Denon | 2310CI - AVR AV Receiver | Owner`s manual | Denon 2310CI - AVR AV Receiver Owner`s manual

 Graphical User Interface
English
Use this manual in combination with the
operating guide displayed on the GUI screen.
Menu Map (vpage 21)
Examples of GUI Menu Screen Displays (vpage 22)
Remote Control Unit Operations (vpage 57)
Français
Utilisez ce manuel en même temps que le guide
d’utilisation affiché sur l’écran GUI (Interface
graphique).
AV SURROUND RECEIVER
AVR-2310CI
Owner’s Manual
Manuel de l’Utilisateur
bThe illustrations used for explaining operations in this manual show the buttons of
the main remote control unit.
The same operations can be performed using the buttons with the same names on
the main unit panel.
b Les illustrations des boutons présentes dans ce manuel servent à expliquer le
fonctionnement de la télécommande principale.
Vous pouvez contrôler l’appareil à l’aide du bouton portant le même nom sur la
façade de l’appareil.
Plan du menu (vpage 21)
Exemples d’affichage sur écran et d’affichage avant
(vpage 22)
Fonctionnement de la télécommande (vpage 57)
ENGLISH FRANCAIS
nSAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
HOT SURFACE. DO NOT TOUCH.
The top surface over the internal heat sink may become
hot when operating this product continuously.
PRECAUTION:
SURFACE CHAUDE. NE PAS TOUCHER.
La surface supérieure du dissipateur de chaleur peut
devenir chaude si vous utilisez ce produit en continu.
I
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
IMPOTANT SAFETY
INSTRUCTIONS
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings.
Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
15. Batteries shall not be exposed to excessive heat such as sunshine, fire or
the like.
CAUTION:
•The ventilation should not be impeded by covering the ventilation
openings with items, such as newspapers, tablecloths, curtains,
etc.
•No naked flame sources, such as lighted candles, should be
placed on the unit.
•Observe and follow local regulations regarding battery disposal.
•Do not expose the unit to dripping or splashing fluids.
•Do not place objects filled with liquids, such as vases, on the
unit.
ATTENTION:
•La ventilation ne doit pas être gênée en recouvrant les ouvertures
de la ventilation avec des objets tels que journaux, rideaux, tissus,
etc.
•Aucune flamme nue, par exemple une bougie, ne doit être placée
sur l’appareil.
•Veillez à respecter les lois en vigueur lorsque vous jetez les piles
usagées.
•L’appareil ne doit pas être exposé à l’eau ou à l’humidité.
•Ne pas poser d’objet contenant du liquide, par exemple un vase,
sur l’appareil.
CAUTION:
To completely disconnect this product from the mains, disconnect
the plug from the wall socket outlet.
The mains plug is used to completely interrupt the power supply to
the unit and must be within easy access by the user.
PRECAUTION:
Pour déconnecter complètement ce produit du courant secteur,
débranchez la prise de la prise murale.
La prise secteur est utilisée pour couper complètement
l’alimentation de l’appareil et l’utilisateur doit pouvoir y accéder
facilement.
FRANCAIS ENGLISH
FCC INFORMATION (For US customers)
nNOTE ON USE / OBSERVATIONS RELATIVES A L’UTILISATION
1. PRODUCT
This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
product may not cause harmful interference, and (2) this product must accept any interference received, including
interference that may cause undesired operation.
2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements.
Modification not expressly approved by DENON may void your authority, granted by the FCC, to use the product.
3. NOTE
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This product generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this product does cause harmful interference to radio or
television reception, which can be determined by turning the product OFF and ON, the user is encouraged to try to
correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the product into an outlet on a circuit different from that to which the receiver is connected.
•Consult the local retailer authorized to distribute this type of product or an experienced radio/TV technician for
help.
• Keep the unit free from moisture, water,
and dust.
• Protéger l’appareil contre l’humidité, l’eau
et la poussière.
• Do not let foreign objects into the unit.
• Ne pas laisser des objets étrangers dans
l’appareil.
• Avoid high temperatures.
Allow for sufficient heat dispersion when
installed in a rack.
• Eviter des températures élevées.
Tenir compte d’une dispersion de chaleur
suffisante lors de l’installation sur une
étagère.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
• Do not let insecticides, benzene, and
thinner come in contact with the unit.
• Unplug the power cord when not using the • Ne pas mettre en contact des insecticides,
du benzène et un diluant avec l’appareil.
unit for long periods of time.
• Débrancher le cordon d’alimentation
lorsque l’appareil n’est pas utilisé pendant
de longues périodes.
• Handle the power cord carefully.
Hold the plug when unplugging the cord.
• Manipuler le cordon d’alimentation avec
précaution.
Tenir la prise lors du débranchement du
cordon.
* (For apparatuses with ventilation holes)
• Do not obstruct the ventilation holes.
• Ne pas obstruer les trous d’aération.
• Never disassemble or modify the unit in
any way.
• Ne jamais démonter ou modifier l’appareil
d’une manière ou d’une autre.
II
ENGLISH
n Contents
Getting Started
Flow of operations through playback··········································2
Accessories···················································································2
Cautions on Handling····································································3
Cautions on Installation································································3
About the Remote Control Unit···················································3
Inserting the Batteries···································································3
Operating Range of the Remote Control Unit·······························3
Part Names and Functions····························································4
Front Panel·····················································································4
Display···························································································5
Rear Panel······················································································6
Remote Control Unit······································································7
Connections
Important Information···································································9
Cables Used for Connections························································9
Converting Input video signals for Output (Video Conversion
Function)······················································································ 10
Installing/Setting the Speakers·················································· 11
Connecting the Speakers···························································· 12
Connecting Devices····································································· 13
Connecting Devices not Equipped with HDMI terminals········· 14
Once Connections are Completed··············································20
Turning the Power On··································································20
Turning the Power Off··································································20
Selecting the Input Source··························································20
Settings
Menu Map·····················································································21
Examples of GUI Menu Screen Displays····································22
Making the Optimum Settings for the Connected Speakers
Automatically (Audyssey Auto Setup)·······································23
Making detailed settings (Manual Setup)·································28
Making the Input Settings (Input Setup)···································36
Playback
Playing Components····································································42
Playing Blu-ray Disc / DVD Players···············································42
iPod® Playback············································································42
Listening to FM/AM Broadcasts··················································43
Listening to SIRIUS Satellite Radio Programs·····························44
Operations During Playback·························································46
Selecting the Surround Mode·····················································46
q Playing Sources According to the Sources’ Audio Signal Format/
Number of Channels (Standard Playback)····································46
w Playing in a DENON Original Surround Mode·························47
e Direct Playback········································································47
r Stereo Playback·······································································48
t Playing the Pure Direct Mode·················································48
Adjusting the Sound and Picture Quality (Audio/Video Adjust)
·······································································································48
Adjusting the Sound (Audio Adjust)·············································48
Adjusting the Tone (Tone Control)················································50
Making the MultEQ, Dynamic EQ and Dynamic Volume Settings
(Audyssey Settings)·····································································50
Adjust Tonal Quality for Each Speaker Using Graphic Equalizer
(Manual EQ)·················································································51
Restoring Compressed Audio to Nearly Pre-compressed
Conditions for Playback (RESTORER)··········································52
Adjusting the Audio Delay Time while Watching the Picture (Audio
Delay)···························································································52
Adjusting the Picture Quality (Picture Adjust)······························52
Checking the Status (Information)······························53
Convenient functions
HDMI Control Function································································54
Setting the Power to Standby After a Certain Amount of Time
(Sleep Timer Function)································································54
Adjust the Volume of the Different Speakers···························55
Saving Frequently Used Settings (Quick Select Function)······55
MAIN ZONE settings···································································55
ZONE2 settings···········································································55
Various Memory Functions·························································55
Playing 2-Channel Sound in ZONE2 (Multizone
Function)· ·················································································56
Operating the Connected Devices by Remote
Control Unit
Main Remote Control Unit (RC-1117)·········································57
Registering Preset Codes····························································57
Operating Registered Devices·····················································57
Assigning buttons that are Not Used to Operate Other Devices
(Punch Through Function)·····························································59
Sub Remote Control Unit (RC-1119)··········································60
Other Information································································60
Troubleshooting···································································67
Restoring All the Settings to as They were at the Time of
Purchase (Resetting the Microprocessor)··································70
Specifications·········································································70
List of preset codes···································End of this manual
ENGLISH
Flow of operations through
playback
Perform the operations leading to playback on the AVR-2310CI in
the order shown below.
Connections
Installing/Setting the Speakers (vpage 11)
Thank you for purchasing this DENON product. To ensure proper
operation, please read this owner’s manual carefully before using the
product.
After reading them, be sure to keep them for future reference.
⇩
Connecting the Speakers (vpage 12)
Settings
⇩
Accessories
Check that the following parts are supplied with the product.
Connecting Devices (vpage 13)
Turning the Power On (vpage 20)
Remote Control
Settings
Multi-Zone
⇩
Selecting the Input Source (vpage 20)
qOwner’s manual ...................................................................... 1
wGetting Started ........................................................................ 1
eWarranty (for North America model only) ................................ 1
rService station list ................................................................... 1
tPower cord (Cord length: Approx. 5.6 ft / 1.7 m) .................... 1
y Main remote control unit (RC-1117) ........................................ 1
u R6/AA batteries (for RC-1117) ................................................. 2
i Sub remote control unit (RC-1119) .......................................... 1
o R03/AAA batteries (for RC-1119) ............................................. 2
Q0FM indoor antenna .................................................................. 1
Q1AM loop antenna ..................................................................... 1
Q2Setup microphone
Playback
⇩
(DM-A409, Cord length: Approx. 25 ft / 7.6 m) ....................... 1
Audyssey Auto Setup (vpage 23)
y
i
Q0
Q1
Q2
Information
t
Manual Setup (vpage 28)
b Perform “Manual Setup” as necessary.
Troubleshooting
Input Setup (vpage 36)
Getting Started Connections
Getting Started
Specifications
Playback
Playing Components (vpage 42)
⇩
Selecting the Surround Mode (vpage 46)
⇩
Adjusting the Sound and Picture Quality
(vpage 48)
2
ENGLISH
Getting Started
Cautions on Handling
About the Remote Control Unit
Connections
• Before turning the power switch on
Check once again that all connections are correct and that there are
no problems with the connection cables.
In addition to the AVR-2310CI, the included remote control unit
(RC-1117, 1119) can also be used to operate the equipment listed
below.
• Power is supplied to some of the circuitry even when the unit is
set to the standby mode. When traveling or leaving home for long
periods of time, be sure to unplug the power cord from the power
outlet.
q DENON system components
w Non-DENON system components
Settings
Playback
• About condensation
If there is a major difference in temperature between the inside of
the unit and the surroundings, condensation (dew) may form on
the operating parts inside the unit, causing the unit not to operate
properly.
If this happens, let the unit sit for an hour or two with the power
turned off and wait until there is little difference in temperature
before using the unit.
• By setting the preset memory (vpage 57)
e Sub remote control unit (vpage 60)
Inserting the Batteries
q Lift the clasp and remove the rear cover.
(RC-1117)
(RC-1119)
Multi-Zone
• Cautions on using mobile phones
Using a mobile phone near this unit may result in noise. If so, move
the mobile phone away from this unit when it is in use.
Remote Control
• Moving the unit
Turn off the power and unplug the power cord from the power
outlet.
Next, disconnect the connection cables to other system units before
moving the unit.
• Note that the illustrations in these instructions may differ from the
actual unit for explanation purposes.
NOTE
• Replace the batteries with new ones if the set does not operate even
when the remote control unit is operated close to the unit.
• The supplied batteries are only for verifying operation.
• When inserting the batteries, be sure to do so in the proper direction,
following the “q” and “w” marks in the battery compartment.
• To prevent damage or leakage of battery fluid:
• Do not use a new battery together with an old one.
• Do not use two different types of batteries.
• Do not attempt to charge dry batteries.
• Do not short-circuit, disassemble, heat or dispose of batteries in
flames.
• If the battery fluid should leak, carefully wipe the fluid off the inside
of the battery compartment and insert new batteries.
• Remove the batteries from the remote control unit if it will not be in
use for long periods.
• Used batteries should be disposed of in accordance with the local
regulations regarding battery disposal.
Operating Range of the Remote Control
Unit
Point the remote control unit at the remote sensor when operating it.
w Load the two batteries properly as indicated by the marks in the
battery compartment.
Information
(RC-1117)
R6/AA
(RC-1119)
R03/AAA
Cautions on Installation
(RC-1119)
Troubleshooting
30°
Note:
For proper heat dispersal, do not install this unit in a confined
space, such as a bookcase or similar enclosure.
30°
or
Approx. 23 feet / 7 m
(RC-1117)
b Note
e Put the rear cover back on.
Specifications
b
b
b
Wall
3
NOTE
The set may function improperly or the remote control unit may not
operate if the remote control sensor is exposed to direct sunlight,
strong artificial light from an inverter type fluorescent lamp or infrared
light.
ENGLISH
Getting Started
Part Names and Functions
Front Panel
W6
W5
W4
W3
Button that function in the same way as Main remote control buttons
W2 W1
o
i
For buttons not explained here, see the page indicated in parentheses ( ).
qPower operation button
(ON/STANDBY)··········································· (20)
Q3 Q4
Q5 W9 E0
Front
w
Q6 Q7
e
r t
Q8
y
u
Q9
q q
W0
u u
Buttons, terminals and displays only provided on the main unit
W2HD AUDIO indicator····································· (47)
o,Q0o,Q0
W3MASTER VOLUME indicator
W4Display
W5Remote control sensor·································· (3)
W6TUNING PRESET button····························· (44)
W7SOURCE MODE SELECT button················ (20)
W8FRONT SPEAKERS SELECT button············ (46)
W9DIMMER button··········································· (35)
E0STATUS button············································ (53)
i i
Troubleshooting
indicator······················································· (51)
o,Q0o,Q0
Q1 Q1
Information
Q6Power indicator··········································· (20)
Q7Power switch (hON jOFF)················ (20, 70)
Q8Headphones jack (PHONES)······················· (46)
Q9V. AUX INPUT connectors·························· (17)
W0SETUP MIC jack··········································· (24)
W1AUDYSSEY DYNAMIC VOLUME
Remote Control
q
Rear
Multi-Zone
n Buttons that function in the same way as Front Panel buttons
Playback
Q2
Settings
Q0 Q1 W8
wSURROUND MODE buttons······················· (46)
eMENU button··············································· (21)
rCursor buttons (uio p)·························· (21)
tENTER button·············································· (21)
yRETURN button··········································· (21)
uQUICK SELECT buttons······························ (55)
iMASTER VOLUME control knob················ (42)
oSOURCE SELECT knob······························· (20)
Q0ZONE2 SELECT button···························· (56)
Q1ZONE2 ON/OFF button···························· (56)
Q2RESTORER button······································· (52)
Q3DYNAMIC EQ button··································· (51)
Q4DYNAMIC VOLUME button························ (51)
Q5MULTEQ button·········································· (50)
Connections
W7
Q2 Q2
w w
e e
Q5 Q5
r r
t t
,
o Q0o,Q0
Specifications
Q3 Q3
Q4 Q4
y y
Q0 Q0
ENGLISH
Getting Started
Part Names and Functions
Q7 Tuner reception mode indicators
Display
Q7
Q6
Q4 Q3 Q2Q1
Q5
Q0
o
i u
Connections
Settings
Playback
q
w
Multi-Zone
q Input audio signal indicators
w Input signal channel indicators
Remote Control
These light when digital signals are input.
When playing HD Audio sources, the“
”
indicator lights when an extension channel (a
channel other than the front, center, surround,
surround back or LFE channel) is input. If there
are two or more extension channels, the “
”
and “
” indicators light.
e Information display
Information
The input source name, surround mode, setting
values and other information are displayed
here.
r Output signal channel indicators
t Front speaker indicator
Troubleshooting
These light according to the settings of the
front A and B speakers (vpage 46).
y Monitor output indicators
These light according to the HDMI monitor
output setting.
u QUICK SELECT indicators
Specifications
These light when the Quick Select function is
set (vpage 55).
i Master volume indicator
o MUTE indicator
Lights when the muting mode is set (vpage
46).
e
r t y
Q0 AUDYSSEY indicator
These light as shown below in the different
modes (vpage 50).
: During “MultEQ” operation
:D
uring “MultEQ” , “Dynamic EQ”
operation
: During “MultEQ” , “Dynamic EQ”,
b
When speaker settings are changed after the
“Dynamic Volume” operation
Audyssey Auto Setup procedure, either the
indicators’ frame turns off or all the indicators
turn off.
Q1 SLEEP TIMER indicator
Lights when the sleep timer is operating
(vpage 54).
Q2 RESTORER indicator
Lights during “RESTORER” operation (vpage
52).
Q3 Input mode indicators
Q4 ZONE2 indicator
Lights when signals are being output to the
ZONE2 (vpage 56).
Q5 HDMI indicator
Lights when HDMI input signals are detected
(vpage 14).
Q6 Decoder indicators
The indicator for the currently operating decoder
lights.
This lights according to the reception conditions
when the input source is set to “TUNER”.
•AUTO
This lights when in the auto tuning mode.
•STEREO
In the FM mode, this lights when receiving
analog stereo broadcasts.
•TUNED
This lights when the broadcast is properly
tuned in.
ENGLISH
Rear Panel
Q6
Q5
Q3 Q2 Q1
Q4
Q0
o
i
Connections
Q8 Q7
Getting Started
Part Names and Functions
Settings
Playback
Multi-Zone
Remote Control
Information
e
r
t
iAC OUTLETS··············································· (19)
oAC inlet (AC IN)··········································· (19)
Q0Speaker terminals······································ (12)
Q1FM/AM antenna terminals························ (18)
Q2EXT. IN connectors····································· (17)
Q3COMPONENT VIDEO connectors·············· (15)
Q4HDMI connectors········································ (14)
y
u
Q5RS-232C connector····································· (19)
Q6SIRIUS connector······································· (18)
Q7VIDEO/S-VIDEO connectors······················ (16)
Q8Control Dock for iPod DOCK CONTROL jack
Specifications
qDigital audio connectors···························· (16)
wAnalog audio connectors··························· (15)
eSIGNAL GND terminal······························· (16)
rTRIGGER OUT jacks··································· (19)
tREMOTE CONTROL jacks··························(19)
yPRE OUT connector···································· (12)
uZONE2 connectors·····································(56)
w
Troubleshooting
q
····································································· (15)
ENGLISH
Getting Started
Part Names and Functions
Remote Control Unit
Main Remote Control Unit (RC-1117)
Connections
Front
Rear
q
w
Settings
e
Playback
t
Q6
r
W0
Multi-Zone
t
Remote Control
W1
W2
W3
W4
y
Q1
W5
Q7
Information
Q2
u
Q3
W7
Q8
i
Troubleshooting
o
t
W6
W8
q Remote control signal transmitter
w Indicator······················································ (57)
e Power buttons············································ (20)
r QUICK SELECT buttons····························· (55)
t SOURCE SELECT button··························· (20)
y System buttons·········································· (57)
u MENU button············································· (21)
i Cursor buttons (uio p)························· (21)
o SEARCH button·········································· (43)
Q0 DEVICE SELECT switches···················· (42, 57)
Q1 Master volume control buttons················ (42)
Q2 MUTING button·········································· (46)
Q3 Channel level adjustment button············· (55)
Q4 RETURN button·········································· (21)
Q5 ENTER button············································· (21)
Q6 ZONE2 power button································· (56)
Q7 Tuner operation buttons··························· (44)
Q8 MULTEQ button········································· (50)
Q9 Number buttons (0 ~ 9, +10)······················ (57)
W0 MAIN ZONE power buttons······················ (20)
W1 INPUT MODE button·································· (39)
W2 SLEEP TIMER button·································· (54)
W3 VIDEO SELECT button······························· (38)
W4 RESTORER button······································ (52)
W5 FRONT HEIGHT SPEAKER ON/OFF button
····································································· (50)
W6 Surround mode buttons···························· (46)
W7 DYNAMIC VOLUME button······················· (51)
W8 DYNAMIC EQ button································· (51)
Q4
Q5
Q0
Specifications
Q9
For buttons not explained here, see the page
indicated in parentheses ( ).
NOTE
Buttons on the back panel may operate when the
back lid is pressed.
Operations
control
possible
by
remote
n Operations on the AVR-2310CI
n Operations on six devices other that
the AVR-2310CI
•Preset the remote control codes of the
devices to be operated (vpage 57).
•Switch two device selector switches according
to the devices to be operated.
Position of switches
Operable devices
AVR-2310CI
(MAIN ZONE)
iPod
AVR-2310CI
(ZONE2)
TV
Blu-ray disc player
or
DVD Player
DVD recorder
or
Video deck
Satellite receiver
or
Cable TV
CD player
n ZONE2 operations (vpage 56)
n Punch through setting (vpage 59)
ENGLISH
Sub Remote Control Unit (RC-1119)
w
Connections
q Remote control signal transmitter
w ZONE2 power buttons······························· (56)
e ZONE2 source select buttons···················· (56)
r ZONE2 QUICK SELECT buttons················ (55)
t ZONE2 Tuner operation buttons··············· (60)
y ZONE2 iPod operation buttons················· (60)
u MAIN ZONE source call button················· (60)
i ZONE2 muting button······························· (60)
o ZONE2 volume control buttons·········· (56, 60)
q
Settings
Playback
e
u
t
o
Remote Control
i
Multi-Zone
r
Getting Started
Part Names and Functions
Information
y
Troubleshooting
Specifications
ENGLISH
Getting Started
Connections
n Connection Flow
Connections
Installing/Setting the Speakers (vpage 11)
Settings
Connecting the Speakers (vpage 12)
Important Information
Connections for all compatible audio and video signal formats
are described in this owner’s manual. Please select the types of
connections suited for the equipment you are connecting.
After connections are completed, certain settings must be made on
the receiver. Make the settings indicated“ Set as necessary ”
for the individual items.
NOTE
Playback
Connecting Devices (vpage 13)
Multi-Zone
Connecting Devices not Equipped with HDMI
terminals (vpage 14)
Remote Control
n HDMI (vpage 13)
n Monitor (TV) (vpage 14)
n Playback Components
Information
• Blu-ray Disc player / DVD player (vpage 15)
• iPod® (vpage 15)
• CD Player (vpage 15)
• Record Player (vpage 16)
n Recording Components
Troubleshooting
• Digital Video Recorder (vpage 16)
• Video Cassette Recorder (vpage 16)
n SAT/CABLE Tuner (vpage 17)
n Other Devices
• Video Camera / Game Console (vpage 17)
Specifications
• Component with Multi-channel Output connectors
(vpage 17)
• SIRIUS Connector (vpage 18)
• Antenna terminals (vpage 18)
• External Controller (vpage 19)
n Power Cord
• Do not plug in the power cord until all connections have been
completed.
• When making connections, also refer to the operating instructions
of the other components.
• Be sure to connect the left and right channels properly (left with left,
right with right).
• Do not bundle power cords together with connection cables. Doing
so can result in humming or noise.
Cables Used for Connections
Select the cables according to the equipment being connected.
Audio and video cables
HDMI
connections
HDMI cable
Audio cables
Coaxial digital
connections
Coaxial digital cable
Optical digital
connections
Analog
connections
Optical cable
(White)
L
L
(Red)
R
R
Stereo pin-plug cable
Analog
connections
(monaural, for
subwoofer)
Pin-plug cable
Speaker
connections
Speaker cables
Video cables
Component
video
connections
(Green)
(Blue)
(Red)
Component video cable
S-Video
connections
S-Video cable
Video
connections
(Yellow)
75 Ω/ohms pin-plug video cable
Turning the Power On (vpage 20)
9
ENGLISH
Set as Necessary
Converting Input video signals for Output
(Video Conversion Function)
Connections
Resolutions of HDMI-compatible TVs can be checked at “HDMI Information” (vpage 53).
NOTE
AVR-2310CI
Monitor
Video device
HDMI connector
HDMI connector
HDMI connector
Component video
connectors
Component video
connectors
Component video
connectors
Component video
connectors
S-Video connector
S-Video connector
n Examples of GUI menu
• Menu screen
• Status display screen
When the input source is
switched
When the volume is adjusted
Remote Control
HDMI connector
Input
Multi-Zone
Input
(IN)
MENU
Audio/Video
Adjust
Information
Auto Setup
Manual Setup
Input Setup
S-Video connector
S-Video connector
Video connector
Video connector
Video connector
Video connector
audio
and
video
parameters
Mode
DVD
Auto
Master
Volume
-80.0dB
STEREO
Status display: The operating status is displayed temporarily on the
screen when the input source is switched or the
volume is adjusted.
Specifications
•The video conversion function supports the NTSC, PAL, SECAM, NTSC 4.43, PAL-N, PAL-M and PAL-60
formats.
•The resolution of the video signal input to the AVR-2310CI’s HDMI terminal is the resolution set at
“Resolution” (vpage 38). (1080p HDMI signals and 1080p component signals are output at 1080p,
regardless of the setting.)
Troubleshooting
: When 480i/576i signals are input
various
Information
Input
Adjust
Playback
Output
(MONITOR OUT)
Output
• HDMI signals cannot be converted into analog signals.
• When a non-standard video signal from a game machine or some other source is input, the video
conversion function might not operate.
• 480p/576p/1080i/720p/1080p component video input signals cannot be converted into S-Video or Video
format.
Settings
The AVR-2310CI is equipped with four types of video input/output terminals (HDMI, Component video,
S-Video and video).
Use the terminals according to the devices to be connected.
This function automatically converts various formats of video signals input to the AVR-2310CI into the
format used to output the video signals from the AVR-2310CI to a monitor.
• Set when using the video conversion function.
“Video Convert” (vpage 38)
• Set when changing the resolution of the video signal.
“Resolution” (vpage 38)
Getting Started
Important Information
10
ENGLISH
n When 7.1ch (Surround Back Speaker) Connected
Front speakers
Settings
aDetermine the Speaker Layout
z
2
Playback
Multi-Zone
Remote Control
Center
speaker
z4
z5
Surround speakers
Information
Surround
speaker
Troubleshooting
Surround back speakers
NOTE
It is not possible to use the front height speakers and
surround back speakers simultaneously.
GAs seen from aboveH
3
2
Surround speakers
GAs seen from the sideH
Front height speakers
Front speakers
Center speaker
Subwoofer
Surround
Surround back
speaker
speaker
Front
speaker
2 to 3 feet /
60 to 90 cm Point slightly
downwards
Surround back
speaker
GAs seen from aboveH
2 to 3 feet /
60 to 90 cm
n When 7.1ch (Front Height Speaker) Connected
z1:22 ~ 30˚
z2:90˚
z3:110˚
z
z
Surround
speaker
Surround speakers
Front speakers
Center speaker
Monitor
z1
Specifications
11
Front
speaker
GAs seen from the sideH
n When 6.1ch Connected
Subwoofer
Surround
speaker
z1
Surround
Surround back
speaker
speaker
Front
speaker
2 to 3 feet /
60 to 90 cm Point slightly
downwards
GAs seen from aboveH
Front
speakers
z1:22 ~ 30˚
z2:120˚
Subwoofer
3
Surround back
speakers
Front Height speakers
Subwoofer
z
Front speakers
Center speaker
Monitor
z4:30˚
z5:45˚
z2
z1
Installing All the Speakers
z1:22 ~ 30˚
z2:90˚
z3:110˚
Center speaker
Monitor
Subwoofer
Below we introduce examples of speaker layouts. Refer
to these to arrange your speakers according to their
type and how you want to use them.
n When 5.1ch Connected
GAs seen from the sideH
4
Connections
•The AVR-2310CI is compatible with various types
of surround playback.
• Decide on the surround modes to be played on
the AVR-2310CI before making connections and
settings.
z
Getting Started
Installing/Setting the Speakers
z2
z1
Monitor
z
3
z1:30˚
z2:45˚
z3:90˚
z4:110˚
Point slightly
downwards
Front height
speaker
Front speaker
Surround
speaker
2 to 3 feet /
60 to 90 cm
Surround speakers
GAs seen from aboveH
GAs seen from the sideH
ENGLISH
sSet the “Amp Assign” Mode According to the Speaker Layout
The signals output from the AVR-2310CI’s SURR. BACK/AMP ASSIGN speaker terminals can be
switched to signals of the surround mode being used (vpage 28 “Amp Assign”).
SURR. BACK/AMP ASSIGN
Speaker connections
Subwoofer with
built-in amplifier
Front speakers
A
Center
speaker
Surround
speakers
Example of speaker installation
(L)
(R)
q
w
(L)
q
w
q
*/
Surround back
speakers
(L)
(R)
w
w
q
(R)
q
w
qw
q
Settings
w
Normal
Front speakers
B
Connections
Amp assign mode
(vpage 28)
Connecting the Speakers
Getting Started
Installing/Setting the Speakers
Playback
(7.1)
Multi-Zone
Normal
Surround back
speakers
bConnect to the “L” speaker
terminal.
bSet “S.Back” (vpage 29)
to “1spkr”.
Remote Control
(6.1)
Not connected
Normal
bSet the “S.Back” setting
(vpage 29) to “None”.
Front Height
speakers
Protection circuit
(7.1)
bFor connections, see
“About bi-amp connections”
(vpage 13).
(5.1)
ZONE2
(Default)
MAIN ZONE
ZONE2
ZONE2
speakers
(5.1)
If the core wires touch the rear panel and the screws
etc., or the ± sides touch each other, the protection
circuit will be activated and the power indicator will
flash red at intervals of 0.5 secs.
If the protection circuit is activated, the speaker
output is isolated, and the power supply goes to
the standby state. If the power supply is turned off,
after the power supply cord is withdrawn, please
confirm that speaker cable and input cable are
connected.
Also, if replaying large sound levels by using
a speaker having an impedance less than that
specified (eg, 4 Ω/ohms), the temperature will rise,
and the protection circuit might be activated. The
power supply will go into the standby state, and the
power indicator will flash red at 2 second intervals.
In this case, please switch off the power supply, and
wait until the AVR-2310CI has cooled down, and the
surrounding ventilation is good.
Even if there are no problems with the surrounding
ventilation and connections, in the event of the
protection circuit becoming activated, due to
thinking that the AVR-2310CI has failed, please
contact DENON Service center after switching off.
(2)
12
Specifications
Front A Bi-Amp
or
Front B Bi-Amp
Front A or B
speakers
Troubleshooting
Front Height
For connections of the SURR. BACK/AMP
ASSIGN speaker terminals, see “Amp Assign”
(vpage 28).
Information
(5.1)
ENGLISH
Getting Started
Connecting the Speakers
Carefully check the left (L) and right (R) channels and + (red) and –
(black) polarities on the speakers being connected to the AVR-2310CI,
and be sure to interconnect the channels and polarities correctly.
These connections make for higher quality playback sound with no
interference between the signals of the bass and treble units.
When the amplifier assignment mode is set to “Front A Bi-Amp” or
“Front B Bi-Amp”, connect as shown below. (The illustration shows a
connection example for the front B Bi-Amp speakers.)
2
3
4
Playback
1
Settings
About bi-amp connections
Connections
Connecting the Speaker Cables
Peel off about 10 mm of sheathing from the tip
of the speaker cable, then either twist the core
wire tightly or terminate it.
q
Insert the speaker cable’s core wire to the hilt
into the speaker terminal.
w
(L)
Multi-Zone
Turn the speaker terminal clockwise to tighten
it.
Connecting Devices Equipped with
HDMI terminals
Important Information
n About HDMI
Front speakers B
Turn the speaker terminal counterclockwise
to loosen it.
Connecting Devices
“HDMI” is the abbreviation of “High Definition Multimedia
Interface”. This interface allows transfer of digital video signals
and digital audio signals over a single HDMI cable.
q
w
(R)
AVR-2310CI
Remote Control
n When using a banana plug
“HDMI”, “HDMI logo” and “High-Definition Multimedia Interface”
are trademarks or registered trademarks of HDMI Licensing LLC.
n Functions usable with HDMI connections
Deep Color
Eliminates on-screen color banding, for smooth tonal transitions and
subtle gradations between colors.
x.v.Color
Tighten the speaker terminal firmly before
inserting the banana plug.
Enables displays with natural, vivid colors. “x.v.Color” is a Sony
registered trademark.
Auto Lip Sync (vpage 31)
Information
HDMI 1.3 incorporates an automatic video/audio synching capability
that allows devices to perform this synchronization automatically with
total accuracy.
Use speakers with an impedance of 6 to 16 Ω/ohms. When using front
A and B speakers simultaneously, use speakers with an impedance of
12 to 16 Ω/ohms.
NOTE
Troubleshooting
•Connect the speaker cables in such a way that they do not stick out
of the speaker terminals. The protection circuit may be activated if
the core wires touch the rear panel or if the + and – sides touch each
other (v “Protection circuit”).
•Never touch the speaker terminals while the power
supply is connected. Doing so could result in electric shock.
When in the “Front A Bi-Amp” and “Front B Bi-Amp” modes, the
same signals are output from the front speaker terminals and the AMP
ASSIGN terminals.
NOTE
Specifications
•Use speakers compatible with bi-amp connections.
•When making bi-amp connections, be sure to remove the shortcircuiting plate or wire between the speaker’s woofer and tweeter
terminals.
HDMI control function (vpage 31, 54)
This function allows you to operate external devices from the receiver
and operate the receiver from external devices.
NOTE
•These functions will not work if the device connected to the HDMI
terminal does not support Deep Color or x.v.Color signal transfer or
the Auto Lip Sync function.
•The HDMI control function may not work depending on the device it
is connected to and its settings.
•You cannot operate a TV or Blu-ray Disc player / DVD player that is
not compatible with the HDMI control function.
n Copyright protection system (HDCP)
The AVR-2310CI supports HDCP (High-bandwidth Digital Contents
Protection). HDCP is a copyright protection technology for digital video
signals. The devices connected to the AVR-2310CI must also support
HDCP.
NOTE
13
When a device that does not support HDCP is connected, video
signals are not properly output.
ENGLISH
Connections
The AVR-2310CI allows connection of inputs from up to 5 HDMI
devices and output to 1 TV.
nConnecting to a device equipped with a DVI-D
terminal
NOTE
)%.*
065
)%.*
065
SAT/CABLE
Tuner
)%.*
065
Digital Video
Recorder
)%.*
065
nSettings related to HDMI connections
For instructions on HDMI connections, see “Connecting Devices
Equipped with HDMI terminals” on page 13.
Monitor (TV)
"6%*0
015*$"065
7*%&0
7*%&0
*/
47*%&0
*/
Playback
Blu-ray
Disc Player
•Select the terminal to use and connect the device.
•For video connections, see “Converting input video signals for output
(Video Conversion Function)” (vpage 10).
$0.10/&/57*%&0
*/
:
1# 13
Set as necessary. For details, see the respective reference pages.
Multi-Zone
Input terminal assignment (vpage 37)
Set this when changing the input sources of the different terminals.
)%.*
065
Monitor
(TV)
)%.*
*/
Make these settings related to HDMI input/output signals.
•RGB Range
•Auto Lip Sync
•HDMI Audio Out
•HDMI Control
•Standby Source
•Power Off Control
Information
NOTE
The audio signals output from the HDMI connectors are only the
HDMI input signals.
Troubleshooting
NOTE
•If the menu “HDMI Audio Out” setting (vpage 31) is set to “Amp”,
the sound may be interrupted when the monitor’s power is turned
off.
•The audio signal from the HDMI output terminal (sampling
frequency, number of channels, etc.) may be limited by the HDMI
audio specifications of the connected device regarding permissible
inputs.
The component video connectors may be indicated differently on your
monitor. For details, see the monitor’s operating instructions.
14
Specifications
•Use a cable on which the HDMI logo is indicated (a certified HDMI
product) for connection to the HDMI connector. Normal playback
may not be possible when using a cable other than one on which the
HDMI logo is indicated (a non-HDMI-certified product).
•When the AVR-2310CI is connected to other devices with HDMI
cables, also connect the AVR-2310CI and TV using an HDMI cable.
•When a device supporting Deep Color signal transfer is connected,
use a cable compatible with HDMI ver.1.3a.
•Video signals are not output if the input video signals do not match
the monitor’s resolution. In this case, switch the Blu-ray Disc player /
DVD player’s resolution to a resolution with which the monitor is
compatible.
HDMI Setup (vpage 31)
Remote Control
Game
Console
Settings
DVD
Player
•No sound is output when connected to a device equipped with a
DVI-D terminal. Also make the audio connections.
•Signals cannot be output to DVI-D devices that do not support
HDCP.
•Depending on the combination of devices, the video signals may not
be output.
Monitor (TV)
Connections
When an HDMI/DVI conversion cable (sold separately) is used, the
HDMI video signals are converted to DVI signals, allowing connection
to a device equipped with a DVI-D terminal.
Connecting Devices not
Equipped with HDMI terminals
Getting Started
Connecting devices
ENGLISH
Getting Started
Connecting Devices not Equipped with HDMI terminals
CD Player
Control dock for iPod®
Playback Components
Connections
Use a DENON control dock for iPod (ASD-1R, ASD-11R, ASD-3N or
ASD-3W sold separately) to connect the iPod to the AVR-2310CI. For
instructions on the control dock for iPod settings, refer to the control
dock for iPod’s operating instructions.
Blu-ray Disc player / DVD player
Select the terminal to use and connect the device.
For instructions on HDMI connections, see “Connecting Devices
Equipped with HDMI terminals” on page 13.
Settings
7*%&0
"6%*0
"6%*0
065
3
Control dock for iPod
Blu-ray Disc player /
DVD player
Playback
$0.10/&/57*%&0
065
:
1# 13
CD Player
L
R
L
R
ASD-3N or
ASD-3W
"6%*0
$0"9*"065
"6%*0
065
3
Multi-Zone
L
R
L
R
R
L
R
L
Remote Control
Information
Troubleshooting
Set as necessary
Set this to change the input signal to which the input source
is assigned.
“Input Assign” (vpage 37)
Specifications
Set as necessary
Set as necessary
Set this to change the input signal to which the input source
is assigned.
“Input Assign” (vpage 37)
NOTE
When connected to a Blu-ray Disc player, and playing Dolby TrueHD,
DTS-HD, Dolby Digital Plus, connect the HDMI.
15
Set this to assign the iPod to a terminal other than “VCR
(iPod)”.
“iPod Dock” (vpage 37)
With the default settings, the iPod can be used connected to the VCR
(iPod) connector.
ENGLISH
Record Player
Recording Components
Digital Video Recorder
Video Cassette Recorder
Select the terminal to use and connect the device.
Select the terminal to use and connect the device.
For instructions on HDMI connections, see “Connecting Devices
Equipped with HDMI terminals” on page 13.
For instructions on HDMI connections, see “Connecting
Devices Equipped with HDMI terminals” on page 13.
Video cassette recorder
7*%&0
L
$0.10/&/57*%&0
065
:
1# 13
"6%*0
7*%&0
065
015*$"065
7*%&0
"6%*0
065
3
7*%&0
*/
"6%*0
"6%*0
*/
3
015*$"*/
"6%*0
7*%&0
"6%*0
*/
3
47*%&0
*/
7*%&0
7*%&0
065
47*%&0
065
"6%*0
"6%*0
065
3
Playback
"6%*0
065
(/%
Settings
DVD Recorder
R
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
Multi-Zone
L
Connections
Turntable
(MM cartridge)
Getting Started
Connecting Devices not Equipped with HDMI terminals
Remote Control
Information
Troubleshooting
• The AVR-2310CI is compatible with record players with an MM
cartridge. When you connect to a record player with an MC
cartridge, use a commercially available MC head amp or a step-up
transformer.
• When you increase the volume without connecting the record player,
there may be “booming” noise from the speakers.
Set as necessary
Set this to change the input signal to which the input source is
assigned.
“Input Assign” (vpage 37)
NOTE
•To record video signals through the AVR-2310CI, use the same type of video
cable for connection between the AVR-2310CI and the player as the cable
used for connection between the AVR-2310CI and the recorder.
•Do not connect the output of the component connected to the AVR-2310CI’s
OPTICAL2 output connector to any input connector other than OPTICAL2.
•Digital signals are not output from the analog REC OUT connector.
Set as necessary
Set this to change the input signal to which the input
source is assigned.
“Input Assign” (vpage 37)
NOTE
•To record video signals through the AVR-2310CI, use the same
type of video cable for connection between the AVR-2310CI
and the player as the cable used for connection between the
AVR-2310CI and the recorder.
•Digital signals are not output from the analog REC OUT
connector.
16
Specifications
NOTE
The SIGNAL GND terminal of the AVR-2310CI is not a safety ground
connection. Connect it to reduce noise when noise is excessive.
Note that depending on the record player, connecting the ground line
may have the reverse effect of increasing noise. In this case, it is not
necessary to connect the ground line.
ENGLISH
Getting Started
Connecting Devices not Equipped with HDMI terminals
SAT/CABLE Tuner
Select the terminal to use and connect the device.
Connections
For instructions on HDMI connections, see “Connecting Devices
Equipped with HDMI terminals” on page 13.
SAT/CABLE Tuner
"6%*0
Settings
"6%*0
065
3
Playback
L
Multi-Zone
L
$0"9*"065
Component with Multi-channel Output connectors
Other Devices
Video Camera / Game Console
Blu-ray Disc player / DVD player /
External decoder
Video camera /
Game console
"6%*0
7*%&0
7*%&0
47*%&0
065
7*%&0
065
47*%&0
065
"6%*0
7*%&0
065
The video signal can be connected in the same way as a Blu-ray Disc
player / DVD player (vpage 15).
"6%*0
065
3
L
R
L
R
015*$"065
46#
800'&3
'30/5
-
3
$&/5&3
463306/%
-
3
463306/%
#"$,
-
3
L
R
L
R
L
R
L
R
L
R
L
R
R
R
Remote Control
Information
Troubleshooting
Set as necessary
Set as necessary
Specifications
Set this to change the input signal to which the input source
is assigned.
“Input Assign” (vpage 37)
17
Set as necessary
Set this to change the input signal to which the input source
is assigned.
“Input Assign” (vpage 37)
To play analog signals input from the external input (EXT. IN)
terminal, set “Input Mode” (vpage 39) on the menu to “EXT.
IN”.
“EXT. IN” can also be selected with
.
ENGLISH
SIRIUS Connector
Antenna terminals
•The AVR-2310CI is a SIRIUS Satellite Radio Ready® receiver. You can receive SIRIUS® Satellite Radio by
connecting to the SiriusConnect Home Tuner and subscribing to the SIRIUS service.
•Plug the SIRIUS connector on the rear panel.
•Position the Home Tuner antenna near a south-facing window to receive the best signal.
For details, see “Listening to SIRIUS Satellite Radio Programs” (vpage 44, 45).
When making connections, also refer to the operating instructions of the SiriusConnect Home Tuner.
Direction of broadcasting station
75 Ω/ohms
Coaxial cable
Settings
AM loop
antenna
(supplied)
FM indoor antenna
(supplied)
SIRIUSConnect Home Tuner
Connections
FM antenna
Getting Started
Connecting Devices not Equipped with HDMI terminals
Playback
NOTE
Keep the power cord unplugged until the SiriusConnect Home Tuner connection have been completed.
nPositioning the Antenna
For a consistent satellite signal, the antenna must be positioned correctly. Use the following map to
determine which area you are in and position the antenna accordingly.
NORTH
WEST
q
t
w
r
e
SOUTH
1
1
2
Remove the vinyl tie and take
out the connection line.
Push the lever.
Insert the conductor.
2
3-1
Bend in the reverse direction.
With the antenna
on top of any
stable surface.
Mount
the antenna
3-2With
attached to a wall.
Installation hole Mount on wall, etc.
3
Return the lever.
NOTE
•Do
not
connect
two
FM
antennas
simultaneously.
•Even if an external AM antenna is used, do not
disconnect the AM loop antenna.
•Make sure the AM loop antenna lead terminals do
not touch metal parts of the panel.
18
Specifications
Area 1 :Point the antenna toward the sky in the east,
northeast, or southeast, either through a
window or outside.
Area 2 :Point the antenna toward the sky in the north
or northeast, either through a window or
outside.
Area 3 :Point the antenna toward the sky in the north
or northwest, either through a window or
EAST
outside.
Area 4 :Point the antenna toward the sky in the west,
northwest, or southwest, either through a
HORIZON
window or outside.
Area 5 :Put the antenna outside and point it straight
up. The antenna cannot be used indoors.
SKY
nConnection of AM antennas
Troubleshooting
“SIRIUS, XM and all related marks and logos are trademarks of Sirius XM Radio Inc. and its subsidiaries.
All rights reserved. Service not available in Alaska and Hawaii.”
nAM loop antenna assembly
Information
Set this to change the input signal to which the input source
is assigned.
“Input Assign” (vpage 37)
Ground
Remote Control
Set as necessary
AM outdoor antenna
Multi-Zone
bWhen connecting
digital audio
ENGLISH
Getting Started
Connecting Devices not Equipped with HDMI terminals
External Controller
n RS-232C connector
Connections
When you connect an external control device, you can control
the AVR-2310CI with the external control device. Perform
the operation below beforehand.
Connecting the Power Cord
n REMOTE CONTROL jacks
Infrared
retransmitter
Infrared
sensor
Settings
qTurn on the AVR-2310CI’s power.
wTurn off the AVR-2310CI’s power from the external
controller.
eCheck that the AVR-2310CI is in the standby mode.
"69
065
Input
Output
Wait until all connections have been completed before connecting the
power cord.
Power cord
Extension jack for future use.
(Connect devices corresponding
with room to room function to
this jack.)
To household
power outlet
(AC 120 V, 60 Hz)
Playback
Connection to the AC outlets
Multi-Zone
Remote Control
•These outlets supply power to external audio equipment.
•Audio equipment with a total power consumption of 120 W (1 A) can be connected.
•The power supply turns on and off together
with the
on the main unit. When set
to “ON”, power is supplied from the outlet.
When set to “STANDBY”, no power is supplied.
Information
NOTE
When “HDMI Control” (vpage 31) is set
to “ON”, power is supplied constantly to
the AC outlet (UNSWITCHED).
Troubleshooting
Set as Necessary
Set this to use the RS-232C connector for the DENON RF remote
controller.
“232C Port” (vpage 35)
Specifications
When using the AVR-2310CI in combination with the DENON RF
remote controller (RC-7000CI, sold separately) or RF remote receiver
(RC-7001RCI, sold separately), two-way communication is enabled.
The AVR-2310CI’s status information as well as iPod and Internet audio
music files can be browsed watching the RF Remote Controller’s
display. For details, refer to the operating instructions of the respective
devices.
NOTE
On the GUI menu, when setting “232C Port” to “2Way Remote”, you
cannot use the RS-232C connector as an external controller (vpage
35).
19
n TRIGGER OUT jacks
The TRIGGER OUT output terminal outputs a maximum 12
V/150 mA electrical signal. When a device with TRIGGER IN
terminal is connected via a monaural mini-plug, the connected
device’s power on/standby can be controlled through linked
operation to the AVR-2310CI.
Set as Necessary
Set to change the conditions for linked operation via the TRIGGER
OUT terminal.
“Trigger Out” (vpage 35)
NOTE
•Insert the AC plugs securely. Incomplete connections could cause
noise.
•Only use the AC outlets to plug in audio equipment. Do not use
them as power supplies for hairdryers or anything other than audio
equipment.
ENGLISH
Selecting the Input Source
Turning the Power On
1
Press
Press
.
The power indicator flashes green and the
power turns on.
Front
The input source can also be selected using the source selection
menu.
when in standby
mode, the power turns on.
When
on
to “MAIN”.
to “MAIN/TV”
to “MAIN”.
Press the SOURCE SELECT button (vpage 7).
The desired input source can be selected directly.
Front
Press
Rear
.
Display the “Source Select” menu.
SOURCE SELECT :SAT/CBL
q
Recent Source
w
Remote Control
This operation can also be performed by pressing a
the main unit.
to “MAIN/TV”
Set
Multi-Zone
has been pressed, the input source set with the
is set. If a
has been pressed, the input source
stored in the memory for the quick select function is set (vpage
55 “Saving frequently used settings (Quick Select Function)”).
1
2
Set
1
2
Playback
b Also press
w Operating on the Main Remote Control Unit
q Using the Source Select Menu
Settings
2
.
The power indicator lights red and the
power is set to the standby mode.
• Use the device selection buttons on the main remote control unit to
set the device to be operated beforehand.
• Input sources that are not going to be used can be set ahead of time.
Make this setting at “Source Delete” (vpage 33).
• To turn off the source selection menu without selecting an input
source, press
again.
Select
ENTER
Enter
e Operating on the Main Unit
2
Front
The power is set to the standby mode.
Press
.
The power indicator turns off, and so does
the power.
• Power continues to be supplied to some of the circuitry even when
the power is in the standby mode. When leaving home for long
periods of time or when traveling, either press
to turn off the
power, or unplug the power cord from the power outlet.
• When the ZONE2 power is switched on, and you want to switch off
the MAIN ZONE power, press
.
Video
:
(SAT/CBL),
Player :
(HDP),
Tuner
:
(TUNER),
iPod
:
b“
(TV),
(DVD),
(VCR),
(CD),
(DVR),
b If “Tuning Preset” mode is selected for
the input source, press
before turning
.
(V.AUX)
Specifications
NOTE
q Input Source : The name of the highlighted input source is
displayed.
w Recently used sources : The currently selected input source is
highlighted.
e Icons for the input sources in the different categories are
displayed.
.
Troubleshooting
1
Press .
Turn
Information
e
Turning the Power Off
(PHONO)
(SIRIUS)
” is displayed when using a Control Dock for
iPod.
3
Use uio
press
Connections
There are three ways to select the input source, as described below.
q Selecting the input source using the Source Select menu (GUI
menu)
w Selecting the input source using the SOURCE SELECT button
(Main remote control unit)
e Selecting the input source using the
(Main unit)
Getting Started
Once Connections are
Completed
p to select the input source icon, then
.
The input source is set and the source selection menu is turned
off.
20
ENGLISH
With the AVR-2310CI, settings and operations for most functions can be performed by operating while looking at the menus displayed on the monitor screen.
Settings
you want to
set, then press
p or
.
ress ui to
3Pselect
the item
you want to
set, then press
p or
.
se uio p to select the item,
4Uthen
press
to set.
bTo return to the previous item, press o or
.
bSelect “Default Yes”, then press
reset to the default setting.
to
⇩
ress ui to
2Pselect
the item
.
The menu is
displayed.
⇩
1Press
n Operations
⇩
Connections
Menu Map
⇩
Getting Started
Settings
5Press
.
The settings made up to
that point are entered and
the settings menu screen
turns off.
Playback
n Setting menus
Setting items
Multi-Zone
MENU
Remote Control
Audio/Video
Adjust
Information
Auto Setup
Manual Setup
Input Setup
Information
Items that only need to be set once
Audio/Video Adjust
Adjust
various
audio/video
parameters.
Information
Show information about receiver
settings, input signals, etc.
Detailed items
Page
Troubleshooting
Specifications
Adjust various audio parameters.
Adjust various video parameters.
48
52
Status
Audio Input Signal
HDMI Information
Shows information about current settings.
Shows information about audio input signals.
Displays the HDMI input/output signals and TV information.
53
53
53
Auto Surround Mode
Quick Select
Preset Channel
Audyssey Auto Setup
Displays the settings stored for the auto surround mode.
Displays the settings stored for the Quick Select function.
Shows information about preset channels.
Makes the optimum settings for the speakers being used
automatically.
Check Audyssey Auto Setup measurement results.
This item is only displayed after the Audyssey Auto Setup procedure
has been performed.
Sets the speaker size and distance, the channel level, etc.
Make settings for HDMI video/audio output.
Make settings for audio playback.
Make settings for audio playback in a ZONE2 system.
Make various other settings.
Change input connector assignment.
Makes the video settings.
Sets the audio input mode and decode mode.
Change the display name for this source.
Adjust the playback level of the audio input.
Make settings for iPod playback.
Use the auto preset function to program radio stations.
Set the preset memories that you do not want to display when tuning.
Assign name to a preset memory.
Set the channel radio reception limits.
Check the SIRIUS radio reception sensitivity.
53
53
53
23
Auto Setup
Makes the optimum speaker
settings and corrects for the acoustic Parameter Check
characteristics of the room.
Set these for example upon purchase.
Once these items are set, there is no need to
Manual Setup
Speaker Setup
set them again unless the speaker layout or the
connected
A d j u s tspeakers
v a r i have
o u s been
a u d changed.
i o a n d v i d e o p a r a m e t e r s Use this to make various types of HDMI Setup
detailed settings.
Audio Setup
Front
ZONE2 Setup
Option Setup
Input Setup
Input Assign
Use this to make settings related to Video
playing input sources.
Input Mode
Rename
Source Level
iPod Playback Mode
Auto Preset
Preset Skip
Preset Name
Parental Lock
Antenna Aiming
21
Description
Audio Adjust
Picture Adjust
27
28
31
32
33
33
37
38
39
39
40
40
40
40
40
41
41
ENGLISH
Getting Started
Examples of GUI Menu Screen Displays
Typical examples are described below.
GExample 1H Top Menu Display
GExample 2H Display when changing settings
GExample 3H Display when inputting characters
Connections
z1
INPUT
INPUT
MENU
z1
Auto
[
HDMI
]
INPUT
z2
[DIGITAL]
[
COMP
]
[
iPod
]
z4
Adjust
Setup
z3
Coax1
None
Opt1
1-RCA
None
None
None
None
None
SAT/CBL
VCR
DVR
HDMI3
None
HDMI4
Coax2
None
Opt2
None
None
2-RCA
None
Assign
None
V.AUX
HDMI5
Opt3
None
None
z5
DVD
Default
z3
z2
Adjust
various
audio
and
video
Change
parameters
Select
ENTER
Enter
RETURN
HDMI input connector assignment
Use p or
to switch.
⇩ Press
INPUT
INPUT
Default
VD
DP
V
AT/CBL
H
H
N
H
D
D
o
D
M
M
n
M
I1
I2
e
I3
]
z6
Cancel
GExample 4H Display when resetting
[DIGITAL]
C
N
O
C
o
o
p
o
a
n
t
a
x1
e
1
x2
[
COMP
1
N
N
N
o
o
o
R
n
n
n
]
[
CA
e
e
e
iPod
None
HDMI4
None
Opt2
None
2-RCA
Assign
None
V.AUX
HDMI5
Opt3
None
None
INPUT
SETUP
RENAME
DVD
z1
DVD
Default
Specifications
Select
ENTER
Enter
RETURN
HDMI input connector assignment
]
None
None
None
None
VCR
DVR
Change
RETURN
z1 : When o p is pressed, the cursor moves to the left or right.
z2 : When ui is pressed at the position at which you want to input the
character, the character is input.
.
SETUP
ASSIGN
HDMI
Enter
Troubleshooting
D
H
T
S
[
ENTER
A/a/!/0
Information
z1 : The menu items are displayed here.
z2 : Guide text for the currently selected setup item.
z3 : The selected line is displayed here.
The currently selected item is displayed on the display.
Use ui to move to the item you want to set.
z4 : Switch to the next item.
SEARCH
Return
z1 : History item.
z2 : Currently selected setup item.
z3 : Operation button guidance.
z4 : Guide text for the currently selected setup item.
z5 : Use uio p to move to the item you want to set.
z6 : o p is displayed at the sides of items whose setting can be changed.
Use o p to change to the desired setting.
Remote Control
z4
Input
Return
Multi-Zone
HDMI1
HDMI2
None
Playback
Manual Setup
Input Setup
z2
DVD
DVD
HDP
TV
z1
SETUP
RENAME
Settings
Default
Audio/Video
Information
SETUP
ASSIGN
ENTER
Enter
z1 : Press i to select “Default”, then press
RETURN
Return
to set.
22
ENGLISH
Getting Started
Making the Optimum Settings for the Connected Speakers Automatically
(Audyssey Auto Setup)
The acoustic characteristics of the connected speakers and listening room are measured and the optimum settings are made automatically.
Connections
n Audyssey Auto Setup Flow
Step 1 : Connect the included Setup
Microphone (vpage 24)
Settings
Playback
Step 2 : Audyssey Auto Setup Preparations
(vpage 24)
Multi-Zone
n Changing the amplifier assignment (Amp Assign)
(vpage 24)
n Set the channel to be measured (Channel Select)
(vpage 25)
Important Information
Remote Control
Audyssey MultEQ® automatically measures the acoustical
problems in the listening environment to create the best audio
experience for your home theater.
• When the Audyssey Auto Setup procedure is performed, the
MultEQ, Dynamic EQ and Dynamic Volume functions (vpage 50)
are enabled.
• Use the included setup microphone (DM-A409) to perform the
Audyssey Auto Setup procedure.
• Measurements are performed by placing the calibrated microphone
successively at multiple positions throughout the listening area as
shown in GExample qH. For best results, it is strongly recommended
to measure 6 positions so that the measurements have the proper
spatial weighting.
Even if the listening environment is small as shown in GExample wH,
measuring at multiple points throughout the listening environment
results in more effective correction.
n When using Front Height Speakers
Step 3 : Performing the Audyssey Auto Setup
Procedure (vpage 25)
GExample qH
FHL
FL
SW
C
FR
GExample wH
FHR
FHL
FL
SW
C
FR
FHR
Information
Results (Parameter Check) (vpage 27)
Troubleshooting
*M
*M
SL
SR
SL
SR
Specifications
n When using Surround Back Speakers
GExample qH
FL
SW
C
GExample wH
FR
FL
SW
C
FR
( : Measuring positions)
SL
SR
SL
SR
*M
*M
23
SBL
SBR
SBL
SBR
: Front height speaker (L)
: Front speaker (L)
: Subwoofer
: Center speaker
: Front speaker (R)
: Front height speaker (R)
: Surround speaker (R)
: Surround back speaker (R)
: Surround back speaker (L)
: Surround speaker (L)
About the main listening position (*M)
The main listening position refers to the most central position where
one would normally sit within the listening environment.
MultEQ uses the measurements from this position to calculate
speaker distance, level, polarity, and the optimum crossover value
for the subwoofer.
NOTE
( : Measuring positions)
n Check Audyssey Auto Setup Measurement
FHL
FL
SW
C
FR
FHR
SR
SBR
SBL
SL
• Loud test sounds may be played during Audyssey MultEQ automatic
speaker setup. This is part of normal operation. If there is background
noise in room, these test signals will increase in volume.
• Do not stand between the speakers and setup microphone or allow
obstacles in the path while the measurements are being made. This
will cause inaccurate readings.
• Make the room as quiet as possible. Background noise can disrupt
the room measurements. Close windows, silence cell phones,
televisions, radios, air conditioners, fluorescent lights, home
appliances, light dimmers, or other devices as measurements may
be affected by these sounds.
Cell phones should be placed away from all audio electronics during
the measurement process as Radio Frequency Interference (RFI)
may cause measurement disruptions (even if the cell phone is not in
use).
ENGLISH
s Audyssey Auto Setup Preparations
a Connect the included Setup Microphone
NOTE
STEP1 Preparation
(vpage 12 “Connecting the Speakers”)
When using a subwoofer, make the following settings before starting
the Audyssey Auto Setup procedure:
Changing the amplifier assignment (Amp Assign)
Set the TV’s input to the AVR-2310CI.
n When using a subwoofer with a direct mode
The signals output from the AVR-2310CI’s SURR. BACK/AMP ASSIGN
speaker terminals can be switched to signals of the surround mode
being used.
Playback
(vpage 20 “Turning the Power On”)
n When using a subwoofer without a direct mode
The Audyssey Auto Setup screen appears automatically.
Set the direct mode to “On” and disable the volume adjustment
and crossover frequency setting.
Make the following settings:
•Volume
: “12 o’clock position”
•Crossover frequency : “Maximum/Highest Frequency”
•Low pass filter
: “Off”
•Standby mode
: “Off”
ui to select
1 Press
“Amp Assign”, then
press
.
AUTO
SETUP
AUDYSSEY
STEP1
Connect
the
and
place
ing
to
in
the
items
Amp
SETUP
[1/6]
accord-
recommendathe
manual.
following
if
nesessary.
Assign
Channel
Auto
Select
Setup
Start
ENTER
Set
Sound
receptor
use
of
surround
back
Enter
ch.
RETURN
for
your
Cancel
system
:The sound of the surround back channel is output
from the speakers connected to the SURR.
BACK/AMP ASSIGN terminals.
ZONE2
:If the ZONE2 power is on, the sound of the
ZONE2 channel is output from the speakers
connected to the SURR. BACK/AMP ASSIGN
terminals.
Front A Bi-Amp :The sound of the front A bi-amp channel is output
Front B Bi-Amp :
The sound of the front B bi-amp channel is output
from the speakers connected to the SURR.
BACK/AMP ASSIGN terminals.
Setup
microphone
Front Height
:The sound of the front height channel is output
from the speakers connected to the SURR.
BACK/AMP ASSIGN terminals.
n To cancel Audyssey Auto Setup
Remote control
operation buttons
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
To cancel, press
then use o p to select “Yes”.
: Decision the setting
: Return to previous menu
24
Specifications
from the speakers connected to the SURR.
BACK/AMP ASSIGN terminals.
Troubleshooting
When installing the setup microphone, adjust its height so that
the section where the sound is received is at the height of the
ears during listening.
Normal
Information
2 Press. o p to select Amp Assign Mode, then press
the setup microphone on a tripod or stand and
5 Mount
install it at the main listening position.
MultEQ
speakers
them
the
ations
Set
AUTO
Preparation
Remote Control
1 Check the speaker connections.
2 Turn on the power of the TV and subwoofer.
3 Turn on the AVR-2310CI’s power.
Connect the included calibrated setup microphone to
4 the
SETUP MIC jack on the main unit.
Multi-Zone
When using a subwoofer on which the volume can
be adjusted and the crossover frequency can be set
Perform the following settings if adjustments, etc., are required for
the speaker environment you’re using.
If you do not need to perform the following settings, or have already
completed them, select “Auto Setup Start” and then press
.
Proceed to “ STEP2 ”.
Settings
•Do not hold the microphone in your hand during measurements.
•Avoid placing the microphone close to a seat back or wall as sound
reflections may give inaccurate results.
Connections
•Do not disconnect the setup microphone until the Audyssey Auto
Setup procedure is completed.
•When using headphones, unplug the headphones before starting
the Audyssey Auto Setup procedure.
around items indicate the settings made upon purchase.
NOTE
Getting Started
Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)
ENGLISH
Getting Started
Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)
Set the channel to be measured (Channel Select)
Connections
T
he front speaker to be measured can be selected ahead of time
here.
•Subwoofer, Surround Back
Settings
If you set the channels you will not use beforehand, those channels
will not be measured. Therefore, you can save an amount of time
commensurate with that which would have been taken to measure
those channels.
Playback
1 “Channel
Press
Select”,
.
• The Audyssey Auto Setup function detects the presence of each
speaker and automatically calculates the speaker size, channel level,
distance, and optimal crossover frequency setting. Audyssey MultEQ
corrects acoustical distortions within the listening area.
• Once started, MultEQ will play a series of test tones through each
speaker.
• Before starting, connect and position all of your speakers.
STEP2 Speaker Detection
ui to select
then press
STEP3 Measurement
d : Perform Audyssey Auto Setup
•Front
AUTO
SETUP
AUDYSSEY
STEP1
SETUP
the
and
place
ing
to
in
the
items
accord-
recommendathe
manual.
following
if
Multi-Zone
Amp
[1/6]
speakers
them
the
ations
Auto
Select
Setup
Start
ENTER
unused
ch’s
1 .
“Measure”
2 Select
and then press
.
Press
ui to select “Auto Setup Start”, then press
Enter
measurement
RETURN
for
Cancel
timesaving.
AUTO
Remote Control
2 the item, and then press
ui to select a channel, press o p to select
AUTO
Speaker
Please
place
the
rophone
at
at
listening
main
SETUP
MultEQ
[2/6]
Detection
ear
mic-
height
Te s t
Information
B
: The sound is output from front speakers B when measuring
the front speakers.
Troubleshooting
A + B : The sound is output simultaneously from front speakers A
and B when measuring the front speakers.
Tone
will
start
for
Enter
Cancel
measurement
AUTO
SETUP
AUDYSSEY
STEP2
Spkr
Front
Measurement”, then
press
.
AUTO
Detect
SETUP
MultEQ
[2/6]
Check
Yes
Center
Yes
Subwoofer
Yes
Surround
Yes
S.Back
Yes
2spkrs
Measurement
ENTER
Goto
Step3
(Measurement)
Enter
after
SETUP
MultEQ
2nd
at
ear
[3/6]
mic-
height
listenimg
position.
Measure
Next
Calculation
ENTER
Start
next
measurement.
Enter
Test
RETURN
Tone
will
Cancel
start
b To skip this step, select “Next 1 Calculation” and proceed to
Perform Step 5 repeatedly for the 3rd, 4th, 5th, and
6 6th
measurements.
position and positions around it. It is possible to stop the settings
with five positions or fewer, but for better results we recommend
measuring at six positions.
STEP4 Calculation
measurements
7 Once
are finished, use
ui to select “Next
RETURN
speaker
Cancel
check
press
.
AUTO
SETUP
AUDYSSEY
STEP3
Please
place
rophone
at
AUTO
2nd
at
the
ear
[3/6]
mic-
listenimg
position.
Next
Calculation
ENTER
Proceed
Specifications
takes several
minutes
to
complete.
The time required for
this analysis depends on
the number of speakers
connected. The greater
the number of speakers
connected, the longer
analysis will take.
When “Amp Assign” is set to “Normal”, only then is “Surround Back”
displayed.
MultEQ
height
to
Step
4
Enter
RETURN
Cancel
(Analyze)
⇩
b Analysis
.
SETUP
Measurement
Measure
Analysis begins.
:Skip the selected channel and do not measure.
b To cancel, press
rophone
the
Measurements for the second position begin.
1 Calculation”, then
Retry
Measure :Default setting. Measure the selected channel.
Skip
RETURN
Once all the speakers have been detected, check the
3 results
of detection of the connected speakers.
ui
to
4 Press
select
“Next
1
Next
n Subwoofer, Surround Back
place
Once measurements for the sixth position are completed,
“Measurements finished.” is displayed.
: The sound is output from front speakers A when measuring
the front speakers.
Please
at
AUTO
Measurement
bMeasure at a total of six positions, including the main listening
ENTER
A
SETUP
AUDYSSEY
Measure
.
n Front
move
the
setup
microphone to the
second
position,
use ui to select
“Measure”,
then
press
.
AUTO
STEP3
SETUP
AUDYSSEY
STEP2
position.
Press
STEP4 .
nesessary.
Assign
Channel
Skip
MultEQ
Preparation
Connect
Set
AUTO
the screen on
5 Once
the right appears,
AUTO
SETUP
AUDYSSEY
STEP4
Now
AUTO
SETUP
MultEQ
Calculation
[4/6]
calculating...
Please
wait.
■■■■■
25%
See overleaf
25
Remote control
operation buttons
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
ENGLISH
n Exiting the GUI Menu
STEP5 Check
AUTO
The measurement result
confirmation screen is
displayed.
AUTO
Check
Check
processing
ults.To
SETUP
MultEQ
[5/6]
res-
proceed,press
"Next"
Spkr
Config
Check
Distance
Check
Ch.Level
Check
Crossover
Next
Check
Store
ENTER
Select
item
to
Enter
RETURN
Cancel
check
•If the result differs from the actual connection status or an error
message appears, use ui to GUI menu “Retry” and then press
to repeat the measurement.
This returns you to analysis results items, so repeat step 8.
.
AUTO
SETUP
AUDYSSEY
STEP6
Store
Press
"Store"
calculation
Storing... Please
wait.” is displayed on the
GUI menu while the results
are being stored.
AUTO
SETUP
MultEQ
[5/6]
to
store
results.
Information
“Now
Remote Control
STEP6 Store
•If the result still differs from the actual connection status after remeasurement or the error message still appears, it is possible that
the speakers are not connected properly. Turn the AVR-2310CI off,
check the speaker connections and repeat the measurement process
from the beginning.
•For instance, If the location or direction of a speaker is altered, the
Audyssey Auto Setup should be performed again to ensure the
correct EQ solution for the new room configuration.
Multi-Zone
9 Press .
10 Press i to select “Next 1 Store”, then press
“Store”, then
11Select
press
.
NOTE
Do not change the speaker connections or subwoofer volume, or
speaker locations after making measurements. If changes are necessary, make the changes and use the Audyssey Auto Setup once again
for an updated EQ solution.
Playback
or
other
speakers may be set to
a value that does not
correspond to the actual
distance.
AUDYSSEY
STEP5
The GUI menu display disappears.
Settings
b Subwoofer
SETUP
while the GUI menu is displayed.
Connections
ui to select the item you want to check, then
8 Use
press
.
Press
Store
ENTER
Apply
and
store
Enter
measurement
RETURN
Cancel
result.
Troubleshooting
NOTE
Do not turn the power off while the settings are being stored.
Remote control
operation buttons
Displaying the menu
: Cancel the menu
Specifications
the setup microphone from the AVR12Disconnect
2310CI.
13Select “Exit” and then press .
Getting Started
Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
26
ENGLISH
Getting Started
Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)
Error Messages
If the Audyssey Auto Setup procedure could not be completed due to speaker installation, the measuring environment, etc., an error message is
displayed. If this happens, check the relevant items, be sure to take the necessary measures, then perform the Audyssey Auto Setup procedure
over again.
Connections
NOTE Be sure to turn the power off before checking the speaker connections.
Error messages (examples)
AUTO
Settings
AUTO
SETUP
No
•Connect the included setup microphone to the
SETUP MIC jack on the main unit.
•Check the speaker connections.
MultEQ
Caution!
microphone
or
•Not all speakers could be detected.
•The front L speaker was not properly detected.
Speaker
This is displayed after the Audyssey Auto Setup procedure is
completed.
Press ui to select
1 “Parameter
Check”,
Measures
•Included setup microphone is not connected.
SETUP
AUDYSSEY
Cause
Check Audyssey Auto Setup
Measurement Results (Parameter Check)
then press p or
.
AUTO
SETUP
PARAMETER
Speaker
Distance
Channel
Check
Check
Level
Crossover
EQ
CHECK
Config
Check
Check
Check
Restore
Playback
Show
speaker
configuration
result
Retry
Front
RETURN
Check
cause
Multi-Zone
AUTO
of
Cancel
problem!
•Too much noise in the room for accurate
measurements to be made.
SETUP
AUDYSSEY
AUTO
SETUP
Ambient
noise
MultEQ
Caution!
or
Level
is
is
too
too
high
low
Remote Control
•Speaker or subwoofer sound is too low for
accurate measurements to be made.
Retry
RETURN
Check
cause
AUTO
of
AUTO
SETUP
MultEQ
Information
R
None
Retry
Troubleshooting
ENTER
Check
cause
AUTO
of
Enter
RETURN
Cancel
problem!
SETUP
AUDYSSEY
L
AUTO
SETUP
MultEQ
•Displayed speaker could not be detected.
· The front R speaker were not properly detected.
· Only one channel of the surround speakers was
detected.
· Sound was output from the R channel when only
one surround back speaker was connected.
· The surround back, but the surround speaker was
not detected.
•Check the
speaker.
•Displayed speaker connected with the polarities
reversed.
•Check the polarities of the displayed speaker.
•For some speakers, this error message may
be displayed even if the speaker is properly
connected. If you are sure that the wiring is
correct, press ui to select “Skip”, then press
.
Phase
Specifications
Retry
connections
of
the
ENTER
cause
of
Enter
RETURN
Channel Level Check
displayed
: Check the distance
: Check the channel level
Crossover Freq. Check :Check the crossover frequency
EQ Check
: Check the equalizer
o p to switch the display between the different
3 Use
speakers.
4 Press .
Skip
Check
Speaker Config. Check :Check the speaker configuration
Distance Check
Caution!
Front
Cancel
Caution!
Front
ui to select the item you want to check, then
2 Use
press p or
.
problem!
SETUP
AUDYSSEY
•Either turn off any device generating noise or
move it away.
•Try again when the surroundings are quieter.
•Check the speaker installation and the direction
in which the speakers are facing.
•Adjust the subwoofer’s volume.
Cancel
problem!
The confirmation screen reappears. Repeat steps 2 and 3.
Even if the settings are changed after the Audyssey Auto Setup
procedure, the Audyssey Auto Setup settings can be restored by
selecting “Restore” then pressing
.
n To perform the Audyssey Auto Setup procedure again
Press ui to select “Retry”, then press
.
n To cancel Audyssey Auto Setup
Press
, the “Cancel auto setup?” prompt is displayed.
Press o p and select “Yes”, then press
.
27
Remote control
operation buttons
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
ENGLISH
Making the speaker settings (Speaker Setup)
Default settings are underlined.
Use this procedure to set the speakers manually or if you wish to change the settings made with
the Audyssey Auto Setup procedure.
n Items that can be set with the Manual Setup procedure
Amp Assign
Sets the signal output to the
speaker connected to the
SURR. BACK/AMP ASSIGN
terminals.
Normal :The surround back channel audio signals are output.
ZONE2 :The ZONE2 audio signals are output.
Front A Bi-Amp : The bi-amp audio signals are output. Set this for bi-amp
playback of the front A speakers.
Front B Bi-Amp : The bi-amp audio signals are output. Set this for bi-amp
playback of the front B speakers.
Front Height : The front height channel audio signals are output.
Speaker Config.
Making the ZONE2 settings (ZONE2 Setup) vpage 33
n Examples of Menu Screen Displays
Speaker Setup
SPEAKER
Amp
S
B
D
C
p
a
i
h
e
s
s
a
SETUP
HDMI
SETUP
Assign
aker Config.
s Setting
tace
nnel Level
Crossover
Front
SETUP
RGB Range
Auto Lip Sync
Normal
ON
EXT.IN SW Level
2ch Direct/Stereo
Audio Out
HDMI Control
AMP
OFF
Auto
EQ
Surround
NOTE
Mode
Customize
Frequency
Speaker
surround
Setup
back
AMP
for
other
Use
use
video
range
from
16
(black)
RETURN Return
to 235 (white)
ZONE2 Setup
Lch
0dB
Relative
Volume Limit
Power On Level
Mute Level
OFF
Last
Full
MANUAL
SETUP
OPTION
SETUP
Volume
Source
0dB
Level Rch
Volume Display
left
channel
Remote control
operation buttons
output
level
in
EXT.
IN
mode
When “Front” is set to “Small”, “Subwoofer” can automatically set
to “Yes”.
On-Screen Display
Quick Select Name
Zone Rename
Trigger
RETURN
the
playback
Control
Delete
Out
Remote ID
232C Port
Adjust
subwoofer
Option Setup
MANUAL SETUP
ZONE2 SETUP
Level
Set
Select “Large” or “Small” not
according to the physical size
of the speaker but according
to
the
low
frequency
reproduction
capabilities
based on the frequency set
at “Crossover Frequency”
(vpage 30).
• “Large” is not displayed when “Front” is set to “Small”.
• Even if “Center” has been set to “Large”, when “Front” is set to
“Small”, the “Center” setting automatically switches to “Small”.
Subwoofer : Set the presence of a subwoofer.
• Yes : Use a subwoofer.
• No : Select when a subwooofer is not connected.
level
Setup
Return
Make
settings
for
volume
Displaying the menu
: Cancel the menu
See overleaf
control
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
2
Specifications
Assign
Audio Setup
MANUAL SETUP
AUDIO SETUP
SETUP
Troubleshooting
MANUAL
HDMI Setup
MANUAL
Information
If “Subwoofer” is set to “No”, “Front” is automatically set to “Large”.
Center : Set the presence and size of the center speaker.
• Large : Use of a large speaker that can adequately play back low
frequencies.
• Small : Use of a small speaker that has inadequate playback capacity for
low frequencies.
• None : Select when a center speaker is not connected.
Making other settings (Option Setup) vpage 33
Remote Control
Front : Set the front speaker size.
Select speaker configuration • Large : Use of a large speaker that can adequately play back low
frequencies.
and size.
(bass reproduction capability) • Small : Use of a small speaker that has inadequate playback capacity for
low frequencies.
Multi-Zone
Making the audio settings (Audio Setup) vpage 32
Setting contents
Playback
Making the HDMI settings (HDMI Setup) vpage 31
Setting items
Settings
Making the speaker settings (Speaker Setup) vpage 28
Connections
Use this procedure to change the Audyssey Auto Setup settings or to change the various audio,
video and display settings.
The set can be used without changing these settings. Make these settings as necessary.
For a description of “Menu Map” and operating instructions, see page 21.
Getting Started
Making detailed settings (Manual Setup)
ENGLISH
Getting Started
Making detailed settings (Manual Setup)
Setting contents
Setting items
Speaker Config.
Connections
Surround : Set the presence and size of the Surround speakers.
Select speaker configuration • Large : Use of a large speaker that can adequately play back low
frequencies.
and size.
(bass reproduction capability) • Small : Use of a small speaker that has inadequate playback capacity for
low frequencies.
• None : Select when the surround speakers are not connected.
Settings
Playback
“S.Back” is displayed
when the “Amp Assign”
setting (vpage 28) is
set to “Normal”.
Multi-Zone
“Large” is not displayed when “Front” is set to “Small”.
S.Back : Set the presence, size and number of surround back speakers.
• Large : Use of a large speaker that can adequately play back low
frequencies.
• Small : Use of a small speaker that has inadequate playback capacity for
low frequencies.
• None : Select when the surround back speakers are not connected.
• 2sp : Use two surround back speakers.
• 1sp : Use only one surround back speaker. Surround back audio is output
from the surround back L terminal.
Remote Control
•“Large” is not displayed when “Surround” is set to “Small”.
•Even if “S.Back” is set to “Large”, the “S.Back” setting is automatically
switched to “Small” if “Surround” is set to “Small”.
NOTE
Information
Troubleshooting
“Front
Height”
is
displayed when the “Amp
Assign” setting (vpage
28) is set to “Front
Height”.
Specifications
NOTE
Even when the Surround Back Speaker setting is other than “None”,
sound may not be emitted from the surround back speaker, depending
on the playback source. In this case, “Surround Back” setting other
than “OFF” (vpage 49).
Front Height : Set the front height speaker size.
• Large : Use of a large speaker that can adequately play back low
frequencies.
• Small : Use of a small speaker that has inadequate playback capacity for
low frequencies.
• None : Select when a front height speaker is not connected.
Select “Large” or “Small” not
according to the physical size
of the speaker but according
to
the
low
frequency
reproduction
capabilities
based on the frequency set
at “Crossover Frequency”
(vpage 30).
29
Remote control
operation buttons
Bass Setting
Subwoofer Mode : Select low range signal to be reproduced by
Make the settings related to subwoofer.
playback of low frequency • LFE : Add the low frequency signal of the channel for which the speaker
signals (subwoofer and LFE). size is set to “Small” to the subwoofer signal and output it.
• LFE+Main : Add the low frequency signal of all channels to the subwoofer
This can be set when
signal and output it.
“Speaker
Config.”
–
•Play music or a movie source and select the mode offering the
“Subwoofer” (vpage
strongest bass.
28) is set to “Yes”.
•Select “LFE+Main” if you want the bass signals to always be
produced from the subwoofer.
LPF for LFE : Set the upper limit of the low frequency signals output from
the subwoofer.
• 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / 250Hz
Unit : Set the unit of distance.
Distance
Set the distance from the • Feet
listening position to the • Meters
Step : Set the minimum variable width of the distance.
speakers.
Measure the distance from • 1ft / 0.1ft
the listening position to the • 0.1m / 0.01m
speakers beforehand.
• FL (Front L)/ FR (Front R)/ C (Center)/ SW (Subwoofer)/ SL (Surround L)/
SR (Surround R/ SBL (Surr. Back L)/ SBR (Surr. Back R)/ FHL (Front Height L)/
FHR (Front Height R) : Select the speaker you want to set, and set the
distance. Set the value that is closest to the measured distance.
• 0.0ft ~ 60.0ft / 0.00m ~ 18.00m
•“Large” is not displayed when “Front” is set to “Small”.
•Even if “Front Height” is set to “Large”, the “Front Height” setting
is automatically switched to “Small” if “Front” is set to “Small”.
Displaying the menu
: Cancel the menu
Setting contents
Setting items
: Moves the cursor (Up/Down/Left/Right)
•The speakers that can be selected differ depending on the “Amp Assign”
(vpage 28) and “Speaker Config.” (vpage 29) settings.
•Default settings :
Front/Center/Subwoofer/Front Height : 3.6 meters (12 feet)
Surround/Surr. Back : 3.0 meters (10 feet)
NOTE
Set the difference in the distance between the speakers to less than 6.0
meters (20 feet). “Relocate Speaker” is displayed on the screen if an
inappropriate distance is set.
Default : Reset all distance settings to factory default.
• Yes : Reset to the defaults.
• No : Do not reset to the defaults.
: Decision the setting
: Return to previous menu
ENGLISH
Setting contents
Setting items
Channel Level
Specifications
Remote control
operation buttons
Troubleshooting
NOTE
•When set to “Custom”,
does not operate.
•The front speaker setting stored for the “Quick Select” function is given
priority.
Information
This can be set when
“Speaker Config.” –
“Subwoofer” (vpage
28) is set to “Yes” or
“No”.
MULTI CH : The front speakers used in modes other than the direct, stereo
and pure direct play modes are set in advance.
• A : Front speaker A is used.
• B : Front speaker B is used.
• A+B : Both front speakers A and B are used.
Remote Control
Outputs at below set
frequency, each speaker’s
bass signal output from the
subwoofer. Set this according
to the low frequency
reproduction capabilities of
the speakers you are using.
Default : Reset all channel level settings to factory default.
• Yes : Reset to the defaults.
• No : Do not reset to the defaults.
Crossover : Outputs at below set frequency, each speaker’s bass signal
output from the subwoofer.
• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
250Hz
• Advanced : Set the low frequency signals to be output from the signals
of the respective speakers to the subwoofer.
• Front / Center / Surround / S.Back / Front Height : Select the speaker.
· 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
250Hz : Set the crossover frequency.
2CH DIRECT/STEREO : The front speakers used in the direct, stereo and
pure direct play modes are set in advance.
• A : Front speaker A is used.
• B : Front speaker B is used.
• A+B : Both front speakers A and B are used.
Multi-Zone
Crossover Frequency
•Always set the crossover frequency to “80 Hz”. When using small
speakers, however, we recommend setting the crossover frequency
to a higher frequency.
•For speakers set to “Small”, sound below the crossover frequency
is cut from the sound output. The cut bass sound is output from the
subwoofer or front speakers.
•The speakers that can be set when “Advanced” is selected differ
according to the “Bass Setting” setting (vpage 29).
· When “LFE” is selected, speakers set to “Small” at “Speaker
Config.” (vpage 28) can be set.
· When “LFE+Main” is selected, speakers can be set regardless of
the speaker size setting.
Setting : Choose the method for setting the front speakers.
Front Speaker Setup
.
Select front speakers to use • Normal : The front speakers are set using the
• Custom : The front speakers used for the different playing modes are
for each surround mode.
set in advance.
Playback
•When “Channel Level” is adjusted, the adjusted values are set for
all the surround modes. To adjust the channel level separately for the
different surround modes, use the operation see “Adjust the volume of
the different speakers” (vpage 55).
•Speakers set to “None” in the “Speaker Config.” (vpage 28) settings
are not displayed.
•When o is pressed while the subwoofer volume is set to “–12dB”, the
“Channel Level” setting switches to “OFF”.
•If output of the test tones begins while the muting mode is set, the
muting mode is canceled.
Crossover Frequency
Settings
Test Tone Start : Output test tones.
FL (Front L)/ C (Center)/ FR (Front R)/ SR (Surround R)/
SBRz (Surround Back R)/ SBLz (Surround Back L)/ SL (Surround L)/
FHL (Front Height L)/ FHR (Front Height R)/ SW (Subwoofer) : Select
the speaker.
zWhen the “S.Back” setting (vpage 29) is set to “1sp”, “SB” is
displayed.
• –12.0dB ~ +12.0dB (0.0dB) : Adjust the volume.
Connections
Set the volume of the test
tone to be the same when it
is output from each speaker.
Setting contents
Setting items
Getting Started
Making detailed settings (Manual Setup)
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
30
ENGLISH
Getting Started
Making detailed settings (Manual Setup)
Setting items
Making the HDMI settings(HDMI Setup)
Default settings are underlined.
Connections
Make settings for HDMI video/audio output.
Setting items
Settings
Playback
Multi-Zone
RGB Range
Set the video range of RGB
output from the HDMI
terminal.
Auto Lip Sync
Automatic
compensation
for timing shift in audio and
video output.
HDMI Audio Out
Select HDMI audio output
device.
Setting contents
Normal : Output with RGB video range (16 (black) to 235 (white)).
Enhanced : Output with RGB video range (0 (black) to 255 (white)).
This setting is valid when using a TV equipped with a DVI terminal.
ON : Compensated.
OFF : Not compensated.
Amp : Use speakers connected to AVR-2310CI for audio playback.
TV : Use speakers of TV for audio playback.
Setting contents
Standby Source
Last : Standby with last used input source during power on.
Set the HDMI connector for HDMI1 / HDMI2 / HDMI3 / HDMI4 / HDMI5 : The standby mode is set at
HDMI signal input during the input source assigned to the respective.
standby.
This can be set when
“HDMI Control” is set
to “ON”.
Power Off Control
ON:Switched.
The power of the AVR-2310CI OFF:Not switched.
and external device turn off
• Please consult the operating instructions for each connected device
together.
to check the settings.
• For details on the HDMI control function, see “Controlling HDMIThis can be set when
compatible devices from the AVR-2310CI (HDMI Control Function)”
“HDMI Control” is set
to “ON”.
(vpage 54).
NOTE
Remote Control
Information
When the HDMI control function is operating, the setting of audio playback
in the connected TV takes priority (vpage 54 “Controlling HDMIcompatible devices from the AVR-2310CI (HDMI Control Function)”).
HDMI Control
ON : Use the HDMI control function.
External devices can be OFF : Do not use the HDMI control function.
controlled from the AVR• Please consult the operating instructions for each connected device
2310CI and the AVR-2310CI
to check the settings.
can be controlled from
•
For details on the HDMI control function, see “Controlling HDMIexternal devices.
compatible devices from the AVR-2310CI (HDMI Control Function)”
(vpage 54).
NOTE
Troubleshooting
Specifications
The
HDMI
control
function
controls
operations of a TV that
is compatible with the
HDMI control function.
Make sure that the TV
and HDMI are connected
when you perform HDMI
control.
3
NOTE
• When “Control” is set to “ON”, it consumes more standby power.
• When not using this unit for a long period, we recommend that you press
to turn off (jOFF) the power.
• When the “HDMI Control” setting has been changed, always turn off the
power to the connecting devices afterwards and then turn back on.
• The “HDMI Control” does not work when the power to the equipment is
off.
• When “HDMI Control” is set to “ON”, power is supplied constantly to the
AC outlet (UNSWITCHED).
Remote control
operation buttons
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
ENGLISH
Making the audio settings (Audio Setup)
Default settings are underlined.
+15dB : This is the recommended level.
+10dB / +5dB / 0dB : Select the level according to the player being used.
Troubleshooting
Specifications
: Moves the cursor (Up/Down/Left/Right)
NOTE
• Set so that the “Audyssey Byp. L/R” and “Audyssey Flat” settings can be
made when the Audyssey Auto Setup procedure is performed.
• Equalizer settings for which “Not Used” is set with the Quick Select
function cannot be stored and called out.
Information
Displaying the menu
: Cancel the menu
NOTE
When playing in the PURE DIRECT mode, the surround mode does not
change even if the input signal is changed.
EQ Customize
Audyssey Byp. L/R / Audyssey Flat / Manual
Set so that unused equalizer • Used
settings are not displayed • Not Used
when
is used.
Remote Control
Remote control
operation buttons
The auto surround mode function lets you store in the memory the
surround mode last used for playing the four types of input signals
listed below.
q Analog and PCM 2-channel signals
w Dolby Digital and DTS 2-channel signals
e Dolby Digital and DTS multi-channel signals
r Multi-channel signals other than Dolby Digital and DTS (PCM, etc.)
Multi-Zone
Setting : Select the method for setting the speakers used in the 2-channel
direct and stereo playback modes.
• Basic : The settings at “Speaker Setup” (vpage 28) are applied.
• Custom : Make separate settings for 2-channel mode.
Front : Set the front speaker size.
• Large : Use of a large speaker that can adequately play back low
frequencies.
• Small : Use of a small speaker that has inadequate playback capacity
for low frequencies.
SW : Set the presence of a subwoofer.
• Yes : Use a subwoofer.
• No : Select when a subwoofer is not connected.
SW Mode : Select low range signal to be reproduced by subwoofer.
• LFE : Add the low frequency signal of the channel for which the speaker
size is set to “Small” to the subwoofer signal and output it.
• LFE+Main : Add the low frequency signal of all channels to the
subwoofer signal and output it.
Crossover : Outputs at below set frequency, each speaker’s bass signal
output from the subwoofer.
• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz
/ 250Hz
Distance FL / Distance FR : Select the speaker you want to set, and set
the CH Level. Set the value that is closest to the measured distance.
• 0.0ft ~ 60.0ft (12.0ft) / 0.00m ~ 18.00m(3.6m)
CH Level FL/ CH Level FL FR : Select the speaker you want to set, and
set the CH Level. Adjust the level of each channel.
• –12.0dB ~ +12.0dB(0.0dB)
ON : Memorize settings. Most recently stored surround mode is
automatically selected.
OFF : Do not memorize settings. Surround mode does not change
according to input signal.
Playback
Setting contents
Auto Surround Mode
Make setting for memorizing
surround mode setting for
each input signal type.
Settings
Setting items
EXT.IN SW Level
Set the playback level of the
analog subwoofer signals
input from the external input
terminals (EXT. IN).
2CH DIRECT/STEREO
Make speaker settings for 2channel mode playback.
Setting contents
Connections
Make settings for audio playback.
Setting items
Getting Started
Making detailed settings (Manual Setup)
: Decision the setting
: Return to previous menu
32
ENGLISH
Getting Started
Making detailed settings (Manual Setup)
Making the ZONE2 settings (ZONE2 Setup)
Making other settings (Option Setup)
Default settings are underlined.
Connections
Make settings for audio playback in a ZONE2 system.
“ZONE2 Setup” is displayed when ZONE2 is selected with “Amp Assign” (vpage 28).
Setting items
Settings
Playback
Multi-Zone
Level Lch
Adjust the left channel output
level.
Level Rch
Adjust the right channel
output level.
Volume Display
Set the ZONE2 volume
display method.
Setting contents
–12dB ~ +12dB (0dB)
–12dB ~ +12dB (0dB)
Remote Control
Information
Relative : The volume is displayed within the range of – – –dB (Minimum),
–80 dB ~ +18 dB.
Absolute : The volume is displayed within the range of 0, 1 ~ 99.
Vol.Limit
OFF : Do not set a maximum volume.
Make a setting for maximum –20dB(61) / –10dB(71) / 0dB(81)
volume.
Power On Level
Last : Use the memorized setting from the last session.
Define the volume setting – – – : Always use the muting on condition when power is turned on.
that is active when the power –80dB(1) ~ +18dB(99) : The volume is adjusted to the set level.
is turned on.
Mute Level
Full : The sound is cut off entirely.
Set the amount of attenuation –40dB : The sound is attenuated by 40 dB.
when muting is on.
–20dB : The sound is attenuated by 20 dB.
Troubleshooting
• The volume is displayed using the display method set at “Volume Display” (vpage 33).
•Set the main volume at “Volume Control” (vpage 33).
Default settings are underlined.
Setting items
Setting contents
Volume Control
Volume Display : Set the volume display method.
Set the MAIN ZONE volume • Relative : The volume is displayed within the range of – – –dB (Minimum),
setting.
–80.5 dB ~ +18 dB.
• Absolute : The volume is displayed within the range of 0, 1 ~ 99.
Vol.Limit : Make a setting for maximum volume.
• OFF : Do not set a maximum volume.
• –20dB(61) / –10dB(71) / 0dB(81)
Power On Level : This sets the volume set when the MAIN ZONE’s power
is turned on.
• Last : Use the memorized setting from the last session.
• – – – : Always use the muting on condition when power is turned on.
• –80dB(1) ~ +18dB(99) : The volume is adjusted to the set level.
Mute Level : This sets the amount of attenuation of the volume when the
mute mode is set in the MAIN ZONE.
• Full : The sound is cut off entirely.
• –40dB : The sound is attenuated by 40 dB.
• –20dB : The sound is attenuated by 20 dB.
Source Delete
TUNER / PHONO / CD / DVD / HDP / TV / SAT/CBL / VCR / DVR /
Remove
input
sources V.AUX / SIRIUS: Select the sources you do not want to use.
that are not used from the • ON : Use this source.
display.
• Delete : Do not use this source.
NOTE
•The currently selected input source cannot be set.
•Input sources set to “Delete” cannot be selected using
.
Specifications
GUI
Screensaver : Make screensaver settings.
Make the settings related to • ON : The screen switches to the screensaver if no operation is performed
displays on the TV screen.
for approximately 3 minutes while a menu is displayed or while an iPod
screen is displayed. When you press uio p, the screen saver is
cancelled and the screen before that screen saver started is displayed.
• OFF : Turn the screensaver function off.
Wall Paper : Set wallpaper to display the background when playback is
stopped, etc.
• Picture : Set the background to a picture (DENON logo).
• Black : Set the background to black.
See overleaf
33
Remote control
operation buttons
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
ENGLISH
Setting items
Setting contents
Setting items
The “Format” can also be set by the following procedure. However,
the GUI screen is not displayed.
Quick Select Name
Rename Label : Change the display name of the selected “Quick Select”
Change the Quick Select setting.
1.Use ui to select the name of the Quick Select setting you want
name.
to change, then press
.
2.Use o p to set the cursor to the character you want to change.
3.Use ui to change the character, then press
.
When a format other than the video format of the connected TV is set, the
picture will not be displayed properly.
Zone Rename
1.Use ui to select the zone name you want to change, then press
Rename the display names
.
of the different zones as
MAIN ZONE / ZONE2
desired.
2.Use o p to set the cursor to the character you want to change.
3.Use ui to change the character, then press
.
Troubleshooting
iPod Information : This sets the time the GUI menu is displayed when an
iPod operation is performed.
• Always : Show display continuously.
• 30sec : Show display for 30 seconds after operation.
• 10sec : Show display for 10 seconds after operation.
• OFF : Turn display off.
GUpper case charactersH ABCDEFGHIJKLMNOPQRSTUVWXYZ
GLower case charactersH abcdefghijklmnopqrstuvwxyz
GSymbolsH ! “ # $ % & ‘ ( ) * + , - . / : ; < = > ? @ [ \ ] ^ _ ` { | } ˜
GNumbersH 0123456789 (Space)
Information
Tuner Information : This sets the time the GUI menu is displayed when a
tuner operation is performed.
• Always : Show display continuously.
• 30sec : Show display for 30 seconds after operation.
• 10sec : Show display for 10 seconds after operation.
• OFF : Turn display off.
• Up to 10 characters can be input.
• The input character type can be switched by pressing
while the
display name is being changed.
• The types of characters that can be input are as shown below.
Remote Control
Master Volume : Master volume display during adjustment.
• Bottom : Displayed at the bottom of the screen.
• Top : Displayed at the top of the screen.
• OFF : Turn display off.
4.Repeat steps 2 and 3 to change the display name.
Multi-Zone
Text : The mode name is displayed when the operation for switching the
surround mode, input mode, etc., is performed.
• ON : Turn display on.
• OFF : Turn display off.
Playback
GUpper case charactersH ABCDEFGHIJKLMNOPQRSTUVWXYZ
GLower case charactersH abcdefghijklmnopqrstuvwxyz
GSymbolsH ! “ # $ % & ‘ ( ) * + , - . / : ; < = > ? @ [ \ ] ^ _ ` { | } ˜
GNumbersH 0123456789 (Space)
NOTE
Settings
• Up to 16 characters can be input.
• The input character type can be switched by pressing
while the
display name is being changed.
• The types of characters that can be input are as shown below.
1.Press and hold o on the main unit and
for at least 3 seconds.
“Video Format” appears on the display.
2.Press o p and set the video signal format.
3.Press
,
or
to complete the setting.
Connections
GUI
Format : Set the video signal format to be output for the TV you are
Make the settings related to using.
displays on the TV screen.
• NTSC : Select NTSC output.
• PAL : Select PAL output.
Setting contents
Getting Started
Making detailed settings (Manual Setup)
4.Repeat steps 2 and 3 to change the display name.
Specifications
See overleaf
Remote control
operation buttons
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
34
ENGLISH
Getting Started
Making detailed settings (Manual Setup)
Setting items
Setting contents
Connections
Settings
Trigger Out
n When Setting for Zone (MAIN ZONE / ZONE2)
Select the condition for
Trigger out is activated through linkage to the power of the zone set to
activating Trigger Out for
“ON”.
the input source, surround
n When Setting for Input Source
mode, etc.
Activate trigger out when the input source set to “ON” is selected.
See “TRIGGER OUT jacks”
(vpage 19) for more
Valid for the zone set to “ON” with “When Setting for Zone”.
information on trigger out.
n When Setting for Surround Mode
Activate trigger out when the surround mode set to “ON” is selected.
Playback
alid when the “MAIN ZONE” set to “ON” with “When Setting
V
for Zone” is selected, and when the input source set to “ON” with
“When Setting for Input Source” is selected.
Multi-Zone
Remote Control
Remote ID
1/2/3/4
Set when you operate
When using the AVR-2310CI with only the included remote control unit
another DENON AV amplifier
(RC-1117), use Remote ID “1” (default).
with the remote control unit
When using a separately sold remote control unit (RC-7000CI, etc.),
of the AVR-2310CI. Match
this function can be used. Match the ID setting of the remote control
the remote control unit you
unit and the receiver.
are using with the remote ID
of the AVR-2310CI.
Information
232C Port
Serial Control : Set when using an external controller.
Set when using an external 2Way Remote : Set when using a 2-way remote control unit.
controller or two-way remote
When using a DENON two-way remote control (RC-7000CI or RCcontrol connected to the RS7001RCI, sold separately), set to “2Way Remote”.
232C terminal.
NOTE
Troubleshooting
When setting to “2Way Remote”, you can not use the RS-232C connector
as an external controller.
Dimmer
• Bright : Normal display brightness.
Adjust display brightness of • Dim : Reduced display brightness.
the receiver.
• Dark : Very low display brightness.
• OFF : Turns the display off.
Specifications
Setup Lock
Protect
settings
inadvertent change.
35
Switching is also possible by pressing
• ON : Turn protection on.
from • OFF : Turn protection off.
Remote control
operation buttons
on the main unit.
When “Setup Lock” is set to “ON”, the settings listed below can
no longer be changed. Also, “SETUP LOCKED!” is displayed if you
attempt to operate related settings.
・RESTORER
・Dynamic Volume
・MultEQ
・Channel Level
・Dynamic EQ
・Audio Delay
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
ENGLISH
Default
[
INPUT
VIDEO
SETUP
ASSIGN
HDMI
]
[DIGITAL]
[
COMP
]
[
iPod
Input Mode
INPUT
INPUT
Video
Select
Source
HDMI1
HDMI2
Coax1
None
1-RCA
None
None
None
Video Convert
i/p Scaler
ON
Analog
TV
None
Opt1
None
None
H
N
H
H
C
N
O
O
N
N
2
N
N
A
N
N
Resolution(Analog)
Resolution(HDMI)
Auto
Auto
Progressive
Aspect
Auto
Full
S
V
D
V
A
C
V
.
T/CBL
R
R
AUX
D
o
D
D
M
n
M
M
I3
e
I4
I5
Select
Change
HDMI
o
o
p
p
a
n
t
t
ENTER
input
x2
e
2
3
o
o
o
n
n
R
n
Enter
connector
e
e
CA
e
RETURN
o
s
o
o
n
s
n
n
e
ign
e
e
Mode
Inupt Mode
Decode Mode
&
Select
desired
Rename
video
input
Return
source
RETURN
Automatically
Source Level
INPUT
RENAME
SOURCE
DVD
Analog
input
signal
and
Return
playback
SETUP
PLAYBACK
LEVEL
Input
detect
iPod Playback Mode
INPUT
SETUP
Input
Digital
Auto
Auto
HDMI
RETURN
Return
assignment
SETUP
DVD
SETUP
MODE
]
DVD
HDP
INPUT
Making the video settings (Video) vpage 38
Video
SETUP
Playback
Changing the Input Sources Assigned to the Input Terminals
(Input Assign) vpage 37
Assign
INPUT
INPUT
MODE
0dB
Repeat
OFF
0dB
Shuffle
OFF
Settings
n Items that can be set with the Input Setup procedure
n Examples of Menu Screen Displays
Connections
Make the settings related to the currently selected input source.
Before displaying the menu screen, press
to switch to the input source to be set.
The items that can be set differ according to the selected input source.
The set can be used without changing these settings. Make these settings as necessary.
For a description of “Menu map” and operating instructions, see page 21.
Getting Started
Making the Input Settings (Input Setup)
Default
RETURN
Return
Compensate
INPUT
AUTO
PRESET
auto
preset
Enter
RETURN
Block
A1
FM
A2
FM
A
ON
A1
A2
FM
FM
87.50MHz
89.10MHz
ON
ON
A3
A3
A4
A5
FM
FM
FM
98.10MHz
107.90MHz
90.10MHz
ON
ON
ON
A4
A5
A6
A6
AM
90.10MHz
ON
A7
A8
AM
AM
90.10MHz
90.10MHz
ON
ON
A7
A8
RETURN
Change
memory
Lock
[1/7]
A
[
[
]
]
FM
98.10MHz
[
]
FM
FM
AM
107.90MHz
90.10MHz
90.10MHz
[
[
[
]
]
]
AM
AM
90.10MHz
90.10MHz
[
[
]
]
RETURN
Change
memory
Return
blocks
Antenna Aiming
Troubleshooting
Setting
Edit
NAME
87.50MHz
89.10MHz
Return
blocks
Parental Lock
Lock
Return
mode
SETUP
PRESET
[1/7]
Presets
INPUT SETUP
PARENTAL LOCK
Setting the Preset Channels to be Skipped (Preset Skip) vpage 40
repeat
Preset Name
Block
A Block
Return
process
Presetting Radio Stations (Auto Preset) vpage 40
RETURN
Cancel
INPUT SETUP
ANTENNA AIMING
Satellite
Code
Terrestrial
Assign Name to a Preset Memory (Preset Name) vpage 40
a
listening
limit
to
any
channel
Adjust
antenna
position
for
best
RETURN
signal
Specifications
Set
Information
ENTER
the
RETURN Return
playback level
INPUT
INPUT SETUP
PRESET SKIP
Start
Start
input
Preset Skip
SETUP
Setting the iPod Playback Mode (iPod Playback Mode) vpage 40
audio
Remote Control
Auto Preset
Changing the Input Source’s Display Name (Rename) vpage 39
Correcting the Input Source’s Playback Level (Source Level)
vpage 40
analog
Multi-Zone
Changing the Input Source’s Input Mode and Decoding mode
(Input mode) vpage 39
Return
Setting Radio Reception Restrictions (Parental Lock) vpage 41
Check the SIRIUS Radio Reception Sensitivity (Antenna Aiming)
vpage 41
3
ENGLISH
Getting Started
Making the input settings (Input Setup)
Setting items
Changing the Input Sources Assigned to the
Input Terminals (Input Assign)
Default settings are underlined.
Connections
Setting items
Setting contents
Settings
Input Assign (HDMI)
TV
SAT/CBL VCR
DVR V.AUX input
HDMI : The DVD HDP
Assign input sources to input
sources are assigned to the HDMI input terminals as shown below.
connectors.
• HDMI1 / HDMI2 / HDMI3 / HDMI4 / HDMI5
• None : Do not assign an HDMI input terminal to the currently selected
input source.
Setting contents
Input Assign (Component)
TV
SAT/CBL VCR DVR V.AUX
Component : The DVD HDP
Assign input sources to input
input sources are assigned to the component video input terminals as
connectors.
shown below.
● 1-RCA (Component video 1 input terminal) / 2-RCA (Component video
2 input terminal)
● None : Do not assign the component video input terminals to the currently
selected input source.
bUpon purchase, the settings of the different input sources are as shown
below.
Playback
bUpon purchase, the settings of the different input sources are as shown
below.
Multi-Zone
Input
source
Default
setting
DVD
HDP
HDMI1 HDMI2
TV
SAT/CBL
VCR
DVR
V.AUX
None
HDMI3
None
HDMI4
HDMI5
Remote Control
Information
•When HDMI is assigned to an input source, the audio signal switches
to HDMI along with the video signal. To use with the digital audio
input connectors assigned, set menu “Input Mode” (vpage 39) to
“Digital”.
•When the AVR-2310CI and TV are connected with an HDMI cable, if the
TV is not compatible with HDMI audio signal playback, only the video
signals are output to the monitor.
•The audio signals input from the analog, digital and EXT. IN connectors
are not output to the TV.
Input
source
DVD
HDP
TV
SAT/CBL
VCR
DVR
V.AUX
Default
setting
1-RCA
None
None
None
None
2-RCA
None
iPod Dock
The control dock for iPod can be assigned to the DVD SAT/CBL VCR
Change the input source to
DVR V.AUX
CD input sources.
which the control dock for
Assign
:
Assign
the
currently selected input source to the Control Dock for
iPod is assigned.
iPod input.
None : Do not assign the currently selected input source to the Control Dock
for iPod input.
•With the default settings, the control dock for iPod can be used
connected to the VCR (iPod) connector.
•Even if “iPod Dock” is set to “Input Assign”, if AVR-2310CI and control
dock for iPod are not connected, the input is used as the normal input
source.
NOTE
Troubleshooting
When “HDMI Control” is set to “ON”, HDMI cannot be assigned to “TV”
at the “HDMI” settings (vpage 31).
Specifications
Input Assign (Digital)
TV
SAT/CBL VCR DVR V.AUX
CD
Digital : The DVD HDP
Assign input sources to input
input sources are assigned to the digital audio input terminals as
SIRIUS
connectors.
shown below.
• Coax1 / Coax2 / Opt1 / Opt2 / Opt3
• None : Do not assign a digital input terminal to the currently selected
input source.
bUpon purchase, the settings of the different input sources are as shown
below.
Input source
DVD
HDP
TV
SAT/CBL
VCR
Coax1
None
Opt1
Coax2
None
Input source
DVR
V.AUX
CD
SIRIUS
Default setting
Opt2
Opt3
None
None
Default setting
37
Remote control
operation buttons
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
ENGLISH
Making the video settings (Video)
Default settings are underlined.
NOTE
•This can also be set by pressing
•To cancel, press
.
to select “Source”.
This can be set when the input source is DVD
VCR DVR V.AUX .
HDP
TV
Remote Control
SAT/CBL
ON : The input video signal is converted.
OFF : The input video signal is not converted.
Information
Video Convert
The input video signal is
converted automatically in
function of the connected
TV (vpage 10 “Converting
Input Video Signals for
Output (Video Conversion
Function)”).
Multi-Zone
Troubleshooting
• When a non-standard video signal from a game machine or some other
source is input, the video conversion function might not operate. In this
case set “Video Convert” to “OFF”.
• When “Video Convert” is set to “OFF”, the video conversion function
does not work. In this case, connect the AVR-2310CI and TV with the
same type of cable.
Remote control
operation buttons
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
Specifications
i/p Scaler
TV SAT/CBL VCR DVR V.AUX
This can be set to the DVD HDP
The input source’s resolution
input sources.
is converted to the resolution
OFF : Do not use i/p scaler function.
set at “Resolution”.
Analog : Analog signals are converted to HDMI signals.
Analog and HDMI : Both analog signals and HDMI signals are converted
to the desired HDMI resolution.
Resolution
This can be set when the input source is set to DVD
HDP
TV
Set the output resolution.
SAT/CBL VCR DVR V.AUX , and when “i/p Scaler” is set to anything
Resolution A (Analog) : Analog
other than “OFF”.
Video
AUTO : Detect monitor panel resolution and automatically set output
Resolution H (HDMI) : HDMI
resolution.
480p/576p / 1080i / 720p / 1080p / 1080p:24Hz : Select the output
resolution.
Playback
• It is not possible to select HDMI input signals.
• When playing HDMI video input signals, the analog video signal of
another input source cannot be selected for the HDMI video output.
• Input sources for which “Delete” is selected at “Source Delete” (vpage
33) cannot be selected.
• Input sources for which “None” is selected at “Input Assign” (vpage
37) cannot be selected.
Settings
Setting items
Setting contents
Video Select
Source : Play the picture and sound of the input source.
Switch video input source DVD / HDP / TV / SAT/CBL / VCR / DVR / V.AUX : Select video input
while listening to audio source to view. This can be set for individual input sources.
signal.
Connections
The items that can be set depend on the input source and the “Input Assign” setting.
Setting items
Setting contents
Progressive Mode
This can be set when the input source is set to DVD
HDP
TV
Select optimum progressive
SAT/CBL VCR DVR V.AUX , and when “i/p Scaler” is set to anything
mode for video material.
other than “OFF”.
AUTO : The video material is automatically detected and the appropriate
mode is set.
Video1 : Select mode suitable for video playback.
Video2 : Select mode suitable for video and 30-frame film material
playback.
Aspect
This can be set when the input source is set to DVD
HDP
TV
Set the aspect ratio of the
SAT/CBL VCR DVR V.AUX , and when “i/p Scaler” is set to anything
video signal output from the
other than “OFF”.
HDMI terminal.
Normal : Output at 4:3 aspect ratio.
Full : Output at 16:9 aspect ratio.
Getting Started
Making the input settings (Input Setup)
: Decision the setting
: Return to previous menu
38
ENGLISH
Getting Started
Making the input settings (Input Setup)
Setting items
Changing the Input Source’s Input Mode and
Decoding mode (Input Mode)
Default settings are underlined.
Decode Mode
Set the input
decoding mode.
Connections
The selectable input modes depend on the input source and “Input Assign” setting
(vpage 37 “Changing the input sources assigned to the input terminals”).
Setting items
Settings
Playback
Multi-Zone
bUpon purchase, the settings of the different input sources are as shown
below.
Input
source
DVD
HDP
TV
SAT/CBL
Remote Control
Default
setting
Auto
HDMI
Digital
Auto
Input
source
DVR
V.AUX
CD
TUNER
Default
setting
Auto
Auto
Analog
Analog
VCR
Analog
Information
Troubleshooting
•The “HDMI” settings are made for input sources for which HDMI
input terminals are assigned at “Input Assign” (vpage 37).
•The “Digital” settings are made for input sources for which digital
input terminals are assigned at “Input Assign” (vpage 37).
•When a digital signal is properly input, the “
” indicator lights on
the display. If the “
” indicator does not light, check the digital
input connector assignment and the connections.
•The surround mode cannot be set if the input mode is set to “EXT.
IN”.
•This can also be set by pressing
.
Each time you press the button, the input mode display will change.
Specifications
Auto
HDMI
EXT. IN
39
Auto : Detect type of digital input signal and decode and play
source’s automatically.
PCM : Decode and play only PCM input signals.
DTS : Decode and play only DTS input signals.
•This can be set for input sources for which “HDMI” or “Digital” is
assigned at “Input Assign” (vpage 37).
•Normally set this to “Auto”.
Setting contents
Input Mode
Auto : Automatically detect input signal and perform playback.
Set the audio input modes for HDMI : Play only signals from HDMI input. (Excluding CD and SIRIUS)
the different input sources. Digital : Play only signals from digital input.
Analog : Play only signals from analog input.
EXT. IN : Play only signals from EXT. IN input.
Remote control
operation buttons
Displaying the menu
: Cancel the menu
Setting contents
Changing the Input Source’s Display Name (Rename)
Default settings are underlined.
Use this procedure to change the display name of the currently selected input source.
Setting items
Setting contents
Rename
1.Use o p to set the cursor to the character you want to change.
Change the input source’s 2.Use ui to change the character, then press
.
display name to the desired
• Up to 8 characters can be input.
name.
• The input character type can be switched by pressing
while the
display name is being changed.
• The types of characters that can be input are as shown below.
GUpper case charactersH ABCDEFGHIJKLMNOPQRSTUVWXYZ
GLower case charactersH abcdefghijklmnopqrstuvwxyz
GSymbolsH ! “ # $ % & ‘ ( ) * + , - . / : ; < = > ? @ [ \ ] ^ _ ` { | } ˜
GNumbersH 0123456789 (Space)
Default
Yes : Reset to the defaults.
The changed display names No : Do not reset to the defaults.
are reset to the defaults.
Digital
Analog
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
ENGLISH
Correcting the Input Source’s Playback Level
(Source Level)
Setting the Preset Channels to be Skipped (Preset Skip)
Default settings are underlined.
Default settings are underlined.
Setting contents
Setting contents
Preset Skip
This can be set when the source is set to TUNER SIRIUS .
Set the preset memories that
A ~ G : Select the preset channel(s) you do not want to display.
you do not want to display
• ON : Display this number.
when tuning.
• Skip : Skip this number.
Default settings are underlined.
Setting the iPod Playback Mode (iPod Playback Mode)
This can be selected for input sources for which “Input Assign” is assigned at the “iPod Dock”
(vpage 37) setting.
Setting items
Setting items
Setting contents
•Up to 8 characters can be input.
Default settings are underlined.
4.Repeat steps 2 and 3 to change the display name.
Default
Yes : Reset to the defaults.
The changed display names No : Do not reset to the defaults.
are reset to the defaults.
Specifications
Presetting Radio Stations (Auto Preset)
GUpper case charactersH ABCDEFGHIJKLMNOPQRSTUVWXYZ
GLower case charactersH abcdefghijklmnopqrstuvwxyz
GSymbolsH ! “ # $ % & ‘ ( ) * + , - . / : ; < = > ? @ [ \ ] ^ _ ` { | } ˜
GNumbersH 0123456789 (Space)
Setting contents
Auto Preset
This can be set when the source is set to TUNER .
Use the auto preset function
Start : Start the auto preset process.
to program radio stations.
If an FM station cannot be preset automatically, select the desired station
by tuning it in manually, then preset it manually.
Remote control
operation buttons
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
Troubleshooting
•The input character type can be switched by pressing
while the
display name is being changed.
•The types of characters that can be input are as shown below.
Shuffle
nWhen DENON control dock for iPod ASD-1R or ASD-11R is
Make settings for shuffle
connected
mode.
Songs : Shuffle all songs.
Albums : Shuffle songs from current album only.
OFF : Cancel shuffle mode.
Information
2.Use o p to set the cursor to the character you want to change.
3.Use ui to change the character, then press
.
Repeat
All : Repeat all songs.
Make settings for repeat One : Repeat the current song.
mode.
OFF : Cancel repeat mode.
Setting items
Setting contents
Preset Name
This can be set when the source is set to TUNER .
Assign name to a preset
1.Use ui to select the preset channel name you want to change,
memory.
then press
.
Remote Control
Default settings are underlined.
Multi-Zone
Assign Name to a Preset Memory (Preset Name)
Playback
If you set “Block Presets” to “Skip”, you can skip the preset memory
blocks (A to G).
Settings
Setting items
Source Level (Analog)
–12dB ~ +12dB (0dB)
Correct the playback level of
the analog audio input.
Source Level (Digital)
–12dB ~ +12dB (0dB)
Correct the playback level of
the digital audio input.
Setting items
Connections
Use this procedure to correct the playback level of the currently selected input source's audio input.
Set this if there are differences in the input volume levels between the different sources. The analog
input level and digital input level can be corrected separately.
Getting Started
Making the input settings (Input Setup)
40
ENGLISH
Getting Started
Making the input settings (Input Setup)
Setting Radio Reception Restrictions (Parental Lock)
Default settings are underlined.
Check the SIRIUS Radio Reception Sensitivity
(Antenna Aiming)
Default settings are underlined.
Connections
Setting items
Lock Setting
Set the channel
reception limits.
Setting contents
Settings
This can be set when the source is set to SIRIUS .
radio
1. Press
.
2. Using uio p, input the password (4 digits number) and press
.
3. Select channel by pressing ui, and set the lock by pressing o p.
• Unlock : Do not lock selected channel(s).
• Lock : Lock selected channel(s).
Multi-Zone
• The default password is “0000”.
• If the password is wrong, “Incorrect Code” is displayed. Input the correct
password.
• While listening to the channel being played, you can also set parental lock
(vpage 45).
Remote Control
Playback
bWhen a Parental Locked channel is tuned, “Code : [
then input the password.
Edit Lock Code
Change the password.
Setting items
Antenna Aiming
Check the SIRIUS
reception sensitivity.
Setting contents
radio
This can be set when the source is set to SIRIUS .
Satellite : Indicate satellite signal strength.
Terrestrial : Indicate terrestrial signal strength.
SIRIUS Antenna
Display
]” is displayed,
Condition
Signal strength is excellent
Signal strength is good
Signal strength is weak
No signal
This can be set when the source is set to SIRIUS .
1. Press
.
2.Input “Current Lock Code” (4 digits) using uio p, and press
3. Input “New Lock Code” (4 digits) using uio p, and press
.
.
Information
4.Input “Repeat New Lock Code” (4 digits) again using uio p, and
press
.
Troubleshooting
5.Press ui to select “Execute”, and then press
.
If the correct password is input, “Completed” is displayed, and the new
password is modified.
Specifications
• If the “Current Code” is incorrectly input, “Incorrect Code” is displayed,
and proceed again from step 1.
• If the password input is 3 digits or less, “Enter 4-digit” is displayed, and
input again with a 4 digit password.
• If the new password is not correctly input, “Code don’t Match” is displayed
and the password does not change.
• The password cannot be cleared even if the operation to reset the unit is
performed. We recommend writing down the password so as not to forget
it.
41
Remote control
operation buttons
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
ENGLISH
Playing Components
n Operation Flow
Before starting playback, make the connections between the
different components and the settings on the receiver.
Playing Components (vpage 42)
q Standard Playback (vpage 46)
e Direct Playback (vpage 47)
r Stereo Playback (vpage 48)
5
Use
Also refer to the operating instructions of the connected
components when playing them.
● External devices can be controlled by remote control unit
(vpage 57 “Operating the Connected Devices by Remote
Control Unit”).
●
2
3
to “MAIN”.
TurnontheAVR-2310CI’spower.
(vpage 20“Turning the Power On”)
Press toselecttheinputsourceassignedinstep1wabove.
Front
GVariable rangeH
–––
–80.5dB ~ 18.0dB
level setting.
6 Selectthedesiredsurroundmode.
7 Adjustthedesiredsoundfieldeffects.
OKtodisconnect.
(iPod screen)
b If the screens above are not displayed, the iPod may not be
properly connected. Try connecting again.
Specifications
NOTE
eSet
toadjustthevolume.
※The variable range differs according to the input signal and channel
Adjusting the Sound and Picture Quality
(Audio/Video Adjust) (vpage 48)
(vpage 37).
to “MAIN/TV”
Troubleshooting
t Playing the Pure Direct mode (vpage 48)
for iPod.
w Assign the control dock for iPod’s input
(vpage 20“Turning the Power On”)
Make the necessary settings on the
player (language setting, subtitles
setting,etc.)beforehand.
Front
q Set the iPod in the DENON control dock
TurnontheAVR-2310CI’spower.
and select the input
3 Press
source.
the component connected to
4 Play
theAVR-2310CI.
1 Prepareforplayback.
Information
w Playing in a DENON original surround mode
(vpage 47)
2
Listening to music on an iPod®
Remote Control
Selecting the Surround Mode (vpage 46)
①Turn on the power of the TV, subwoofer and player.
②Set the TV’s input to the AVR-2310CI.
Front
③Load the disc in the player.
Multi-Zone
n Operations During Playback (vpage 46)
1Prepareforplayback.
The music / video on an iPod can be played by using the control
dock for iPod (ASD-1R, ASD-11R, ASD-3N or ASD-3W sold
separately).
Connect the control dock for iPod beforehand.(vpage 15 “iPod®”).
Playback
(vpage 44)
The following describes the procedure for playing Blu-ray disc/
DVD players.
Use the same procedure to play other components.
Settings
n Playing Blu-ray Disc/DVD Players (vpage 42)
n iPod® Playback (vpage 42)
n Listening to FM/AM Broadcasts (vpage 43)
n Listening to SIRIUS Satellite Radio Programs
iPod® Playback
Playing Blu-ray Disc / DVD Players
Connections
Getting Started
Playback
(vpage 46“Selecting the Surround Mode”)
(vpage 48“Adjusting the Sound and Picture Quality”)
See overleaf
2
ENGLISH
Getting Started
Playing Components
4
Press
and hold it down for a 2 seconds or more to
select the display mode.
Connections
There are two modes for display the contents recorded on the
iPod.
Browse mode :Displayed on the TV screen.
Settings
Playback
Multi-Zone
Browse mode
Remote mode
Audio file
S
S
Picture file
A
Sz2
Video file
Sz1
Sz2
Remote control
unit (AVR-2310CI)
S
S
iPod®
A
S
Playable
files
Active
buttons
Remote Control
z1:When using an ASD-11R, ASD-3N or ASD-3W control dock for
iPod.
z2:Video may not be output, depending on the combination of
ASD-1R or ASD-11R and iPod.
Front
Use ui to select the menu, then
5 press
or p to select the music or
Information
video file to be played.
Troubleshooting
6 Press
7 Use
or p.
Playback starts.
to adjust the volume.
GVariable rangeH – – –
–80.5dB ~ 18.0dB
※The variable range differs according to the input signal and channel
Specifications
level setting.
8
9 Adjust the desired sound field effects.
Select the desired surround mode.
(vpage 46 “Selecting the Surround Mode”)
(vpage 48 “Adjusting the Sound and Picture Quality”)
43
During playback, either press and hold
Viewing Still Pictures or Videos on the iPod®
or press
nStopping playback temporarily
.
Front
During playback, press
or
.
Press again to resume playback.
nTo cue to the beginning of a track
Remote mode :Displayed on the iPod’s screen.
Display mode
nTo stop
1
During playback,
either press (to cue to
the current track) or
(to cue to the next
track).
nRepeat playback and shuffle
“iPod Playback Mode” (vpage 40)
• Use the RESTORER mode to expand the low and high frequency
components of compressed audio files and achieve a richer sound.
The default setting is “Mode3” (vpage 52).
• To check the name of the title, the artist or the
album when playing in browse mode, press
.
• Press
and set the AVR-2310CI’s power to
the standby mode before disconnecting the
iPod. Also switch the input source to one to
which the menu “iPod dock” is not assigned
before disconnecting the iPod.
Press and hold
mode.
to set the Remote
Front
“Remote iPod” is displayed on the AVR2310CI’s display.
the iPod’s screen, use ui
2 Watching
to select “Photos” or “Videos”.
Press
until the image you want to
3 view
is displayed.
playback
• The time (default : 30 sec) for which the onscreen display are displayed can be set at
menu “GUI-iPod” (vpage 34). Press uio
p to return to the original screen.
• Photo and video data on the iPod can be viewed on the monitor. Only
for iPod equipped with slideshow or video functions. (When using an
ASD-1R or ASD-11R)
• Video may not be output, depending on the combination of ASD-1R
or ASD-11R and iPod.
Front
“TV Out” at the iPod’s “Slideshow Settings” or “Video Settings” must
be set to “On” in order to display the iPod’s photo data or videos on
the monitor. For details, see the iPod’s operating instructions.
iPod is a trademark of Apple Inc., registered in the U.S. and other
countries. The iPod may only be used to copy or play contents that
are not copyrighted or contents for which copying or playback is
legally permitted for your private use as an individual. Be sure to
comply with applicable copyright legislation.
Front
NOTE
• Depending on the type of iPod and the software version, some
functions may not operate.
• DENON will accept no responsibility whatsoever for any loss of iPod
data.
Listening to FM/AM Broadcasts
Basic Operation
1
Set
2
Press
to “MAIN/TV” and
to “MAIN”.
to select “TUNER”.
Front
Front
ENGLISH
to select “FM” or “AM”.
Tune
Rear
in the desired broadcast
station.
qTo tune in automatically (Auto Tuning)
Press
to light the “AUTO” indicator on the display, then use
wTo tune in manually (Manual Tuning)
Press
to turn off the display’s “AUTO” indicator, then use
Presetting Radio Stations (Preset Memory)
Tune in the broadcast station you want to preset.
Front
Press
.
Press
to select the block (A to G)
Press
Press
to select the preset number (1 to 8).
again to complete the setting.
•To preset other stations, repeat steps 1 to 5.
•Stations can be preset automatically at menu “Auto Preset” (vpage
40).
to select the desired preset channel (1
to 8).
To subscribe to SIRIUS, U.S. and Canadian customers can call 1-888539-SIRI (1-888-539-7474) or visit sirius.com (US) or siriuscanada.ca
(Canada).
SIRIUS XM Radio Legal
nDefault settings
Auto tuner presets
A1 ~ A8
87.5 / 89.1 / 98.1 / 107.9 / 90.1 / 90.1 / 90.1 /
90.1 MHz
B1 ~ B8
520 / 600 / 1000 / 1400 / 1500 / 1710 kHz,
90.1 / 90.1 MHz
C1 ~ C8
90.1 MHz
D1 ~ D8
90.1 MHz
E1 ~ E8
90.1 MHz
F1 ~ F8
90.1 MHz
G1 ~ G8
90.1 MHz
Listening to
Programs
SIRIUS, XM and all related marks and logos are trademarks of Sirius
XM Radio Inc. and its subsidiaries. All other marks and logos are the
property of their respective owners. All rights reserved. SIRIUS and
XM subscriptions sold separately. Taxes and a one-time activation fee
may apply. XM tuners and home docks or SIRIUS tuners (each sold
separately) are required to receive the SIRIUS or XM satellite radio
service. All programming and fees subject to change. It is prohibited to
copy, decompile, disassemble, reverse engineer, hack, manipulate or
otherwise make available any technology or software incorporated in
receivers compatible with the SIRIUS or XM Satellite Radio Systems.
Service not available in Alaska and Hawaii.
Basic Operation
SIRIUS
Satellite
Radio
About SIRIUS XM Radio
To listen to Satellite Radio, you’ll need to connect either a SIRIUS or XM
Satellite Radio tuner (sold separately) to your satellite-ready receiver.
Satellite Radio is available to residents of the US (except Alaska and
Hawaii) and Canada.
Satellite Radio delivers a variety of commercial-free music from
categories ranging from Pop, Rock, Country, R&B, Dance, Jazz,
Classical and many more plus coverage of all the top professional
and college sports including play by play games from select leagues
and teams. Additional programming includes expert sports talk,
uncensored entertainment, comedy, family programming, local traffic
and weather and news from your most trusted sources.
Whether you purchase a SIRIUS or XM tuner, you’ll need to activate
and subscribe to begin enjoying the service. Easy to follow installation
and setup instructions are provided with the satellite tuners. Whichever
service you choose, there are a variety of programming packages
available, including the option of adding “The Best of SIRIUS”
programming to your XM tuner or “The Best of XM” programming
to your SIRIUS tuner, enabling you to enjoy the most popular
programming among both services. The “Best of” packages are not
available to SIRIUS or XM Canada subscribers at this time.
1
Set
2
Press
3
Use
to “MAIN/TV” and
to “MAIN”.
to select “SIRIUS”.
Front
Front
to select the channel.
When the channel is tuned in, the name of
the track and artist are displayed.
Specifications
in which the station is to be preset.
Press
Troubleshooting
1
2
3
4
5
to select the memory block (A to G).
Information
Your favorite broadcast stations can be preset so that you can tune
them in easily. Up to 56 stations can be preset.
Remote Control
•When tuning in stations manually, press and hold
to change
frequencies continuously.
•The time (default : 30 sec) for which the GUI menu are displayed can
be set at “GUI-Tuner” (vpage 34).
Press
Multi-Zone
•If the desired station cannot be tuned in with auto tuning, tune it in
manually.
1
2
To subscribe to XM, U.S. customers should visit xmradio.com or call
1-800-XMRADIO (1-800-967-2346); Canadian customers should visit
xmradio.ca or call XM Listener Care at 1-877-GETXMSR (1-877-4389677).
Playback
to select the station you want to hear.
Listening to Preset Stations
Settings
to select the station you want to hear.
NOTE
Preset stations are erased by overwriting them.
Connections
3
4
Press
Getting Started
Playing Components
Family friendly packages are also available to restrict channels featuring
content that may be inappropriate for children.
See overleaf
44
ENGLISH
Getting Started
Playing Components
Searching Categories
Front
•The channel switches continuously when
The strength of both the SIRIUS and terrestrial signals can be checked
at menu “Antenna Aiming” (vpage 41).
is pressed and held.
Connections
Your favorite broadcast channels can be preset so that you can tune
them in easily. Up to 56 channels can be preset.
Settings
Playback
Checking the SIRIUS Signal Strength and Radio ID
Multi-Zone
1
2
to select “SIRIUS”.
Front
Press
Remote Control
Information
Troubleshooting
Specifications
3
4
5
on the main unit until “SIGNAL” appears
on the display.
The display will switch as shown below,
depending on the reception conditions.
1
2
3
Press
.
Front
to select the block (A
to G) in which the channel is to be
preset.
4
5
Status
Signal strength is excellent
Signal strength is good
Signal strength is weak
No signal
2
Channel category
o p to select the category,
then use ui to select the desired
Use
Front
channel.
Press
Press
•“UPDATING” is displayed while the encoding code is being
updated.
•“SIRIUS UPDATING” is displayed when updating SIRIUS tuner
firmware.
•Refer to “Troubleshooting” – “SIRIUS Satellite Radio” regarding other
messages (vpage 69).
Parental Lock
to select the preset number (1 to 8).
again to complete the setting.
1
2
3 uio p
Tune to the channel you want to lock.
Press
“Code: [
for at least 3 seconds.
Front
]” is displayed.
Enter the 4-digit lock code using
.
Adjust the position of the antenna until “SIGNAL:
EXCELLENT” is shown on the display.
on the main unit until the channel you
want to check (example: “SR001”) is displayed.
Press
and select channel 0 (SR000).
Front
Channel No. and Sirius ID are alternately
shown on the display.
SR000 SiriusID
************
Sirius ID
bWrite your own SIRIUS ID for storage use.
Sirius ID :
To preset other channels, repeat steps 1 to 5.
NOTE
Press
45
SR001 Hits 1
CAT : Pops
Tune in the broadcast channel you want to preset.
Press
Display
EXCELLENT
GOOD
WEAK
NO SIGNAL
Press o p.
Presetting Radio Channels (Preset Memory)
•The song title, artist name, composer name,
category and reception level can be checked
by pressing
on the main unit.
•The time (default : 30 sec) for which the onscreen display are displayed can be set at
menu “GUI-Tuner” (vpage 34).
Press uio p to return to the original screen.
Press
1
Preset channels are erased by overwriting them.
Listening to Preset Channels
1
2
Press
Press
to 8).
When you enter the correct code, the corresponding channel is
locked.
4
Press
.
to select the memory block (A to G).
to select the desired preset channel (1
•Channels under Parental Lock cannot be tuned in by performing
Tuning Up/Down or by category search.
•Channels stored in preset memory can be tuned in by the preset
channel select operation, even if Parental Lock is applied.
•When a channel to which Parental Lock is applied is being played,
Parental Lock for that channel is cancelled by performing Step2.
•See “Edit Lock Code” (vpage 41) for the method of changing
Parental Lock Code.
•You can also set “Parental Lock” from the menu (vpage 41).
ENGLISH
Operations During Playback
Selecting the Surround Mode
Getting Started
Playing Components
Select a surround mode to enjoy surround playback with your favorite sound field effects.
Turning Off the Sound Temporarily (Muting)
Front
.
q Playing Sources According to the Sources’ Audio Signal Format/Number of
Channels (Standard Playback)
Operations
The sound from the speakers and pre-out connectors is automatically
cut.
Press
mode.
to select the surround
Rear
Select the mode for the source at “Mode” (vpage
48).
nDOLBY PLgx, DOLBY PLg
Cinema
:This mode is suited for movie sources.
Music
:This mode is suited for music sources.
Game
:This mode is suited for games.
Pro Logic :This is the Pro Logic playback mode. This can be
NOTE
.
Front B
Front A+B
NOTE
DOLBY PLgx,
DOLBY PLg
or
DOLBY PLgz
DTS NEO:6
Cinema
:This mode is suited for movie sources.
Music
:This mode is suited for music sources.
z
:The signals are decoded in DOLBY PLgx,
DOLBY PLg or DOLBY PLgz, for playback.
:The signals are decoded in DTS NEO:6 for
playback.
※The modes that can be selected depend on the input source
being played.
he “Cinema” and “Music” modes can also be set by pressing
T
or
.
z:DOLBY PLgx can be selected when surround back speakers are
being used.
Specifications
When you set to “Custom” with “Front Speaker Setup“ (vpage 30),
you cannot operate
.
When you select “DOLBY PLgz”, set “Amp
Assign” to “Front Height”.
nDTS NEO:6
Troubleshooting
Front A
n2channel sources
Information
Switching the front speakers
The surround modes that can be selected
differ according to the input source.
Remote Control
selected when playing with a DOLBY PLg decoder.
When this mode is selected, “DOLBY PL” is
displayed.
nMultichannel sources
• To prevent hearing loss, do not raise the volume level excessively
when using headphones.
• Unplug headphones when performing the Audyssey Auto Setup
procedure or other settings.
Press
1
2
This is the operation for playing 2-channel sources.
Multi-Zone
Plug the headphones into the PHONES jack on the main
unit.
Playing the source (vpage 42).
Playback
Listening with Headphones
3
Settings
• The sound is reduced to the level set at menu “Mute Level” (vpage
33).
• To cancel, press
again. Muting can also be canceled by adjusting
the master volume.
The selectable surround modes depend on the following:
•Format of the audio signals being input
•Number of channels of the audio signals being input
•The set amplifier assignment mode (vpage 28)
Connections
Press
See overleaf
46
ENGLISH
Getting Started
Selecting the Surround Mode
Displaying the currently playing surround mode
nSurround playback of multichannel sources
(Dolby Digital, DTS, etc.)
Connections
In the case of standard playback of multi channel sources, the
AVR-2310CI recognizes the format of the multi-channel audio
input signal and automatically operates the appropriate decoder
for surround sound.
Settings
Input signal
Playback
Dolby Digital
(other than 2ch)/
Dolby Digital EX
Multi-Zone
Dolby
Digital
Dolby Digital Plus
(z1)
Remote Control
Dolby TrueHD (z1)
Information
DTS (5.1ch)/
DTS-ES Discrete 6.1 /
DTS-ES Matrix 6.1 /
DTS 96/24
DTS
Troubleshooting
DTS-HD (z1)
Specifications
PCM
PCM
(multi ch)
The indication contents of
the display
DOLBY DIGITAL
DOLBY DIGITAL EX
DOLBY DIGITAL+PLgx CINEMA
DOLBY DIGITAL+PLgx MUSIC
DOLBY DIGITAL+PLgz
DOLBY DIGITAL+
DOLBY DIGITAL++EX
DOLBY DIGITAL++PLgx C
DOLBY DIGITAL++PLgx M
DOLBY DIGITAL++PLgz
DOLBY TrueHD
DOLBY HD+EX
DOLBY HD+PLgx CINEMA
DOLBY HD+PLgx MUSIC
DOLBY HD+PLgz
DTS SURROUND
DTS+PLgx CINEMA
DTS+PLgx MUSIC
DTS+PLgz
DTS+NEO:6
DTS ES MTRX6.1 (z2)
DTS ES DSCRT6.1 (z3)
DTS 96/24 (z4)
DTS-HD HI RES
DTS-HD MSTR
DTS-HD+NEO:6
DTS-HD+PLgx CINEMA
DTS-HD+PLgx MUSIC
DTS-HD+PLgz
MULTI CH IN
MULTI IN+PLgx CINEMA
MULTI IN+PLgx MUSIC
MULTI IN+PLgz
MULTI CH IN 7.1
z1:When a signal is input, the HD AUDIO indicator lights.
z2:This is displayed when the input signal is “DTS-ES Matrix 6.1”
and the AVR-2310CI’s “AFDM” setting (vpage 49) is set to
“ON”.
z3:This is displayed when the input signal is “DTS-ES Discrete
6.1”.
z4:This is displayed when the input signal is “DTS 96/24”.
47
NOTE
w Playing in a DENON Original
Surround Mode
When the input signal is DOLBY TrueHD, DOLBY DIGITAL Plus,DTSHD
you cannot select DENON original surround mode.
The desired mode according to the program source and viewing
situation can be selected from among 7 DENON original surround
modes.
1
Select the input source by pressing
and play the source (vpage
42).
Front
Press
mode.
2
to select the Surround
Rear
5CH/7CH STEREO :This mode is for enjoying stereo sound from all
speakers.
ROCK ARENA
:This mode is for enjoying the atmosphere of a
live concert in an arena.
JAZZ CLUB
:This mode is for enjoying the atmosphere of a
live concert in a jazz club.
MONO MOVIE :This mode is for playing monaural movie
sources with surround sound. z1
VIDEO GAME
:This mode is suited for achieving surround
sound with video games.
MATRIX
:This mode lets you add a sense of expansion
to stereo music sources.
VIRTUAL
:This mode is for enjoying surround effects
using only the front speakers or headphones.
z1:When playing sources recorded in monaural in the MONO
MOVIE mode, the sound will be off balance with a single
channel (left or right), so input to both channels.
Depending on the program source being played, it may not be possible
to achieve a satisfactory surround effect. In this case, try other modes
to achieve a sound field suited to your tastes.
e Direct Playback
In this mode the signals bypass the tone adjustment circuitry for
high quality sound.
The sound is output to the same channels as the input signal.
1
Select the input source by pressing
and play the source (vpage
42).
2
Press
to select the “DIRECT”.
Front
Rear
Displaying the currently playing surround mode
Input signal
Analog signal /
PCM (2ch) /
Dolby Digital source /
DTS source /
Other 2-channel digital signals
PCM (multi ch)
The indication contents of
the display
DIRECT
MULTI CH DIRECT
M DIRECT + PLgx CINEMA
M DIRECT + PLgx MUSIC
M DIRECT + PLgz
M DIRECT 7.1
ENGLISH
Selecting the Surround Mode
r Stereo Playback
input source by pressing
1 Select the
andplaythesource(vpage
Front
The sound being played in the surround mode can be adjusted to your liking.
The items (parameters) that can be adjusted depend on the signal being input and the currently set surround
mode. For details on the adjustable parameters, see “Surround Modes and Parameters” (vpage 62).
NOTE
Rear
toselectthe“STEREO”.
Some of the setting items cannot be set while playback is stopped. Set these items during playback.
Setting items
Mode
t Playing the Pure Direct Mode
1
2
Press
.
n In the DTS NEO:6 mode
Cinema : This is the mode for cinema source.
Music : This is the mode for music source.
Front
Rear
See overleaf
Remote control
operation buttons
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
Specifications
NOTE
When in the PURE DIRECT mode, the GUI menu is not displayed
and the display on the main unit is turned off.
Troubleshooting
• To cancel, press
again.
• The channel level and surround parameters in the PURE DIRECT
mode are the same as in the DIRECT mode.
• The “Music” mode is also effective for movie sources including a
lot of stereo music.
• The “Cinema” and “Music” modes can also be set by pressing
or
.
OFF
:
“Cinema
EQ”
is not used.
Cinema EQ
Soften the treble range of ON : “Cinema EQ” is used.
movie sound tracks for better
understanding.
Dynamic
Range Low/Mid/High : These set the compression level.
Compression (D.Comp) OFF : Turn dynamic range compression off.
Compress dynamic range
The “D.Comp” indicator lights when playing DTS source that supports
(difference between loud
the “D.Comp” function.
and soft sounds).
Dynamic Range Control Auto : Dynamic range compression of Dolby TrueHD sources turns on and
off automatically.
(DRC)
Low/Mid/High : These set the compression level.
Compress dynamic range
OFF : Turn dynamic range compression off.
Information
Select the input source by pressing
andplaythesource(vpage
42).
Cinema : This is the mode for cinema source.
Music : This is the mode for music source.
Game : This is the mode for game source.
ProLogic : Dolby Pro Logic playback mode (PLg mode only). (This is
the mode for 4-channel playback (front L, front R, center, surround
(MONO).)
Remote Control
This is the mode that recreates the original sound most faithfully,
providing extremely high quality sound.
n In the PLgx, PLg or PLgz mode
Multi-Zone
Set the play mode for
playing 2-channel sources in
surround.
Setting contents
Playback
2
Press
Default settings are underlined.
Settings
42).
Adjusting the Sound (Audio Adjust)
Connections
This is the mode for playing in stereo. The tone can be adjusted.
Sound is output from the front left and right speakers and
subwoofer.
Getting Started
Adjusting the Sound and Picture Quality
(Audio/Video Adjust)
ENGLISH
Getting Started
Adjusting the Sound and Picture Quality (Audio/Video Adjust)
Setting items
LFE
Setting contents
Setting items
–10dB ~ 0dB
Connections
Adjust the low-frequency
effects level (LFE).
Settings
Center Image
For proper playback of the different program sources, we recommend
setting to the values below.
•Dolby Digital sources : “0dB”
•DTS movie sources :
“0dB”
•DTS music sources :
“–10dB”
0.0 ~ 1.0 (0.3)
Assign center channel signal
to front left and right channels
for wider sound.
Setting contents
AFDM (Auto Flag Detect ON : Set.
OFF : Do not set.
Mode)
Detects the source’s surround
back channel signal and sets
the optimum surround mode
automatically.
Surround Back
Sets the method of
generating of the surround
back channel.
Playback
Panorama
Multi-Zone
Remote Control
Information
Troubleshooting
Specifications
ON : Set.
Assign front L/R signal also OFF : Do not set.
to surround channels, for
wider sound.
0 ~ 6 (3)
Dimension
Shift sound image center
to front or rear, to adjust
playback balance.
0 ~ 7 (3)
Center Width
Assign center channel signal
to front left and right channels
for wider sound.
0ms ~ 300ms (30ms)
Delay Time
Adjust delay time to control
sound stage size.
1 ~ 15 (10)
Effect Level
Adjust the strength of the
Set to a lower level if the positioning and sense of phase of the
surround effect.
surround signals seems unnatural.
Small : Simulate acoustics of a small room.
Room Size
Determine size of acoustic Medium small : Simulate acoustics of a medium-small room.
Medium : Simulate acoustics of a medium room.
environment.
Medium large : Simulate acoustics of a medium-large room.
NOTE
Large : Simulate acoustics of a large room.
“Room Size” does not
indicate the size of the room
in which sources are played.
nFor 2-channel sources
ON : The surround back channel is used.
OFF : No signal is played from the surround back channels.
nFor multi channel sources
Set this to set the method of generating of the surround back channel
for sources that do not include surround back signals and when you
do not want to play the surround back signals included in the source.
Check the audio signals of the source being played before making this
setting.
OFF : No signal is played from the surround back channels.
MTRX ON : Generate and play the surround back signals from the
surround channel signals.
PLgx CINEMAz1 : Generate and play the surround back signals by
decoding the signals in the “Dolby Pro Logic gx Cinema” mode.
PLgx MUSICz2 : Generate and play the surround back signals by
decoding the signals in the “Dolby Pro Logic gx Music” mode.
ES MTRX : Generate and play the surround back signals from the
surround channel signals of the DTS source.
ES DSCRTz3 : Play the surround back signals included in the 6.1channel DTS source.
DSCRT ONz3 : Play the surround back signals included in the 7.1channel source.
z1 : This can be selected when “S.Back” in the “Speaker Config.”
settings (vpage 29) is set to “2sp”.
z2 : This can be selected when “S.Back” in the “Speaker Config.”
settings (vpage 29) is set to “2sp” or “1sp”.
z3 : When “AFDM” is set to “ON”, the surround back channel is played
with the AFDM function. When selected while “AFDM” is set to
“OFF”, the source’s surround back signals are played.
This can also be set by pressing
.
NOTE
This is valid when the “Amp Assign” setting (vpage 28) is set to “7.1channel surround back” or “6.1-channel surround back”, and when the
“S.Back” setting (vpage 29) is set to “Large” or “Small”.
See overleaf
49
Remote control
operation buttons
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
ENGLISH
Setting items
Making the MultEQ, Dynamic EQ and Dynamic Volume
Settings (Audyssey Settings)
Setting contents
Front Height
Default settings are underlined.
Subwoofer ATT
ON : The input from the subwoofer channel is attenuated.
Attenuate subwoofer level OFF : The input from the subwoofer channel is not attenuated. Usually use
in this mode.
when using EXT. IN mode.
Setting contents
Bass
–6dB ~ +6dB (0dB)
Adjusts the low frequencies.
Treble
–6dB ~ +6dB (0dB)
Adjusts
the
frequencies.
high
This can be set when
“Tone Control” is set to
“ON”.
Remote control
operation buttons
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
50
Specifications
This can be set when
“Tone Control” is set to
“ON”.
Troubleshooting
ON : Allow tone adjustment (treble, bass).
Sets the tone control function OFF : Playback without tone adjustment.
ON and OFF.
The tone cannot be adjusted when in the DIRECT mode.
This can be set when
“Dynamic EQ” (vpage
51) is set to “OFF”.
Information
Tone Control
Setting contents
Audyssey : Optimize frequency response of all speakers.
Corrects
the
frequency Audyssey Byp.L/R : Optimize frequency response of speakers except
response of the different front L and R speakers.
Audyssey Flat : Optimize frequency response of all speakers to flat
speakers.
response.
NOTE
Manual : Apply frequency response set with “Manual EQ” (vpage 51).
•“MultEQ” and “Manual OFF : The “MultEQ” equalizer cannot be used.
EQ” settings for which
• When “Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is
“Not Used” has been set at
selected, “
” lights.
“EQ Customize” (vpage
32) cannot be selected.
• After running Audyssey Auto Setup, if the Speaker Configuration,
•When using headphones,
Distance, Channel Level, and Crossover Frequency have changed
“MultEQ” is set to “OFF”.
without increasing the number of speakers measured, only “
”
lights.
•This can also be set by pressing
.
Remote Control
Setting items
Setting items
MultEQ
Multi-Zone
Default settings are underlined.
Playback
Adjusting the Tone (Tone Control)
NOTE
If the speaker settings are changed after the “Audyssey Auto Setup” procedure is performed,
“MultEQ”, “Dynamic EQ” and “Dynamic Volume” functions cannot be selected and “Run Audyssey”
is displayed.
If this happens, either perform the “Audyssey Auto Setup” procedure again, or perform the “Restore”
operation (vpage 27) to restore the settings to as they were after the “Audyssey Auto Setup”
procedure was performed.
Settings
Set this to “ON” if the subwoofer channel level seems too high when
playing audio signal.
ON : The subwoofer is used.
Subwoofer
Turn subwoofer output on OFF : The subwoofer is not used.
and off.
Yes : Reset to the defaults.
Default
Restores all the surround No : Do not reset to the defaults.
parameter settings to their
defaults.
•When the “Audyssey Auto Setup” (vpage 23) procedure is performed, the “MultEQ”, “Dynamic
EQ” and “Dynamic Volume” functions are enabled.
•Operating conditions for each function
•Dynamic EQ :
MultEQ
When “MultEQ” is set to “ON”
Dynamic EQ
•Dynamic Volume :
When “Dynamic EQ” is set to “ON”
Dynamic Volume
•Setting :
Setting
When “Dynamic Volume” is set to “ON”
Connections
ON : Use the front height channel.
Set whether or not to use OFF : Do not use the front height channel.
the front height channel.
This can also be set by pressing
.
Getting Started
Adjusting the Sound and Picture Quality (Audio/Video Adjust)
ENGLISH
Getting Started
Adjusting the Sound and Picture Quality (Audio/Video Adjust)
Setting items
Setting contents
Setting items
Dynamic EQ
Connections
ON : Use Dynamic EQ function.
Audyssey Dynamic EQ solves OFF : Do not use Dynamic EQ function.
the problem of deteriorating
•W
hen set to “ON”, “
” is displayed.
sound quality as volume is
•
W
hen
“MultEQ”
is
set
to
“OFF”
, “Dynamic EQ” is automatically set
decreased by taking into
to “OFF”
account human perception
•This can also be set by pressing
.
and room acoustics.
Settings
Dynamic EQ : ON/Volume : OFF
Playback
This can be set when the
“MultEQ” (vpage 50)
is set to anything other
than “OFF”.
“Red”
“Green”
Setting
Set Dynamic Volume effect.
This can be set when
“Dynamic EQ” (vpage
51) is set to “ON”.
Setting contents
Day : Low setting provides the least adjustments to the loudest and
softest of sounds.
Evening : Middle setting prevents loud and soft sounds from being much
louder and softer respectively than average sounds.
Midnight : High setting affects volume the most, causing all sounds to be
of equal loudness.
Dynamic EQ / Volume : OFF
Adjust Tonal Quality for Each Speaker Using Graphic
Equalizer (Manual EQ)
“Off”
“OFF”
Default settings are underlined.
NOTE
Multi-Zone
“Tone Control” is set to “OFF” when “Dynamic EQ” is set to “ON”.
Reference Level Offset : Audyssey Dynamic EQ takes the standard film
mixing level of 85 dB SPL during –20 dB FS input as its reference level.
However, since standardization is lacking outside the film industry, the
reference level of media contents may not be appropriate. In order to
view such contents, Reference Level Offset of Dynamic EQ has available
offsets of 5 dB, 10 dB and 15 dB.
• 0dB : Suitable for viewing movies.
• 5dB : Suitable for listening to classical music and other content mixed
at a high level.
• 10dB : Suitable for listening to jazz and other audio sources with a wide
dynamic range. Also suitable for viewing TV.
• 15dB : Suitable for listening to pop, rock music and other content with an
extremely wide dynamic range.
Remote Control
Information
Troubleshooting
Specifications
etting is enabled when “Dynamic EQ” is “ON”.
S
ON : Use Dynamic Volume. The Dynamic Volume effect will be at the level
Audyssey Dynamic Volume of the “Setting” (vpage 51)
solves the problem of OFF : Do not use Dynamic Volume.
large variations in volume
•When set to “ON”, “
” is displayed.
level between television
•When “MultEQ” is set to “OFF”, “Dynamic Volume” is automatically
programs, commercials, and
set to “OFF”.
between the soft and loud
•This can also be set by pressing
.
passages of movies.
Dynamic EQ / Volume : ON
Dynamic EQ : ON / Volume : OFF
Dynamic Volume
This can be set when
“Dynamic EQ” (vpage
51) is set to “ON”.
51
Remote control
operation buttons
“Green”
“Green”
Displaying the menu
: Cancel the menu
Setting items
Setting contents
Adjust CH
1.Select speaker adjustment method.
All CH : Adjust tonal quality for all speakers together.
Adjust the tonal quality of
L/R CH : Adjust tonal quality for each L/R speaker pair.
the individual speakers.
Each CH : Adjust tonal quality for each speaker separately.
2.Select the frequency band to be adjusted.
63Hz / 125Hz / 250Hz / 500Hz / 1kHz / 2kHz / 4kHz / 8kHz /
16kHz
bWhen “L/R CH” or “Each CH” is selected, select the speaker to be
adjusted.
3.Adjust the level.
–20.0dB ~ +6.0dB (0dB)
Yes : Copy.
Base Curve Copy
Copy the MultEQ “Audyssey No : Do not copy.
Flat” correction curve.
“Base Curve Copy” is displayed after the Audyssey Auto Setup
procedure has been performed.
Yes : Reset to the defaults.
Default
Reset the “Manual EQ” No : Do not reset to the defaults.
settings to their defaults.
“Red”
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
ENGLISH
Restoring Compressed Audio to Nearly Pre-compressed
Conditions for Playback (RESTORER)
Adjusting the Picture Quality (Picture Adjust)
Default settings are underlined.
Default settings are underlined.
Mode 1
(RESTORER 64)
Mode 2
(RESTORER 96)
Mode 3
(RESTORER HQ)
–6 ~ +6 (0)
–6 ~ +6 (0)
OFF / Low / Middle / High
Remote Control
OFF
0 ~ +12
Multi-Zone
• The default setting for “iPod” is “Mode3”. All others are set to “OFF”.
• When set to something other than “OFF”, “
” is displayed.
• This can also be set by pressing
during playback.
Setting contents
–6 ~ +6 (0)
Playback
OFF : Do not use RESTORER.
Mode1 (RESTORER 64) : Optimized mode for compressed sources with very weak highs.
Mode2 (RESTORER 96) : Apply suitable bass and treble boost for all compressed sources.
Mode3 (RESTORER HQ) : Optimized mode for compressed sources with normal highs.
Setting items
Contrast
Adjust picture contrast.
Brightness
Adjust picture brightness.
Chroma Level
Adjust picture chroma level
(saturation).
Hue
Adjust color hue.
DNR
Reduce overall picture noise.
Enhancer
Emphasize picture contours.
Settings
Setting contents
TV
SAT/CBL VCR DVR V.AUX .
• This can be set when the input source is DVD HDP
b With input sources other than the ones above, this can be set when “Video Select” is selected. In this
case, the original input source settings are called out.
• Can be set when the “Video Convert” setting (vpage 38) is “ON”.
0 ~ +12
Information
• “DNR” and “Enhancer” are each effective with HDMI output.
• The value set at “Picture Adjust” is stored in the memory individually for each input source.
Adjusting the Audio Delay Time while Watching the
Picture (Audio Delay)
Default settings are underlined.
Troubleshooting
Setting contents
0ms ~ 200ms
• If you wish to adjust the “Audio Delay” while playing HDMI or component video signals, press u
to set “GUI” to “OFF”. This way the audio delay can be adjusted while watching the picture. (Press
the u again. The display switches to the display of the menu screen only.)
• This cannot be adjusted when playing in the EXT. IN, DIRECT or STEREO mode (with “Front
Speaker” set to “Large”, “Tone Control” to “OFF” and “MultEQ” and “RESTORER” to “OFF”).
• When the Auto Lipsync Correction function is operating, you can set within the range 0 ~ 100 ms.
• Store “Audio Delay” for each input source.
Remote control
operation buttons
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
Specifications
Connections
• Such compressed audio formats as MP3, WMA (Windows Media Audio) and MPEG-4 AAC reduce the
amount of data by eliminating signal components that are hard for the human ear to hear. The RESTORER
function generates the signals eliminated upon compression, restoring the sound to conditions near
those of the original sound before compression. It also corrects the sense of volume of the bass to obtain
richer sound with compressed audio signals.
• This can be set with analog signals or when a PCM signal (fs = 44.1/48 kHz) is input.
Getting Started
Adjusting the Sound and Picture Quality (Audio/Video Adjust)
: Decision the setting
: Return to previous menu
2
ENGLISH
Getting Started
Checking the Status
(Information)
Connections
Setting items
Status
Shows information
current settings.
Setting contents
Select Source / Name / Surround Mode / Input Mode / Decode Mode /
about HDMI / Digital / Component / iPod Dock /Video Select /Video Convert /
i/p Scaler / Resolution / Progressive Mode / Aspect
Settings
Playback
Multi-Zone
Remote Control
Information
Troubleshooting
Specifications
You can also display current status on the main unit’s display each time you
press
on the main unit.
ZONE2
• POWER/ Select Source/ Master Volume
Surround Mode : The currently set surround mode is displayed.
Audio Input Signal
Shows information about Signal : The input signal type is displayed.
fs : The input signal’s sampling frequency is displayed.
audio input signals.
Format : The number of channels in the input signal (front, surround, LFE)
is displayed.
Offset : The dialogue normalization correction value is displayed.
Flag : This is displayed when inputting signals including a surround back
channel. “MATRIX” is displayed with Dolby Digital EX and DTS-ES Matrix
signals, “DISCRETE” with DTS-ES Discrete signals.
HDMI Signal Information
HDMI Information
Shows information about • Resolution / Color Space / Pixel Depth
HDMI input signals and HDMI Monitor Information
monitor.
• Interface / Suport Resolution
Analog/PCM / Digital 2ch / Digital 5.1ch / Multi CH
Auto Surround Mode
Shows information about
auto
surround
mode
settings.
Quick Select 1 / Quick Select 2 / Quick Select 3
Quick Select
Shows information about • Select Source / Video Select / MultEQ / Dynamic EQ / Dynamic Vol /
Analog/PCM / Digital 2ch / Digital 5.1ch / Multi CH
quick select settings.
ZONE2 Quick Select
Z2 Quick Select 1 : Select Source / Volume Level
Z2 Quick Select 2 : Select Source / Volume Level
Z3 Quick Select 3 : Select Source / Volume Level
A1~G8
Preset Channel
Shows information about • TUNER / SIRIUS
preset channels.
3
Remote control
operation buttons
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
ENGLISH
HDMI Control Function
power off step
zWhen you set “Output audio from amp” in the TV audio
n You can switch audio output devices with a TV
volume adjustment operation
linkage to TV input switching
n When playing the player, the AVR-2310CI input
function switches to the function of that player
3
4
5
SwitchthetelevisioninputtotheHDMIconnectedto
theAVR-2310CI.
Switch the AVR-2310CI input to the HDMI input
sourceandcheckifthepicturefromtheplayerisok.
WhenyouturntheTV’spowertostandby,checkthat
thepoweroftheAVR-2310CIandplayeralsogoeson
standby.
If the HDMI control function does not operate properly, check the
following points.
• Is the TV or player compatible with the HDMI control function?
• Is the AVR-2310CI properly set?
• Is “HDMI Control” (vpage 31) set to “ON”?
• Is “Power Off Control” (vpage 31) set to “ON”?
• Are the HDMI control function settings of all equipment correct?
Press
anddisplaythetimeyouwanttoset.
The “SLEEP” indicator on the display lights.
• The time switches as shown below each time
pressed.
Sleep:OFF
Sleep:120min
Sleep:30min
is
Sleep:90min
Sleep:60min
• The time display turns off after about 5 seconds, and the
setting is activated.
• Once the set time has passed, the power is automatically set
to standby.
n To cancel the sleep timer
Rear
Press
to set “OFF”.
• The “SLEEP” indicator on the display turns
off.
Troubleshooting
NOTE
NOTE
Should any of the operations below be performed, the interlocking
function may be reset, in which case, repeat step’s 1 and 2.
• Menu “HDMI” (vpage 31) setting has changed.
• There is a change to the connection between the equipment and the
HDMI, or an increase in equipment.
Specifications
• When you power off AVR-2310CI, the HDMI control function does
not operate.
• Some functions may not operate depending on the connected
TV or player. Check the owner’s manual of each device for details
beforehand.
• When “HDMI Control” is set to “ON”, it is not possible to assign an
HDMI terminal to “TV” at “HDMI” (vpage 31).
• When “HDMI Control” (vpage 31) is set to “ON”, power is supplied
constantly to the AC outlet (UNSWITCHED).
Set “HDMI Control” (vpage 31) to “ON“.
b Please refer to the owner’s manual as regards setting of connected
devices.
b Carry out Steps 1 and 2 should any of the equipment be
unplugged.
Information
• To play the TV’s sound on the AVR-2310CI, make optical digital
connections (vpage 14 “Connecting the monitor (TV)”).
• To use this function, set “HDMI Control” (vpage 31) to “ON”.
connectedbyHDMIcable.
This function allows you to automatically set the power to standby
after the set amount of time has passed.
When the sleep timer turns the power off in the MAIN ZONE, the
power also turns off in the ZONE2.
Remote Control
n You can switch AVR-2310CI input source through
Set the HDMI control function for all equipment
Multi-Zone
operation
n You can adjust AVR-2310CI volume in the TV
HDMIcable.
Playback
output setup operation, you can switch the amp power
on.
Turnthepoweronforalltheequipmentconnectedby
Settings
n AVR-2310CI power off can be linked to the TV
1
2
Setting the Power to Standby
After a Certain Amount of Time
(Sleep Timer Function)
Connections
When you make an HDMI connection with a TV or player
compatible with AVR-2310CI and HDMI control functions, you
can perform the following operations by setting the HDMI control
function of each device.
Getting Started
Convenient functions
ENGLISH
Getting Started
Adjust the Volume of the
Different Speakers
Saving Frequently Used Settings
(Quick Select Function)
You can adjust the channel level either according to the playback
sources or to suit your taste, as described below.
Connections
Adjust the volume of the different speakers
1
Press
.
CHANNEL
Front
•Three sets of settings can be saved.
LEVEL
L
0.0dB
R
0.0dB
Settings
Subwoofer
Surround
0.0dB
R
0.0dB
S.Back
L
0.0dB
Surround
L
Fader
0.0dB
Front
Rear
Playback
Select
Multi-Zone
2
Press ui to select the speaker.
Front
The speaker that can be set switches each
time one of the buttons is pressed.
Remote Control
3
Press o p to adjust the volume.
bIn the case of a subwoofer, reducing the volume when it is at
“–12 dB” will change the setting to “OFF” (none).
Information
If headphones are plugged in, the headphones settings screen
appears.
Troubleshooting
Specifications
1
2
or i to select “Fader”, then select the item
to be adjusting using o or p.
Use
Press o p to adjust the volume of the speakers.
•The fader function does not affect the subwoofer.
•The fader can be adjusted until the volume of the speaker adjusted
to the lowest value is –12 dB.
55
ZONE2 settings
It is also possible to save three settings for ZONE2.
Saving the settings
1 Set the items below to the settings you want to save.
q Input source (vpage 42)
w Input Mode (vpage 39)
e Surround Mode (vpage 46)
r Audyssey Settings (MultEQ, Dynamic EQ, Dynamic
Volume) (vpage 50)
t Front Speaker Setup (vpage 30)
y Volume setting (vpage 42)
u Video select (vpage 38)
2
Press and hold the desired
appears on the display.
The current settings will be memorized.
until “Memory”
Front
Set the remote control unit’s
device selector switches as
shown on right.
2
Perform steps 1 and 2 under “MAIN ZONE
settings”.
Various Memory Functions
Personal Memory Plus Function
This function sets the settings (input mode, surround mode, MultEQ,
Dynamic EQ, Dynamic Volume, audio delay etc.) last selected for the
individual input sources.
Last Function Memory
Adjusting the volume of groups of speakers
(Fader Function)
This function lets you adjust (fade) the sound from all the front (Front
speaker / center speaker / Front Height speaker) or rear (Surround speaker /
Surround Back speaker) speakers at once.
“Quick Select Name” (vpage 34).
1
MAIN ZONE settings
0.0dB
R
S.Back
Saving the settings
0.0dB
Center
Front
This function allows you to save all the settings shown in step
1. When frequently used settings are saved, they can easily be
set again the next time you want to use them. This function also
allows you to always enjoy the same playback environment.
nNaming Quick Select settings
GQuick Select DefaultsH
Quick Select 1
Quick Select 2
Quick Select 3
Input Source
DVD
SAT/CBL
VCR/iPod
Volume
–40 dB
–40 dB
–40 dB
Backup Memory
Calling the settings out
Press the
at which the
settings you want to call out are saved.
This stores the settings as they were directly before the standby mode
was set.
When the power is turned back on, the settings are restored to as they
were directly before the standby mode was set.
Front
NOTE
Input sources stored with the quick select function cannot be selected
if they have been deleted at menu “Source Delete” (vpage 33). In
this case, store them again.
The various settings are backed up for about 1 week, even if the power
is turned off or the power cord is disconnected.
ENGLISH
qZONE2 playback by speaker output
wZONE2 playback by audio output (PRE OUT) (using an
external amplifier))
The audio signals connected to the AVR-2310CI’s ZONE2 output
terminals (ZONE2 OUT) are output to the ZONE2’s amplifier and played
with that amplifier.
Connection (ZONE2)
Playback
The operation is the same for “q ZONE2 playback by speaker
output” and “w ZONE2 playback by audio output”.
1
Set the remote control unit’s
“device selector switches” as
shown on right.
Turn on the AVR-2310CI’s power.
(vpage 20 “Turning the Power On”)
With the Amp Assign function, Zone 2 audio signals are output from
the AVR-2310CI's SURR BACK/AMP ASSIGN terminals.
R
AVR-2310CI
L
” indicator lights on the
bThe power can be turned on by pressing the one of
while in the standby mode.
n Connecting the speakers
4
Use the input source selector to choose the input
ZONE2
R
w
(R)
q
w
"69
*/
q
source.
The selected input source is shown on the display.
NOTE
Adjusting the volume (for “q ZONE2 playback by
speaker output”)
n Necessary settings
Use
• Adjust the volume on the connected amplifier.
• Also be sure to read the operating instructions of the connected
devices.
NOTE
•We recommend using high quality pin-plug cables for audio
connections in order to prevent noise.
•It is not possible to play the digital audio signals input from the
HDMI, COAXIAL or OPTICAL terminals in ZONE2. Play using analog
connections (in stereo).
to adjust the volume.
GVariable rangeH – – –
–80dB(1) ~ –40dB(41) ~ +18dB(99)
b The volume can be adjusted up to the level set at “Vol. Limit”
(vpage 33).
b The volume display is the display set at “Volume Display”
(vpage 33).
or “w ZONE2 playback by audio output”, adjust the volume on the
F
connected amplifier.
56
Specifications
• Set the AMP ASSIGN mode to “ZONE2”.
“Amp Assign” (vpage 28)
• Perform the settings at “ZONE2 Setup”.
“Making the ZONE2 settings” (vpage 33)
Troubleshooting
When “SOURCE” is selected for the input source, the sound being
played in the MAIN ZONE is played. No sound is output if a digital
audio input source is being played in the MAIN ZONE.
Information
(L)
L
Remote Control
Connecting and setting the speakers
to turn on the ZONE2 power.
When the power turns on, the “
display.
Multi-Zone
3
Press
Preparations
Rear
Playback
2
MAIN ZONE
Settings
q ZONE2 Playback by Speaker
Output
w ZONE2 Playback by Audio
Output
Connections
2-channel sound can be played in rooms other than the MAIN
ZONE where multichannel sound is played.
There are two methods to do this, as described below. Choose
one of the methods.
Getting Started
Playing 2-Channel Sound in ZONE2 (Multizone Function)
ENGLISH
Getting Started
Operating the Connected Devices by Remote Control Unit
iPod
Connections
Main Remote Control Unit
(RC-1117)
Registering Preset Codes
Settings
DENON and other makes of components can be operated by setting
the preset memory.
Playback
1 Switch
.
MAIN/TV : To register a TV
DEVICE : To operate a Blu-ray disc player, DVD player,
Multi-Zone
Digital video recorder, video deck, satellite
receiver, cable TV or CD player
Remote Control
2
Set
DVD/HDP : DVD player or Blu-ray disc player
DVR/VCR : Digital video recorder or video deck
SAT/CBL : Satellite receiver or cable TV
Information
CD
Troubleshooting
3 Press
time.
2
at the same
Rear
Specifications
Press
~
and input the 3digit number of the brand of the
component to be preset. The numbers
are shown in the Preset Code Table
(vEnd of this manual).
store the codes of another component in the
5 Tomemory,
repeat steps 1 to 4.
57
.
MAIN/TV : To operate the TV or iPod
DEVICE : To operate a Blu-ray disc player, DVD player,
Set
MAIN
TV
: iPod
: TV
DVD/HDP : DVD player or Blu-ray disc player
DVR/VCR : DVD recorder or video deck
SAT/CBL : Satellite receiver or cable TV
CD
: CD player
3 Operate the component.
b For details, refer to the component’s operating instructions.
NOTE
Depending on the model and year of manufacture, this function cannot
be used for some models, even if they are of makes listed in the list
of preset codes.
1
2
MEMORY
TU/PAGE
Play / Pause
Stop
MEMORYz1
Page up/down z1
8 9
Auto search
(cue)
uio p
ENTER
Cursor
Enter
Pause
3
Press and
hold
to the component you want to operate.
: CD player
and
DEVICE SELECT
Digital video recorder, video deck, satellite
receiver, cable TV or CD player
The indicator starts flashing.
4
1
Switch
: TV
Front
Operating Registered Devices
to the component to be registered.
TV
•Some manufacturers use more than one type of remote control code.
Refer to the included list of preset codes to change the number and
verify correct operation.
•VDP (Video Disc Player) can be preset when
is set to “DVD/
HDP”.
•The preset memory can be set for one component only among the
following: DVD/HDP, DVR/VCR and SAT/CABLE.
Front
SEARCH
RETURN
Once
Page search
Browse/Remote mode switching
mode switching
z2
Return
z1 : This operation is possible when using a
DENON ASD-3N or ASD-3W Control Dock
for iPod.
z2 : This operation is possible when using a
DENON ASD-1R or ASD-11R Control Dock
for iPod.
ENGLISH
TV
Blu-ray Disc / DVD Player
Front
(fast-reverse / fast-forward)
Channelz
SKIP +
Switching the input
6 7
Front
Channels
CH + –
MENU
uio p
ENTER
SETUP
RETURN
Disc skip
Manual search
(fast-reverse / fast-forward)
Auto search (cue)
Calling out the menus
Cursor operation
Enter setting
Setup
Return
Front
Rear
0 ~ 9, +10
Default setting
(Preset code)
Special Remarks
Calling out the top menus
Channels
HITACHI (008)
q, w
Rear
HITACHI (014)
0 ~ 9, +10
Default setting
(Preset code)
Special Remarks
Number input / Track selection
BD Player
DVD Player
DENON DENON (121)
(111)*
q, w
Troubleshooting
q
z : When the punch through function
(vpage 59) is set, this functions as the
button for the device for which punch
through is set.
* : The initial setting of Preset code is 111 (DVD Player).
Rear
Specifications
Rear
6 7
Power on / Standby
Play
Stop
Pause
Manual search
(fast-reverse / fast-forward)
Switch channels (+, –)
Calling out the menus
Cursor operation
Enter setting
Setup
Return
Information
SOURCE SELECT /
TOP MENU
Rear
1 ~ 12
Default setting
(Preset code)
Special Remarks
8 9
MENU
uio p
ENTER
SETUP
RETURN
–
ON/SOURCE
1
2
SHIFT, 3
Remote Control
d : TV Volume (+)
f : TV Volume (–)
TV MUTE
Calling out the menus
Cursor operation
Enter setting
Setup
Return
Power off
Power on or Power on / Standby
Play
Stop
Pause
BD Player
DVD Player
Multi-Zone
Front
MUTE
MENU
uio p
ENTER
SETUP
RETURN
POWER OFF
ON/SOURCE
1
2
SHIFT, 3
Playback
VOLUME df
Power on / Standby
Playz
Pausez
Stopz
Manual search z
DEVICE SELECT
Settings
CH + –
TV INPUT
DEVICE SELECT
Connections
6 7
Front
Front
DEVICE SELECT
ON/SOURCE
1
3
2
Digital Video Recorder / Video Deck
Getting Started
Main Remote Control Unit (RC-1117)
Rear
【Special Remarks】
q Only one device can be set in the preset memory for each mode.
When a new preset code is registered, the existing code is automatically erased.
w For some brands, the DVD remote control buttons may have different function names.
Check beforehand.
58
ENGLISH
Getting Started
Main Remote Control Unit (RC-1117)
Satellite receiver/Cable TV
Connections
Front
Front
DEVICE SELECT
DEVICE SELECT
Settings
ON/SOURCE
1
3
2
Playback
6 7
Multi-Zone
CH + –
uio p
ENTER
MENU
SETUP
RETURN
Remote Control
Front
CD Player
(fast-reverse / fast-forward)
Channelz
Information
Default setting
(Preset code)
Special Remarks
6 7
Cursor operation
Enter setting
Calling out the menus
Setup
Return
Rear
0 ~ 9, +10
POWER OFF
ON/SOURCE
1
2
SHIFT, 3
SKIP +
Power on / Standby
Playz
Pausez
Stopz
Manual search z
8 9
Power off
Power on or Power on / Standby
Play
Stop
Pause
Disc skip +
Manual search
(fast-reverse / fast-forward)
Auto search (cue)
Rear
Front
Channels
Satellite
Cable TV
Receiver
0 ~ 9, +10
Number input / Track selection
Default setting
(Preset code)
DENON (111)
Special Remarks
q
The Blu-ray disc Player/DVD player, Digital Video recorder, video deck,
or CD player can be operated as described below even when
is set to the “SAT/CBL” or “TV” position.
•Play
•Stop
•Pause
•fast-forward
•fast-reverse
•Auto Search
1 Switch
.
MAIN/TV : Assigning TV buttons to operate other devices
DEVICE
: Assigning satellite receiver or cable TV buttons to
operate other devices
2 Switch
.
TV
: Assigning TV buttons to operate other devices
SAT/CBL : Assigning satellite receiver or cable TV buttons to
operate other devices
3 Press
and
at the same time.
4
Refer to the table below and input the number
corresponding to the device to be assigned.
q
Troubleshooting
z : When the punch through function
(vpage 59) is set, this functions as the
button for the device for which punch
through is set.
Device to be assigned
iPod, Tuner
CD Player
Blu-ray Disc Player / DVD Player
Specifications
DVD Recorder, Video Deck
No setting
Rear
Rear
【Special Remarks】
q Only one device can be set in the preset memory for each mode.
When a new preset code is registered, the existing code is automatically erased.
w For some brands, the DVD remote control buttons may have different function names.
Check beforehand.
59
Rear
The indicator starts flashing.
ABC (009)
–
Assigning buttons that are Not Used to
Operate Other Devices
(Punch Through Function)
This is set to “No setting” upon purchase.
Numbers
ENGLISH
z : This button can be operated when using a
control dock for iPod ASD-3N/3W.
Dolby Digital Plus is an improved Dolby Digital signal format that is
compatible with up to 7.1-channels of discrete digital sound and also
improves sound quality thanks to extra data bit rate performance. It
is upwardly compatible with conventional Dolby Digital, so it offers
greater flexibility in response to the source signal and the conditions
of the playback equipment.
Dolby TrueHD
Dolby Pro Logic g
Dolby Pro Logic gz
Dolby Pro Logic gz introduces a new dimension to Home Entertainment
through the addition of a pair of front height channels. Compatible with
stereo, 5.1 and 7.1 content, Dolby Pro Logic gz provides enhanced
spaciousness, depth and dimension to movies, concert video and
videogame playback while maintaining the full integrity of the source
mix.
Dolby Pro Logic gz identifies and decodes spatial cues that occur
naturally in all content, directing this information to the front height
channels, complementing the performance of left and right surround
sound speakers. Content that is encoded with Dolby Pro Logic
gz height channel information can be even more revealing, with
perceptually discrete height channel information bringing an exciting
new dimension to home entertainment. Dolby Pro Logic gz, with
front height channels is also an ideal alternative for households that
cannot support the placement of back surround speakers of a typical
7.1 channel system but may have bookshelf space available to support
the addition of height speakers.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are trademarks of
Dolby Laboratories.
Dolby Pro Logic g is a matrix decoding technology developed by Dolby
Laboratories.
Regular music such as that on CDs is encoded into 5-channels to
achieve an excellent surround effect.
The surround channel signals are converted into stereo and full band
signals (with a frequency response of 20 Hz to 20 kHz or greater)
to create a “three-dimensional” sound image offering a rich sense of
presence for all stereo sources.
60
Specifications
Dolby TrueHD is a high definition audio technology developed by Dolby
Laboratories, using lossless coding technology to faithfully reproduce
the sound of the studio master.
This format is compatible with a maximum sampling frequency of 96
kHz and up to 7.1-channels, so it is used for applications particularly
prioritizing sound quality.
Dolby Digital EX is a 6.1-channel surround format proposed by Dolby
Laboratories that allows users to enjoy in their homes the “DOLBY
DIGITAL SURROUND EX” audio format jointly developed by Dolby
Laboratories and Lucas Films.
The 6.1 channels of sound, including surround back channels, provide
improved sound positioning and expression of space.
Troubleshooting
Stop
Play/pause
Dolby Digital Plus
Dolby Digital EX
Information
2
1/3
SHIFT
Dolby Digital is a multichannel digital signal format developed by Dolby
Laboratories.
A total of 5.1-channels are played: 3 front channels (“FL” , “FR” and
“C”), 2 surround channels (“SL” and “SR”) and the “LFE” channel for
low frequencies.
Because of this, there is no crosstalk between channels and a realistic
sound field with a “three-dimensional” feeling (sense of distance,
movement and positioning) is achieved.
A real, overpowering sense of presence is achieved when playing
movie sources in AV rooms as well.
Remote Control
Auto search
QUICK SELECT
MUTE
AM
FM
TUNING d f
Dolby Digital
Multi-Zone
8 9
M. ZONE CALL
Dolby Surround
Dolby Pro Logic gx is a further improved version of the Dolby Pro Logic
g matrix decoding technology.
Audio signals recorded in 2-channels are decoded to achieve a natural
sound with up to 7.1-channels.
There are 3 modes: “Music” suited for playing music, “Cinema”
suited for playing movies, and “Game” which is optimized for playing
games.
Playback
CH + –
VOLUME
REPEAT
RANDOM
iPod DIRECT PLAY
FAVORITES
DIRECT PLAY
ZONE2 POWER OFF
ZONE2 POWER ON
Switching the input source
Input source switches to the
MAIN ZONE’s input source
QUICK SELECT selection
Muting
AM selection
FM selection
Tuning
Preset channel memory block
selection
Preset channel selection
Adjustment of volume
Repeat
Random
Auto Play
The files in “Favorites” are
played. z
The AVR-2310CI is equipped with a digital signal processing circuit that
lets you play program sources in the surround mode to achieve the
same sense of presence as in a movie theater.
Dolby Pro Logic gx
Settings
ZONE2 OFF
ZONE2 ON
SOURCE SELECT
Surround
Connections
The sub remote control unit (RC-1119) included with the AVR-2310CI
can be used as the exclusive multi-zone remote control unit.
b The following describes operation for the selected zone.
• Turning the multi-zone power on and off
• Selecting the input source to be played
• Adjusting and temporarily muting the multi-zone volume
• Listening to the tuner (TUNER and SIRIUS)
• Operating an iPod
Other Information
Getting Started
Sub Remote Control Unit
(RC-1119)
ENGLISH
Getting Started
Surround
DTS Surround
DTS Digital Surround
Connections
DTS Digital Surround is the standard digital surround format of DTS,
Inc., compatible with a sampling frequency of 44.1 or 48 kHz and up
to 5.1-channels of digital discrete surround sound.
Settings
DTS-HD High Resolution Audio
Playback
Multi-Zone
DTS-HD High Resolution Audio is an improved version of the
conventional DTS, DTS-ES and DTS 96/24 signals formats, compatible
with sampling frequencies of 96 or 48 kHz and up to 7.1-channels
of discrete digital sound. High data bit rate performance provides
high quality sound. This format is fully compatible with conventional
products, including conventional DTS digital surround 5.1-channel
data.
DTS-HD Master Audio
DTS 96/24
Audyssey Dynamic Volume™
DTS 96/24 is a digital audio format enabling high sound quality
playback in 5.1-channels with a sampling frequency of 96 kHz and 24
bit quantization on DVD-Video.
Audyssey Dynamic Volume solves the problem of large variations in
volume level between television programs, commercials, and between
the soft and loud passages of movies.
Audyssey Dynamic EQ is integrated into Dynamic Volume so that as
the playback volume is adjusted automatically, the perceived bass
response, tonal balance, surround impression, and dialog clarity
remain the same.
Manufactured under license under U.S. Patent #’s: 5,451,942;
5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 7,212,872;
7,333,929; 7,392,195; 7,272,567 & other U.S. and worldwide patents
issued & pending. DTS is a registered trademark and the DTS
logos, Symbol, DTS-HD and DTS-HD Master Audio are trademarks
of DTS, Inc.© 1996-2008 DTS, Inc. All Rights Reserved.
Audyssey
Audyssey MultEQ®
Remote Control
Information
Troubleshooting
DTS-HD Master Audio is DTS, Inc’s lossless audio format compatible
with up to 96 kHz/7.1-channels. The lossless audio coding technology
faithfully reproduces the sound of the studio master. It is fully
compatible with conventional products, including conventional DTS
digital surround 5.1-channel data.
Audyssey MultEQ is a room equalization solution that calibrates any
audio system so that it can achieve optimum performance for every
listener in a large listening area. Based on several room measurements,
MultEQ calculates an equalization solution that corrects for both
time and frequency response problems in the listening area and also
performs a fully automated surround system setup.
DTS-ES™ Discrete 6.1
Audyssey Dynamic EQ™
DTS-ES™ Discrete 6.1 is a 6.1-channel discrete digital audio format
adding a surround back (SB) channel to the DTS digital surround sound.
Decoding of conventional 5.1-channel audio signals is also possible
according to the decoder.
Audyssey Dynamic EQ solves the problem of deteriorating sound
quality as volume is decreased by taking into account human perception
and room acoustics. Audyssey Dynamic EQ works in tandem with
Audyssey MultEQ to provide well-balanced sound for every listener
at any volume level.
DTS-ES™ Matrix 6.1
Specifications
DTS-ES™ Matrix 6.1 is a 6.1-channel discrete digital audio format
inserting a surround back (SB) channel to the DTS digital surround
sound through matrix encoding. Decoding of conventional 5.1-channel
audio signals is also possible according to the decoder.
DTS NEO:6™ Surround
DTS NEO:6™ is a matrix decoding technology for achieving 6.1channel surround playback with 2-channel sources. It includes “DTS
NEO:6 Cinema” suited for playing movies and “DTS NEO:6 Music”
uited for playing music.
61
Manufactured under license from Audyssey Laboratories. U.S.
and foreign patents pending. Audyssey MultEQ® is a registered
trademark of Audyssey Laboratories. Audyssey Dynamic EQ™ is a
trademark of Audyssey Laboratories. Audyssey Dynamic Volume™
is a trademark of Audyssey Laboratories.
ENGLISH
Surround Modes and Parameters
Signals and adjustability in the different modes
Surround mode
Parameter (default values are shown in parentheses)
Surround Front Height
Su­b­­­­woofer
Back L/R
L/R
LFE
S
D
D
D
D
D
S (OFF)
S (0dB)
A
A
A
A
A
A
A
S
MULTI CH DIRECT
S
D
D
D
A
D
A
S (0dB)
S (ON)
S
A
A
A
A
A
A
A
STEREO
S
A
A
A
A
D
S (OFF)
S (0dB)
A
A
A
A
A
A
A
A
S (Auto)
EXT. IN
S
D
D
D
A
D
A
A
A
A
A
A
A
A
A
A
A
MULTI CH IN
S
D
D
D
A
D
A
S (0dB)
S (ON)
S
S (OFF)
A
A
A
A
A
A
DOLBY PRO LOGIC gx
S
D
D
D
A
D
S (OFF)
A
A
S
S (NOTE1) S (Cinema)
A
A
A
A
S (Auto)
DOLBY PRO LOGIC g
S
D
D
A
A
D
S (OFF)
A
A
S
S (NOTE2) S (Cinema)
A
A
A
A
S (Auto)
DTS NEO:6
S
D
D
D
A
D
S (OFF)
A
A
S
S (NOTE1) S (Cinema)
A
A
A
A
A
DOLBY PRO LOGIC gz
S
D
D
A
D
D
S (OFF)
A
A
A
S (OFF)
A
A
A
A
A
A
DOLBY DIGITAL
S
D
D
D
D
D
S (OFF)
S (0dB)
S (ON)
S
S (OFF)
A
A
A
A
A
A
DOLBY DIGITAL Plus
S
D
D
D
D
D
S (OFF)
S (0dB)
S (ON)
S
S (OFF)
A
A
A
A
A
A
DOLBY TrueHD
S
D
D
D
D
D
S (OFF)
S (0dB)
S (ON)
S
S (OFF)
A
A
A
A
A
S (Auto)
DTS SURROUND
S
D
D
D
D
D
S (OFF)
S (0dB)
S (ON)
S
S (OFF)
A
A
A
A
A
A
DTS 96/24
S
D
D
D
D
D
S (OFF)
S (0dB)
S (ON)
S
S (OFF)
A
A
A
A
A
A
DTS-HD
S
D
D
D
D
D
S (OFF)
S (0dB)
S (ON)
S
S (OFF)
A
A
A
A
A
A
5CH/7CH STEREO
S
D
D
D
D
D
S (OFF)
S (0dB)
A
S
A
A
A
A
A
A
A
ROCK ARENA
S
D
D
D
D
D
S (OFF)
S (0dB)
A
S
A
A
S (Medium)
S (10)
A
A
A
JAZZ CLUB
S
D
D
D
D
D
S (OFF)
S (0dB)
A
S
A
A
S (Medium)
S (10)
A
A
A
MONO MOVIE
S
D
D
D
D
D
S (OFF)
S (0dB)
A
S
A
A
S (Medium)
S (10)
A
A
A
VIDEO GAME
S
D
D
D
D
D
S (OFF)
S (0dB)
A
S
A
A
S (Medium)
S (10)
A
A
A
MATRIX
S
D
D
D
D
D
S (OFF)
S (0dB)
A
S
A
A
A
A
S (30 ms)
A
A
VIRTUAL
S
A
A
A
A
D
S (OFF)
S ( 0dB)
A
A
A
A
A
A
A
A
A
z2
z1
Surround
Back
Cinema EQ.
Mode
Room Size
Effect
Level
Delay Time
Subwoofer
DRC
z3
S (Auto)
Multi-Zone
PURE DIRECT, DIRECT
z1
AFDM
Playback
Center
Remote Control
Information
S: Signal / Adjustable
A : No signal / Not adjustable
NOTE1 :This parameter is available when the menu “Mode” (vpage 48) is set to “Cinema”.
NOTE2 :T his parameter is available when the menu “Mode” (vpage 48) is set to “Cinema” or “PL”.
NOTE:
z1 :When playing Dolby Digital and DTS signals.
z2 :When playing Dolby Digital, DTS and Linear PCM (multi ch).
z3 :When playing Dolby TrueHD signal.
Troubleshooting
S: Signal / Adjustable
A : No signal / Not adjustable
D:Turned on or off by speaker configuration setting
D. Comp
Settings
Front L/R
Surround
L/R
Connections
Channel output
Getting Started
Surround
Specifications
62
ENGLISH
Getting Started
Surround
Signals and adjustability in the different modes
Parameter (default values are shown in parentheses)
Surround mode
PRO LOGIC g/gx MUSIC mode only
NEO:6 MUSIC
mode only
EXT. IN only
Connections
Center Image Subwoofer ATT
Tone Control
(NOTE4)
MultEQ
Dynamic EQ
(NOTE5)
Dynamic
Volume
(NOTE6)
RESTORER
(NOTE7)
A
Settings
Panorama
Dimension
Center Width
PURE DIRECT, DIRECT
A
A
A
A
A
A
A
A
A
MULTI CH DIRECT
A
A
A
A
A
A
A
A
A
A
STEREO
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
EXT. IN
A
A
A
A
S
A
A
A
A
A
MULTI CH IN
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
A
DOLBY PRO LOGIC gx
S (OFF)
S (3)
S (3)
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
DOLBY PRO LOGIC g
Playback
Multi-Zone
Remote Control
Information
S (OFF)
S (3)
S (3)
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
DTS NEO:6
A
A
A
S (0.3)
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
DOLBY PRO LOGIC gz
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
A
DOLBY DIGITAL
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
A
DOLBY DIGITAL Plus
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
A
DOLBY TrueHD
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
A
DTS SURROUND
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
A
DTS-96/24
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
A
DTS-HD
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
A
5CH/7CH STEREO
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
ROCK ARENA
A
A
A
A
A
S (NOTE3)
S (OFF)
S (OFF)
S (OFF)
S
JAZZ CLUB
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
MONO MOVIE
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
VIDEO GAME
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
MATRIX
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
VIRTUAL
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
Troubleshooting
S: Adjustable
A : Not adjustable
NOTE3 :BASS +6 dB, TREBLE +4 dB
NOTE4 :Cannot be set when the “Dynamic EQ” (vpage 51) setting is “ON”.
NOTE5 :Cannot be set when the “MultEQ” (vpage 50) setting is “OFF”.
NOTE6 :Cannot be set when the “Dynamic EQ” (vpage 51) setting is “OFF”.
NOTE7 :“RESTORER” can be set for analog or PCM 48 kHz or 44.1 kHz input signals.
Specifications
63
ENGLISH
Differences in Surround Mode Names Depending on the Input Signals
Input signals
Button
PCM
Linear
ANALOG
PCM
(multi ch)
Linear
PCM
(2ch)
DTS-HD
Master
Audio
DTS
DTS-HD
High
Resolution
Audio
DTS ES
DTS ES
DSCRT
MTRX
(With Flag) (With Flag)
DOLBY
DTS
(5.1ch)
DTS
96/24
DOLBY DIGITAL
DOLBY
DOLBY
DIGITAL
TrueHD
Plus
DOLBY
DIGITAL
EX (With
Flag)
DOLBY
DOLBY
DIGITAL EX
DIGITAL
(With no
(5.1/5/4ch)
Flag)
DOLBY
DIGITAL
(4/3ch)
DOLBY
DIGITAL
(2ch)
STANDARD
DTS-HD MSTR
A
A
A
F
A
A
A
A
A
A
A
A
A
A
A
A
DTS-HD HI RES
A
A
A
A
F
A
A
A
A
A
A
A
A
A
A
A
z1 z3
A
A
A
A
A
F D
A
A
A
A
A
A
A
A
A
A
DTS ES MTRX6.1
z1 z3
A
A
A
A
A
A
F D
A
A
A
A
A
A
A
A
A
DTS SURROUND
A
A
A
A
A
S
S
F
A
A
A
A
A
A
A
A
DTS 96/24
A
A
A
A
A
A
A
A
F
A
A
A
A
A
A
A
A
A
A
S
S
S
S
S
S
A
A
A
A
A
A
A
DTS (–HD) + PLgx MUSIC
z1 z3
A
A
A
S
S
S
S
S
S
A
A
A
A
A
A
A
DTS (–HD) + PLgz
z1 z4
A
A
A
S
S
S
S
S
S
A
A
A
A
A
A
A
DTS (–HD) + NEO:6
z1 z3
A
A
A
S
S
A
S
S
S
A
A
A
A
A
A
A
DTS NEO:6 CINEMA
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
DTS NEO:6 MUSIC
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
DOLBY TrueHD
A
A
A
A
A
A
A
A
A
F
A
A
A
A
A
A
DOLBY DIGITAL+
A
A
A
A
A
A
A
A
A
A
F
A
A
A
A
A
DOLBY SURROUND
z1 z3
A
A
A
A
A
A
A
A
A
A
A
S
S
S
S
A
DOLBY (D+) (HD) +EX
z1 z3
A
A
A
A
A
A
A
A
A
S
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
S
F
F
F
A
DOLBY DIGITAL
A
A
A
A
A
A
A
A
A
S
S
F D
S
S
S
A
DOLBY (D) (D+) (HD) +PLgx MUSIC
z1 z3
A
A
A
A
A
A
A
A
A
S
S
S
S
S
S
A
DOLBY (D) (D+) (HD) +PLgz
z1 z4
A
A
A
A
A
A
A
A
A
S
S
S
S
S
S
A
DOLBY PRO LOGIC gx CINEMA
z3
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
DOLBY PRO LOGIC gx MUSIC
z3
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
DOLBY PRO LOGIC gx GAME
z3
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
DOLBY PRO LOGIC gz
z4
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
DOLBY PRO LOGIC g CINEMA
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
DOLBY PRO LOGIC g MUSIC
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
DOLBY PRO LOGIC g GAME
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
DOLBY PRO LOGIC
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
NOTE:
z1: This mode is not available when the surround back speaker setup is set to “None”.
z2: This mode is not available when the surround back speaker setup is set to “1sp” or “None”.
z3: Can be set when “Amp Assign” is set to “Normal”
.
z4: Not selectable when “Amp Assign” is set to anything other than “Front Height”
.
F : Mode selectable in initial status
D : Mode fixed when “AFDM” is “ON”
S : Selectable mode
A : Non-selectable mode
64
Specifications
z2 z3
Troubleshooting
DOLBY (D) (D+) (HD) +PLgx CINEMA
Information
DOLBY DIGITAL EX
Remote Control
z2 z3
Multi-Zone
DTS (–HD) + PLgx CINEMA
Playback
DTS ES DSCRT6.1
Settings
DTS SURROUND
Connections
Surround mode
Note
DTS-HD
Getting Started
Surround
ENGLISH
Getting Started
Surround
Input signals
Button
PCM
Surround mode
Note
Connections
Linear
ANALOG
PCM
(multi ch)
DTS-HD
DTS
Linear
PCM
(2ch)
DTS-HD
Master
Audio
DTS-HD
High
Resolution
Audio
DTS ES
DTS ES
DSCRT
MTRX
(With Flag) (With Flag)
DOLBY
DTS
(5.1ch)
DTS
96/24
DOLBY DIGITAL
DOLBY
DOLBY
DIGITAL
TrueHD
Plus
DOLBY
DIGITAL
EX (With
Flag)
DOLBY
DOLBY
DIGITAL
DIGITAL
EX (With
(5.1/5/4ch)
no Flag)
DOLBY
DIGITAL
(4/3ch)
DOLBY
DIGITAL
(2ch)
STANDARD
MULTI CH IN
MULTI CH IN
Settings
Playback
A
F
A
A
A
A
A
A
A
A
A
A
A
A
A
A
MULTI IN + PLgx CINEMA
z2 z3
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
MULTI IN + PLgx MUSIC
z1 z3
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
MULTI IN + PLgz
z1 z5
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
MULTI IN + Dolby EX
z1 z3
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
z3
A
F D (7.1)
A
A
A
A
A
A
A
A
A
A
A
A
A
A
MULTI CH IN 7.1
DIRECT
A
S
S
S
S
S
S
S
S
S
S
S
S
S
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
MULTI CH DIRECT
M DIRECT + PLgx CINEMA
z2 z3
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
M DIRECT + PLgx MUSIC
z1z3
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
M DIRECT + PLgz
z1z5
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
Remote Control
S
Multi-Zone
DIRECT
M DIRECT + Dolby EX
z1 z3
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
z3
A
S (7.1)
A
A
A
A
A
A
A
A
A
A
A
A
A
A
M DIRECT 7.1
PURE DIRECT
PURE DIRECT
S
A
S
S
S
S
S
S
S
S
S
S
S
S
S
S
MULTI CH PURE DIRECT
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
Information
M PURE D + PLgx CINEMA
z2 z3
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
M PURE D + PLgx MUSIC
z1 z3
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
M PURE D + PLgz
z1 z5
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
M PURE D + Dolby EX
z1 z3
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
z3
A
S (7.1)
A
A
A
A
A
A
A
A
A
A
A
A
A
A
z4
M CH PURE DIRECT 7.1
Troubleshooting
DSP SIMULATION
5CH/7CH STEREO
Specifications
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
ROCK ARENA
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
JAZZ CLUB
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
MONO MOVIE
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
VIDEO GAME
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
MATRIX
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
VIRTUAL
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
F
S
F
S
S
S
S
S
S
S
S
S
S
S
S
S
STEREO
STEREO
NOTE :
z1: This mode is not available when the surround back speaker setup is set to “None”.
z2: This mode is not available when the surround back speaker setup is set to “1sp” or “None”.
z3: Can be set when “Amp Assign” is set to “Normal”
.
z4: If the surround back speaker setup is set to “None”, then “5CH STEREO” is displayed.
z5: Not selectable when “Amp Assign” is set to anything other than “Front Height”
.
65
F : Mode selectable in initial status
D : Mode fixed when “AFDM” is “ON”
S : Selectable mode
A : Non-selectable mode
ENGLISH
Video Convert
VIDEO
VIDEO
VIDEO
S (VIDEO)
S-VIDEO
S-VIDEO
S-VIDEO
S-VIDEO
S (S-VIDEO)
A
COMPONENT
COMPONENT
A (S-VIDEO) z3
A (S-VIDEO) z3
A (S-VIDEO) z3
A (COMPONENT) z2
A z2
A
A z2
A
A (COMPONENT) z3
A
S (VIDEO)
A
A (COMPONENT) z3
A (S-VIDEO)
S (S-VIDEO)
A (S-VIDEO)
A (COMPONENT) z3
A (S-VIDEO)
S (S-VIDEO)
A (S-VIDEO)
A (COMPONENT) z3
A (COMPONENT) z3
A (VIDEO)
S (VIDEO)
A (VIDEO)
A (COMPONENT) z3
A (S-VIDEO)
S (S-VIDEO)
A (S-VIDEO)
A (COMPONENT) z3
A (S-VIDEO)
S (S-VIDEO)
A (S-VIDEO)
A (COMPONENT) z3
A z2
A (VIDEO) z2
VIDEO
A
COMPONENT
COMPONENT
S (COMPONENT)
S-VIDEO
S-VIDEO
A
COMPONENT
COMPONENT
S (COMPONENT)
S-VIDEO
S-VIDEO
A
A (COMPONENT)
S (S-VIDEO)
COMPONENT
COMPONENT
S (COMPONENT)
A (COMPONENT) z3
A
A
S-VIDEO
HDMI
A
COMPONENT
A
A
A
A
S-VIDEO
HDMI
S-VIDEO
A (S-VIDEO) z2
A z2
A z2
A (VIDEO) z2
A (S-VIDEO) z2
A (S-VIDEO) z2
A (COMPONENT) z2
A
VIDEO
A
VIDEO
A
VIDEO
A
VIDEO
Only the GUI menu
is displayed
A z2
A
VIDEO
A
VIDEO
A
VIDEO
S ( ):Superimposed on the picture indicated in ( ).
A ( ) :Only the picture in ( ) is output.
A: Neither the picture nor the GUI menu is output.
z2:Only the GUI menu is displayed when no HDMI monitor is connected or the HDMI
monitor’s power is not on.
z3:When no HDMI monitor is connected or the HDMI monitor’s power is “OFF”, the
GUI menu is superimposed on the picture indicated in ( ).
66
Specifications
A
COMPONENT
A (S-VIDEO) z2
S (HDMI)
Troubleshooting
S-VIDEO
A z2
A z2
VIDEO
VIDEO
A
A (COMPONENT) z3
S-VIDEO
S-VIDEO
COMPONENT
A (COMPONENT)
S (S-VIDEO)
A
VIDEO
S-VIDEO
S-VIDEO
A (COMPONENT) z3
Information
A
A (VIDEO) z3
A (COMPONENT)
S (VIDEO)
COMPONENT
A
A (VIDEO) z3
A (COMPONENT)z3
A
COMPONENT
A (VIDEO) z3
S (COMPONENT)
A
VIDEO
VIDEO
Only the GUI menu is displayed
VIDEO
A
GUI menu displayed
COMPONENT
S-VIDEO
Remote Control
• The main zone video conversion function is compatible with the following
formats: NTSC, PAL, SECAM, NTSC4.43, PAL -N, PAL -M and PAL -60.
• When SECAM signals of video input are up-converted, the signals are
output in PAL format from the S-Video and Video connectors.
• The GUI menu display cannot be superimposed when x.v.Color signals
and computer’s resolution (e.g. VGA) are input.
HDMI
Multi-Zone
S: Video signal input present
A : No video signal input
z1 : When no HDMI monitor is connected or the HDMI monitor’s power is
not on
VIDEO
A
Playback
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
HDMI
A
Settings
ON
ON
ON
VIDEO
A
S
A
S
A
A
A
S
S
S
S
A
A
A
A
S
S
S
S
A
S
A
S
A
S
A
S
S
A
S
A
S
A
S
A
S
A
S
A
S
A
S
MAIN ZONE MONITOR OUT
Output Signals
COMPONENT
S-VIDEO
A
A
Connections
ON/OFF
ON
ON
ON
ON
ON
ON
ON
ON z1
ON
ON
ON
ON z1
ON
ON
ON
ON z1
ON
ON
ON
HDMI
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
S
S
S
S
S
S
S
S
A
A
A
A
A
A
A
S
S
S
S
S
S
S
S
Input Signals
COMPONENT
S-VIDEO
A
A
A
A
A
S
A
S
S (1080p)
A
S (1080i ~ 480p)
A
S (480i/576i)
A
S (1080p)
A
S (1080p)
A
S (1080i ~ 480p)
A
S (480i/576i)
A
S (1080p)
S
S (1080p)
S
S (1080i ~ 480p)
S
S (480i/576i)
S
S (1080p)
S
S (1080p)
S
S (1080i ~ 480p)
S
S (480i/576i)
S
A
A
A
A
A
S
A
S
S
A
S
A
S
S
S
S
A
A
A
S
A
S
S
A
S
A
S
S
S
S
A
A
A
A
A
S
A
S
S
A
S
A
S
S
S
S
Getting Started
Relationship Between Video Signals and Monitor Output
ENGLISH
Getting Started
Troubleshooting
Connections
Settings
If a problem should arise, first check the following:
1. Are the connections correct?
2. Is the set being operated as described in the owner’s manual?
3. Are the other components operating properly?
If this unit does not operate properly, check the items listed in the table below. Should the problem persist,
there may be a malfunction.
In this case, disconnect the power immediately and contact your store of purchase.
GGeneralH
Playback
Multi-Zone
Remote Control
Symptom
Set does not
operate properly.
Power does not
turn on, or turns
off directly after it
was turned on.
No sound is
produced from
speakers.
Cause
Countermeasure
•External noise or interference is •Reset the microprocessor.
causing the set to malfunction.
•Connection of the power cord is •Check the insertion of the power
faulty.
cord plug.
Information
•Connection with the input
devices or connection of the
speaker cables is faulty.
•Device you want to play and set
input source do not match.
•Master volume is turned too
low.
•Mute mode is set.
•Headphones are connected.
•No digital signals are being
input.
•Check the connections.
Troubleshooting
Specifications
•Select an appropriate input
source.
•Adjust the master volume to an
appropriate level.
•Cancel the mute mode.
•Disconnect the headphones.
•Select an input source for which
the digital input setting has been
made.
•The connectors to which the •Set the input mode.
digital inputs are assigned and
the settable input modes do not
match.
Display is off.
•The “Dimmer” setting is set to •Set to something other than
“OFF”.
“OFF”.
•The PURE DIRECT mode is set. •Set a surround mode other than
the PURE DIRECT mode.
“DOLBY DIGITAL” •Blu-ray Disc player / DVD player’s •Check the Blu-ray Disc player /
indicator does not
digital audio output setting is not DVD player’s audio output setting.
appear on display.
proper.
For details, read the Blu-ray Disc
player / DVD player’s operating
instructions.
67
Page
70
19
12
20, 42
42
46
46
37
39
35
48
–
Symptom
Power switches
off suddenly while
you are using the
AVR-2310CI, the
power indicator
will flash in red
at intervals of
approximately 2
seconds.
Power switches
off suddenly while
you are using the
AVR-2310CI, the
power indicator
will flash red
at intervals of
approximately 0.5
seconds.
Even applying
power, the power
display flashes
red at intervals of
approximately 0.5
seconds.
Set does not work
properly when
remote control
unit operated.
Cause
Countermeasure
•The protection circuit will be •Please switch off power at once,
activated depending upon the and re-apply the power after
temperature rise in the internal the body temperature has fallen
parts of the unit.
sufficiently.
•Please re-install AVR-2310CI in a
place having good ventilation.
Page
3
•Use speakers having impedance •Please use speakers which have
less than that specified.
the specified impedance.
•If speaker cable core wires touch •Unplug the power cord, then
each other or the core wires after twisting the core wires
become disconnected from their together tightly again, or effecting
terminals, the protection circuit termination treatments etc,
will be activated in the event of please reconnect once again.
core wires coming into contact
with the AVR-2310CI rear panel.
•The AVR-2310CI amplifier circuit •Switch off the power and please
has failed.
contact the DENON service
adviser.
12
•Batteries are worn.
•You are operating outside of the
specified range.
•Obstacle between main unit and
remote control unit.
•The batteries are not inserted in
the proper direction, as indicated
by the polarity marks in the
battery compartment.
•The set’s remote control sensor
is exposed to strong light (direct
sunlight, inverter type fluorescent
bulb light, etc.).
•Settings do not match the remote
control unit’s DEVICE SELECT
switch.
•Replace with new batteries.
•Operate within the specified
range.
•Remove the obstacle.
3
3
•Insert the batteries in the
proper direction, following the
polarity marks in the battery
compartment.
•Move the set to a place in which
the remote control sensor will
not be exposed to strong light.
3
•Match the settings to the remote
control unit’s DEVICE SELECT
switch.
57
–
12
–
3
3
ENGLISH
47, 48
Symptom
No picture
appears.
49
46
–
28
12
Picture cannot be
recorded.
Cause
•The connections between the
AVR-2310CI and monitor are
faulty.
•The monitor’s input setting is
wrong.
•PURE DIRECT mode is set.
•The player is connected using
the component input connectors,
the monitor is connected
using the video (yellow) output
connectors.
•Input source does not match
recorder’s video connection
connector (video).
55
–
–
39
DVDs cannot be
copied on a DVR.
–
The menu screen
and status
indicators are not
displayed.
31
•“OFF” is
status.
displayed
for
the
•The main volume display is
“OFF”.
•The display during tuner operation
is “OFF”.
•The display during iPod operation
is “OFF”.
Countermeasure
•Check the connections.
•Set properly.
•Cancel the PURE DIRECT mode.
•High definition (1080i/720p) and
progressive (480p/576p) video
signals are not down-converted.
Set the player to interlace
(480i/576i) signals.
•The video conversion function
does not work for the REC
OUT connectors. Match the
input source and recorder
connections.
•This is not a malfunction. Most
movie software includes copy
prevention signals and cannot be
copied.
•When
viewing
HDMI
or
component video signals via
the AVR-2310CI, the GUI menu
appears when the MENU button
on the main unit or the MENU
button on the main remote
control unit.
•Set “Manual Setup” – “Option
Setup” – “GUI” – “Text” to
“ON”.
•Set “Manual Setup” – “Option
Setup” – “GUI” – “Master
Volume” to “Top” or “Bottom”.
•Set when “Manual Setup”
– “GUI” – “Tuner Information” is
not “OFF”.
•Set when “Manual Setup”
– “GUI” – “ iPod Information” is
not “OFF”.
Page
13 ~ 17
–
48
–
16
–
10
34
Specifications
31
GVideoH
Troubleshooting
•The “Manual Setup” – “HDMI • Set to “TV”.
Setup” – “HDMI Audio Out”
setting is set to “Amp”.
29
–
Information
28
Page
13
–
Remote Control
•The surround back speaker’s •Check the setting and change it
power amplifier is assigned to a as necessary.
different channel.
•“S.Back” setting is set to •Set to something other than
“None”.
“None”.
•The
“Audio/Video
Adjust” •Please set “Audio/Video Adjust”
– “Audio Adjust” – “Surround – “Audio Adjust” – “Surround
Back” settings are “OFF”.
Back” to settings other than
“OFF”.
•Surround mode not set to a mode •Select a surround playback
for 6.1- or 7.1-channel playback.
mode.
•Subwoofer’s power not turned •Turn on the subwoofer’s power.
on.
•The “Subwoofer” setting at •Set to “Yes”.
“Speaker Config.” is set to “No”.
•The subwoofer is not properly •Check the connections.
connected.
•The subwoofer’s volume is •Adjust the subwoofer’s volume
turned off.
to an appropriate level.
•Blu-ray Disc player / DVD player’s •Set the Blu-ray Disc player / DVD
audio output setting is not set to player. For details, refer to the
bitstream.
Blu-ray Disc player / DVD player’s
operating instructions.
•Blu-ray Disc player / DVD player is •Use a DTS-compatible player.
not compatible with DTS sound
playback.
•The AVR-2310CI’s “Decode •Set to the “Auto” or “DTS”
Mode” setting is set to “PCM”.
mode.
•The “Manual Setup” – “HDMI •Set to “Amp”.
Setup” – “HDMI Audio Out”
setting is set to “TV”.
Cause
Countermeasure
•Connect the HDMI.
•HDMI is not connected.
•Blu-ray Disc player’s audio output •Set the Blu-ray Disc player. For
setting is not set to bitstream.
details, refer to the Blu-ray Disc
player’s operating instructions.
•Blu-ray Disc player is not •Use a DTS-compatible player.
compatible with DTS sound
playback.
Multi-Zone
HDMI audio
signals are not
output from
speakers.
No sound is
output from
the monitor
connected
with HDMI
connections.
Symptom
Dolby TrueHD,
DTS-HD, Dolby
Digital Plus audio
is not output.
Playback
DTS sound is not
output.
Page
46
Settings
No sound is
produced from
subwoofer.
Cause
Countermeasure
•You are playing a monaural source •The mode is set to something
(TV, etc.) in the “STANDARD” other than “STANDARD” (Dolby/
(Dolby/DTS Surround) mode.
DTS Surround).
•The surround mode is set to •Set to a surround playback
“STEREO”, “DIRECT” or “PURE mode.
DIRECT”.
Connections
Symptom
No sound is
produced from
center speaker.
No sound
is produced
from surround
speakers.
No sound is
produced from
surround back
speaker.
Getting Started
GAudioH
34
34
34
68
ENGLISH
Getting Started
GSIRIUS Satellite RadioH
GHDMIH
Connections
Settings
Playback
Multi-Zone
Symptom
HDMI audio
signals are not
output from
speakers.
Cause
Countermeasure
•The “Manual Setup” – “HDMI •Set to “Amp”
Setup” – “HDMI Audio Out”
setting is set to “TV”.
No picture
appears
with HDMI
connections.
•The connections to the HDMI
connectors are faulty.
•HDMI input setting is improper.
•The monitor is not compatible
with
copyright
protection
(HDCP).
•The HDMI format of the player
and monitor do not match.
•The “Manual Setup” – “HDMI
Setup” – “HDMI Audio Out”
setting is set to “Amp”.
Remote Control
Information
Troubleshooting
No sound is
output from
the monitor
connected
with HDMI
connections.
When performing •HDMI’s
CEC
the following
operating.
operations on a
connected device,
AVR-2310CI
has the same
operations.
⋅Power ON/OFF
⋅Switching audio
output devices
⋅Adjust volume
⋅Switch input
source
function
Page
31
•Check the connections.
13
•Check the HDMI input setting.
•Connect a monitor that is
compatible
with
copyright
protection (HDCP).
•Match the HDMI format of the
player and monitor.
•Set to “TV”.
37
13
is •Set “Manual Setup” – “HDMI
Setup” -– “HDMI Control” to
“OFF”.
When you only want to operate
the power on/off each device, set
“Power Off Control” to “OFF”.
13
31
31
Symptom
Specifications
69
Cause
Countermeasure
•The input source assigned to •Switch to the input source
“iPod Dock” is not selected.
assigned at “iPod Dock”.
•Cable is not properly connected. •Reconnect.
•Control dock for iPod’s AC •Plug the control dock for iPod’s
adapter is not connected to AC adapter into a power outlet.
power outlet.
”Call SIRIUS”z
is displayed.
”SUBSCRIPTION
UPDATED” is
displayed.
”Enter Lock
Code [
]” is
displayed.
Cause
Countermeasure
•The SiriusConnect Home Tuner •Check that the connections are
unit is not connected.
correct.
Page
37
15
–
Page
18
•The antenna is not connected.
•Check that the connections are
correct.
18
•The signal cannot be received.
•Reposition the antenna.
–
•Channel is not present.
•Select another channel.
–
•The signal cannot be received.
•Reposition your SiriusConnect
Home Tuner and Home Dock
antenna.
•Displays while SiriusConnect •Reposition your SiriusConnect
Home Tuner is connected.
Home Tuner and Home Dock
antenna.
•Channels are not subscribed to. •If you subscribe to the channel,
you can receive the channel.
•While
updating
contract
–
information.
•Selected channels are locked.
•Please insert pass word (4 digits)
into “[
]”.
z: After scroll displays “Call 888-539-....” twice, displays “Call SIRIUS”.
GiPodH
iPod cannot be
played.
Symptom
“CHECK SIRIUS
TUNER” is
displayed.
”ANTENNA
ERROR” is
displayed.
”NO SIGNAL” is
displayed.
”INVALID
CHANNEL” is
displayed.
”ACQUIRING
SIGNAL” is
displayed.
–
–
–
–
45
ENGLISH
[AM]
520 kHz ~ 1710 kHz
18 µV
nGeneral
Power supply:
Power consumption:
Maximum external dimensions:
Weight:
AC 120 V, 60 Hz
6.0 A
0.3 W (Standby)
434 (W) x 171 (H) x 377 (D) mm (17-3/32” x 6-47/64” x 14-27/32”)
11.3 kg (24 lbs 14.6 oz)
nMain Remote control unit (RC-1117)
Batteries:
Maximum external dimensions:
Weight:
R6/AA Type (two batteries)
52 (W) x 243 (H) x 21 (D) mm (2-3/64” x 9-9/16” x 53/64”)
184 g (Approx 6.5 oz) (including batteries)
Information
nSub Remote control unit (RC-1119)
Batteries:
Maximum external dimensions:
Weight:
R03/AAA Type (two batteries)
50 (W) x 211 (H) x 22 (D) mm (1-31/32” x 8-5/16” x 55/64”)
110 g (Approx 3.9 oz) (including batteries)
Troubleshooting
z For purposes of improvement, specifications and design are subject to change without notice.
Specifications
• Power amplifier
Front (A, B):
Rated output:
105 W+105 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)
135 W+135 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
Center:
105 W
(8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)
135 W
(6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
Surround:
105 W+105 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)
135 W+135 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
Surround Back:
105 W+105 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)
135 W+135 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
Output connectors:
Front:
A or B
6~16 Ω/ohms
A + B
12~16 Ω/ohms
Center, Surround, Surround Back / Amp Assign:
6~16 Ω/ohms
• Analog
Input sensitivity / Input impedance: 200 mV / 47 kΩ/kohms
10 Hz ~ 100 kHz — +1, –3 dB (DIRECT mode)
Frequency response:
100 dB (IHF-A weighted, DIRECT mode)
S/N:
[FM]
(note: µV at 75 Ω/ohms, 0 dBf = 1 x 10-15 W)
87.5 MHz ~ 107.9 MHz
1.0 µV (11.2 dBf)
1.6 µV (15.3 dBf)
23 µV (38.5 dBf)
77 dB
72 dB
MONO 0.15 %
STEREO 0.3 %
Remote Control
nAudio section
Y (brightness) signal — 1 Vp-p, 75 Ω/ohms
PB / CB signal — 0.7 Vp-p, 75 Ω/ohms
PR / CR signal — 0.7 Vp-p, 75 Ω/ohms
5 Hz ~ 60 MHz — +0, –3 dB (when video convert set to “OFF”)
Multi-Zone
Specifications
Y (brightness) signal — 1 Vp-p, 75 Ω/ohms
C (color) signal — 0.286 Vp-p, 75 Ω/ohms
5 Hz ~ 10 MHz — +1, –3 dB (when video convert set to “OFF”)
Playback
If in step 3 the display does not flash at intervals of about 1 second, start over from step 1.
nTuner section
Receiving Range:
Usable Sensitivity:
50 dB Quieting Sensitivity:
S/N (IHF-A):
Total harmonic Distortion (at 1 kHz):
1 Vp-p, 75 Ω/ohms
5 Hz ~ 10 MHz — +1, –3 dB
Settings
1 Turn off the power using on the main unit.
and
on the main unit.
2 Press while simultaneously pressing
the display starts flashing at intervals of about 1 second, release the two
3 Once
buttons.
• Standard video connectors
Input / output level and impedance:
Frequency response:
• S-Video connectors
Input / output level and impedance:
Frequency response:
• Color component video connector
Input / output level and impedance:
Frequency response:
Connections
Perform this procedure if the display is abnormal or if operations cannot be performed.
When the microprocessor is reset, all the settings are reset to their default values.
nVideo section
Getting Started
Restoring All the Settings to as They were at the
Time of Purchase (Resetting the Microprocessor)
70
List of preset codes / Liste de codes préréglés
Contec
Contec/Cony
Craig
Crosley
Crown
CTX
DEVICE SELECT : TV
Television
A
B
C
3M
Addison
Admiral
Advent
Adventura
Aiko
Akai
Albatron
Alleron
America Action
Ampro
Amtron
Anam
Anam National
AOC
Apex
Apex Digital
Audiovox
Aventura
Axion
Bang & Olufsen
Barco
Baur
Belcor
Bell & Howell
Benq
Blue Sky
Bradford
Brillian
Brockwood
Broksonic
byd:sign
Candle
Carnivale
Carver
CCE
Celebrity
Celera
Changhong
Ching Tai
Chun Yun
Chung Hsin
Citizen
Clarion
Coby
100
163
033, 044, 050, 141
130
041
138
018, 019, 034, 119, 137, 151
127, 131
039
139
129
038
139
035, 038
030, 036, 079, 137 151, 154
048, 062
174
038, 067, 071, 138, 139, 140
029
120
146
020
034
030
033
089, 135
020
038, 139
145
030
050, 139, 141
123
037, 041, 137, 151
137, 151
155
147, 152
034
048
048
163
157, 163, 169, 173
160, 169
037, 038, 049, 137, 138,
151, 153, 156
139
074
PRESET CODE
Curtis Mathes
D
CXC
Cytron
Daewoo
Daytron
Dell
Denon
DiamondVision
Dimensia
Disney
Dumont
Durabrand
E
Dwin
Electroband
Electrograph
Electrohome
Element
Emerson
F
G
Emprex
Envision
Epson
Erres
ESA
Ether
Firstar
Fujitsu
Funai
Furi
Futuretech
Gateway
GE
H
GFM
Gibralter
Go Video
Goldstar
Gradiente
Grundig
Grunpy
Haier
Hallmark
Hankook
Harman/Kardon
139
038
038, 139
049, 155
038, 139, 153
082
010, 019, 044, 137, 140,
143, 151, 153, 155, 156
038, 139
118
030, 036, 049, 138, 140, 153
030
012, 032
143
125
010
060
013, 030
012, 029, 050, 111, 136,
139, 141
044, 128
034
142
034, 035, 050
106
012, 029, 030, 038, 039,
049, 050, 139, 141, 153
124
137, 151
080, 097
149
018, 029
158
170
037, 039, 077
029, 038, 039, 139
165
038, 139
085, 142, 144
010, 012, 035, 040, 045,
055, 140
027, 028
013, 030, 137, 151
134
012, 030, 036, 137, 151
084
152
038, 039, 139
107, 114, 136, 148
012
158, 168, 169
155
I
J
K
L
M
Harvard
Havermy
Hello Kitty
Hewlett Packard
Hisense
Hitachi
HP
Hyundai
Ilo
IMA
Infinity
InFocus
Initial
Innova
Insignia
Janeil
JBL
JC Penney
JCB
Jean
Jinxing
JVC
Kawasho
Kaypani
KEC
Kenwood
Kioto
KLH
Kloss Novabeam
Kolin
KTV
LG
Logik
LXI
M&S
Magnasonic
Magnavox
Majestic
Marantz
Maxent
Mediator
Megapower
Megatron
Memorex
MGA
Megatron
Mintek
Mitsubishi
Monivision
038, 139
044
140
068
087, 167, 174
[014]z, 058, 103, 143, 181
031
133
090, 115, 117, 122
038
155
099
117
152
029, 108, 109, 110
041
155
010, 036, 037, 040
034
159, 163, 167, 170
161, 165, 167
023, 024, 025, 040, 050
034
154
139
030, 137, 151
020, 155
048
038, 041
166, 169
038, 137, 139, 147, 151, 153
012, 030, 036, 127, 151
033
010, 012, 155
155
049
028, 037, 047, 054, 056,
137, 151, 155
033
046, 137, 151, 152, 155
112, 142
149
127
012, 143
012, 029, 033, 036, 050, 141
012, 030, 036, 137, 151
013, 040, 153
117
012, 030, 036, 044, 057, 178
127, 131
N
O
P
Montgomery Ward
Motorola
MTC
Multitech
NAD
NEC
Netsat
Net-TV
Newave
Nikko
Norcent
Norwood Micro
Noshi
NTC
Olevia
Onwa
Oppo
Optoma
Optonica
Orion
Otto Versand
Panasonic
Penney
Philco
Philips
Q
R
Philips Magnavox
Phonola
Pilot
Pioneer
Polaroid
Portland
Prima
Princeton
Prism
Proscan
Proton
Protron
Proview
Pulsar
Pye
Quasar
Quelle
Radio Shack/
Realistic
Radiola
RadioShack
RCA
Realistic
033
035, 044
030, 036, 137, 151, 156
038, 139, 147
012, 152
030, 035, 036, 081, 137, 151
152
090, 142
163, 164, 168
012, 137, 138, 151
079, 174
090
150
138
064, 072, 078
038, 139
121
098
044
050, 141
034
007, 008, 009, 035, 040,
059, 069, 176
012, 030, 137, 150, 151,
153, 156
030, 035, 036, 037, 050,
137, 151, 155
020, 021, 022, 035, 037,
046, 066, 105, 149, 152,155
020, 046, 047
149
030, 137, 151, 153
180, 184
030, 048, 075
030, 036, 138, 153
083, 130
127
040
010
012, 154
073
086, 106
013, 030
149
035, 040
034
010, 038
149
012, 030, 137, 139, 151, 153
010, 011, 030, 035, 036,
043, 045, 150, 156
012, 030, 137, 139, 151, 153
S
Runco
Sampo
Samsung
Samsux
Sansui
Sanyo
SBR
Sceptre
Scimitsu
Scotch
Scott
Sears
SEI
Sharp
Shen Ying
Sheng Chia
Shogun
Signature
Simpson
Sinudyne
SKY
Skygiant
Sony
Soundesign
Sova
Sowa
Squareview
SSS
Starlite
Studio Experience
Superscan
Supre-Macy
Supreme
SVA
Sylvania
T
Symphonic
Synco
Syntax
Syntax-Brillian
Tacico
Tandy
Tatung
Technics
Techview
Techwood
Teco
Teknika
013, 137, 151
137, 142, 151, 153, 154
012, 018, 019, 030, 036,
101, 102, 137, 147, 151,
152, 156
153
050, 141
092
149
096
030
012
012, 030, 038, 039, 116, 139
010, 012, 029, 039, 088, 155
034
015, 016, 017, 044, 070,
153, 179, 183
163
044, 164
030
033
037
034
152
169
000, 001, 002, 034, 052,
053, 175, 182
012, 037, 038, 039, 139
073
162, 167
029
030, 038, 139
038, 139
131
044
041
034
020, 113, 148, 174
026, 027, 028, 029, 037,
063, 104, 137, 151, 155
029, 038, 139
157, 162, 163, 164, 168, 172
072
072, 088
163, 168
044
035, 090, 144, 159, 162, 167
040
132
040
159, 164, 168
030, 033, 036, 037, 038,
039, 138, 139, 153, 155, 156
Telefunken
TMK
Toshiba
U
V
W
Y
Z
Totevision
Trutech
Tuntex
TVS
US Logic
Vector Research
Vidikron
Vidtech
Viewsonic
Viking
Viore
Vizio
Wards
Westinghouse
White
Westinghouse
Yamaha
Yapshe
Zenith
019
012
003, 004, 005, 006, 030,
051, 156, 177
153
091
158, 163
050, 141
090
137, 151
155
012, 030, 036
061, 076, 142
041
115
061, 093, 094, 095, 126, 144
010, 012, 030, 033, 036,
039, 137, 151, 155
061, 065, 140
T
W
RCA
Sylvania
F
M
P
T
G
C
D
G
H
I
L
M
O
P
R
S
Akai
Apex
Axion
Coby
Cytron
DiamondVision
Disney
GFM
Haier
Ilo
Initial
Insignia
LG
Mintek
Oppo
Panasonic
Philips
Polaroid
RCA
Sansui
Sharp
Sylvania
028
059
006
Blu-ray Disc Player
D
Denon
030, 036, 137, 151
171
012, 013, 014, 030, 033,
042, 050, 138, 141
Accele Vision
Accurian
Advent
Akai
Alco
Allegro
Amphion
MediaWorks
AMW
Apex
011
026
B
C
D
E
Apple
Arrgo
Aspire
Astar
Audiovox
Axion
Bang & Olufsen
Blaupunkt
Blue Parade
BOSS
Broksonic
California Audio
Labs
Changhong
CineVision
Coby
Curtis Mathes
CyberHome
Cytron
Daewoo
Denon
Desay
DiamondVision
Disney
Durabrand
Emerson
H
121
I
DVD Player
A
049, 050, 141
119
062
120
074
118
125
060
028
114
117
117
108
030
117
121
069
066
075
010
051
070
027, 063
Magnavox
Panasonic
Toshiba
DEVICE SELECT : DVD/HDP
TV/DVD Combination
A
005, 051
065
TV/DVD/VCR Combination
TV/VCR Combination
R
S
Toshiba
Westinghouse
088
146
131
098, 126
129
142
117
117
025, 026, 027, 028, 049,
059, 136
109
043
132
090
075, 129
099
137
136
039
089
061, 126
128
071, 153
074, 142
050, 081
143
029, 043, 151, 152, 155, 156
097
057, 142
014, 070, [111]z, 112, 128
116
124, 125
053, 063
144
127, 138, 145
J
K
L
M
N
O
P
Enterprise
Epson
ESA
Fisher
Funai
Gateway
GE
GFM
Go Video
Gradiente
Greenhill
Haier
Harman/Kardon
Hitachi
Hiteker
Ilo
Initial
Insignia
Integra
Irradio
iSymphony
JBL
JVC
Kawasaki
Kenwood
KLH
Koss
Landel
Lasonic
Lenoxx
LG
Liquid Video
Liteon
Magnavox
Memorex
Microsoft
Mintek
Mitsubishi
Nesa
Next Base
Nexxtech
Onkyo
Oppo
Optoma
Oritron
Panasonic
Philips
Pioneer
Polaroid
Proceed
Proscan
138
120
145
139
145
068, 154
044, 054, 136
101
012, 142
128
136
103
082, 140
013
025
096
096, 136
055, 102, 145
039
091
108
140
030, 031, 032, 033, 034
129
080, 128
058, 129, 136
067, 134
147
141
133, 144
055, 076, 077, 095, 138, 142
134
068, 146
047, 062, 127, 135, 145
053, 126
044
096, 136
056
136
147
115
071, 135
100, 114
122
067, 134
017, 018, 019, 020, 021,
022, 023, 024, 078, 083,
084, 085, 128, 135
007, 037, 038, 047, 052,
064, 073, 104, 135
039, 040, 041, 042, 087
028, 086
025
044
Q
R
S
Protron
Qwestar
RCA
Regent
Rio
Rowa
Sampo
Samsung
Sansui
Sanyo
Sharp
Shinsonic
Sonic Blue
Sony
T
Sungale
Superscan
Sylvania
Symphonic
Teac
Technics
Theta Digital
Toshiba
U
V
W
X
Y
Z
Trutech
Urban Concepts
US Logic
Venturer
VocoStar
Westinghouse
Xbox
Yamaha
Zenith
119
067
035, 036, 039, 044, 129, 136
133
142
130
148, 150
011, 012, 013, 015, 016,
048, 128
008, 126
126, 139
051, 060, 079, 092, 093, 094
096
142
000, 001, 002, 003, 004,
005, 006 ,045, 065, 066,
105, 106, 107
113
127
046, 101, 123, 127, 145
038
129, 149, 157, 158
128
039
007, 008, 009, 010, 069,
126, 135
110
135
096
129
118
072
044
017, 128
055, 135, 138, 142
DVD/VCR Combination
B
C
G
I
P
S
T
Broksonic
CineVision
Go Video
Insignia
Panasonic
Samsung
Sony
Sylvania
Toshiba
061
074
012
055
018, 019, 020
012, 048
002, 003, 004, 005
046
007, 010
TV/DVD Combination
A
C
Akai
Apex
Audiovox
Axion
Coby
098
026
075
099
081
D
G
H
I
L
M
O
P
R
S
T
W
Cytron
DiamondVision
Disney
GFM
Haier
Ilo
Initial
Insignia
LG
Mintek
Oppo
Panasonic
Philips
Polaroid
RCA
Sansui
Sharp
Sylvania
Toshiba
Westinghouse
097
124
063
101
103
096
096
102
077
096
100
078
073
086
035
008
079
046, 123
008, 101
072
TV/DVD/VCR Combination
M
P
T
Magnavox
Panasonic
Toshiba
062
021
009
DEVICE SELECT : DVR/VCR
Digital Video Recorder
A
B
C
D
E
G
H
ABS
Alienware
Bang & Olufsen
CyberPower
Dell
035
035
079
035
035
063, 065, 066, 067, 071,
DIRECTV
073, 077
Dish Network
076
Dishpro
076
Echostar
076
Expressvu
076
Gateway
035
GOI
076
Hewlett Packard
035
HNS
072
Howard Computers 035
HP
035
HTS
076
Hughes Network
063, 065, 066, 067, 073
Systems
Humax
063
Hush
035
PRESET CODE
I
J
L
M
N
P
R
S
T
iBUYPOWER
JVC
Linksys
Media Center PC
Microsoft
Mind
Niveus Media
Northgate
Panasonic
Philips
Proscan
RCA
ReplayTV
Samsung
Sonic Blue
Sony
Stack
Systemax
Tagar Systems
Tivo
U
V
Z
Toshiba
Touch
UltimateTV
Viewsonic
Voodoo
ZT Group
035
063, 076
035
035
035
035
035
035
070
063, 065, 066, 067, 068, 072
077
063, 065, 072, 077
069
065, 067, 072
069
035, 064, 074, 078
035
035
035
063, 064, 065, 068, 073,
074, 078
035, 075
035
077
035
035
035
D
E
F
G
H
Video Cassette Recorder
A
B
C
ABS
Adventura
Aiwa
Akai
Alienware
American High
Asha
Audio Dynamics
Audiovox
Beaumark
Bell & Howell
Broksonic
Calix
Candle
Canon
CineVision
Citizen
Colortyme
Craig
Curtis Mathes
Cybernex
CyberPower
035
008, 033
008, 033
020
035
032
013, 030
018
031
013, 030
029
056
031
030, 031
032
058
030, 031
018
013, 030, 031
012, 018, 030, 032
013, 030
035
PRESET CODE
I
J
K
L
M
Daewoo
Davidson
DBX
Dell
Denon
DIRECTV
Durabrand
Dynatech
Electrohome
Electrophonic
Emerson
Fisher
Fuji
Funai
Garrard
Gateway
GE
Go Video
Goldstar
Gradiente
Harley Davidson
Harman/Kardon
Headquarter
Hewlett Packard
Hitachi
Howard Computers
HP
Hughes Network
Systems
Humax
Hush
iBUYPOWER
Insignia
Instant Replay
JC Penney
JCL
JVC
Kenwood
Kodak
LG
Linksys
Lloyd's
LXI
Magnasonic
Magnavox
Magnin
Marantz
Marta
Matsushita
Media Center PC
MEI
Memorex
019, 033
008
018
035
014
061
025
008, 033
010, 031
031
008, 010, 021, 031, 032, 033
029
026, 032
008, 021, 033
008, 033
035
012, 013, 030, 032
013, 048
018, 031
008, 033
033
018
029
035
[008]z, 014
035
035
014, 061
061
035
035
059
032
018, 029, 030, 031, 032
032
016, 017, 018, 029
018, 029
031, 032
031
035
008, 033
031
021
008, 021, 022, 025, 028, 032
013, 031
018, 029, 032
031
032
035
032
008, 013, 025, 029, 030,
031, 032, 033, 062
N
O
P
Q
R
MGA
MGN Technology
Microsoft
Mind
Minolta
Mitsubishi
Motorola
MTC
Multitech
NEC
Nikko
Niveus Media
Noblex
Northgate
Olympus
Optimus
Optonica
Orion
Panasonic
Penney
Pentax
Philco
Philips
Philips Magnavox
Pilot
Profitronic
Pulsar
Quarter
Quartz
Quasar
RadioShack
Radio Shack/
Realistic
Radix
Randex
RCA
Realistic
ReplayTV
Ricavision
Runco
S
Samsung
Sanky
Sansui
Sanyo
Scott
Sears
Sharp
Shogun
Singer
Sonic Blue
010, 013
013, 030
035
035
014
010, 038
032
008, 013, 030
008, 030, 033
018, 029
031
035
013, 030
035
032
021, 031
024
044, 062
000, 001, 002, 003, 004,
032, 060
013, 014
014
032
024, 032, 041, 061
041
031
013
025
029
029
032
008, 024, 031
024, 029, 030, 031, 032, 033
031
031
011, 012, 013 ,014, 015,
030, 032, 051
008, 024, 029, 030, 031,
032, 033
060
035
025
013, 019, 020, 030, 040,
048, 049, 061
025
008, 044, 062
013, 029, 030
010, 019
008, 014, 029, 031, 032
023, 024, 042
013, 030
032
060
Sony
Stack
STS
Sylvania
T
Symphonic
Systemax
Tagar Systems
Tandy
Tashiko
Teac
Technics
Teknika
Thomas
Tivo
TMK
Toshiba
U
V
W
X
Y
Z
Totevision
Touch
Unitech
Vector
Vector Research
Video Concepts
Videosonic
Viewsonic
Villain
Voodoo
Wards
XR-1000
Yamaha
Zenith
ZT Group
005, 006, 007, 008, 026
,034, 035, 036, 037, 045 ,
052, 053, 054
035
014, 032
008, 010, 021, 022, 032,
033, 046, 055
008, 021, 022, 033
035
035
029
031
008, 033
032
008, 031, 032, 033
008
061
013, 030
009, 010, 019, 035, 039,
047, 050, 057
013, 030, 031
035
013, 030
019
018
018, 019
013, 030
035
008
035
008, 013, 014, 024, 030,
031, 032, 033
008, 032, 033
018, 029
008, 025, 026, 027, 043
035
TV/DVD/VCR Combination
M
P
T
T
Broksonic
CineVision
Go Video
Insignia
Panasonic
Samsung
Sony
Sylvania
Toshiba
056
058
048
059
002, 003, 004
040, 048, 049
037, 045, 052, 053, 054
046
039, 050, 057
Satellite Receiver
A
C
D
E
G
H
I
J
L
M
TV/VCR Combination
R
S
RCA
Sylvania
051
055
022
001
047
DEVICE SELECT : SAT/CBL
DVD/VCR Combination
B
C
G
I
P
S
Magnavox
Panasonic
Toshiba
N
P
AccessHD
Alpha Digital
Alphastar
Artec
CaptiveWorks
Channel Master
Chaparral
Coolsat
Coship
Crossdigital
Digital Stream
109
109
083
106
102
111
077
103
114
120
110
058, 059, 060, 061, 062, 063,
064, 068, 069, 073, 074, 075,
DIRECTV
076, 088, 089, 090, 093,
095, 116
052, 053, 054, 055, 065, 091,
Dish Network
115, 119
Dishpro
115, 119
Drake
078
Echostar
052, 065, 091, 115, 119
Expressvu
119
GE
056, 057, 112
General Instrument 079, 117
GOI
119
Goodmind
112
Hisense
118
Hitachi
074, 084
HTS
119
Hughes Network
060, 062, 067, 068, 070,
Systems
075, 093
Humax
104
Ilo
118
Insignia
096
Jerrold
117
JVC
052, 065, 091, 119
Lasonic
113
LG
096, 105
Magnavox
073, 107
Memorex
073
MicroGem
108
Mitsubishi
068, 099
Motorola
117
Next Level
117
Panasonic
061, 095, 097
R
Pioneer
Primestar
Proscan
Proton
RadioShack
RCA
S
T
U
V
Z
Realistic
Samsung
Sharp
Sony
Star Choice
STS
Tivax
Tivo
Toshiba
UltimateTV
Uniden
US Digital
Viewsat
Voom
Zenith
F
G
H
J
Jerrold
L
M
B
C
D
E
ABC
Adelphia
Americast
Antronix
Archer
AT&T
Bell South
Cable Vision
Cabletenna
Cableview
Clearmaster
ClearMax
Colour Voice
Comcast
Comtronics
Contec
Coolmax
COX
Daeryung
Director
Dumont
Eastern
[009]z, 010, 012, 028, 040
007
047
014, 015
015
003
047
006
014
013
046
046
016
000, 005, 033
017
018
046
005
036
033
051
019
LG
Magnavox
MegaCable
Memorex
Motorola
N
O
P
Cable TV
A
Everquest
Focus
GC Electronics
GE
Gehua
Gemini
General Instrument
Goldstar
Hamlin
Hitachi
Jasco
Q
R
S
Movie Time
Multitech
NEC
NET Brazil
NSC
Oak
Pace
Panasonic
Paragon
Philips
Pioneer
Popular Mechanics
Proscan
Pulsar
Quasar
RadioShack
RCA
Realistic
Recoton
Regal
Regency
Rembrandt
Runco
Samsung
Scientific Atlanta
Signal
Signature
Sony
Sprucer
Standard
Component
Starcom
Stargate
Starquest
041
045
015
009, 010
033
020, 041
005, 010, 033, 044
042
021
010
041
005, 010, 020, 028, 029, 033,
041, 044
050
022
005
023, 040
000, 003, 005, 033, 037,
039, 044
024
046
011
035
024
018
008, 043
026, 027, 040
040
016, 022
002, 030, 036, 042
045
009, 010
040
040
041, 046
013, 027
015
045
021
019
010
040
008, 034, 042
001, 002, 003, 007, 012,
036, 038
020, 041
010
006, 048
027
025
020, 028, 041
020, 041
020, 041
T
U
V
Z
Supercable
Supermax
Time Warner
Tocom
Torx
Toshiba
Trans PX
Tristar
TS
Tusa
TV86
Unika
United Cable
Universal
V2
View Star
Viewmaster
Vision
Vortex View
Zenith
Zentek
044
046
004
031
049
040
044
046
049
020, 041
024
014, 015
028
014, 015
046
018, 022, 024
046
046
046
032, 040, 047
045
N
O
P
Q
R
S
DEVICE SELECT : CD
CD Player
A
B
C
D
G
H
J
K
L
L
M
Accuphase
Acoustic Research
ADS
Aiwa
Akai
Audio Alchemy
Audio Pro
Audio-Technica
B&K
California Audio
Labs
Carver
Denon
DKK
DMX Electronics
Dynamic Bass
GE
Genexxa
Harman/Kardon
JVC
Kenwood
Krell
Linn
Magnavox
Marantz
Miro
018
019
020
021
022
023
024
025
026
036
040, 041
001, 042, [111]z
035
040
041
017
037
007
003, 011, 012
038, 039
040
040
027
028
035
T
W
Y
Z
Mission
Musical Fidelity
NEC
NSM
Onkyo
Optimus
Philips
Pioneer
Polk Audio
Proscan
Proton
QED
Quad
RCA
Realistic
Rotel
SAE
Sansui
Sanyo
SAST
Sharp
Silsonic
Sonic Frontiers
Sony
Soundesign
Symphonic
TAG McLaren
Technics
Wards
Yamaha
Zonda
040
029
030
040
002
035, 037, 039, 041
009, 010
006
040
017
040
040
040
000, 017
041
040
040
040
031
040
032
038
040
004, 005, 008, 013, 014
033
034
040
015
040
016
040
DVD preset codes / Codes préréglés DVD
111
(default / default)
DVD-900
DVD-700
DVD-1000
DVD-1400
DVD-1500
DVD-1710
DVD-1720
DVD-1730
DVD-1740
DVD-1910
DVD-1920
DVD-1930
DVD-1940
DVD-2200
DVD-2800
DVD-2800g
014
DVD-2900
DVD-2910
DVD-2930
DVD-3800
DVD-3910
DVD-3930
DVD-A11
DVD-A1XV
DVD-A1
DVD-800
DVD-1600
DVD-2000
DVD-2500
DVD-3000
DVD-3300
Blu-Ray preset codes /
Codes préréglés Blu-Ray
e Model No. /
Modéle numéro
Philips
100
073
111
107
060, 067, 068, 070, 072,
073, 090
060
082
056, 057
118
117
056, 057, 058, 070, 076, 086,
087, 088, 089, 092
080
060, 062, 069, 070, 071, 094
098
059, 066, 116
117
085
109
060, 070
063
116
073, 081
118
101
117
064, 096
eM
odel No. / Modéle numéro
Pansat
Paysat
PCT
Philco
121
DVD-1800BD
DVD-2500BT
DVD-3800BD
DVD-A1UDCI
[ ]* :Preset codes set upon shipment from
the factory.
*[ ] :Les codes préréglés diffèrent en fonctiom
des livraison de l’usine.
PRESET CODE
www.denon.com
D&M Holdings Inc.
Printed in China 5411 10255 000DA
Download PDF