TForce4 U AM2 Setup Manual
FCC Information and Copyright
This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.
The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.
Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.
The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.
Table of Contents
Chapter 1: Introduction.......................................... 1
1.1
1.2
1.3
1.4
1.5
Before You Start ................................................................................1
Package Checklist.............................................................................1
Motherboard Features......................................................................2
Rear Panel Connectors .....................................................................3
Motherboard Layout ........................................................................4
Chapter 2: Hardware Installation............................ 5
2.1
Installing Central Processing Unit (CPU) ......................................5
2.2
FAN Headers......................................................................................7
2.3
Installing System Memory ................................................................8
Connectors and Slots............................................................................................10
Chapter 3: Headers & Jumpers Setup.................... 12
3.1
3.2
How to Setup Jumpers ....................................................................12
Detail Settings..................................................................................12
4.1
4.2
4.3
5.1:
5.2:
5.3
Operation System............................................................................20
Raid Arrays ......................................................................................20
How RAID Works.............................................................................20
T-Power Introduction .....................................................................24
T-Power BIOS Feature ....................................................................25
T-Power Windows Feature ............................................................33
6.1
6.2
6.3
6.4
Driver Installation Note .................................................................42
Award BIOS Beep Code ..................................................................43
Extra Information ...........................................................................43
Troubleshooting...............................................................................45
Chapter 4: NVIDIA RAID Functions ...................... 20
Chapter 6: Useful Help .......................................... 42
Appendencies: SPEC In Other Language............... 46
German .................................................................................................................46
France....................................................................................................................48
Italian ....................................................................................................................50
Spanish ..................................................................................................................52
Portuguese............................................................................................................54
Polish .....................................................................................................................56
RUSSIAN ................................................................................................................58
ARABIC..................................................................................................................60
JAPANESE .............................................................................................................62
TForce4 U AM2
CHAPTER 1: INTRODUCTION
1.1
BEFORE YOU START
Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:
1.2
„
Prepare a dry and stable working environment with
sufficient lighting.
„
Always disconnect the computer from power outlet
before operation.
„
Before you take the motherboard out from anti-static
bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.
„
Avoid touching the components on motherboard or the
rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.
„
Do not leave any unfastened small parts inside the
case after installation. Loose parts will cause short
circuits which may damage the equipment.
„
Keep the computer from dangerous area, such as heat
source, humid air and water.
PACKAGE CHECKLIST
FDD Cable X 1
HDD Cable X 1
Serial ATA Cable X 1
Serial ATA Power Cable X 1
Rear I/O Panel for ATX Case X 1
User’s Manual X 1
Fully Setup Driver CD X 1
USB 2.0 Cable X1 (optional)
S/PDIF out Cable X 1 (optional)
1
Motherboard Manual
1.3
MOTHERBOARD FEATURES
SPEC
Socket AM2
CPU
AMD Athlon 64 / Athlon 64 FX / Althlon
64X2 / Sempron processors
FSB
Support HyperTransport
Chipset
nVIDIA nForce4 Ultra
Supports Hyper Transport and Cool=n=Quiet
Supports up to 1000 MHz Bandwidth
Environment Control initiatives,
ITE 8712F / 8716F
Super I/O
AMD 64 Architecture enables 32 and 64 bit computing
Provides the most commonly used legacy H/W Monitor
Super I/O functionality.
Fan Speed Controller
Low Pin Count Interface
ITE's "Smart Guardian" function
DIMM Slots x 4
Main
Each DIMM supports 256/512MB & 1GB
Memory
DDR2
Dual Channel Mode DDR2 memory module
Supports DDR2 400 / 533 / 667 / 800
Registered DIMM and Non-ECC DIMM is not supported
Max Memory Capicity 4GB
Integrated IDE Controller
IDE
Ultra DMA 33 / 66 / 100 / 133 Bus Master supports PIO Mode 0~4,
Mode
SATA
2
Integrated Serial ATA Controller
SATA Version 2.0 specification compliant.
Data transfer rates up to 3.0 Gb/s.
LAN
Realtek 8201CL PHY
Sound
ALC 655 / 658 (optional)
10 / 100 Mb/s Auto-Negotiation
6 channels audio out
AC 97 Version 2.3
PCI slot
x4
Supports PCI expansion cards
Slots
PCI Express x16 slot
x1
Supports PCI Express x16 expansion cards
PCI Express x 1 slot
x2
Supports PCI Express x1 expansion cards
On Board
Floppy connector
x1
Each connector supports 2 Floppy drives
Connector
Printer Port connector
x1
Each connector supports 1 Printer port
IDE Connector
x2
Each connector supports 2 IDE device
SATA Connector
x4
Each connector supports 1 SATA devices
Front Panel Connector
x1
Supports front panel facilities
Front Audio Connector
x1
Supports front panel audio function
CD-in Connector
x1
Supports CD audio-in function
S/PDIF out connector
x1
Supports digital audio out function
CPU Fan header
x1
CPU Fan power supply (with Smart Fan function)
System Fan header
x3
System Fan Power supply
Chassis open header (optional)
x1
For chassis intruder detection function
CMOS clear header
x1
Restore CMOS data to factory default
TForce4 U AM2
SPEC
USB connector
x3
Each connector supports 2 front panel USB ports
Power Connector (24pin)
x1
Connects to Power supply
Power Connector (4pin)
x1
Connects to Power supply
PS/2 Keyboard
x1
Connects to PS/2 Keyboard
x1
Connects to PS/2 Mouse
Back Panel Serial Port
PS/2 Mouse
x1
Provide RS-232 Serial connection
I/O
LAN port
x1
Connects to RJ-45 ethernet cable
USB Port
x4
Connects to USB devices
Audio Jack
x3
Provide Audio-In/Out and microphone connection
Board Size
218 x 293 (mm)
Special
NVIDIA nTunes
Features
RAID 0 / 1 / 0+1 / 5 support
Biostar Reserves the right to add or remove support for
OS Support Windows 2K / XP
1.4
any OS With or without notice.
REAR PANEL CONNECTORS
PS/2
Mouse
LAN
Line In
Line Out
Mic In
PS/2
Keyboard
COM1
COM2
(optional)
USBX2
USBX2
3
Motherboard Manual
1.5
MOTHERBOARD LAYOUT
JCFAN1
JKBMS1
JKBMSV1
JATXPWR2
JCOM1
(optional)
DDR2B2
DDR2A2
DDR2B1
JCOM2
DDR2A1
JPRNT1
JATXPWR1
JUSBV1
JUSB4
JUSBLAN1
LAN
JAUDIO1
JAUDIO1
PCI-EX16
JNFAN1
Codec
JDDRII_2.3V
PCI-EX1_1
nVIDIA
nForce4
PCI-EX1_2
JCDIN1
JUSB2
PCI2
JUSB4
BAT1
JSATA1 JSATA2 JSATA3 JSATA4
JUSBV2
JSPDIF_OUT1
BIOS
JUSB3
JCMOS1
PCI3
LED_D1
LED_D2
FDD1
PCI4
JPANEL1
RSTSW2 PWRSW1
Note: ■ represents the 1st pin.
4
IDE1
IDE2
PCI1
Super I/O
JSFAN2 JSFAN1
TForce4 U AM2
CHAPTER 2: HARDWARE INSTALLATION
2.1 INSTALLING CENTRAL PROCESSING UNIT (CPU)
Step 1: Remove the socket protection cap.
Step 2: Pull the lever toward direction A from the socket and then raise the
lever up to a 90-degree angle.
Step 3: Look for the white triangle on socket, and the gold triangle on
CPU should point towards this white triangle. The CPU will fit only
in the correct orientation.
5
Motherboard Manual
Step 4: Hold the CPU down firmly, and then close the lever toward direct
B to complete the installation.
Step 5: Put the CPU Fan on the CPU and buckle it. Connect the CPU
FAN power cable to the JCFAN1. This completes the installation.
6
TForce4 U AM2
2.2
FAN HEADERS
These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different according to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.
JCFAN1: CPU Fan Header
JCFAN1
1
3
Pin
1
2
3
Assignment
Ground
Smart Fan
Control
FAN RPM rate
sense
JSFAN1/ JSFAN2: System Fan Header
JNFAN1: North Bridge Fan Header
Pin
3
1
JNFAN1
3
1
2
3
Assignment
Ground
+12V
FAN RPM rate
sense
1
JSFAN2
JSFAN1
Note:
The JCFAN1、JSFAN1/JSFAN2 and JNFAN1 support 3-pin head connector. When
connecting with wires onto connectors, please note that the red wire is the positive and
should be connected to pin#2, and the black wire is Ground and should be connected to
GND.
7
Motherboard Manual
2.3
INSTALLING SYSTEM MEMORY
DDR2A1
DDR2B1
DDR2A2
DDR2B2
A. Memory Modules
8
1.
Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.
2.
Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.
TForce4 U AM2
B. Memory Capacity
C.
DIMM Socket
Location
DDR Module
DDR2A1
256MB/512MB/1024MB
DDR2B1
256MB/512MB/1024MB
DDR2A2
256MB/512MB/1024MB
DDR2B2
256MB/512MB/1024MB
Total Memory
Size
Max is 4GB.
Dual Channel Memory installation
To trigger the Dual Channel function of the motherboard, the memory module
must meet the following requirements:
Install memory module of the same density in pairs, shown in the following
table.
Dual Channel Status DDR2A1 DDR2B1 DDR2A2 DDR2B2
Enabled
O
O
X
X
Enabled
X
X
O
O
Enabled
O
O
O
O
(O means memory installed, X means memory not installed.)
The DRAM bus width of the memory module must be the same (x8 or
x16)
9
Motherboard Manual
CONNECTORS AND SLOTS
FDD1: Floppy Disk Connector
The motherboard provides a standard floppy disk connector that supports 360K,
720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the
provided floppy drive ribbon cables.
2
34
1
33
IDE1/IDE2: Hard Disk Connectors
The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO
Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality. It has two
HDD connectors IDE1 (primary) and IDE2 (secondary).
The IDE connectors can connect a master and a slave drive, so you can
connect up to four hard disk drives. The first hard drive should always be
connected to IDE1.
40
2
IDE2
10
39
1
IDE1
TForce4 U AM2
PCI-Ex16: PCI-Express x16 Slot
-
PCI-Express 1.0a compliant.
Maximum theoretical realized bandwidth of 4GB/s simultaneously per
direction, for an aggregate of 8GB/s totally.
PCI-Ex1_1/PCI-Ex1_2: PCI-Express x1 slots
-
PCI-Express 1.0a compliant.
Data transfer bandwidth up to 250MB/s per direction; 500MB/s in total.
PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.
2X bandwidth over the traditional PCI architecture.
PCI-EX16
PCI-EX1_1
PCI-EX1_2
PCI1~PCI4: Peripheral Component Interconnect Slots
This motherboard is equipped with 4 standard PCI slots. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.
PCI1
PCI2
PCI3
PCI4
11
Motherboard Manual
CHAPTER 3: HEADERS & JUMPERS SETUP
3.1
HOW TO SETUP JUMPERS
The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open”.
Pin opened
3.2
Pin closed
Pin1-2 closed
DETAIL SETTINGS
JPANEL1: Front Panel Header
This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, Sleep
button and speaker connection. It allows user to connect the PC case’s front
panel switch functions.
16 15
RST
+ -
PWR_LED
+ + -
On/Off
HLED
SPK
SLP
2 1
Pin
1
2
3
4
5
6
7
8
12
Assignment
+5V
N/A
N/A
Speaker
HDD LED (+)
HDD LED (-)
Ground
Reset control
Function
Speaker
Connector
Hard drive
LED
Reset button
Pin
9
10
11
12
13
14
15
16
Assignment
Sleep control
Ground
N/A
Power LED (+)
Power LED (+)
Power LED (-)
Power button
Ground
Function
Sleep button
N/A
Power LED
Power-on button
TForce4 U AM2
JATXPWR1: ATX Power Source Connector
This connector allows user to connect 24-pin power connector on the ATX
power supply.
13
1
24
12
Pin
Assignment
Pin
Assignment
13
14
15
16
17
18
19
20
21
22
23
24
+3.3V
-12V
Ground
PS_ON
Ground
Ground
Ground
NC
+5V
+5V
+5V
Ground
1
2
3
4
5
6
7
8
9
10
11
12
+3.3V
+3.3V
Ground
+5V
Ground
+5V
Ground
PW_OK
Standby Voltage+5V
+12V
+12V
+3.3V
JATXPWR2: ATX Power Source Connector
By connecting this connector, it will provide +12V to CPU power circuit.
1
2
3
4
Pin
1
2
3
4
Assignment
+12V
+12V
Ground
Ground
13
Motherboard Manual
JKBMSV1: Power Source Selection Headers for Keyboard/Mouse
Pin 1-2 Close:
JKBMSV1: +5V for PS/2 keyboard and mouse。
Pin 2-3 Close:
JKBMSV1: PS/2 keyboard and mouse are powered with +5V standby
voltage.
1
1
3
3
Pin 1-2 close
1
3
Pin 2-3 close
JUSB2/JUSB3/JUSB4: Headers for USB 2.0 Ports at Front Panel
This header allows user to connect additional USB cable on the PC front panel,
and also can be connected with internal USB devices, like USB card reader.
JUSB2 JUSB3 JUSB4
2
1
14
10
9
Pin
1
2
3
4
5
6
7
8
9
10
Assignment
+5V (fused)
+5V (fused)
USBUSBUSB+
USB+
Ground
Ground
Key
NC
TForce4 U AM2
JUSBV1/JUSBV2: Power Source Headers for USB Ports
Pin 1-2 Close:
JUSBV1: +5V for USB ports at JUSBLAN1.
JUSBV2: +5V for USB ports at front panel (JUSB1/JUSB2/JUSB3).
Pin 2-3 Close:
JUSBV1: USB ports at JUSBLAN1 are powered by +5V standby voltage.
JUSBV2: USB ports at front panel (JUSB1/JUSB2/JUSB3) are powered by
+5V standby voltage.
1
3
3
1
3
Pin 1-2 close
1
JUSBV1
1
1
3
3
3
1
JUSBV2
Pin 2-3 close
Note:
In order to support this function “Power-On system via USB device,” “JUSBV1/ JUSBV2”
jumper cap should be placed on Pin 2-3 individually.
JFAUDIO1: Front Panel Audio Header
This header allows user to connect the front audio output cable with the PC front
panel. It will disable the output on back panel audio connectors.
Pin
1
2
3
4
5
6
1
2
13
14
7
8
9
10
11
12
13
14
Assignment
Mic in/center
Ground
Mic power/Bass
Audio power
Right line out/
Speaker out Right
Right line out/
Speaker out Right
Reserved
Key
Left line out/
Speaker out Left
Left line out/
Speaker out Left
Right line in/
Rear speaker Right
Right line in/
Rear speaker Right
Left line in/
Rear speaker Left
Left line in/
Rear speaker Left
15
Motherboard Manual
JCDIN1: CD-ROM Audio-in Connector
This connector allows user to connect the audio source from the variaty devices,
like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc..
4
1
Pin
1
2
3
4
Assignment
Left Channel Input
Ground
Ground
Right Channel Input
JCMOS1: Clear CMOS Header
By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting
and the CMOS data, please carefully follow the procedures to avoid damaging
the motherboard.
1
3
Pin 1-2 Close:
Normal Operation (default).
1
1
3
3
Pin 2-3 Close:
Clear CMOS data.
※ Clear CMOS Procedures:
1.
2.
3.
4.
5.
6.
16
Remove AC power line.
Set the jumper to “Pin 2-3 close”.
Wait for five seconds.
Set the jumper to “Pin 1-2 close”.
Power on the AC.
Reset your desired password or clear the CMOS data.
TForce4 U AM2
JSATA1~JSATA4: Serial ATA Connectors
The motherboard has a PCI to SATA Controller with 4 channels SATA interface,
it satisfies the SATA 2.0 spec and with transfer rate of 3.0 Gb/s.
JSATA1 JSATA2 JSATA3 JSATA4
1
4
Pin
1
2
3
4
5
6
7
Assignment
Ground
TX+
TXGround
RXRX+
Ground
7
JPRNT1: Printer Port Connector
This header allows you to connector printer on the PC.
25
2
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
Assignment
-Strobe
-ALF
Data 0
-Error
Data 1
-Init
Data 2
-Scltin
Data 3
Ground
Data 4
Ground
Data 5
1
Pin
14
15
16
17
18
19
20
21
22
23
24
25
Assignment
Ground
Data 6
Ground
Data 7
Ground
-ACK
Ground
Busy
Ground
PE
Ground
SCLT
17
Motherboard Manual
Header for Memory Voltage Overclocking: JDDRII_2.3V
When processing Memory Voltage Overclocking, please place the jumper to
pin1-2 Closed. The Default setting is Pin 2-3 Closed.
1
3
Pin 1-2 Close:
Memory voltage 2.3V.
3
1
1
3
Pin 2-3 Close:
Normal status (default).
Note:
1.
When “JDDRII_2.3V” jumper cap is placed on Pin 2-3, memory voltage
can be manually adjusted under CMOS setup.
2.
When “JDDRII_2.3V” jumper cap is placed on Pin 1-2, memory voltage
will be fixed at 2.3V automatically, and can’t be adjusted under COMS
setup.
Before setting memory voltage overclocking, please ensure that your DDR
supports up to 2.3V. (Consulting your DDR supplier)
On-Board LED Indicators
There are 2 LED indicators on the motherboard to show system status.
LED_D1
LED_D2
LED_D1 and LED_D2:
These 2 LED indicate system power on diagnostics.
Please refer to the table below for different messages:
LED_D1
ON
ON
OFF
OFF
18
LED_D2
ON
OFF
ON
OFF
Message
Normal
Memory Error
VGA Error
Abnormal: CPU / Chipset error.
TForce4 U AM2
On-Board Buttons (optional)
There are 2 on-board buttons.
PWRSW RSTSW
(Optional) (Optional)
PWRSW1:
This is an on-board Power Switch button.
RSTSW2:
This is an on-board Reset button.
JSPDIF_OUT1: Digital Audio-out Connector
This connector allows user to connect the PCI bracket SPDIF output header.
Pin
1
2
3
3
Assignment
+5V
SPDIF_OUT
Ground
1
19
Motherboard Manual
CHAPTER 4: NVIDIA RAID FUNCTIONS
4.1
z
OPERATION SYSTEM
Supports Windows XP Home/Professional Edition, and Windows 2000 Professional.
4.2
RAID ARRAYS
NVRAID supports the following types of RAID arrays:
RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for
many applications.
RAID 1: RAID 1 defines techniques for mirroring data.
RAID 0+1: RAID 0+1 combines the techniques used in RAID 0 and RAID 1.
Spanning (JBOD): JBOD provides a method for combining drives of different sizes in to
one large disk.
RAID 5: RAID 5 provides fault tolerance and better utilization of disk capacity.
4.3
HOW RAID WORKS
RAID 0:
The controller “stripes” data across multiple drives in a RAID 0 array system. It breaks
up a large file into smaller blocks and performs disk reads and writes across multiple
drives in parallel. The size of each block is determined by the stripe size parameter,
which you set during the creation of the RAID set based on the system environment. This
technique reduces overall disk access time and offers high bandwidth.
Features and Benefits
­
­
­
­
­
Drives: Minimum 1, and maximum is up to 6 or 8. Depending on the
platform.
Uses: Intended for non-critical data requiring high data throughput, or any
environment that does not require fault tolerance.
Benefits: provides increased data throughput, especially for large files. No
capacity loss penalty for parity.
Drawbacks: Does not deliver any fault tolerance. If any drive in the array
fails, all data is lost.
Fault Tolerance: No.
Block 1
Block 3
Block 5
20
Block 2
Block 4
Block 6
TForce4 U AM2
RAID 1:
Every read and write is actually carried out in parallel across 2 disk drives in a RAID 1
array system. The mirrored (backup) copy of the data can reside on the same disk or on
a second redundant drive in the array. RAID 1 provides a hot-standby copy of data if
the active volume or drive is corrupted or becomes unavailable because of a hardware
failure.
RAID techniques can be applied for high-availability solutions, or as a form of
automatic backup that eliminates tedious manual backups to more expensive and less
reliable media.
Features and Benefits
­
­
­
­
­
Drives: Minimum 2, and maximum is 2.
Uses: RAID 1 is ideal for small databases or any other application that
requires fault tolerance and minimal capacity.
Benefits: Provides 100% data redundancy. Should one drive fail, the
controller switches to the other drive.
Drawbacks: Requires 2 drives for the storage space of one drive.
Performance is impaired during drive rebuilds.
Fault Tolerance: Yes.
Block 1
Block 2
Block 3
Block 1
Block 2
Block 3
21
Motherboard Manual
RAID 0+1:
RAID 0 drives can be mirrored using RAID 1 techniques. Resulting in a RAID 0+1
solution for improved performance plus resiliency.
Features and Benefits
-
-
Drives: Minimum 4, and maximum is 6 or 8, depending on the platform.
Benefits: Optimizes for both fault tolerance and performance, allowing for
automatic redundancy. May be simultaneously used with other RAID
levels in an array, and allows for spare disks.
Drawbacks: Requires twice the available disk space for data redundancy,
the same as RAID level 1.
Fault Tolerance: Yes.
Block 1
Block 3
Block 5
Block 2
Block 4
Block 6
Block 1
Block 3
Block 5
Block 2
Block 4
Block 6
Spanning (JBOD):
JBOD stands for “Just a Bunch of Disks”. Each drive is accessed as if it were on a
standard SCSI host bus adapter. This is useful when a single drive configuration is
needed, but it offers no speed improvement or fault tolerance.
Features and Benefits
-
Uses: JBOD works best if you have odd sized drives and you want to
combine them to make one big drive.
Benefits: JBOD provides the ability to combine odd size drives using all of
the capacity of the drives.
Drawbacks: Decreases performance because of the difficulty in using
drives concurrently.
Fault Tolerance: Yes.
Single Logical
Drive
22
Disk 1: 40GB
Disk 2: 80GB
Disk 3: 40GB
Disk 4: 120GB
TForce4 U AM2
RAID 5:
RAID 5 stripes both data and parity information across three or more drives. It writes
data and parity blocks across all the drives in the array. Fault tolerance is maintained
by ensuring that the parity information for any given block of data is placed on a
different drive from those used to store the data itself.
Features and Benefits
Drives: Minimum 3.
Uses: RAID 5 is recommended for transaction processing and
general purpose service.
Benefits: An ideal combination of good performance, good fault
tolerance, and high capacity and storage efficiency.
Drawbacks: Individual block data transfer rate same as a single disk.
Write performance can be CPU intensive.
Fault Tolerance: Yes.
Disk 1
DATA 1
DATA 3
PARITY
DATA 7
DATA 9
PARITY
Disk 2
Cbipset name
DATA 2
PARITY
DATA 5
DATA 8
PARITY
DATA 11
Disk 3
PARITY
DATA 4
DATA 6
PARITY
DATA 10
DATA 12
※
For more detailed setup information, please refer to the Driver CD, or go to
http://www.nvidia.com/page/pg_20011106217193.html to download NVIDIA nForce Tutorial
Flash.
23
Motherboard Manual
CHAPTER 5: OVERCLOCK QUICK GUIDE
5.1:
T-POWER INTRODUCTION
Biostar T-Power is a whole new utility that is designed for overclock users.
Based on many precise tests, Biostar Engineering Team (BET) has
developed this ultimate overclock engine to raise system performance.
No matter whether under BIOS or Windows interface, T-Power is able to
present the best system state according to users’ overclock setting.
T-Power BIOS Features:
Overclocking Navigator Engine (O.N.E.)
CMOS Reloading Program (C.R.P.)
Memory Integration Test (M.I.T., under Overclock Navigator Engine)
Integrated Flash Program (I.F.P.)
Smart Fan Function (under PC Health Status)
Self Recovery System (S.R.S)
T-Power Windows Feature:
Hardware Monitor
Overclock Engine
Smart Fan Function
Life Update
24
TForce4 U AM2
5.2: T-POWER BIOS FEATURE
A. Overclocking Navigator Engine (O.N.E.):
ONE provides two powerful overclocking engines: MOS and AOS for both
Elite and Casual overclockers.
Manual Overclock System (M.O.S.)
MOS is designed for experienced overclock users.
It allows users to customize personal overclock settings.
25
Motherboard Manual
CPU Overclock Setting:
CPU Voltage:
This function will increase CPU stability when overclocking. However, the
CPU temperature will increase when CPU voltage is increased.
Choices: The adjustable range is from 0.800V to 2.310V.
CPU Frequency:
CPU Frequency is directly in proportion to system performance. To
maintain the system stability, CPU voltage needs to be increased also
when raising CPU frequency.
Choices: This range is from 200 to 450, with an interval of 1MHz.
Memory Overclock Setting:
Memory Voltage:
This function will increase memory stability when overclocking.
Choices: The range is from 1.800V to 2.100V, with an interval of 0.100V.
Memclock Frequency:
To get better system performance, sometimes downgrading the memory
frequency is necessary when CPU frequency is adjusted over the upper
limit.
Choices: DDR2 400, DDR2 533, DDR2 667, DDR2 800 (MHz).
PCI-Express Overclock Setting:
PCIE Clock:
It helps to increase VGA card performance.
Choices: The range is from 100 to 145, with an interval of 1MHz.
Chipset Overclock Setting:
Chipset Voltage Regulator:
This function will increase chipset stability when overclocking.
Choices: 1.550V, 1.600V, 1.650V, 1.700V.
HT Frequency:
We recommend users to set this item at “x4” when overclocking.
Choices: x1, x2, x3, x4, x5, Auto.
26
TForce4 U AM2
Automatic Overclock System (A.O.S.)
For beginners in overclock field, BET had developed an easy, fast, and
powerful feature to increase the system performance, named A.O.S.
Based on many tests and experiments, A.O.S. provides 3 ideal overclock
configurations that are able to raise the system performance in a single
step.
V6 Tech Engine:
This setting will raise about 10%~15% of whole system performance.
V8 Tech Engine:
This setting will raise about 15%~25% of whole system performance.
V12 Tech Engine:
This setting will raise about 25%~30% of whole system performance.
27
Motherboard Manual
Notices:
1.
Not all types of AMD CPU perform above overclock setting ideally; the difference will be based
on the selected CPU model.
2.
From BET experiments, the Atholon64 FX CPU is not suitable for this A.O.S. feature.
B. CMOS Reloading Program (C.R.P.):
It allows users to save different CMOS settings into BIOS-ROM.
Users are able to reload any saved CMOS setting for customizing system
configurations.
Moreover, users are able to save an ideal overclock setting during overclock
operation.
There are 50 sets of record addresses in total, and users are able to name the
CMOS data according to personal preference.
28
TForce4 U AM2
C. Memory Integration Test (M.I.T.):
This function is under “Overclocking Navigator Engine” item.
MIT allows users to test memory compatibilities, and no extra devices or
software are needed.
Step 1:
The default setting under this item is “Disabled”; the condition parameter should
be changed to “Enable” to proceed this test.
↓
Step 2:
Save and Exit from CMOS setup and reboot the system to activate this test.
Run this test for 5 minutes (minimum) to ensure the memory stability.
Step 3:
When the process is done, change the setting back from “Enable” to “Disable”
to complete the test.
29
Motherboard Manual
D. Self Recovery System (S.R.S.):
This function can’t be seen under T-Power BIOS setup; and is always on
whenever the system starts up.
However, it can prevent system hang-up due to inappropriate overclock
actions.
When the system hangs up, S.R.S. will automatically log in the default BIOS
setting, and all overclock settings will be re-configured.
E. Integrated Flash Program (I.F.P.):
IFP is a safe and quick way to upgrade BIOS.
Step 1:
Go to Biostar website (http://www.biostar.com.tw) to download the latest BIOS
file. Then, save the file into a floppy disk.
Step 2:
Insert the floppy disk and reboot the system to get into CMOS screen.
Step 3:
Select the item “Integrated Flash Program” to get the following frame and
choose the BIOS file downloaded in step 1.
Step 4:
Press “Enter” key to start BIOS file loading, and BIOS updating will process
automatically.
Step 5:
When the BIOS update is completed, press YES to the message “Flash done,
Reset system”, and the system will reboot automatically to finish the process.
Advise:
You can update the system BIOS by simply pressing “Enter” key for three times.
30
TForce4 U AM2
F. Smart Fan Function:
Smart Fan Function is under “PC Health Status”.
This is a brilliant feature to control CPU Temperature vs. Fan speed.
When enabling Smart Fan function, Fan speed is controlled automatically by
CPU temperature.
This function will protect CPU from overheat problem and maintain the system
temperature at a safe level.
↓
CPU Fan Off <℃>:
If the CPU temperature is lower than the set value, the CPU fan will turn
off. The range is from 0℃~127℃, with an interval of 1℃.
Choices: 16℃ (default).
CPU Fan Start <℃>
The CPU fan starts to work when CPU temperature arrives to this set
value. The range is from 0℃~127℃, with an interval of 1℃.
Choices: 32℃ (default).
CPU Fan Full speed <℃>
When CPU temperature arrives to the set value, the CPU fan will work
under Full Speed. The range is from 0℃~127℃, with an interval of 1℃.
Choices: 52℃ (default).
31
Motherboard Manual
Start PWM Value
When CPU temperature arrives to the set value, the CPU fan will work
under Smart Fan Function mode. The range is from 0~127, with an
interval of 1.
Choices: 32 (default).
Slope PWM
Choices: 1 PWM Value/℃ (default), 2 PWM Value/℃, 4 PWM Value/℃, 8
PWM Value/℃, 16 PWM Value/℃, 32 PWM Value/℃, 64PWM Value/℃.
S1: CPU temperature is 60℃, and PWM value is 1 PWM/℃.
S2: CPU temperature is 60℃, and PWM value is 2 PWM/℃.
S3: CPU temperature is 60℃, and PWM value is 3 PWM/℃.
Increasing the value of slope PWM will raise the speed of CPU fan.
As in above diagram, when the CPU temperature reaches 60℃, the CPU
fan speed for 3 PWM/℃ is higher than 1 PWM/℃ (S1<S2<S3).
32
TForce4 U AM2
5.3
T-POWER WINDOWS FEATURE
A.Hardware Monitor:
T-Power Hardware monitor allows users to monitor system voltage,
temperature and fan speed accordingly.
Additionally, a rescue action will be taken by the program automatically
while the system faces an abnormal condition. The program will trigger an
alarm or shut down the system when unpredictable errors occur.
All the monitoring items are illustrated by a waveform diagram.
Hardware Monitor Toolbar
i. Start-up Setting
Click on this item to run Hardware Monitor Program when the Windows
starts-up.
ii. Dialogue-Box Setting
Click on this item to pop-up warning dialogue-box when PC system is
abnormal.
iii. Exit
Click on this item to exit Hardware Monitor Program.
iv. Hide
Click on this item to hide this program in system tray. When hiding the
program, there will be a check icon in the system tray.
33
Motherboard Manual
CPU Temperature
This column configures the CPU temperature. There is a waveform to
represent the status of CPU temperature.
By adjusting
, users can easily configure the upper limit of CPU
temperature for system operating.
In this diagram, the white line represents the upper limit which user-set for CPU
temperature and the green line shows present CPU temperature.
If the CPU temperature is higher than the upper limit, the status line color will
change from green to red, and a warning sound will alert you. Also, the system
would change to
.
tray icon
FAN Speed
By adjusting
, users can easily configure the lower limit of the fan speed.
In this diagram, the green line shows present CPU Fan speed, and the yellow
line shows System Fan speed (if any).
If any one of the fans speeds is lower than the set value, the status line will
change into a red warning line, and the program will trigger an alarm system
would change to
.
automatically. Also, the system tray icon
34
TForce4 U AM2
CPU/Battery Voltage
i. VCore
This item displays the CPU voltage, represented by a light blue line.
to monitor the
Users can set the upper and lower limit by adjusting
CPU operating voltage.
If CPU voltage is higher or lower than the set value, the status line will
change into a red warning line, and a warning sound will alert you. Also,
will change to
.
the system tray icon
ii. VBAT
This item displays the CMOS battery voltage, represented by a light green
line.
to monitor the
Users can set the upper and lower limit by adjusting
status of battery voltage.
If battery voltage is higher or lower than the set value, the status line will
change to a red warning line, and a warning sound will alert you. Also, the
will change to
.
system tray icon
Reference data
This column represents the status of power supply voltage and cannot be
adjusted, it is only for present status reference.
35
Motherboard Manual
B. Overclocking Configurations
This diagram is designed for T-series
Overclocking utility. Friendly interface and solid
overclock features are the major concept of this
utility.
Graphic 1 will appear when activating this utility.
Graphic 1
A.
B.
C.
D.
E.
F.
Graphic 2
G.
H.
Clicking on “Biostar” will lead you to the
Biostar Homepage.
This column shows the CPU speed
information.
Click on this button and the utility will
pop-up 4 sub-screens (Please refers to
Graphic 3).
Click on this button to minimize this
program to taskbar.
This column shows present CPU speed
and overclocking percentage.
Clicking on this button will make the
program start up as soon as the
Windows starts up.
Click on this button to exit this overclock
utility.
Click on this button to reset all the
overclock features to default setting.
By adjusting
the
overclocking
features in 4 sub-screens, users can
tune the system performance to an
optimal level.
Graphic 3
36
TForce4 U AM2
CPU Overclocking Settings:
can configure three items
By adjusting
for CPU overclocking.
A.
CPU Frequency
Range: 200MHz~450MHz.
Interval: 1MHz.
B.
CPU Ratio
Range: 4~25.
Interval: 1.
C.
CPU Voltage
Range: 0.8V~2.0V.
Interval: 0.0125V.
Memory Overclocking Settings:
By adjusting
can configure two items for
Memory overclocking.
A. Memory Clock Frequency
Choices: 100, 133, 200, 266, 333, 400, 533,
667, 800.
B. Memory Voltage
Range: 1.8V~2.8V.
Interval: 0.1V.
AGP/PCI-Express Overclocking Setting:
can configure VGA card
By adjusting
overclocking. And this function helps to
increase VGA card performance.
Range: 100MHz~150MHz.
Interval: 1MHz.
37
Motherboard Manual
PCI Overclocking Setting:
This diagram shows present PCI working
status and helps to monitor PCI peripherals
working status.
This item cannot be adjusted.
38
TForce4 U AM2
C. Smart Fan Function
When Smart Fan Function is activated, screens will pop-up to illustrate
the fan speed information.
i.
CPU Temperature:
Show current CPU temperature.
ii.
CPU Fan speed:
Show current CPU Fan speed.
iii. System Fan speed:
Show current system Fan speed.
iv. Calibrate:
When changing CPU Fan or System Fan, click on this button to
re-calibrate the Fan speed.
Note:
1.
2.
When Smart Fan Function activates for the first time, this calibrate function would
auto-run to get upper and lower limitation of CPU Fan and System Fan.
When calibrating process is done, the calibrating window will auto-close, and the
main screen will show new fan speed data.
39
Motherboard Manual
v.
Auto:
If the green indicator is lit up, the Smart Fan Function is “On”
(Default Setting).
Click on this button again to close Smart Fan Function, and a
screen as below would pop-up.
There will be pulling-meter besides the CPU Fan and System Fan,
the CPU Fan and the System Fan speed can be adjusted by
adjusting the Cursor Up or Down.
vi. Program Tool Bar:
40
z
About:
Click on this button to get program-related information.
z
Minimize:
Click on this button to minimize the program to system tray
z
Exit:
Click on this button to exit this program.
TForce4 U AM2
D. Live Update
When Live Update program is activated, a screen will pop up to illustrate
BIOS related information.
i.
Link to Internet:
Click on this button will link to Biostar website and BIOS file will
be downloaded.
ii.
Update BIOS:
Click on this button to run BIOS flashing process, and it’s easy
and safe.
iii. Backup BIOS:
Click on this button, and BIOS file will be saved into the
user-selected folder.
iv. Clear CMOS:
Click on this item will clear the CMOS Data. When carrying this
job, the previous CMOS data would be cleared and returned to
default setting.
41
Motherboard Manual
CHAPTER 6: USEFUL HELP
6.1
DRIVER INSTALLATION NOTE
After you installed your operating system, please insert the Fully Setup
Driver CD into your optical drive and install the driver for better system
performance.
You will see the following window after you insert the CD
The setup guide will auto detect your motherboard and operating system.
Note:
If this window didn’t show up after you insert the Driver CD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.
A. Driver Installation
To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.
B. Software Installation
To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.
C. Manual
Aside from the paperback manual, we also provide manual in the Driver
CD. Click on the Manual icon to browse for available manual.
Note:
You will need Acrobat Reader to open the manual file. Please download the latest version
of Acrobat Reader software from
http://www.adobe.com/products/acrobat/readstep2.html
42
TForce4 U AM2
6.2
AWARD BIOS BEEP CODE
Beep Sound
Meaning
One long beep followed by two short
beeps
Video card not found or video card
memory bad
High-low siren sound
CPU overheated
System will shut down automatically
One Short beep when system boot-up No error found during POST
Long beeps every other second
6.3
No DRAM detected or install
EXTRA INFORMATION
A. BIOS Update
After you fail to update BIOS or BIOS is invaded by virus, the
Boot-Block function will help to restore BIOS. If the following message
is shown after boot-up the system, it means the BIOS contents are
corrupted.
In this Case, please follow the procedure below to restore the BIOS:
1. Make a bootable floppy disk.
2. Download the Flash Utility “AWDFLASH.exe” from the Biostar
website: www.biostar.com.tw
3. Confirm motherboard model and download the respectively BIOS
from Biostar website.
4. Copy “AWDFLASH.exe” and respectively BIOS into floppy disk.
5. Insert the bootable disk into floppy drive and press Enter.
6. System will boot-up to DOS prompt.
7. Type “Awdflash xxxx.bf/sn/py/r” in DOS prompt.
(xxxx means BIOS name.)
8. System will update BIOS automatically and restart.
9. The BIOS has been recovered and will work properly.
43
Motherboard Manual
B. CPU Overheated
If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.
When the CPU is over heated, the motherboard will shutdown
automatically to avoid a damage of the CPU, and the system may not
power on again.
In this case, please double check:
1. The CPU cooler surface is placed evenly with the CPU surface.
2. CPU fan is rotated normally.
3. CPU fan speed is fulfilling with the CPU speed.
After confirmed, please follow steps below to relief the CPU protection
function.
1. Remove the power cord from power supply for seconds.
2. Wait for seconds.
3. Plug in the power cord and boot up the system.
Or you can:
1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)
2. Wait for seconds.
3. Power on the system again.
44
TForce4 U AM2
6.4
TROUBLESHOOTING
Probable
1.
2.
Solution
No power to the system at all
1.
Power light don’t illuminate, fan
inside power supply does not turn 2.
on.
3.
Indicator light on keyboard does
not turn on.
System inoperative. Keyboard lights
are on, power indicator lights are lit,
and hard drive is spinning.
Make sure power cable is
securely plugged in.
Replace cable.
Contact technical support.
Using even pressure on both ends of
the DIMM, press down firmly until the
module snaps into place.
System does not boot from hard disk
1.
drive, can be booted from optical drive.
2.
System only boots from optical drive. 1.
Hard disk can be read and applications
can be used but booting from hard disk 2.
is impossible.
Check cable running from disk to
disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.
Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.
Back up data and applications
files.
Reformat the hard drive.
Re-install applications and data
using backup disks.
Screen message says “Invalid
Configuration” or “CMOS Failure.”
Review system’s equipment. Make sure
correct information is in setup.
Cannot boot system after installing
second hard drive.
1.
2.
Set master/slave jumpers
correctly.
Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.
45
Motherboard Manual
Appendencies: SPEC In Other Language
GERMAN
Spezifikationen
Sockel AM2
CPU
Die AMD 64-Architektur unterstützt eine 32-Bit- und
AMD Athlon 64 / Athlon 64 FX / Althlon 64-Bit-Datenverarbeitung
64X2/ Sempron Prozessoren
FSB
Chipsatz
Super E/A
Unterstützt Hyper Transport und Cool’n’Quiet
Unterstützt HyperTransport mit einer
Bandbreite von bis zu 1000 MHz
nVIDIA nForce4 Ultra
ITE 8712F / 8716F
Umgebungskontrolle,
Bietet die häufig verwendeten alten
Hardware-Überwachung
Super E/A-Funktionen.
Lüfterdrehzahl-Controller
Low Pin Count-Schnittstelle
"Smart Guardian"-Funktion von ITE
DDR2 DIMM-Steckplätze x 4
Arbeitsspeich Jeder DIMM unterstützt 256/512MB &
er
1GB DDR2.
SATA
LAN
Audio-Codec
Steckplätze
Unterstützt DDR2 400 / 533 / 667 / 800 registrierte
DIMMs. Nicht-ECC DIMMs werden nicht unterstützt.
Max. 4GB Arbeitsspeicher
IDE
Dual-Kanal DDR2 Speichermodul
Ultra DMA 33 / 66 / 100 / 133 Bus Master-Modus
Integrierter IDE-Controller
Unterstützt PIO-Modus 0~4,
Integrierter Serial ATA-Controller
Konform mit der SATA-Spezifikation Version 2.0.
Datentransferrate bis zu 3.0 Gb/s
10 / 100 Mb/s Auto-Negotiation
Realtek 8201CL PHY
Halb-/ Vollduplex-Funktion
ALC 655 / 658 (optional)
AC’97 Version 2.3
6-Kanal-Audioausgabe
S/PDIF-Ausgang
PCI-Steckplatz
x4
PCI Express x16 Steckplatz
x1
PCI Express x 1-Steckplatz
x2
Onboard-Ans Diskettenlaufwerkanschluss
x1 Jeder Anschluss unterstützt 2 Diskettenlaufwerke
chluss
Druckeranschluss Anschluss
x1 Jeder Anschluss unterstützt 1 Druckeranschluss
IDE-Anschluss
x2 Jeder Anschluss unterstützt 2 IDE-Laufwerke
SATA-Anschluss
x4 Jeder Anschluss unterstützt 1 SATA-Laufwerk
Fronttafelanschluss
x1 Unterstützt die Fronttafelfunktionen
46
Front-Audioanschluss
x1 Unterstützt die Fronttafel-Audioanschlussfunktion
CD-IN-Anschluss
x1 Unterstützt die CD Audio-In-Funktion
S/PDIF-Ausgangsanschluss
x1 Unterstützt die digitale Audioausgabefunktion
TForce4 U AM2
Spezifikationen
CPU-Lüfterstromversorgungsanschluss (mit Smart
CPU-Lüfter-Sockel
x1
System-Lüfter-Sockel
x3 System-Lüfter-Stromversorgungsanschluss
Fan-Funktion)
"Gehäuse offen"-Sockel (optional)
x1 Zur Erkennung eines geöffneten Gehäuses
"CMOS löschen"-Sockel
x1
USB-Anschluss
x3 Jeder Anschluss unterstützt 2
Stromanschluss (24-polig)
x1
Stromanschluss (4-polig)
x1
Fronttafel-USB-Anschlüsse
PS/2-Tastatur
x1
PS/2-Maus
x1
Rückseiten-E Serieller Anschluss
/A
Platinengröße
.
x1
LAN-Anschluss
x1
USB-Anschluss
x4
Audioanschluss
x3
218 mm (B) X 293 mm (L)
Sonderfunkti NVIDIA nTunes
onen
OS-Unterstüt
zung
Unterstützt RAID 0 / 1 / 0+1 / 5
Biostar behält sich das Recht vor, ohne Ankündigung die
Windows 2K / XP
Unterstützung für ein Betriebssystem hinzuzufügen
oder zu entfernen.
47
Motherboard Manual
FRANCE
SPEC
Socket AM2
UC
Processeurs AMD Athlon 64 / Athlon 64 FX
/ Althlon 64X2 / Sempron
Bus frontal
Chipset
Super E/S
L'architecture AMD 64 permet le calcul 32 et 64 bits
Prend en charge Hyper Transport et Cool’n’Quiet
Prend en charge Hyper Transport jusqu'à
une bande passante de 1000 MHz
nVIDIA nForce4 Ultra
ITE 8712F / 8716F
Initiatives de contrôle environnementales,
Fournit la fonctionnalité de Super E/S
Moniteur de matériel
patrimoniales la plus utilisée.
Contrôleur de vitesse de ventilateur
Interface à faible compte de broches
Fonction "Gardien intelligent" de l'ITE
Fentes DDR2 DIMM x 4
Module de mémoire DDR2 à mode à double voie
Mémoire
Chaque DIMM prend en charge des DDR2 Prend en charge la DDR2 400 / 533 / 667 / 800
principale
de 256/512 Mo et 1Go
IDE
SATA
LAN
Les DIMM à registres et DIMM sans code correcteurs
Capacité mémoire maximale de 4 Go
d'erreurs ne sont pas prises en charge
Contrôleur IDE intégré
Mode principale de Bus Ultra DMA 33 / 66 / 100 / 133
Prend en charge le mode PIO 0~4,
Contrôleur Serial ATA intégré :
Conforme à la spécification SATA Version 2.0
Taux de transfert jusqu'à 3.0 Go/s.
10 / 100 Mb/s négociation automatique
Realtek 8201CL PHY
Half / Full duplex capability
Sortie audio à 6 voies
Codec audio ALC 655 / 658 (optional)
AC’97 Version 2.3
Sortie (entrée) S/PDIF
Fentes
Connecteur
embarqué
Fente PCI
x4
Slot PCI Express x16
x1
Slot PCI Express x 1
x2
Connecteur de disquette
x1
Connecteur de Port d'imprimante
x1
Connecteur IDE
x2
Connecteur SATA
x4
Connecteur du panneau avant
x1
Chaque connector prend en charge 2 lecteurs de
disquettes
Chaque connector prend en charge 1 Port d'imprimante
Chaque connecteur prend en charge 2 périphériques
IDE
Chaque connecteur prend en charge 1 périphérique
SATA
Prend en charge les équipements du panneau avant
Connecteur Audio du panneau avantx1 x1 Prend en charge la fonction audio du panneau avant
Connecteur d'entrée CD
48
x1
Prend en charge la fonction d'entrée audio de CD
TForce4 U AM2
SPEC
Connecteur de sortie S/PDIF
x1
Embase de ventilateur UC
x1
Embase de ventilateur système
x3
Embase d'ouverture de châssis
x1
(optional)
Embase d'effacement CMOS
x1
Connecteur USB
x3
Connecteur d'alimentation
x1
Prend en charge la fonction de sortie audio numérique
Alimentation électrique du ventilateur UC (avec
fonction de ventilateur intelligent)
Alimentation électrique du ventilateur système
Pour la fonction de détection d'intrus dans le châssis
Chaque connecteur prend en charge 2 ports USB de
panneau avant
(24 broches)
Connecteur d'alimentation
x1
(4 broches)
E/S du
panneau
arrière
Dimensions
de la carte
Fonctionnali
tés
spéciales
Clavier PS/2
x1
Souris PS/2
x1
Port série
x1
Port LAN
x1
Port USB
x4
Fiche audio
x3
218 mm (l) X 293 mm (H)
NVIDIA nTunes
Prise en charge RAID 0 / 1 / 0+1
Support SE Windows 2K / XP
Biostar se réserve le droit d'ajouter ou de supprimer le
support de SE avec ou sans préavis.
49
Motherboard Manual
ITALIAN
SPECIFICA
L’architettura AMD 64 abilita la computazione 32
Socket AM2
CPU
Processori AMD Athlon 64 / Athlon 64 e 64 bit
FX / Althlon 64X2 / Sempron
FSB
Chipset
Supporto di Hyper Transport e Cool’n’Quiet
Supporto di HyperTransport fino a
1000 MHz di larghezza di banda
nVIDIA nForce4 Ultra
Funzioni di controllo dell’ambiente:
ITE 8712F / 8716F
Fornisce le funzionalità legacy Super Monitoraggio hardware
Super I/O
I/O usate più comunemente.
Controller velocità ventolina
Interfaccia LPC (Low Pin Count)
Funzione "Smart Guardian" di ITE
Alloggi DIMM DDR2 x 4
Memoria
principale
IDE
Modulo di memoria DDR2 a canale doppio
Ciascun DIMM supporta DDR2
Supporto di DDR2 400 / 533 / 667 / 800
256/512MB e 1GB
DIMM registrati e DIMM Non-ECC non sono
Capacità massima della memoria 4GB supportati
Modalità Bus Master Ultra DMA 33 / 66 / 100 /
133
Supporto modalità PIO Mode 0-4
Controller IDE integrato
Controller Serial ATA integrato
SATA
Velocità di trasferimento dei dati fino Compatibile specifiche SATA Versione 2.0.
a 3.0 Gb/s.
LAN
Realtek 8201CL
Codec
audio
ALC 655 / 658(optional)
AC’97 Versione 2.3
Output S/PDIF
x4
Alloggio PCI Express x16
x1
Alloggio PCI Express x1
x2
Connettori Connettore floppy
su scheda Connettore Porta stampante
x1
Ciascun connettore supporta 2 unità Floppy
x1
Ciascun connettore supporta 1 Porta stampante
Connettore IDE
x2
Ciascun connettore supporta 2 unità IDE
Connettore SATA
x4
Ciascun connettore supporta 1 unità SATA
Connettore pannello frontale
x1
Supporta i servizi del pannello frontale
Connettore audio frontale
x1
Supporta la funzione audio pannello frontale
Connettore CD-in
x1
Supporta la funzione input audio CD
Connettore output SPDIF
x1
Supporta la funzione d’output audio digitale
x1
Alimentazione ventolina CPU (con funzione Smart
Fan)
Collettore ventolina sistema
x3
Alimentazione ventolina di sistema
Collettore apertura telaio
(optional)
x1
Collettore ventolina CPU
50
Capacità Half / Full Duplex
Uscita audio 6 canali
Alloggio PCI
Alloggi
Negoziazione automatica 10 / 100 Mb/s
Per la funzione di rilevamento intrusione telaio
TForce4 U AM2
SPECIFICA
Collettore cancellazione CMOS x1
Connettore USB
x3
Connettore alimentazione
(24 pin)
x1
Connettore alimentazione
(4 pin)
x1
Tastiera PS/2
x1
Mouse PS/2
I/O
Porta seriale
pannello
posteriore Porta LAN
Porta USB
Connettore audio
Dimension
i scheda
Ciascun connettore supporta 2 porte USB
pannello frontale
x1
x1
x1
x4
x3
218 mm (larghezza) x 293 mm
(altezza)
Caratterist nTunes NVIDIA
iche
Supporto RAID 0 / 1 / 0+1 / 5
speciali
Sistemi
operativi
supportati
Biostar si riserva il diritto di aggiungere o
Windows 2K / XP
rimuovere il supporto di qualsiasi sistema
operativo senza preavviso.
51
Motherboard Manual
SPANISH
Especificación
Conector AM2
CPU
La arquitectura AMD 64 permite el procesado de 32 y
Procesadores AMD Athlon 64 / Athlon 64 64 bits
FX / Athlon 64X2 / Sempron
FSB
Conjunto de
chips
Soporta las tecnologías Hyper Transport y Cool’n’Quiet
Admite HyperTransport con un ancho de
banda de hasta 1000 MHz
nVIDIA nForce4 Ultra
Iniciativas de control de entorno,
ITE 8712F / 8716F
Súper E/S
Le ofrece las funcionalidades heredadas de Monitor hardware
uso más común Súper E/S.
Controlador de velocidad de ventilador
Interfaz de cuenta Low Pin
Función "Guardia inteligente" de ITE
Ranuras DIMM DDR2 x 4
Módulo de memoria DDR2 de canal Doble
Memoria
Cada DIMM admite DDR de 256/512MB y Admite DDR2 de 400 / 533 / 667 / 800
principal
1GB
No admite DIMM registrados o DIMM no compatibles
Capacidad máxima de memoria de 4GB
con ECC
IDE
SATA
Red Local
Códecs de
sonido
Soporte los Modos PIO 0~4,
Controlador ATA Serie Integrado
Tasas de transferencia de hasta 3.0 Gb/s.
Compatible con la versión SATA 2.0.
Negociación de 10 / 100 Mb/s
Realtek 8201CL PHY
Funciones Half / Full dúplex
Salida de sonido de 6 canales
ALC 655 / 658 (opcional)
AC’97 Versión 2.3
Salida S/PDIF
Ranura PCI
Ranuras
Modo bus maestro Ultra DMA 33 / 66 / 100 / 133
Controlador IDE integrado
X4
Ranura PCI Express x16
X1
Ranura PCI express x 1
X2
Conectores Conector disco flexible
X1
Cada conector soporta 2 unidades de disco flexible
en placa
Conector Puerto de impresora
X1
Cada conector soporta 1 Puerto de impresora
Conector IDE
X2
Cada conector soporta 2 dispositivos IDE
Conector SATA
X4
Cada conector soporta 1 dispositivos SATA
52
Conector de panel frontal
X1
Soporta instalaciones en el panel frontal
Conector de sonido frontal
X1
Soporta funciones de sonido en el panel frontal
Conector de entrada de CD
X1
Soporta función de entrada de sonido de CD
Conector de salida S/PDIF
X1
Soporta función de salida de sonido digital
TForce4 U AM2
Especificación
Cabecera de ventilador de CPU
X1
Fuente de alimentación de ventilador de CPU (con
función Smart Fan)
Cabecera de ventilador de sistema X3
Fuente de alimentación de ventilador de sistema
Cabecera de chasis abierto(opcional)X1
Función de detección de intrusos en el chasis
Cabecera de borrado de CMOS
X1
Conector USB
X3
Conector de alimentación
X1
Cada conector soporta 2 puertos USB frontales
(24 patillas)
Conector de alimentación
X1
(4 patillas)
Panel
trasero de
E/S
Tamaño de
la placa
Teclado PS/2
X1
Ratón PS/2
X1
Puerto serie
X1
Puerto de red local
X1
Puerto USB
X4
Conector de sonido
X3
218 mm. (A) X 293 Mm. (H)
Funciones
NVIDIA nTunes
especiales
Admite RAID 0 / 1 / 0+1 / 5
Soporte de
sistema
operativo
Windows 2K / XP
Biostar se reserva el derecho de añadir o retirar el
soporte de cualquier SO con o sin aviso previo.
53
Motherboard Manual
PORTUGUESE
ESPECIFICAÇÕES
A arquitectura AMD 64 permite uma computação de 32
Socket AM2
CPU
e 64 bits
Processadores AMD Athlon 64 / Athlon 64
FX / Althlon 64X2 / Sempron
FSB
Chipset
Suporta a tecnologia HyperTransport com
uma largura de banda até 1000 MHz
nVIDIA nForce4 Ultra
ITE 8712F / 8716F
Especificaçã
o Super I/O
Suporta as tecnologias Hyper Transport e Cool’n’Quiet
Iniciativas para controlo do ambiente
Proporciona as funcionalidades mais
utilizadas em termos da especificação
Super I/O.
Monitorização do hardware
Controlador da velocidade da ventoinha
Função "Smart Guardian" da ITE
Interface LPC (Low Pin Count).
Ranhuras DIMM DDR2 x 4
Módulo de memória DDR2 de canal duplo
Memória
Cada módulo DIMM suporta uma
Suporta módulos DDR2 400 / 533 / 667 / 800
principal
memória DDR2 de 256/512 MB & 1 GB
Os módulos DIMM registados e os DIMM Non-ECC não
Capacidade máxima de memória: 4 GB
são suportados
Controlador IDE integrado
Modo Bus master Ultra DMA 33 / 66 / 100 / 133
IDE
Suporta o modo PIO 0~4,
Controlador Serial ATA integrado
SATA
Velocidades de transmissão de dados até Compatibilidade com a especificação SATA versão 2.0.
3.0 Gb/s.
LAN
Codec de
som
Ranhuras
Saída de áudio de 6 canais
AC’97 Versão 2.3
Saída S/PDIF
Ranhura PCI
x4
Ranhura PCI Express x16
x1
Ranhura PCI Express x 1
54
Capacidade semi/full-duplex
ALC 655 / 658 (opcional)
Conectores Conector da unidade de disquetes
na placa
Auto negociação de 10 / 100 Mb/s.
Realtek 8201CL PHY
x2
x1
Cada conector suporta 2 unidades de disquetes
Conector da para impressora
x1
Cada conector suporta 1 Porta para impressora
Conector IDE
x2
Cada conector suporta 2 dispositivos IDE
Conector SATA
x4
Cada conector suporta 1 dispositivo SATA
Conector do painel frontal
x1
Para suporte de várias funções no painel frontal
Conector de áudio frontal
x1
Suporta a função de áudio no painel frontal
Conector para entrada de CDs
x1
Suporta a entrada de áudio a partir de CDs
TForce4 U AM2
ESPECIFICAÇÕES
Conector de saída S/PDIF
x1
Conector da ventoinha da CPU
x1
Conector da ventoinha do sistema
x3
Conector para detecção da
abertura do chassis
x1
Conector para limpeza do CMOS
x1
Conector USB
x3
Conector de alimentação
x1
Suporta a saída de áudio digital
Alimentação da ventoinha da CPU (com a função Smart
Fan)
Alimentação da ventoinha do sistema
Para detectar qualquer intrusão no chassis
Cada conector suporta 2 portas USB no painel frontal
(24 pinos)
Conector de alimentação
x1
(4 pinos)
Teclado PS/2
x1
Rato PS/2
x1
aídas no
Porta série
x1
painel
Porta LAN
x1
Porta USB
x4
Tomada de áudio
x3
Entradas/S
traseiro
Tamanho
da placa
Característi
cas
especiais
218 mm (L) X 293 mm (A)
nTunes da NVIDIA
Suporta as funções RAID 0 / 1 / 0+1 / 5
A Biostar reserva-se o direito de adicionar ou remover
Sistemas
operativos
suportados
Windows 2K / XP
suporte para qualquer sistema operativo com ou sem
aviso prévio.
55
Motherboard Manual
POLISH
SPEC
Architektura AMD 64 umożliwia przetwarzanie 32 i 64
Socket AM2
Procesor
AMD Athlon 64 / Athlon 64 FX / Procesory bitowe
Althlon 64X2 / Sempron
FSB
Chipset
Obsługa Hyper Transport oraz Cool’n’Quiet
Obsługa HyperTransport o szerokości
pasma do 1000 MHz
nVIDIA nForce4 Ultra
Gniazda DDR2 DIMM x 4
Pamięć
Każde gniazdo DIMM obsługuje moduły
główna
256/512MB oraz 1GB DDR2
Obsługa DDR2 400 / 533 / 667 / 800
Brak obsługi Registered DIMM oraz Non-ECC DIMM
Maks. wielkość pamięci 4GB
Funkcje kontroli warunków pracy,
ITE 8712F / 8716F
Super I/O
Moduł pamięci DDR2 z trybem podwójnego kanału
Zapewnia najbardziej powszechne funkcje Monitor H/W
Super I/O.
Kontroler prędkości wentylatora
Interfejs Low Pin Count
Funkcja ITE "Smart Guardian"
Zintegrowany kontroler IDE
IDE
Ultra DMA 33 / 66 / 100 / 133 Tryb Bus
obsługa PIO tryb 0~4,
Master
SATA
LAN
Kodek
dźwiękowy
Zintegrowany kontroler Serial ATA
Złącza
Działanie w trybie połowicznego / pełnego dupleksu
8 kanałowe wyjście audio
ALC 655 / 658 (opcja)
AC’97 w wersji 2.3
Wyjście S/PDIF
x4
Gniazdo PCI Express x16
x1
Gniazdo PCI Express x 1
x2
Złącze napędu dyskietek
x1
Każde złącze obsługuje 2 napędy dyskietek
x1
Każde złącze obsługuje 1 Port drukarki
wbudowane Złącze Port drukarki
56
10 / 100 Mb/s oraz automatyczną negocjacją szybkości
Realtek 8201CL PHY
Gniazdo PCI
Gniazda
Zgodność ze specyfikacją SATA w wersji 2.0.
Transfer danych do 3.0 Gb/s.
Złącze IDE
x2
Każde złącze obsługuje 2 urządzenia IDE
Złącze SATA
x4
Każde złącze obsługuje 1 urządzenie SATA
Złącze panela przedniego
x1
Obsługa elementów panela przedniego
Przednie złącze audio
x1
Obsługa funkcji audio na panelu przednim
Złącze wejścia CD
x1
Obsługa funkcji wejścia audio CD
Złącze wyjścia S/PDIF
x1
Obsługa funkcji cyfrowego wyjścia audio
TForce4 U AM2
SPEC
Złącze główkowe wentylatora procesora ... Zasilanie wentylatora procesora (z funkcją Smart Fan)
Złącze główkowe wentylatora
systemowego
x3
Złącze główkowe otwarcia
obudowy (opcja)
x1
Zasilanie wentylatora systemowego
Do funkcji wykrywania naruszenia obudowy
Złącze główkowe kasowania
CMOS
x1
Złącze USB
x3
Złącze zasilania (24 pinowe)
x1
Złącze zasilania (4 pinowe)
x1
Klawiatura PS/2
x1
Mysz PS/2
x1
Back Panel Port szeregowy
x1
I/O
x1
Wymiary
płyty
Port LAN
Port USB
x4
Gniazdo audio
x3
218mm (S) X 293 mm (W)
Funkcje
NVIDIA nTunes.
specjalne
Obsługa RAID 0 / 1 / 0+1 / 5
Obsluga
systemu
operacyjne
go
Każde złącze obsługuje 2 porty USB na panelu
przednim
Biostar zastrzega sobie prawo dodawania lub
Windows 2K / XP
odwoływania obsługi dowolnego systemu
operacyjnego bez powiadomienia.
57
Motherboard Manual
RUSSIAN
СПЕЦ.
CPU
(центральн
ый
процессор)
FSB
Набор
микросхем
Гнездо AM2
Архитектура AMD 64 разрешать обработка данных
Процессоры AMD Athlon 64 / Athlon 64
на 32 и 64 бит
FX / Althlon 64X2 / Sempron
Поддержка Hyper Transport и Cool’n’Quiet
Поддержка HyperTransport с
пропускной способностью до 1000 МГц
nVIDIA nForce4 Ultra
Слоты DDR2 DIMM x 4
Модуль памяти с двухканальным режимом DDR2
Основная
Каждый модуль DIMM поддерживает
Поддержка DDR2 400 / 533 / 667 / 800
память
256/512МБ & 1ГБ DDR2
Не поддерживает зарегистрированные модули
Максимальная ёмкость памяти 4 ГБ
DIMM and Non-ECC DIMM
ITE 8712F / 8716F
Инициативы по охране окружающей среды,
Обеспечивает наиболее используемые
Super I/O
действующие функциональные
Регулятор скорости
возможности Super I/O.
Функция ITE "Smart Guardian" (Интеллектуальная
Интерфейс с низким количеством
защита)
выводов
IDE
SATA
Локальная
сеть
Звуковой
кодек
Слоты
Встроенны
й разъём
Встроенное устройство управления
Режим "хозяина" шины Ultra DMA 33 / 66 / 100 / 133
встроенными интерфейсами устройств Поддержка режима PIO 0~4,
Встроенное последовательное
скорость передачи данных до 3.0 гигабит/с.
устройство управления ATA
Соответствие спецификации SATA версия 2.0.
Автоматическое согласование 10 / 100 Мб/с .
Realtek 8201CL PHY
Частичная / полная дуплексная способность
Шестиканальный звуковой выход
ALC655 / 658 (дополнительно)
AC’97 Версия 2.3Вывод S/PDIF
Слот PCI
x2
Слот PCI Express x16
x1
Слот PCI Express x 1
x1
Разъём НГМД
x1
Разъём Порт подключения принтера....
Разъём IDE
58
Аппаратный монитор
x2
Каждый разъём поддерживает 2 накопителя на
гибких магнитных дисках
Каждый разъём поддерживает 1 Порт подключения
принтера
Каждый разъём поддерживает 2 встроенных
интерфейса накопителей
Разъём SATA
x4
Каждый разъём поддерживает 1 устройство SATA
Разъём на лицевой панели
x1
Поддержка устройств на лицевой панели
TForce4 U AM2
СПЕЦ.
Входной звуковой разъём
x1
Поддержка звуковых функций на лицевой панели
Разъём ввода для CD
x1
Поддержка функции ввода для CD
Разъём вывода для S/PDIF
x1
Поддержка вывода цифровой звуковой функции
Источник питания для вентилятора центрального
Контактирующее приспособление
вентилятора центрального процессора..
Контактирующее приспособление
вентилятора системы
x3
Шасси открытого контактирующего
приспособления (дополнительно) x1
процессора (с функцией интеллектуального
вентилятора)
Источник питания для вентилятора системы
Для функции обнаружения злоумышленника шасси
Открытое контактирующее
Задняя
приспособление CMOS
x1
USB-разъём
x3
Разъем питания (24 вывод)
x1
Разъем питания (4 вывод)
x1
Клавиатура PS/2
x1
Мышь PS/2
x1
панель
Последовательный порт
x1
средств
Порт LAN
x1
USB-порт
x4
ввода-выв
ода
панели
лицевой панели
Гнездо для подключения
наушников
Размер
Каждый разъём поддерживает 2 USB-порта на
x3
218 мм (Ш) X 293 мм (В)
Специальн
ые
технически NVIDIA nTunes
е
Поддержка RAID 0 / 1 / 0+1 / 5
характерис
тики
Поддержка
OS
Biostar сохраняет за собой право добавлять или
Windows 2K / XP
удалять средства обеспечения для OS с или без
предварительного уведомления.
59
‫‪Motherboard Manual‬‬
‫‪ARABIC‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬
‫وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ‬
‫اﻟﻤﺮآﺰﻳﺔ‬
‫اﻟﻨﺎﻗﻞ اﻷﻣﺎﻣﻲ اﻟﺠﺎﻧﺒﻲ‬
‫ﻣﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ‬
‫‪AM2‬ﻣﻘﺒﺲ‬
‫‪AMD Athlon 64 / Athlon 64 FX /‬ﻣﻌﺎﻟﺠﺎت‬
‫‪Althlon 64X2 / Sempron‬‬
‫ﺗﺮدد‬
‫‪nVIDIA nForce4 Ultra‬‬
‫ﻋﺪد‪4‬‬
‫ﺳﻌﺔ ‪ DDR2‬ﺗﺪﻋﻢ ذاآﺮة ﻣﻦ ﻧﻮع ‪DIMM‬ﺗﺪﻋﻢ آﻞ ﻓﺘﺤﺔ‬
‫ﻣﻴﺠﺎ ﺑﺎﻳﺖ و‪ 1‬ﺟﻴﺠﺎ ﺑﺎﻳﺖ‪256/512‬‬
‫ﻣﺰدوﺟﺔ اﻟﻘﻨﺎة‪DDR2‬وﺣﺪة ذاآﺮة‬
‫ﻣﻴﺠﺎ ﺑﺎﻳﺖ‪ 400 / 533 / 667 / 800‬ﺳﻌﺎت ‪DDR2‬ﺗﺪﻋﻢ اﻟﺬاآﺮة ﻣﻦ ﻧﻮع‬
‫‪ ECC‬اﻟﻤﺴﺠﻠﺔ وﺗﻠﻚ اﻟﺘﻲ ﻻ ﺗﺘﻮاﻓﻖ ﻣﻊ ‪DIMM‬ﻻ ﺗﺪﻋﻢ رﻗﺎﺋﻖ اﻟﺬاآﺮة‬
‫ﺳﻌﺔ ذاآﺮة ﻗﺼﻮى ‪ 4‬ﺟﻴﺠﺎ ﺑﺎﻳﺖ‬
‫‪Super I/O‬‬
‫‪ Cool’n’Quiet‬و ‪Hyper Transport‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫‪ 1000‬ﺑﺘﺮدد ﻳﺼﻞ إﻟﻰ ‪HyperTransport‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫ﻓﺘﺤﺔ ‪DDR2 DIMM‬‬
‫اﻟﺬاآﺮة اﻟﺮﺋﻴﺴﻴﺔ‬
‫إﺟﺮاء اﻟﻌﻤﻠﻴﺎت اﻟﺤﺎﺳﻮﺑﻴﺔ ﺑﺴﺮﻋﺔ ‪ 32‬و‪ 64‬ﺑﺖ‪AMD 64‬ﺗﻤﻜﻦ ﺗﻘﻨﻴﺔ‬
‫‪ITE 8712F / 8716F‬‬
‫وﺳﺎﺋﻞ اﻟﺘﺤﻜﻢ ﻓﻲ اﻟﺒﻴﺌﺔ‪:‬‬
‫اﻷآﺜﺮ اﺳﺘﺨﺪاﻣًﺎ‪Super I/O .‬ﺗﻮﻓﺮ وﻇﻴﻔﺔ‬
‫ﻣﺮاﻗﺐ ﻟﻤﻌﺮﻓﺔ ﺣﺎﻟﺔ اﻷﺟﻬﺰة‬
‫‪Low Pin Count Interface‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫ﻣﺮاﻗﺐ ﻓﻲ ﺳﺮﻋﺔ اﻟﻤﺮوﺣﺔ‬
‫‪ ITE‬ﻣﻦ "‪"Smart Guardian‬وﻇﻴﻔﺔ‬
‫ﻣﺘﻜﺎﻣﻞ‪IDE‬ﻣﺘﺤﻜﻢ‬
‫ﻣﻨﻔﺬ ‪IDE‬‬
‫‪Ultra DMA 33 / 66 / 100 / 133‬ﻧﺎﻗﻞ ﺑﺘﻘﻨﻴﺔ‬
‫‪PIO Mode 0~4‬دﻋﻢ وﺿﻊ‬
‫وﺿﻊ رﺋﻴﺴﻲ‬
‫‪ASAT‬‬
‫ﻣﺘﻜﺎﻣﻞ‪Serial ATA‬ﻣﺘﺤﻜﻢ‬
‫‪ 2.0.‬اﻹﺻﺪار ‪SATA‬ﻣﻄﺎﺑﻘﺔ ﻟﻤﻮاﺻﻔﺎت‬
‫ﻧﻘﻞ اﻟﺒﻴﺎﻧﺎت ﺑﺴﺮﻋﺎت ﺗﺼﻞ إﻟﻰ ‪ 3.0‬ﺟﻴﺠﺎﺑﺖ‪/‬ﺛﺎﻧﻴﺔ‪.‬‬
‫ﺷﺒﻜﺔ داﺧﻠﻴﺔ‬
‫‪Realtek 8201CL PHY‬‬
‫آﻮدﻳﻚ اﻟﺼﻮت‬
‫)اﺧﺘﻴﺎري(‪ALC 655 / 658‬‬
‫ﺗﻔﺎوض ﺗﻠﻘﺎﺋﻲ ‪ 100/10‬ﻣﻴﺠﺎ ﺑﺎﻳﺖ ‪ /‬ﺛﺎﻧﻴﺔ و‬
‫إﻣﻜﺎﻧﻴﺔ اﻟﻨﻘﻞ اﻟﻤﺰدوج اﻟﻜﺎﻣﻞ‪/‬اﻟﻨﺼﻔﻲ‬
‫ﻗﻨﻮات ﻟﺨﺮج اﻟﺼﻮت‪6‬‬
‫‪ AC’97‬ﻣﻦ ‪2.3‬اﻹﺻﺪار‬
‫‪S/PDIF‬ﺧﺮج‬
‫اﻟﻔﺘﺤﺎت‬
‫ﻓﺘﺤﺔ ‪PCI‬‬
‫ﻋﺪد ‪4‬‬
‫ﻓﺘﺤﺔ ‪PCI Express x16‬‬
‫ﻋﺪد ‪1‬‬
‫ﻓﺘﺤﺔ ‪PCI Express x 1‬‬
‫ﻋﺪد ‪2‬‬
‫اﻟﻤﻨﺎﻓﺬ ﻋﻠﻰ ﺳﻄﺢ‬
‫ﻣﻨﻔﺬ ﻣﺤﺮك أﻗﺮاص ﻣﺮﻧﺔ‬
‫ﻋﺪد ‪1‬‬
‫اﻟﻠﻮﺣﺔ‬
‫ﻣﻨﻔﺬ ﻃﺎﺑﻌﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ‪IDE‬‬
‫ﻋﺪد ‪2‬‬
‫‪IDE‬ﻳﺪﻋﻢ آﻞ ﻣﻨﻔﺬ اﺛﻨﻴﻦ ﻣﻦ أﺟﻬﺰة‬
‫ﻣﻨﻔﺬ ‪SATA‬‬
‫ﻋﺪد ‪4‬‬
‫‪SATA‬ﻳﺪﻋﻢ آﻞ ﻣﻨﻔﺬ واﺣﺪ ﻣﻦ أﺟﻬﺰة‬
‫ﻣﻨﻔﺬ اﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻳﺪﻋﻢ ﺗﺠﻬﻴﺰات اﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‬
‫ﻣﻨﻔﺬ اﻟﺼﻮت اﻷﻣﺎﻣﻲ‬
‫ﻋﺪد ‪1‬‬
‫ﻳﺪﻋﻢ وﻇﻴﻔﺔ اﻟﺼﻮت ﺑﺎﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‬
‫ﻳﺪﻋﻢ ﻣﺤﺮآﻴﻦ ﻟﻸﻗﺮاص اﻟﻤﺮﻧﺔ‬
‫ﻣﻨﻔﺬ ‪CD-IN‬‬
‫ﻋﺪد ‪1‬‬
‫ﻳﺪﻋﻢ وﻇﻴﻔﺔ دﺧﻞ ﺻﻮت اﻟﻘﺮص اﻟﻤﺪﻣﺞ‬
‫ﻣﻨﻔﺬ ﺧﺮج ‪S/PDIF‬‬
‫ﻋﺪد ‪1‬‬
‫ﻳﺪﻋﻢ وﻇﻴﻔﺔ ﺧﺮج اﻟﺼﻮت اﻟﺮﻗﻤﻲ‬
‫وﺻﻠﺔ ﻣﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰﻳﺔ‬
‫ﻋﺪد ‪1‬‬
‫(‪Smart Fan‬ﻟﺘﻮﺻﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ )ﻣﻊ وﻇﻴﻔﺔ‬
‫وﺻﻠﺔ ﻣﺮوﺣﺔ اﻟﻨﻈﺎم‬
‫ﻋﺪد ‪3‬‬
‫ﻟﺘﻮﺻﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ اﻟﻨﻈﺎم‬
‫وﺻﻠﺔ ﻓﺘﺢ اﻟﻬﻴﻜﻞ)اﺧﺘﻴﺎري(‬
‫ﻋﺪد ‪1‬‬
‫ﻟﻠﻜﺸﻒ ﻋﻦ اﺧﺘﺮاق اﻟﻬﻴﻜﻞ‬
‫وﺻﻠﺔ ﻣﺴﺢ ‪CMOS‬‬
‫ﻋﺪد ‪1‬‬
‫‪60‬‬
‫‪TForce4 U AM2‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬
‫ﻣﻨﻔﺬ ‪USB‬‬
‫ﻋﺪد ‪3‬‬
‫ﻣﻨﻔﺬ ﺗﻮﺻﻴﻞ اﻟﻄﺎﻗﺔ )‪24‬دﺑﻮس(‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ﺗﻮﺻﻴﻞ اﻟﻄﺎﻗﺔ )‪4‬دﺑﺎﺑﻴﺲ(‬
‫ﻋﺪد ‪1‬‬
‫ﻟﻮﺣﺔ ﻣﻔﺎﺗﻴﺢ ‪PS/2‬‬
‫ﻋﺪد ‪1‬‬
‫ﻣﺎوس ‪PS/2‬‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﺎﻓﺬ دﺧﻞ‪/‬ﺧﺮج‬
‫ﻣﻨﻔﺬ ﺗﺴﻠﺴﻠﻲ‬
‫ﻋﺪد ‪1‬‬
‫اﻟﻠﻮﺣﺔ اﻟﺨﻠﻔﻴﺔ‬
‫ﻣﻨﻔﺬ ﺷﺒﻜﺔ اﺗﺼﺎل ﻣﺤﻠﻴﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﺎﻓﺬ ‪USB‬‬
‫ﻋﺪد ‪4‬‬
‫ﻣﻘﺒﺲ ﺻﻮت‬
‫ﻣﺰاﻳﺎ ﺧﺎﺻﺔ‬
‫ﺣﺠﻢ اﻟﻠﻮﺣﺔ‬
‫دﻋﻢ أﻧﻈﻤﺔ اﻟﺘﺸﻐﻴﻞ‬
‫‪61‬‬
‫ﺑﺎﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‪USB‬ﻳﺪﻋﻢ آﻞ ﻣﻨﻔﺬ ﻓﺘﺤﺘﻲ‬
‫ﻋﺪد ‪3‬‬
‫‪NVIDIA nTunes‬‬
‫‪RAID 0 / 1 / 0+1 / 5‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫‪ 218‬ﻣﻢ )ﻋﺮض( ‪ 293 X‬ﻣﻢ )ارﺗﻔﺎع(‬
‫‪Windows 2K / XP‬‬
‫ﺑﺤﻘﻬﺎ ﻓﻲ إﺿﺎﻓﺔ أو إزاﻟﺔ اﻟﺪﻋﻢ ﻷي ﻧﻈﺎم ﺗﺸﻐﻴﻞ ﺑﺈﺧﻄﺎر أو ﺑﺪون إﺧﻄﺎر‪Biostar.‬ﺗﺤﺘﻔﻆ‬
Motherboard Manual
JAPANESE
仕様
AMD 64アーキテクチャでは、32ビットと64ビット計算が可
Socket AM2
CPU
AMD Athlon 64 / Athlon 64 FX / Althlon
64X2 / Sempron プロセッサ
FSB
能です
ハイパートランスポートとクールアンドクワイアットをサポ
ートします
1000 MHz のバンド幅までハイパートランス
ポートをサポートします
チップセット nVIDIA nForce4 Ultra
DDR2 DIMMスロット x 4
メインメモリ
各DIMMは 256/512MB & 1GB DDR2をサポ
ート
DDR2 400 / 533 / 667 / 800をサポート
登録済みDIMMと非ECC DIMMはサポートされません
最大メモリ容量4GB
ITE 8712F / 8716F
Super I/O
デュアル チャンネルモードDDR2メモリモジュール
環境コントロールイニシアチブ、
もっとも一般に使用されるレガシーSuper I/O H/Wモニター
機能を採用しています。
ファン速度コントローラ/ モニター
低ピンカウントインターフェイス
ITEの「スマートガーディアン」機能
統合IDEコントローラ
IDE
Ultra DMA 33 / 66 / 100 / 133バスマスタモ PIO Mode 0~4のサポート、
ード
SATA
LAN
統合シリアルATAコントローラ
SATAバージョン2.0仕様に準拠。
最高 3.0 Gb/秒のデータ転送速度
10 / 100 Mb/秒のオートネゴシエーション
Realtek 8201CL PHY
半/全二重機能
6チャンネルオーディオアウト
サウンド
Codec
スロット
ALC 655 / 658 (オプション)
AC’97バージョン2.3
S/PDIF アウト
PCIスロット
x4
PCI Express x16スロット
x1
PCI Express x 1スロット
x2
オンボードコ フロッピーコネクタ
x1
各コネクタは2つのフロッピードライブをサポートします
ネクタ
プリンタポートコネクタ
x1
各コネクタは1つのプリンタポートをサポートします
IDEコネクタ
x2
各コネクタは2つのIDEデバイスをサポートします
SATAコネクタ
x4
各コネクタは1つのSATAデバイスをサポートします
フロントパネルコネクタ
x1
フロントパネル機能をサポートします
フロントオーディオコネクタ
x1
フロントパネルオーディオ機能をサポートします
CDインコネクタ
x1
CDオーディオイン機能をサポートします
62
TForce4 U AM2
仕様
S/PDIFアウトコネクタ
x1
CPUファンヘッダ
x1
CPUファン電源装置(スマートファン機能を搭載)
システムファンヘッダ
x3
システムファン電源装置
シャーシオープンヘッダ(オプション)
x1
シャーシ侵入検出機能
CMOSクリアヘッダ
x1
USBコネクタ
x3
電源コネクタ(24ピン)
x1
電源コネクタ(4ピン)
x1
PS/2キーボード
x1
PS/2マウス
x1
背面パネル
シリアルポート
x1
I/O
LANポート
x1
USBポート
x4
オーディオジャック
x3
デジタルオーディオアウト機能をサポートします
各コネクタは2つのフロントパネルUSBポートをサポートし
ます
ボードサイズ 218 mm (幅) X 293 mm (高さ)
特殊機能
NVIDIA nTunes
RAID 0 / 1 / 0+1 / 5 のサポート
OSサポート Windows 2K / XP
Biostarは事前のサポートなしにOSサポートを追加または削
除する権利を留保します。
63