BCR25RM-12LB Datasheet

BCR25RM-12LB Datasheet
BCR25RM-12LB
Triac
Medium Power Use
REJ03G1715-0100
Rev.1.00
Jul 10, 2008
Features
•
•
•
•
• The product guaranteed maximum junction
temperature of 150°C
• Insulated Type
• Planar Type
IT (RMS) : 25 A
VDRM: 600 V
IFGTI, IRGTI, IRGTIII: 50 mA
Viso: 2000 V
Outline
RENESAS Package code: PRSS0003ZA-A
(Package name: TO-3PFM)
2
1. T1 Terminal
2. T2 Terminal
3. Gate Terminal
3
1
1
2
3
Applications
Contactless AC switch, electric heater control, light dimmer, on/off and speed control of small induction motor, on/off
control of copier lamp
Maximum Ratings
Parameter
Symbol
Note1
Repetitive peak off-state voltage
Note1
Non-repetitive peak off-state voltage
Notes: 1. Gate open.
REJ03G1715-0100 Rev.1.00 Jul 10, 2008
Page 1 of 7
VDRM
VDSM
Voltage class
12
600
720
Unit
V
V
BCR25RM-12LB
Symbol
Ratings
Unit
RMS on-state current
Parameter
IT (RMS)
25
A
Surge on-state current
ITSM
250
A
I2t
313
A2s
PGM
PG (AV)
VGM
IGM
Tj
Tstg
—
Viso
5
0.5
10
2
–40 to +150
–40 to +150
5.2
2000
W
W
V
A
°C
°C
g
V
I2t for fusion
Peak gate power dissipation
Average gate power dissipation
Peak gate voltage
Peak gate current
Junction Temperature
Storage temperature
Mass
Isolation voltage
Conditions
Commercial frequency, sine full wave 360°
conduction, Tc = 96°C
50 Hz sinewave 1 full cycle, peak value,
non-repetitive
Value corresponding to 1 cycle of half wave 50
Hz, surge on-state current
Typical value
Ta = 25°C, AC 1 minute,
T1·T2·G terminal to case
Electrical Characteristics
Parameter
Repetitive peak off-state current
On-state voltage
Symbol
IDRM
VTM
Min.
—
—
Typ.
—
—
Max.
3.0/5.0
1.5
Unit
mA
V
Test conditions
Tj = 125°C /150°C, VDRM applied
Tc = 25°C, ITM = 40 A,
instantaneous measurement
Gate trigger voltageNote2
Ι
ΙΙ
ΙΙΙ
VFGTΙ
VRGTΙ
VRGTΙΙΙ
—
—
—
—
—
—
2.0
2.0
2.0
V
V
V
Tj = 25°C, VD = 6 V, RL = 6 Ω,
RG = 330 Ω
Gate trigger curentNote2
Ι
ΙΙ
ΙΙΙ
IFGTΙ
IRGTΙ
IRGTΙΙΙ
—
—
—
—
—
—
50
50
50
mA
mA
mA
Tj = 25°C, VD = 6 V, RL = 6 Ω,
RG = 330 Ω
VGD
Rth (j-c)
0.2/0.1
—
—
—
—
1.7
V
°C/W
Tj = 125°C /150°C, VD = 1/2 VDRM
Junction to caseNote3
(dv/dt)c
10/1
—
—
V/µs
Tj = 125°C /150°C
Gate non-trigger voltage
Thermal resistance
Critical-rate of rise of off-state
Note4
commutation voltage
Notes: 2. Measurement using the gate trigger characteristics measurement circuit.
3. The contact thermal resistance Rth (c-f) in case of greasing is 0.5°C/W.
4. Test conditions of the critical-rate of rise of off-state commutation voltage is shown in the table below.
Test conditions
1. Junction temperature
Tj = 125/150°C
2. Rate of decay of on-state commutating current
(di/dt)c = –13 A/ms
3. Peak off-state voltage
VD = 400 V
REJ03G1715-0100 Rev.1.00 Jul 10, 2008
Page 2 of 7
Commutating voltage and current waveforms
(inductive load)
Supply Voltage
Time
Main Current
(di/dt)c
Time
Main Voltage
(dv/dt)c
Time
VD
BCR25RM-12LB
Performance Curves
Maximum On-State Characteristics
Rated Surge On-State Current
Surge On-State Current (A)
400
102
Tj = 150°C
101
Tj = 25°C
100
0.5
1.0
1.5
2.0
2.5
3.0
102
VGT = 2.0 V
PGM = 5 W
PG(AV) =
0.5 W
IGM = 2 A
100
7
5
3
2
VGD = 0.1 V
5 7103
2 3
5 7104
103
Typical Example
102
IFGT I
IRGT I
IRGT III
101
-40
0
40
80
120
160
Gate Current (mA)
Junction Temperature (°C)
Gate Trigger Voltage vs.
Junction Temperature
Maximum Transient Thermal Impedance
Characteristics (Junction to case)
103
Typical Example
102
101
-40
Gate Trigger Current (Tj = 25°C)
VGM = 10 V
× 100 (%)
Gate Trigger Current vs.
Junction Temperature
0
40
80
120
Junction Temperature (°C)
REJ03G1715-0100 Rev.1.00 Jul 10, 2008
Page 3 of 7
160
Transient Thermal Impedance (°C/W)
Gate Voltage (V)
× 100 (%)
Gate Trigger Voltage (Tj = t°C)
101
Gate Characteristics (I, II and III)
10–1
IFGT I, IRGT I, IRGT III
7
5
1
10 2 3 5 7 102 2 3
Gate Trigger Voltage (Tj = 25°C)
100
Conduction Time (Cycles at 50 Hz)
3
2
3
2
200
On-State Voltage (V)
5
101
7
5
300
0
100
3.5
Gate Trigger Current (Tj = t°C)
On-State Current (A)
103
102
2.0
103
104
100
101
1.8
1.6
1.4
1.2
1.0
0.8
0.6
1.4
1.0
0
10-1
102
Conduction Time (Cycles at 50 Hz)
BCR25RM-12LB
Allowable Case Temperature vs.
RMS On-State Current
Maximum On-State Power Dissipation
160
20
10
360° Conduction
Resistive,
inductive loads
0
10
40
80
60
40
360° Conduction
20 Resistive,
inductive loads
0
0
10
20
30
40
Allowable Ambient Temperature vs.
RMS On-State Current
Allowable Ambient Temperature vs.
RMS On-State Current
160
140
100
Curves apply regardless
of conduction angle
Resistive, inductive loads
Natural convection
80
160 160 t2.3
120
60
Ambient Temperature (°C)
All fins are blackpainted
aluminum and greased
120 120 t2.3
40
100 100 t2.3
20
10
20
30
120
100
80
60
40
20
0
1
2
3
4
5
RMS On-State Current (A)
Breakover Voltage vs.
Junction Temperature
Repetitive Peak Off-State Current vs.
Junction Temperature
Typical Example
102
0
40
80
120
Junction Temperature (°C)
REJ03G1715-0100 Rev.1.00 Jul 10, 2008
Page 4 of 7
160
× 100 (%)
RMS On-State Current (A)
103
101
-40
Natural convection
No Fins
Curves apply regardless
of conduction angle
Resistive, inductive loads
140
0
40
Repetitive Peak Off-State Current (Tj = t°C)
Ambient Temperature (°C)
30
100
RMS On-State Current (A)
0
0
× 100 (%)
20
120
RMS On-State Current (A)
160
Breakover Voltage (Tj = t°C)
Case Temperature (°C)
30
0
Breakover Voltage (Tj = 25°C)
Curves apply
regardless of
conduction angle
140
Repetitive Peak Off-State Current (Tj = 25°C)
On-State Power Dissipation (W)
40
106
Typical Example
105
104
103
102
-40
0
40
80
120
Junction Temperature (°C)
160
BCR25RM-12LB
Latching Current vs.
Junction Temperature
103
103
Latching Current (mA)
Typical Example
102
101
-40
0
40
80
120
T2+, G–
Typical
Example
Distribution
102
101
T2–, G–
Typical
Example
100
-40
160
T2+, G+
Typical
Example
0
40
80
120
160
Junction Temperature (°C)
Breakover Voltage vs.
Rate of Rise of Off-State Voltage (Tj = 125°C)
Breakover Voltage vs.
Rate of Rise of Off-State Voltage (Tj = 150°C)
160
Typical Example
Tj = 125°C
140
120
100
III Quadrant
80
60
40
I Quadrant
20
0
101
102
103
104
Breakover Voltage (dv/dt = xV/µs)
× 100 (%)
Breakover Voltage (dv/dt = 1V/µs)
Junction Temperature (°C)
160
Typical Example
Tj = 150°C
140
120
100
80
III Quadrant
60
40
I Quadrant
20
0
101
102
103
104
Rate of Rise of Off-State Voltage (V/µs)
Rate of Rise of Off-State Voltage (V/µs)
Commutation Characteristics (Tj = 125°C)
Commutation Characteristics (Tj = 150°C)
102
7
5
102
7
5
3
2
Typical Example
Tj = 125°C
IT = 4 A
τ = 500 µs
VD = 200 V
f = 3 Hz
Main Voltage
(dv/dt)c
Time
Critical Rate of Rise of Off-State
Commutating Voltage (V/µs)
Holding Current (Tj = t°C)
Critical Rate of Rise of Off-State
Commutating Voltage (V/µs)
Breakover Voltage (dv/dt = xV/µs)
× 100 (%)
Breakover Voltage (dv/dt = 1V/µs)
Holding Current (Tj = 25°C)
× 100 (%)
Holding Current vs.
Junction Temperature
VD
Main Current
IT
(di/dt)c
τ
Time
I Quadrant
101
7
5
3
2
100
7
3
III Quadrant
5 7 101
2 3
5 7 102
2
Rate of Decay of On-State
Commutating Current (A/ms)
REJ03G1715-0100 Rev.1.00 Jul 10, 2008
Page 5 of 7
3
3
2
101
7
5
3
2
Typical Example
Tj = 150°C
IT = 4 A
τ = 500 µs
VD = 200 V
f = 3 Hz
Main Voltage
(dv/dt)c
Time
VD
Main Current
IT
(di/dt)c
τ
Time
III Quadrant
I Quadrant
Minimum
Characteristics
100 Value
7
3 5 7 101
2 3
5 7 102
2
Rate of Decay of On-State
Commutating Current (A/ms)
3
BCR25RM-12LB
Gate Trigger Current (tw)
Gate Trigger Current (DC)
× 100 (%)
Gate Trigger Current vs.
Gate Current Pulse Width
103
7
5
4
3
2
Typical Example
IFGT I
IRGT III
IRGT I
102
7
5
4
3
2
101 0
10
2 3 4 5 7 101
2 3 4 5 7 102
Gate Current Pulse Width (µs)
Gate Trigger Characteristics Test Circuits
6Ω
Recommended Circuit Values Around The Triac
Load
6Ω
C1
A
6V
V
Test Procedure I
V
A
V
330Ω
Test Procedure III
REJ03G1715-0100 Rev.1.00 Jul 10, 2008
Page 6 of 7
C0
R0
330Ω
Test Procedure II
6Ω
6V
R1
A
6V
330Ω
C1 = 0.1 to 0.47µF C0 = 0.1µF
R0 = 100Ω
R1 = 47 to 100Ω
BCR25RM-12LB
Package Dimensions
Previous Code
TO-3PFM / TO-3PFMV
15.6 ± 0.3
+ 0.4
– 0.2
2.0 ± 0.3
2.7 ± 0.3
φ3.2
Unit: mm
5.5 ± 0.3
3.2 ± 0.3
4.0 ± 0.3
2.6
0.86
1.6
0.86
0.66
5.45 ± 0.5
MASS[Typ.]
5.2g
21.0 ± 0.5
RENESAS Code
PRSS0003ZA-A
5.0 ± 0.3
JEITA Package Code
SC-93
5.0 ± 0.3
19.9 ± 0.3
Package Name
TO-3PFM
+ 0.2
– 0.1
0.2
0.9 +– 0.1
5.45 ± 0.5
Order Code
Lead form
Straight type
Standard packing
Magazine (Tube)
Quantity
30
Standard order code
Type name
Note : Please confirm the specification about the shipping in detail.
REJ03G1715-0100 Rev.1.00 Jul 10, 2008
Page 7 of 7
Standard order
code example
BCR25RM-12LB
Sales Strategic Planning Div.
Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
Notes:
1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes
warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property
rights or any other rights of Renesas or any third party with respect to the information in this document.
2. Renesas shall have no liability for damages or infringement of any intellectual property or other rights arising out of the use of any information in this document, including,
but not limited to, product data, diagrams, charts, programs, algorithms, and application circuit examples.
3. You should not use the products or the technology described in this document for the purpose of military applications such as the development of weapons of mass
destruction or for the purpose of any other military use. When exporting the products or technology described herein, you should follow the applicable export control laws
and regulations, and procedures required by such laws and regulations.
4. All information included in this document such as product data, diagrams, charts, programs, algorithms, and application circuit examples, is current as of the date this
document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas products listed in this document,
please confirm the latest product information with a Renesas sales office. Also, please pay regular and careful attention to additional and different information to be
disclosed by Renesas such as that disclosed through our website. (http://www.renesas.com )
5. Renesas has used reasonable care in compiling the information included in this document, but Renesas assumes no liability whatsoever for any damages incurred as a
result of errors or omissions in the information included in this document.
6. When using or otherwise relying on the information in this document, you should evaluate the information in light of the total system before deciding about the applicability
of such information to the intended application. Renesas makes no representations, warranties or guaranties regarding the suitability of its products for any particular
application and specifically disclaims any liability arising out of the application and use of the information in this document or Renesas products.
7. With the exception of products specified by Renesas as suitable for automobile applications, Renesas products are not designed, manufactured or tested for applications
or otherwise in systems the failure or malfunction of which may cause a direct threat to human life or create a risk of human injury or which require especially high quality
and reliability such as safety systems, or equipment or systems for transportation and traffic, healthcare, combustion control, aerospace and aeronautics, nuclear power, or
undersea communication transmission. If you are considering the use of our products for such purposes, please contact a Renesas sales office beforehand. Renesas shall
have no liability for damages arising out of the uses set forth above.
8. Notwithstanding the preceding paragraph, you should not use Renesas products for the purposes listed below:
(1) artificial life support devices or systems
(2) surgical implantations
(3) healthcare intervention (e.g., excision, administration of medication, etc.)
(4) any other purposes that pose a direct threat to human life
Renesas shall have no liability for damages arising out of the uses set forth in the above and purchasers who elect to use Renesas products in any of the foregoing
applications shall indemnify and hold harmless Renesas Technology Corp., its affiliated companies and their officers, directors, and employees against any and all
damages arising out of such applications.
9. You should use the products described herein within the range specified by Renesas, especially with respect to the maximum rating, operating supply voltage range,
movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas shall have no liability for malfunctions or damages
arising out of the use of Renesas products beyond such specified ranges.
10. Although Renesas endeavors to improve the quality and reliability of its products, IC products have specific characteristics such as the occurrence of failure at a certain
rate and malfunctions under certain use conditions. Please be sure to implement safety measures to guard against the possibility of physical injury, and injury or damage
caused by fire in the event of the failure of a Renesas product, such as safety design for hardware and software including but not limited to redundancy, fire control and
malfunction prevention, appropriate treatment for aging degradation or any other applicable measures. Among others, since the evaluation of microcomputer software
alone is very difficult, please evaluate the safety of the final products or system manufactured by you.
11. In case Renesas products listed in this document are detached from the products to which the Renesas products are attached or affixed, the risk of accident such as
swallowing by infants and small children is very high. You should implement safety measures so that Renesas products may not be easily detached from your products.
Renesas shall have no liability for damages arising out of such detachment.
12. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written approval from Renesas.
13. Please contact a Renesas sales office if you have any questions regarding the information contained in this document, Renesas semiconductor products, or if you have
any other inquiries.
http://www.renesas.com
RENESAS SALES OFFICES
Refer to "http://www.renesas.com/en/network" for the latest and detailed information.
Renesas Technology America, Inc.
450 Holger Way, San Jose, CA 95134-1368, U.S.A
Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501
Renesas Technology Europe Limited
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K.
Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900
Renesas Technology (Shanghai) Co., Ltd.
Unit 204, 205, AZIACenter, No.1233 Lujiazui Ring Rd, Pudong District, Shanghai, China 200120
Tel: <86> (21) 5877-1818, Fax: <86> (21) 6887-7858/7898
Renesas Technology Hong Kong Ltd.
7th Floor, North Tower, World Finance Centre, Harbour City, Canton Road, Tsimshatsui, Kowloon, Hong Kong
Tel: <852> 2265-6688, Fax: <852> 2377-3473
Renesas Technology Taiwan Co., Ltd.
10th Floor, No.99, Fushing North Road, Taipei, Taiwan
Tel: <886> (2) 2715-2888, Fax: <886> (2) 3518-3399
Renesas Technology Singapore Pte. Ltd.
1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632
Tel: <65> 6213-0200, Fax: <65> 6278-8001
Renesas Technology Korea Co., Ltd.
Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea
Tel: <82> (2) 796-3115, Fax: <82> (2) 796-2145
Renesas Technology Malaysia Sdn. Bhd
Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia
Tel: <603> 7955-9390, Fax: <603> 7955-9510
© 2008. Renesas Technology Corp., All rights reserved. Printed in Japan.
Colophon .7.2
To our customers,
Old Company Name in Catalogs and Other Documents
On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology
Corporation, and Renesas Electronics Corporation took over all the business of both
companies. Therefore, although the old company name remains in this document, it is a valid
Renesas Electronics document. We appreciate your understanding.
Renesas Electronics website: http://www.renesas.com
April 1st, 2010
Renesas Electronics Corporation
Issued by: Renesas Electronics Corporation (http://www.renesas.com)
Send any inquiries to http://www.renesas.com/inquiry.
Notice
1.
2.
3.
4.
5.
6.
7.
All information included in this document is current as of the date this document is issued. Such information, however, is
subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please
confirm the latest product information with a Renesas Electronics sales office. Also, please pay regular and careful attention to
additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website.
Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights
of third parties by or arising from the use of Renesas Electronics products or technical information described in this document.
No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights
of Renesas Electronics or others.
You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part.
Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of
semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software,
and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by
you or third parties arising from the use of these circuits, software, or information.
When exporting the products or technology described in this document, you should comply with the applicable export control
laws and regulations and follow the procedures required by such laws and regulations. You should not use Renesas
Electronics products or the technology described in this document for any purpose relating to military applications or use by
the military, including but not limited to the development of weapons of mass destruction. Renesas Electronics products and
technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited
under any applicable domestic or foreign laws or regulations.
Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics
does not warrant that such information is error free. Renesas Electronics assumes no liability whatsoever for any damages
incurred by you resulting from errors in or omissions from the information included herein.
Renesas Electronics products are classified according to the following three quality grades: “Standard”, “High Quality”, and
“Specific”. The recommended applications for each Renesas Electronics product depends on the product’s quality grade, as
indicated below. You must check the quality grade of each Renesas Electronics product before using it in a particular
application. You may not use any Renesas Electronics product for any application categorized as “Specific” without the prior
written consent of Renesas Electronics. Further, you may not use any Renesas Electronics product for any application for
which it is not intended without the prior written consent of Renesas Electronics. Renesas Electronics shall not be in any way
liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an
application categorized as “Specific” or for which the product is not intended where you have failed to obtain the prior written
consent of Renesas Electronics. The quality grade of each Renesas Electronics product is “Standard” unless otherwise
expressly specified in a Renesas Electronics data sheets or data books, etc.
“Standard”:
8.
9.
10.
11.
12.
Computers; office equipment; communications equipment; test and measurement equipment; audio and visual
equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots.
“High Quality”: Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anticrime systems; safety equipment; and medical equipment not specifically designed for life support.
“Specific”:
Aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or
systems for life support (e.g. artificial life support devices or systems), surgical implantations, or healthcare
intervention (e.g. excision, etc.), and any other applications or purposes that pose a direct threat to human life.
You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics,
especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation
characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or
damages arising out of the use of Renesas Electronics products beyond such specified ranges.
Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have
specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further,
Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to
guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a
Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire
control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because
the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system
manufactured by you.
Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental
compatibility of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable
laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS
Directive. Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with
applicable laws and regulations.
This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of Renesas
Electronics.
Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this
document or Renesas Electronics products, or if you have any other inquiries.
(Note 1) “Renesas Electronics” as used in this document means Renesas Electronics Corporation and also includes its majorityowned subsidiaries.
(Note 2) “Renesas Electronics product(s)” means any product developed or manufactured by or for Renesas Electronics.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement