Viking Dcwh3644ss Quick Specs

VENTILATION
Built-In Classic Chimney Wall Hood—
Standard, w/Ledge, & Ledgeless
Standard Features & Accessories
All models include
• Adjustable duct cover (for 8 – 9’
ceilings) is standard
• Must also purchase interior, exterior or
in-line ventilator kit, sold separately
(see Installation Notes & Accessories
for recommended Viking ventilator
products)
• Heat sensor turns the ventilator on full
power when cooking temperatures
reach uncomfortable levels
• Variable speed controls for custom
venting—separate on/off switch allows
you to leave ventilator at favorite/mostused setting
• 12-hour timer built into ventilator
controls
• Delay feature allows you to set the
ventilator to shut off on its own from
10 to 30 minutes later
• 24”D. (tests show 24”D. hoods perform
properly over 27”D. ranges)
• Heavy-duty construction; sleek,
contemporary design and styling
o Virtually seamless stainless steel
design with no visible screws
• Easy cleanup
o Dishwasher-safe, stainless steel mesh
filters efficiently remove grease and
heated vapors from the air, and are
easily removed for quick cleaning
(frame and mesh are stainless steel)
• See Dimensions & Specifications
table for number of filters per model
o Design of low-profile filter system
means less interior hood space to be
cleaned
o Canopy interior is completely lined in
stainless steel for increased rigidity,
seamless appearance, and easy cleaning
• 50-watt halogen lights with dimmer
control
• Power switch and dimmer control are
separate, allowing you to leave dimmer
at favorite position
o See Dimensions & Specifications
table for number of lights per model
Model numbers
CLASSIC CHIMNEY WALL HOODS
•
•
•
•
DCWH3042—30”W./12”H.
DCWH3644—36”W./14”H.
DCWH4244—42”W./14”H.
DCWH4844—48”W./14”H.
CLASSIC CHIMNEY WALL HOODS WITH
LEDGE
•
•
•
•
DCWL3342—33”W./12”H.
DCWL3944—39”W./14”H.
DCWL4544—45”W./14”H.
DCWL5144—51”W./14”H.
CLASSIC CHIMNEY WALL HOODS,
LEDGELESS
• DCWN3042—30"W./12"H.
• DCWN3644—36"W./14"H.
• DCWN4244—42"W./14"H.
DCWN4844—48"W./14"H.
Model Options
DCWH Designer
Chimney Wall Hood*
DCWL Designer
Chimney Wall Hood
w/Ledge*
DCWN Designer
Chimney Ledgeless
Wall Hood*
FINISH DETAILS
• Stainless Steel (SS), Black (BK), White
(WH), Metallic Silver (MS), Graphite Gray
(GG), Stone Gray (SG), Taupe (TP), Biscuit
(BT), Cotton White (CW), Oyster Gray
(OG), Golden Mist (GM), Lemonade (LE),
Sage (SA), Mint Julep (MJ), Sea Glass (SE),
Iridescent Blue (IB), Viking Blue (VB),
Pumpkin (PM), Racing Red (RR), Apple
Red (AR), Burgundy (BU), Plum (PL),
Chocolate (CH), and Cobalt Blue (CB).
• Accessory Rail Option*—Front of hood.
(Must be ordered factory installed. Rail not
available on ledge & ledgeless models.)
o Stainless Steel/Chrome (CR)—Stainless
steel rail with chrome supports/brackets
and hooks (included).
o Brass Rail Option (BR)—nameplate, rail,
supports/brackets, and hooks
(included). Brass components have a
durable protective coating for
maintenance-free normal use.
*Shown throughout with adjustable duct cover, included.
ORDERING INSTRUCTIONS
First specify model number, followed by color code (DCWH3042SS). If ordering optional decorative rail, specify code at end
(DCWH3042SSCR).
PLANNING AND DESIGN GUIDE
VIKINGRANGE.COM
•
1-888-VIKING1
REVISED 5/2/11
© 2 0 1 1 V R C — INFORMATION SUBJECT TO CHANGE
VENTILATION
Built-In Classic Chimney Wall Hood—Standard
✪
Dimensions & Specifications
Please see
Installation Notes &
Accessories for
PRODUCT DIMENSIONS
important information,
including ventilator
kits, duct covers,
backsplashes, and
warming shelf
panels.
DCWH Designer
Chimney Wall Hood
”
12 cm)
.5
( 30
C
D
2
( 5. ”
1c
m)
B
A
”
24 cm)
(61
.0
CHIMNEY WALL HOOD
Model
Hood
Width (A)
Height (B)
DCWH3042
29-7/8” (75.9 cm)
12” (30.5 cm)
DCWH3644
35-7/8” (91.1 cm)
14” (35.6 cm)
DCWH4244
41-7/8” (106.4 cm)
14” (35.6 cm)
DCWH4844 47-7/8” (121.6 cm)
14” (35.6 cm)
Width (C)
Duct Cover
Depth
10” (25.4 cm) 12” (30.5 cm) 18” (45.7 cm)—
30” (76.2 cm)
12” (30.5 cm) 12” (30.5 cm) 16” (40.6 cm)—
28” (71.1 cm)
12” (30.5 cm) 12” (30.5 cm) 16” (40.6 cm)—
28” (71.1 cm)
18” (45.7 cm) 12” (30.5 cm) 16” (40.6 cm)—
28” (71.1 cm)
PLANNING AND DESIGN GUIDE
VIKINGRANGE.COM
•
1-888-VIKING1
Lights
Filters
Heat
Lamps
Approx.
Ship. wt.
2
2
N/A
2
2
N/A
2
3
N/A
3
3
N/A
51 lbs.
(23.1 kg)
61 lbs.
(27.7 kg)
71 lbs.
(32.2 kg)
82 lbs.
(37.2 kg)
Height (D)
REVISED 5/2/11
© 2 0 1 1 V R C — INFORMATION SUBJECT TO CHANGE
VENTILATION
Built-In Classic Chimney Wall Hood—
w/Ledge, & Ledgeless
✪
Dimensions & Specifications
Please see
Installation Notes &
Accessories for
PRODUCT DIMENSIONS
important information,
including ventilator
kits, duct covers,
backsplashes, and
warming shelf
panels.
DCWL Designer
Chimney Wall Hood
w/Ledge
”
12 cm)
.5
( 30
DCWN Designer
Chimney Ledgeless
Wall Hood
”
12 cm)
.5
( 30
C
2
( 5. ”
1c
m)
C
D
D
B
B
A
”
24 cm)
A
2”
-1/ )
25.8 cm
CHIMNEY WALL
HOOD LEDGE
Model
Hood
Width (A)
Height (B)
DCWL3342
32-7/8” (83.5 cm)
12” (30.5 cm)
DCWL3944
38-7/8” (98.4 cm)
14” (35.5 cm)
DCWL4544
44-7/8” (114.0 cm)
14” (35.5 cm)
DCWL5144
50-7/8” (129.2 cm)
14” (35.5 cm)
DCWN3042 29-7/8” (75.9 cm)
12” (30.5 cm)
DCWN3644 35-7/8” (91.1 cm)
14” (35.5 cm)
DCWN4244 41-7/8” (106.4 cm)
14” (35.5 cm)
DCWN4844 47-7/8” (121.6 cm)
14” (35.5 cm)
(64
Width (C)
Duct Cover
Depth
•
CHIMNEY WALL
HOOD LEDGELESS
30” (76.2 cm)
12” (30.5 cm) 12” (30.5 cm) 16” (40.6 cm)—
28” (71.1 cm)
12” (30.5 cm) 12” (30.5 cm) 16” (40.6 cm)—
28” (71.1 cm)
18” (45.7 cm) 12” (30.5 cm) 16” (40.6 cm)—
28” (71.1 cm)
1-888-VIKING1
Lights
Filters
Heat
Lamps
Approx.
Ship. wt.
2
2
N/A
2
2
N/A
2
3
N/A
3
3
N/A
2
2
N/A
54 lbs.
(24.5 kg)
64 lbs.
(29.0 kg)
74 lbs.
(33.6 kg)
85 lbs.
(38.6 kg)
51 lbs.
2
2
N/A
2
3
N/A
3
3
N/A
Height (D)
10” (25.4 cm) 12” (30.5 cm) 18” (45.7 cm)—
30” (76.2 cm)
12” (30.5 cm) 12” (30.5 cm) 16” (40.6 cm)—
28” (71.1 cm)
12” (30.5 cm) 12” (30.5 cm) 16” (40.6 cm)—
28” (71.1 cm)
18” (45.7 cm) 12” (30.5 cm) 16” (40.6 cm)—
28” (71.1 cm)
10” (25.4 cm) 12” (30.5 cm) 18” (45.7 cm)—
PLANNING AND DESIGN GUIDE
VIKINGRANGE.COM
.0
(61
(23.1 kg)
61 lbs.
(27.7 kg)
71 lbs.
(32.2 kg)
82 lbs.
(37.2 kg)
REVISED 5/2/11
© 2 0 1 1 V R C — INFORMATION SUBJECT TO CHANGE
VENTILATION
Built-In Classic Chimney Wall Hood—
Standard, w/Ledge, & Ledgeless
Dimensions & Specifications
CLEARANCE DIMENSIONS
CHIMNEY WALL HOOD
66
(16 ”m
7.6 in.
c
72 t o m)
(18 ”ma
2.9 x.
cm
)
30
(76”mi
.2 n.
c
36 to m)
(91”ma
.4 x.
cm
)
”
3 6 cm )
.4
(91
CHIMNEY WALL HOOD
LEDGE/LEDGELESS
66
(16 ”m
7.6 in.
c
72 to m)
(18 ”ma
2.9 x.
cm
)
30
(76”mi
.2 n.
c
36 to m)
(91”ma
.4 x.
cm
)
”
36 cm)
.4
(91
Note: For best performance and safe, efficient operation,
it is recommended that the bottom of the hood be 30”
(76.2 cm) to 33” (83.8 cm) above the countertop.
PLANNING AND DESIGN GUIDE
VIKINGRANGE.COM
•
1-888-VIKING1
REVISED 5/2/11
© 2 0 1 1 V R C — INFORMATION SUBJECT TO CHANGE
VENTILATION
Built-In Classic Chimney Wall Hood—
Standard, w/Ledge, & Ledgeless
Installation Requirements
DCWH Designer
Chimney Wall Hood
DCWL Designer
Chimney Wall Hood
w/Ledge
DCWN Designer
Chimney Ledgeless
Wall Hood
UTILITY REQUIREMENTS
Proper installation/ducting is extremely
important to ensure maximum
performance. Use a qualified and
trained installer.
o Straight runs and gradual
turns are best; for example,
each 90” elbow is equivalent
to 5’ – 10’ (1.52 – 3.05 cm) of
straight run.
• 7’ round duct for 300 – 600
CFM; 10’ for 900 – 1500 CFM
o Never use flexible duct; it
creates back pressure/air
turbulence and greatly
reduces performance.
VENTILATION
• Check with a qualified and
trained installer or local codes
for makeup air requirements, if
any.
• Max. duct run
o For 300 – 1,200 CFM—50’
(15.2 m)
o For 1,500 CFM—75’ (22.9 m)
o Duct run length is for general
reference only; always use a
qualified and trained installer.
ELECTRICAL
• Hardwire direct with two-wire
with ground
• 120 VAC/60 Hz
• Max. amp usage (rating
includes rec. ventilator kit
rating)
PLUMBING
Not applicable
GAS
Not applicable
Note: All CFMs are based on tests with 0.1 static pressure. Without applying static pressure (some brands do not), CFM could be greatly
overstated.
Model
Ventilator kits
Interior
Exterior
DCWH3042
DIV300/DIV440
DCWH3644
DIV300/DIV600*
DCWH4244
DIV600
DCWH4844
DIV1200*
DCWL3342
DIV300/DIV440
DCWL3944
DIV300/DIV600*
DCWL4544
DIV600
DCWL5144
DIV1200
DCWN3042
DIV300/DIV440
DCWN3644
DIV300/DIV600*
DCWN4244
DIV600
DCWN4844
DIV1200*
DEV900/DEV1200
DIL900/1200
DEV900/DEV1200*
DIL900/1200
DEV900/DEV1200*
DIL900/1200
DEV1200/DEV1500**
DIL1200
DEV900/DEV1200
DIL900/1200
DEV900/DEV1200*
DIL900/1200
DEV900/DEV1200*
DIL900/1200
DEV1200/DEV1500**
DIL1200
DEV900/DEV1200
DIL900/1200
DEV900/DEV1200*
DIL900/1200
DEV900/DEV1200*
DIL900/1200
DEV1200/DEV1500**
DIL1200
Duct size
Max. amps
Interior
Exterior
Interior
Exterior
7” (17.8 cm)
10” (25.4 cm)
1.7/3.2
6.6/3.9
7” (17.8 cm)
10” (25.4 cm)
1.7/3.9
6.6/3.9
7” (17.8 cm)
10” (25.4 cm)
3.9
6.6/3.9
10” (25.4 cm)
10” (25.4 cm)
7.3
4.3/5.1
7” (17.8 cm)
10” (25.4 cm)
1.7/3.2
6.6/3.9
7” (17.8 cm)
10” (25.4 cm)
1.7/3.9
6.6/3.9
7” (17.8 cm)
10” (25.4 cm)
3.9
6.6/3.9
10” (25.4 cm)
10” (25.4 cm)
7.3
4.3/5.1
7” (17.8 cm)
10” (25.4 cm)
1.7/3.2
6.6/3.9
7” (17.8 cm)
10” (25.4 cm)
1.7/3.9
6.6/3.9
7” (17.8 cm)
10” (25.4 cm)
3.9
6.6/3.9
10” (25.4 cm)
10” (25.4 cm)
7.3
4.3/5.1
* A 1,200 CFM interior- or exterior-power ventilator should be used when installed over range/rangetop with gas char-grill.
** It is recommended that the 1,500 CFM ventilator be used with longer duct runs.
Note: Maximum amp rating for hoods includes recommended ventilator kit rating. All products must be hard wired with two-wire ground. An interior- or
exterior-power ventilator kit must be purchased for installation with all 18”H. hoods.
PLANNING AND DESIGN GUIDE
VIKINGRANGE.COM
•
1-888-VIKING1
REVISED 5/2/11
© 2 0 1 1 V R C — INFORMATION SUBJECT TO CHANGE
VENTILATION
Built-In Classic Chimney Wall Hood—
Standard, w/Ledge, & Ledgeless
✪ Installation Notes & Accessories
Recommended Ventilator Kits
•
•
•
•
See Installation Requirements table for recommendations for each hood model
One ventilator, one duct run for any size hood/ventilator
A 1,200 CFM interior or 1,500 CFM exterior (if applicable) ventilator should be used over ranges/rangetops with gas grill
Must use Viking ventilator kits with Viking hoods; use of non-Viking kits voids product warranty
Kit model
Description
Hood models
Approx. ship wt. lbs. (kg)
DIV300
300 CFM interior-power
DCWH3042/3644, DCWL3342/3944, &
15 (6.8)
DIV440
440 CFM interior-power
DCWN3042/3644
DCWH3042, DCWL3342, & DCWN3042
25 (11.3)
DIV600
600 CFM interior-power
DCWH3644/4244, DCWL3944/4544, &
27 (12.2)
43 (19.4)
39 (17.6)
DIV1200
1,200 CFM interior-power
DCWN3644/4244
DCWH4844, DCWN5144, & DCWN4844
DEV900
900 CFM exterior-power
DCWH3042/3642/4244, DCWL3342/3944/4544, &
DEV1200
1,200 CFM exterior-power
DEV1500
1,500 CFM exterior-power
DCWN3042/3644/4244
DCWH3042/3644/4244/4844, DCWL3342/3944/
4544/5144, & DCWN3042/3644/4244/4844
DCWH4844, DCWL5144, & DCWN4844
DIL900
900 CFM in-line power
DCWH3042/3642/4244, DCWL3342/3944/4544, &
20 (9.1)
DIL1200
1,200 CFM in-line power
DCWN3042/3644/4244
DCWH3042/3644/4244/4844, DCWL3342/3944/
4544/5144, & DCWN3042/3644/4244/4844
25 (11.3)
53 (23.9)
47 (21.3)
Duct Cover Extensions
•
•
•
•
•
For use with DCWH, DCWL, & DCWN hoods
Extends height of hood by up to 12” (for 10’ ceilings)
Replaces adjustable duct cover supplied with hood
Specify finish code following accessory model number (for example, DCCE1010-SS)
Available in Stainless Steel (SS), Black (BK), White (WH), Metallic Silver (MS), Graphite Gray (GG), Stone Gray (SG), Taupe
(TP), Biscuit (BT), Cotton White (CW), Oyster Gray (OG), Golden Mist (GM), Lemonade (LE), Sage (SA), Mint Julep (MJ),
Sea Glass (SE), Iridescent Blue (IB), Viking Blue (VB), Pumpkin (PM), Racing Red (RR), Apple Red (AR), Burgundy (BU), Plum
(PL), Chocolate (CH), and Cobalt Blue (CB).
Model
Description
Approx. ship wt. lbs. (kg)
DCCE1010
DCCE1210
DCCE1810
Duct cover extension (for 30” & 33”W. hoods—10”W. x 12”D. x 30” – 42”H.)
Duct cover extension (for 30”, 39”, 42”, & 45”W. hoods—12”W. x 12”D. x 28” – 40”H.)
Duct cover extension (for 48” & 51”W. hoods—18”W. x 12”D. x 28” – 40”H.)
4 (1.8)
6 (2.7)
8 (3.6)
Backsplashes
•
•
•
•
•
•
•
Stainless Steel (SS)
30”H.
Backsplashes protect the wall space below hood
Create a continuous finish between cooking surface and hood
Low maintenance, easy to clean
Hemmed edges with screw holes
Kit includes backsplash and fastening screws
Model
Description
Approx. ship wt. lbs. (kg)
BKS30
BKS36
BKS42
BKS48
BKS54
30”W.
36”W.
42”W.
48”W.
54”W.
7 (3.2)
9 (4.1
12 (5.4)
14 (6.3)
17 (7.7)
backsplash
backsplash
backsplash
backsplash
backsplash
PLANNING AND DESIGN GUIDE
VIKINGRANGE.COM
•
1-888-VIKING1
REVISED 5/2/11
© 2 0 1 1 V R C — INFORMATION SUBJECT TO CHANGE
VENTILATION
Built-In Classic Chimney Wall Hood—
Standard, w/Ledge, & Ledgeless
✪ Installation Notes & Accessories
Warming Shelf Panels
•
•
•
•
•
•
Stainless Steel (SS)
12”D./12”H.
Shelf panels hold cookware and condiments
Fold up/down, heavy-duty warming shelves (non-removable), factory installed on stainless steel backsplash
15-7/8”W. X 10-1/8”D.
Kit includes shelf (or shelves) and fastening screws
Model
Description
WGP30
WGP36
WGP42
WGP48
WGP54
30”W.
36”W.
42”W.
48”W.
54”W.
warming
warming
warming
warming
warming
Approx. ship wt. lbs. (kg)
shelf
shelf
shelf
shelf
shelf
panels
panels
panels
panels
panels
(one shelf)
(two shelves)
(two shelves)
(two shelves)
(two shelves)
9 (4.1)
12 (5.4)
14 (6.3)
16 (7.2)
20 (9.0)
Compliance Information
WARRANTY SUMMARY*
• Three-year full warranty—complete product (Professional and Designer)
• Five-year limited warranty—all ventilator motors (Professional and Designer)
• Ninety-day limited warranty—cosmetic parts such as glass, painted, and decorative items (Professional and Designer)
*Must use Viking ventilator kits with Viking hoods; use of non-Viking kits voids product warranty. For complete warranty see Use & Care Guide.
Warranty valid on Viking products shipped within the United States and Canada.
PLANNING AND DESIGN GUIDE
VIKINGRANGE.COM
•
1-888-VIKING1
REVISED 5/2/11
© 2 0 1 1 V R C — INFORMATION SUBJECT TO CHANGE