PW191 Series
LCD Monitor
User Guide
E2744
First Edition V1
August 2006
Copyright © 2006 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form
or by any means, except documentation kept by the purchaser for backup purposes, without the
express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or
altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the
serial number of the product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS
OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR
ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND
SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY
OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered
trademarks or copyrights of their respective companies, and are used only for identification or
explanation and to the owners’ benefit, without intent to infringe.
ii
Table of contents
Notices ................................................................................................ iv
Safety information ............................................................................... v
Care & Cleaning ................................................................................... vi
Package contents ............................................................................. viii
Chapter 1:
Product introduction
1.1
Welcome! .............................................................................. 1-2
1.2
Features ............................................................................... 1-2
1.3
Monitor introduction ............................................................. 1-3
Chapter 2:
Setup
2.1
2.2
Unfolding the monitor .......................................................... 2-2
Connecting the cables .......................................................... 2-2
2.3
Turning on the monitor ........................................................ 2-3
2.4
Adjusting the tilt .................................................................. 2-4
2.5
Detaching the stand (for VESA wall mount) ........................ 2-5
Chapter 3:
3.1
General Instruction
OSD (On-Screen Display) menu ............................................ 3-2
3.1.1
How to reconfigure ................................................. 3-2
3.1.2
OSD Function Introduction ..................................... 3-2
®
3.2
Pivot Pro Software .............................................................. 3-5
3.3
Troubleshooting (FAQ) ......................................................... 3-6
3.4
Specification summary ......................................................... 3-7
3.5
Supported operating modes ............................................... 3-13
iii
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with
manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
A s a n E n e r g y S t a r® P a r t n e r , o u r c o m p a n y h a s d e t e r m i n e d t h a t
t h i s p r o d u c t m e e t s t h e E n e r g y S t a r® g u i d e l i n e s f o r e n e r g y
efficiency.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian
ICES-003.
iv
Safety information
• Before setting up the monitor, carefully read all the documentation that
came with the package.
• To prevent fire or shock hazard, never expose the monitor to rain or
moisture.
• Never try to open the monitor cabinet. The dangerous high voltages
inside the monitor may result in serious physical injury.
• If the power supply is broken, do not try to fix it by yourself. Contact a
qualified service technician or your retailer.
• Before using the product, make sure all cables are correctly connected
and the power cables are not damaged. If you detect any damage,
contact your dealer immediately.
• Slots and openings on the back or top of the cabinet are provided for
ventilation. Do not block these slots. Never place this product near or
over a radiator or heat source unless proper ventilation is provided.
• The monitor should be operated only from the type of power source
indicated on the label. If you are not sure of the type of power supply to
your home, consult your dealer or local power company.
• Use the appropriate power plug which complies with your local power
standard.
• Do not overload power strips and extention cords. Overloading can result
in fire or electric shock.
• Avoid dust, humidity, and temperature extremes. Do not place the
monitor in any area where it may become wet. Place the monitor on a
stable surface.
• Unplug the unit during a lightning storm or if it will not be used for a long
period of time. This will protect the monitor from damage due to power
surges.
• Never push objects or spill liquid of any kind into the slots on the monitor
cabinet.
• To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate configured receptacles marked
between 100-240V AC.
• If you encounter technical problems with the monitor, contact a qualified
service technician or your retailer.
v
Care & Cleaning
• Before you lift or reposition your monitor, it is better to disconnect the
cables and power cord. Follow the correct lifting techniques when
positioning the monitor. When lifting or carrying the monitor, grasp the
edges of the monitor. Do not lift the display by the stand or the cord.
• Cleaning. Turn your monitor off and unplug the power cord. Clean the
monitor surface with a lint-free, non-abrasive cloth. Stubborn stains may
be removed with a cloth dampened with mild cleaner.
• Avoid using a cleaner containing alcohol or acetone. Use a cleaner
intended for use with the LCD. Never spray cleaner directly on the
screen, as it may drip inside the monitor and cause an electric shock.
The following symptoms are normal with the monitor:
• The screen may flicker during the initial use due to the nature of the
fluorescent light. Turn off the Power Switch and turn it on again to make
sure that the flicker disappears.
• You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
• When the same image is displayed for hours, an afterimage of the
previous screen may remain after switching the image. The screen will
recover slowly or you can turn off the Power Switch for hours.
• When the screen becomes black or flashes, or cannot work anymore,
contact your dealer or service center to fix it. Do not repair the screen
by yourself!
Conventions used in this guide
W A R N I N G : Information to prevent injury to yourself when trying to
complete a task.
C A U T I O N : Information to prevent damage to the components
when trying to complete a task.
I M P O R T A N T : Information that you MUST follow to complete a
task.
N O T E : Tips and additional information to aid in completing a task.
vi
Where to find more information
Refer to the following sources for additional information and for product
and software updates.
1.
ASUS websites
The ASUS websites worldwide provide updated information on ASUS
hardware and software products. Refer to http://www.asus.com
2.
Optional documentation
Your product package may include optional documentation, such as
warranty card, that may have been added by your dealer. These
documents are not part of the standard package.
vii
Package contents
Check your PW191 Series LCD package for the following items:
LCD monitor
Quick Start Guide
Support CD
1 x Power cord
1 x Power adapter
1 x VGA cable
1 x DVI cable (PW191/PW191A)
1 x Audio cable
1 x Rear connector cover
If any of the above items is damaged or missing, contact your retailer
immediately.
viii
This chapter gives a g
general description of
the ASUS LCD monitor PW191 Series. The
chapter lists the monitor features including
introduction on the front and rear panels.
Product introduction
Chapter 1
1.1
Welcome!
Thank you for purchasing the ASUS® PW191 Series LCD monitor!
The latest widescreen LCD monitor from ASUS provides a crisper, broader,
and brighter display, plus a host of features that enhance your viewing
experience. You can turn the ASUS® PW191 Series LCD monitor
counterclockwise for portrait orientation, giving you a full view of
documents and web pages, and saving you the trouble of having to scroll
the bar while you read or surf the Internet. The PW191 Series also features
a rotating swivels, adjustable tilt and height, and an anti-reflection glare
type panel (PW191 only) that protects your eyes and makes your monitor
easy to clean. Smart sensor buttons on the front panel are shown in weak
LED lights until you touch them, elegance and stylish functionality of the
PW191 Series.
With these features, you enjoy the convenience and delightful visual
experience that the PW191 Series brings you!
1.2
1-2
Features
•
19" Widescreen LCD Monitor
•
Recommended resolution: 1440 X 900
•
Anti-reflection glare type panel (PW191 only)
•
8ms (Tr+Tf) Quick response time (PW191)
5ms (Tr+Tf) Quick response time (PW191A/PW191S)
•
SPLENDID™ Video Enhancement Technology
•
5 Video preset modes switiched by hotkey
•
3 Skin-tones selection
•
Flexible display orientation including portrait/landscape
•
Tilt/height adjustment
•
Swivel/90º rotation
•
Microsoft Windows® 2000/XP compliance
•
VESA Display Data Channel DDC2B compliance
•
VESA wall mount compliance (100x100mm)
•
EPA ENERGY STAR® and ergonomic design
•
Touch sensor buttons
•
Both VGA and DVI-D Inputs (PW191/PW191A)
•
2W x 2 Stereo speakers and earphone output
•
RoHS compliance
Chapter 1: Product introduction
1.3
Monitor introduction
Front of the LCD monitor
Stereo
Speaker
Base
3
1
22
3
44
55
The touch sensors are sensitive. Slight touch the function you want to
enable. Do not press the front panel too hard to prevent damage to the
panel and the sensors.
•
Sensor:
Touch this sensor to enter/select the icon (function) highlighted
while the OSD menu is activated.
•
Sensor:
Touch this sensor to decrease the value of the function selected
or move to the previous fuction.
This is also a hotkey for Volume adjustment.
1.
2.
•
3.
•
•
Sensor:
Touch this sensor to increase the value of the function selected
or move to the next function.
This is also a hotkey for Brightness adjustment.
ASUS LCD Monitor PW191 Series
1-3
4.
Sensor:
• Use this hotkey to switch from five video preset modes (Game
Mode, Night View Mode, Scenery Mode, Standard Mode, Theater
Mode) with SPLENDID™ Video Enhancement Technology.
• Exit the OSD menu or go back to the previous menu as the OSD
menu is active.
• Automatically adjust the image to its optimized position, clock,
and phase by touching the sensor for 2-4 seconds.
5.
Power sensor/indicator
• Touch this sensor to turn the monitor on/off
Status
Blue
1-4
Description
ON
Amber
Standby mode
OFF
OFF
Chapter 1: Product introduction
Rear of the LCD monitor
1
2
3
4
5
1.
D C - i n p o r t . This port connects the power connector from the
bundled power adapter.
2.
D V I p o r t . This 24-pin port is for PC (Personal Computer) DVI-D
digital signal connection. (PW191/PW191A)
V G A p o r t . This 15-pin port is for PC VGA connection.
3.
4.
Audio-in port
. This port connects PC audio source by the
bundled audio cable .
5.
Headphone port
mini-plug (3.5mm).
. This port connects a headphone with a stereo
The headphone is purchased separately.
ASUS LCD Monitor PW191 Series
1-5
1-6
Chapter 1: Product introduction
Chapter 2
Setup
This chapter provides instructions on how to
correctly connect cables and properly adjust
the tilt of the LCD monitor.
2.1
Unfolding the monitor
The monitor is folded in the package. To unfold the monitor, hold
the stand with one hand and carefully tilt the monitor forward
with the other hand.
Stand
2.2
Connecting the cables
To connect the cables:
1.
Adjust the monitor
to your desired
height and tilt.
2.
Turn the monitor
90º counterclockwise
so you can clearly see
the ports at the
bottom of the rear
panel.
Input ports
Front view
2-2
Side view
Chapter 2: Setup
3.
Connect the cables as shown:
Power adapter
VGA cable
Audio cable
• To connect the audio cable: connect one end of the audio cable to
the monitor’s Audio-in port, and then connect the other end to the
computer multi-media (or audio) card’s audio output.
• To connect the power adapter: first, connect the adapter cord
securely to the monitor’s DC-in port. Then, connect the power plug to
the adapter port with the other end to a power outlet.
• To connect the VGA cable:
a. Plug the VGA/DVI connector to the LCD monitor’s VGA/DVI port.
b. Connect the other end of the VGA/DVI cable to your computer’s
VGA/DVI port.
c. Tighten the two screws to secure the VGA/DVI connector.
4.
Close the rear connector cover.
Align the cover to the three slots
near the ports and close the cover
carefully. A click indicates that the
cover has been closed successfully.
2.3
Turning the monitor on
Gently touch the power sensor . See page 1-4 for the location of the
power sensor. The power indicator lights up in blue to show that the
monitor is ON.
ASUS LCD Monitor PW191 Series
2-3
2.4
Adjusting the monitor
You can adjust the monitor to several directions as shown below.
• For optimal viewing, we recommend that you look at the full face of the
monitor, then adjust the monitor to the angle that is most comfortable
for you.
• Hold the stand to prevent the monitor from falling when you change its
angle.
• You can adjust the monitor’s angle from -5º to 25º.
-5º~25º
• You can also turn the monitor 90º counterclockwise.
90º
2-4
Chapter 2: Setup
• The stand allows you to turn the monitor left/right up to 120º.
120º
2.5
Detaching the stand
(for VESA wall mount)
The detachable stand of the PW191 monitor is specially designed for VESA
wall mount.
To detach the stand:
1.
Turn the VESA cover counterclockwise to open it.
2.
Remove the VESA cover from the stand.
Have the front of the monitor face down to make the detachment safer
and easier. We recommend that you cover the surface with soft cloth to
prevent damage to the monitor.
ASUS LCD Monitor PW191 Series
2-5
3.
Use a screwdriver to remove the four screws on the stand of the
monitor.
The VESA wall mount (100 mm x 100 mm) is purchased separately.
2-6
Chapter 2: Setup
This chapter introduces the operating
instruction, including how to use the
OSD (On-Screen Display) menu and the
Pivot®Pro software.
General Instruction
Chapter 3
3.1
OSD (On-Screen Display) menu
3.1.1
How to reconfigure
1.
Touch the
sensor to activate
the OSD menu.
2.
Touch
and
to navigate through the functions. Highlight and
activate the desired function by touching the
sensor. If the
function selected has a sub-menu, touch
and
again to
navigate through the sub-menu functions. Highlight and activate the
desired sub-menu function by touching the
sensor.
3.
Touch
4.
To exit the OSD menu, touch the
to adjust any other function.
3.1.2
to change the settings of the selected function.
sensor. Repeat step 2 and step 3
OSD Function Introduction
Spendid
This function contains five
sub-functions you can select
for your preference.
1.
•
•
•
•
•
3-2
and
Scenery Mode: advance for scenery use with SPLENDID™ Video
Enhancement.
Standard Mode: advance for general Window use with
SPLENDID™ Video Enhancement.
Theater Mode: advance for movie use with SPLENDID™ Video
Enhancement.
Game Mode: advance for game use with SPLENDID™ Video
Enhancement.
Mode: advance for dark-display use with SPLENDID™
Night View Mode
Video Enhancement.
Chapter 3: General Instruction
Image
You can adjust brightness, contrast,
sharpness, saturation,position (VGA
only), and focus (VGA only) from
this main function.
2.
•
•
•
•
•
•
Brightness: the adjusting range is from 0 to 100.
hotkey to activate this function.
Contrast: the adjusting range is from 0 to 100.
is a
Sharpness: the adjusting range is from 0 to 100.
Saturation: the adjusting range is from 0 to 100.
Position: adjusts the horizontal postition (H-Position) and the
vertical position (V-Position) of the image. The adjusting range is
from 0 to 100.
F o c u s : reduces Horizonal-line noise and Vertical-line noise of the
image by adjusting (Phase) and (Clock) separately. The adjusting
range is from 0 to 100.
•
Phase adjusts the phase of the pixel clock signal. With a wrong
phase adjustment, the screen shows horizontal disturbances.
•
Clock (pixel frequency) controls the number of pixels scanned by
one horizontal sweep. If the frequency is not correct, the screen
shows vertical stripes and the image is not proportional.
Color
Select the image color you like
3.
from this function.
•
•
Color Temp.: contains five color modes including Cool, Normal,
Warm, sRGB, and User mode.
Skin Tone: contains three color modes including Reddish, Natural,
and Yellowish.
In the User mode, colors of R (Red), G (Green), and B (Bluee) are userconfigurable; the adjusting range is from 0-100.
ASUS LCD Monitor PW191 Series
3-3
nput Select
In
In this function, you can select
4.
either VGA or DVI input source.
(PW191/PW191A)
System Setup
Allow you to adjust the system.
5.
•
•
•
•
•
3-4
V o l u m e : the adjusting range is from 0 to 100.
is a hotkey to
activate this function.
OSD Setup: adjusts the horizontal postition (H-Position) and
the vertical position (V-Position) of the OSD. The adjusting range is
from 0 to 100. In the OSD Timeout selection, you can adjust the
OSD timeout from 10 to 120.
Language: there are ten languages for your selection, including
English, German, Italian, French, Dutch, Spanish, Russian, Traditional
Chinese, Simplified Chinese, and Japanese.
Information: shows the monitor information.
R e s e t : Yes allows you to revert to the factory mode. No allows
you to keep the current state.
Chapter 3: General Instruction
3.2
Pivot®Pro Software
• Pivot®Pro is a software that is designed for rotatable monitors. With this
software, you can rotate the image by 90º, 180º, and 270º to meet the
orientation of the monitor.
• Before starting to use this software, install Pivot®Pro into your
PC.
• The Pivot®Pro software is bundled in the support CD.
• Installation instructions:
1. Close all other applications first.
2. Make sure your graphics card manufacturer’s (native)
drivers are installed before you install the Pivot®Pro
software.
3. Insert the support CD into the optical drive and run the
START_PIVOT program.
• This software only supports Windows® 98SE, ME, NT 4.0, 2000, and XP
operating systems.
• After the installation, you can set up hotkeys for different rotation
degrees by pressing the right mouse button -->enter Properties -->
Settings --> Advanced -->Pivot Software -->Hotkeys.
• The default hotkeys for each degree are as follows:
Rotate - Ctrl + Shift + R
0º - Ctrl + Shift + 0
90º - Ctrl + Shift + 9
180º - Ctrl + Shift + 8
270º - Ctrl + Shift + 7
• For more information or help, please go to www.portrait.com.
ASUS LCD Monitor PW191 Series
3-5
3.3
Troubleshooting (FAQ)
Problem
3-6
Possible Solution
Power LED is not ON
• Touch the sensor to check if the monitor is in the ON
mode.
• Check if the power cord is properly connected to the
monitor and the power outlet.
The Power LED lights
amber and there is
no screen image
• Check if the monitor and the computer are in the ON mode.
• Make sure the signal cable is properly connected the
monitor and the computer.
• Inspect the signal cable and make sure none of the pins are
bent.
• Connect the computer with another available monitor to
check if the computer is properly working.
Screen image is too
light or dark
• Adjust the Contrast and Brightness settings via OSD.
Screen image is not
centered or sized
properly
• Touch the sensor for two seconds to automatically
adjust the image.
• Adjust the H-Position or V-Position settings via OSD.
Screen image
bounces or a wave
pattern is present in
the image
• Make sure the signal cable is properly connected to the
monitor and the computer.
• Move electrical devices that may cause electrical
interference.
Screen image has
color defects (white
does not look white)
• Inspect the signal cable and make sure that none of the
pins are bent.
• Perform Reset via OSD.
• Adjust the R/G/B color settings or select the Color
Temperature via OSD.
Screen image is
blurry or fuzzy
• Touch the sensor for two seconds to automatically
adjust the image.
• Adjust the Phase and Clock settings via OSD.
No sound or sound is
low
• Ensure that the audio cable is properly connected to the
monitor and the computer
• Adjust the volume settings of both your monitor and
computer.
• Ensure that the computer sound card driver is properly
installed and activated.
Pivot® is not working
• Ensure that the Pivot®Pro software is installed in your PC.
• Make sure that your PC operating system complies to
Windows® 98SE, ME, NT 4.0, 2000, and XP.
Chapter 3: General Instruction
3.4
Specification summary (PW191)
Panel Type
TFT LCD (Anti-Reflection Glare Panel)
Panel size
19” Wide Screen
Max. Resolution
WXGA + 1440 x 900
Piixel pitch
0.285mm
Brightness (Typ.)
300cd/m2
Contrast Ratio (Typ.)
500:1
Viewing angle(H/V)
150º/130º
Display colors
16.2M
Response time
8ms (Tr+Tf)
ZBD (Zero Bright Dot)
Yes
SPLENDID™ Video
Enhancement
Yes
Splendid selection
5 Video Preset Modes (by
Auto adjustment
Yes (by
Color temperature
selection
Cool/Normal/Warm/sRGB/User Mode
Skin-Tone selection
3 Skin-Tones
DVI port
24-Pin DVI-D
VGA port
15-Pin D-Sub
Audio-in port
3.5mm Mini-jack
Headphone port
3.5mm Mini-jack
Colors
Silver + Black
Speaker (Built-in)
2W x 2 Stereo
Power LED
Blue (ON)/ Amber (Stand-By)
Tilt
+90º ~ -5º
Swivel
+60º ~ -60º
hotkey)
hotkey)
(continued on the next page)
ASUS LCD Monitor PW191 Series
3-7
Specification summary (PW191)
Pivot
0º / 90º (Counterclockwise)
Height adjustment
Yes
VESA wall mount
100 x 100mm
Kensington lock
Yes
Power source
AC: 100~240V 50Hz/60Hz
Power consumption
Power On: < 48W, Standby: < 2W,
Power Off: < 1W
Net weight
8.5 Kg (approx.)
Dimension
520 mm (W) x 490mm (H) x 285mm (D)
Multi-languages
English, German, Italian, French, Dutch, Spanish,
Russian, Traditional Chinese, Simplified Chinese,
Japanese
Accessories
VGA cable, DVI cable, Audio Cable, Power
adapter, Power Cord, Support CD (bundle Pivot®
Pro), Quick Start Guide, Warranty Card (optional)
Regulation approvals
Energy Star®, UL/cUL, CB, CE, FCC, CCC, BSMI,
Gost-R, C-Tick, VCCI, RoHS, MIC
* Specifications are subject to change without notice.
3-8
Chapter 3: General Instruction
Specification summary (PW191A)
Panel Type
TFT LCD (Non-Glare Panel)
Panel size
19” Wide Screen
Max. Resolution
WXGA + 1440 x 900
Piixel pitch
0.285mm
Brightness (Typ.)
300cd/m2
Contrast Ratio (Typ.)
700:1
Viewing angle(H/V)
160º/160º
Display colors
16.2M
Response time
5ms (Tr+Tf)
ZBD (Zero Bright Dot)
Yes
SPLENDID™ Video
Enhancement
Yes
Splendid selection
5 Video Preset Modes (by
Auto adjustment
Yes (by
Color temperature
selection
Cool/Normal/Warm/sRGB/User Mode
Skin-Tone selection
3 Skin-Tones
DVI port
24-Pin DVI-D
VGA port
15-Pin D-Sub
Audio-in port
3.5mm Mini-jack
Headphone port
3.5mm Mini-jack
Colors
Silver + Black
Speaker (Built-in)
2W x 2 Stereo
Power LED
Blue (ON)/ Amber (Stand-By)
Tilt
+90º ~ -5º
Swivel
+60º ~ -60º
hotkey)
hotkey)
(continued on the next page)
ASUS LCD Monitor PW191 Series
3-9
Specification summary (PW191A)
Pivot
0º / 90º (Counterclockwise)
Height adjustment
Yes
VESA wall mount
100 x 100mm
Kensington lock
Yes
Power source
AC: 100~240V 50Hz/60Hz
Power consumption
Power On: < 48W, Standby: < 2W,
Power Off: < 1W
Net weight
8.5 Kg (approx.)
Dimension
520 mm (W) x 490mm (H) x 285mm (D)
Multi-languages
English, German, Italian, French, Dutch, Spanish,
Russian, Traditional Chinese, Simplified Chinese,
Japanese
Accessories
VGA cable, DVI cable, Audio Cable, Power
adapter, Power Cord, Support CD (bundle Pivot®
Pro), Quick Start Guide, Warranty Card (optional)
Regulation approvals
Energy Star®, UL/cUL, CB, CE, FCC, CCC, BSMI,
Gost-R, C-Tick, VCCI, RoHS
* Specifications are subject to change without notice.
3-10
Chapter 3: General Instruction
Specification summary (PW191S)
Panel Type
TFT LCD (Non-Glare Panel)
Panel size
19” Wide Screen
Max. Resolution
WXGA + 1440 x 900
Piixel pitch
0.285mm
Brightness (Typ.)
300cd/m2
Contrast Ratio (Typ.)
700:1
Viewing angle(H/V)
160º/160º
Display colors
16.2M
Response time
5ms (Tr+Tf)
ZBD (Zero Bright Dot)
Yes
SPLENDID™ Video
Enhancement
Yes
Splendid selection
5 Video Preset Modes (by
Auto adjustment
Yes (by
Color temperature
selection
Cool/Normal/Warm/sRGB/User Mode
Skin-Tone selection
3 Skin-Tones
VGA port
15-Pin D-Sub
Audio-in port
3.5mm Mini-jack
Headphone port
3.5mm Mini-jack
Colors
Silver + Black
Speaker (Built-in)
2W x 2 Stereo
Power LED
Blue (ON)/ Amber (Stand-By)
Tilt
+90º ~ -5º
Swivel
+60º ~ -60º
hotkey)
hotkey)
(continued on the next page)
ASUS LCD Monitor PW191 Series
3-11
Specification summary (PW191S)
Pivot
0º / 90º (Counterclockwise)
Height adjustment
Yes
VESA wall mount
100 x 100mm
Kensington lock
Yes
Power source
AC: 100~240V 50Hz/60Hz
Power consumption
Power On: < 48W, Standby: < 2W,
Power Off: < 1W
Net weight
8.5 Kg (approx.)
Dimension
520 mm (W) x 490mm (H) x 285mm (D)
Multi-languages
English, German, Italian, French, Dutch, Spanish,
Russian, Traditional Chinese, Simplified Chinese,
Japanese
Accessories
VGA cable, Audio Cable, Power adapter, Power
Cord, Support CD (bundle Pivot® Pro), Quick
Start Guide, Warranty Card (optional)
Regulation approvals
Energy Star®, UL/cUL, CB, CE, FCC, CCC, BSMI,
Gost-R, C-Tick, VCCI, RoHS
* Specifications are subject to change without notice.
3-12
Chapter 3: General Instruction
3.5
Supported operating modes
Standard
Resolution
Horizontal
Frequency
Vertical
Frequency
Pixel
Frequency
DOS
720 x 400
31.47KHz
70Hz
28.32MHz
VGA
640 x 480
31.47KHz
60Hz
25.18MHz
640 x 480
37.90KHz
72Hz
31.50MHz
640 x 480
37.50KHz
75Hz
31.50MHz
800 x 600
35.16KHz
56Hz
36.00MHz
800 x 600
37.90KHz
60Hz
40.00MHz
800 x 600
48.10KHz
72Hz
50.00MHz
800 x 600
46.90KHz
75Hz
49.50MHz
1024 x 768
48.40KHz
60Hz
65.00MHz
1024 x 768
56.50KHz
70Hz
75.00MHz
1024 x 768
60.02KHz
75Hz
78.75MHz
1280 x 1024
64.00KHz
60Hz
108.00MHz
SVGA
XGA
SXGA
1280 x 1024
80.00KHz
75Hz
135.00MHz
VESA
1152 x 864
67.50KHz
75Hz
108.00MHz
VESA
(Primary)
1440 x 900
55.94KHz
60Hz
106.00MHz
* Modes not listed in the table may not be supported. For optimal
resolution, we recommend that you choose a mode listed in the table
above.
ASUS LCD Monitor PW191 Series
3-13
3-14
Chapter 3: General Instruction