AOC | 7KLR | User`s manual | AOC 7KLR User`s manual

AOC 7KLR
AOC 7KLR
17 inch Color Monitor
User’s
Manual
by Envision Peripherals, Inc.
www.aocmonitor.com
Before operating your monitor, please read this
manual thoroughly.
AOC 7KLR
1
v2_123102
For Your Safety
AOC 7KLR
FCC Statement
Notice
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses and
can radiate radio frequency energy, and if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try
to correct the interference by one or more of the
following measures:
1. The changes or modifications not expressly
approved by the party responsible for
compliance could void the user's authority to
operate the equipment.
2. Shielded interface cables and AC power cord, if
any, must be used in order to comply with the
emission limits.
3. The manufacturer is not responsible for any
radio or TV interference caused by unauthorized
modification to this equipment. It is the
responsibility of the user to correct such
interference.
As an ENERGY STAR® Partner, Envision
Peripherals, Inc. has determined that this product
meets the ENERGY STAR® guidelines for energy
efficiency.
1. Reorient or relocate the receiving antenna.
Warning
2. Increase the separation between the equipment
and receiver.
To prevent fire or shock hazard, do not expose the
monitor to rain or moisture. Dangerously high
voltage is present inside the monitor. Do not open
the cabinet. Refer servicing to qualified personnel
only.
3. Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio/TV
technician for help.
AOC 7KLR
2
v2_123102
For Your Safety
Precautions
• The monitor is equipped with a three-pronged
grounded plug, a plug with a third (grounding)
pin. As a safety feature, this plug will only fit into
a grounded power outlet. If your outlet does not
accommodate the three-wire plug, have an
electrician install the correct outlet, or use an
adapter to ground the appliance safely. Do not
defeat the safety purpose of the grounded plug.
• Do not use the monitor near water, e.g. near a
bathtub, washbowl, kitchen sink, laundry tub,
swimming pool or in a wet basement.
• Do not place the monitor on an unstable cart,
stand, or table. If the monitor falls, it can injure a
person and cause serious damage to the
appliance. Use only a cart or stand
recommended by the manufacturer or sold with
the monitor. If you mount the monitor on a wall
or shelf, use a mounting kit approved by the
manufacturer and follow the kit instructions.
• Unplug the unit during a lightning storm or when
it will not be used for long periods of time.
This will protect the monitor from damage due to
power surges.
• Do not overload power strips and extension
cords. Overloading can result in fire or electric
shock.
• Slots and openings in the back and bottom of
the cabinet are provided for ventilation. To
ensure reliable operation of the monitor and to
protect it from overheating, be sure these
openings are not blocked or covered. Do not
place the monitor on a bed, sofa, rug, or similar
surface. Do not place the monitor near or over a
radiator or heat register. Do not place the
monitor in a bookcase or cabinet unless proper
ventilation is provided.
• Never push any object into the slot on the
monitor cabinet. It could short circuit parts
causing a fire or electric shock. Never spill
liquids on the monitor.
• Do not attempt to service the monitor yourself;
opening or removing covers can expose you to
dangerous voltage and other hazards. Please
refer all servicing to qualified service personnel.
• The monitor should be operated only with the
type of power source indicated on the label. If
you are not sure of the type of power supplied to
your home, consult your dealer or local power
company.
• To ensure satisfactory operation, use the
monitor only with UL-listed computers which
have appropriately configured receptacles
marked between 100 - 240 V AC, Min. 3.5A.
• Disconnect the power cord to stop the power
supply to the monitor.
AOC 7KLR
AOC 7KLR
• The wall socket should be installed near the
equipment and should be easily accessible.
3
v2_123102
For Your Safety
General Notes
General Features:
• Do not install the monitor near heat sources
such as radiators or air ducts.
• 17" (43.2 cm) Color Monitor
AOC 7KLR
• Crisp, Clear Display for Windows
• Do not place monitor in direct sunlight or in
areas with excessive dust, mechanical vibration
or shock.
• Supports Resolutions up to 1600 X 1200 pixels
@75Hz
• EPA ENERGY STAR®
• Save the original shipping carton and packing
materials in case you need to ship your monitor.
Be sure to repackage your monitor as it was
originally packed at the factory.
Package Contents
• Periodically clean your monitor with a soft cloth.
Stubborn stains may be removed with a cloth
lightly dampened with a mild detergent solution.
Never use strong solvents such as thinners,
benzene, or abrasive cleaners, since these
will damage the cabinet. Always unplug the
monitor before cleaning it.
The box that your monitor was shipped in should
have included the following items:
1. Color Monitor
2. Power Cord
3. Quick Start Guide
4. Booklet
(containing Warranty and Safety information)
Using the Right Power Cord
The supplied power cord is a NEMA 5-15 style
plug. It is UL-listed and CSA labeled for
125 volts AC.
If the monitor will be connected to your computer’s
power outlet, use a minimum No. 18 AWG, type
SJT or SVT three conductors cord with one end
terminating with a male grounded plug, rated 10A,
250V, CEE-22. The other end must terminate with
a molded-on type connector body, rated 10A,
250V, having standard CEE-22 female
configuration.
AOC 7KLR
4
v2_123102
Before You Operate the Monitor
AOC 7KLR
Installing & Removing the Base
AOC 7KLR
5
v2_123102
Before You Operate the Monitor
AOC 7KLR
Connecting the Wires Using the Power Cord Supplied
Caution: Make sure the power cord is the correct
type that is required in your area. This monitor
has a universal power supply that allows
operation in either 100/120V AC or 220/240V AC
voltage areas (no user adjustment is required).
1. Connect the built-in video cable into the 15-pin
connector on the back of your computer and
tighten the two screws.
2. Connect the power cord into your monitor's
power input socket.
If the AC outlet is not grounded (with three
holes), install the proper grounding adapter (not
supplied).
3. Plug the other end of the power cord into a
grounded AC outlet or UL-approved power strip.
AOC 7KLR
6
v2_123102
Before You Operate the Monitor
AOC 7KLR
Connecting the Wires Using An Optional Power Cord (Not Supplied)
Follow these steps:
The power cord supplied with your monitor can
only be connected to a grounded electrical wall
socket or power strip.
1. Connect the built-in video cable into the 15-pin
connector on the back of your computer and
tighten the two screws.
If you wish to connect your monitor to a power
supply using the power input socket on the back of
your computer, you must purchase a power cord
with CEE-22 terminated connectors (see
illustration above).
AOC 7KLR
2. Connect the power cord into your monitor's
power input socket.
3. Plug the other end of the power cord into the
power output socket on your PC.
7
v2_123102
Operating Instructions
AOC 7KLR
Front Panel Buttons
Power: Press this button to put the monitor
into Off mode. The power indicator will turn
orange. Press and hold this button again to
restore the monitor to normal operation
mode.
Shuttle Knob: Press this knob to open the
OSD window or select a highlighted function.
Rotate this knob to switch functions or adjust
settings.
Power Indicator: A green light indicates that
the monitor is on. An orange light indicates
that the monitor is in Off mode.
On-screen Display (OSD): Press the
Shuttle Knob to open the OSD window
and adjust settings on your monitor.
Note: This monitor automatically turns on
when it is plugged into an AC outlet.
AOC 7KLR
(See next page.)
8
v2_123102
Operating Instructions
AOC 7KLR
Adjusting the OSD Settings
1. Press the Shuttle Knob to open the OSD
window.
5. To save and exit, select the exit function or
leave the monitor alone for 10 seconds. If you
want to adjust any other function, repeat steps
2-4.
2. Rotate the Shuttle Knob until the desired
function is highlighted.
Note: When the OSD window is open, the input
signal timing settings appear at the top.
H: stands for horizontal frequency and
V: stands for vertical frequency.
3. Press the Shuttle Knob again to open the
function’s window.
4. Rotate the Shuttle Knob to change the settings
of the function.
AOC 7KLR
9
v2_123102
Operating Instructions
AOC 7KLR
Plug & Play DDC1/2B Feature
Windows INF Driver File
This monitor is equipped with VESA DDC1/2B
capabilities according to the VESA DDC
STANDARD. It allows the monitor to inform the
host system of its identity and, depending on the
level of DDC used, communicate additional
information about its display capabilities. The
communication channel is defined in two levels,
DDC1 and DDC2B.
Most computers will automatically configure your
monitor to work with your computer. For optimal
viewing of your monitor, download the AOC
monitor driver.
The DDC1 is a unidirectional data channel from the
display to the host that continuously transmits
EDID information. The DDC2B is a bidirectional
data channel based on the I²C protocol. The host
can request EDID information over the DDC2B.
AOC 7KLR
Follow these steps:
1. Go to www.aocmonitor.com
2. Click on SUPPORT to open the drivers web
page.
3. Follow the directions on the web page to
download and install the driver on your
computer.
Or go to www.aocmonitor.com/driver.html to
directly access the driver web page.
10
v2_123102
Technical Support (FAQ)
Problem
AOC 7KLR
Possible Solution
Power LED is not ON
• Make sure the power cord is properly connected to a grounded power outlet
and to the monitor.
No Plug & Play
•
•
•
•
Picture is fuzzy
• Adjust the Contrast and Brightness settings.
Picture bounces or a
wave pattern is
present in the picture
• Move electrical devices away from the monitor. They may be causing electrical
interference.
Power LED is ON
(green or orange light
is ON) but there is no
video or picture.
•
•
•
•
Missing one of the
primary colors (RED,
GREEN, or BLUE)
• Inspect the video cable and make sure that none of the pins are bent.
• Make sure the video cable is properly connected to the computer.
Screen image is not
centered or sized
properly
• Adjust the Horizontal, Vertical or Zoom settings in the OSD window.
Picture has color
defects (white doesn’t
look white)
• Adjust the User Color setting in the OSD window.
AOC 7KLR
Confirm that your computer is Plug & Play compatible.
Confirm that your video card is Plug & Play compatible.
Inspect the video cable and make sure that none of the pins are bent.
Make sure the AOC monitor drivers are installed
(AOC monitor drivers are available at: www.aocmonitor.com)
Press a key on the keyboard or wiggle the mouse to re-activate the monitor.
Make sure the video cable is properly connected to the computer.
Inspect the video cable and make sure none of the pins are bent.
Make sure your computer is operating correctly by pressing the CAPS LOCK
key and observing whether the CAPS LOCK light turns ON or OFF.
11
v2_123102
Appendix
AOC 7KLR
Specifications
CRT
Size
Input
17.0" (43.2 cm)
11.4” (29 mm) neck
0.21mm(H),
0.25mm(D) dot
pitch
90 degree
deflection
Viewable image size
16.0” (40.6 cm)
diagonal
Preset Display area
11.8” (300 mm) X
9.1” (230 mm)
Dot Clock
200 MHz
Maximum Resolution
1600 x 1200 pixels
Plug & Play
VESA DDC1/2B
TM
AOC 7KLR
12
Video
Red, Green, Blue
Analog Interface
Separate
Sync.
H/V TTL
H/V Sync.
Positive/Negative
H-Frequency
30 kHz - 95 kHz
V-Frequency
50 Hz -160 Hz
Input
Video
Signal
Analog:
0.7 Vpp,
75 OHM, Positive
Power Source
Universal AC
100 - 240 V
50/60 Hz
Factory Preset Mode
8
User Programmable Mode
20
EPA ENERGY STAR®
Yes
Power Consumption
(Maximum)
120 Watts
Regulatory
Compliance
UL, CSA, FDA,
FCC, TÜV/GS,
TCO92
v2_123102
Appendix
AOC 7KLR
Specifications (continued)
Environmental
Considerations
Operating Temp:
32° to 104°F
(0° to 40°C) ambient
Operating Humidity:
10% to 85% relative,
non-condensing
Signal Cable
Attached Mini D-sub
15 Male
Optimal Viewing Mode: 1024 x 768 x 85 Hz
AOC 7KLR
13
v2_123102
Appendix
AOC 7KLR
Factory Preset Timing Table
Standard
VGA
VESA / 85
VESA / 75
AOC 7KLR
Resolution
(in pixels)
Horizontal
Frequency
Vertical
Frequency
720 × 400
31.5 kHz
70 Hz
640 × 480
31.5 kHz
60 Hz
640 × 480
43.3 kHz
85 Hz
800 × 600
53.7 kHz
85 Hz
1024 × 768
68.7 kHz
85 Hz
1280 × 960
85.9 kHz
85 Hz
1280 × 1024
91.1 kHz
85 Hz
1600 × 1200
93.8 kHz
75 Hz
14
v2_123102
Appendix
AOC 7KLR
Connector Pin Assignment
Pin Number
AOC 7KLR
Description
Pin Number
Description
1
Red
9
NC
2
Green
10
Ground
3
Blue
11
Monitor Ground
4
Ground
12
DDC-Serial Data
5
Ground
13
H-Sync
6
R-Ground
14
V-Sync / *V-Clk
7
G-Ground
15
DDC-Serial Clock
8
B-Ground
*
For DDC
15
v2_123102
Limited 3-Year Warranty
This is a warranty statement for AOC color
monitors including those sold within North America
as specified.
Envision Peripherals, Inc. (EPI) warrants this
product to be free from defects in material and
workmanship for a period of three (3) years after
the original date of consumer purchase. During this
period, EPI will, at its option, either repair the
defective product with new or rebuilt parts, or
replace it with a new or rebuilt product at no charge
except as stated below*. The parts or product that
are replaced become the property of EPI.
* This limited warranty does not cover any losses
or damages that occur as a result of:
• Shipping or improper installation or
maintenance
• Misuse
• Neglect
• Any cause other than ordinary commercial or
industrial application
• Adjustment by non-authorized source
• Repair, modification, or installation of options or
parts by anyone other than an EPI Authorized
Service Center
•
Improper environment
AOC 7KLR
AOC 7KLR
• Excessive or inadequate heating or air
conditioning or electrical power failures, surges,
or other irregularities. This three-year limited
warranty does not cover any of the product's
firmware or hardware that you or any third party
have modified or altered; you bear the sole
responsibility and liability for any such
modification or alteration.
All express and implied warranties for the product
(including the warranties of merchantability and
fitness for a particular purpose) are limited in
duration to a period of three (3) years for parts and
labor from the original date of consumer purchase.
No warranties (either expressed or implied) apply
after this period. In the United States, some states
do not allow limitations on how long an implied
warranty lasts. Therefore, the above limitations
may not apply to you.
EPI’s obligations and your remedies hereunder are
solely and exclusively as stated here. EPI’s liability,
whether based on contract, tort, warranty, strict
liability, or other theory, shall not exceed the price
of the individual unit whose defect or damage is the
basis of the claim. In no event shall EPI be liable
for any loss of profits, loss of use or facilities or
equipment or other indirect, incidental, or
consequential damage. In the United States, some
states do not allow the exclusion or limitation of
incidental or consequential damages. Therefore,
the above limitations may not apply to you.
16
v2_123102
Warranty (continued)
Although this limited warranty gives you specific
legal rights, you may have other rights which may
vary from state to state.
In the United States of America, this limited
warranty is only valid for products purchased in the
Continental United States, Alaska, and Hawaii.
Outside the United States, this limited warranty is
only valid for products purchased in Canada.
In the United States, to obtain service under this
limited warranty:
AOC 7KLR
EPI is not responsible for damage to inbound
products that were not properly packaged.
EPI will pay the return shipment charges within one
of the countries specified within this warranty
statement. EPI is not responsible for any costs
associated with the transportation of products
across international borders. This includes the
international borders of the countries within this
warranty statements.
© 2001 Envision Peripherals, Inc.
1. Call EPI’s Customer Service, RMA Department
at the toll free number (800) 343-5777 for the
nearest Authorized Service Center located in
your area.
2. Ask for a Return Merchandise Authorization
(RMA) number.
3. Deliver the product freight pre-paid to the EPI
Authorized Service Center.
If you cannot deliver the product in person:
•
Pack it in its original shipping container
(or equivalent)
•
Put the RMA number on the shipping carton
• Insure it (or assume the risk of loss / damage
during shipment)
• Pay one-way shipping charge
AOC 7KLR
17
v2_123102
Download PDF