DEWETRON DEWE-3300 Technical Reference Manual

DEWE-3300
TECHNICAL
REFERENCE
MANUAL
WELCOME TO
THE WORLD OF
DEWETRON!
ISO9001
EN ISO 14001
Congratulations on your new device! It
will supply you with accurate, complete
and reproducible measurement results
for your decision making.
Look forward to the easy handling and
the flexible and modular use of your
DEWETRON product and draw upon
more than 25 years of DEWETRON
expertise in measurement engineering.
CUSTOMIZED
MODULAR
COMPETENT
COMMITTED
APPROVED
Copyright © DEWETRON GmbH
This document contains information which is protected by copyright. All rights are reserved. Reproduction,
adaptation, or translation without prior written permission is prohibited, except as allowed under the copyright
laws.
All trademarks and registered trademarks are acknowledged to be the property of their owners.
DEWESoft™ is a trademark of Dewesoft d.o.o
PREFACE
Thank you!
Thank you very much for your investment in DEWETRON's unique data acquisition systems. These are top-quality
instruments which are designed to provide you years of reliable service. This guide has been prepared to help you
get the most from your investment, starting from the day you take it out of the box, and extending for years into the
future.
This guide includes important startup notes, as well as safety notes and information about keeping your DEWETRON
system in good working condition over time.
We strongly suggest that you read this entire manual, especially the safety and care sections, as well as to avoid
damaging your DEWETRON system.
What is the DEWE-3300?
This product is used for measuring of different physical and/or electrical sizes (depending on model or configuration). The connection is depending on model or configuration and takes place via safety banana plugs, BNC connectors (± 50V max.), D-SUB connectors (± 50V max.), thermocouple connectors (± 50V max.), BINDER®
connectors (± 50V max.), SMB connetcors (± 50V max.), µdot connectors (± 50V max.), LEMO® connectors or RJ-45
connectors.
DEWE-3300 • Technical Reference Manual • Printing version 1.0.4 • August 29, 2017
3
PREFACE
Notes
4
TABLE OF CONTENT
Content
General Information, Safety Instructions
7
Training………………………………………………………………………………………………………………………………… 7
Calibration…………………………………………………………………………………………………………………………… 7
Support………………………………………………………………………………………………………………………………… 7
Service/repairs……………………………………………………………………………………………………………………… 7
Warranty Information…………………………………………………………………………………………………………… 8
Printing History……………………………………………………………………………………………………………………… 8
Safety conventions………………………………………………………………………………………………………………… 9
General safety and hazard warnings for all DEWETRON systems…………………………………………… 10
Maintenance………………………………………………………………………………………………………………………… 13
Windows updates and antivirus/security software………………………………………………………………… 14
Problematic network stacks…………………………………………………………………………………………………… 14
Environmental Considerations……………………………………………………………………………………………… 14
Main System
15
DEWE-3300 - All-in-one standard instrument………………………………………………………………………… 15
System specifications…………………………………………………………………………………………………………… 15
Base models………………………………………………………………………………………………………………………… 16
Dimensions…………………………………………………………………………………………………………………………… 16
DEWE-330x at a glance………………………………………………………………………………………………………… 17
Possible configurations and panel options…………………………………………………………………………… 22
Power supply………………………………………………………………………………………………………………………… 23
A/D Conversion
A1
Internal Wiring
B1
CE-Certificate of conformity
C1
DEWE-3300 • Technical Reference Manual • Printing version 1.0.4 • August 29, 2017
5
TABLE OF CONTENT
Notes
6
General Information, Safety Instructions
SERVICES
Training
DEWETRON offers training at various offices around the world several times each year. DEWETRON headquaters
in Austria have a very large and professional conference and seminar center, where training classes are conducted
on a regular basis starting with sensors and signal conditioning, A/D technology and software operation. For more
information about training services, please visit:
http://www.dewetron.com/en/services/dewetron-academy.php
Dewetron Inc. in the USA also has a dedicated training facility connected to its headquarters, located in Rhode Island.
For more information about training services in the US, please visit:
http://www.dewamerica.com/support/trainingclasses
Calibration
Every instrument needs to be calibrated at regular intervals. The standard norm across nearly every industry is
annual calibration. Before your DEWETRON data acquisition system is delivered, it is calibrated at our DEWETRON
headquater. Each of this system is delivered with a certificate of compliance with our published specifications.
Detailed calibration reports from our calibration system are available for purchase with each order. We retain them
for at least one year, so calibration reports can be purchased for up to one year after your system was delivered.
Support
DEWETRON has a team of people ready to assist you if you have any questions or any technical difficulties regarding
the system. For any support please contact your local distributor first or DEWETRON directly.
For Asia and Europe, please contact:
For the Americas, please contact:
DEWETRON GmbH
Parkring 4
8074 Grambach
AUSTRIA
Tel.:
+43 316 3070
Fax:
+43 316 307090
Email: [email protected]
Web: http://www.dewetron.com
DEWETRON, Inc.
2850 South County Trail, Unit 1
East Greenwich, RI 02818
U.S.A.
Tel.:
+1 401 284 3750
Toll-free: +1 866 598 3393
Fax:
+1 401 284 3755
Email:
[email protected]
Web:
http://www.dewamerica.com
The telephone hotline is available
Monday to Friday between
08:00 and 17:00 CET (GMT +1:00)
The telephone hotline is available
Monday to Friday between
08:00 and 4:30 EST
Service/repairs
Only the team of DEWETRON is allowed to perform any kinds of repairs to your system to assure a safe and proper
operation in future. For information regarding service and repairs please contact your local distributor first or
DEWETRON directly.
!
Any spare parts (screws, backplanes, cables,...) must be obtained from DEWETRON only.
DEWE-3300 • Technical Reference Manual • Printing version 1.0.4 • August 29, 2017
7
NOTICE
The information contained in this document is subject to change without notice.
DEWETRON GmbH (DEWETRON) shall not be liable for any errors contained in this document. DEWETRON MAKES
NO WARRANTIES OF ANY KIND WITH REGARD TO THIS DOCUMENT, WHETHER EXPRESS OR IMPLIED. DEWETRON
SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. DEWETRON shall not be liable for any direct, indirect, special, incidental, or consequential damages,
whether based on contract, tort, or any other legal theory, in connection with the furnishing of this document or the
use of the information in this document.
Warranty Information
A copy of the specific warranty terms applicable to your DEWETRON product and replacement parts can be obtained
from your local sales and service office.
Restricted Rights Legend
Use austrian law for duplication or disclosure.
DEWETRON GmbH
Parkring 4
A-8074 Grambach / Austria
TRION™ is a trademark of DEWETRON GmbH.
Any other trademarks and registered trademarks are acknowledged to be the property of their owners.
Printing History
Please refer to the page bottom for printing version.
Copyright © DEWETRON GmbH.
This document contains information which is protected by copyright. All rights are reserved. Reproduction,
adaptation, or translation without prior written permission is prohibited, except as allowed under the copyright laws.
8
SAFETY CONVENTIONS
Safety conventions
Observe precautions for handling electrostatic sensitive devices!
!
This icon denotes a caution, which advises you of precautions to take to avoid injury, data
loss, or a system crash. When this symbol is marked on the product, refer to the technical
reference manual.
Indicates hazardous voltages.
Indicates the chassis terminal
WARNING
Calls attention to a procedure, practice, or condition that could cause bodily
injury or death.
CAUTION
Calls attention to a procedure, practice, or condition that could possibly cause
damage to equipment or permanent loss of data.
WARNINGS
The following general safety precautions must be observed during all phases of operation, service, and
repair of this product. Failure to comply with these precautions or with specific warnings elsewhere in this
manual violates safety standards of design, manufacture, and intended use of the product. DEWETRON
GmbH assumes no liability for the customer’s failure to comply with these requirements.
DEWE-3300 • Technical Reference Manual • Printing version 1.0.4 • August 29, 2017
9
SAFETY INSTRUCTIONS
Your safety is our primary concern! Please be safe!
!
General safety and hazard warnings for all DEWETRON systems
>> Use this system under the terms of the specifications only to avoid any possible danger. If the unit is used
in a manner not specified by the manufacturer the protection can be impaired!
>> Ths product is intended for use in industrial locations. As a result, this product may cause interference if used in residential areas. Such use must be avoided unless the user takes special measures to reduce
electromagnetic emissions to prevent interferences to the reception of radio and television broadcasts.
>> Maintenance will be executed by qualified staff only.
>> During the use of the system, it might be possible to access another parts of a more comprehensive system. Please read and follow the safety instructions provided in the manuals of all other components regarding warning and security advices for using the system.
>> With this product, only use the power cable delivered or defined for the host country.
>> DO NOT connect or disconnect sensors, probes or test leads, as these parts are connected to a voltage supply unit.
>> The system is grounded via a protective conductor in the power supply cord. To avoid electric shocks, the protective conductor has to be connected with the ground of the power network. Before connecting the input
or output connectors of the system, make sure that there is a proper grounding to guarantee
potential free usage. For countries, in which there is no proper grounding, please refere to your local legally safety regulations for safety use.
DC systems: Every DC system has a grounding connected to the chassis (yellow/green safety banana plug).
>> Please note the characteristics and indicators on the system to avoid fire or electric shocks. Before connecting the system, please carefully read the corresponding specifications in the product manual.
>> The inputs are not, unless otherwise noted (CATx identification), for connecting to the main circuits of category II, III and IV. The measurement category can be adjusted depending on module configuration.
>> The power cord separates the system from the power supply. Do not block the power cord, since it has to be accessible for the users.
>> Supply overvoltage category is II.
>> DO NOT use the system if equipment covers or shields are removed.
>> If you assume the system is damaged, get it examined by authorised personnel only.
>> Any use in wet rooms, outdoors or in adverse environmental condition is not allowed!
Adverse environmental conditions are:
> Moisture or high humidity
> Dust, flammable gases, fumes or dissolver
> Thunderstorm or thunderstorm conditions (except assembly PNA)
> Electrostatic fields, et cetera.
>> Any direct voltage output is protected with a fuse against short cut and reverse-polarity, but is NOT galvanically isolated (except it is explicit marked on the system).
>> The system must be connected and operated to an earthed wall socket at the AC mains power supply only (except for DC systems).
>> Any other use than described above may damage your system and is attended with dangers like shortcut, fire or electric shocks.
10
SAFETY INSTRUCTIONS
>> The whole system must not be changed, rebuilt or opened (except for changing TRION™ modules).
>> If you assume a more riskless use is not provided anymore, the system has to be rendered inoperative and should be protected against inadvertent operation. It is assumed that a more riskless operation is not possible anymore, if
>
the system is damaged obviously or causes strange noises.
>
the system does not work anymore.
>
the system has been exposed to long storage in adverse environmental.
>
the system has been exposed to heavy shipment strain.
>> DO NOT touch any exposed connectors or components if they are live wired. The use of metal bare wires is not allowed. There is a risk of short cut and fire hazard!
>> Warranty void if damages caused by disregarding this manual. For consequential damages NO liability will be assumed!
>> Warranty void if damages to property or persons caused by improper use or disregarding the safety instructions.
>> Unauthorized changing or rebuilding the system is prohibited due to safety and permission reasons (CE).
Exception: changing TRION™ modules.
>> The assembly of the system is equivalent to protection class I. For power supply, only the correct power socket of the public power supply must be used, except the system is DC powered.
>> Be careful with voltages >25 VAC or >35 VDC! These voltages are already high enough in order to get a perilous electric shock by touching the wiring.
>> The maximum input voltage for input modules are 60 VDC and 42.4 VPEAK except for DAQP-LV module.
The maximum input voltage for DAQP-LV module is ±50 VDC or ±50 VPEAK. No measuring category according to IEC 61010-2-030:2010. The DAQP-LV must not be connected to mains circuit with overvoltage category II,III,IV.
Measurement category II is applicable to test and measuring circuits connected directly to utilization points of the low voltage mains installation. This part of installation is expected to have a minimum of 3 levels of overcurrent
protective devices between the transformer and the connecting points of the measuring circuit.
Measurement category III is applicable to test and measuring circuits connected to the distribution part of the buildings low voltage mains installation. This part of the installation is expected to have a minimum of two levels of
overcurrent protective devices between the transformer and possible connecting points.
Measurement category IV is applicable to test and measuring circuits connected at the source of the buildings low voltage mains installation. This part of the installation is expected to have a minimum of one level of overcurrent protective devices between the transformer and connecting points of thh measuring circuit.
DC model, connect power supply only to mains supply OVC II.
AC model, connect power supply only to mains supply OVC II.
>> The product heats during operation. Make sure there is adequate ventilation. Ventilation slots must not covered!
>> Only fuses of the specified type and nominal current may be used. The use of patched fuses is prohibited.
>> Prevent using metal bare wires! Risk of short cut and fire hazard!
>> DO NOT use the system before, during or shortly after a thunderstorm (risk of lightning and high energy
overvoltage). An advanced range of application under certain conditions is allowed with therefore designed products only. For details please refer to the specifications.
>> Make sure that your hands, shoes, clothes, the floor, the system or measuring leads, integrated curcuits and so on, are dry.
DEWE-3300 • Technical Reference Manual • Printing version 1.0.4 • August 29, 2017
11
SAFETY INSTRUCTIONS
>> DO NOT use the system in rooms with flammable gases, fumes or dust or in adverse environmental conditions.
>> Avoid operation in the immediate vicinity of:
>
>
high magnetic or electromagnetic fields
transmitting antennas or high-frequency generators
For exact values please refere to enclosed specifications.
>> Use measurement leads or measurement accessories aligned to the specification of the system only. Fire hazard in case of overload!
>> Do not switch on the system after transporting it from a cold into a warm room and vice versa. The thereby created condensation may damage your system. Acclimatise the system unpowered to room temperature.
>> Do not disassemble the system! There is a high risk of getting a perilous electric shock. Capacitors still might charged, even the system has been removed from the power supply.
>> Direct exposure of any DEWETRON product to strong sunlight or other heat radiation shall be prevented, as this could excessively heat up the product and lead to permanent damage of the product.
>> The electrical installations and equipments in industrial facilities must be observed by the security regulations and insurance institutions.
>> The use of the measuring system in schools and other training facilities must be observerd by skilled personnel.
>> The measuring systems are not designed for use at humans and animals.
>> Please contact a professional if you have doubts about the method of operation, safety or the connection of the system.
>> Please be careful with the product. Shocks, hits and dropping it from already lower level may damage your system. For exact values please refere to enclosed specifications.
>> Please also consider the detailed technical reference manual as well as the security advices of the connected systems.
This product has left the factory in safety-related flawless and proper condition.
In order to maintain this condition and guarantee safety use, the user has to consider the security advices and
warnings in this manual.
EN 61326-3-1:2008
IEC 61326-1 applies to this part of IEC 61326 but is limited to systems and equipment for industrial applications
intended to perform safety functions as defined in IEC 61508 with SIL 1-3.
The electromagnetic environments encompassed by this product family standard are industrial, both indoor
and outdoor, as described for industrial locations in IEC 61000-6-2 or defined in 3.7 of IEC 61326-1. Equipment
and systems intended for use in other electromagnetic environments, for example, in the process industry or in
environments with potentially explosive atmospheres, are excluded from the scope of this product family standard,
IEC 61326-3-1.
Devices and systems according to IEC 61508 or IEC 61511 which are considered as “operationally well-tried”, are
excluded from the scope of IEC 61326-3-1.
Fire-alarm and safety-alarm systems, intended for protection of buildings, are excluded from the scope of IEC 613263-1.
12
MAINTENANCE
Maintenance
The information in this section is designed for use by qualified service personal.
Service interval:
Clean dust from the chassis exterior/interior and exchange filter foam based on the operating environment.
Cleaning:
Clean surface of the chassis with dry lintfree cloth.
Use a dry velocity stream of air to clean the chassis interior.
!
> Disconnect all cables before servicing the unit!
> Many components within the chassis are sensitive to static discharge damage. Always wear a ground wrist strap and service the unit only in static-free environment.
> Do not use harsh chemical cleaning agents!
DEWE-3300 • Technical Reference Manual • Printing version 1.0.4 • August 29, 2017
13
GENERAL INFORMATION
CAUTION
> The system BIOS is protected by password. Any change in the BIOS may cause a system crash. When the system
is booting, do not press ESC-button on keyboard. This may clear the BIOS settings and cause system faults.
> Any change in the file structure as deleting or adding files or directories might cause a system crash.
> Before installing software updates contact DEWETRON or your local distributor. Use only software packages
which are released by DEWETRON. Further informations are also available in the internet (http://www.
dewetron.com).
> After power off the system wait at least 10 seconds before switching the system on again. Otherwise the
system may not boot correct. This prolongs also the life of all system components.
Windows updates and antivirus/security software
Before installing Windows software updates consult with DEWETRON for compatibility guidance. Please also keep in
mind that the use of any antivirus or other security software may slow down your system and may cause data loss.
Problematic network stacks
Often intrusive IT software or network processes can interfere with the primary function of the DEWETRON system: to
record data. Therefore we recommend strongly against the installation of IT/MIS software and running their processes
on any DEWETRON data acquisition system, and cannot guarantee the performance of our systems if they are so
configured.
Environmental Considerations
Information about the environmental impact of the product.
Product End-of-Life Handling
Observe the following guidelines when recycling a DEWETRON system:
System and Components Recycling
Production of these components required the extraction and use of natural resources. The substances
contained in the system could be harmful to your health and to the environment if the system is improperly
handled at it's end of life! Please recycle this product in an appropriate way to avoid an unnecessary pollution of the
environment and to keep natural resources.
This symbol indicates that this system complies with the European Union’s requirements according to Directive
2002/96/EC on waste electrical and electronic equipment (WEEE). Please find further information about recycling on
the DEWETRON website
www.dewetron.com
Restriction of Hazardous Substances
This product has been classified as Monitoring and Control equipment, and is outside the scope of the 2011/65/EU
RoHS Directive. This product is known to contain lead.
14
Main System
MAIN SYSTEM
DEWE-3300 - All-in-one standard instrument
>> Portable data acquisition system
>> Up to 16 channels with isolation
(in conjunction with DAQP/HSI/PAD series modules)
>> Up to 32 channels with differential inputs
(in conjunction with MDAQ series modules)
System specifications
DAQP / HSI / PAD amplifier slots
MDAQ amplifier input channels
Standard power supply
Rated input voltage
Power supply option
3300-PS-DC-200
Operating temperature
Storage temperature
Humidity (operating)
Vibration test*
EN 60068-2-6
Vibration test*
EN 60721-3-2
Class 2M2
Shocktests*
EN 60068-2-27
Dimensions (W x H x D)
Weight
DEWE-330x
16 (in conjunction with DEWE-3300 model)
up to 32 (in conjunction with DEWE-3301 model)
100 to 240 VAC (max. 90 to 264 VAC) 300 W AC power supply
11 to 27 VDC (max. 9 to 30 VDC ) ATX power supply, external AC power supply included (250 W)
0 °C to +50 °C
-20 °C to +70 °C
10 % to 80 %, non condensing
5 % to 95 % rel. humidity
Shape
Sine
Frequency range
10 - 150 Hz
Acceleration
2g
Sweep rate
1 oct./min.
Duration
20 Cycles
Test in 3 directions
Shape
Random
Frequency range
10 - 200 Hz
Power spectral density
1 m/s² / Hz from 10 – 200 Hz
Duration
30 Minutes per axis
Shape
Half-sine
Acceleration amplitude
15 g
Duration
11 ms
Test in 3 axis, 3 shocks in each axis and direction
approx. 462 x 320 x 135 mm (18.2 x 12.6 x 5.3 in.)
typ. 8.2 kg (18 lbs), depending on configuration
*) Tested with SSD disc
DEWE-3300 • Technical Reference Manual • Printing version 1.0.4 • August 29, 2017
15
MAIN SYSTEM
Base models
DEWE-3300
DEWE-3301
> 16 Slots for DAQP/HSI/PAD modules
> Digital I/O, counter and EPAD connector on top
Dimensions
320 mm (12.6 in.)
462 mm (18.2 in.)
5
13
m
m
.3
(5
.)
in
16
> up to 32 channels with MDAQ series modules
> Digital I/O, Counter, EPAD connector on side panel
MAIN SYSTEM
DEWE-330x at a glance
Typical DEWE-3300 front view
1
1
2
Typical DEWE-3300 top view
3 4
Slots for DAQP/HSI/PAD or MDAQ series
modules (depending on configuration)
2 15.6" (1920 x 1080px) multi-touch Full HD display
3 Digital I/O connector
4 EPAD connector
5 Optional counter input (B0_CNT0)
6 Optional counter input (B0_CNT1)
7 CAN interface connector
8 ORION-DAQ-SYNC interface
9 PS/2 interface connector
10 Ethernet LAN connector
11 RS-232 interface connectors
(COM1 & COM2)
12 VGA interface connector
13 Audio device
(LINE IN, MIC, LINE OUT)
14 DVI interface connector
External HDD access
15 USB 3.0 interface connector
16 USB 2.0 interface connector
17 Fold-out stand
18 Power supply input connector
19 HDD/SSD drive bays
20 Main power switch
21 Chassis terminal
5 6
Typical DEWE-3300 left side view
Typical DEWE-3301 right side view
7
8
9
10
10
11
4
5
6
12
13
3
17
18
16 15
14
19
20 21
Note: The location of the connectors (3), (4), (5),
(6) vary from system to system and depend on system configuration.
These connectors are not redundant.
DEWE-3300 • Technical Reference Manual • Printing version 1.0.4 • August 29, 2017
17
MAIN SYSTEM
1
Slots for DAQP/HSI/PAD or MDAQ series modules
Depending on your model, the DEWE-330x supports either 16 slots for DAQP/HSI/PAD modules or up to 32 channels
with differential inputs (MDAQ series modules). DAQP/HSI/PAD modules can be changed easily by the user while the
MDAQ series modules come predefined and are not user exchangeable.
2
15.6" multi-touch display
The DEWE-3300 is equipped with a bright 15.6" Full HD (1920 x 1080px) multi-touch panel.
3
Digital I/O connector
This connector supports digital input and output lines of the built-in DEWE-ORION series board. If this board does not
support digital I/O’s, the connector is not available.
Digital
Input
Counter
Input
Bx_DI 8
Bx_DO 0
Bx_DI 9
Bx_DO 1
Bx_DI 10
Bx_DO 2
Bx_DI 11
Bx_DO 3
Bx_DI 12
Bx_DO 4
Bx_DI 13
Bx_DO 5
Bx_DI 14
Bx_DO 6
Bx_DI 15
Bx_DO 7
-
EXT_CLK
-
RS-485A
-
EXT_Trigger
Bx_DI 0
Source Bx_CNT0
Bx_DI 1
Gate Bx_CNT0
-
EXT_CLK2
Bx-DI 2
Aux Bx_CNT0
Bx_DI 3
Source Bx_CNT1
-
EXT_CLK1
-
+5 DV
-
+5 DV
Counter Digital
Input
Input
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
DGND
-
DGND
-
DGND
-
DGND
-
DGND
-
DGND
-
DGND
-
DGND
-
DGND
-
RS-485B
-
DGND
-
Gate Bx_CNT1
Bx_DI 4
Aux Bx_CNT1.
Bx_DI 5
-
Bx_DI 6
-
Bx_DI 7
RES.*
-
DGND
-
DGND
-
Note: Only available for standard systems using
ORION-xxxx cards!
!
37-pin SUB-D connector
4
EPAD connector (LEMO)
To connect DEWETRON EPAD modules to the system.
Pin assignment
1: RS-485 A
4
1
2: RS-485 B
3
2
3: +12 V
4: GND
Lemo EGG.1B.304
Shield is connected on housing
Mating connector:
5,6
LEMO FGG.1B.304.CLAD52Z (for cable diameter 4.1 to 5.0 mm)
LEMO FGG.1B.304.CLAD62Z (for cable diameter 5.1 to 6.0 mm)
Optional counter inputs (in conjunction with DEWE-ORION-xxxx boards)
1: Source Bx_CNT(n)
2: Aux_Bx_CNT(n)
3: Gate Bx_CNT(n)
4: Power GND
5: +5 V (max. 500 mA)
6: +12 V (max. 500 mA)
7: Signal GND
n .. channels 0 to 1 of counter board
18
1
2
3
7
6
5
4
7-pin female LEMO connector
EGG.1B.307
Mating connector:
LEMO FGG.1B.307.CLAD52Z
(for cable diameter 4.1 to 5.0 mm)
LEMO FGG.1B.307.CLAD62Z
(for cable diameter 5.1 to 6.0 mm)
Cable to open end, 5 m long:
CTR-CBL-05
MAIN SYSTEM
7
CAN interface connectors
This connector supports the CAN signals of the built-in A/D board. If this board does not support CAN signals, the
connector is not available.
CAN 0:
CAN 1:
5 4 3 2 1
9 8 7 6
8
Pin assignment
1: +5 V
2: CAN0_L
3: GND
4: n.c.
5: n.c.
6: GND
7: CAN0_H
8: n.c.
9: +12 V
5 4 3 2 1
9 8 7 6
Pin assignment
1: +5 V
2: CAN1_L
3: GND
4: n.c.
5: n.c.
6: GND
7: CAN1_H
8: n.c.
9: +12 V
ORION-DAQ-SYNC
For high channel count or distributed systems, multiple instruments can be synchronized using the ORION-DAQ-SYNC
option. To simply daisy-chain systems, standard CAT6 cables with RJ45 connectors can be used for short distances. The
maximum lenght depends on the sampling rate and the A/D technology and ranges between 30 m to 200 m.
9
PS/2 interface connector
The PS/2 interface connector could be used to either connect a keyboard or an external PS/2 mouse. The connector
meets standard PS/2 pin assignment.
10
Ethernet LAN connector
The DEWE-3300 system supports 10/100/1000 BaseT Ethernet with standard RJ45 connector.
11
RS-232 interface connectors (COM1 & COM2)
The RS-232 interface connectors (male) are configured as standard RS-232 interface COM 1 & COM 2 and can be used
for mouse or other peripheral units.
1 2 3 4 5
9-pin SUB-D connector (male)
6 7 8 9
Schematic
Pin assignment
1: DCD (Data Carrier Detector)
2: RD (Received Data)
3: TD (Transmitted Data)
4: DTR (Data Terminal Ready)
5: GND (Ground)
6: DSR (Data Set Ready)
7: RTS (Request To Send)
8: CTS (Clear To Send)
9: RI (Ring Indicator)
DEWE-3300 • Technical Reference Manual • Printing version 1.0.4 • August 29, 2017
19
MAIN SYSTEM
12,14 VGA/DVI connector
The VGA connector offers the possibility to connect a standard VGA displays to the system and meets standard VGA
pin assignment. The DEWE-3300 offers an additional DVI connector.
13
Audio device
Connectors for LINE IN, MIC and LINE OUT.
15
USB3.0 interface connectors (Universal Serial Bus)
The USB3.0 interface connectors meet standard USB pin assignment.
16
USB2.0 interface connectors (Universal Serial Bus)
The USB2.0 interface connectors meet standard USB pin assignment.
17
Fold-out stand
The fold-out stand on the DEWE-3300 is designed to guarantee a secure stand and to facilitate touchscreen operations
within a slight pitch of the instrument.
18
Power supply input connector
For details see chapter power supply.
19
HDD/SSD drive bays
The DEWE-3300 comes with 2 drivebays for easy access to your HDD/SSD including a 1 TB HDD dedicated for data
storage as well as a 120 GB SSD for operating system and application software.
Optional upgrades:
>
HDD-1T-SSD-120G
Upgrade to industrial grade 120 GB solid state disk (replaces 1 TB harddisk)
>
HDD-1T-SSD-500G
Upgrade to industrial grade 500 GB solid state disk (replaces 1 TB harddisk)
>
HDD-1T-SSD-1T
Upgrade to industrial grade 1 TB solid state disk (replaces 1 TB harddisk)
CAUTION:
Information for systems with SSD drives
!
Wait for 40 seconds after big files were deleted. The HDD activity LED is lit to indicate that the SSD
is deleting the file and TRIM/garbage collection is in progress. Wait until the process is finished before you start to write the next file.
20
Power-on switch
The power-on switch is used to switch on the system.
21
Chassis terminal
For some kind of measurements, it’s necessary to provide the system with an additional ground connection.
20
MAIN SYSTEM
Optional connector for current power probe supply
This connector supports ±9 V current power probe supply for connecting current clamps.
3-pin Binder series connector
1
3
2
Pin assignment
1: +9 V
2: GND
3: -9 V
BINDER-712 series
6-pin male/female Lemo connector (with digital inputs of ORION board)
3 2 1
4 5 6
Lemo ERA.1S.306
Pin assignment
1: +15 V
2: -15 V
3: +9 V
4: DGND
5: DI(x)
6: DGND
x .. digital inputs 0..7 of the ORION board
DEWE-3300 • Technical Reference Manual • Printing version 1.0.4 • August 29, 2017
21
MAIN SYSTEM
Possible configurations and panel options
0.5 U
1.5 U
1.5 u panel space available for DIO panels in AC
powered systems
1.5 u panel space available for DIO panels in systems with
DC power option
Choose between a panel with 8 additional counter
inputs or a power supply for 4 current clamps.
Depending on the application, the DEWE-3300 offers
various DIO panels. For encoder measurements the
ORION-DIO-PANEL-1 is the right choice since it offers eight
counters wired to 7-pin LEMO connectors. The ORIONDIO-PANEL-2 has been designed for applications where
many TTL-inputs are required. For galvanically isolated
digital inputs the ORION-DIO-PANEL-3 would be the right
choice.
0.5U-ORION-CNT8-LEMO
0.5U-CLAMP-DC-POWER-4
330x-OUT-10
NOTE: Pinning of the optional ORION-DIO-
PANELS are shown in the corresponding
DEWE-ORION series technical reference
manual.THESE PANELS ARE NOT USER
EXCHANGEABLE! Please ask you local
distributor or DEWETRON directly for
more information.
ORION-DIO-PANEL-1
!
ORION-DIO-PANEL-2
MPAD-TH16-K
22
MAIN SYSTEM
Power supply
AC standard power supply
300 W AC power supply
Input:
Rated input range:
Input frequency:
Input current:
P1S-6300V-B2
100 to 240 VAC, (max. 90 .. 264 VAC) active PFC
47 .. 63 Hz
4.5 A @ 115 V / 2 A @ 230 V
Output:
Output power:
Output voltages:
300 W total
+12 V1 (max. 8 A)
+12 V2 (max. 16 A)
+5 V (max 18 A)
+3.3 V (max 17 A)
-12 V (max. 0.3 A)
+5 Vsb (max. 2.5 A)
Protection:
Short circuit protection:
Overload protection:
Overvoltage protection:
+3.3 V, +5 V, +12 V, switch off / -12 V, +5 Vsb, auto recovery
110 .. 160 %, switch off
+3.3 V (+3.6 .. +4.3 V), +5 V (+5.6 .. +6.5 V), +12 V (+13.2 .. +15 V)
AC power supply
AC power switch
DC power supply (option 3300-PS-DC-200)
250 W DC power supply
Input:
Input range:
Input frequency:
Output:
Output power:
Output voltages:
Rated 11 to 27 VDC (max. 9 to 30 VDC)
DC
max. 250 W
+3.3 V (max. 15 A)
+5 V
(max. 15 A)
+5 Vsb (max. 1.5 A)
+12 V (max. 12 A)
-12 V (max. 0.15 A)
12 V rail output current (12 V buck/boost converter)
Input range:
12 V out current:
6 to 8 V:
8A
8 to 11 V:
10 A (12 A peak)
11 to 16 V:
12 A (16 A peak)
16 to 30 V:
12 A (14 A peak)
Power supply pin assignment:
+
-
Connector type
2-pin. male
LEMO EGJ.2B.302
DEWE-3300 • Technical Reference Manual • Printing version 1.0.4 • August 29, 2017
23
MAIN SYSTEM
External AC/DC power supply (standard accessory included with option 3300-PS-DC-200)
200 W AC power supply
Input:
Rated input voltage:
Input frequency:
100 .. 240 VAC (max. 90 .. 264 VAC)
47 .. 63 Hz
Output:
Output power:
Output voltage:
200 W total
+24 V (max. 8.3 A)
Protection
Overvoltage protection:
Short circuit:
yes
yes
Environment:
Temperature:
Humidity:
Operating: 0 to 40 °C / Storage: -20 to 80 °C
Operating: 20 % RH to 80 % RH / Storage: 10 % RH to 90 % RH
Power supply pin assignment:
DEWE-3300 with option '3300-PS-DC-200'
and included external AC/DC power supply
+
-
Connector type
2-pin. male
LEMO EGJ.2B.302
external AC/DC power supply
100 to 240 VAC IN
24
A/D Conversion
A/D & D/A CONVERSION
A/D Conversion
Please find information about the A/D conversion in the attached DEWE-ORION series manual.
The latest version of the manual can be downloaded from:
https://ccc.dewetron.com/pl/a-d-boards
Informations regarding different manufacturer's see the corresponding D/A card manual.
DEWE-3300 • Technical Reference Manual • Printing version 1.0.4 • August 29, 2017
A1
A/D & D/A CONVERSION
Notes
A2
Internal Wiring
INTERNAL WIRING
16 slot DEWE-MOTHERBOARD DAQ-MOTH-16-DE-x
Rear view
W7
W1
Front view
5 = 5 V output; 330 kHz filter
10 = 10 V output; 330 kHz filter
GND
+15 V ORION
-15 V ORION
CH 0
W10
CH 1
W11
16 channels single ended
analog output
(output resistance 15 Ohm)
Please find the pin-assignment
on the next page!
W8
CH 2
CH 3
W9
5 V ORION
Ext. CLK
Ext. TRIG
DGND ORION
Ext. CLK 2 OUT
Ext. CLK 1 OUT (CAMERA TRIGGER)
CH 4
DGND ORION
CH 5
W5
CH 6
CH 7
Terminate RS-485
Connect GND to GNDP
W3 Connect +12 V to +V (pin 6)
W4 Terminate RS-485
W5 Connect chassis to GND
W6 Connect chassis to GND
W7 Connect chassis to GND
W8 Activate ORION RS-485 (A)
W9 Activate ORION RS-485 (B)
W1
16x GND
16 x analog OUT (resistance 50 Ohm)
GND
W2
CH 8
CH 9
CH 10
CH 11
Activate analog output 0 on CH 14
W11 Activate analog output 1 on CH 15
W10
CH 12
Note: If you connect signals to these
contacts you have to open the solder
jumpers W10 and W11 first!
CH 13
CH 14
Connection to CH14 (pin 7)
Indicator
+9 V
-9 V
CH 15
Connection to CH15 (pin 7)
1 2 3 4 5
RES
GND
POWER
W4
+V
+12 V
GNDP
-12 V
-V
A (RS-485)
GNDC
B (RS-485)
GNDP
+V
+12 V
-12 V
-V
RS-232
RS-485
USB
W3
W6
GNDC
GNDC
TX
RX
POWER
W2
RS-485
DM
DP
GNDC
RX
TX
GNDC
B
B
A
A
6 7 8 9
9-pin SUB-D pin assignment:
GND
1
2
3
4
5
6
7
8
9
Module input (±5 V)
RS-485 (A)
RS-485 (B)
GND
+9 V power supply
+12 V power (default) /
+V sensor supply
Module output
(from A/D board)
-V sensor supply
-9 V power supply
The 16 slot DEWE-MOTHERBOARD receives the ±12 VDC power supply via a DC/DC converter from the
internal power supply.
DEWE-3300 • Technical Reference Manual • Printing version 1.0.4 • August 29, 2017
B1
INTERNAL WIRING
Analog output connector pin-assignment
Connector for DEWE-ORION-1616 cards
+15 V
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AISENSE2
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AISENSE1
AGND
DI8/DO0
DI9/DO1
DI10/DO2
DI11/DO3
DI12/DO4
DI13/DO5
DI14/DO6
DI15/DO7
+5 V
DGND
DGND
+5 V
DGND
DGND
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Connector for DEWE-ORION-1624 cards
-15 V
AGND
AGND
CH15+
CH14+
CH13+
CH12+
CH11+
CH10+
CH9+
CH8+
CH7+
CH6+
CH5+
CH4+
CH3+
CH2+
CH1+
CH0+
AGND
DI0/Source(0)
DI1/Gate(0)
DI2/AUX_U_D(0)
DI3/Source(1)
DI4/Gate(1)
DI5/AUX_U_D(1)
RS-485A
RS-485B
DI 6
DI 7
EXT_CLK
EXT_Trigger
EXT_CLK1
EXT_CLK2
+15V
AGND
AGND
CH. 15CH. 14CH. 13CH. 12CH. 11CH. 10CH. 9CH. 8CH. 7CH. 6CH. 5CH. 4CH. 3CH. 2CH. 1CH. 0AGND
NC.
NC.
NC.
NC.
NC.
NC.
NC.
NC.
+5 V
DGND
DGND
+5 V
DGND
DGND
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
-15 V
AGND
AGND
CH. 15+
CH. 14+
CH. 13+
CH. 12+
CH. 11+
CH. 10+
CH. 9+
CH. 8+
CH. 7+
CH. 6+
CH. 5+
CH. 4+
CH. 3+
CH. 2+
CH. 1+
CH. 0+
AGND
NC.
NC.
NC.
NC.
NC.
NC.
RES.*
RES.*
RES.*
RES.*
RES.*
EXT-TRIGGER
SAMPLE CLOCK
NC.
* DONT CONNECT
68-pin high density connector
68-pin high density connector
16 slot DEWE-MOTHERBOARD DAQ-MOTH-16-NI-x-U
5 = 5 V output; 330 kHz filter
10 = 10 V output; 330 kHz filter
USB interface on-board
Connector for National InstrumentsTM A/D cards
DGND
DGND
PFI 8/P2.0
PFI 7/P1.7
PFI 15/P2.7
PFI 13/P2.5
PFI 4/P1.4
PFI 3/P1.3
PFI 2/P1.2
DGND
PFI 10/P2.2
PFI 11/P2.3
P0.3
P0.7
P0.2
DGND
P0.5
P0.0
DGND
AO GND
AO GND
AI GND
AI 7
AI 14
AI GND
AI 5
AI 12
AI Sense
AI 11
AI GND
AI 2
AI 9
AI GND
AI 0
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
PFI 14/P2.6
PFI 112/P2.4
PFI 9/P2.1
DGND
PFI 6/P1.6
PFI 5/P1.5
DGND
+5 V
DGND
PFI 1/P1.1
PFI 0/P1.0
DGND
DGND
+5 V
DGND
P0.6
P0.1
DGND
P0.4
APFI 0
AO 1
AO 0
AI 15
AI GND
AI 6
AI 13
AI GND
AI 4
AI GND
AI 3
AI 10
AI GND
AI 1
AI 8
68-pin high density connector
B2
Rear view
W7
DGND
W1
16 channels single ended
analog output
(output resistance 15 Ohm)
Please find the pin-assignment
on the next page!
Analog OUT Ch. 1
Analog OUT Ch. 0
Terminate RS-485
Connect GND to GNDP
W3 Connect +12 V to +V (pin 6)
W4 Terminate RS-485
W5 Connect chassis to GND
W6 Connect chassis to GND
W7 Connect chassis to GND
W1
W2
DGND
GND
INTERNAL WIRING
Please find information about the MDAQ amplifiers in the attached DEWE-MDAQ series manual. The latest
version of the manual can be downloaded from:
https://ccc.dewetron.com/pg/mdaq-modules
DEWE-3300 • Technical Reference Manual • Printing version 1.0.4 • August 29, 2017
B3
INTERNAL WIRING
Notes
B4
CE-Certificate of Conformity
Manufacturer:
DEWETRON GmbH
Address:
Parkring 4
8074 Grambach, Austria
Tel.: +43 316 3070 0
Fax: +43 316 3070 90
e-mail: [email protected]
http://www.dewetron.com
Name of product:
DEWE-3300
Kind of product:
Data acquisition instrument
The product meets the regulations of the following EC-directives:
2014/35/EU
"Directive of the European Parliament and of the Council of 26 February 2014 on the
harmonisation of the laws of the Member States relating to the making available on the
market of electrical equipment designed for use within certain voltage limits"
2004/108/EC
"Directive on the approximation of the laws of the Member States relating to
electromagnetic compatibility amended by the directives 89/336/EWG."
The accordance is proved by the observance of the following standards:
L
V
E
M
C
Safety
IEC 61010-1:2011 300 V CATII, Pol. Deg. 2
Emissions
EN 61000-6-4
EN 55011 Class B
Immunity
EN 61000-6-2
Group standard
Graz, October 07, 2015
Place / Date of the CE-marking
Ing. Thomas Propst / Manager Total Quality
DEWE-3300 • Technical Reference Manual • Printing version 1.0.4 • August 29, 2017
C1
NOTES
C2
">