Meage
Cyan
Bl
Y
ack
llownta
Page : 1
1
Sugar & Salt Ltd.
Meage
Cyan
Bl
Y
ack
llownta
Page : 2
2
Sugar & SatLtd.
z72xx_ifu_inside.qxp
2006.02.20.
17:08
Page 2
Thank you for choosing an Electrolux Cyclone Power vacuum cleaner. These operating instructions cover all Cyclone
Power models. This means that with your specific model,
some accessories may not be included.
Accessories and safety precautions
Before starting
Getting the best results
Removing the contents of the dust container
Cleaning the cartridge filter
Cleaning the motor filters and the micro exhaust filter
Cleaning the hose and nozzle
Troubleshooting and customer information
Electrical supply instructions
WARNING instructions
Guarantee
3
4
4
5
5
6
7
8
9
10
11
2
z72xx_ifu_inside.qxp
2006.02.20.
17:08
Page 3
ACCESSORIES AND SAFETY PRECAUTIONS
Accessories
1. Cartridge filter
2. Plastic extension tube (Z7211)
3. Metal extension tubes (Z7292)
4. Hose
5. Hose handle with suction control
6. Dual purpose floor nozzle
7. Upholstery nozzle
8. Crevice nozzle (Z7292)
1
2
3
Safety precautions
The Cyclone Power should only be used by adults for normal vacuuming in a domestic environment. The vacuum
cleaner features double insulation and does not need to be
earthed.
5
4
6
7
Never vacuum:
• In wet areas
• Close to flammable gas, etc.
• Without filters (this may damage the cleaner). A safety
device is fitted which prevents the dust container closing
without a cartridge filter in place. Do not attempt to force
the dust container shut.
8
Never vacuum:
• Sharp objects
• Fluids (this can cause serious damage to the machine)
• Hot or cold cinders, lit cigarette butts, etc.
• Fine dust from plaster, concrete, flour or ash, for example.
The above can cause serious damage to the motor - damage which is not covered by the warranty.
Electrical cable precautions:
• A damaged cable must be replaced by an authorised
Electrolux service engineer. Damage to the cleaner cable
will not be covered by the warranty.
• Never pull or lift the vacuum cleaner by the cable.
• Disconnect the plug from the mains before cleaning or
maintenance of the vacuum cleaner.
• Regularly check that the cable is not damaged. Never use
the vacuum cleaner if the cable is damaged.
All service and repairs must be carried out by an authorised
Electrolux service engineer. Always keep the vacuum cleaner
in a dry place.
3
z72xx_ifu_inside.qxp
2006.02.20.
17:08
Page 4
BEFORE STARTING
1. Always operate the cleaner with the dust container
installed.
2. Always operate the cleaner with the filter set property
installed.
1
2
4
3
5
6
3. Insert the hose until the catch clicks to engage (press the
catch to engage hose).
4. Attach the plastic tubes (Z7211) or metal tubes (Z7292) to
the hose handle and the floor nozzle.
5. Pull out the cable and plug it in.
6. Press the foot pedal to rewind the cable (take hold of the
plug to prevent it striking you).
7. Press the On/Off button to start the vacuum cleaner.
Adjust the suction power by using the linear suction control or the suction control on the hose handle.
GETTING THE BEST RESULTS
Hard floors: Use the dual purpose floor nozzle with the left
pedal in position (8.)
Carpets: Use the dual purpose floor nozzle with the
left pedal in position (9.)
Reduce suction power for rugs and fabrics.
Upholstered furniture: Use the upholstery nozzle.
7
Skirting boards, crevices, corners, etc.: Use the crevice
nozzle.
For the perfect care of your carpets: use the turbo nozzle.
The rotary motion of its brush gently loosens short-pile carpets where the dirt has been trodden in. It removes stubborn
fluff and pet hairs.
8
9
4
z72xx_ifu_inside.qxp
2006.02.20.
17:08
Page 5
REMOVING THE CONTENTS OF THE DUST CONTAINER
Never operate the cleaner without the dust container installed.
The dust container must be emptied if the window of the dust
container indicator is red when the cleaner is operating at maximum power and the nozzle is raised from the floor.
Never open the top cover with the hose connected to the cleaner.
1
2
3
1. Open the top cover.
2. Remove the dust container from the cleaner.
3. Remove the filter set from the dust container by taking it
in the way indicated
4. Remove the contents of the dust container.
3. Put the filter set back into the dust container.
2. Put the dust container back into the cleaner.
1. Close the top cover.
Note: Empty the dust container even if it is not full (the filters may be
blocked). Also replace after using carpet-cleaning powder.
4
5
6
CLEANING THE FILTERS
Filters should be cleaned regularly and replaced twice a year.
Disconnect from electrical outlet before cleaning filters.
Your cleaner is fitted with a dust container indicator. Before
commencing cleaning, without the hose attached, check the
dust container indicator.
If red, clean or replace filter, if not, attach the hose, extension
tubes and accessories as normal and continue cleaning.
NB: It is normal for the indicator to be red during cleaning.
Cleaning the cartridge filter
7
Always operate the cleaner with the cartridge filter installed.
1. Open the top cover.
2. Remove the dust container from the cleaner.
3. Remove the filter set from the dust container by taking it
as indicated.
5. Remove the cartridge filter by turning it counter-clockwise (A) and pull it out (B) as indicated.
6. Rinse it under tap water.
7. Air dry for approximately 24 hours, to ensure it is completely dry before re-using. Avoid direct sunlight and
extreme drying circumstances (hair-dryer, etc.).
If you wish to use your appliance while the cartridge filter
is drying, you may use the extra cartridge filter inserted in
the packaging box.
5. Insert the cartridge filter into its place (B) and turn it
clockwise (A) as indicated in the icon.
3. Put the filter set back into the dust container.
2. Put the dust container back into the cleaner.
1. Close the top cover.
5
z72xx_ifu_inside.qxp
2006.02.20.
17:08
Page 6
Cleaning the motor filters
2
1
5
4
Motorfilter ‘A’
1. Open the top cover.
2. Remove the dust container from the cleaner.
3. Remove the filter set from the dust container by taking it
as indicated in the icon.
4. Remove the cartridge filter by turning it counter-clockwise (A) and pull it out (B) as indicated in the icon.
5. Remove the filter from its place.
6. Rinse it under tap water and dry it completely.
5. Put the filter back into its place.
4. Insert the cartridge filter into its place (B) and turn it
clockwise (A) as indicated in the icon.
3. Put the filter set back into the dust container.
2. Put the dust container back into the cleaner.
1. Close the top cover.
Motorfilter reference number: EF76
3
Motorfilter ‘B’
1. Open the top cover.
7. Remove the filter from its place.
6. Rinse it under tap water and dry it completely.
7. Put the filter back into its place.
1. Close the top cover.
Motorfilter reference number: EF1
6
Cleaning the micro exhaust filter
7
8
9
8. Open the filter grill to remove the exhaust filter.
9. Take the filter out of the grill.
6. Rinse it under tap water and dry it completely.
9. Put the filter back into the grill.
8. Close the filter grill.
Micro exhaust filter reference number: EF2
Note: Do not use cleaning agents and avoid touching the
delicate filter
surface.
6
z72xx_ifu_inside.qxp
2006.02.20.
17:08
Page 7
CLEANING THE HOSE AND NOZZLE
The vacuum cleaner stops automatically if the nozzle, tube
or hose becomes blocked, or the filters are blocked.
Disconnect from the mains and allow the vacuum cleaner to
cool down for approximately 20-30 minutes. Clear whatever
is causing the blockage and/or replace dirty filters.Then
restart the vacuum cleaner.
1
Tubes and hose
1. Use a cleaning strip or similiar to clear the tubes and
hose.
2. It is sometimes possible to clear the hose by "massaging" it. However, be careful in case the obstruction has
been caused by glass or needles caught inside the hose.
Note: The warranty does not cover any damage to hoses
caused by cleaning them.
Cleaning the floor nozzle
3. To avoid reduction in suction power, frequently clean the
dual purpose floor nozzle. The easiest way to clean it is
by using the hose handle.
2
3
7
z72xx_ifu_inside.qxp
2006.02.20.
17:08
Page 8
TROUBLESHOOTING AND CUSTOMER INFORMATION
Troubleshooting
The vacuum cleaner does not start
1. Check that the cable is connected to the mains.
2. Check that the plug and the cable are not damaged.
3. Check for a blown fuse.
The vacuum cleaner stops
1. Check whether the dust container is full. If so, empty it.
2. Is the nozzle, tube or hose blocked?
3. Are the filters blocked?
Water has entered the vacuum cleaner
It will be necessary to replace the motor by an authorised
Electrolux service engineer.
Damage to the motor caused by the penetration of water is
not covered by the warranty.
Customer Information
Electrolux decline all responsibility for all damages arising
from any improper use of the appliance or in cases of tampering with the appliance. This product is designed with the
environment in mind. All plastic parts are marked for recycling purposes.
For further details see our website: www.electrolux.com
For repairs or accessories, contact the Electrolux Group
Floorcare Helpline on 08706 055 055.
If you have any comments on the cleaner or the
Instructions for Use booklet please contact us on: 08706
055 055
The symbol
on the product or on its packaging indicates
that this product may not be treated as household waste.
Instead it shall be handed over to the applicable collection
point for the recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help
prevent potential negative consequences for the environment
and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed
information about recycling of this product, please contact
your local city office, your household waste disposal service or
the shop where you purchased the product.
8
z72xx_ifu_inside.qxp
2006.02.20.
17:08
Page 9
ELECTRICAL SUPPLY INSTRUCTIONS
Before you start …check
the voltage
Before connecting the
cleaner to an electrical supply ensure that voltage
marked on the data plate
(on the underside of cleaner) is correct for your electrical supply. If is not, do
not use the cleaner but
refer back to your dealer.
Connecting to your electrical supply
Permanently connected to the cleaner is a mains supply (2-core)
cable fitted with a non-rewirable plug incorporating a 13A fuse. In
the event of the fuse requiring replacement the fuse cover should
be removed using a small screwdriver. The old fuse MUST be
replaced by a 13A ASTA approved BS1362 fuse and the fuse cover
must be replaced before the plus is used again. In the event of loss
of the fuse cover, replacements can be obtained from your
Electrolux dealer or Electricity Board and must be of the same
colour as indicated by the coloured insert on the base plug.
If difficulty is experienced in obtaining a replacement, contact your
nearest Electrolux Service Centre. (Please see the separate
Electrolux Service Organisation leaflet).
In no circumstances must the plug be used without a correct
fuse cover fitted.
If the plug that is fitted to your appliance is not suitable for your
socket outlet, it must be cut off and the appropriate plug fitted.
Remove the fuse from the cut off plug. The cut off plug should then
be disposed of to prevent hazard of shocks in case it should be
plugged into a 13 Amp socket in another part of your home
As the colours of the wires in the mains cable of this appliance may
not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured blue must be connected to the terminal
which marked with the letter N or coloured black. The wire which is
coloured brown must be connected to the terminal which is marked
the letter L or coloured red.
If using a three-pin plug, do not make any connection to the terminal marked with the letter E or by the earth symbol or coloured
green or green-and-yellow. This cleaner is double insulated and no
earth-connection is necessary.]
It is in you interest to ensure that the plug is correctly attached to
the mains cable. In case of doubt, have it done by a qualified electrician, as Electrolux cannot regard the repair of faults on the plug
connection as a service that can be given free of charge under the
terms of guarantee.
As a general guide to fitting any plug
• Ensure the lengths of wire inside the plug are prepared correctly.
• Connection should be firmly made after all conductor stands are
entered into the terminal posts.
• When preparing the cable ends take care not to damage the outer
seal, or insulation surrounding the inner conductors.
• Tighten all screws.
• Replace the top cover of the plug and secure.
The wires in the mains cable of this appliance are coloured in
accordance with the following code:
Blue: Neutral.
Brown: Live.
9
z72xx_ifu_inside.qxp
2006.02.20.
17:08
Page 10
When using an electrical appliance, basic precautions should always be followed,
including the following:
READ ALL THE INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER.
WARNING
To reduce the risk of fire, electric shock, or injury:
• Do not use outdoors or on wet surfaces.
• Do not leave vacuum cleaner when plugged in.
• Do not allow to be used as a toy. Close attention is necessary when used near
children. Do not allow children to operate this appliance.
• Use only as described in this manual. Use only manufacturer's recommended attachments.
• Do not use with damaged cord or plug. If vacuum cleaner is not working as it should, has
been dropped, damaged, left outdoors, or dropped into water, return it to a service centre
before using.
• Do not pull or carry by cord, do not use cord as a handle, do not close door on cord.
Keep cord away from heated surfaces.
• Do not use extension cords or outlets with inadequate current carrying capacity.
• Turn off all controls before unplugging.
• Do not unplug by pulling on cord. To unplug, grasp the plug not the cord.
• Do not handle plug or vacuum cleaner with wet hands.
• Do not put any object into openings. Do not use with any opening block, keep free of
dust, lint, hair and anything that may reduce air flow.
• Do not use to pick up anything that is burning or smoking, such as cigarettes, matches or
hot ashes.
• Do not use without dust container in place.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible liquids such as gasoline, or use in areas
where they may be present.
• Store your cleaner indoors in a cool, dry area.
• Keep your work area well lighted.
• Unplug electrical appliances before vacuuming them.
SAVE THESE INSTRUCTIONS
10
z72xx_ifu_inside.qxp
2006.02.20.
17:08
Page 11
GUARANTEE
This guarantee is in addition to your statutory and other legal rights.
Electrolux products are carefully designed, manufactured, tested and inspected and in consequence,
we undertake to replace or repair any part found to be defective in material or workmanship, within
one year of delivery to the original purchaser, free of charge. You may be required to take the product
to your nearest service provider if the product requries attention during the first year.
There are certain conditions which may invalidate this guarantee:
a. It is dependent upon the appliance being correctly installed and used in accordance with the
Company's instructions under normal domestic conditions within the United Kingdom or the
Republic of Ireland.
b. Service at all times must be carried out by an Electrolux Service Representative or authorised agent.
c. The guarantee may be invalidated by unauthorised repair or modification of the appliance.
d. You may be charged by the Electrolux Group if you call for an engineer to resolve a problem that
we believe is covered in the instruction booklet.
The Company does not accept liability for defects arising from neglect, misuse or accident. This guarantee excludes such normal wearing parts as filters, brushes and dust containers as the life of these
depends upon the amount and nature of use.
Proof of the date of purchase will be required before service under guarantee is provided.
For futher assistance call the
Electrolux Group Floorcare Helpline on 08706 055 055.
Important:
For future reference we suggest you record the following details here, and keep the receipt with this
booklet as proof or purchase.
Purchased from: __________________________________________________
Date purchased ____________Model No_____________________________
The Electrolux Group, 101 Oakley
Road, LUTON, BEDFORDSHIRE, LU4 9QQ
Features of the Electrolux vacuum cleaner and accessories with it are protected in Great Britain and abroad by Patents
of Registered Designs.
This appliance conforms with the requirements of the amended E.E.C. directive No. 89/336/EEC relating to electromagnetic compatibility (EMC) CE.
The Electrolux Group may introduce modifications to their product from time to time, and consequently the details given
in this booklet are subject to alteretion without notice.
72xx 02 01 04
11