MODEL Platinum
(Machine Code: C267)
SERVICE MANUAL
IMPORTANT SAFETY NOTICES
PREVENTION OF PHYSICAL INJURY
1. Before disassembling or assembling parts of the printer and peripherals,
make sure that the power cord is unplugged.
2. The wall outlet should be near the printer and easily accessible.
3. If any adjustment or operation check has to be made with exterior covers off
or open while the main switch is turned on, keep hands away from electrified
or mechanically driven components.
HEALTH SAFETY CONDITIONS
1. If you get ink in your eyes by accident, try to remove it with eye drops or
flush with water as first aid. If unsuccessful, get medical attention.
2. If you ingest ink by accident, induce vomiting by sticking a finger down your
throat or by giving soapy or strong salty water to drink.
OBSERVANCE OF ELECTRICAL SAFETY STANDARDS
1. The printer and its peripherals must be installed and maintained by a
customer service representative who has completed the training course on
those models.
SAFETY AND ECOLOGICAL NOTES FOR DISPOSAL
1. Dispose of replaced parts in accordance with local regulations.
2. Used ink and masters should be disposed of in an environmentally safe
manner and in accordance with local regulations.
1
Symbols
This manual uses several symbols. The meaning of those symbols are as follows:
☛
See or Refer to
Core tech manual
Clip ring
E-ring
Screw
Connector
Short Edge Feed (SEF)
Long Edge Feed (LEF)
2
TABLE OF CONTENTS
1. INSTALLATION .......................................................................... 1-1
1.1 INSTALLATION REQUIREMENTS ...........................................................1-1
1.1.1 OPTIMUM ENVIRONMENTAL CONDITION....................................1-1
1.1.2 ENVIRONMENTS TO AVOID...........................................................1-1
1.1.3 POWER CONNECTION ...................................................................1-1
1.1.4 MINIMUM SPACE REQUIREMENTS...............................................1-2
1.1.5 DIMENSIONS ...................................................................................1-2
1.1.6 MAIN BODY AND PERIPHERALS ...................................................1-3
1.1.7 POWER SOCKETS FOR PERIPHERALS .......................................1-4
1.2 INSTALLATION PROCEDURE .................................................................1-5
1.2.1 MAIN BODY .....................................................................................1-5
Accessory Check ..................................................................................1-5
Installation Procedure ...........................................................................1-6
Changing the operation panel language .............................................1-13
Date/Time Setting ...............................................................................1-13
SP Codes Setting................................................................................1-13
1.2.2 COLOR DRUM (OPTION) ..............................................................1-14
Accessory Check ................................................................................1-14
Installation Procedure .........................................................................1-14
1.2.3 ADF (OPTION) ...............................................................................1-15
Accessory Check ................................................................................1-15
Installation Procedure .........................................................................1-16
1.2.4 PLATEN COVER (OPTION)...........................................................1-18
Accessory Check ................................................................................1-18
Installation Procedure .........................................................................1-18
1.2.5 TAPE DISPENSER (OPTION) .......................................................1-19
Accessory Check ................................................................................1-19
Installation Procedure .........................................................................1-19
1.2.6 PRINTER UNIT VC-20 (OPTION) ..................................................1-23
Accessory Check ................................................................................1-23
Installation Procedure .........................................................................1-24
2. PREVENTIVE MAINTENANCE................................................... 2-1
ADF.......................................................................................................2-2
3. REPLACEMENT AND ADJUSTMENT........................................ 3-1
3.1 GENERAL CAUTION ................................................................................3-1
3.2 COVERS ...................................................................................................3-1
3.2.1 FRONT COVER / FRONT DOOR.....................................................3-1
3.2.2 OPERATION PANEL........................................................................3-2
3.2.3 REAR COVER..................................................................................3-2
3.2.4 UPPER COVERS .............................................................................3-3
3.3 BOARDS ...................................................................................................3-4
3.3.1 MPU..................................................................................................3-4
3.3.2 PSU ..................................................................................................3-5
i
PSU board ............................................................................................3-5
PSU board with bracket ........................................................................3-5
3.4 SCANNER .................................................................................................3-6
3.4.1 EXPOSURE GLASS/DF EXPOSURE GLASS, SCALES .................3-6
Exposure Glass ....................................................................................3-6
DF Exposure Glass...............................................................................3-6
3.4.2 LENS BLOCK ...................................................................................3-7
3.4.3 EXPOSURE LAMP, LAMP STABILIZER BOARD ............................3-8
3.4.4 SCANNER MOTOR..........................................................................3-9
3.4.5 SCANNER HOME POSITION SENSOR ..........................................3-9
3.4.6 PLATEN COVER SENSOR............................................................3-10
3.4.7 ADJUSTING THE SCANNER POSITION.......................................3-11
Overview.............................................................................................3-11
Adjusting the Belt Contact Points for the First Scanner ......................3-12
Adjusting the Belt Contact Points for the Second Scanner .................3-13
3.5 MASTER FEED .......................................................................................3-15
3.5.1 MASTER MAKING UNIT ................................................................3-15
3.5.2 MASTER MAKING UNIT SET SWITCHES ....................................3-15
3.5.3 THERMAL HEAD............................................................................3-17
Installation...........................................................................................3-18
3.5.4 MASTER SET COVER SENSOR ...................................................3-19
3.5.5 MASTER END SENSOR ................................................................3-19
3.5.6 CUTTER UNIT................................................................................3-20
3.5.7 THERMAL HEAD VOLTAGE ADJUSTMENT.................................3-21
3.5.8 MASTER END SENSOR ADJUSTMENT .......................................3-22
3.6 MASTER EJECT .....................................................................................3-23
3.6.1 MASTER EJECT UNIT ...................................................................3-23
3.6.2 MASTER EJECT ROLLERS...........................................................3-24
3.6.3 MASTER EJECT MOTOR / PRESSURE PLATE MOTOR.............3-24
3.6.4 DRUM MASTER SENSOR / MASTER EJECT SENSOR /
EJECT BOX SET SENSOR............................................................3-25
3.6.5 PRESSURE PLATE HP SENSOR / PRESSURE
PLATE LIMIT SENSOR ..................................................................3-26
3.6.6 AIR KNIFE FAN MOTOR................................................................3-26
3.6.7 MASTER EJECT POSITION SENSOR ..........................................3-27
3.6.8 MASTER CLAMPER OPENING UNIT............................................3-27
3.7 PAPER FEED..........................................................................................3-28
3.7.1 PICK-UP ROLLER / PAPER FEED ROLLER / FRICTION PAD.....3-28
3.7.2 PAPER TABLE LOWER LIMIT SENSOR.......................................3-29
3.7.3 PAPER HEIGHT SENSOR 1 / 2.....................................................3-30
3.7.4 PAPER END SENSOR...................................................................3-31
3.7.5 PAPER TABLE MOTOR.................................................................3-32
3.7.6 PAPER FEED CLUTCH .................................................................3-32
3.7.7 PAPER SEPARATION PRESSURE ADJUSTMENT......................3-33
3.8 PRINTING ...............................................................................................3-34
3.8.1 PRESS ROLLER ............................................................................3-34
3.8.2 REGISTRATION SENSOR.............................................................3-35
3.8.3 FEED START TIMING SENSOR....................................................3-35
3.8.4 2ND FEED TIMING SENSOR ........................................................3-36
ii
3.8.5 REGISTRATION MOTOR ..............................................................3-37
3.8.6 REGISTRATION ROLLER .............................................................3-38
3.8.7 PRESS ROLLER RELEASE SOLENOIDS.....................................3-40
3.8.8 PRESS ROLLER RELEASE LEVER ADJUSTMENT .....................3-41
3.8.9 PRINTING PRESSURE ADJUSTMENT.........................................3-42
3.9 DRUM......................................................................................................3-43
3.9.1 PREPARATION..............................................................................3-43
3.9.2 CLOTH SCREEN............................................................................3-43
Installation...........................................................................................3-44
3.9.3 CLAMPER / METAL SCREEN .......................................................3-46
Installation...........................................................................................3-47
3.9.4 INK PUMP UNIT .............................................................................3-48
3.9.5 INK ROLLER UNIT / INK ROLLER ONE-WAY CLUTCH ...............3-49
3.9.6 DOCTOR ROLLER GAP ADJUSTMENT .......................................3-51
3.9.7 INK DETECTION ADJUSTMENT ...................................................3-52
Using an Oscilloscope ........................................................................3-52
Simple Method....................................................................................3-53
3.10 PAPER DELIVERY................................................................................3-54
3.10.1 PAPER DELIVERY UNIT .............................................................3-54
3.10.2 DELIVERY BELT / PAPER EXIT SENSOR / VACUUM
FAN MOTOR / PAPER DELIVERY UNIT BUSHINGS .................3-56
3.10.3 EXIT PAWL ADJUSTMENT .........................................................3-57
Clearance adjustment .........................................................................3-57
Timing adjustment...............................................................................3-58
3.11 MAIN DRIVE..........................................................................................3-60
3.11.1 MAIN MOTOR ..............................................................................3-60
3.11.2 MAIN DRIVE TIMING BELT ADJUSTMENT ................................3-63
3.11.3 MAIN MOTOR PULLEY POSITION..............................................3-64
3.12 FIRMWARE UPDATE (I/O ROM) ..........................................................3-65
3.13 SPECIAL TOOLS ............................................................................3-65
3.14 COLOR DRUM ......................................................................................3-66
3.14.1 INK PUMP ADJUSTMENT ...........................................................3-66
4. TROUBLESHOOTING ................................................................ 4-1
4.1 SERVICE CALL CODES ...........................................................................4-1
4.2 ELECTRICAL COMPONENT DEFECTS ..................................................4-3
4.2.1 DRUM...............................................................................................4-3
4.2.2 PAPER EJECT .................................................................................4-4
4.2.3 PAPER FEED...................................................................................4-4
4.2.4 MAIN DRIVE.....................................................................................4-4
4.2.5 SCANNER ........................................................................................4-4
4.2.6 MASTER EJECT ..............................................................................4-5
4.2.7 MASTER MAKING UNIT ..................................................................4-5
4.2.8 OTHER .............................................................................................4-6
4.3 DIP SW, LED, VR, TP, AND FUSE TABLES.............................................4-7
4.3.1 TEST POINTS ..................................................................................4-7
MPU......................................................................................................4-7
4.3.2 POTENTIOMETERS ........................................................................4-7
MPU......................................................................................................4-7
iii
Power Supply Unit ................................................................................4-7
4.3.3 LED'S................................................................................................4-7
FUSES..................................................................................................4-8
MPU......................................................................................................4-8
PSU ......................................................................................................4-8
5. SERVICE PROGRAM MODE...................................................... 5-1
5.1 USING SERVICE PROGRAM MODES.....................................................5-1
5.1.1 ACCESSING SP MODES.................................................................5-1
Entering SP Mode.................................................................................5-1
Leaving SP Mode..................................................................................5-1
5.1.2 HOW TO SELECT A PROGRAM NUMBER.....................................5-2
5.1.3 MAIN MENU NUMBER LIST ............................................................5-2
5.2 1. COPY DATA..........................................................................................5-3
5.2.1 SP TABLE (SP 1-XXX) .....................................................................5-3
5.2.2 SP1-70: MAIN FIRMWARE PARTS NUMBER.................................5-3
5.2.3 SP1-80: ERROR CODE HISTORY...................................................5-3
5.2.4 SP1-83: PSU UNUSUAL VOLTAGE HISTORY ...............................5-3
5.3 2. BASIC SETTINGS.................................................................................5-4
5.3.1 SP TABLE (SP 2-XXX) .....................................................................5-4
5.3.2 SP2-6: IMAGE POSITION DISPLAY ................................................5-5
5.3.3 SP2-33: RE-FEEDING SETTING .....................................................5-5
5.3.4 SP2-40, 2-55: THERMAL HEAD ENERGY CONTROL ....................5-5
5.3.5 SP2-60: BOLD MODE: LETTER MODE ONLY ................................5-5
5.3.6 SP2-61: T/H SWING MODE .............................................................5-5
5.3.7 SP2-62: T/H SWING AMOUNT ........................................................5-6
5.3.8 SP2-80: AUTO OFF AT UNUSUAL VOLTAGE ................................5-6
5.3.9 SP2-95: PAPER TABLE STANDBY POSITION. ..............................5-6
5.3.10 SP2-100: MAKE MASTER WITHOUT PRINT ................................5-6
5.4 3. SYSTEM SETTINGS .............................................................................5-7
5.4.1 SP TABLE (SP 3-XXX) .....................................................................5-7
5.4.2 SP3-1: INPUT THE PRESENT TIME ...............................................5-7
5.4.3 SP3-4: INPUT INSTALLATION DATE ..............................................5-8
5.5 4. INPUT MODE ........................................................................................5-9
5.5.1 SP TABLE (SP 4-XXX) .....................................................................5-9
5.6 5. OUTPUT MODE ..................................................................................5-10
5.6.1 SP TABLE (SP 5-XXX) ...................................................................5-10
5.7 6. ADJUSTMENT ....................................................................................5-11
5.7.1 SP TABLE (SP 6-XXX) ...................................................................5-11
5.7.2 SP6-10: MASTER WRITING SPEED .............................................5-13
5.7.3 SP6-21: PAPER REGIST POSITION .............................................5-14
5.7.4 SP6-5: SCANNING SPEED – PLATEN AND SP6-6:
SCANNING SPEED – ADF MODE.................................................5-14
5.7.5 SP6-3: SCANNING START POSITION – PLATEN AND
SP6-4: SCANNING START POSITION - ADF................................5-14
5.7.6 SP6-1: MAIN SCAN POSITION – PLATEN AND
SP6-2: MAIN SCAN POSITION - ADF ...........................................5-15
5.7.7 IMAGE ADJUSTMENT (SP6-10, -21, -5, -3, AND -1).....................5-15
5.7.8 SP6-20: REGISTRATION BUCKLE................................................5-15
iv
5.7.9 SP6-32 TO 37: MTF FILTER ..........................................................5-16
5.7.10 SP6-40: INK DETECTION ADJUSTMENT ...................................5-16
5.7.11 SP6-100 TO 104: PAPER REGISTRATION - EACH SPEED.......5-17
5.8 7. MEMORY CLEAR ...............................................................................5-18
5.8.1 SP TABLE (SP 7-XXX) ...................................................................5-18
5.8.2 SP7-1: FACTORY SETTINGS CLEAR...........................................5-18
5.8.3 SP7-3: TOTAL COUNTER CLEAR.................................................5-18
5.9 8. SYSTEM TEST....................................................................................5-19
5.9.1 SP TABLE (SP 8-XXX) ...................................................................5-19
5.9.2 SP8-1. DOWNLOAD MAIN FIRMWARE ........................................5-20
5.9.3 SP8-2: UPLOAD MAIN FIRMWARE...............................................5-20
5.9.4 SP8-9 DATA PRINTOUT – POWER FAILURE ..............................5-21
5.9.5 SP8-10: TEST PATTERNS ............................................................5-22
5.9.6 SP8-21: PAPER FEED TEST (30 RPM).........................................5-22
5.9.7 SP8-22: FREE RUN PAPER FEED (30 RPM) ...............................5-22
5.10 USER TOOLS .......................................................................................5-23
5.10.1 MAIN MENU NUMBER LIST ........................................................5-23
5.10.2 USER TOOL LISTS ......................................................................5-23
1. Counter.............................................................................................5-23
2. System..............................................................................................5-23
3. Set Operation Mode..........................................................................5-24
4. Initial Settings ...................................................................................5-24
5. Mode Settings...................................................................................5-25
6. Administrator Tools...........................................................................5-25
7. Online Settings .................................................................................5-25
6. DETAILED SECTION DESCRIPTIONS ...................................... 6-1
6.1 MECHANICAL COMPONENT LAYOUT ...................................................6-1
6.2 ELECTRICAL COMPONENT LAYOUT.....................................................6-2
6.2.1 MAIN BODY .....................................................................................6-2
Boards ..................................................................................................6-3
Motors...................................................................................................6-3
Solenoids ..............................................................................................6-3
Switches ...............................................................................................6-3
Sensors.................................................................................................6-4
Others ...................................................................................................6-4
6.3 DRIVE LAYOUT ........................................................................................6-5
6.4 SCANNER AND OPTICS ..........................................................................6-6
6.4.1 SCANNER OVERVIEW....................................................................6-6
Lamp Stabilizer Fuse ............................................................................6-6
6.4.2 SCANNER DRIVE ............................................................................6-7
6.5 IMAGE PROCESSING ..............................................................................6-8
6.5.1 IMAGE PROCESSING FLOW ..........................................................6-8
Shading Correction: ..............................................................................6-8
Reduce / Enlarge: .................................................................................6-8
Filtering: ................................................................................................6-8
Gamma Correction:...............................................................................6-8
Grayscale Processing: ..........................................................................6-8
6.5.2 THERMAL HEAD..............................................................................6-9
v
SPECIFICATIONS............................................................................ 6-9
Thermal Head Control...........................................................................6-9
Thermal Head Protection ......................................................................6-9
6.6 MASTER EJECT UNIT............................................................................6-10
6.6.1 OVERVIEW ....................................................................................6-10
Procedure ...........................................................................................6-10
6.6.2 MASTER EJECT UNIT OPEN MECHANISM .................................6-11
6.6.3 MASTER CLAMPER OPENING MECHANISM ..............................6-12
Clamper Mechanism ...........................................................................6-12
6.6.4 MASTER EJECT ROLLER MECHANISM ......................................6-13
Mechanism .........................................................................................6-13
6.6.5 PRESSURE PLATE MECHANISM.................................................6-14
Mechanism .........................................................................................6-14
Procedure ...........................................................................................6-14
6.7 MASTER FEED .......................................................................................6-15
6.7.1 OVERVIEW ....................................................................................6-15
Procedure ...........................................................................................6-15
6.7.2 MASTER FEED MECHANISM .......................................................6-16
Mechanism .........................................................................................6-16
Procedure ...........................................................................................6-16
6.7.3 CLAMPER AND TENSION ROLLER MECHANISM.......................6-17
Mechanism .........................................................................................6-18
Procedure ...........................................................................................6-18
6.7.4 CUTTER MECHANISM ..................................................................6-19
6.7.5 MASTER SET COVER SENSOR ...................................................6-20
6.7.6 MASTER MAKING UNIT SLIDE-OUT MECHANISM .....................6-21
6.7.7 MASTER SET MECHANISM..........................................................6-22
6.8 DRUM......................................................................................................6-23
6.8.1 OVERVIEW ....................................................................................6-23
Procedure ...........................................................................................6-23
6.8.2 DRUM DRIVE MECHANISM ..........................................................6-24
Mechanism .........................................................................................6-24
6.8.3 INK SUPPLY MECHANISM............................................................6-25
6.8.4 INK ROLLER MECHANISM ...........................................................6-26
6.8.5 INK SUPPLY CONTROL ................................................................6-27
Mechanism .........................................................................................6-27
Automatic Ink Supply for a New Drum ................................................6-28
6.8.6 DETECTION OF MASTERS ON THE DRUM ................................6-29
6.8.7 METAL SCREEN............................................................................6-30
6.8.8 DRUM TYPE DETECTION.............................................................6-31
Black drum..........................................................................................6-31
Color drum ..........................................................................................6-31
6.9 PAPER FEED..........................................................................................6-32
6.9.1 OVERALL .......................................................................................6-32
6.9.2 PAPER FEED MECHANISM ..........................................................6-33
6.9.3 PAPER FEED/SEPARATION PRESSURE
ADJUSTMENT MECHANISM.........................................................6-34
6.9.4 SIDE EDGE PAPER PRESS PLATE MECHANISM.......................6-35
6.9.5 REGISTRATION ROLLER MECHANISM.......................................6-36
vi
6.9.6 PAPER FEED RETRY MECHANISM .............................................6-36
6.9.7 REGISTRATION ROLLER UP/DOWN MECHANISM ....................6-37
6.9.8 REGISTRATION SENSOR CLEANING .........................................6-38
6.9.9 PRINTING PRESSURE MECHANISM ...........................................6-39
6.9.10 PAPER TABLE MECHANISM ......................................................6-40
Table Up and Down Mechanism.........................................................6-40
Paper End Detection Mechanism .......................................................6-41
Paper Size Detection ..........................................................................6-41
6.9.11 PAPER TABLE SIDE FENCE MECHANISM................................6-42
Paper Table Side-to-Side Shift Mechanism ........................................6-42
Side Fence Friction Pads....................................................................6-43
6.10 PAPER DELIVERY................................................................................6-44
6.10.1 OVERALL .....................................................................................6-44
Procedure ...........................................................................................6-44
6.10.2 PAPER DELIVERY UNIT DRIVE MECHANISM...........................6-45
Mechanism .........................................................................................6-45
6.10.3 PAPER SEPARATION FROM DRUM ..........................................6-46
Air knife...............................................................................................6-46
6.10.4 EXIT PAWL DRIVE MECHANISM................................................6-47
6.10.5 SIDE PLATE GUIDE.....................................................................6-49
6.11 ABNORMAL VOLTAGE PROTECTION ................................................6-50
Momentary voltage drop .....................................................................6-50
Low voltage (less than 150V)..............................................................6-50
High voltage ........................................................................................6-50
Over voltage (More than AC400V)......................................................6-50
General Notes on this Feature............................................................6-51
6.12 ERROR DETECTION............................................................................6-52
6.12.1 MASTER EJECT JAM (E JAM LOCATION INDICATOR) ............6-52
Picking up the used master from the drum .........................................6-52
Compressing the used master ............................................................6-52
Just after turning on the main switch...................................................6-52
6.12.2 ADF JAM (P JAM LOCATION INDICATOR) ................................6-53
Feeding in the original (ADF) ..............................................................6-53
Just after turning on the main switch...................................................6-53
6.12.3 MASTER FEED JAM (D JAM LOCATION INDICATOR) ..............6-54
Cutting the master...............................................................................6-54
Clamping the master...........................................................................6-54
6.12.4 PAPER FEED JAM (A JAM LOCATION INDICATOR + ) + Z) .....6-55
Paper feed ..........................................................................................6-55
6.12.5 PAPER DELIVERY JAM (C JAM LOCATION INDICATOR).........6-55
Paper delivery.....................................................................................6-55
6.13 TIMING CHART.....................................................................................6-56
6.13.1 SCANNING...................................................................................6-56
6.13.2 MASTER EJECT ..........................................................................6-56
6.13.3 MASTER FEED ............................................................................6-57
6.13.4 PRINT...........................................................................................6-58
vii
7. SPECIFICATIONS....................................................................... 7-1
7.1 ESSENTIAL DIFFERENCES BETWEEN C248 AND C267 MODELS ......7-1
7.2 ESSENTIAL DIFFERENCES BETWEEN C252 AND C267 MODELS ......7-2
7.3 GENERAL SPECIFICATIONS....................................................................7-3
viii
INSTALLATION REQUIREMENTS
1. INSTALLATION
1.1 INSTALLATION REQUIREMENTS
Carefully select the installation location because environmental conditions greatly
affect machine performance.
1.1.1 OPTIMUM ENVIRONMENTAL CONDITION
1. Temperature: 10 to 30 C (50 to 86 F)
2. Humidity: 20 to 90 %RH
3. Install the machine on a strong and level base. The machine must be level
within 5mm (0.2") both front to rear left to right.
1.1.2 ENVIRONMENTS TO AVOID
1. Locations exposed to direct sunlight or strong light (more than 1,500 lux).
2. Dusty areas
3. Areas containing corrosive gases.
4. Locations directly exposed to cool air from an air conditioner or reflected heat
from a space heater. (Sudden temperature changes from low to high or vice
versa may cause condensation within the machine.)
1.1.3 POWER CONNECTION
1. Securely connect the power cord to a power source.
2. Make sure that the wall outlet is near the machine and easily accessible.
3. Make sure the plug is firmly inserted in the outlet.
4. Avoid multi-wiring
5. Do not pinch the power cord.
1-1
Installation
28 March 2006
INSTALLATION REQUIREMENTS
28 March 2006
1.1.4 MINIMUM SPACE REQUIREMENTS
Place the machine near a power source, providing minimum clearance as shown
below.
200 mm (7.9") Rear
600 mm (23.6") Right
600 mm (23.6") Left
1.1.5 DIMENSIONS
600 mm (23.6") Front
C267I156.WMF
750 mm (29.5")
686 mm (27.0")
with ADF
633 mm (24.9")
1224 mm (49.0")
C267I904.WMF
663 mm (26.6")
C267I158.WMF
1-2
28 March 2006
INSTALLATION REQUIREMENTS
This is a list of the peripheral devices that can be installed with the digital duplicator.
2
3
6
5
1
4
C267I159.WMF
No.
1
2
3
4
5
6
Model
C267
C642
B406
C643/C647/C648
C651
C646
Name
Digital duplicator
ADF
Platen cover
Color drum
Tape Dispenser
Printer unit VC-20
1-3
Comments
Main Machine
Auto document feeder
Optional drum – A4/LG/B4
Printer controller unit
Installation
1.1.6 MAIN BODY AND PERIPHERALS
INSTALLATION REQUIREMENTS
28 March 2006
1.1.7 POWER SOCKETS FOR PERIPHERALS
CAUTION
Rating Voltage for Peripherals
Make sure to plug the cables into the correct sockets.
ADF
“ Rating Voltage of Output
Connector for Accessory:
Max. DC 24 V”
Tape Dispenser
“ Rating Voltage of Output
Connector for Accessory:
Max. DC 24 V”
C267I104.WMF
1-4
28 March 2006
INSTALLATION PROCEDURE
Installation
1.2 INSTALLATION PROCEDURE
1.2.1 MAIN BODY
Accessory Check
2
1
3
C267I108.WMF
Make sure that you have all the accessories listed below.
Description
Quantity
1. Master Spool .......................................................................2
2. Paper Delivery Table Side Plate Guide ...............................2
3. Paper Feed Side Pad ..........................................................2
4. Emblem Cover (C267-80, -83, -92, -93) ..............................1
5. Emblem – Ricoh DX 3440 (C267-80) ..................................1
6. Emblem – Gestetner DX 3440 (C267-80)............................1
7. Warranty Letter on carton box (C267-76, -78).....................1
8. Leaflet (C267-76, -78) .........................................................1
9. Operating Instructions (C267-61, -76, -78, -80, -92)............1
10. Easy Operation Guide (C267-61, -76, -78, -80, -92) .........1
11. German Acoustic Statement – Ricoh (C267-83, -93) ........1
12. German Acoustic Statement – Gestetner (C267-83, -93)..1
13. Bundled Items List (C267-76, -78).....................................1
14. NECR (C267-80, -92) ........................................................1
1-5
INSTALLATION PROCEDURE
28 March 2006
Installation Procedure
CAUTION
To avoid serious injury, do not connect the power plug to the machine until
you are instructed to do so.
C267I102.WMF
1. Unpack the machine and remove all the wrapping.
[E]
[C]
[A]
[D]
[C]
C267R084.WMF
[B]
2. When you install the optional table:
• Mount the machine on the table. There are two screws [A] packed with the
table.
• Lock the caster [B]
• Fix the caster lock stays [C] and tighten the screws [D]
• Attach the stabilizing brackets [E] (these help to prevent the machine from
falling over).
1-6
INSTALLATION PROCEDURE
Installation
28 March 2006
C267I103.WMF
C267I111.WMF
C267I106.WMF
1-7
INSTALLATION PROCEDURE
28 March 2006
3. Remove the filament tape as shown above.
C267I109.WMF
C267I151.WMF
4. Remove the string securing the covers and units as shown above.
1-8
INSTALLATION PROCEDURE
[A]
C267I110.WMF
5. Open the paper table.
6. Pull out the master making unit, and take out the accessory bag [A].
7. Remove the filament tape and string securing the covers and units.
C267I907.WMF
8. Insert both spools into a new master roll.
C267I152.WMF
9. Install the master roll, and open the master making unit cover,
1-9
Installation
28 March 2006
INSTALLATION PROCEDURE
28 March 2006
[B]
[B]
C267I153.WMF
10. Insert the leading edge of the master roll under the platen roller. The arrows [B]
indicate the correct position of the master leading edge.
[C]
[D]
C267I154.WMF
11. Close the master making unit cover [C] using both hands until it clicks into
place.
12. Close the master making unit [D].
1-10
INSTALLATION PROCEDURE
Installation
28 March 2006
[E]
[F]
C267I107.WMF
13. Open the front door.
14. Release the ink holder lock lever [E] and pull out the ink holder [F].
15. Remove the cap of the new ink cartridge, and insert a new ink cartridge into the
ink holder.
16. Set the ink holder [F].
[I]
[G]
[I]
[H]
[H]
C267I155.WMF
17. Load a stack of paper on the paper table.
18. Shift the lock lever [G] in the direction of the arrow. Make sure that the side
plates [H] touch the paper gently.
19. Shift the lock lever [G] to its original position.
NOTE: Two side fence friction pads [I] are included as accessories. They are not
used normally, but if paper multi-feed frequently occurs or thin paper is
used, the side fence friction pads [I] can be installed to apply stopping
pressure to the paper.
1-11
INSTALLATION PROCEDURE
28 March 2006
[J]
[J]
C267I105.WMF
20. Raise the paper delivery table slightly, then gently lower it.
21. Lift the side plates and the end plate, and attach the side plate guides [J] for
both side plates.
NOTE: When printing on A4 SEF, 81/2" SEF, B5 JIS LEF and SEF size paper and
thin paper, you should attach the side plate guides to the side plates of the
paper delivery tray. Users can also attach these guides.
22. Adjust the side and end fences of the paper delivery table to match the paper
size.
23. Firmly insert the power plug in the outlet.
24. Turn on the main switch.
25. Make a master and make 30 prints with this master. Do this at least three times,
until the image quality is acceptable.
NOTE: This is a new drum. Because of this, before the first print is made, ink is
supplied automatically. This takes 2 minutes.
1-12
INSTALLATION PROCEDURE
Changing the operation panel language
There are ten languages in the machine. If you need to change the language, use
the User Tools menu to set the language.
• On the operation panel, press the User Tools key.
• Select “2. System”.
• Select “5. Language on LCD”.
• Select the language.
Date/Time Setting
Use the User Tools menu to set the current date and time.
• On the operation panel, press the User Tools key.
• Select “2. System”.
• Select “6. Date/Time”.
• Enter the date and the time.
SP Codes Setting
SP No.
SP3-2
Menu
Input TEL number
Function
Do this SP and input the contact numbers of the customer
engineer. These numbers are shown when a service call is
issued.
1-13
Installation
28 March 2006
INSTALLATION PROCEDURE
28 March 2006
1.2.2 COLOR DRUM (OPTION)
Accessory Check
Check the quantity and condition of the accessories in the box against this list:
Description
Quantity
1. Color Indicator Decal ...........................................................5
Installation Procedure
CAUTION
To avoid serious injury, do not connect the power plug to the machine until
you are instructed to do so.
[A]
C267I900.WMF
1. Remove the protective sheets [A] from the drum.
2. Attach a color indicator decal to the drum case. The decal must be the same
color as the ink in use.
3. Remove the drum from the machine.
4. Leave the master wrapped around the removed drum to protect the drum from
dust and from drying.
5. Keep the removed drum in the drum case.
6. Install the color drum in the machine.
NOTE: The color drum indicator on the operation panel stays lit when a drum
is mounted in the machine.
7. Remove the ink cartridge cap.
8. Insert the ink cartridge in the ink holder.
9. After main body installation, firmly insert the power plug in the outlet.
10. Turn on the main switch.
11. Make a master and make 30 prints with this master. Do this at least three times,
until the image quality is acceptable.
NOTE: This is a new drum. Because of this, before the first print is made, ink is
supplied automatically. This takes 2 minutes.
1-14
28 March 2006
INSTALLATION PROCEDURE
Accessory Check
2
1
7
3
4
5
6
C267I908.WMF
Check the quantity and condition of the accessories in the box against this list:
Description
Quantity
1. Stepped Screw.................................................................2
2. Screws .............................................................................2
3. Screwdriver Tool ..............................................................1
4. DF Exposure Glass ..........................................................1
5. Decal - Scale – mm..........................................................1
6. Decal - Scale – inch .........................................................1
7. Scale Guide......................................................................1
8. Attention Label .................................................................1
1-15
Installation
1.2.3 ADF (OPTION)
INSTALLATION PROCEDURE
28 March 2006
Installation Procedure
CAUTION
To avoid serious injury, do not connect the power plug to the machine until
you are instructed to do so.
C267I909.WMF
1. Remove the strips of tape.
[C]
[D]
[E]
[B]
[A]
[F]
C267I202.WMF
2. Remove the left scale [A] ( x 2).
3. Place the DF exposure glass [B] on the glass holder.
NOTE: When installing the DF exposure glass, make sure that the white dot [C] is
positioned at the front side, as shown.
4. Peel off the backing [D] of the double-sided tape attached to the rear side of the
scale guide [E], then install the scale guide (2 screws removed in step 2).
5. Install the two stepped screws [F].
1-16
INSTALLATION PROCEDURE
Installation
28 March 2006
[H]
[H]
[G]
[G]
[I]
C267I203.WMF
6. Mount the DF by aligning the holes [G] in the DF with the stepped screws, then
slide the DF to the front as shown.
7. Secure the DF unit with two screws [H].
8. Connect the cables [I] to the main body.
[J]
C267I910.WMF
9. Attach the scale decal [J] as shown.
10. Connect the power cord, then turn the main switch on.
1-17
INSTALLATION PROCEDURE
28 March 2006
1.2.4 PLATEN COVER (OPTION)
Accessory Check
Check the quantity and condition of the accessories in the box against this list:
Description
Quantity
1. Stepped Screw ....................................................................2
Installation Procedure
CAUTION
To avoid serious injury, do not connect the power plug to the machine until
you are instructed to do so.
[A]
[A]
C267I201.WMF
1. Install the platen cover [A] ( x 2).
1-18
28 March 2006
INSTALLATION PROCEDURE
Accessory Check
Check the quantity and condition of the accessories in the box against this list:
Description
Quantity
1. Knob Screw (For C210, C217, C218, C219, C222, C223,
C225, C228, C238, C237, C238, C248, C249, C264
and C267) ............................................................................2
2. Screw M4 x 25 (For C211, C212, C213, C214, C216,
C224 and C226)...................................................................2
3. Hexagon Nut M4 (For C211, C212, C213, C214, C216,
C224 and C226)...................................................................2
4. Auxiliary Bracket (For C226 and C267) ...............................1
5. Auxiliary Bracket (For C238, C247 and C249).....................1
6. Auxiliary Bracket (For C264)................................................1
7. Screw M4 x 8 (For C226, C238, C247, C249 and C267......4
8. Lock Washer (For C226 only)..............................................1
9. Lock Washer (Without C267) ..............................................1
10. Tape ..................................................................................1
Installation Procedure
[A]
C267I903.WMF
1. Turn off the main switch and unplug the power cord.
2. Remove the paper delivery cover ( x 5).
3. Remove the cutout [A] from the rear cover, as shown.
1-19
Installation
1.2.5 TAPE DISPENSER (OPTION)
INSTALLATION PROCEDURE
28 March 2006
[B]
[D]
[C]
C267I901.WMF
4. Connect the harness from the tape dispenser to the connector [B].
5. Remove the screw [C] that is beside the connector [B]. Reuse the screw to
secure the bracket [D], as shown.
[G]
[E]
[F]
[F]
C267I902.WMF
6. Open the master eject unit.
7. Install the auxiliary bracket [E] on the tape dispenser with M4x8 screws
(accessories) [F].
8. Install the tape dispenser on the main body with two M4x8 screws [G]
(accessories) in the two outer holes in the tape dispenser bracket.
9. Close the master eject unit. Reinstall the paper delivery cover.
1-20
INSTALLATION PROCEDURE
[H]
[I]
C238I519.PCX
10. Open the tape dispenser cover [H]. Then, insert the leading edge of the tape
into the tape entrance until it stops as shown in the illustration [I].
NOTE: Be sure that the tape is installed in the proper direction. If it is not, the tape
dispenser will not work correctly.
[J]
C238I520.PCX
11. Firmly insert the power plug in the outlet.
12. Turn on the main switch of the main body.
13. Turn on the tape dispenser switch [J].
1-21
Installation
28 March 2006
INSTALLATION PROCEDURE
28 March 2006
[K]
C238I521.PCX
14. Press the tape cut button [K] to cut off the leading edge of the tape.
15. Check the tape dispenser operation using the Memory/Class modes of the
main body.
1-22
28 March 2006
INSTALLATION PROCEDURE
Installation
1.2.6 PRINTER UNIT VC-20 (OPTION)
Accessory Check
Make sure that you have all the accessories listed below.
1
2
3
C267I906.WMF
Description
Quantity
1. VC-20 Interface Board.........................................................1
2. Screws.................................................................................3
3. Installation CD .....................................................................1
4. Quick Install Guide ..............................................................1
5. Safety Information ...............................................................1
1-23
INSTALLATION PROCEDURE
28 March 2006
Installation Procedure
CAUTION
To avoid serious injury, do not connect the power plug to the machine until
you are instructed to do so.
[A]
[B]
C267I101.WMF
1. Remove the small rear cover [A] in the rear cover. ( x 2)
2. Cut out the USB port cover [B] in the small rear cover.
[C]
C267I101A.WMF
3. Connect the VC-20 interface board [C] to CN114 of the MPU board and secure
it using three screws.
4. Reinstall the small rear cover.
1-24
28 March 2006
PREVENTIVE MAINTENANCE
2. PREVENTIVE MAINTENANCE
Symbol Key: C: Clean
R: Replace
L: Lubricate
WARNING
Turn off the main power switch and unplug the machine before performing any
procedure in this section.
Interval
Item
Optics
6M
Time
1Y 2Y
Print Counter
5Y 300K 600K 1.2M 3M
EM
Exposure glass
C
C
C
C
C
Platen cover
C
C
C
C
C
White plate
C
C
C
C
C
C
C
C
C
C
Note
Clean with
water.
Clean with
water.
Clean with
water.
Master Feed
Thermal head
Platen roller
C
Drum and Ink Supply
Ink nozzle
Drum master sensor
Black patches
C
Cloth screen
Ink roller one-way
clutch
Drum master sensor
Master clapper
C
C
C
C
C
C
Clean with
alcohol.
Clean with
alcohol.
Damp cloth
Dry cloth
Dry cloth
R
R
C
C
C
C
C
C
Paper feed roller
C
C
C
C
R
C
Pick-up roller
C
C
C
C
R
C
Friction pad
C
C
C
C
R
C
Dry cloth
Clean with
water.
Paper Feed
Registration rollers
C
Feed start timing
sensor
Registration sensor
C
C
C
C
C
C
2-1
C
Dry or damp
cloth
Dry or damp
cloth
Clean with
alcohol.
Clean with
alcohol.
Dry cloth
Dry cloth
Preventive
Maintenance
The following items should be maintained periodically. There are two sets of
intervals - one based on time and the other based on print count or original count.
For maintenance items with entries in both of them, use whichever comes first.
PREVENTIVE MAINTENANCE
Interval
Item
Exit sensor
6M
Press roller
C
28 March 2006
Time
1Y 2Y
C
C
Print Counter
5Y 300K 600K 1.2M 3M
C
C
R
Paper delivery unit
bushings
C
L
Drum drive gears
L
Paper feed clutch
Paper delivery belts
EM
C
R
Note
Dry cloth
Dry or damp
cloth
Motor oil
(SAE #20)
Grease
(Alvania #2)
R
R
ADF
Interval
Item
Feed belt
Separation roller
Pick-up roller
White plate
DF exposure glass
Platen cover
Time
6M
C
C
C
C
C
C
1Y
C
C
C
C
C
C
2Y
C
C
C
C
C
C
Original
Counter
5Y
C
C
C
C
C
C
EM
Note
C
C
C
C
C
C
Clean with water or alcohol.
Clean with water or alcohol.
Clean with water or alcohol.
Clean with water or alcohol.
Clean with water.
Clean with water or alcohol.
80K
R
R
R
2-2
28 March 2006
GENERAL CAUTION
3. REPLACEMENT AND ADJUSTMENT
3.1 GENERAL CAUTION
CAUTION
Turn off the main power switch and unplug the machine before attempting
any of the procedures in this section.
3.2 COVERS
Replacement
Adjustment
3.2.1 FRONT COVER / FRONT DOOR
[A]
C267R001.WMF
[B]
C267R083.WMF
[A]: Front cover ( x 9)
[B]: Front door ( x 4)
3-1
COVERS
28 March 2006
3.2.2 OPERATION PANEL
[A]
45°
45°
45° 45°
C267R002.WMF
Front cover (☛ 3.2.1)
[A]: Operation panel ( x 5, x 2, = x 3)
3.2.3 REAR COVER
[A]
[A]: Rear cover ( x 9)
3-2
C267R003.WMF
28 March 2006
COVERS
3.2.4 UPPER COVERS
[A]
[B]
C267R004.WMF
[A]: Left upper cover ( x 2)
[B]: Top rear cover ( x 1)
[C]: Right upper cover ( x 1)
3-3
Replacement
Adjustment
[C]
BOARDS
28 March 2006
3.3 BOARDS
3.3.1 MPU
[A]
[B]
C267R007.WMF
• Rear cover (☛ 3.2.3)
[A]: MPU ( x 10, x 18, 2 ribbon cables)
NOTE: 1) Take the NVRAM [B] from the old board and put it in the socket on the
new board.
2) Adjust the master end sensor (☛ 3.5.4) after installing the new MPU.
3) Adjust the ink detection (☛ 3.9.6) after installing the new MPU.
4) If you must replace the MPU RAM, you must then do the image
adjustments after you install the new RAM (see section 5.7.7. for the
procedure).
3-4
28 March 2006
BOARDS
3.3.2 PSU
NOTE: When the PSU is replaced, the thermal head voltage returns to the default.
Adjust the thermal head voltage (☛ 3.5.7) after installing the new board.
Replacement
Adjustment
[A]
[B]
C267R005.WMF
PSU board
• Rear cover (☛ 3.2.3)
[A]: PSU ( x 6, x 7)
NOTE: The split washer screw [B] is used for grounding. Do not use another type
of screw here.
PSU board with bracket
• Rear cover (☛ 3.2.3)
[A]: PSU ( x 5, x 7)
3-5
SCANNER
28 March 2006
3.4 SCANNER
3.4.1 EXPOSURE GLASS/DF EXPOSURE GLASS, SCALES
[E]
[A]
[B]
[D]
[F]
[C]
C267R008.WMF
Exposure Glass
[A]: Left scale ( x 2)
[B]: Rear scale ( x 3)
[C]: Exposure glass
NOTE: When reinstalling, make sure that the mark [E] is at the rear left corner, and
that the left edge is aligned with the support on the frame.
DF Exposure Glass
[A]: Left scale ( x 2)
[D]: DF exposure glass
NOTE: When reinstalling, make sure that the mark [F] is on the bottom.
3-6
28 March 2006
SCANNER
3.4.2 LENS BLOCK
CAUTION: 1) Do not touch the paint-locked screws on the lens block. The position
of the lens assembly (black part) is adjusted before shipment.
2) Do not grasp the PCB or the lens assembly when handling the lens
block. The lens assembly may slide out of position.
[A]
[B]
C267R009.WMF
• Exposure glass (☛ 3.4.1)
[A]: Lens cover ( x 5)
[B]: Ribbon cable
[C]: Lens block ( x 4).
3-7
Replacement
Adjustment
[C]
SCANNER
28 March 2006
3.4.3 EXPOSURE LAMP, LAMP STABILIZER BOARD
[D]
[C]
[B]
[A]
C267R902.WMF
• Exposure glass (☛ 3.4.1)
1. Slide the first scanner to a position where the front end of the lamp is visible.
2. Place one hand under the lamp stabilizer board [A] and release the hook [B].
3. Remove the lamp stabilizer board [A] ( x 2).
4. Press the plastic latch [C] and push the front end of the lamp toward the rear.
5. Remove the lamp [D] (with the cable).
3-8
28 March 2006
SCANNER
[A]
C267R010.WMF
• Rear cover (☛ 3.2.3)
• Exposure glass (☛ 3.4.1)
[A]: Scanner motor ( x 3, x 1, = x 1, 1 spring, 1 belt)
NOTE: When reassembling, install the belt first, and set the spring next. Fasten
the leftmost screw (viewed from the rear), then fasten the other two screws.
3.4.5 SCANNER HOME POSITION SENSOR
[B]
[A]
[C]
C267R078.WMF
• Left upper cover (☛ 3.2.4)
• Top rear cover (☛ 3.2.4)
• Front cover (☛ 3.2.1)
• Operation panel (☛ 3.2.2)
• Exposure glass, DF exposure glass (if installed) (☛ 3.4.1)
[A]: Scanner left lid ( x 7, x 1).
[B]: Sensor tape
[C]: Scanner home position sensor
3-9
Replacement
Adjustment
3.4.4 SCANNER MOTOR
SCANNER
28 March 2006
3.4.6 PLATEN COVER SENSOR
[A]
C267R082.WMF
• Top rear cover (☛ 3.2.4)
[A]: Platen cover sensor ( x 1).
3-10
28 March 2006
SCANNER
3.4.7 ADJUSTING THE SCANNER POSITION
CAUTION
Grasp the front and rear ends (not the middle) of the first scanner when
you manually move it. The first scanner may be damaged if you press,
push, or pull the middle part of the scanner.
Overview
[A]
Replacement
Adjustment
[B]
[C]
C267R903.WMF
Adjust the scanner positions at these times:
• When the first scanner [C] and second scanner [B] are not parallel with the side
frames [A]
• When you have replaced one or more of the scanner belts.
To adjust the scanner positions, do either of the following:
• To adjust the belt contact points on the first scanner (☛ Adjusting the Belt
Contact Points for the First Scanner)
• To adjust the belt contact points on the scanner bracket (☛ Adjusting the Belt
Contact Points for the Second Scanner)
[D]
[D]
[E]
[E]
[F]
[F]
[G]
[G]
C267R087.WMF
3-11
SCANNER
28 March 2006
The two actions above have the same objectives: to align the following holes.
1st scanner [D], frame [E], arm of second scanner [F], and frame [G]
The scanner positions are correct when these holes are all aligned.
Adjusting the Belt Contact Points for the First Scanner
[C]
[A]
[B]
[D]
[E]
[F]
[H]
•
•
•
•
•
•
•
[G]
C267R905.WMF
ADF or platen cover
Front cover (☛ 3.2.1)
Operation panel (☛ 3.2.2)
Rear cover (☛ 3.2.3)
Top rear cover (☛ 3.2.4)
Left upper cover (☛ 3.2.4)
Exposure glass (☛ 3.4.1)
1. Loosen the 2 screws [A] [F].
2. Slide the 1st and 2nd scanners to align the following holes and marks (☛
Overview):
• Align all four holes: 1st scanner, frame, arm of second scanner and frame
3. Insert the positioning tools [D] [E] through the holes.
4. Check that the scanner belts [B] [C] [G] [H] are properly set between the
bracket and the 1st scanner.
5. Tighten the screws [A] [F].
6. Remove the positioning tools.
7. Reassemble the machine and check the operation.
3-12
28 March 2006
SCANNER
Adjusting the Belt Contact Points for the Second Scanner
[B]
[A]
C267R081.WMF
•
•
•
•
•
•
•
ADF or platen cover
Front cover (☛ 3.2.1)
Operation panel (☛ 3.2.2)
Rear cover (☛ 3.2.3)
Top rear cover (☛ 3.2.4)
Left upper cover (☛ 3.2.4)
Exposure glass (☛ 3.4.1)
1. Disconnect the platen cover sensor connector [A].
2. Scale bracket [B] ( x 2)
NOTE: 1) Take off the scale bracket, otherwise the screws [D] cannot be
loosened.
2) Take off the bracket [C] in order to take off the scale bracket.
3-13
Replacement
Adjustment
[C]
SCANNER
28 March 2006
[D]
[F]
[D]
[E]
C267R906.WMF
3. Loosen the 2 screws [D].
4. Slide the 2nd scanner to align the following holes and marks (☛ Overview):
• Align all four holes: 1st scanner, frame, arm of second scanner and frame
5. Insert the positioning tools [E] [F] through the holes.
6. Check that the scanner belts are properly set in the brackets.
7. Remove the positioning tools.
8. Reassemble the machine and check the operation.
3-14
28 March 2006
MASTER FEED
3.5 MASTER FEED
3.5.1 MASTER MAKING UNIT
[B]
C267R016.WMF
[A]: Master making unit cover ( x 3)
[B]: Master making unit ( x 2, x 4, = x 1, x 1))
3.5.2 MASTER MAKING UNIT SET SWITCHES
[A]
C267R036.WMF
Master making unit (☛ 3.5.1)
[A]: Master making unit set switch ( x 1, x 1)
3-15
Replacement
Adjustment
[A]
MASTER FEED
28 March 2006
[B]
C267R040.WMF
Front cover (☛ 3.2.1)
[B]: Master making unit set switch ( x 1, x 1)
NOTE: There are two master making unit set switches for safety. Both sensors
must be on or the machine will not start.
3-16
28 March 2006
MASTER FEED
3.5.3 THERMAL HEAD
[B]
[C]
Replacement
Adjustment
[A]
C267R054.WMF
• Master making unit (☛ 3.5.1)
[A]: Open the platen roller unit.
[B]: Thermal head upper cover ( x 2)
[C]: Thermal head side cover ( x 1)
[D]
C267R055.WMF
• Close the platen roller unit.
[D]: Thermal head ( x 2)
3-17
MASTER FEED
28 March 2006
Installation
[C]
[D]
[B]
[C]
[A]
C267R056.WMF
If the following remarks are not followed, the thermal head will be installed
incorrectly.
1. Fit the base’s springs [A] over the protrusions [B] on the underside of the
thermal head (5 points).
2. While fitting the tops of the springs [A] over the protrusions on the underside of
the thermal head, hook the lock pawls [C] of the thermal head onto the base (3
lock pawls). Make sure to set the front side [D] (the paper table side) first.
3. Make sure that all protrusions are properly fitted into the springs.
NOTE: 1) Adjust the thermal head voltage (☛3.5.7) after installing the new
thermal head.
2) Don’t touch the surface with bare hands. (If you touch it, clean the
surface with alcohol.)
3) Don’t touch the terminals of the connectors with bare hands.
3-18
28 March 2006
MASTER FEED
[A]
C267R057.WMF
Master making unit (☛ 3.5.1)
[A]: Master set cover sensor ( x 3, x 1)
3.5.5 MASTER END SENSOR
[A]
C267R058.WMF
Master making unit (☛ 3.5.1)
Thermal head upper cover (☛ 3.5.3)
Thermal head side cover (☛ 3.5.3)
[A]: Master end sensor ( x 2, x 1)
NOTE: Adjust the master end sensor (☛ 3.5.8) after installing a new sensor.
3-19
Replacement
Adjustment
3.5.4 MASTER SET COVER SENSOR
MASTER FEED
28 March 2006
3.5.6 CUTTER UNIT
[B]
[A]
[C]
C267R059.WMF
[D]
[E]
C267R060.WMF
Master making unit (☛ 3.5.1)
[A]: Bracket ( x 2)
[B]: Shaft ( x 2)
[C]: Bracket ( x 2)
[D]: Cutter unit (= x 3, x 1, x 1)
NOTE: To remove the screw [E], you must slide the thermal head a small
distance towards the paper feed table.
3-20
28 March 2006
MASTER FEED
3.5.7 THERMAL HEAD VOLTAGE ADJUSTMENT
CAUTION
This adjustment is always required when the thermal head or PSU has been
replaced.
Tools: Circuit tester
• Rear cover (☛ 3.2.3)
• Read the voltage value on the decal on the thermal head.
C267R013.WMF
1. Connect the positive terminal of a circuit tester to TP1 and the negative
terminal to TP2 on the PSU.
CAUTION: If the output and ground terminals touch each other, the board will
be damaged.
2. Connect the power plug, and turn on the main switch to access SP mode.
3. Select SP5-12 (Thermal head signal output).
4. Press the # key. Power is continuously supplied to the thermal head, which
could damage the thermal head, so press the clear/stop key if you cannot finish
the adjustment quickly.
A beeper sounds while the power is being supplied.
5. Measure the voltage, and turn RV1 on the PSU until the value is between “+0”
and “-0.1” volts from the value on the thermal head decal.
3-21
Replacement
Adjustment
Purpose: To maintain master making quality and extend the lifetime of the thermal
head.
Standard: Refer to the voltage value (X) printed on the thermal head. The value
varies from one thermal head to another.
The adjustment voltage should be between X and X - 0.1 V.
MASTER FEED
28 March 2006
3.5.8 MASTER END SENSOR ADJUSTMENT
Purpose: To ensure that the sensor detects the end mark (a solid black area) on
the master roll.
Standard: 2.0 ± 0.1 volts
Tools: The core of a used master roll (the core just before a master end display
appears)
C267R900.WMF
• Rear cover (☛ 3.2.3)
1. Place the core inside the master making unit, and close the master making unit.
2. Connect the power plug, and turn on the main switch.
3. Access SP6-50.
[A]
C267R015.WMF
4. Turn VR2 [A] on the MPU board until the display is 2.0 ± 0.1 volts.
3-22
28 March 2006
MASTER EJECT
3.6 MASTER EJECT
Replacement
Adjustment
3.6.1 MASTER EJECT UNIT
C267R017.WMF
Open the master eject unit.
[A]
C267R018.WMF
[A]: Master eject unit ( x 3, x 1)
3-23
MASTER EJECT
28 March 2006
3.6.2 MASTER EJECT ROLLERS
[C]
[B]
[A]
C267R062.WMF
• Master eject unit (☛ 3.6.1)
[A]: Gears ( x 1)
[B]: Lower master eject roller ( x 2)
[C]: Upper master eject roller ( x 2, 2 springs)
3.6.3 MASTER EJECT MOTOR / PRESSURE PLATE MOTOR
[C]
[A]
[B]
Master eject unit (☛ 3.6.1)
[A]: Gears ( x 1)
[B]: Master eject motor (= x 2, x 1, x 2)
[C]: Pressure plate motor (= x 2, x 1, x 2)
3-24
C267R063.WMF
28 March 2006
MASTER EJECT
3.6.4 DRUM MASTER SENSOR / MASTER EJECT SENSOR /
EJECT BOX SET SENSOR
[C]
[B]
[A]
Master eject unit (☛ 3.6.1)
Master eject box
[A]: Drum master sensor ( x 2, x 1)
[B]: Bracket ( x 2, = x 1)
[C]: Master eject sensor (= x 1, x 1)
[D]: Eject box set sensor ( x 1)
3-25
C267R064.WMF
Replacement
Adjustment
[D]
MASTER EJECT
28 March 2006
3.6.5 PRESSURE PLATE HP SENSOR / PRESSURE PLATE LIMIT
SENSOR
[C]
[A]
[B]
C267R065.WMF
Master eject unit (☛ 3.6.1)
Master eject box
[A]: Pressure plate HP sensor ( x 1)
[B]: Gear ( x 1, 1 pin)
[C]: Pressure plate limit sensor ( x 1)
3.6.6 AIR KNIFE FAN MOTOR
[B]
[A]
C267R066.WMF
[A]: Air knife fan duct ( x 2)
[B]: Air knife fan motor (= x 1, x 1, x 2)
3-26
28 March 2006
MASTER EJECT
3.6.7 MASTER EJECT POSITION SENSOR
Replacement
Adjustment
[A]
C267R035.WMF
• Rear cover (☛ 3.2.3)
[A]: Master eject position sensor (= x 1, x 1, x 1)
3.6.8 MASTER CLAMPER OPENING UNIT
[A]
C267R023.WMF
• Rear cover (☛ 3.2.3)
[A]: Master clamper opening unit ( x 3, x 2)
3-27
PAPER FEED
28 March 2006
3.7 PAPER FEED
3.7.1 PICK-UP ROLLER / PAPER FEED ROLLER / FRICTION PAD
[C]
[D]
0 to 4 mm
0 to 4 mm
[E]
[B]
[A]
C267R019.WMF
Move the separation pressure slider [E] to position 1.
[A]: Pick-up roller ( x 1)
[B]: Paper guide ( x 1)
[C]: Paper feed roller ( x 1)
[D]: Friction pad
NOTE: Do not change the position and direction of the paper guide [B].
3-28
28 March 2006
PAPER FEED
[A]
C267R034.WMF
• Rear cover (☛ 3.2.3)
[A]: Paper table lower limit sensor ( x 1, x 1)
3-29
Replacement
Adjustment
3.7.2 PAPER TABLE LOWER LIMIT SENSOR
PAPER FEED
28 March 2006
3.7.3 PAPER HEIGHT SENSOR 1 / 2
[B]
[A]
C267R036.WMF
[C]
[D]
C267R037.WMF
• Master making unit (☛ 3.5.1)
[A]: Paper feed unit cover ( x 2)
[B]: Paper feed unit cover – small ( x 4, x 1)
[C]: Paper height sensor 1 ( x 1, x 1)
[D]: Paper height sensor 2 ( x 1, x 1)
3-30
28 March 2006
PAPER FEED
3.7.4 PAPER END SENSOR
C267R029.WMF
[B]
[C]
C267R038.WMF
Rear cover (☛ 3.2.3)
[A]: Paper table ( x 1, x 2)
[B]: Paper table bottom plate ( x 5, 3 washers)
[C]: Paper end sensor ( x 2, x 1)
3-31
Replacement
Adjustment
[A]
PAPER FEED
28 March 2006
3.7.5 PAPER TABLE MOTOR
C267R040.WMF
Front cover (☛ 3.2.1)
[A]: Paper table motor ( x 2, x 1)
3.7.6 PAPER FEED CLUTCH
[B]
[A]
C267R022.WMF
Rear cover (☛ 3.2.3)
MPU (☛ 3.3.1)
[A]: Paper feed clutch bracket ( x 2)
[B]: Paper feed clutch (= x 1, x 1)
3-32
[A]
28 March 2006
PAPER FEED
3.7.7 PAPER SEPARATION PRESSURE ADJUSTMENT
The position of the screw can be changed in order to change the amount of
pressure exerted by the friction pad.
This adjustment can be done:
• When feeding special paper, especially thick paper
• When the customer is experiencing feed problems.
Replacement
Adjustment
[A]
[B]
[B]
C267R020.WMF
• Move the separation pressure slider [A] to position 1.
Increase the paper separation pressure: Move up the screws [B]
Decrease the paper separation pressure: Move down the screws [B]
Default position: lowest position
The adjustment is automatically applied to all settings of the separation pressure
slider.
3-33
PRINTING
28 March 2006
3.8 PRINTING
3.8.1 PRESS ROLLER
[B]
[A]
C267R907.WMF
CAUTION
Take care to avoid possible injury. If the printing pressure release arms
disengage, the press roller will be pulled upwards suddenly.
• Remove the drum
[A]: Press roller ( x 1)
The bearings on the rear and front differ. During installation, ensure that the
bearing with the stopper [B] is positioned towards the rear of the machine.
3-34
28 March 2006
PRINTING
3.8.2 REGISTRATION SENSOR
Replacement
Adjustment
[A]
C267R041.WMF
[A]: Registration sensor ( x 2, x 1)
3.8.3 FEED START TIMING SENSOR
[A]
[A]: Feed start timing sensor ( x 1, x 1)
3-35
C267R042.WMF
PRINTING
28 March 2006
3.8.4 2ND FEED TIMING SENSOR
[A]
C267R043.WMF
Open the master eject unit
[A]: 2nd feed timing sensor ( x 1, x 1)
3-36
28 March 2006
PRINTING
0±0.5 mm
[A]
C267R021.WMF
[B]
Rear cover (☛ 3.2.3)
MPU (☛ 3.3.1)
[A]: Registration motor (spring, x3, belt, x 1)
NOTE: 1) The side of the motor with the harness [B] should face downward, as
shown in the diagram.
2) The flange of the gear should face towards the motor as shown in the
diagram.
3-37
Replacement
Adjustment
3.8.5 REGISTRATION MOTOR
PRINTING
28 March 2006
3.8.6 REGISTRATION ROLLER
[A]
C267R029.WMF
[B]
C267R030.WMF
Front cover (☛ 3.2.1)
Rear cover (☛ 3.2.3)
[A]: Paper table ( x 1, x 2)
[B]: Plate ( x 4)
MPU (☛ 3.3.1)
PSU (☛ 3.3.2)
Registration motor (☛ 3.8.5)
3-38
28 March 2006
PRINTING
0±0.5 mm
C267R028.WMF
[D]
[E]
C267R031.WMF
[C]: Gear
[D]: Bearing ( x 2)
[E]: Registration roller
NOTE: The flange of gear [C] should face towards the machine, as shown in the
diagram.
3-39
Replacement
Adjustment
[C]
PRINTING
28 March 2006
3.8.7 PRESS ROLLER RELEASE SOLENOIDS
[A]
C267R039.WMF
[A]
C267R026.WMF
Front cover (☛ 3.2.1)
Rear cover (☛ 3.2.3)
[A]: Press roller release solenoid ( x 2, x 1)
NOTE: Adjust the press roller release lever (☛ 3.8.8) after installing the new
solenoid.
3-40
28 March 2006
PRINTING
3.8.8 PRESS ROLLER RELEASE LEVER ADJUSTMENT
Purpose: To maintain the correct clearance between the press roller arms and
press roller lock levers. This ensures that the press roller is correctly
released and pressed against the drum when the press roller release
solenoid is energized.
Standard: 0.7 to 1.2 mm
Replacement
Adjustment
Tools: Thickness gauge
[A]
C267R044.WMF
[C]
[E]
[E]
[B]
[D]
C267R908.WMF
• Front cover (☛ 3.2.1)
• Rear cover (☛ 3.2.3)
3-41
PRINTING
28 March 2006
1. Turn the drum manually until the drum master clamper on the drum moves into
the lowest position. (This is when the high points of the cams on the drum
flanges meet with the cam followers on both ends of the press roller.)
• To find out the correct position of the drum for the adjustment, look at the
rear end of the drum shaft. The recess on the drum drive gear meets the hole
[A] in the bracket when the drum is in the correct position.
2. Using a thickness gauge, measure the clearance [B] between the press roller
arm [C] and the press roller lock lever [D] (rear side). It should be between 0.7
and 1.2 mm.
3. If it is not correct, adjust the position of the press roller lock lever after
loosening the two screws [E].
4. Repeat steps 2 and 3 for the front side.
3.8.9 PRINTING PRESSURE ADJUSTMENT
Purpose: To make better print results without decreasing the run length.
Standard: Within 10 ± 0.5 mm
[A]
[B]
C267R051.WMF
• Paper delivery unit (☛ 3.10.1)
1. Adjust the distance [A] to 10 ± 0.5 mm by turning the adjusting bolt [B].
2. Repeat the same procedure for the printing pressure spring at the nonoperation side.
3-42
28 March 2006
DRUM
3.9 DRUM
3.9.1 PREPARATION
Before attempting any of the procedures in this section, wipe off the ink around the
ink roller. To do this, set SP2-10 (ink detection) to off, and feed paper until ink ends.
Replacement
Adjustment
3.9.2 CLOTH SCREEN
[A]
C267R909.WMF
[B]
C267R073.WMF
• Remove the drum
1. Remove the drum upper bracket ( x 4).
2. Release the stopper [A], then rotate the drum until the master clamper faces
top.
3. Remove the cloth screen [B] ( x 4).
3-43
DRUM
28 March 2006
Installation
[A]
[B]
C267R068.WMF
Inside
Outside
C267R070.WMF
3-44
28 March 2006
DRUM
C267R067.WMF
• Do not scratch the cloth screen or metal screen.
• Properly insert the edge of the cloth screen [A] on the cloth screen under the
mylar [B] on the metal screen, as shown above.
Otherwise, ink will leak from the trailing edge of the master on the drum during a
long printing run.
• Make sure that the correct side of the screen is facing up. In addition, make sure
that the stays for securing the cloth screen are positioned correctly.
• When replacing the cloth screen, spread the screen around the metal screen
while pulling the stay [C]. Adjust the stay so that it is parallel to the master
clamper, then tighten the screws.
• Make sure that the cloth screen is not wrinkled while spreading it around the
drum.
3-45
Replacement
Adjustment
[C]
DRUM
28 March 2006
3.9.3 CLAMPER / METAL SCREEN
[B]
[C]
[A]
C267R069.WMF
[E]
[D]
C267R074.WMF
• Remove the drum
• Cloth screen (☛ 3.9.2)
[A]: Clamper lever (1 hexagon screw)
[B]: Clamper - open the clamping plate [C], then remove the clamper.
NOTE: 1) Do not allow ink to get on the inside of the clamping plate [C].
Otherwise, the master may slip off and the image position on the
prints will move toward the trailing edge of the prints during a
printing run.
2) Use a cloth dampened with water to clean the inside of the clamping
plate [C]. Never use alcohol or other solvents, or the clamping force
of the magnet will be weakened.
[D]: Tape (do not lose it)
[E]: Metal screen ( x 12)
3-46
28 March 2006
DRUM
Installation
[E]
[A]
Replacement
Adjustment
[A]
C267R071.WMF
[B]
[D]
[C]
C267R072.WMF
• Make sure that the correct end of the metal screen is overlapping. (The right side
overlaps, as viewed from the non-operation side, as shown above.)
• The 4 screws holding the drum master clamper are longer than the 12 screws
holding the metal screen, although they are similar in appearance. Be careful not
to mix them up or use the wrong screws.
• When installing the metal screen, secure the trailing edge first with the 2 screws.
Then, tighten the other screws while removing the slack from the screen. Make
sure that the gap between the drum flanges and the screen is 0.3 mm or less, as
shown above. (The two holes [A] on the trailing side are round holes and the
other holes are long holes, to allow for the removal of the slack.)
• Position the springs [B] and [C] (one each at the front and rear) as shown when
reinstalling the drum master clamper [D].
• Do not scratch the cloth screen or metal screen.
NOTE: The side [E] with the part number printed on it must be on the top.
3-47
DRUM
28 March 2006
3.9.4 INK PUMP UNIT
[A]
C267R075.WMF
• Remove the drum
• Cloth screen (☛ 3.9.2)
• Clamper / Metal screen (☛ 3.9.3)
[A]: Ink pump unit ( x 1, x 2)
3-48
28 March 2006
DRUM
3.9.5 INK ROLLER UNIT / INK ROLLER ONE-WAY CLUTCH
[D]
[C]
Replacement
Adjustment
[B]
[A]
C267R910.WMF
• Wipe off the ink around the ink roller beforehand (use SP2-10).
• Remove the drum
• Cloth screen (☛ 3.9.2)
• Clamper / Metal screen (☛ 3.9.3)
[A]: Connector cover ( x 2, x 2)
[B]: Ink socket ( x 1)
[C]: Front drum bracket ( x 3)
[D]: Front drum flange
[G]
[E]
[F]
C267R911.WMF
[E]: Drum rear plate ( x 2)
Untight the screw [F] to take off the drum rear stoppers ( x 1)
[G]: Drum rear flange
3-49
DRUM
28 March 2006
[H]
[I]
C267R901.WMF
[H]: Ink roller unit
[I]: Ink roller one-way clutch
3-50
28 March 2006
DRUM
3.9.6 DOCTOR ROLLER GAP ADJUSTMENT
Purpose: To control the ink thickness around the ink roller.
Standard: A 0.07mm gauge passes, but a 0.09mm gauge does not.
Tools: Thickness gauge
Normally the doctor roller gap is not adjusted or changed. It tends to be
difficult to change in the field. If the gap is too narrow, an uneven image
may appear on the prints. If it is too wide, too much ink will be applied to
the drum screens, resulting in ink leakage from the drum.
[B]
[A]
[C]
C267R076.WMF
• Wipe off the ink around the ink roller beforehand. (Use SP2-10)
• Remove the drum
• Remove the Ink roller unit
1. Make sure that a 0.07 mm gap gauge goes through the gap [A] between the ink
and doctor rollers, and that a 0.09 mm gap gauge does not.
NOTE: 1) The gap should be checked at both ends of the doctor roller. Insert a
gap gauge at each end of the roller. The gap tends to be larger for
the center.
2) While the gap gauge is inserted, hold the doctor and ink rollers with
your fingers in order to stop the rollers from rotating.
3) While the gap gauge is inserted, hold the end of the gap gauge.
2. If the gap is out of the standard, loosen the screw [B] and adjust the gap by
turning the cam bushing [C] for the front and for the rear.
NOTE: Make sure to repeat the adjustment for both ends of the rollers.
3-51
Replacement
Adjustment
CAUTION
DRUM
28 March 2006
3.9.7 INK DETECTION ADJUSTMENT
Using an Oscilloscope
Purpose: To ensure that the CPU detects a no ink condition.
Standard: 4.0 ± 0.2 µsec
NOTE: 1) Before attempting this procedure, wipe off the ink around the ink roller.
To do this, set SP2-10 (Ink Detection) to OFF, and feed paper until ink
ends.
2) This adjustment is required every time the MPU has been replaced.
3) Normally, the simple method is sufficient. But, the oscilloscope method
is more accurate. Use the oscilloscope method if you cannot adjust the
sensor to the required value with the simple method, or if ink flooding
problems occur after adjustment with the simple method.
CH1
(Standard signal)
4.0 ± 0.2 µsec
CH2
(Detection signal)
C267R912.WMF
1. Turn off the main switch and disconnect the power plug.
2. Remove the rear cover.
3. Connect the CH1 probe of an oscilloscope to TP25 (INK1), the CH2 probe to
TP23 (INK2). Select the 2-microsecond range on the oscilloscope.
4. Connect the power plug and turn on the main switch.
5. Make sure that the waveform is as shown in the illustration while the ink end
indicator lights.
6. If it is not correct, adjust the ON timing of the detection signal by turning VR1
beside the test pins.
NOTE: 1) If the ink detection off mode has been selected with SP2-10, do not
forget to return it to the default (detection on).
3-52
28 March 2006
DRUM
Simple Method
Purpose: To ensure that the CPU detects a no ink condition.
Standard: 4.0 ± 0.2 µsec
[A]
C267R015.WMF
• Rear cover (☛ 3.2.3)
1. Access SP6-40.
2. Turn VR1 [A] on the MPU board until the display is “4.0 ± 0.2 µsec”.
NOTE: When the drum has ink inside, the machine displays “----“. Do SP 2-10
again, then go back to step 1.
NOTE: If the simple method gives an inaccurate result (causing ink flooding, for
example) , it is possible that too much ink will come out into the drum
during printing. If this happens, repeat the adjustment, but use the
oscilloscope method, because this is more accurate.
3-53
Replacement
Adjustment
NOTE: 1) Before attempting this procedure, wipe off the ink around the ink roller.
To do this, set SP2-10 (Ink Detection) to OFF, and feed paper until ink
ends.
2) This adjustment is required every time the MPU has been replaced.
3) Normally, the simple method is sufficient. But, the oscilloscope method
is more accurate. Use the oscilloscope method if you cannot adjust the
sensor to the required value with the simple method, or if ink flooding
problems occur after adjustment with the simple method.
PAPER DELIVERY
28 March 2006
3.10 PAPER DELIVERY
3.10.1 PAPER DELIVERY UNIT
[A]
C267R046.WMF
[B]
C267R047.WMF
3-54
PAPER DELIVERY
[C]
C267R048.WMF
• Rear cover (☛ 3.2.3)
[A]: Paper table ( x 2)
[B]: Paper delivery cover ( x 5)
[C]: Paper delivery unit ( x 2, x 2, x 1)
3-55
Replacement
Adjustment
28 March 2006
PAPER DELIVERY
28 March 2006
3.10.2 DELIVERY BELT / PAPER EXIT SENSOR / VACUUM FAN
MOTOR / PAPER DELIVERY UNIT BUSHINGS
[B]
[A]
[C]
C267R049.WMF
[D]
[F]
[E]
[E]
[E]
[D]
C267R050.WMF
• Remove the paper delivery unit (☛ 3.10.1)
[A]: Vacuum fan motor bracket ( x 4)
[B]: Vacuum fan motor ( x 2)
[C]: Paper exit sensor ( x 1)
[D]: Delivery belts ( x 1)
[E]: Paper delivery unit bushings
NOTE: 1) Make sure that you install the vacuum fan [B] the correct way around.
2) Install the delivery belt [D] the correct way around. The writing must be
on the outside surface of the belt.
3) The flat part of the “D” shaped cutout in the shaft [F] must face upwards.
3-56
28 March 2006
PAPER DELIVERY
3.10.3 EXIT PAWL ADJUSTMENT
Purpose: To ensure that the exit pawls can move out of the way of the drum
master clamper while the drum is rotating.
Clearance adjustment
[D]
Replacement
Adjustment
Standard: Within 1.15 ± 0.15 mm
[B]
[A]
[C]
C267R913.WMF
[E]
[F]
C267R914.WMF
• Front cover (☛ 3.2.1)
• Rear cover (☛ 3.2.3)
1. Turn the drum to the drum home position.
3-57
PAPER DELIVERY
28 March 2006
NOTE: The drum turns to home position automatically immediately after the
power switch is turned on.
2. Loosen screw [A] then screw [B] in this order (do not remove them). Make sure
that the bracket [C] becomes free from engagement and the cam follower [D]
contacts the drum flange.
3. Using a gap gauge, measure the clearance [E] between the drum surface and
the exit pawls. It should be 1.15 ± 0.15 mm.
4. If the clearance is not correct, adjust the clearance by turning the bolt [F].
5. Reposition the bracket [C] and tighten the screws [A] and [B].
Timing adjustment
Do this after the clearance adjustment.
Standard: 0 or less than 0.5 mm
[A]
C267R044.WMF
3-58
28 March 2006
PAPER DELIVERY
[G]
[E]
[C]
[D]
C267R052.WMF
1. Turn the drum manually until the recess in the drum drive gear meets the
positioning hole [A] in the bracket, as shown.
2. Loosen screw [B] then screw [C] in that order (do not remove them). Make sure
that the bracket [D] becomes free from engagement and the cam follower [E]
contacts the drum flange.
3. Measure the gap [F] between the cam follower and cam face (front drum
flange). It should be 0 to 0.5 mm.
4. If the gap is not correct, loosen the two screws securing the cam follower
bracket [G].
5. Re-tighten the two screws while pushing the cam follower against the cam face.
Make sure that the gap [F] is 0 or less than 0.5 mm.
NOTE: Do not push the cam followers too strongly against the cam.
6. Re-position the bracket [D] and tighten the screws [B] and [C].
3-59
Replacement
Adjustment
[F]
[B]
MAIN DRIVE
28 March 2006
3.11 MAIN DRIVE
3.11.1 MAIN MOTOR
[A]
C267R029.WMF
[B]
C267R030.WMF
Rear cover (☛3.2.3)
MPU (☛3.3.1)
PSU (☛3.3.2)
[A]: Paper table ( x 1, x 2)
[B]: Plate ( x 4)
3-60
28 March 2006
MAIN DRIVE
[C]
[D]
C267R021.WMF
[C]: Registration motor (spring, x3, belt)
NOTE: 1) The side of the motor with the harness [D] should face downward, as
shown in the diagram.
2) The flange of the gear should face towards the motor, as shown in the
diagram.
[E]
C267R025.WMF
[E]: Gear ( x 1, x 4, = x 4)
3-61
Replacement
Adjustment
0±0.5 mm
MAIN DRIVE
28 March 2006
[F]
C267R027.WMF
Paper feed clutch (☛3.7.2)
[F]: Drive bracket ( x 8)
[G]
C267R032.WMF
[G]: Main motor (= x 1, x 4)
NOTE: Adjust the main drive timing belt (☛ 3.11.2) after installing the new main
motor.
3-62
28 March 2006
MAIN DRIVE
3.11.2 MAIN DRIVE TIMING BELT ADJUSTMENT
After the timing belt is replaced, correct belt tension must be applied.
[A]
[C]
[D]
[B]
Replacement
Adjustment
[E]
C267R053.WMF
• Rear cover (☛ 3.2.3)
• MPU (☛ 3.3.1)
1. Loosen the screws [A], [B], and [C].
2. Move the tension roller [D] to the right with a screwdriver [E] as shown.
3. Tighten the screws [A], [B], and [C].
4. Remove the screwdriver.
3-63
MAIN DRIVE
28 March 2006
3.11.3 MAIN MOTOR PULLEY POSITION
After putting the pulley back on the main motor shaft, refer to the above illustration
for the correct position of the pulley.
Standard: 46.3 ±0.3 mm
46.3±0.3 mm
[A]
C267R033.WMF
NOTE: Tight the screws alternately little by little. Do not tighten them completely
one by one.
3-64
28 March 2006
FIRMWARE UPDATE (I/O ROM)
3.12 FIRMWARE UPDATE (I/O ROM)
Replacement
Adjustment
The I/O control firmware in the EPROM on the MPU can be updated by replacing
the EPROM.
[A]
C267R045.WMF
1. Before upgrading the I/O ROM firmware, check the current ROM version with
SP1-74.
2. Turn off the main switch and disconnect the power plug.
3. Remove the rear cover.
4. Replace the EPROM [A] on the MPU.
5. Connect the power plug and turn on the main switch.
6. Access SP1-74 and confirm that the ROM version was changed.
NOTE: If you upgrade the main firmware, refer to section 5.9.2.
3.13 SPECIAL TOOLS
The following are the special tools used for service.
Description
Scanner positioning pins (4 pins as a set)
Flash memory card – 4MB
Part number
A0069104
N8036701
3-65
Note
☛ 3.4.7
☛ 5.9
COLOR DRUM
28 March 2006
3.14 COLOR DRUM
3.14.1 INK PUMP ADJUSTMENT
Purpose: To ensure the smooth operation of the ink pump plunger by properly
positioning its holder.
[A]
[D]
[B]
[C]
C267R915.WMF
• Remove the drum
• Cloth screen (☛ 3.9.2)
• Clamper / Metal screen (☛ 3.9.3)
1. Remove the E-ring [A] to free the plunger from the pump drive slider [B].
2. Loose the two screws securing the holder [C]. (Do not remove the holder.)
3. Push the plunger [D] until it reaches the bottom.
NOTE: The end of the plunger [D] should not project outside from the holder [C].
3-66
COLOR DRUM
[E]
C267R916.WMF
4. Check that the piston motion is smooth.
5. If the motion is stiff, loosen the pump screws [E] and adjust the pump position.
6. After tightening, repeat step 4 and step 5.
[F]
[G]
[F]
C267R917.WMF
7. Re-tighten the two screws [F].
8. Check that the piston motion is smooth.
9. Reinstall the E-ring [G].
3-67
Replacement
Adjustment
28 March 2006
28 March 2006
SERVICE CALL CODES
4. TROUBLESHOOTING
4.1 SERVICE CALL CODES
No.
E-00
Description/Definition
Clamper Motor Failure
The MPU cannot detect the clamper
position sensor signal (open or closed)
within 3.0 seconds after the clamper motor
turns on.
E-01
Cutter error
The cutter HP sensor does not turn on
within 3.0 seconds after the cutter motor
turns on.
Paper Table Drive error
The paper height sensor or the table lower
limit sensor does not turn on within 7.5
seconds after the table motor turns on.
Paper height sensor 1 or 2 does not turn on
within 1 second after the paper height
sensor 1 or 2 turn on.
Thermal Head Overheat
Temperature of the thermal head is greater
than 65°C when the Start key is pressed.
Main Motor Lock
The CPU cannot detect the master eject
position sensor (drum HP) signal within 5.0
seconds after the main motor turns on.
E-02
E-04
E-06
E-09
E-10
Points to Check
Clamper drive
Clamper sensors
Clamper motor
MPU board
Main motor encoder
Master eject position sensor
Cutter drive
Cutter switch
Cutter motor
Paper table drive
Paper table motor
Paper height sensor 1 or 2
Paper table lower limit sensor
Gears
Paper table spring
Overheat (wait for the thermal head
to cool down)
Thermal head
Main motor drive
Main motor
Motor drive board
Master eject position sensor
Thermal head thermistor
Thermal head connector
Thermal Head Thermistor Open
The thermistor output voltage is over 4.432
volts.
Thermal head connector
Thermal Head Energy Pulse error
Thermal head
The CPU detects an abnormal ID signal
from the thermal head energy control pulse. MPU
4-1
TroubleService
Tables
shooting
NOTE: 1) If the problem concerns electrical circuit boards, first disconnect then
reconnect the connectors before replacing the PCBs.
2) If the problem concerns a motor lock, first check the mechanical load
before replacing motors or sensors.
SERVICE CALL CODES
No.
E-12
E-13
E-22
E-23
E-24
E-40
28 March 2006
Description/Definition
Pressure Plate error
The pressure plate home position sensor
does not turn on within 6 seconds during
initialization.
Both the pressure plate home position and
pressure plate limit sensors turn on when
the main SW is turned on.
The pressure plate home position sensor
does not turn off when the pressure plate
limit sensor does not turn on within 4.5
seconds when compressing the ejected
master.
Scanner error
The scanner HP sensor does not turn on
after the scanner motor has moved for more
than 10 seconds back to home position after
scanning.
The scanner cannot leave the home position
within 2.0 seconds of power on.
Just after switching the power on, the
scanner cannot return to the home position
within 2.0 seconds of leaving.
2nd Feed Start Timing Sensor error
The 2nd feed start timing sensor does not
activate before the master eject position
sensor activates.
Master Eject Position Sensor (Drum HP)
error
The master eject position sensor does not
activate before the feed start timing sensor
activates.
Feed Start Timing Sensor error
The feed start timing sensor does not
activate before the 2nd feed timing sensor
activates.
Thermal Head ID error
The CPU detects an abnormal ID signal
from the thermal head.
Points to Check
Pressure plate drive
Pressure plate motor
Plate position sensors
Master eject error
Scanner drive
Scanner HP sensor
Scanner motor
Scanner wire has come off
Drum sensors
Feeler
Drum sensors
Feeler
Drum sensors
Feeler
Different thermal head
MPU
Thermal head connector
disconnected
E-44
MSU error
Replace the MPU
E-50
NVRAM data version disagreement
Data for the uploading NVRAM is not
expected data for the machine.
Flash Rom error
The data in the flash ROM is not complete.
Auto Off Switch error
The main switch does not turn off for more
than 6.0 seconds.
Replace the MPU
E-51
E-61
4-2
Replace the MPU
Auto off switch defective
Auto off switch connector
disconnected
28 March 2006
ELECTRICAL COMPONENT DEFECTS
4.2 ELECTRICAL COMPONENT DEFECTS
C267T900.WMF
Jam Type
A Jam
B Jam
C Jam
D Jam
E Jam
P Jam
A or B Jam
TroubleService
Tables
shooting
Paper feed
Drum
Paper eject
Master feed
Master eject
ADF
Paper remaining
4.2.1 DRUM
Name
2 Feed start timing
Sensor
Master Eject Position
(HP) Sensor
Feed Start Timing
Sensor
nd
State
Open
Shorted
Open
Shorted
Open
Symptoms
E-22 is displayed when the drum rotates.
E-23 is displayed when the drum rotates.
E-24 is displayed when the drum rotates.
Shorted
Setting Drum: Normal Operation
No Drum: E-06 is displayed when the
main motor is rotates.
Displays “no drum”
Image will be patchy because ink will not
be supplied.
Display “Ink end”
Drum set
Set
OFF
Drum ink sensor
ON
OFF
4-3
ELECTRICAL COMPONENT DEFECTS
28 March 2006
4.2.2 PAPER EJECT
Name
Paper Exit Sensor
State
Open
Symptoms
The “C” jam indicator is lit.
The “B” jam indicator is lit when a copy is
made.
Shorted
4.2.3 PAPER FEED
Name
Paper Registration
Sensor
Paper Table Lower
limit Sensor
Paper End Sensor
State
Open
Symptoms
The “AB” jam indicator is lit.
The “A” jam indicator is lit when a copy is
made.
The paper table doesn’t go down.
The paper table goes down below the
sensor, and E-02 is displayed.
Printing can begin even if there is no
paper, and the “A” jam indicator will be lit.
The “load more paper” indicator is lit.
E-02 is displayed after 1 second from
moving up the paper feed table during
printing.
The paper table goes up over the sensor,
and E-02 is displayed
E-02 is displayed after 1 second from
moving up the paper feed table during
printing.
The paper table goes up over the sensor,
and E-02 is displayed
Shorted
Open
Shorted
Open
Shorted
Paper height sensor 1
Open
Shorted
Paper height sensor 2
Open
Shorted
4.2.4 MAIN DRIVE
Name
Clamper Open Sensor
State
Open
Symptoms
E-00 is displayed.
E-00 is displayed when the clamper
operates.
E-00 is displayed when the clamper
operates.
E-00 is displayed.
Shorted
Clamper Close
Sensor
Open
Shorted
4.2.5 SCANNER
Name
Platen Cover Sensor
State
Symptoms
The master is made normally, even if the
platen cover is open. (Have to push the
start button twice)
The image is treated using center/edge
erase mode.
E-13 is displayed.
Open
Shorted
Scanner HP Sensor
Open
Shorted
4-4
28 March 2006
ELECTRICAL COMPONENT DEFECTS
Name
Drum Master Sensor
State
On
Symptoms
The “B” jam indicator is lit when print is
started. (Print without master)
Master does not eject
The “D” jam indicator is lit.
E-12 is displayed.
The “Full eject master” indicator is lit.
E-12 is displayed.
E-12 is displayed.
The master is ejected, even if there is no
master eject box
“No master eject box” is displayed.
“Full eject master” indicator is lit.
The “B” and “E” jam indicator is lit.
The “B” jam indicator is lit
“Unit open” is displayed.
Off
Pressure Plate Limit
Sensor
Pressure Plate HP
Sensor
Master Eject Box
Sensor
Open
Shorted
Open
Shorted
On
Off
Master Eject Sensor
Master eject unit
safety switch
Open
Shorted
Open
Shorted
4.2.7 MASTER MAKING UNIT
Name
Master Set Cover
Sensor
Cutter HP Sensor
Master making unit
set switches
State
Open
Symptoms
The “D” jam indicator is lit.
The “open cover” indicators are lit.
Shorted
Open
Shorted
E-01 is displayed.
E-01 is displayed.
Either of sensors is work correctly, the
machine move correctly.
“Not set making unit” is displayed
Master making can start even if there is no
master roll, but the “D” jam indicator will
be lit.
The “load new master roll” indicator is lit.
E-09 is displayed.
E-04 is displayed.
On
Off
Master End Sensor
White
Thermal Head
Temperature
Black
Open
Short
4-5
TroubleService
Tables
shooting
4.2.6 MASTER EJECT
ELECTRICAL COMPONENT DEFECTS
28 March 2006
4.2.8 OTHER
Name
Auto shut off Switch
State
On
Symptoms
Cannot shut off the main switch.
E-61 is displayed at auto shut off.
The main switch stays off
Off
4-6
28 March 2006
DIP SW, LED, VR, TP, AND FUSE TABLES
4.3 DIP SW, LED, VR, TP, AND FUSE TABLES
4.3.1 TEST POINTS
MPU
No
TP5
TP10
TP11
TP23
TP25
TP28
Usage
GND-a
+5V
+5VE
Ink Detection Pulse
Standard Pulse
GND-a
4.3.2 POTENTIOMETERS
MPU
Usage
Ink detection adjustment
Master End Sensor Adjustment
TroubleService
Tables
shooting
No
VR1
VR2
Power Supply Unit
No
RV1
Usage
Thermal Head Voltage Adjustment
4.3.3 LED'S
MPU
LED #
LED 1
LED 2
LED 3
LED 4
OFF
CPU2 (not use for service)
Low Ink Condition
CPU1 (not use for service)
CPU1 (not use for service)
ON
Sufficient Ink Condition
4-7
DIP SW, LED, VR, TP, AND FUSE TABLES
28 March 2006
FUSES
MPU
FUSE #
FU 1
FU 2
Rated
Current
1A
2A
Voltage
24 V DC
5 V DC
Related Devices
Ink Pump Motor
UC2 PC Controller
PSU
FU 700
FU 701
Rated
Current
6.3 A
6.3 A
FU 702
FU 703
FU 704
6.3 A
8A
6.3 A
FUSE #
Voltage
Related Devices
120/230V AC AC Line
24VDC
Paper Transport Motor, Paper Feed Clutch,
Paper Up-Down Motor, Air Knife Fan Motor,
Front/Rear Pressure Release Solenoid,
Vacuum Fan Motor, Ink Pump Motor, Master
Eject Motor, Optional Key Counter, Master
Counter, Paper Counter, Cutter Motor, Clamper
Motor, Scanner Motor
24V DC
Not used
24V DC
Main Motor
24V DC
Optional Tape Dispenser
4-8
28 March 2006
ACCESSING SP MODES
5. SERVICE PROGRAM MODE
NOTE: The Service Program Mode is for use by service representatives only so
that they can properly maintain product quality. If this mode is used by
anyone other than service representatives for any reason, data might be
deleted or settings might be changed. In such case, product quality cannot
be guaranteed any more.
5.1 USING SERVICE PROGRAM MODES
Use the service program modes (SP modes) to check electrical data, change
operating modes, and adjust values.
5.1.1 ACCESSING SP MODES
Entering SP Mode
"→→→→D
• Hold the D key down for longer than 3 seconds.
Leaving SP Mode
Press the " key one or more times.
5-1
Service
Tables
1. Key in the following sequence.
HOW TO SELECT A PROGRAM NUMBER
28 March 2006
5.1.2 HOW TO SELECT A PROGRAM NUMBER
[E]
[G]
[D]
[B]
[F]
C267S900.WMF
[A]
[C]
1. Using the number keys [A] or the "$ keys [B], enter the desired main menu
number, then press the Enter key [C] or the OK key [D].
2. Using the number keys or the "$ keys, enter the desired sub-menu number,
then press the Enter key or the OK key.
3. Enter the desired value or mode using the number keys (SP modes are listed in
the service program tables).
NOTE: 1) Use the Memory/Class [E] key to toggle between “+” and “-“.
2) To enter a decimal place, you do not have to enter a decimal point.
For example, to enter “1.5” just press “1“ and “5“ keys.
4. Press the Enter key or the OK key to store the displayed setting.
NOTE: To cancel the SP mode, press the Clear Modes/Energy Saver key [F]
or the Cancel key [G].
5.1.3 MAIN MENU NUMBER LIST
Number
1
2
3
4
5
6
7
8
Main Menu
Copy Data
Basic Settings
System Settings
Input Mode
Output Mode
Adjustment
Memory Clear
System Test
5-2
28 March 2006
SP TABLE (SP 1-XXX)
5.2 1. COPY DATA
5.2.1 SP TABLE (SP 1-XXX)
Total master counter
Menu Items
20
Total print counter
50
51
52
53
54
55
56
57
58
D - master clamp jam
E - master eject jam
E - master compressing jam
A - paper non-feed jam
A - paper registration jam
B - paper wrapping jam
C - paper delivery jam
P - original feed - in jam
P - original feed - out jam
60
D - master cut jam
70
71
72
73
74
75
Main firmware part number
I/O ROM part number
Serial number
Main firmware version
ROM version
Serial number (Factory)
80
81
82
83
Error code history
Telephone number display
Jam history
PSU unusual voltage history
160
161
162
Japanese Display type (Japan only)
Key counter setting check
Key card setting check (Japan only)
Service
Tables
No.
1
5.2.2 SP1-70: MAIN FIRMWARE PARTS NUMBER
Displays the main firmware parts number and the suffix.
5.2.3 SP1-80: ERROR CODE HISTORY
Displays the latest 40 SC codes. Use the "$ keys to view the codes.
5.2.4 SP1-83: PSU UNUSUAL VOLTAGE HISTORY
Display the unusual power supply into the machine history.
5-3
SP TABLE (SP 2-XXX)
28 March 2006
5.3 2. BASIC SETTINGS
5.3.1 SP TABLE (SP 2-XXX)
No.
1
2
Menu Items
Default print speed
Default image position
Default
Settings
2
1 to 3
0
-10.0mm to +10.0mm (0.5mm
interval)
4
5
6
Destination code
Not used (Ink)
Image position display
10
Ink detection board
On
11
12
13
14
Paper end sensor
Drum master sensor
Platen cover sensor
ADF cover sensor
On
On
On
On
20
21
Destination setting
Ink setting (not used)
Other
0
33
Re - Feeding setting
40
41
42
43
44
45
T/H energy control – B4/Black
T/H energy control – B4/Color
T/H energy control – A4/Black
T/H energy control – A4/Color
T/H energy control – LG/Black
T/H energy control – LG Color
7
7
7
7
7
7
0 to 50%
0 to 50%
0 to 50%
0 to 50%
0 to 50%
0 to 50%
50
51
52
53
54
55
T/H energy control - B4/Black eco
T/H energy control - B4/Color eco
T/H energy control - A4/Black eco
T/H energy control - A4/Color eco
T/H energy control – LG/Black eco
T/H energy control – LG/Color eco
15
15
15
15
15
15
0 to 50%
0 to 50%
0 to 50%
0 to 50%
0 to 50%
0 to 50%
60
61
62
Bold letter mode
T/H Swing Mode
T/H Swing Quantity
Off
Off
2
Off/On
Off/On
+-1mm to +-5mm
80
Auto off at unusual voltage
On
Off/On
95
Paper table standby position
Low
High / Low
100
Make master without print
Off
Off/On
0
1
On
5-4
0 / 20:Slow 1:Normal 2:Fast
Off/On (Off is used for tests, and
for removing ink from the drum)
Off/On (Off is used for tests)
Off/On (Off is used for tests)
Off/On (Off is used for tests)
Off/On (Off is used for tests)
Other/Japan
0 to 1
Off/On
28 March 2006
SP2-6: IMAGE POSITION DISPLAY
5.3.2 SP2-6: IMAGE POSITION DISPLAY
When the user moves the image position on the operation panel, this SP controls
the length of time that the adjustment value is shown on the display before the
screen goes back to the previous display.
‘Slow’ means that the display is shown for the longest time possible.
5.3.3 SP2-33: RE-FEEDING SETTING
When the machine performs re-feeding, the paper registration position can be up to
5mm out of range. If this incorrect position is not acceptable to the customer,
change this SP mode to “OFF”.
ON: Re- feeding is on (factory setting).
OFF: Re- feeding is off.
5.3.4 SP2-40, 2-55: THERMAL HEAD ENERGY CONTROL
The default is 7%. This means that during normal printing mode, the
thermal head energy is 93% of the maximum possible (100 – 7).
2-50~55: The default is 15%. This means that in economy printing mode, the
thermal head energy is reduced by another 15%. With the default
settings, this means that the thermal head energy is 85% of maximum
power (100-15).
5.3.5 SP2-60: BOLD MODE: LETTER MODE ONLY
Makes a bold outline of a letter-mode image.
5.3.6 SP2-61: T/H SWING MODE
If this is set to ‘ON’, the thermal head writing position is moved a small amount
between masters. The amount is set with SP2-61 (T/H Swing Amount)
automatically. This changes the side-to-side margin on the master.
This prevents the same parts of the thermal head from being used all the time,
because if masters that contain the same image (such as a logo) are made
frequently, this can burn out the thermal head.
Default: OFF
5-5
Service
Tables
2-40~45:
SP2-62: T/H SWING AMOUNT
28 March 2006
5.3.7 SP2-62: T/H SWING AMOUNT
Settings: +-1 to +-5 mm
Default: 2 mm
5.3.8 SP2-80: AUTO OFF AT UNUSUAL VOLTAGE
There is an automatic detection system for unexpected voltage surges, featuring
automatic shut-off and data logging features.
5.3.9 SP2-95: PAPER TABLE STANDBY POSITION.
High: The paper table after printing is moved to a higher position than the standard
position. This will reduce the time for starting the first print when
continuously making masters.
Low: The standard position
NOTE: If SP2-95 is “high”, the machine goes to the standard position in the
following situations.
• When the master end indicator lights and a message is displayed
• When a master eject jam (B jam location indicator) is displayed
• When a master feed jam (D jam location indicator) is displayed
• When the paper height sensor is actuated immediately after the main
switch is turned on.
5.3.10 SP2-100: MAKE MASTER WITHOUT PRINT
This function wraps a blank master around the drum. The ink on the drum may dry
up at the following times:
• The machine is not used for a long time.
• The customer changes to a color drum that has not been used recently.
This might affect the print quality (Poor image: ghost image of the previous print).
Wrap a blank master around the drum after you print, to prevent ghost images of
previous prints when the machine is not used for a long time.
Procedure:
1) Access SP2-100 (Make master without printing). Then press “OK”.
2) Press the “Start” key while holding down the “#” key.
5-6
28 March 2006
SP TABLE (SP 3-XXX)
5.4 3. SYSTEM SETTINGS
5.4.1 SP TABLE (SP 3-XXX)
No.
1
2
3
4
9
10
Menu Items
Input the present time
Input TEL number
Input serial number
Input installation data
Key counter setting
Key card setting (Japan
only)
Default
(00/01/01 0:00)
(00/01/01)
No
No
Settings
99/12/31 23:59
99/12/31
No/Yes
No/Yes
5.4.2 SP3-1: INPUT THE PRESENT TIME
Input the last two digits of the present year (two-digit number).
↓#
Input the present month (two-digit number).
↓#
Input the present date (two-digit number).
↓#
Input the present hour (two-digit number).
↓#
Input the present minute (two-digit number).
↓#
Input the present second (two-digit number).
↓#
Example: 2003/January/27th/13:00:00
03
↓#
01
↓#
27
↓#
13
↓#
00
↓#
00
↓OK
5-7
Service
Tables
Input the year, the month / date, and the time in that order. Press the Enter key
between each one.
SP3-4: INPUT INSTALLATION DATE
28 March 2006
5.4.3 SP3-4: INPUT INSTALLATION DATE
Input installation date in that order. Press the Enter key between each one.
Input the last two digits of the present year (two-digit number).
↓#
Input the present month (two-digit number).
↓#
Input the present date (two-digit number).
↓#
Example: 2003/January/27th/13:00:00
03
↓#
01
↓#
27
↓OK
5-8
28 March 2006
SP TABLE (SP 4-XXX)
5.5 4. INPUT MODE
5.5.1 SP TABLE (SP 4-XXX)
Menu Items
Scanner HP sensor
Platen cover sensor
Master eject unit open SN
Master making unit set SW 1
10
11
12
13
14
15
16
17
18
19
Master making unit set SW 2
Master set cover sensor
Cutter HP switch
Master end sensor
Eject box set switch
Master eject sensor
Pressure plate HP sensor
Pressure plate limit Sensor
Ink detection signal
Color drum signal
21
22
23
24
25
27
28
Drum set signal
Clamper open sensor
Clamper close sensor
Drum master sensor
Master eject position SN
Drum size1 signal
Drum size2 signal
30
31
33
35
36
Table lowering switch
Table lower sensor
Paper end sensor
Paper pick-up roller sensor
Paper height filler sensor
41
42
43
44
Registration sensor
Feed start timing sensor
2nd feed timing sensor
Paper exit sensor
50
Door safety switch
No.
60
61
62
64
69
Menu Items
ADF connecting signal
ADF cover sensor
ADF registration sensor
ADF original set sensor
ADF open sensor
70 Key counter signal
71 Key card signal (Japan only)
Service
Tables
No.
1
2
7
9
5-9
SP TABLE (SP 5-XXX)
28 March 2006
5.6 5. OUTPUT MODE
5.6.1 SP TABLE (SP 5-XXX)
No.
1
2
3
4
8
9
10
11
12
13
14
15
Menu Items
Exposure lamp (xenon lamp)
Scanner motor - scan
Scanner motor - return
Scanner to HP
Master feed motor – Forward
Cutter motor – to HP
Cutter motor – reverse
Cutter motor – forward
VHD signal
Master eject motor
Pressure plate motor - limit
Pressure plate motor -to HP
No.
60
61
62
63
64
65
Menu Items
ADF motor
ADF feed clutch
ADF pick-up solenoid
Key counter signal
Not used
Key card (Japan only)
90
91
Main motor – to HP
Main motor – to Master clamp
100 All indicators on the panel
111 Auto Off solenoid
17
18
19
20
21
Main motor - 30 rpm
Main motor - 60 rpm
Main motor - 80 rpm
Main motor - 100 rpm
Main motor - 130 rpm
23
24
25
26
Clamper motor: to open
Clamper motor: to close
Ink pump motor
Pressure release solenoids
30
31
35
Table motor – down
Table motor – up
Paper feed clutch
40
41
42
43
44
Registration motor - 30 rpm
Registration motor - 60 rpm
Registration motor - 80 rpm
Registration motor - 100 rpm
Registration motor - 130 rpm
46
47
48
Air knife fan motors
Vacuum fan motor
PSU fan motor
50
51
Paper counter
Master counter
5-10
28 March 2006
SP TABLE (SP 6-XXX)
5.7 6. ADJUSTMENT
5.7.1 SP TABLE (SP 6-XXX)
Menu Items
Main-scan position – platen
Main-scan position – ADF
Scan start position – platen
Scan start position - ADF
Scanning speed - platen
Scanning speed - ADF mode
Default
0
0
0
0
0
0
10
11
Master writing speed
Master writing length
0
0
-5.0 to 5.0 %
-5.0 to 5.0 %
20
21
Registration buckle
Paper regist position
0
0
0 to100 PLS
-5.0 to 5.0 mm
27
28
29
30
Master making density
Master making density
Master making density
Master making density
1
1
1
1
0: Pale, 1: Normal, 2: Dark
0: Pale, 1: Normal, 2: Dark
0: Pale, 1: Normal, 2: Dark
0: Pale, 1: Normal, 2: Dark
32
33
34
35
36
37
MTF filter – Letter: Main
MTF filter – Letter: Sub
MTF filter – Letter/Photo: Main
MTF filter – Letter/Photo: Sub
MTF filter - Photo: Main
MTF filter – Photo: Sub
2
2
2
2
2
2
0 to 7
0 to 7
0 to 7
0 to 7
0 to 7
0 to 7
40
Ink detection adjustment
–
50
Master end sensor voltage
2
61
62
63
Master length – LG drum
Master length – B4 drum
Master length – A4 drum
70
71
72
SBU VRT value
SBU FBO value
SBU FBE value
–
–
–
100
101
102
103
104
108
109
Paper registration 30rpm
Paper registration 60rpm
Paper registration 80rpm
Paper registration 100rpm
Paper registration 130rpm
Paper regist: skip: 30rpm
Paper regist: skip: 60pm
0
0
0
0
0
0
0
- Tint
- Photo
- Letter/Photo
- Letter
4780
4780
4140
5-11
Settings
-5.0 to 5.0 mm
-5.0 to 5.0 mm
-2.0 to 5.0 mm
-5.0 to 5.0 mm
-5.0 to 5.0 %
-5.0 to 5.0 %
0.5 to 3.5V
4200 to 6000 (0.1mm)
4200 to 6000 (0.1mm)
3000 to 6000 (0.1mm)
-40 to 40
-40 to 40
-40 to 40
-40 to 40
-40 to 40
-40 to 40
-40 to 40
Service
Tables
No.
1
2
3
4
5
6
SP TABLE (SP 6-XXX)
28 March 2006
No.
Menu Items
110 Paper Regist: skip: 80rpm
111 Paper Regist: skip: 100rpm
112 Paper Regist: skip: 130rpm
Default
0
-40 to 40
0
-40 to 40
0
-40 to 40
116 Paper middle bulge 30rpm (Do not
Adjust)
117 Paper middle bulge 60rpm (Do not
Adjust)
118 Paper middle bulge 80rpm (Do not
Adjust)
119 Paper middle bulge 100rpm (Do not
Adjust)
120 Paper middle bulge 130rpm (Do not
Adjust)
0
-100 to 100
0
-100 to 100
0
-100 to 100
0
-100 to 100
0
-100 to 100
124 Paper front bulge 30rpm (Do not
Adjust)
125 Paper front bulge 60rpm (Do not
Adjust)
126 Paper front bulge 80rpm (Do not
Adjust)
127 Paper front bulge 100rpm (Do not
Adjust)
128 Paper front bulge 130rpm (Do not
Adjust)
0
-90 to 8
0
-90 to 8
0
-90 to 8
0
-90 to 8
0
-90 to 8
132
133
134
135
136
Paper Regist: A4 drum 30 rpm
Paper Regist: A4 drum 60 rpm
Paper Regist: A4 drum 80 rpm
Paper Regist: A4 drum 100 rpm
Paper Regist: A4 drum 130 rpm
0
0
0
0
0
-40 to 40
-40 to 40
-40 to 40
-40 to 40
-40 to 40
Paper Regist: skip: A4: 30 rpm
Paper Regist: skip: A4: 60 rpm
Paper Regist: skip: A4: 80 rpm
Paper Regist: skip: A4: 100 rpm
Paper Regist: skip: A4: 130 rpm
Paper middle bulge A4 30rpm(Do not
Adjust)
149 Paper middle bulge A4 60rpm(Do not
Adjust)
0
0
0
0
0
0
-40 to 40
-40 to 40
-40 to 40
-40 to 40
-40 to 40
-100 to 100
0
-100 to 100
150 Paper middle bulge A4 80rpm(Do not
Adjust)
151 Paper middle bulge A4 100rpm(Do not
Adjust)
152 Paper middle bulge A4 130rpm(Do not
Adjust)
156 Paper front bulge A4 30rpm(Do not
Adjust)
0
-100 to 100
0
-100 to 100
0
-100 to 100
0
-90 to 8
140
141
142
143
144
148
5-12
Settings
28 March 2006
SP6-10: MASTER WRITING SPEED
No.
Menu Items
157 Paper front bulge A4 60rpm(Do not
Adjust)
158 Paper front bulge A4 80rpm(Do not
Adjust)
159 Paper front bulge A4 100rpm(Do not
Adjust)
160 Paper front bulge A4 130rpm(Do not
Adjust)
Default
0
-90 to 8
0
-90 to 8
0
-90 to 8
0
-90 to 8
Settings
5.7.2 SP6-10: MASTER WRITING SPEED
130mm
Service
Tables
8mm
C267S902.WMF
1. Input SP8-10 (Test patterns) and enter “6”, then press the Start key.
2. Exit the SP mode, print 10 copies at 100 rpm (speed 2). Use the 10th print for
the adjustment.
3. The length of the 6 squares in the feed direction should be 130 mm, as shown
above.
4. If it is not, calculate the reproduction ratio using the following formula.
{(130 - Value) / 130} x 100 = ± X.X % (Round off to one decimal place)
Example: If the value is 133, {(130 - 133) / 130} x 100 = - 2.3 %
5. Access SP6-10, input the calculated ratio, and press the Enter key.
6. Repeat the procedure to make sure that the ratio is correct.
5-13
SP6-21: PAPER REGIST POSITION
28 March 2006
5.7.3 SP6-21: PAPER REGIST POSITION
1. Input SP8-10 (Test patterns) and enter “6”, then press the Start key.
2. Exit the SP mode, print 10 copies at 100 rpm (speed 2). Use the 10th print for
the adjustment.
3. The space between the leading edge and the next line should be 8 mm, as
shown above.
4. If it is not, access SP6-21, input the difference and press the Enter key.
Example: If the value is 7 mm, 7 - 8 = -1.0
5. Repeat the procedure to make sure that the gap is correct.
5.7.4 SP6-5: SCANNING SPEED – PLATEN AND SP6-6:
SCANNING SPEED – ADF MODE
1. Make copies of the test pattern printed during the previous adjustments (☛
previous page), in platen mode at speed 2. Use the 10th print for the
adjustment.
2. The length of the 6 squares in the feed direction should be 130 mm.
7. If it is not, calculate the reproduction ratio using the following formula.
{(130 - Value) / 130} x 100 = ± X.X % (Round off to one decimal place)
Example: If the value is 133, {(130 - 133) / 130} x 100 = - 2.3 %
3. Access SP6-05, input the calculated ratio, and press the Enter key.
4. Check again to make sure that the ratio is correct.
5. Make copies of the test pattern in ADF mode and repeat the process using
SP6-06.
5.7.5 SP6-3: SCANNING START POSITION – PLATEN AND SP6-4:
SCANNING START POSITION - ADF
1. Make copies of the test pattern printed during the previous adjustments (☛
previous page), in platen mode at speed 2. Use the 10th print for the
adjustment.
2. The space between the leading edge and the next line should be 8 mm.
3. If it is not, access SP6-03, input the gap value and press the Enter key.
Example: If the value is 7 mm, 7 - 8 = -1.0
4. Repeat the procedure to make sure that the gap is correct.
5. Make copies of the test pattern in ADF mode and repeat the process using
SP6-04.
5-14
28 March 2006
POSITION - ADF
SP6-1: MAIN SCAN POSITION – PLATEN AND SP6-2: MAIN SCAN
5.7.6 SP6-1: MAIN SCAN POSITION – PLATEN AND SP6-2: MAIN
SCAN POSITION - ADF
1. Make a copy in platen mode at speed 2.
2. Measure the difference between the center of the main-scan on the original and
on the print.
3. Access SP6-01, input the gap value and press the Enter key. (If you input a
positive value, the image moves towards the operation side.)
4. Repeat the procedure to make sure that there is no difference.
5. Make a copy in ADF mode and repeat the process using SP6-02.
5.7.7 IMAGE ADJUSTMENT (SP6-10, -21, -5, -3, AND -1)
Adjusts the image position on prints by changing the SP settings.
Adjust the settings in the order: SP6-10, -21, -5, -6, -3, -4, -1, -2.
When correcting errors made when printing with the controller, use only the first
two procedures. When correcting errors made when printing with scanned originals,
do all six adjustments in the given order.
Service
Tables
This adjustment is required every time the RAM on the MPU has been replaced.
5.7.8 SP6-20: REGISTRATION BUCKLE
Adjusts the paper skew and the paper registration slippage.
[A]
[B]
C267S903.WMF
[A]: Increase the value
The occurrence of paper skew will be reduced, but the paper is more likely to
slip and the registration position may be incorrect.
[B]: Decrease the value
The paper registration position will be correct.
5-15
SP6-32 TO 37: MTF FILTER
28 March 2006
5.7.9 SP6-32 TO 37: MTF FILTER
Sharpens the image, but moiré can become more apparent.
Refer to the following table for the relationship between this SP mode value and
filter strength (the relationship is not linear).
Value
7
6
0
5
4
3
2
1
Strength of Filter
X4
X2
X1
X 1/2
X 1/4
X 1/8
X 1/16
X 1/32
5.7.10 SP6-40: INK DETECTION ADJUSTMENT
Ensures that the CPU detects a no ink condition.
CAUTION: Before attempting this procedure, wipe off the ink around the ink roller.
To do this, set SP2-10 (ink detection) to OFF, and feed paper until ink
ends. After finishing the procedure, do not forget to return SP2-10 to
the default (ink detection on).
[A]
C267S904.WMF
Access SP6-40, and open the door cover. Then turn the VR1 [A] on the MPU board
until the display becomes “4.0 +-0.2 u” (4 µs).
NOTE: When the drum has ink inside, the machine displays “----“.
5-16
28 March 2006
SP6-100 TO 104: PAPER REGISTRATION - EACH SPEED
5.7.11 SP6-100 TO 104: PAPER REGISTRATION - EACH SPEED
The following procedure allows the image position to be adjusted for each speed
(30, 60, 80, 100 and 130 rpm)
NOTE: If you want to adjust the image position for all the speed at the same time,
use SP6-21 (Paper registration position).
1. Set SP8-10 (Test patterns) to a value of “6”, then press the Start key.
2. Make 3 copies at speed 3 (finishing with 130 rpm). Perform the adjustment
below for all 3 copies.
Trial print: 30 rpm
1st print: 60 rpm
2nd print: 80 rpm
3rd print: 100 rpm
4th print: 130 rpm
Service
Tables
3. The distance between the leading edge and first line should be 8mm, as shown
below.
C267S905.WMF
4. If this distance is not 8mm, access SP6-101 to 104 and then input a value to
adjust the distance (range: -40 to 40, step: 1) for each of 3 copies samples (i.e.
30, 60, 80, 100 and 130 rpm samples).
The higher the value, the narrower the distance between the leading edge and
1st line becomes (and vice-versa). Also, each step corresponds to
approximately 0.5mm. Input the value that will bring the distance to 8mm.
5. Perform the adjustment again for any of the samples that are still outside the
8mm standard.
NOTE: Adjust SP6-108 to 112, 132 to 144 in the same way.
5-17
SP TABLE (SP 7-XXX)
28 March 2006
5.8 7. MEMORY CLEAR
5.8.1 SP TABLE (SP 7-XXX)
No.
Menu Items
1 Factory settings clear
3 Total counter clear
4 Jam/Error data clear
5.8.2 SP7-1: FACTORY SETTINGS CLEAR
This resets all SP and User tool settings except for the following SP and User tool
numbers.
•
•
•
•
•
•
•
•
•
User tool 1: Counter Display (Masters and Prints)
User tool 2-4: mm/inch
User tool 2-5: Language on LCD
User tool 2-6: Date/Time
SP2-4: Destination code
SP2-20: Destination setting
SP2-80: Auto off at unusual voltage
SP3-3: Input serial number
SP6-All: Adjustments
5.8.3 SP7-3: TOTAL COUNTER CLEAR
This resets the following SP numbers
• SP1-1 Total master counter
• SP1-20 Total print counter
NOTE: The counters for “User tool 1: Counter Display” are unresetable counter
5-18
28 March 2006
SP TABLE (SP 8-XXX)
5.9 8. SYSTEM TEST
5.9.1 SP TABLE (SP 8-XXX)
No.
1
2
3
4
5
9
Menu Items
Download main firmware
Upload main firmware
Data printout – Basic/SC/Jam
Data printout – Adjustment
Data printout – Input/Output
Data printout – Power failure
Default
Settings
Start with # key
Start with # key
-
10
19
Test patterns
Free run - ADF
6
100%
20
21
22
Free run - scanner
Paper feed at 30rpm
Free run - Paper feed
100% 65%~155%
Off
Off/On
Off
Off/On
Off
Active when start press
Off/On
Service
Tables
30 All indicators on panel
31 LCD data download (Do not use)
100 Drum size/type check
1 to 9 A4 start with #
65%~155%
5-19
SP8-1. DOWNLOAD MAIN FIRMWARE
28 March 2006
5.9.2 SP8-1. DOWNLOAD MAIN FIRMWARE
[A]
[B]
C267S906.WMF
Updates the main firmware using a flash memory card [A].
NOTE: To update the I/O control firmware in the EPROM on the MPU, replace the
EPROM (see section 3.12).
1. Before downloading new firmware, check the current version with SP1-70
2. Prepare a flash memory card with the latest firmware.
3. Turn off the main switch and disconnect the power cord.
4. Remove the rear card cover [B].
5. Plug the flash memory card into the connector on the MPU.
6. Connect the power cord, then turn on the main switch.
7. Access SP8-1 and press the OK key. Press the “Enter(#)” key.
8. Press the Enter key. (It takes about 2.0 minutes to complete.)
9. Check that the “Completed” is displayed.
10. Turn off the main switch, and remove the flash memory card.
5.9.3 SP8-2: UPLOAD MAIN FIRMWARE
Writes firmware to a flash memory card (P/N’ #A2309352 or N8036701) from the
machine.
1. Refer to steps 3 to 5 of section 5.9.2 (download main firmware).
2. Connect the power cord, then turn on the main switch while holding the Clear
Modes key.
3. Access SP8-2 and press the OK key. Press the “Enter(#)” key.
Refer to steps 8 and 10 in section 5.9.2 (download main firmware).
5-20
28 March 2006
SP8-9 DATA PRINTOUT – POWER FAILURE
5.9.4 SP8-9 DATA PRINTOUT – POWER FAILURE
[A]
[B]
[D]
Service
Tables
[C]
C267S901.WMF
[A]: Momentary Voltage Drop
[B]: Over voltage
[C]: Low voltage
[D]: High voltage
The machine collects information about unusual voltages from the power outlet and
you can check this data with SP 8-9 Data printout – Power failure
See section 6.11 for more information about the four types of data ([A] to [D]).
5-21
SP8-10: TEST PATTERNS
28 March 2006
5.9.5 SP8-10: TEST PATTERNS
Makes prints without using the scanner.
Access SP8-10 and select the number “6”, then press the “Enter(#)” key.
Other numbers are as shown below
1: Grid, 2: Vertical, 3: Horizontal gray, 4: Vertical gray, 5: 16 grays,
6: Cross, 7: Diagonal grid, 8: 256 grays, 9: 64 grays
5.9.6 SP8-21: PAPER FEED TEST (30 RPM)
Feeds paper at the lowest speed (30 rpm), and applies printing pressure.
1. Set a stack of paper on the paper feed table.
2. Access SP8-21 and press the OK key.
3. Exit the SP mode and enter the number of sheets that you want to feed.
4. Press the Print key.
5. To exit this mode, turn off the main switch.
5.9.7 SP8-22: FREE RUN PAPER FEED (30 RPM)
Drives the paper feed mechanism at the lowest speed (30 rpm) without paper.
1. Access SP8-22 and press the OK key.
2. Exit the SP mode and enter the number of times that you want to repeat the
paper feed cycle.
3. Press the Print key.
4. To exit this mode, turn off the main switch.
5-22
28 March 2006
MAIN MENU NUMBER LIST
5.10 USER TOOLS
5.10.1 MAIN MENU NUMBER LIST
Number
1
2
3
4
5
6
7
Main Menu
Counter
System Settings
Set Operation Mode
Initial Settings
Mode Settings
Administration Tools
Online Settings
5.10.2 USER TOOL LISTS
1. Counter
No.
1
Mode
Counter Display
Description
Shows the total number of masters and prints.
No.
1
Mode
Auto Reset Timer
2
4
Disp. Resettable
Counter
Reset Resettable
Counter
mm/inch
5
6
Language on LCD
Date/Time
7
Energy Saver Option
8
Energy Saver Timer
9
10
Auto Off Timer
Data Print
3
Description
The machine automatically returns to its initial condition if
it has not been operated for a certain period of time.
Shows the total number of masters and prints after
resetting.
You can select whether or not to clear the number of
resettable counter
You can select the units of measurement used on the
panel display.
You can select the language for the panel display.
You can set the date and time for the machine's internal
clock using the number keys.
You can select the energy saver mode from Energy
Saving or Auto Off.
You can specify the time taken for the machine to enter
Energy Saver mode.
You can select to use the auto off timer.
You can print the log data and the counter list.
5-23
Service
Tables
2. System
USER TOOL LISTS
28 March 2006
3. Set Operation Mode
No.
1
2
3
4
5
Mode
Description
Minimum Print Quantity You can set a minimum print quantity between 0 and
9999. Any number below the minimum will not be printed.
Maximum Print
You can set a maximum print quantity between 0 and
Quantity
9999.
Panel Beeper
You can turn the beeper on or off.
LCD Contrast
You can adjust the brightness of the panel display.
Class Display
Under the Memory/Class function, you can select to have
“Select Class/Year” displayed as “Select Department”
instead, when the machine is not limited to school or
college use.
4. Initial Settings
No.
1
Mode
Master Making Density
2
Original Type
3
Ratio
4
Economy Mode
5
6
7
Erase Border Width
Program/ Change Class
Program/ Change
Memory
Prog.Change:
Class/Year
8
Description
You can specify the image density that is selected by
default when the power is turned on.
You can specify the original type that is selected by
default when the power is turned on.
You can specify the reproduction ratio that is selected by
default when the power is turned on.
You can select to have Economy mode as either “On” or
“Off” when the power is turned on, or after mode settings
have been cleared.
You can specify the edge erase margin.
You can store settings of the Class mode
You can store settings of the Memory mode”
You can store settings of the Select Class/Year.
5-24
28 March 2006
USER TOOL LISTS
5. Mode Settings
Mode
Auto Cycle
2
Background Correction
3
Longer Paper
4
Combine/Repeat Priority
5
6
Cmb / Img Repeat Sep.
Line
Cancel Combine setting
7
Skip Feed
8
Memory Mode Setting
9
Auto Class
Description
You can select to have Auto Cycle mode as either “On”
or “Off” when the power is turned on.
When you make prints in Photo, or Text/Photo mode, the
background of the prints might appear dirty. In this case,
you can select background correction to improve the
clarity of your prints.
If you are making prints on paper of custom sizes, you
can set “Use”.
You can choose to have either Combine or Repeat
selected by default when the power is turned on.
You can specify the type of separate line of combine and
repeat.
You can specify whether Combine/Repeat mode will be
automatically cleared after you have finished your print
job.
You can specify the number of times that the drum
rotates when in Skip Feed mode.
You can choose to have either Memory mode or Stack
Memory mode as the default.
Under the Class mode, the machine stops after it is
finished a Class print job. When you select Auto Class,
the machine stops for 2 seconds and then goes on to the
next Class print job.
Service
Tables
No.
1
6. Administrator Tools
User Codes
If user codes are turned on, operators must enter their user codes before they
can operate the machine. The machine keeps count of the number of masters
and prints made under each user code.
No.
1
2
3
4
Mode
Display Counter(s)
Clear Counter(s)
User Code Management
Key Counter Adjust
Description
You can check the number of masters and copies made
under each user code.
You can clear each or all user code counters.
You can select whether or not to use User Code mode.
Normally, the optional key counter counts the number of
prints regardless of the number of masters used. You
can, however, add to the key counter a value between 0
and 50 to the key counter each time a new master is
used.
7. Online Settings
No.
1
Mode
Hold Data-in
Description
You can select to have Hold Data-in mode either “On” or
“Off” when the power is turned on, or after mode settings
have been cleared.
5-25
28 March 2006
MECHANICAL COMPONENT LAYOUT
6. DETAILED SECTION DESCRIPTIONS
6.1 MECHANICAL COMPONENT LAYOUT
25
24
23
22
21
20
19
18
27
26
28
29
1
2
3
4
5
6
7
17
8
15
14
13
12
11
10
9
1. Tension Roller
16. Paper Delivery Table
2. Master Feed Roller
17. Air Knife Fan Motor
3. Platen Roller
18. Master Eject Box
4. Thermal Head
19. Master Eject Rollers
5. Master Roll
20. 3rd Mirror
6. Paper Feed Roller
21. 2nd Mirror
7. Paper Pick-up Roller
22. 1st Mirror
8. Paper Table
23. DF Exposure Glass
9. Registration Rollers
24. 1st Transport Roller
10. Doctor Roller
25. Separation Roller
11. Press Roller
26. Original Feed Belt
12. Ink Roller
27. Pick-up Roller
13. Vacuum Fan Motor
28. 2nd Transport Roller
14. Exit Pawl
29. Original Exit Roller
15. Transport Belts
6-1
C267D004.WMF
Detailed
Descriptions
16
ELECTRICAL COMPONENT LAYOUT
March 2006
6.2 ELECTRICAL COMPONENT LAYOUT
6.2.1 MAIN BODY
22
24
23
25
21
20
1
2
19
18
17
16
15
3
4
5
6
7
14
13
12
11
9
C267D005.WMF
8
10
47
48
49
50
46
26
27
28
45
29
44
30
43
42
31
41
32
40
33
39
38
37
36
6-2
35
34
C267D006.WMF
28 March 2006
ELECTRICAL COMPONENT LAYOUT
Boards
Index No.
18
19
21
25
43
48
Name
LCD
Operation Panel Boards
Lamp Stabilizer
SBU
Main Processing Unit
(MPU)
Power Supply Unit
Function
Displays messages for the operator
These boards control the operation panel.
This supplies power to the xenon lamp.
Makes a video signal from the scanned original.
Controls all machine functions both directly and
through other boards.
Provides dc power to the system.
Index No.
1
4
11
15
29
30
Name
Scanner Motor
Master Feed Motor
Paper Table Motor
Cutter Motor
Master Eject Motor
Air Knife Fan Motor
32
Vacuum Fan Motor
34
36
40
Pressure Plate Motor
Clamper Motor
Main Motor
41
Registration Motor
45
Original Feed Motor
Function
Stepper motor drives the book scanner.
Feeds the master to the drum.
Raises and lowers the paper table.
Cuts the master.
Sends used masters into the master eject box.
Rotates the fan to provide air to separate the
leading edge of the paper from the drum.
Provides suction so that paper is held firmly on the
transport belt.
Raises and lowers the pressure plate.
Opens or closes the drum master clamper.
Drives paper feed mechanisms, the drum, and the
paper delivery unit.
Feeds the paper to align it with the master on the
drum.
Stepper motor drives the book scanner.
Name
Front Pressure Release
Solenoid
Rear Pressure Release
Solenoid
Function
Releases the press roller to apply printing
pressure.
Releases the press roller to apply printing
pressure.
Name
Master making unit set
switches
Paper Table Lowering
Switch
Master eject unit safety
switch
Door Safety Switches
Cutter HP Switch
Function
The machine does not work until the two set
switches turn on.
Lowers the paper table.
Solenoids
Index No.
13
38
Switches
Index No.
9, 14
12
16
17
24
Checks whether the master eject unit is properly
closed.
Checks whether the front door is properly closed.
Detects when the cutter is at the home position
6-3
Detailed
Descriptions
Motors
ELECTRICAL COMPONENT LAYOUT
Index No.
28
March 2006
Name
Main Switch
Function
Turns the power on or off.
Function
Checks if the master set cover is set.
3
Name
Master Set Cover
Sensor
Master End Sensor
6
Paper Height Sensor 1
7
Paper Height Sensor 2
8
Paper End Sensor
10
Paper Registration
Sensor
Scanner Home Position
Sensor
Platen Cover Sensor
Sensors
Index No.
2
24
25
26
27
31
33
35
37
39
42
46
47
49
50
Master Eject Sensor
Drum Master Sensor
Paper Exit Sensor
Pressure Plate Limit
Sensor
2nd Feed start Timing
Sensor
Clamper Open Sensor
Clamper Close Sensor
Paper Table Lower Limit
Sensor
Feed Start Timing
Sensor
Master Eject Position
Sensor
Pressure Plate Home
Position Sensor
Eject Box Set Sensor
Informs the CPU when the master making unit
runs out of master roll.
Detects when the paper table reaches the paper
feed position.
Detects when the paper table reaches the paper
feed position.
Informs the CPU when the paper table runs out of
paper.
Detects paper approaching the registration roller.
Detects when the image sensor is at home
position.
Detects whether the platen cover is open or
closed.
Detects used master misfeeds.
Detects if there is a master on the drum
Detects paper misfeeds at the exit.
Detects if the pressure plate is in the lowest
position.
Determines the paper misfeed check timing at the
paper registration area.
Detects if the clamper is in the open position.
Detects if the clamper is in the closed position.
Detects when the paper table is at its lower limit
position.
Determines the paper feed start timing.
Detects when the drum is at the master eject
position (this is the home position)
Detects if the pressure plate is at the home
position.
Checks if the master eject box is set.
Others
Index No.
5
20
44
Name
Thermal Head
Xenon Lamp
Paper Feed Clutch
Function
Burns the image onto the master.
Applies light to the original for exposure.
Transmits main motor drive to the paper feed roller
at the appropriate time.
6-4
28 March 2006
DRIVE LAYOUT
6.3 DRIVE LAYOUT
8
1
7
6
2
5
C267D007.WMF
4
3
5. Paper Feed Clutch
2. Clamper Motor
6. Master Feed Motor
3. Main Motor
7. Scanner Motor
4. Registration Motor
8. Original Feed Motor
Detailed
Descriptions
1. Pressure Plate Motor
6-5
SCANNER AND OPTICS
March 2006
6.4 SCANNER AND OPTICS
6.4.1 SCANNER OVERVIEW
1
3
2
4
5
6
C267D025.WMF
1. Exposure Lamp
2. 1st Scanner
3. Exposure Glass
4. Lens Block
5. Scanner Motor
6. Scanner H.P. Sensor
The original is illuminated by the exposure lamp (a xenon lamp). The image is
reflected onto a CCD (charge coupled device) on the lens block via the 1st, 2nd,
and 3rd mirrors, and through the lens on the lens block.
The 1st scanner consists of the exposure lamp, a reflector, and the 1st mirror.
A lamp stabilizer energizes the exposure lamp. The light reflected by the reflector is
of almost equal intensity, to reduce shadows on pasted originals.
There is no original size detection. All masters are printed at full size.
ICP1
Lamp Stabilizer Fuse
C267D935.WMF
ICP1
Rating
DC50 V/1.5 A
Manufacturer
ROHM CO.,LTD
6-6
Type No.
ICP–N38
28 March 2006
SCANNER AND OPTICS
6.4.2 SCANNER DRIVE
[I]
[G]
[A]
[B]
[C]
[D]
[H]
[E]
[F]
C267D026.WMF
A stepper motor drives the 1st and 2nd scanners [A, B]. The 1st scanner is driven
by the scanner drive motor [C], timing belt [D], scanner drive pulley [E], scanner
drive shaft [F], and two timing belts [G]. The 2nd scanner is driven through the 1st
scanner and two timing belts [H].
In reduction or enlargement mode, the scanning speed depends on the
magnification ratio. The returning speed is always the same, whether in full size or
magnification mode. The image length change in the sub scan direction is done by
changing the scanner drive motor speed, and in the main scan direction it is done
by image processing on the MPU board.
Magnification in the sub-scan direction can be adjusted by changing the scanner
drive motor speed using SP6-5. Magnification in the main scan direction can be
adjusted using SP6-1.
- ADF mode The scanners are always kept at their home position (the scanner H.P. sensor [I]
detects the 1st scanner) to scan the original. The ADF motor feeds the original
through the ADF. In reduction/enlargement mode, the image length change in the
sub-scan direction is done by changing the ADF motor speed. Magnification in the
main scan direction is done in the MPU board, like for book mode.
Magnification in the sub-scan direction can be adjusted by changing the ADF motor
speed using SP6-6. In the main scan direction, it can be adjusted with SP6-2, like
for book mode.
6-7
Detailed
Descriptions
- Book mode The MPU controls and operates the scanner drive motor. In full size mode, the 1st
scanner speed is 200 mm/s during scanning. The 2nd scanner speed is half that of
the 1st scanner.
IMAGE PROCESSING
March 2006
6.5 IMAGE PROCESSING
6.5.1 IMAGE PROCESSING FLOW
Image processing is done by the IPU (Image Processing Unit) on the MPU board,
following the steps shown below.
Shading Correction
↓
Reduce/Enlarge
↓
Filtering
↓
Gamma Correction
↓
Grayscale Processing
Shading Correction:
Corrects errors in the signal level for each pixel using the white plate.
Reduce / Enlarge:
Reduces or enlarges the image in the main-scan direction by data processing.
(Image magnification in the sub-scan direction is controlled by changing the
scanning speed.)
Filtering:
Improves the scanned image data, to make the image as close to the original as
possible.
Gamma Correction:
Background erase
Grayscale Processing:
Compares each pixel with surrounding pixels to enhance the image.
• Text mode: Binary processing
• Photo mode: Error diffusion
6-8
28 March 2006
IMAGE PROCESSING
6.5.2 THERMAL HEAD
Specifications
• Length
• Number of thermal head elements
• Density of thermal head elements
• Applied voltage
256 +- 0.2 mm
3024 dots
300 dpi
Approximately 15 volts
Thermal Head Control
The thermal head has heating elements at a density of 300 dpi. The thermal
heating elements melt the over-coating and polyester film layers of the master,
according to the image signal for each pixel.
The power supply unit applies power to the thermal heating elements. The power
source varies from one head to another since the average resistance of each
element varies. Therefore, when the thermal head or power supply unit is replaced,
it is necessary to readjust the applied voltage with particular values for each
thermal head.
Thermal Head Protection
SC Code
Conditions
E - 04
E - 09
Over 65°C
More than 4.432V - (Normally, this indicates
that the thermistor has become open, or a
related connector is disconnected.)
When the pulse width that controls the thermal
head energy becomes abnormal, master
making stops and this SC lights.
The CPU detects an abnormal ID signal from
the thermal head.
E - 10
E-40
6-9
Detecting
Component
Thermistor
Thermistor
MPU
MPU
Detailed
Descriptions
The thermistor on the thermal head provides thermal head protection, preventing
the thermal head from overheating when processing a solid image. The CPU
detects any abnormal condition when the Start key is pressed, and displays an SC
code on the operation panel as follows:
MASTER EJECT UNIT
March 2006
6.6 MASTER EJECT UNIT
6.6.1 OVERVIEW
[D]
[F]
[B]
[A]
[C]
C267D936.WMF
[E]
The master eject unit removes the used master from the drum. (☛!: Digital
Duplicators – Duplicating Process – Master Ejecting)
Procedure
The drum turns to the master eject position (same as drum home position). Then
the clamper [A] opens.
↓
Master eject rollers [B] pick-up the master’s leading edge and feed the master for 1
second into the master eject box [C].
↓
The clamper then closes.
↓
The drum then turns at 30 rpm while the master eject rollers continue to feed the
used master into the eject box.
↓
After the drum makes 1.5 turns, it gets to the master feed position. Then, the
master eject motor stops, and the pressure plate [D] then compresses the used
masters in the eject box.
• The capacity is 30 used masters (under normal conditions)
• The master eject process is skipped when the drum master sensor [E] detects no
master on the drum.
• During the master eject process, the master eject sensor [F] detects master eject
jams.
6-10
28 March 2006
MASTER EJECT UNIT
6.6.2 MASTER EJECT UNIT OPEN MECHANISM
[A]
[B]
C267D030.WMF
To open the master eject unit, just push the button [A]. This makes it easy for
maintenance and for removing master and paper jams.
Detailed
Descriptions
If the button is pushed by accident while the machine is operating, the master eject
unit safety switch [B] will stop the machine automatically for safety.
6-11
MASTER EJECT UNIT
March 2006
6.6.3 MASTER CLAMPER OPENING MECHANISM
[F]
[D]
[I]
[K]
[H]
[J]
[C]
[B]
[G]
C267D008.WMF
[A]
[E]
Clamper Mechanism
Clamper motor [A] - opens the clamper at the master eject position
↓
Gears [B]
↓
Link [C]
↓
Drum guide [D] - moves and engages the pin on the rear flange of the drum
↓
Lifts the clamper lever [E], and engages the drum pin [F]
↓
The lever [E] lifts the master eject arm [G] to release the master's leading edge [H]
from the clamper.
NOTE: 1) After the master making key is pressed and before the clamper motor
starts, the master eject position sensor [I] is checked (the drum must be
at the master eject position).
2) The sensor actuators on the link [C], the clamper open sensor [J], and
the clamper close sensor [K] determine the clamper open and close
positions.
3) The master clamper uses a magnetic plate to clamp the master's
leading edge.
4) The drum guide catches the drum at the master eject position while the
master clamper is being opened. When the clamper motor turns on in
reverse to close the clamper, the drum guide also disengages the pin
and the drum can turn.
6-12
28 March 2006
MASTER EJECT UNIT
6.6.4 MASTER EJECT ROLLER MECHANISM
[C]
[D]
[B]
C267D937.WMF
[A]
NOTE: During this process, the master eject sensor [D] detects master eject jams.
6-13
Detailed
Descriptions
Mechanism
Master eject motor [A]
↓
Gears [B]
↓
Master eject rollers [C] – the upper roller has paddles
↓
Pick up the master and feed it into the master eject box
MASTER EJECT UNIT
March 2006
6.6.5 PRESSURE PLATE MECHANISM
[C]
[B]
[D]
[E]
[A]
C267D938.WMF
Mechanism
Pressure plate motor [A]
↓
Gears [B]
↓
Pressure plate rotates
↓
Compresses the masters
Procedure
1. After the master has been ejected and the drum is stopped at the master feed
position, the pressure plate motor turns until the actuator on the pressure plate
actuates the limit sensor [D].
2. After master making and cutting, the motor reverses until the pressure plate
home position sensor [C] is actuated, then it stops.
3. If the pressure plate limit sensor is not actuated within 2.2 seconds after the
pressure plate motor rotates, the Full Master Eject Box indicator lights.
4. The spring [E] prevents motor overload.
6-14
28 March 2006
MASTER FEED
6.7 MASTER FEED
6.7.1 OVERVIEW
[A]
[B]
[E]
[D]
[C]
C267D939.WMF
The master making unit makes an image on the master and feeds the master to
the drum. (☛!: Digital Duplicators – Duplicating Process – Master Feeding)
The machine feeds the master from the master roll [A].
↓
The thermal head [B] makes an image on the master.
↓
Clamper [C] opens. (The drum is at the master feed position.)
↓
The clamper clamps the master.
↓
The master is wrapped around the drum [D]. Then, the cutter [E] cuts the master.
Then, after cutting, the drum turns a bit more to complete the wrapping.
6-15
Detailed
Descriptions
Procedure
MASTER FEED
March 2006
6.7.2 MASTER FEED MECHANISM
[C]
[D]
[F]
[B]
[E]
C267D009.WMF
[A]
Mechanism
Master feed motor [A] (stepper motor)
↓
Gears [B]
↓
Platen roller [C], master feed roller [D]
↓
Feeds the master (The thermal head makes an image on the master.)
Procedure
1. After the old master has been ejected, the drum stops at the master feed
position and the master clamper opens, ready to clamp the new master.
2. When the clamper is open, the tension roller releases and the master is fed to
the clamper on the drum. For details of the tension roller, see section 6.7.3.
3. After the clamper closes, the master feed motor feeds the master while the
drum rotates intermittently at 30 rpm. The intermittent rotation keeps a buckle
[F] in the master above the master feed guide to absorb shocks from the
wrapping operation.
4. The tension roller [E] keeps the master under tension. This roller reduces the
master making time, because it allows the drum to turn continuously during
wrapping. Without this roller, if the drum kept turning, the master would crease.
5. The main motor turns off when the drum is at the master eject position. The
master feed motor continues to feed the master until master making completed.
Then the master feed motor turns off, and cutting is done. Then the main motor
turns on again to complete the wrapping.
NOTE: Springs press the thermal head against the platen roller. The pressure is
applied when the master set cover, which includes the platen roller, is
closed.
6-16
28 March 2006
MASTER FEED
6.7.3 CLAMPER AND TENSION ROLLER MECHANISM
[F]
[A]
[G]
[B]
[C]
[H]
[D]
[I]
[E]
C267D010.WMF
[H]
Detailed
Descriptions
[G]
C267D940.WMF
6-17
MASTER FEED
March 2006
Mechanism
Clamper motor [A]
↓
Gears [B]
↓
Link [C]
↓
Drum guide [D]
↓
Lifts the lever [E], engages and locks the drum pin [F], opens the clamper plate [G].
↓
Releases the tension roller [H].
↓
Feeds the master into the clamper.
Procedure
• When the old master has been ejected, the drum is stopped at the master feed
position. The master clamper clamps the leading edge of the new master before
the drum starts to turn again.
• The tension roller [H] normally presses against the master feed guide plate to
apply tension to the master during master wrapping. When the clamper opens, it
pushes the tension roller arms [I] and moves the tension roller away from the
guide plate to allow the master to be fed into the master clamper.
• Clamper mechanism: See the section 6.6.3 Master Clamper Opening
Mechanism.
6-18
28 March 2006
MASTER FEED
6.7.4 CUTTER MECHANISM
[B]
[A]
C267D941.WMF
• When the cutter starts, the drum is stopped at the master eject position (drum
HP).
• The cutter moves backwards and forwards. While the cutter travels towards the
rear (non-operation side), it cuts the master. The motor turns in one direction.
The cutter returns to the home position when it reaches the rear because of the
two different spiral threads on the screw shaft.
• The cutter usually cuts a master of about 474 mm in length.
After cutting, the drum starts turning again to wrap the remaining part of the master
around the drum. The leading edge of the master that was cut remains at the
cutting position, ready to make the next master.
6-19
Detailed
Descriptions
[A]: Cutter motor
[B]: Cutter HP sensor
MASTER FEED
March 2006
6.7.5 MASTER SET COVER SENSOR
[C]
[B]
[A]
C267D011.WMF
[A]: Master set cover sensor
[B]: Master set cover
NOTE: If the cover is closed properly, the release button [C] rises.
6-20
28 March 2006
MASTER FEED
6.7.6 MASTER MAKING UNIT SLIDE-OUT MECHANISM
[D]
[C]
[E]
[A]
C267D031.WMF
[B]
The master making unit [A] can be pulled out along the guide rails [B].
There are two master making unit set switches [E] for safety, because this model
does not have a unit locking mechanism. Both sensors must be on, or the machine
will not start. When one of the sensors detects the unit is open, the operation panel
displays a message.
6-21
Detailed
Descriptions
There are four cable connectors [C] behind the master making unit. The bundle of
harnesses [D] is placed in the space between the scanner and the drum, and
connected to the MPU.
MASTER FEED
March 2006
6.7.7 MASTER SET MECHANISM
[A]
C267D942.WMF
The convex part [A] at the arrows helps the user when installing a new roll, so that
the user does not push the leading edge too far into the interior of the master
making unit.
6-22
28 March 2006
DRUM
6.8 DRUM
6.8.1 OVERVIEW
[C]
[D]
[A]
[B]
C267D943.WMF
Procedure
Ink is supplied inside the drum, through the drum shaft.
The ink roller [A] and the doctor roller [B] spread the ink evenly on the screens.
↓
Ink passes through the metal screen [C].
↓
Ink passes through the cloth screen [D].
↓
Ink passes through the holes in the master that were made by the thermal head.
↓
Ink reaches the paper.
NOTE: 1) The drum is driven by the main motor and turns only clockwise.
2) The main motor speed and the drum stop positions are controlled by
monitoring the motor encoder.
3) The ink pump supplies ink from the ink cartridge into the drum through
the drum shaft.
6-23
Detailed
Descriptions
↓
DRUM
March 2006
6.8.2 DRUM DRIVE MECHANISM
[D]
[C]
[E]
[A]
[B]
C267D012.WMF
Mechanism
Main motor [A] (dc motor)
↓
Belt [B]
↓
Gears [C]
↓
The drum rotates.
NOTE: 1) The main motor encoder sends pulses to the main motor control board
(1020 pulses = 360 degrees).
2) The CPU monitors the pulses and controls the drum speed and stop
positions.
3) The drum has two sensors;
• Master eject sensor [D] (master eject position and drum home
position)
• Feed start timing sensor [E]
4) The drum has two stop positions;
• Master eject (drum home) position
• Master feed position (feed start timing sensor + 102 pulses)
6-24
28 March 2006
DRUM
6.8.3 INK SUPPLY MECHANISM
[C]
[E]
[D]
[A]
C267D013.WMF
[B]
Ink is supplied from the ink cartridge to the ink roller [B] by a trochoid type pump [C].
The ink pump is driven by the ink supply motor (a dc motor) [D].
Ink drops through the holes in the drum shaft [A] onto the ink roller [B].
NOTE: 1) There are 4 holes in the shaft for the B4 size drum models, and two
holes for the Legal and A4 drum versions.
2) Optional drum units do not use the trochoid type pump, but use a piston
pump.
6-25
Detailed
Descriptions
There is an ink filter [E] at the entrance of the ink nozzle. The ink filter prevents
small objects from getting into the ink pump and causing damage.
DRUM
March 2006
6.8.4 INK ROLLER MECHANISM
[A]
[E]
[C]
C267D944.WMF
Main motor
[D]
[B]
↓
[F]
Gears [A]
↓
Ink roller [B] rotates
↓
Gears [C]
↓
Doctor roller [D] rotates
↓
The doctor roller squeezes the ink on the ink roller to produce an even thickness of
ink on the ink roller.
NOTE: 1) The ink roller drive gear [E] has a one-way clutch to prevent the ink
roller from being turned in reverse if the drum is manually turned in
reverse.
2) The ink roller does not touch the metal screen when the machine is not
printing.
3) During printing, the ink on the ink roller is applied to the paper through
the holes in the screens and the master. This happens when the press
roller [F] under the drum moves up to press the drum screen and the
master against the ink roller. (☛!: Digital Duplicators – Ink Supply
Control)
6-26
28 March 2006
DRUM
6.8.5 INK SUPPLY CONTROL
[A]
[B]
[C]
[D]
C267D014.WMF
Mechanism
When the ink level is low, the pins [A] do not touch the ink.
↓
NOTE: 1) The ink detection pins [A] detect the capacitance of the ink between the
ink roller [B] and doctor roller [C].
2) If the pins detect an insufficient amount of ink after activating the ink
pump motor for 27 seconds, a "no ink condition" is detected. The add
ink indicator on the operation panel will light.
3) The ink roller blades [D] on both ends of the ink roller scrape off the
built-up ink on the ends of the ink roller.
6-27
Detailed
Descriptions
The ink pump motor keeps the ink level normal by supplying ink when the level is
low.
DRUM
March 2006
Automatic Ink Supply for a New Drum
If the machine detects a new drum, ink is supplied automatically at the trial print for
the first job with this drum.
The machine detects a new drum if:
•
There is no master wrapped on the drum, and
•
The ink detection pins detect no ink
Mechanism:
1. The machine detects a new drum
↓
2. Ink is supplied automatically.
↓
3. If the machine detects the ink before 26 seconds, go to step 5.
If the machine does not detect the ink before 26 seconds, go to step 4.
↓
4. A blank master is wrapped around the drum, and the drum rotates, with pressure
applied to the drum. Then the blank master is removed. Go to step 5.
↓
5. Master making is started for the original that you set.
NOTE: There is also a manual ink supply procedure, like for previous machines.
“0” + “Economy Mode”
6-28
28 March 2006
DRUM
6.8.6 DETECTION OF MASTERS ON THE DRUM
[C]
[B]
[A]
C267D945.WMF
• The drum master sensor [A] detects whether there is a master on the drum.
• When there is a master on the drum, the black patch [B] is covered and the
sensor detects the light reflected from the master. When there is no master on
the drum, the black patch [B] is exposed. The black patch does not reflect light
back to the sensor. Because of this, the master eject process can be skipped
when a new master is being made, if no master is detected on the drum.
• There is a black patch [C] on the clamper. If a master covers this black patch,
there was an error during cutting, and because of this error the master is doublewrapped around the drum.
6-29
Detailed
Descriptions
[A]: Drum master sensor
[B]: Black patch on the screen
[C]: Black patch on the clamper
DRUM
March 2006
6.8.7 METAL SCREEN
C267D946.WMF
The flow of ink is shown above. The excess ink goes back to the inside of the drum
from the trailing edge of the metal screen.
[A]
C267D947.WMF
The adhesive parts [A] are only at the sides of the mylar seal for the metal screen.
They are not attached to the trailing edge. This prevents ink leakage from the
trailing edge.
[B]
C267D948.WMF
The leading edge of the mesh on the metal screen is reduced by 2.5 mm [B] from
previous models. This prevents small dots at the leading edge of the paper.
6-30
28 March 2006
DRUM
6.8.8 DRUM TYPE DETECTION
[B]
[A]
C267D957.WMF
Identify size 1
Identify size 2
Identify Color
The type of drum is distinguished by inserting jumper wires in the drum connector
[A] at three locations, as shown in the lower diagram.
Black drum
B4 drum
A4 drum
LG drum
Identify Color
No jumper
No jumper
No jumper
Identify size 1
Jumper inserted
Jumper inserted
No jumper
Identify size 2
Jumper inserted
No jumper
Jumper inserted
Identify Color
Identify size 1
Jumper inserted Jumper inserted
Jumper inserted Jumper inserted
Jumper inserted No jumper
Identify size 2
Jumper inserted
No jumper
Jumper inserted
Color drum
B4 drum
A4 drum
LG drum
NOTE: When you modify the color drum into a black drum, replace the ink holder
[B] to the correct type for a black drum. Then take off the jumper at the
‘identify color’ location. Never remove or insert jumpers at ‘identify size 1’
or ‘identify size 2’, or the machine will detect the incorrect drum size.
6-31
Detailed
Descriptions
C267D958.WMF
PAPER FEED
March 2006
6.9 PAPER FEED
6.9.1 OVERALL
[B]
[D]
[A]
[C]
C267D015.WMF
The top sheet of the paper on the paper table is first fed by the pick-up roller [A].
Then, it is separated by the paper feed roller [B] and the friction pad [C], and
transported to the registration rollers [D]. The upper and lower registration rollers
transport the sheet to the drum.
The paper feed roller is driven by the main motor, and an independent stepper
motor is used to control the registration roller. The registration roller synchronizes
the paper feed timing with the master on the drum. The registration roller starts
rotating after the paper has come into contact with the rollers and has been aligned.
6-32
28 March 2006
PAPER FEED
6.9.2 PAPER FEED MECHANISM
[D]
[B]
[A]
[E]
C267D949.WMF
[C]
During the printing cycle, when the feed start timing sensor [D] is actuated by the
actuator on the drum, the paper feed clutch [E] is energized to transmit the main
motor rotation to the paper feed roller shaft. The top sheet of the paper is
separated from the paper stack by the friction between the roller and the friction
pad, and transported to the registration roller.
A one-way clutch is installed in the paper feed roller so that after the
electromagnetic clutch is de-energized, it does not disturb the paper transportation.
6-33
Detailed
Descriptions
The pick-up roller [A] and paper feed roller [B] are driven by the main motor [C]
through gears and a timing belt.
PAPER FEED
March 2006
6.9.3 PAPER FEED/SEPARATION PRESSURE ADJUSTMENT
MECHANISM
[B]
[A]
[C]
Feeder
Thick paper Standard Thin paper
C267D003.WMF
[D]
[E]
[G]
[F]
C267D001.WMF
[A]: Normal position
[B]: Thick paper position
[C]: Thin paper position
• The user can change the pick-up roller pressure by changing the position of the
pressure adjustment lever [D].
• If paper feed jams frequently occur, the lever [D] should be moved to the left or
the right to adjust the pressure.
• If non-feed or multi-sheet feed problems still occur, the paper separation
pressure can also be adjusted by the lever [E].
• If there is still a paper feed problem, the technician can adjust the paper
separation pressure by loosening then moving the screw [F] up or down.
• For the Chinese model, the separation pressure adjustment lever [E] has 4 levels.
For the other models, a screw [G] is attached so that the lever [E] cannot move
down more than level 3.
6-34
28 March 2006
PAPER FEED
6.9.4 SIDE EDGE PAPER PRESS PLATE MECHANISM
[A]
C267D016.WMF
For some paper types, the side edges of the paper might curl up because the
centre of the paper is pressed down by the paper feed roller. This will cause paper
jams to occur.
Detailed
Descriptions
To prevent the curling up of the paper side edges, the paper guide plates [A] press
the edges down.
6-35
PAPER FEED
March 2006
6.9.5 REGISTRATION ROLLER MECHANISM
[B]
[A]
C267D017.WMF
Registration motor [A]
[C]
↓
Belt [B]
↓
Turns the lower registration roller [C]
NOTE: 1) The MPU controls the registration roller start timing to synchronize the
print paper with the image on the master on the drum.
2) The motor speed depends on the selected printing speed.
3) By pressing the image position keys on the operation panel, the
registration motor start timing is changed.
6.9.6 PAPER FEED RETRY MECHANISM
When paper is misfed at the paper feed tray, a paper feed jam is not displayed,
and the machine tries to feed the paper again.
The paper registration sensor does not turn on after the paper feed motor turns,
and the drum turns without paper. Then, when the feed start sensor is on again,
the paper feed motor starts to feed again.
The paper feed retry mechanism only operates during printing, and not for the trial
print.
The retry is done only one time. If paper is not fed, then a misfeed occurs.
6-36
28 March 2006
PAPER FEED
6.9.7 REGISTRATION ROLLER UP/DOWN MECHANISM
[B]
[D]
[A]
[C]
C267D950.WMF
Detailed
Descriptions
• After the printing paper is caught between the drum and the press roller, the
registration motor stops and the upper registration roller [A] is released from the
lower registration roller. This is to prevent interference from the registration
rollers while the drum and press roller transport the paper.
• When the high point of the cam [B] on the drum drive gear reaches the cam
follower [C], the shaft [D] rotates clockwise (as seen from the operation side) to
release the upper registration roller [A] from the lower registration roller.
6-37
PAPER FEED
March 2006
6.9.8 REGISTRATION SENSOR CLEANING
[A]
[B]
C267D018.WMF
NOTE: This mechanism is attached only for the Chinese model.
Dust on the registration sensor [A] can be removed by operating a lever [B]. The
technician should do this every visit.
6-38
28 March 2006
PAPER FEED
6.9.9 PRINTING PRESSURE MECHANISM
[C]
[A]
[D]
[B]
[E]
[H]
[A]
[G]
[F]
[I]
• When not in the printing cycle, the two solenoids [A] stay off and the stoppers [B]
lock the brackets [C] to keep the press roller [D] away from the drum.
• When the 1st sheet of paper is fed, the solenoid is energized but the brackets
are still locked by the stoppers due to strong tension from the springs [E].
• When the high points of the cams [G] on the front and rear drum flanges reach
the cam followers [F] on both sides of the press roller shaft, a small clearance is
made between the stoppers and the brackets. The two solenoids plungers are
pulled down at the same time, releasing the stoppers from the brackets.
• Printing pressure is applied by tension from the springs [E] when the cam
followers [F] come off the high points of the cams [G].
• During the printing cycle, the solenoids stay on. However, if paper does not
reach the registration sensor [H] at the proper time (when the cam follower is on
the high point of the cam), the solenoids are de-energized to lock the brackets.
• The printing pressure is released when the cams push down the cam followers
so that the press roller does not contact the master clamper [I].
• After printing is finished, the solenoids de-energize and the springs push the
stoppers back. Before the drum returns to the home position, the stoppers lock
the brackets again when the cams push down the cam followers.
6-39
Detailed
Descriptions
C267D951.WMF
PAPER FEED
March 2006
6.9.10 PAPER TABLE MECHANISM
[B]
[C]
[F]
[A]
[C]
[G]
C267D019.WMF
[E]
[I]
[D]
[H]
C267D002.WMF
Table Up and Down Mechanism
An independent dc motor, the paper table motor [A], drives the paper table. When
the motor turns, the pinions [B] turn on the racks [C], lifting up or lowering the paper
table.
There are two paper height sensors.
• Sensor 1 [E] is actuated when the top of the stack pushes the pick-up roller [D] to
a certain height.
• Sensor 2 [I] is actuated when the top of the stack pushes a feeler [H].
When the paper table moves up, the top of the paper stack contacts the pick-up
roller [D] or feeler [H], lifting it up. Then, when paper height sensor 1 [E] or 2 [I] is
actuated, the paper table stops.
During a printing run, sheets are fed from the stack, and the paper pick-up roller
and feeler both drop. When the paper height sensor 1 or 2 is de-actuated, the
paper table motor starts turning and lifts the paper table until the sensor is actuated
6-40
28 March 2006
PAPER FEED
again. In this way, the top of the paper stack remains at the same position during
printing.
When the tray lowers, the lower limit position is detected by the lower limit sensor
[F], which is beside the paper table motor.
When paper runs out, the paper feed table lowers, until the paper table lower limit
sensor (not shown) detects the lower limit position.
Why do we have two height sensors?
Note that the feeler [H] is at a different part of the stack from the pick-up roller [D].
Some types of paper have a different stack thickness at different parts of the stack.
This is notably true for envelopes, which have a greater stack thickness at the
leading edge. The pick-up roller contacts the stack a small distance away from the
leading edge, so the stack is a bit thicker than detected by an actuator attached to
the pick-up roller.
Then, if there is only one height sensor, it might detect that the table is at the
correct height at the wrong time, or that the stack height is too low at the wrong
time.
Then a misfeed will occur.
So, having two sensors prevents misfeeds.
Paper End Detection Mechanism
Paper Size Detection
NOTE: The paper size is not detected in this model, because there are no paper
size sensors. As a result, the master is always made at full size. (Also,
there is no size sensor for originals.)
6-41
Detailed
Descriptions
The paper end sensor [G] is under the paper table to detect when the paper on the
table runs out.
PAPER FEED
March 2006
6.9.11 PAPER TABLE SIDE FENCE MECHANISM
[B]
[C]
[A]
C267D952.WMF
The left and right side fences [A] move together due to a rack and pinion
mechanism. There is a lock lever [B] to hold the side fences in position.
NOTE: The lock lever may be useful if there is no dedicated operator and some of
the operators cannot set the side fences properly, causing paper feed
problems. Advise the operator to use the lock lever once the paper fences
are properly adjusted.
Paper Table Side-to-Side Shift Mechanism
The paper table shifting dial [C] shifts the image across the page. If the dial is
turned, the whole paper table moves towards one side or the other.
6-42
28 March 2006
PAPER FEED
Side Fence Friction Pads
[A]
C267D953.WMF
The user can install the friction pads if they are using thin paper.
6-43
Detailed
Descriptions
The two side fence friction pads are included as accessories. These are not used
normally, but if paper multi-feed frequently occurs, the friction pads [A] can be
installed to apply stopping pressure to the paper. These are especially useful when
thin paper is used.
PAPER DELIVERY
March 2006
6.10 PAPER DELIVERY
6.10.1 OVERALL
[B]
[A]
[D]
[E]
[C]
C267D902.WMF
Procedure
The exit pawl [A] and the air knife [B] separate the paper from the drum.
↓
The paper is fed to the paper delivery table [C] by the paper delivery unit [D].
↓
The paper exit sensor [E] is used for jam detection.
6-44
28 March 2006
PAPER DELIVERY
6.10.2 PAPER DELIVERY UNIT DRIVE MECHANISM
[A]
[D]
C267D021.WMF
[B]
[C]
Mechanism
NOTE: 1) The vacuum fan motor inside the unit holds the paper against the belts
[D] to deliver the paper to the delivery table.
2) Transport belt [D] become wider compare to previous Silver serious
machine.
3) The transport belt rotation speed depends on the selected print speed.
6-45
Detailed
Descriptions
Main motor [A]
↓
Belt and gear [B]
↓
Shaft [C]
↓
Rotates the transport belts [D].
PAPER DELIVERY
March 2006
6.10.3 PAPER SEPARATION FROM DRUM
[A]
C267D022.WMF
Air knife
• The air from the air knife fan motor [A] separates the paper from the drum.
• The air knife fan motor starts blowing air when the print start key is pressed or
when master cutting is finished. The paper passes under the exit pawl and is
delivered to the delivery table.
6-46
28 March 2006
PAPER DELIVERY
6.10.4 EXIT PAWL DRIVE MECHANISM
[B]
[C]
[A]
[D]
[E]
[G]
[F]
• During printing, the distance between the exit pawl [A] and the drum is very small,
to prevent paper wrap jams. However, when the master clamper [B] approaches
the exit pawl (as the drum turns), the pawl has to be moved away from the drum
to prevent it from being damaged by the master clamper. This is controlled by the
front drum flange [C], which is cam-shaped, and the cam follower [E] on the exit
pawl shaft.
• When the cam follower is not pushed out by the drum flange, the exit pawl
closely approaches the drum surface, due to the tension from a spring [G].
• As the master clamper approaches the exit pawl, the high point of the drum
flange cam [C] moves into contact with the cam follower [E] pushing it down. This
moves the cam follower arm [F] downwards. The pawl shaft turns clockwise to
move the pawl away from the drum.
6-47
Detailed
Descriptions
C267D023.WMF
PAPER DELIVERY
March 2006
C267D024.WMF
[D]
[F]
• When printing finishes and the printing pressure is released, the cam follower
arm [F] is engaged by the printing pressure release arm [D] and held in the lower
position. Therefore, after printing finishes, the cam follower is out of contact with
the cam, and the exit pawl moves away from the drum to its normal position.
6-48
28 March 2006
PAPER DELIVERY
6.10.5 SIDE PLATE GUIDE
[A]
C267D954.WMF
When printing on A4SEF, B5, and thin paper, side plate guides [A] should be
attached to the side plate of the paper delivery table. Users can attach these
guides.
Detailed
Descriptions
Then, the side plate guides can correctly stack the printouts on the paper delivery
table.
6-49
ABNORMAL VOLTAGE PROTECTION
28 March 2006
6.11 ABNORMAL VOLTAGE PROTECTION
This is for the AC220V ~240V machine only.
[A]
C267D955.WMF
There is an automatic detection system [A] for unexpected voltage surges,
featuring automatic shut-off and data logging features.
Momentary voltage drop
SP 1-83 records the number of momentary interruptions.
NOTE: The machine can record only interruptions of very short duration. If the
machine does not get voltage continuously, the PSU will shut off.
Low voltage (less than 150V)
Records (SP1-83) the number of low voltage peaks.
High voltage
Records (SP1-83) the number of high voltage peaks.
AC300V to 400V
The machine records the occurrence, and if the PSU keeps getting the high voltage
continuously, the main switch will shut off automatically to protect the machine.
Over voltage (More than AC400V)
The machine will shut off immediately after recording the high voltage occurrence.
NOTE: 1) The main switch contains a solenoid to shut off the main switch
automatically.
2) The auto shut off mode can be set ON or OFF by SP2-80.
3) A message will be displayed when the machine is turned on the first
time after an auto shut off.
6-50
28 March 2006
ABNORMAL VOLTAGE PROTECTION
General Notes on this Feature
Detailed
Descriptions
NOTE: 1) The durability of the PSU is improved compared to previous models.
2) The 100V machine does not have this mechanism, because voltages
more than 220 V will not occur.
3) The machine keeps a record, and you can check the data with SP 8-9
Data printout – Power failure. Refer to section 5-9-3.
4) Collect the logging data with the PSU board when it is needed for
investigation.
5) When the user turns the main power switch off, the machine detects this
as a ‘momentary voltage drop’ and a ‘low voltage’, and adds this to the
log for these two error types.
6-51
ERROR DETECTION
March 2006
6.12 ERROR DETECTION
6.12.1 MASTER EJECT JAM (E JAM LOCATION INDICATOR)
Picking up the used master from the drum
Check 1
Main Motor
Open
Open
Close
Clamper Motor
Close
700ms
700ms
Master Eject Motor
Master Eject Sensor
2nd Feed Timing Sn
Check 2
C267D903.WMF
Check 1:
The retry mechanism will turn on when the master eject sensor does not turn on
when the master eject motor is rotating.
Check 2:
The E jam indicator lights (master eject jam), when the master eject sensor does
not turn on between closing the clamper and turning on the 2nd feed timing sensor.
Compressing the used master
Pressure Plate
H.P. Sn.
Check
Pressure Plate
Limit Sn.
Pressure Plate
Motor
Master Eject
Sn.
C267D956.WMF
Check:
If the master eject sensor detects a master when the pressure plate limit sensor
turns on, the E jam indicator lights.
Just after turning on the main switch
Check:
If the master eject sensor is on (master detected), the E jam indicator lights.
6-52
28 March 2006
ERROR DETECTION
6.12.2 ADF JAM (P JAM LOCATION INDICATOR)
Feeding in the original (ADF)
Finish Scanning
Original Registration Sn
Original Feed Motor
Original feed Clutch
Feeding in
Feeding out
C267D904.WMF
Feeding in
The P jam indicator lights if the original registration sensor does not turn on within 5
seconds after the original feed motor turns on
Feeding out
Just after turning on the main switch
If the original registration sensor detects an original, the P jam indicator lights.
6-53
Detailed
Descriptions
When the scanner has fed out the correct length and feeds 150mm more, but the
original registration sensor still detects the original, the P jam indicator lights.
ERROR DETECTION
March 2006
6.12.3 MASTER FEED JAM (D JAM LOCATION INDICATOR)
Cutting the master
Master making
Retry Cut
Main Motor
Cutter H.P. Sn
Cutter H.P. Sn
Drum Master S.n.
Drum Master check
Cut error
C267D905.WMF
The drum master sensor does not turn on between feed start timing sensor and
drum black patch after the master cutting operation. In this case, the machine tries
to cut the master again and if the machine does not cut the master correctly, the D
jam indicator lights.
Clamping the master
Master Making
Wrapping Master
Mian Motor
Master Eject Position Sn
Drum Master Sensor
Drum Master check
C267D906.WMF
A master clamp error occurs when the drum master sensor does not turn on at the
home position (the drum stops at the home position for a short time; home position
is when the master eject position sensor turns on).
6-54
28 March 2006
ERROR DETECTION
6.12.4 PAPER FEED JAM (A JAM LOCATION INDICATOR + ! +
")
Paper feed
86°
Feed start timing sensor
Paper registration sensor
Registration check
C267D907.WMF
Paper feed will try again when the paper registration sensor does not turn on after
86 degrees from the paper start timing sensor. Then the drum will rotate one more
time and if the paper registration sensor still does not turn on, the A jam indicator
lights.
6.12.5 PAPER DELIVERY JAM (C JAM LOCATION INDICATOR)
Paper delivery
Detailed
Descriptions
33.58°
Master eject Position Sn
Paper Eject Sn
Paper exit check
C267D908.WMF
A paper exit error occurs when the paper exit sensor turns on immediately after
turning on the power or after finishing printing.
Also, a paper exit error occurs when the paper exit sensor turns on at 33.58
degrees from the paper ejection position during printing.
6-55
TIMING CHART
March 2006
6.13 TIMING CHART
6.13.1 SCANNING
Start Making
Master
Check HP
Master
Eject
Scan
Check HP
Scanning
Scanner Motor
Scanner HP Sn
Xenon lamp
C267D909.WMF
6.13.2 MASTER EJECT
Finish
Scanning
Master Eject
Open & Close Clamper
Eject Master
Master
Feed
Main Motor
Master Eject Position Sn
Feed Start Timing Sn
Clamper Motor
Clamper Open Sn
Clamper Close Sn
Master Eject Motor
C267D910.WMF
6-56
6-57
Cutter Motor
Cutter HP Switch
Master Feed Motor
Clamper Open Sn
Clamper Close Sn
Clamper Motor
Feed Start
Timing Sn
Master Eject
Position Sn
Main Motor
Detailed
Descriptions
Send Master to Clamper
Finished Master Eject
Wrapping Master on the Drum
Master Feed
Master Cut
Trial
Print
28 March 2006
TIMING CHART
6.13.3 MASTER FEED
C267D912.WMF
TIMING CHART
March 2006
6.13.4 PRINT
C267D911.WMF
6-58
28 March 2006
ESSENTIAL DIFFERENCES BETWEEN C248 AND C267 MODELS
7. SPECIFICATIONS
No.
Item
1
Scanner unit
2
Operation panel
3
Master eject unit
4
Master making unit
5
Drum unit
6
Separation Pressure
7
8
Paper height sensor
Paper delivery unit
9
PSU
10
MPU
11
12
13
14
Image processing
SP mode / User tools
Auto off mode
ADF
Remarks
A newly designed scanner unit is used.
600 dpi x 300 dpi CCD
A3 / 11” x 17” size book scanner
A newly designed operation panel is used.
Bigger size bright LCD
Two start buttons (master making and print) combined
into one.
Based on the TT model and added a master eject unit
open mechanism like in the VT series.
Based on the TT model and added a master making
unit slide-out mechanism like in the Sapphire series
Based on the TT model
New ink pump unit
Trochoid type pump
Metal screen / Cloth screen
Change the mylars to prevent ink leakage
The separation pressure can be changed with a lever.
3 levels (Other destinations)
4 levels (Chinese models)
Two paper height sensors
Based on the TT model
The main motor drives the paper delivery unit.
Vacuum fan changed from sirocco fan motor to axial
fan motor.
A newly designed PSU is used.
Abnormal voltage protection mechanism. (220V
machine only)
• Durability is improved
• Auto detection system for unexpected voltage
surges, with automatic shut-off and data logging
features.
A newly designed MPU is used.
MPU controls: Machine, paper feed, image processing,
main motor
Upgrade the firmware using a flash memory card
An LSI (same as the HP4) improves image processing
Based on the HP4
Added the auto-off mode
A newly designed ADF is used.
7-1
Spec.
7.1 ESSENTIAL DIFFERENCES BETWEEN C248 AND
C267 MODELS
ESSENTIAL DIFFERENCES BETWEEN C252 AND C267 MODELS
28 March 2006
7.2 ESSENTIAL DIFFERENCES BETWEEN C252 AND
C267 MODELS
No.
Item
1
Scanner unit
2
Operation panel
3
4
Master eject unit
Master making unit
5
Drum unit
6
7
8
Paper table
Paper height sensor
Paper feed
9
Separation pressure
10
PSU
11
MPU
12
13
13
14
15
Image processing
Printing speed
SP mode / User tools
Auto off mode
ADF
Remarks
A newly designed scanner unit is used.
600 dpi x 300 dpi CCD
A3 / 11” x 17” size book scanner
A newly designed operation panel is used.
Bigger size bright LCD
Two start buttons (master making and print) combined
into one.
Master eject unit open mechanism like in the VT series
Master making unit slide-out mechanism like in the
Sapphire series
Ink pump unit
New ink pump unit
Changed the motor to Trochoid type from piston pump
type
Based on the Silver series paper feed table
Two paper height sensors
Two types of roller (Paper pick-up roller and paper feed
roller)
The number of levels for paper feed pressure are
changed from 2 levels to 3 levels.
The separation pressure can be changed by the user
with a lever.
3 levels (Other destinations)
4 levels (Chinese models)
A newly designed PSU is used.
Abnormal voltage protection mechanism. (220V
machine only)
• Durability is improved
• Auto detection system for unexpected voltage
surges, with automatic shut-off and data logging
features
A newly designed MPU is used.
MPU controls: Machine, paper feed, image processing,
main motor
Upgrade the firmware using a flash memory card
An LSI (same as the HP4) improves image processing
There are three printing speeds (not two).
Based on the HP4
Added the auto-off mode
A newly designed ADF is used.
7-2
28 March 2006
GENERAL SPECIFICATIONS
7.3 GENERAL SPECIFICATIONS
Desktop
300 dpi × 300 dpi
Pixel Density
In Fine mode, 400 dpi in sub-scanning resolution
600 dpi × 300 dpi CCD
Scanning
This model always reduces the amount of scanned data in
the main-scan direction by half before printing.
Master Process
Digital with 300 dpi thermal head
Original Type
Sheet / Book
Printing Process
Fully automatic one-drum system
Platen Mode
Maximum A3 / DL size
ADF Mode
Original Size
Maximum 297 mm × 432 mm, 11.7” × 17.0”
Minimum 105 mm × 128 mm, 4.1” × 5.0”
Platen Mode
Maximum 30 mm
Original Thickness / Weight
ADF Mode
52 to 105 g/m2, 14 to 28 lb.
40 sheets (A4/ 8 1/2” and below size, 80 g/m2 [20 lb.])
Original Stack Capacity (ADF)
30 sheets (Over A4/ 8 1/2” x 11” size, 80 g/m2 [20 lb.])
Maximum 275 mm × 395 mm, 10.8” × 15.6”
Copy Paper Size
Minimum 90 mm × 140 mm, 3.5” × 4.7”
China model
35 to 127.9 g/m2
Copy Paper Weight
Other models
47.1 to 209.3 g/m2
Printing Speed
80, 100, 130 cpm (3 steps)
Original Type
Text, Text/Photo, Photo, Pale mode
Master Making Density
Lighter, Normal, Darker 1, Darker 2
Metric (%): 141, 122, 115, 93, 87, 82, 71
Reproduction Ratios
Inch (%): 155, 129, 121, 93, 77, 74, 65
Master Eject Box Capacity
30 masters
Copy Paper Capacity
1,000 sheets (64 g/m2, 171 lb.)
Paper Delivery Tray Capacity 1,000 sheets (64 g/m2, 171 lb.)
120 V, 60 Hz, 2.0 A
Power Source
220 V – 240 V, 50 – 60 Hz, 1.1 A
Power Consumption
Less than 180 W
Sound Power Level
Standby: 36 dB
Copying 80 cpm: 78 dB
Copying 100 cpm: 80 dB
Copying 130 cpm: 84 dB
Noise Emission
Operating Position Sound Power Level
Standby: 20 dB
Copying 80 cpm: 63 dB
Copying 100 cpm: 70 dB
Copying 130 cpm: 72 dB
7-3
Spec.
Configuration
GENERAL SPECIFICATIONS
Dimensions (W × D × H)
Weight
Master Processing Time
First Print Time
Printing Area
Leading Edge Margin
Side / Vertical Registration
Adjustable Range
28 March 2006
Stored
750 × 676 × 633 mm, 29.5” × 26.6” × 24.9”
Stored with ADF
750 × 676 × 686 mm, 29.5” × 26.6” × 27.0”
Set up
1224 × 676 × 633 mm, 48.2” × 26.6” × 24.9”
Set up with ADF
1224 × 676 × 686 mm, 48.2” × 26.6” × 27.0”
68.5 kg
32 seconds (A4 )
When setting an original on the exposure glass
33 seconds (A4 )
When setting an original on the exposure glass
B4 Drum
250 mm × 355 mm
LG Drum
210 mm × 355 mm
A4 Drum
210 mm × 288 mm
5 mm ± 3 mm
± 10 mm
Master Type
Master
Yield
Maximum run length per master
Storage Condition
Storage Period
Ink Type
Ink
Available Colors
Storage Condition
Storage Period
280 mm width (B4)
240 mm width (LG / A4)
100 mm / roll (China)
125 mm / roll (other destinations)
260 masters / roll (B4 / LG)
300 masters / roll (A4)
205 masters / roll (B4 China)
2000 prints / master
0 to 40 C, 10 to 95 %RH
12 months after production date
500 ml / pack (Black, China)
600 ml / pack (Black, Other destinations)
600 ml / pack (Other colors)
Black, Red, Blue, Green, Brown, Violet
Yellow, Maroon, Navy, Orange, Hunter green
-5 to 40 C, 10 to 95 %RH
-5 to 40 C (12 months after production date)
15 to 25 C (18 months after production date)
Avoid locations exposed to direct sunlight.
7-4