDKTD6412C5Y
USDKTD7212C5Y
USDKTD7212C5YP2
USDKTD824C4YP2
USDKTD824C5Y
USDKTD824C5YP2
USDKTD824YI
USE1224Y
USE1224YI
USE1224YP2
USE1624Y
USE1624YI
USE1624YP2
USE2024Y
USE2024YI
USE2024YP2
USE2412Y
USE2412YI
USE2412YP2
USE2424Y
USE2424YI
USE2424YP2
USE2824Y
USE2824YI
USE2824YP2
USE3212Y
USE3212YI
USE3212YP2
USE3224Y
USE3224YI
USE3224YP2
USE3624Y
USE3624YI
USE3624YP2
USE4012Y
USE4012YI
USE4012YP2
USE4024Y
USE4024YI
USE4024YP2
USE424Y
USE424YI
USE424YP2
USE4424Y
USE4424YI
USE4424YP2
USE4812NI
USE4812Y
USE4812YI
USE4812YP2
USE4824Y
USE4824YI
USE4824YP2
USE5612Y
USE5612YI
USE5612YP2
USE6412Y
USE6412YI
USE6412YP2
USE7212Y
USE7212YI
USE7212YP2
USE824Y
USE824YI
USE824YP2
USK2CM2424L3C5Y
USK2D1224C4YP2
USK2D1224C5Y
USK2D1224C5YP2
Part #
57045
49716
42555
49705
57046
49717
42556
57052
49706
57047
49718
42557
49697
57038
49709
42548
49707
57048
49719
42558
54519
57053
54479
49708
57049
49720
42559
57054
51742
57055
57056
51729
49698
57039
49710
42549
55138
42504
49605
55140
42506
49607
55143
42508
49609
55159
54460
54452
55145
42510
49611
55147
42512
49613
55161
54462
54454
55149
42514
49615
55151
42516
49617
55163
54464
54456
55153
42518
49619
55134
42500
49601
55155
42520
49621
63576
55165
54466
54458
55157
42522
49623
55167
51314
51308
55169
51316
51310
55171
51318
51312
55136
42502
49603
77697
51548
57097
51563
“call” indicates call 1-888-373-6767
Pg Ref.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
287
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
INDEX
Model
USK2D1224YI
USK2D16243YI
USK2D1624C4YP2
USK2D1624C5Y
USK2D1624C5YP2
USK2D1624YI
USK2D2024C4YP2
USK2D2024C5Y
USK2D2024C5YP2
USK2D2024LC4Y
USK2D2024YI
USK2D24123C5Y
USK2D2412C5Y
USK2D2412C5YP2
USK2D2412YI
USK2D2424C4YP2
USK2D2424C5Y
USK2D2424C5YP2
USK2D2424YI
USK2D2824C4YP2
USK2D2824C5Y
USK2D2824C5YP2
USK2D2824YI
USK2D3212C5Y
USK2D3212YI
USK2D3224C4YP2
USK2D3224C5Y
USK2D3224C5YP2
USK2D3224YI
USK2D36243C5Y
USK2D3624C4YP2
USK2D3624C5Y
USK2D3624C5YP2
USK2D3624YI
USK2D4012C5Y
USK2D4012C5YP2
USK2D4024C4YP2
USK2D4024C5Y
USK2D4024C5YP2
USK2D4024YI
USK2D424C4YP2
USK2D424C5Y
USK2D424C5YP2
USK2D424YI
USK2D4424C4YP2
USK2D4424C5Y
USK2D4424C5YP2
USK2D4424YI
USK2D4812C5Y
USK2D4824C4YP2
USK2D4824C5Y
USK2D4824C5YP2
USK2D4824YI
USK2D5612C4YP2
USK2D5612C5Y
USK2D5612C5YP2
USK2D5612YI
USK2D6412C4YP2
USK2D6412C5Y
USK2D6412C5YP2
USK2D6412YI
USK2D7212C4YP2
USK2D7212C5Y
USK2D7212C5YP2
USK2D7212YI
USK2D824C4YP2
USK2D824C5Y
USK2D824C5YP2
USK2D824LC4Y
USK2D824YI
USK2T12243C5YP2
USK2T3624C4Y
USK2T40243C5Y
USK2T56123C5YP2
USKCM4824LYI
USKD1224C4YP2
USKD1224C5Y
USKD1224C5YP2
USKD1224YI
USKD1624C4YP2
USKD1624C5Y
USKD1624C5YP2
USKD1624YI
USKD20243C4Y
USKD2024C4YP2
USKD2024C5Y
USKD2024C5YP2
USKD2024YI
USKD2412C4YP2
USKD2412C5Y
USKD2412C5YP2
USKD2412YI
USKD2424C4YP2
USKD2424C5Y
USKD2424C5YP2
USKD2424YI
USKD2824C4YP2
USKD2824C5Y
288
Part #
51870
78894
51549
57098
51564
51871
51550
57099
51565
77550
51872
81665
57107
54556
54488
51551
57100
51566
51873
51552
57101
51567
51874
57108
54489
51553
57102
51568
51875
78406
51554
57103
51569
51876
57109
54558
51555
57104
51570
51877
51546
57095
51561
51868
51556
57105
51571
51878
57110
51557
57106
51572
51879
51558
57111
51573
51880
51559
57112
51574
51881
51560
57113
51575
51882
51547
57096
51562
77551
51869
80426
81277
77601
80530
79538
51503
57078
51518
51855
51504
57079
51519
51856
76999
51505
57080
51520
51857
54540
57088
54544
54484
51506
57081
51521
51858
51507
57082
Pg Ref.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
“w.o” indicates web only; visit
Model
USKD2824C5YP2
USKD2824YI
USKD3212C4YP2
USKD3212C5Y
USKD3212C5YP2
USKD3212YI
USKD3224C4Y
USKD3224C4YP2
USKD3224C5Y
USKD3224C5YP2
USKD3224YI
USKD3624C4YP2
USKD3624C5Y
USKD3624C5YP2
USKD3624YI
USKD40123C5YP2
USKD4012C4YP2
USKD4012C5Y
USKD4012C5YP2
USKD4012YI
USKD4024C4YP2
USKD4024C5Y
USKD4024C5YP2
USKD4024YI
USKD424C4YP2
USKD424C5Y
USKD424C5YP2
USKD424YI
USKD4424C4YP2
USKD4424C5Y
USKD4424C5YP2
USKD4424YI
USKD48123C5Y
USKD4812C4YP2
USKD4812C5Y
USKD4812C5YP2
USKD4812YI
USKD4824C4YP2
USKD4824C5Y
USKD4824C5YP2
USKD4824YI
USKD5612C4YP2
USKD5612C5Y
USKD5612C5YP2
USKD5612YI
USKD6412C4YP2
USKD6412C5Y
USKD6412C5YP2
USKD6412YI
USKD7212C4YP2
USKD7212C5Y
USKD7212C5YP2
USKD7212YI
USKD8243C4YP2
USKD824C4YP2
USKD824C5Y
USKD824C5YP2
USKD824YI
USMAB-1
USMAL-1
USMA-PSC-1
USMB-1
USMB-4
USMB-5
USMB-6
USMB-8
USR1224Y
USR1224YI
USR1224YP2
USR1624Y
USR1624YI
USR1624YP2
USR2024Y
USR2024YI
USR2024YP2
USR2412Y
USR2412YI
USR2412YP2
USR2424Y
USR2424YI
USR2424YP2
USR2824Y
USR2824YI
USR2824YP2
USR3212Y
USR3212YI
USR3212YP2
USR3224Y
USR3224YI
USR3224YP2
USR3624Y
USR3624YI
USR3624YP2
USR4012Y
USR4012YI
USR4012YP2
USR4024Y
USR4024YI
Part #
51522
51859
54541
57089
54545
54485
70407
51508
57083
51523
51860
51509
57084
51524
51861
77121
54542
57090
54546
54486
51510
57085
51525
51862
51501
57076
51516
51853
51511
57086
51526
51863
79925
54543
57091
54547
54487
51512
57087
51527
51864
51513
57092
51528
51865
51514
57093
51529
51866
51515
57094
51530
51867
79757
51502
57077
51517
51854
64734
60643
60642
50000
55668
55669
57140
75115
55139
42505
49606
55141
42507
49608
55144
42509
49610
55160
54461
54453
55146
42511
49612
55148
42513
49614
55162
54463
54455
55150
42515
49616
55152
42517
49618
55164
54465
54457
55154
42519
bannerengineering.com
Pg Ref.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
176
w.o.
w.o.
176
176
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
Model
USR4024YP2
USR424Y
USR424YI
USR424YP2
USR4424Y
USR4424YI
USR4424YP2
USR4812Y
USR4812YI
USR4812YP2
USR4824Y
USR4824YI
USR4824YP2
USR5612Y
USR5612YI
USR5612YP2
USR6412Y
USR6412YI
USR6412YP2
USR7212Y
USR7212YI
USR7212YP2
USR824Y
USR824YI
USR824YP2
USS12
USS16
USS20
USS24
USS28
USS32
USS36
USS4
USS40
USS44
USS48
USS56
USS64
USS72
USS8
US-XPE-32
US-XPE-43
UTB-3100C
UTB-3250C
UTB-325C
UTB-350C
UTB-5100C
UTB-5250C
UTB-525C
UTB-550C
UTB-8100C
UTB-8250C
UTB-825C
UTB-850C
Part #
49620
55135
42501
49602
55156
42521
49622
55166
54467
54459
55158
42523
49624
55168
51315
51309
55170
51317
51311
55172
51319
51313
55137
42503
49604
55118
55119
55120
55121
55122
55123
55124
55116
55125
55126
55127
55128
55129
55130
55117
63438
64214
69275
69276
69273
69274
69279
69280
69277
69278
69287
69288
69285
69286
Pg Ref.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
w.o.
186
186
186
186
186
186
186
186
186
186
186
186
“call” indicates call 1-888-373-6767
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Banner Engineering Corp.
9714 Tenth Avenue North
Minneapolis, Minnesota 55441
763-544-3164 • Fax: 763-544-3213
1-888-3-SENSOR (1-888-373-6767)
www.bannerengineering.com
email: [email protected]
Product Specifications and Modifications Disclaimer
All specifications published in this document are subject to change.
Banner reserves the right to modify the specifications of products,
prior to their order, without notice.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Safety
PRODUCTS
2009-2010
Safety Light Screen Systems
Safety Laser Scanners
Fiber Optic Safety Systems
Safety Controllers and Modules
Two-Hand Control Modules
Safety Interlock Switches
Emergency Stop Devices
Banner Engineering Corp.
9714 Tenth Avenue North
Minneapolis, Minnesota 55441
763-544-3164 • Fax: 763-544-3213
1-888-3-SENSOR (1-888-373-6767)
www.bannerengineering.com
email: [email protected]
P/N 141620
PRINTED IN USA
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement