Renesas H8SX/1520 Technical information

To our customers,
Old Company Name in Catalogs and Other Documents
On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology
Corporation, and Renesas Electronics Corporation took over all the business of both
companies. Therefore, although the old company name remains in this document, it is a valid
Renesas Electronics document. We appreciate your understanding.
Renesas Electronics website: http://www.renesas.com
April 1st, 2010
Renesas Electronics Corporation
Issued by: Renesas Electronics Corporation (http://www.renesas.com)
Send any inquiries to http://www.renesas.com/inquiry.
Notice
1.
2.
3.
4.
5.
6.
7.
All information included in this document is current as of the date this document is issued. Such information, however, is
subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please
confirm the latest product information with a Renesas Electronics sales office. Also, please pay regular and careful attention to
additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website.
Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights
of third parties by or arising from the use of Renesas Electronics products or technical information described in this document.
No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights
of Renesas Electronics or others.
You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part.
Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of
semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software,
and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by
you or third parties arising from the use of these circuits, software, or information.
When exporting the products or technology described in this document, you should comply with the applicable export control
laws and regulations and follow the procedures required by such laws and regulations. You should not use Renesas
Electronics products or the technology described in this document for any purpose relating to military applications or use by
the military, including but not limited to the development of weapons of mass destruction. Renesas Electronics products and
technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited
under any applicable domestic or foreign laws or regulations.
Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics
does not warrant that such information is error free. Renesas Electronics assumes no liability whatsoever for any damages
incurred by you resulting from errors in or omissions from the information included herein.
Renesas Electronics products are classified according to the following three quality grades: “Standard”, “High Quality”, and
“Specific”. The recommended applications for each Renesas Electronics product depends on the product’s quality grade, as
indicated below. You must check the quality grade of each Renesas Electronics product before using it in a particular
application. You may not use any Renesas Electronics product for any application categorized as “Specific” without the prior
written consent of Renesas Electronics. Further, you may not use any Renesas Electronics product for any application for
which it is not intended without the prior written consent of Renesas Electronics. Renesas Electronics shall not be in any way
liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an
application categorized as “Specific” or for which the product is not intended where you have failed to obtain the prior written
consent of Renesas Electronics. The quality grade of each Renesas Electronics product is “Standard” unless otherwise
expressly specified in a Renesas Electronics data sheets or data books, etc.
“Standard”:
8.
9.
10.
11.
12.
Computers; office equipment; communications equipment; test and measurement equipment; audio and visual
equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots.
“High Quality”: Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anticrime systems; safety equipment; and medical equipment not specifically designed for life support.
“Specific”:
Aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or
systems for life support (e.g. artificial life support devices or systems), surgical implantations, or healthcare
intervention (e.g. excision, etc.), and any other applications or purposes that pose a direct threat to human life.
You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics,
especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation
characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or
damages arising out of the use of Renesas Electronics products beyond such specified ranges.
Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have
specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further,
Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to
guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a
Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire
control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because
the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system
manufactured by you.
Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental
compatibility of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable
laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS
Directive. Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with
applicable laws and regulations.
This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of Renesas
Electronics.
Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this
document or Renesas Electronics products, or if you have any other inquiries.
(Note 1) “Renesas Electronics” as used in this document means Renesas Electronics Corporation and also includes its majorityowned subsidiaries.
(Note 2) “Renesas Electronics product(s)” means any product developed or manufactured by or for Renesas Electronics.
User’s Manual
H8SX/1520 Group FP-100M
User System Interface Cable
User’s Manual
Renesas Microcomputer
Development Environment
System
HS1527ECH61H
Rev.1.00 2005.01
Keep safety first in your circuit designs!
1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and
more reliable, but there is always the possibility that trouble may occur with them. Trouble with
semiconductors may lead to personal injury, fire or property damage.
Remember to give due consideration to safety when making your circuit designs, with appropriate
measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or
(iii) prevention against any malfunction or mishap.
Notes regarding these materials
1. These materials are intended as a reference to assist our customers in the selection of the Renesas
Technology Corp. product best suited to the customer's application; they do not convey any license
under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or
a third party.
2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any thirdparty's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or
circuit application examples contained in these materials.
3. All information contained in these materials, including product data, diagrams, charts, programs and
algorithms represents information on products at the time of publication of these materials, and are
subject to change by Renesas Technology Corp. without notice due to product improvements or
other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or
an authorized Renesas Technology Corp. product distributor for the latest product information
before purchasing a product listed herein.
The information described here may contain technical inaccuracies or typographical errors.
Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising
from these inaccuracies or errors.
Please also pay attention to information published by Renesas Technology Corp. by various means,
including the Renesas Technology Corp. Semiconductor home page (http://www.renesas.com).
4. When using any or all of the information contained in these materials, including product data,
diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total
system before making a final decision on the applicability of the information and products. Renesas
Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the
information contained herein.
5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or
system that is used under circumstances in which human life is potentially at stake. Please contact
Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when
considering the use of a product contained herein for any specific purposes, such as apparatus or
systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use.
6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in
whole or in part these materials.
7. If these products or technologies are subject to the Japanese export control restrictions, they must
be exported under a license from the Japanese government and cannot be imported into a country
other than the approved destination.
Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the
country of destination is prohibited.
8. Please contact Renesas Technology Corp. for further details on these materials or the products
contained therein.
Preface
The HS1527ECH61H is a user system interface cable that connects an H8SX/1520 group E6000H
emulator (HS1527KEPH60H; hereinafter referred to as the emulator) to the IC socket for an
FP-100M package for the H8SX/1520 group MCU on the user system.
i
Contents
Section 1
Configuration....................................................................................1
Section 2 Connection Procedures ......................................................................3
2.1
2.2
2.3
2.4
2.5
Connecting User System Interface Cable to Emulator Station .......................................... 3
Connecting User System Interface Cable to User System................................................. 5
2.2.1 Installing IC Socket.............................................................................................. 5
2.2.2 Soldering IC Socket ............................................................................................. 5
2.2.3 Inserting Cable Head............................................................................................ 6
2.2.4 Fastening Cable Head .......................................................................................... 6
2.2.5 Fastening Cable Body .......................................................................................... 8
Recommended Dimensions for User System Mount Pad .................................................. 9
Dimensions for User System Interface Cable Head .......................................................... 10
Resulting Dimensions after Connecting User System Interface Cable.............................. 11
Section 3 Installing the MCU to the User System .............................................12
Section 4 Verifying Operation...........................................................................14
Section 5 Notice.................................................................................................15
ii
Section 1 Configuration
CAUTION
Use an IC149-100-054-B51 socket (manufactured by
YAMAICHI ELECTRONICS Co., Ltd.) for the FP-100M package
IC socket on the user system.
Figure 1 shows the configuration of the HS1527ECH61H user system interface cable for the
FP-100M package.
To emulator station
Cable body
Screws (M2.6 x 12 mm)
with flat washers
(for fastening cable head)
Screws (M2.6 x 6 mm)
with flat washers
Socket cover
Cable head
IC socket
User system
Figure 1 HS1527ECH61H User System Interface Cable
1
Table 1 lists the HS1527ECH61H components. Please make sure you have all of these components
when unpacking.
Table 1
HS1527ECH61H Components
No. Component
Quantity
Remarks
1
Cable body
1
Cable
2
Cable head
1
3
IC socket
1
For the FP-100M package
4
Socket cover
1
For installing an FP-100M packaged MCU
5
Screws (M2.6 x 12 mm)
4
For fastening cable head (with four flat washers)
6
Screws (M2.6 x 6 mm)
4
For installing an FP-100M packaged MCU (with
four flat washers)
7
Documentation
1
User’s manual for HS1527ECH61H (this manual)
2
Section 2 Connection Procedures
2.1
Connecting User System Interface Cable to Emulator Station
WARNING
Observe the precautions listed below. Failure to do so
will result in a FIRE HAZARD and will damage the user
system and the emulator product or will result in
PERSONAL INJURY. The USER PROGRAM will be
LOST.
1. Always switch OFF the user system and the emulator
product before the USER SYSTEM INTERFACE CABLE
is connected to or removed from any part. Before
connecting, make sure that pin 1 on both sides are
correctly aligned.
2. The user system interface cable dedicated to the
emulator must be used.
To connect the cable body to the emulator station, follow the instructions below.
1. Make sure the user system and emulator station are turned off.
CAUTION
When connecting or removing the user system interface
cable, apply force only in the direction suitable for
connection or removal, while making sure not to bend or
twist the cable or connectors. Otherwise, the connectors
will be damaged.
3
2. After making sure the direction of the cable body connector is correct, firmly insert the cable
body connector into the emulator station socket (figure 2).
E6000H
RENESAS
HS1527KEPH60H
emulator station
Cable body connector
User system interface cable
Figure 2 Example of the HS1527KEPH60H Emulator Station
4
2.2
Connecting User System Interface Cable to User System
WARNING
Always switch OFF the user system and the emulator
product before the USER SYSTEM INTERFACE CABLE
is connected to or removed from any part. Before
connecting, make sure that pin 1 on both sides are correctly
aligned. Failure to do so will result in a FIRE HAZARD and
will damage the user system and the emulator product or
will result in PERSONAL INJURY. The USER PROGRAM will
be LOST.
To connect the cable head to the user system, follow the instructions below.
2.2.1
Installing IC Socket
After checking the location of pin 1 on the IC socket, apply epoxy resin adhesive to the bottom of the
IC socket for an FP-100M package, and fasten it to the user system before soldering.
2.2.2
Soldering IC Socket
After fastening, solder the IC socket for an FP-100M package to the user system. Be sure to
completely solder the leads so that the solder slops gently over the leads and forms solder fillets.
(Use slightly more solder than the MCU.)
5
2.2.3
Inserting Cable Head
CAUTION
Check the location of pin 1 before inserting.
Align pin 1 on the IC socket for an FP-100M package on the user system with pin 1 on the user
system interface cable head, and insert the user system interface cable head into the IC socket on the
user system, as shown in figure 3.
2.2.4
Fastening Cable Head
CAUTION
1. Use a Philips-type screwdriver whose head matches
the screw head.
2. The tightening torque must be 0.0785 N•m or less.
If the applied torque cannot be accurately measured,
stop tightening when the force required to turn the screw
becomes significantly greater than that needed when first
tightening. If a screw is tightened too much, the screw
head may break or an IC socket contact error may be
caused by a crack in the IC socket solder.
3. If the emulator does not operate correctly, cracks might
have occurred in the solder. Check conduction with
a tester and re-solder the IC socket if necessary.
6
Fasten the user system interface cable head to the IC socket for an FP-100M package on the user
system with the four screws (M2.6 x 12 mm; with four flat washers) provided. Each screw should be
tightened a little at a time, alternating between screws on opposing corners. Take special care, such
as manually securing the IC socket soldered area, to prevent the soldered IC socket from being
damaged by overtightening the screws or twisting the components.
Screws (M2.6 x 12 mm)
with flat washers
Cable head
Pin 1
User system
IC socket
(IC149-100-054-B51
manufactured by
YAMAICHI ELECTRONICS Co., Ltd.)
Figure 3 Connecting User System Interface Cable to User System
7
2.2.5
Fastening Cable Body
Connect the cable body to the cable head.
Cable body
Removing
Push the remove jigs
Remove jig
Cable head
User system
Figure 4 Fastening Cable Body
8
2.3
Recommended Dimensions for User System Mount Pad
Figure 5 shows the recommended dimensions for the mount pad (footprint) for the user system with
an IC socket for an FP-100M package (IC149-100-054-B51: manufactured by YAMAICHI
ELECTRONICS Co., Ltd.). Note that the dimensions in figure 5 are somewhat different from those
of the actual chip's mount pad.
17.10 (min.)
13.80 (max.)
0.5 x 24 = 12.00 ± 0.05
0.5 x 24 = 12.00 ± 0.05
0.30 ± 0.05
0.50 ± 0.05
0.50 ± 0.05
Unit: mm
Figure 5 Recommended Dimensions for Mount Pad
9
2.4
Dimensions for User System Interface Cable Head
29.5
66.04
The dimensions for the user system interface cable head are shown in figure 6.
17.0
29.5
17.0
63.50
Unit: mm
Tolerance: ±0.5 mm
Figure 6 Dimensions for User System Interface Cable Head
10
2.5
Resulting Dimensions after Connecting User System Interface Cable
21.5
The resulting dimensions, after connecting the user system interface cable head to the user system,
are shown in figure 7.
16.0
Cable head
User system
IC socket
(IC149-100-054-B51
manufactured by
YAMAICHI ELECTRONICS Co. Ltd.)
Unit: mm
Tolerance: ±0.5 mm
Figure 7 Resulting Dimensions after Connecting User System Interface Cable
11
Section 3 Installing the MCU to the User System
CAUTION
1. Check the location of pin 1 before inserting.
2. Use a Philips-type screwdriver whose head matches
the screw head.
3. The tightening torque must be 0.0785 N•m or less.
If the applied torque cannot be accurately measured,
stop tightening when the force required to turn the screw
becomes significantly greater than that needed when first
tightening. If a screw is tightened too much, the screw
head may break or an IC socket contact error may be
caused by a crack in the IC socket solder.
4. If the MCU does not operate correctly, cracks might have
occurred in the solder. Check conduction with a tester
and re-solder the IC socket if necessary.
Check the location of pin 1 before inserting the MCU into the IC socket on the user system, as shown
in figure 8. After inserting the MCU, fasten the socket cover with the provided four screws (M2.6 x
6 mm; with four flat washers). Take special care, such as manually securing the IC socket soldered
area, to prevent the IC socket from being damaged by overtightening the screws or twisting the
components.
12
Screws (M2.6 x 6 mm)
with flat washers
Socket cover
MCU
Pin 1
IC socket
(IC149-100-054-B51
manufactured by
YAMAICHI ELECTRONICS Co., Ltd.)
User system
Figure 8 Installing MCU to User System
13
Section 4 Verifying Operation
1. Turn on the emulator according to the procedures described in the H8SX/1650 E6000H Emulator
User's Manual (HS1650EPH60HE).
2. Verify the user system interface cable connections by checking the pin states with the CHECK
command (emulator command). If an error is detected, recheck the soldered IC socket and the
location of pin 1.
3. The emulator connected to this user system interface cable supports three kinds of clock sources
as the MCU clock: an emulator internal clock, an external clock on the user system, and a crystal
oscillator to be mounted on the EV-chip board. For details, refer to the H8SX/1650 E6000H
Emulator User's Manual (HS1650EPH60HE).
 To use the emulator internal clock
Select the clock in the emulator by using the CLOCK command (emulator command).
 To use the external clock on the user system
Select the external clock with the CLOCK command (emulator command). Supply the
external clock from the user system to the emulator by inputting the external clock from the
EXTAL terminal on the cable head or connecting a crystal oscillator to the EXTAL and
XTAL terminals. For details, refer to the H8SX/1520 Group Hardware Manual.
 To use the crystal oscillator mounted on the EV-chip board
Install a crystal oscillator into the crystal oscillator terminals on the EV-chip board.
Figure 9 shows the oscillator circuit on the user system interface cable.
1 MΩ
HCU04
HCU04
EXTAL
To E6000H
emulator
270 Ω
XTAL
Figure 9 Oscillator Circuit
14
Section 5 Notice
1. Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head
before inserting the cable head into the user system IC socket.
2. This user system interface cable is specifically designed for the HS1527KEPH60H emulator. Do
not use this cable with any other emulator station.
3. To prevent breaking of wires in the cable body, do not place heavy or sharp metal objects on the
user system interface cable.
4. While the emulator station is connected to the user system with the user system interface cable,
force must not be applied to the cable head. Place the emulator station, user system interface
cable, and user system as shown in the example in figure 10.
Place components so that the cable body and cable head are
parallel to the user system.
Emulator's front-end unit
Cable
Cable head is parallel
to emulator station
Cable head is parallel
to user system
User system
Figure 10 User System Interface Cable Location Example
5.
The P1 short connector is used for testing. Do not remove the jumper pin that is inserted in
the side of pins 1 and 2.
1 P4 3
3
1
P1
Figure 11 P1 and P4 Short Connectors
15
6. A level-shift circuit with AVcc0 and AVcc1 is mounted on the user system interface cable, as
shown in figure 12. At shipment, the jumper pin is inserted in the side of pins 1 and 2 of the P4
short connector. For details on the differences between the target MCU and the emulator, refer to
the H8SX/1650 E6000H Emulator User's Manual (HS1650EPH60HE). For the ranges of input
voltages of AVcc0 and AVcc1, refer to the H8SX/1520 Group Hardware Manual.
CAUTION
Insert the jumper pin in the P4 short connector so that
the higher voltage between AVcc0 and AVcc1 is selected.
Select either AVcc0 or AVcc1 when their potentials are
the same. Do not use the emulator without jumper pins.
User system interface
Emulator station
AVcc0
5V
1.03 k
+
UVREF3
2k
AVss
1
AVcc1
5V
3
1.03 k
P4
+
AVcc of MCU
of the emulator
station
UVREF1
2k
AVss
Settings of short connector:
Between pins 1 and 2: AVcc0
Between pins 2 and 3: AVcc1
Figure 12 Level-shift Circuit with AVcc0 and AVcc1
16
Renesas Microcomputer Development Environment System
User's Manual
H8SX/1520 Group FP-100M User System Interface Cable
Publication Date: Rev.1.00, January 12, 2005
Published by:
Sales Strategic Planning Div.
Renesas Technology Corp.
Edited by:
Technical Documentation & Information Department
Renesas Kodaira Semiconductor Co., Ltd.
 2005. Renesas Technology Corp., All rights reserved. Printed in Japan.
Sales Strategic Planning Div.
Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
RENESAS SALES OFFICES
http://www.renesas.com
Refer to "http://www.renesas.com/en/network" for the latest and detailed information.
Renesas Technology America, Inc.
450 Holger Way, San Jose, CA 95134-1368, U.S.A
Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501
Renesas Technology Europe Limited
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K.
Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900
Renesas Technology Hong Kong Ltd.
7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong
Tel: <852> 2265-6688, Fax: <852> 2730-6071
Renesas Technology Taiwan Co., Ltd.
10th Floor, No.99, Fushing North Road, Taipei, Taiwan
Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999
Renesas Technology (Shanghai) Co., Ltd.
Unit2607 Ruijing Building, No.205 Maoming Road (S), Shanghai 200020, China
Tel: <86> (21) 6472-1001, Fax: <86> (21) 6415-2952
Renesas Technology Singapore Pte. Ltd.
1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632
Tel: <65> 6213-0200, Fax: <65> 6278-8001
Colophon 2.0
H8SX/1520 Group FP-100M
User System Interface Cable
HS1527ECH61H User’s Manual
1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 Japan
REJ10B0173-0100