15 TONNE HYDRAULIC PRESS OPERATION & MAINTENANCE INSTRUCTIONS MODEL NO: AHP 16

Add to my manuals
12 Pages

advertisement

15 TONNE HYDRAULIC PRESS OPERATION & MAINTENANCE INSTRUCTIONS MODEL NO: AHP 16 | Manualzz

WARNING: Read these instructions before using the machine

15 TONNE HYDRAULIC PRESS

MODEL NO: AHP 16

PART NO: 7615103

OPERATION & MAINTENANCE

INSTRUCTIONS

LS1211

INTRODUCTION

Thank you for purchasing this CLARKE 15 tonne Hydraulic Press

Before attempting to operate the machine, it is essential that you read this manual thoroughly and carefully follow all instructions given. In doing so you will ensure the safety of yourself and that of others around you, and you can also look forward to the press giving you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of

12 months from the date of purchase. Please keep your receipt as proof of purchase.

This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended.

Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission.

This guarantee does not effect your statutory rights.

SAFETY PRECAUTIONS

• During assembly or if the press is moved, ALWAYS use a suitable crane or hoist, do not manhandle.

• Ensure the press is located on firm level ground with adequate light.

• Before applying a load, ensure both press bed support pins are fully engaged.

• Ensure that hydraulic hoses and couplings are completely sound.

• Before use, always ensure the workpiece is firmly secure and stable.

• Always clean spills of hydraulic oil immediately as this can be dangerous in a workshop environment.

• Do not exceed the rated capacity of the press.

• Do not allow any person who is inexperienced in the use of hydraulic presses, to use the press unless they are under direct supervision.

• Do not allow anyone to work directly in front of the press when it is in use.

2

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

• Never tamper with the press. The safety valve is calibrated and sealed at the factory; do not attempt to change the setting.

• Use only the recommended hydraulic oil.

• Components of this press are specially designed to withstand the rated capacity. Do not substitute bolts, pins, or any other components.

• Always apply the load under the centre of the ram. Offset loads can damage the ram or ram mount and may cause the work piece to eject.

• Before operating, check for signs of cracked welds, bent bed pins, loose or missing bolts, or any other structural damage. Do not operate if any of these conditions exist. Have repairs made only by authorised service centre.

• Remove load from press bed before attempting to adjust bed height.

• Press only on a work piece supported by the press bed.

• When using accessories such as arbor plates, be certain they are centered below the ram and are in full contact with the bed.

• Parts being pressed may splinter, shatter, or be ejected from the press. Due to varied applications, it is your responsibility to always use adequate guards, wear eye protection and protective clothing when operating this press.

• Keep hands and fingers away from parts that may pinch and shift.

• Keep warning decals legible and intact. Replacements may be obtained from Clarke International Spare Parts Department.

• Failure to heed these warnings may result in damage to the equipment, or failure resulting in property damage, personal, or even fatal injury.

• DO NOT use extension tubes on the pump handle. Excessive effort can cause damage and/or accidents.

3

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

ASSEMBLY

Ensure the press and its components suffered no damage during transit.

Should any damage be apparent, please contact your CLARKE dealer immediately.

IMPORTANT: Due to the weight of the press, we recommend that you get assistance from another person during assembly.

1. With the main frame upright and adequately supported, bolt on the two feet using the nuts and bolts supplied.

IMPORTANT: We strongly recommend that the press be firmly secured to a firm and level floor using expansion bolts (not supplied).

2. Remove the plug on the front of the pump body and replace it with the vent plug supplied.

3. Remove the cap on top of the ram. Seal the thread with PTFE tape and screw in the pressure gauge, ensuring it is tight.

4. Fit the pump handle into the actuating lever.

NOTE: Do not locate your press where it will be open to the elements, as it is designed to operate at temperatures of between -10

O

C to 40

O

C. Severe weather conditions will damage the hydraulic system.

5. Insert the two supporting pins into the lowest holes on the frame, one each side.

6. With assistance place the bed on top of the two pins.

BED HEIGHT

Position the bed at the desired height, so as it will be as close as possible to the ram when the workpiece is mounted.

IMPORTANT: Due to the weight of the bed, we recommend that you get assistance from another person when adjusting the bed height.

1. Raise one side of the bed, and insert a supporting pin into the next locating hole.

2. Repeat at the other end of the bed to level out the bed,

3. Repeat steps 1 and 2 until the bed is at the desired height, with the supporting pins fully ‘home’.

CAUTION: THE BED HEIGHT SHOULD ONLY BE RAISED OR LOWERED 1

HOLE AT A TIME, WORKING ALTERNATELY FROM ONE SIDE AND THEN THE

OTHER, FAILURE TO WORK IN THIS WAY MAY CAUSE THE BED TO FALL

AND CAUSE INJURY TO THE OPERATOR

4

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

POSITIONING THE RAM

The ram can positioned as required by sliding it along the top rail.

• Always position the ram directly above the workpiece.

HYDRAULIC PUMP/RAM OPERATION

The pump is provided with two valves, operated by turning the respective handwheel as shown.

Valve A is used for raising or lowering the ram.

Turn the handwheel clockwise and pump the handle to operate (or lower) the ram. Turning the handwheel anticlockwise releases the pressure and the ram will rise.

Valve B is used to move the ram in fast or slow mode.

Turn the handwheel clockwise and pump the handle to move the ram quickly to the workpiece. Turning the handwheel anticlockwise and pumping the handle moves the ram at a slower rate.

5

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

OPERATION

1. Place the workpiece on the bed.

• It must be completely stable. you must use packing or shims where required.

‘Vee’ blocks and a supporting plate are supplied, which locate on the bed.

Place the workpiece on a combination of these to give it stability.

DO NOT ‘point load’ these accessories as they are not designed to take the full force of the ram in one spot. Ensure they are adequately supported.

NOTE: Any packing pieces or shims used MUST be capable of

withstanding the pressure that will be brought to bear, and MUST be of sufficient size with sufficient surface area, so as to avoid the possibility of slipping or springing out. Mating surfaces MUST be horizontal so that the force being exerted will NOT be at an angle.

2. Turn the Handwheel B, clockwise to move the ram quickly, and

Handwheel A, clockwise to lower the ram.

3. Pump the handle to bring the ram

very lightly into contact with the workpiece.

4. Manoeuvre the workpiece or slide the ram so that the desired point of contact is directly beneath the

centre of the ram.

5. When satisfied that the workpiece is correctly lined up and is completely stable in that position, ensure the handwheel B, is turned

ANTICLOCKWISE, and slowly pump the handle so that the ram begins to exert pressure on the workpiece.

Continue to pump the handle whilst standing to the side. Do NOT stand directly in front of the work, and constantly monitor the process, ensuring the ram and work remain completely in line, and there is no risk of slipping.

6. When the process is complete, turn the handwheel A, anticlockwise to release ram pressure.

WARNING: NEVER use extensions to the ram pumping handle

6

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

MAINTENANCE

A visual inspection must be made before each use of the press, checking for leaking hydraulic fluid, and damaged, loose or missing parts.

Owners and/or users should be aware that repair of this equipment may require specialised knowledge and facilities. It is recommended that a thorough annual inspection of the press be made and that any defective parts, decals or warning labels be replaced with genuine Clarke parts.

Any press which appears to be damaged in any way, is found to be badly worn, or operates abnormally SHOULD BE REMOVED FROM SERVICE until the necessary repairs are made.

PERIODICALLY

• Check the press frame to make sure all bolts are tight and inspect for cracked welds, bent, loose or missing parts.

• Check the hydraulic connections for leaks. Replace or properly repair any damaged or leaking hydraulic components before using.

EVERY 6 MONTHS

• Check the hydraulic pump oil level, by removing the plug from the front of the unit. Oil should be level with the bottom of the hole. If necessary top up with CLARKE Hydraulic Oil, Part No. 3050830 only. This operation is carried out

with the ram fully retracted.

EVERY 2 YEARS

• Replace the hydraulic oil. This operation requires the dismantling of the hydraulic system, for which you should consult your CLARKE dealer.

• If any rust is apparent it must be removed completely and reinspected.

7

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

SPECIFICATIONS

Capacity

Pressure

15 tonne

390 Bar

Ram Stroke 160 mm

Ram Diameter 40 mm

Net Weight 120 kg

H

L

D

E

F

G

Dimensions

A

B

C

170 mm

550 mm

1000 mm

125 mm

160 mm

900 mm

600 mm

1950 mm

125 mm

8

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

PARTS DIAGRAM

PART NO DESCRIPTION

A0315

A0346

B4949

B5047

B5863

R0046

R0058

R0093

R0132

R0140

Nut M12

Washer 12 x 24

Bolt TE M12 x 40

Gasket with 1/4” seal

Connector for gauge

Nut M12

Pressure Gauge

Bed Supporting Pin 25 x

320mm

Washer 3/8”

Bolt TE M12 x 90

PART NO DESCRIPTION

R0266

R1182

R1651

R1656

R1664

R1668XX

R1673XX

R1680

Spacer

Pump Assembly

Flexible pipe

Working Plane

V-Block

Foot

Frame

Cylinder Assembly

R3053 Connector M-M 1/4” X3/8”

9

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

DECLARATION OF CONFORMITY

10

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

NOTES

11

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement