American Standard 6540.177.002 Monterrey 8 Inch Widespread Gooseneck Faucet, 8 Inch Spout Reach, 0.5 gpm Installation Instructions

Instructions

SPREAD LAVATORY

FAUCETS

6540.171

6540.177

6540.178

6540.179

6540.188

6542.177

6542.178

Thank you for selecting American-Standard...

the benchmark of fine quality for over 100 years.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

Recommended tools

Phillips Screwdriver Channel Locks Adjustable Wrench

1

SPOUT OR BASE ASSEMBLY

CAUTION

Turn off water at main supply.

Insert SPOUT SHANK (1) through center hole of mounting surface, making sure

RUBBER GASKET (2) is properly positioned in SPOUT BASE (3).

Assemble RUBBER WASHER (4), BRASS WASHER (5), and LOCKNUT (6) onto threads of

SPOUT SHANK (1) from underside of mounting surface.

Align SPOUT (7) and tighten LOCKNUT (6). Be sure slot in BRASS WASHER (5) is positioned to the rear as shown.

1a

TO CHANGE SPOUT TO A SWIVEL SPOUT:

Unscrew SPOUT NUT (8) and remove SPOUT (7).

Take SPOUT CLIP (9) off SPOUT (7) and remove RUBBER RING (10).

Replace RUBBER RING (10) with seperate PLASTIC RING (11) packed with faucet.

Put SPOUT CLIP (9) on SPOUT (7).

Reassemble SPOUT (7) to SPOUT BASE (3).

2

DRAIN ASSEMBLY (6542.177, 6542.178)

Apply a bead of PUTTY around underside of DRAIN PLUG (1) flange.

Insert DRAIN PLUG (1) into lavatory drain hole.

Hold DRAIN PLUG (1) to prevent turning and assemble GASKET (2),

WASHER (3) and LOCKNUT (4) from underneath sink. Tighten with adjustable wrench or channel locks.

PUTTY

1

Make sure SEAL (5) is inserted into bottom of DRAIN PLUG (1).

Insert threaded end of TAILPIECE

(6) into lower end of DRAIN

PLUG (1) and tighten.

LAVATORY

DRAIN

Connect other end to P-Trap.

2

3

4

5

3

2

1

6

Certified to comply with ANSI A112.18.1M

M965453 REV. 1.2 (7/15)

7

8

10

9

7

4

5

6

Tubing Cutter

11

3

VALVE ASSEMBLY

Install LOCKNUTS (1), BRASS WASHERS (2) and RUBBER WASHERS (3) onto valve shanks.

Push TUBING (4) ends into VALVE (5) side outlets. Insert VALVES (5) into mounting holes from underside of ledge.

Press TEE (6) onto SPOUT SHANK (7) making certain that the O-RING (8) is properly seated on SHANK (7). Push COUPLING (9) into TEE (6) and attach to SPOUT SHANK (7) and tighten.

Place RUBBER RING (11) into DECK ADAPTERS (10) and thread onto valves until snug against internal stop.

Tighten LOCKNUT (1) to secure VALVE (5) position.

10

11

3

Slide FERRULE (13) and COUPLING NUT (14) to outlet of VALVE (5) and tighten

COUPLING NUT (14) firmly.

10

5/16'' MIN.

11

5

MOUNTING SURFACE

2

1

HOT

3

2

1

4

4 MAKE WATER SUPPLY CONNECTIONS

NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE

PURCHASED SEPARATELY.

Connect water supply to FAUCET (1) with 1/2" IPS FLEXIBLE SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3).

Use adjustable wrench to tighten connections. Do not over tighten.

For BULL-NOSE RISERS (3), be careful not to kink copper supply when bending.

Use of tubing cutter may be required to cut to proper length.

2

1

5

13

14

10

11

MOUNTING

SURFACE

8

7

14

13

6

9

COUPLING

NUT

3

FERRULE

5

INSTALL HANDLES

Turn VALVES (6) to off position.

Insert ADAPTOR (4) with larger diameter over the VALVE STEM (5).

Align WRIST BLADE HANDLE (3) and install onto ADAPTOR (4).

Insert BLUE INDEX (2) into cold valve (right side) and red

INDEX (2a) into hot valve (left side).

Insert HANDLE SCREW (1) into

HANDLES and tighten with screwdriver.

COLD

5

4

5

6

1

2,2a

3

6

7

TEST INSTALLED FAUCET

Remove AERATOR.

With handle in OFF position, turn on water supplies and check all connections for leaks.

SERVICE STOP

WASHER

90°

To change direction of handle rotation, proceed as follows:

Turn valve to OFF position.

Remove HANDLE and BONNET NUT.

Remove SPRING CLIP.

Lift STOP WASHER, turn 90° and replace.

Replace SPRING CLIP.

Replace BONNET NUT, HANDLE, SCREW, and INDEX.

AERATOR may accumulate dirt causing distorted and reduced water flow. Remove AERATOR and rinse clean.

SPRING

CLIP

Operate both handles to flush water lines thoroughly. Check spout mounting and hose connections for leaks.

Turn handles into OFF position and replace AERATOR.

If spout drips, operate handles several times from OFF to ON position. Do not force - handles turn only 90°.

Plastic SCREEN in CARTRIDGE may accumulate dirt causing reduced water flow. To clean, first turn off hot and cold water supplies, then:

Remove HANDLE and BONNET NUT.

Remove CARTRIDGE by pulling up.

Thoroughly rinse plastic SCREEN at base of CARTRIDGE.

CARTRIDGE

Replace CARTRIDGE until flange is tight against valve body.

Turn valves OFF.

Replace BONNET NUT, HANDLE,

SCREW and INDEX.

SCREEN

CARE INSTRUCTIONS:

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A

CLOTH WITH A COARSE SURFACE.

M965453 REV. 1.2 (7/15)

051336-0020A

AERATOR

VANDAL PROOF KIT

SPREAD LAVATORY

FAUCETS

MODEL NUMBERS

6540.171

6540.177

6540.178

6540.179

6540.188

6542.177

6542.178

051211-0070A

INDEX KIT

051217-0020A

WRIST BLADE

HANDLE

904939-0020A

BONNET NUT

951764-0070A

CARTRIDGE

051212-0020A

ESCUTCHEON KIT

051213-0070A

VALVE MOUNTING KIT

024220-0070A

COUPLING NUT

M965453 REV. 1.2 (7/15)

M964463-YYY0A

AERATOR, (1.2 gpm)

066114-0020A

AERATOR, (0.5 gpm)

012087-0070A

SPOUT SEAL KIT

M950336-0020A

ROSE SPRAY

051322-0020A

VANDAL PROOF

SCREW

M918014-0070A

ADAPTER

012087-0070A

SPOUT SEAL KIT

M923207-0070A

FLOW RESTRICTOR

051336-0020A

AERATOR

VANDAL PROOF KIT

066114-0020A

AERATOR, (0.5 gpm)

M950336-0020A

ROSE SPRAY

012087-0070A

SPOUT SEAL KIT

M950284-0020A

ESCUTCHEON KIT

A911748-0070A

SPOUT GASKET

015025-0020A

DRAIN COMPLETE

030256-0070A

SPOUT MOUNTING KIT

012112-0070A

TUBE SEAL &

COUPLING KIT

012111-0070A

TUBE & TEE KIT

070532-0040A

TAILPIECE

033757-0070A

TEE MOUNTING KIT

Appropriate finish code

CHROME 002

HOT LINE FOR HELP

For toll-free information and answers to your questions, call:

1 (800) 442-1902

Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST

Saturday 10:00 a.m. to 4:00 p.m. EST

IN CANADA 1-800-387-0369

(TORONTO 1-905-306-1093)

Weekdays 8:00 a.m. to 7:00 p.m. EST

IN MEXICO 01-800-839-1200