Epson 755c - PowerLite XGA LCD Projector Specifications
advertisement
Assistant Bot
Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.
Projector Parts
Card slot
Focus ring
Exhaust air vent
Foot adjust lever
I/R receiver
Security lock port
Lens cap
Audio port
USB port
(Type B)
Video port
S-Video port
Computer/
Component
Video port USB port
(Type A)
Rear adjustable foot
Power inlet
Zoom ring
Speaker
Control panel
Specifications
General
Type of display
Resolution
(native format)
Poly-silicon TFT active matrix
1024 × 768 pixels (XGA)
Color reproduction
Brightness
24-bit, 16.8 million colors
PowerLite 755c 2000 lumens (High Brightness mode)
1500 lumens (Low Brightness mode)
PowerLite 765c 2500 lumens (High Brightness mode)
2000 lumens (Low Brightness mode)
Epson PowerLite 755c/765c Projector
Contrast ratio
Image size
(diagonal)
Projection distance
Projection methods
Internal sound system
Optical aspect ratio
Zoom ratio
Noise level
400:1
30 to 300 inches (0.8 to 7.6 meters)
3.2 to 39.7 feet (1.0 to 12.1 meters)
Front, rear, upside-down (ceiling mount)
1 W monaural
4:3 (horizontal:vertical)
Keystone correction
Mouse compatibility
1:1.2
35 dB in Low Brightness mode,
40 dB in High Brightness mode
Automatic (manual adjustment capability
±30° vertical keystone correction)
Supports USB (type B)
Projection Lamp
Type UHE (Ultra High Efficiency) consumption
Lamp life
Part number
High Brightness mode: about 2000 hours
Low Brightness Mode: about 3000 hours
V13H010L32
Remote Control
Range
Batteries (2)
20 feet (6 meters)
Alkaline AAA
Dimensions
Height
Width
Depth
Weight
2.7 inches (70 mm), feet retracted
10.9 inches (276 mm)
7.6 inches (193 mm)
3.9 lb (1.8 kg)
Electrical
Rated frequency 50/60 Hz AC
Power supply 100 to 120 VAC, 2.7 A
200 to 240 VAC, 1.1 A consumption Standby: 4 W (Network off);
35 W (Network on)
8/05 Epson PowerLite 755c/765c Projector - 1
Epson PowerLite 755c/765c Projector
Environmental
Temperature Operating: 41 to 95 °F (5 to 35 °C)
Storage: 14 to 140 °F (–10 to 60 °C)
Humidity Operating: 20 to 80% RH,
(non-condensing) Storage: 10 to 90% RH
Operating altitude Up to 7,500 feet (2,286 meters)
Safety and Approvals
United States
Canada
CE Marking
FCC 47CFR Part15B Class B (DoC)
UL60950 Third Edition
ICES-003 Class B
CSA C22.2 No. 60950
Directive 73/23/EEC, 89/336/EEC
IEC 60950 Third Edition
EN 55022, EN 55024
Pixelworks™ DNX™ ICs are used in this projector.
Compatible Video Formats
The projector supports the video display formats listed below:
Mode
NTSC
NTSC 4:43
PAL
N—PAL
M—PAL
PAL—60
SECAM
HDTV (720p)
HDTV (720p)
HDTV (1080i)
HDTV (1080i)
SDTV (480p)
SDTV (480p)
TV480i
TV480i
60
50
60
50
60
50
60
50
Refresh Rate (Hz)
60
60
50
50
60
60
50
Compatible Computer Display Formats
To project images from a computer, set the computer’s video card at a refresh rate (vertical frequency) compatible with the projector; see the following table for compatible formats. Some images are automatically resized to display in the projector’s
“native” format (XGA). The frequencies of some computers may not allow images to display correctly; see your computer’s documentation for details.
SXGA1—70
SXGA1—75
SXGA1—85
SXGA2—60
SXGA2—75
SXGA2—85
SXGA3—60
SXGA3—75
SXGA3—85
SXGA+60
SXGA+75
SXGA+85
UXGA—60 iMAC VGA iMAC SVGA iMAC XGA
MAC13
MAC16
MAC19—60
MAC19
MAC21
Mode
VGA EGA
VGA—60
VESA—72
VESA—75
VESA—85
SVGA—56
SVGA—60
SVGA—72
SVGA—75
SVGA—85
XGA—60
XGA—70
XGA—75
XGA—85
75
59
75
75
117
95
75
67
Refresh Rate (Hz) Resolution
70
60
72
75
85
56
60
72
75
85
60
70
75
85
70
75
85
60
75
85
60
75
85
60
75
85
60
640
640
640
640
640
×
350*
×
480*
×
480*
×
480*
×
480*
800
800
800
800
800
×
600*
×
600*
×
600*
×
600*
×
600*
1024
×
768
1024
×
768
1024
×
768
1024
×
768
1152
×
864*
1152
×
864*
1152
×
864*
1280
×
960*
1280
×
960*
1280
×
960*
1280
×
1024*
1280
×
1024*
1280
×
1024*
1400
×
1050*
1400
×
1050*
1400
×
1050*
1600
×
1200*
640
800
×
480*
×
600*
1024
×
768
640
832
×
480*
×
624*
1024
×
768
1024
×
768
1152
×
870*
* The image is resized using Epson’s SizeWise™ Technology.
2 - Epson PowerLite 755c/765c Projector 8/05
Epson PowerLite 755c/765c Projector
Positioning the Projector
Before connecting the projector, you need to decide where to place it. The location you choose depends on the size of the room and what you are projecting.
❏ Place the projector on a sturdy, level surface, between
3.2 and 39.7 feet from the screen.
❏ Make sure there is plenty of space for ventilation around and under the projector. Do not set the projector on top of anything that could block the vents under the projector.
❏ Make sure the projector is within 6 feet of an electrical outlet or extension cord and within 5 feet of your computer and/or video source, unless you are projecting wirelessly or from a memory card.
❏ Place the projector directly in front of the center of the screen, facing the screen squarely. Otherwise, your image will not be rectangular.
Note:
It’s easier to position the projector when the screen is directly in front of the room.
Use the figure below as a guideline to help you determine how far from the screen to place the projector. Image size generally increases with distance, but may vary depending on how you position the zoom ring and whether you have adjusted the image size with other settings.
If you place the projector below the level of the screen, you’ll have to tilt it up by extending the adjustable front foot, as shown below. This may cause the image to lose its rectangular
shape, but you can correct the distortion. (See page 6 for
detailed information about correcting the image shape.)
If you place the projector level with the bottom of the screen, the image will be rectangular and you won’t have to adjust it. If you place the projector higher than the bottom of the screen, the image will still be rectangular, but you won’t be able to fill the whole screen with the image.
33.1 to 39.7 feet 6.6 to 7.9 feet 3.2 to 3.9 feet
To calculate exact measurements, use the following formulas:
❏ To find the projection distance when you know the screen’s diagonal dimension:
Wide (inches) = ((33.696 × diagonal screen size [inches]) –
21.717) / 25.4
Tele (inches) = ((40.453 × diagonal screen size [inches]) –
22.52) / 25.4
❏ To find how large a screen’s diagonal dimension will be when you know the projection distance:
Wide (inches) = (Projection distance [inches] × 0.0254 +
0.02171) / 0.033696
Tele (inches) = (Projection distance [inches] × 0.0254 +
0.02252) / 0.040453
Starting Up the Projector
Make sure your projector and other equipment are set up and connected correctly. Then turn on your projector, as described below.
If you turn on your connected computer or video equipment before starting the projector, the projector automatically detects and displays the image source. If you turn on the projector first, or have multiple pieces of connected equipment, you may have
to select the image source manually. See “Selecting the Image
Follow these steps to plug in and turn on the projector:
1. Remove the lens cap.
Caution:
Do not use the projector with the lens cap in place. The heat generated by the lamp can damage the cap.
2. Connect one end of the power cord to the projector’s power inlet. Then connect the other end to an electrical outlet.
The Power light on top of the projector turns orange, indicating that the projector is in standby mode.
8/05 Epson PowerLite 755c/765c Projector - 3
Epson PowerLite 755c/765c Projector
3. Press the P Power button on top of the projector or on the remote control.
Power button
Projector Remote control
The projector beeps once and the Power light flashes green as the projector warms up, then an image begins to appear.
When the Power light stops flashing and remains green, the projector is ready for use.
Warning:
Never look into the lens when the lamp is on. This can damage your eyes, and is especially dangerous for children.
❏ If you’ve connected a Windows ®
-based computer to the projector, you may see a New Hardware Wizard saying your computer has found a plug-and-play monitor; if so, click Cancel .
❏ If you don’t see the image you want, press the Source
Search button on the projector or the Search button on the remote control until you see the image you want to project.
❏ If you are prompted to enter a password, see “Starting the
Projector with a Password” on page 10.
Note:
You can also use the Source buttons on the remote control to switch between devices connected to the ports identified on each
button. For details, see page 5.
If a projected image fails to appear, see “You Can’t Project an
When you’re done with your presentation, shut down the
projector as described on page 7. Shutting down the projector
correctly prevents premature lamp failure and possible damage from overheating.
You Can’t Project an Image
If you don’t see the image you are trying to project, try the following:
❏ Make sure the cables are connected correctly.
❏ Make sure the Power light is green and not flashing and the lens cap is off.
❏ If you’ve connected more than one computer and/or video source, you may need to press the Source Search button on the projector’s control panel or Search button on the remote control to select the correct source. (Allow a few seconds for the projector to sync up after pressing the button.)
❏ If you’re using a PC notebook, see below.
The Projector and Notebook Don’t
Display the Same Image
If you’re projecting from a notebook, and you can’t see your image on the projection screen and on your computer at the same time, follow these guidelines.
If you’re using a PC notebook:
❏ On most systems, there’s a function key that lets you toggle between the LCD screen and the projector, or display on both at the same time. It may be labeled CRT/LCD or have an icon such as . You may have to hold down the Fn key while pressing it. Allow a few seconds for the projector to sync up after changing the setting.
❏ If the function key doesn’t permit you to display simultaneously on both screens, you should check your monitor settings to make sure both the LCD screen and the external monitor port are enabled.
From the Control Panel, open the Display utility. In the
Display Properties dialog box, click the Settings tab, then click Advanced . The method for adjusting the settings varies by brand; you may need to click a Monitor tab, then make sure the external Monitor port is set as your primary display and/or enabled. See your computer’s documentation or online help for details.
4 - Epson PowerLite 755c/765c Projector 8/05
Epson PowerLite 755c/765c Projector
If you’re using a Macintosh
®
with OS X:
You may need to set up your system to display on the projector screen as well as the LCD screen. Follow these steps:
1. From the Apple
®
menu, select System Preferences , then click Displays .
2. Select VGA Display or Color LCD , click Arrange or
Arrangement , and make sure Mirror Displays is checked.
If you’re using a Macintosh with OS 8.6 to 9.x:
You may need to set up your system to display on the projector screen as well as the LCD screen. Follow these steps:
1. From the Apple menu, select Control Panels , then click
Monitors or Monitors and Sound .
2. Click the Arrange icon.
3. Drag one monitor icon on top of the other.
If the Arrange option isn’t available, try selecting one of the
Simulscan resolution settings. Click the Monitor icon, if necessary, and then select a Simulscan resolution. (Allow a few seconds for the projector to sync up after making the selection.)
Adjusting the Image
Once you see your image, you may need to make certain adjustments, as described in this section.
Focusing and Zooming Your Image
Rotate the focus ring to sharpen the image.
Focus ring
Rotate the zoom ring to reduce or enlarge the image.
Zoom ring
Selecting the Image Source
If multiple devices are connected to the projector, the easiest way to select the image source is to press the Search button on the remote control or the Source Search button on the projector until the correct image is projected.
You can also press one of the following Source buttons on the remote control:
❏
Computer to select the device connected to the projector’s
Computer/Component Video port.
❏
S-Video to select the device connected to the
S-Video port.
❏
Video to select the device connected to the
Video port.
❏
EasyMP to project wirelessly or from a memory card.
After you select a source, the screen goes dark for a moment before the image appears.
You can also change the image size by moving the projector closer to or farther away from the screen. You can use the
E-Zoom buttons on the remote control to zoom in on a portion
of the image. See “Zooming Your Image” on page 8 for
instructions.
Adjusting the Height of Your Image
If the image is too low, you can raise it by extending the projector’s front foot.
1. Stand behind the projector. Press up on the blue foot release lever and lift the front of the projector to extend the foot.
8/05
2. Once the image is positioned where you want it, release the lever to lock the foot in position.
Epson PowerLite 755c/765c Projector - 5
Epson PowerLite 755c/765c Projector
3. If the projector is not level, rotate the foot at the back of the projector.
If the image is no longer rectangular after raising it, see the next section.
Using Keystone Correction
To adjust your image when it is wider on the top or bottom, do one of the following:
❏ Press one of the two triangular buttons on the projector’s control panel, as shown below. Continue pressing the button until you are satisfied with the shape of the image.
Correcting Computer Images
If you’ve connected a computer and the image doesn’t look right, or it doesn’t fit properly on the screen, press the Auto button on the remote control or the Enter button on the projector. This automatically resets the projector’s tracking, sync, resolution, and position settings. (You must be projecting an image for this button to have any effect.)
Note:
If the Auto Setup option in the Signal menu is set to OFF , the
Auto function will not work.
Adjusting the Image Shape
The projector automatically corrects images that are distorted when the projector is tilted up or down (up to 30°). The
Keystone window appears on the screen while the projector makes the correction.
Projector tilted up Corrected image Projector tilted down
If the projected image still isn’t rectangular, try the following:
❏ If your image looks like or , you’ve placed the projector off to one side of the screen, at an angle. Move it directly in front of the center of the screen, facing the screen squarely.
❏ If your image looks like or , you may need to manually adjust the keystone correction value. Follow the instructions below.
❏ Or press the Menu button on the remote control or projector, select the Setting menu, and press Enter . From the Setting menu, select Keystone and press Enter . Use the pointer button on the remote control to adjust the keystone setting as needed. The keystone setting is adjustable from –65 to +65. These numbers represent a range of –30° to +30° of angle change; adjustments are made in steps of
0.5°.
After correction, your image will be slightly smaller.
Note:
If the image becomes uneven, try decreasing the Sharpness setting in the Image menu.
Resizing Video images
You can use the Resize button on the remote control to adjust how an image fits into the display area.
For video images, press Resize to switch the aspect ratio between 4:3 and 16:9. This lets you play certain digital video images or movies recorded on certain DVDs in 16:9 widescreen format.
6 - Epson PowerLite 755c/765c Projector 8/05
For computer images, resizing is normally unnecessary, since the projector automatically resizes the image to make the best use of the display area. If you press the Resize button on the projector or remote control, the projector displays the image at the output resolution of the computer (which makes the image larger or smaller, depending on its resolution). If the resolution of the image is the same as the projector’s (1024 × 768), pressing Resize has no effect.
Epson PowerLite 755c/765c Projector
Adjusting the Brightness
The brightness of an image depends on the source you are projecting and the amount of light in the room. If the image is too bright or not bright enough, do one of the following:
❏ Change the Brightness setting in the Image menu.
❏ Select Low or High for the Brightness Control option in the Setting menu. Low Brightness mode extends the life of the lamp and decreases the fan noise.
Adjusting the Color Mode
You may want to adjust the color mode to select a setting that is appropriate for the image you’re projecting and the environment in which you’re projecting it. The following table lists the available color modes.
Color mode Description sRGB
Dynamic
For matching the color palette of standard sRGB computer displays.
For increased brightness in bright rooms (the default for non-computer display).
Presentation
Theater
Living Room
Blackboard
For computer presentations (the default when projecting from a computer with analog video).
For optimizing movie images with increased contrast.
For increased brightness when playing video games or watching TV in a bright room.
For projecting accurate colors on a green chalkboard (adjusts the white point).
To change the color mode, press the Color Mode button on the remote control repeatedly until you see the mode you want.
The currently selected setting appears in the upper right corner of the screen. You can also use the projector menu system to select the Color Mode setting in the Image menu.
Sleep Mode
You can set the projector to automatically turn off the lamp and enter “sleep mode” when it has not received any signals for
30 minutes. This conserves electricity, cools the projector, and extends the life of the lamp. If you want to start projecting again, press the P Power button. If you are done using the projector, unplug the power cord.
You can enable sleep mode in the Extended menu under
Operation . (Sleep mode is off by default.)
Using Direct Power On
The Direct Power On function enables faster setup. The projector starts up automatically when you plug it in; you won’t have to press the P Power button.
Follow these steps to enable Direct Power On:
1. Press the Menu button on the remote control and select the
Extended menu.
2. Choose Operation and press Enter .
3. Choose Direct Power On and press Enter .
4. Highlight ON and press Enter .
5. Press Esc or Menu to exit.
Note:
When Direct Power On is enabled, shut down the projector as you normally would. Follow the instructions in the next section. (The projector will start automatically when power is restored after a power failure if it is plugged in.)
Shutting Down the Projector
When you’ve finished using the projector, follow the recommended procedure to shut it down. This extends the lamp life and protects the projector from possible overheating.
1. Turn off any equipment plugged into the projector.
2. To turn off the projector, press the P Power button on the projector or remote control. You see a confirmation message.
(If you don’t want to turn it off, press any other button.)
3. Press the P Power button again. The lamp is turned off.
When the projector beeps twice, it’s safe to unplug it.
(If the projector is mounted on the ceiling, you’ll need to wait 10 seconds for the projector to cool down before you can unplug the power cord.)
If you want to turn the projector on again, make sure the
Power light is not flashing. Then press the P Power button.
Caution:
To avoid damaging the projector or lamp, never unplug the power cord when the Power light is green or flashing orange.
8/05 Epson PowerLite 755c/765c Projector - 7
Epson PowerLite 755c/765c Projector
4. If necessary, press the blue foot release lever and lower the projector to retract the front foot, as shown.
5. Replace the lens cap and unplug the power cord.
Using the Remote Control
When using the remote control, stand within 20 feet of the projector. Point the remote control either at the projector or at the screen (the projector’s front sensor can detect signals bounced off the screen). Press the button for the function you want to use.
Controlling the Volume
To change the volume, press the or button on the remote control or projector.
You can also adjust the volume using the projector’s Setting menu.
Turning Off the Picture and Sound
You can use the A/V Mute button on the remote control to turn off the image and sound. This is useful if you want to temporarily redirect your audience’s attention.
❏ To turn off the picture and sound, press the
A/V Mute button. The screen turns blue (or black) or displays a logo image (if one has been defined and enabled).
❏ To turn the image and sound back on, press the A/V Mute button again.
You can create an image, such as a company logo or a picture, to display on the screen whenever you press the A/V Mute button.
See the User’s Guide for more information.
Stopping Action
Press the Freeze button to stop the action in your video or computer image and keep the current image on the screen. The sound will continue.
To restart the action, press the Freeze button again.
Zooming Your Image
Follow these steps to zoom in on a portion of the image:
1. Press the E-Zoom button on the remote control. You see a crosshair indicating the center of the zoom-in area.
2. Use the pointer button to position the crosshair in the area you want to enlarge.
3. Continue pressing the E-Zoom button to enlarge the selected area up to 4 times. While the image is enlarged, you can:
❏ Use the pointer button to move around the screen.
❏ Press the E-Zoom button to zoom out.
4. When you’re done, press the Esc button to return the image to its original size.
Using the Remote Control as a Wireless
Mouse
When you use the remote control as a wireless mouse, you can control your computer or click through slide show-style presentations (such as Microsoft
®
PowerPoint
®
) from up to
20 feet away. To control your computer with the remote, make sure you have connected the USB mouse cable between the projector and your computer.
Page up or page down
Move the pointer
Left-click or double-click
Display the pointer
Right-click
❏ To advance slides in a PowerPoint presentation in Slide
Show mode, press the Page Up button on the remote control. Press the Page Down button to go back a slide.
❏ To display the mouse pointer, press the
Pointer button.
❏ To move the pointer on the screen, aim the remote at the screen and use the pointer button.
❏ To click (or left-click), press the
Enter button.
❏ To right-click, press the
Esc button.
❏ To double-click, press the
Enter button twice.
❏ To click and drag, press and hold the
Enter button and use the pointer button to move the pointer, then release the
Enter button.
8 - Epson PowerLite 755c/765c Projector 8/05
Epson PowerLite 755c/765c Projector
Replacing the Batteries
Caution:
When replacing batteries, take the following precautions:
❏ Replace the batteries as soon as they run out. If a battery leaks, wipe away battery fluid with a soft cloth. If fluid gets on your hands, wash them immediately.
❏ Do not expose batteries to heat or flame.
❏ Dispose of used batteries according to local regulations.
❏ Remove the batteries if you won’t be using the projector for a long time.
Follow these steps to replace the AAA alkaline batteries:
1. Press in the tab to remove the battery cover.
2. Remove the old batteries, then insert the new ones as shown.
Using Password Protection
If you assign a password for the projector, a screen appears requesting the password whenever you plug in and turn on the projector. If you enter the password incorrectly three times in succession, the projector’s operation is locked. Disconnect the projector from the power source and reconnect it. If you enter the incorrect password 30 times in a row, the projector is locked and remains locked until an authorized Epson servicer can unlock it.
You can also create a user’s logo for the projector, to be displayed as the startup screen and/or AV/Mute screen.
Unauthorized users cannot turn it off or change it. This discourages theft and provides a way to identify the projector should it be stolen.
Additionally, to make sure a borrowed projector is returned, you can temporarily disable the password for a set period of time. When that time has elapsed, the password function is reactivated and you must enter the password before you can use the projector.
Note:
If you should happen to enable the password before you set one, enter the default password 0000 when prompted.
If you lose the remote control, you will not be able to enter the password; so keep the remote control in a safe place at all times.
Setting a Password
1. Press the Freeze button on the remote control for about
5 seconds, until you see the Password Protect menu:
3. Replace the battery cover. (It should snap into place.)
If a password has already been set, you see the Password
Protect Release screen. See “Starting the Projector with a
2. Set Power ON Protect to ON and press Enter .
3. Press Esc .
4. Select Password and press Enter . You see the message
Change the password?
5. Select Yes and press Enter .
8/05 Epson PowerLite 755c/765c Projector - 9
Epson PowerLite 755c/765c Projector
6. Hold down the Num button on the remote control and use the numeric keypad to enter a 4-digit password.
The password will be displayed as **** . After you enter the last digit, a confirmation screen appears.
Enter the password again.
7. After you finish setting the password, press the Menu button to exit.
8. Press the Num button to deactivate the numeric keypad.
Numeric keypad Num button
Make a note of the password and keep it in a safe place.
Turning On the Password and User’s Logo
To enable the password (and User’s Logo, if one has been created), follow these steps:
1. Press the Freeze button on the remote control for about
5 seconds until you see the Password Protect menu.
2. Select Power ON Protect and press Enter .
3. Select ON and press Esc .
After turning on this feature, you have to unplug the projector (not just turn it off) in order to activate it. The password prompt appears only after plugging in the projector and turning it on.
4. If you want to disable the password temporarily so someone can use the projector without entering the password, select
Timer and press Enter . Then hold down the Num button while you use the numeric keypad to enter the number of hours (from 0 to 9999) you want the password feature disabled. If you want the projector to request the password every time it is turned on, set the timer to 0H .
The timer starts counting as soon as you close the Password
Protect menu. (You can check the elapsed time in this menu next to Time elapsed .)
When the period defined in the Time-elapsed setting has passed, and the password is entered correctly, the elapsed time is reset to 0H and the timer starts again. Remember to disable or change this setting when you’re finished using it.
5. To enable your User’s Logo, select User’s Logo Protect and press Enter . Then select ON and press Enter .
When this feature is on, the logo image appears when the projector is turned on (if the Startup Screen is enabled in the Extended menu) and as the A/V Mute screen (if you selected Logo as the Background Color in the Extended menu).
Note:
None of the User’s Logo features can be changed when the User’s
Logo Protect function is enabled.
6. Press Menu to close the Password Protect menu.
Starting the Projector with a Password
Note:
You must unplug the projector and then plug it back in to enable password protection.
When the password function is enabled, you see this screen when you plug in and turn on the projector:
Hold down the Num button on the remote control as you use the numeric keypad buttons to enter the password. Once you have entered the password correctly, the password screen closes, and projection begins.
If the password is not correct, you see the message Wrong password. Please try again . If you enter an incorrect password three times in succession, you see the message The projector’s operation will be locked. Request code xxxxx and the projector switches to standby mode for approximately
5 minutes. Write down the request code. Then disconnect the projector’s power cord from the electrical outlet, reconnect it, and turn the projector back on. When you see the Password
Protect Release screen, enter the correct password.
If you have forgotten the password, contact Epson for assistance and give them the request code number that appears in the
Password Protect Release screen.
If you enter an incorrect password 30 times in a row, the projector remains locked and you must contact an authorized
Epson servicer to unlock it.
10 - Epson PowerLite 755c/765c Projector 8/05
Epson PowerLite 755c/765c Projector
Disabling the Projector’s Buttons
When you enable the Operation Lock function, all the projector’s buttons are disabled except the P Power button.
This is useful, for example, if you want to prevent students in a classroom from playing with the projector.
1. Press the Menu button.
2. Select the Setting menu and press Enter .
3. Select Operation Lock and press Enter .
4. Select ON and press Enter . Then select Yes and press Enter to confirm the setting.
5. Press the Menu button to exit the menu system.
Note:
You can cancel Operation Lock by pressing the projector’s Enter button for 7 seconds.
4. Once the card is inserted, you see one of these screens, depending on the currently selected mode:
Ad Hoc mode
Access Point mode
Presenting Over a Wireless Network
Using EMP NS Connection, you can project images shown on your computer screen directly to your audience without connecting the projector to your computer. Before you begin, make sure you’ve installed EMP NS Connection from the
CD-ROM that came with your projector. See the User’s Guide for installation instructions.
Starting EasyMP
Before you can connect to the projector wirelessly, you have to switch it to EasyMP mode.
1. Turn on the remote control and the projector.
2. Press the EasyMP button on the remote control to select
EasyMP as the source.
3. Insert the Epson 802.11g/b card in the projector’s card slot.
Make sure the label side is facing up.
Note:
Only the Epson 802.11g/b card is guaranteed to work. Other cards may not be compatible. Replacement cards are available only through an Epson authorized servicer.
5. If you’ve already configured the projector for your wireless
network, go to “Projecting Wirelessly” on page 15.
Otherwise, continue with the next section.
Configuring the Connection
You must configure both the projector and your computer’s network settings to project wirelessly.
You can configure the projector for either of the following modes:
Ad hoc mode (computer to computer): Lets you connect just one computer at a time; you need a computer with a wireless
(802.11g or 802.11b) network card or adapter, or a Macintosh
Access point mode (infrastructure): Lets multiple computers access the projector, or trade off control of the projector; you need a wireless (802.11g or 802.11b) access point or an AirPort
(or AirPort Extreme) base station, and one or more computers with wireless network cards or adapters.
1. Switch the projector to EasyMP mode and insert the Epson
802.11 g/b card.
2. When you see the EasyMP screen, press the Enter button on the remote control to select Config .
3. Use the pointer button to highlight Basic under
Wireless LAN , then press Enter .
8/05 Epson PowerLite 755c/765c Projector - 11
Epson PowerLite 755c/765c Projector
4. Select either point mode .
Easy connect mode
You see one of these screens:
(for ad hoc) or Access
Ad hoc mode
Access point mode
5. Make sure the projector has a unique name so you can identify it when connecting to it from your computer.
Use the pointer button on the remote control to highlight the Projector Name text box, then press Enter .
The text box turns yellow to indicate you’re in input mode.
Press the pointer button up to select individual letters in alphabetical order, or down to select letters in reverse order.
Then press the pointer button to the right to move to the next character position. When you’re done typing the new name, press Enter .
To enter numbers, press and hold the Num button on the remote control while pressing number buttons on the numeric keypad. Press the Num button again to exit numeric keypad mode. When you’re done, press Enter .
6. Select the appropriate settings for your mode, described in the following table.
ESSID Ad hoc: Enter an ESSID in the ESSID textbox.
Access point: Enter an ESSID, which is the SSID name of your access point or the name of your AirPort network. (The name of your AirPort network may be different from that of your AirPort base station; select your base station in the
AirPort Admin utility and click Configure to check the name of your network.)
Password for WEB control
Projector keyword
DHCP (access point mode only)
Note that the ESSID is case-sensitive.
If you want to create a password for an internal web page, you can enter up to
8 alphanumeric characters.
Turn this option on if you want to set up a security keyword so that only people in the same room as the projector can access it. When you connect to the projector wirelessly, it displays a fourdigit randomized keyword on the screen that you need to enter when prompted.
If your access point assigns IP addresses automatically, turn this option on. Otherwise, turn it off and assign an IP address, subnet mask, and gateway address manually.
IP address (access point mode only)
Subnet mask (access point mode only)
Enter a subnet mask formatted like other subnet masks on your network.
Gateway address
(access point mode only)
Enter the IP address you want to assign the projector. It must be formatted like other addresses on the network; usually the first three sections match the access point’s IP address. The last section should be unique.
Enter the IP address that was assigned to your access point or AirPort base station when it was set up. If you don’t
know the address, see “Checking the
Gateway (Access Point’s) IP Address” on page 14.
7. When you’re done making settings, highlight the OK button at the top of the screen. Then press Enter . Highlight the OK button again and press Enter to return to the main EasyMP
Network Screen.
12 - Epson PowerLite 755c/765c Projector 8/05
Epson PowerLite 755c/765c Projector
Configuring the Network Settings for Windows
Before connecting to the projector wirelessly, make sure your computer is configured correctly. Also, make sure that the
Internet Connection Firewall is disabled. (See your Windows online help system for details.)
Note:
Depending on your computer’s wireless network adapter card, the dialog boxes you see may be different than those shown in this section.
1. Access your wireless network Properties window. For example, in Windows XP click Start > Control Panel >
Network and Internet Connections . Then double-click the Network Connections icon. You see a screen similar to this:
3. Click the Configure button. Then click the Advanced tab on the screen that appears. You see a screen like this:
Right-click and select Properties
2. Right-click the Wireless Network Connection icon and select Properties . You see a screen like this:
Click here
4. Ad hoc mode: Highlight Network Type in the Property list and set the Value to 802.11 Ad Hoc .
Access point mode: Highlight Network Type and set the
Value to Infrastructure .
5. Ad hoc mode: Highlight SSID and set the Value to match the name you gave the projector’s ESSID (for example,
CONF ROOM ).
Access point mode: Highlight SSID and set the Value to match the name assigned to the access point.
Note:
The SSID is case-sensitive.
6. Highlight Encryption and make sure it is disabled.
7. Click the General tab and make sure the network card or wireless network device is enabled.
8. Ad hoc mode: Click OK to close the network card’s
properties dialog box. Then go to “Projecting Wirelessly” on page 15.
8/05 Epson PowerLite 755c/765c Projector - 13
Epson PowerLite 755c/765c Projector
Access point mode: On the General tab, select
Protocol screen:
Internet
, then click the Properties button. You see this
9. If your access point uses DHCP, select Obtain IP address automatically . Otherwise, select Use the following IP address and enter the required information.
❏ IP address : Type in the IP address you want to assign to the computer. It must be formatted like other addresses on the network; usually the first three sections
(XXX.XXX.XXX) match the access point’s IP address, and the last section is unique.
❏ Subnet mask : For example, 255.255.255.000, but this too must match how your network is set up.
❏ Default gateway : Enter the IP address that was assigned to the access point when it was set up.
10.When done, click OK .
11.Click the Wireless Networks tab. You see this screen:
Note:
If you don’t see this tab, you may need to enable your wireless card or network device by clicking Configure to access the device settings; then follow any instructions on the screen to enable the device.
12.Verify that you’ve enabled your computer’s connection to the access point. It should be listed as shown above, with the small icon next to it, indicating a connection.
If it’s not listed, click Configure and then type the name of your access point.
13.When you’re done, click OK
Checking the Gateway (Access Point’s) IP Address
If you’re entering IP addresses manually in access point mode and need to find out the gateway IP address (the IP address of your access point), make sure the wireless connection to the access point is currently active, as described in the previous section.
Note:
If you can’t identify the gateway address using this Windows utility, use the administrator’s utility software that came with your access point.
1. Access your wireless network Properties window. For example, in Windows XP click Start > Control Panel >
Network and Internet Connections . Then double-click the Network Connections icon.
2. Right-click the Wireless Network Connection icon and select Status . Then click the Support tab.
The gateway’s (access point’s) IP address is listed as shown:
Gateway address
14 - Epson PowerLite 755c/765c Projector 8/05
Epson PowerLite 755c/765c Projector
Configuring the Network Settings for Macintosh
Your AirPort software is automatically configured to allow your
Macintosh to detect both computer-to-computer (ad hoc) and access point networks.
Typically you only need to select your projector’s ESSID (ad hoc) or your AirPort network name (access point) on the
Macintosh menu bar. If you’re having problems connecting to the projector, follow these steps:
1. From the Apple pull-down menu, select System
Preferences and click the Network icon. You see the
Network settings menu.
8. Click the AirPort icon on the menu bar at the top of the
Macintosh desktop. You see the AirPort status menu:
Select Automatic
Select Network Port
Configurations then select AirPort
2. Make sure Location is set to Automatic and select Network
Port Configurations in the Show pull-down menu.
3. Under Port Configurations, select AirPort .
4. Click Apply Now and close the window.
5. Ad hoc mode: Go to step 8.
Access point mode: Start the AirPort Admin utility. Select your base station, then click Configure .
6. On the AirPort tab, make sure your AirPort network name matches your projector’s ESSID. If not, enter the projector’s
ESSID in the AirPort Network text box and click Update .
7. If you turned DHCP in your projector’s Advanced menu, click the Network tab and make sure the Distribute IP addresses checkbox is selected. If you need to select it, click
Update .
Check to make sure AirPort is turned on.
9. Select your projector’s ESSID (ad hoc) or the name of your
AirPort network (access point).
Projecting Wirelessly
Once you’ve started EasyMP and set up your projector and computer in either ad hoc mode or access point mode, follow the steps below to start NS Connection and project wirelessly.
Note:
You must have installed EMP NS Connection from your projector
CD-ROM. See the User’s Guide for installation instructions.
1. Make sure you’ve inserted the Epson 802.11g/b card in the
projector’s card slot (see page 11).
2. Windows: Select EMP NS Connection from the Windows
Start menu.
Macintosh OS X: Double-click the EMP NS Connection icon in your Applications folder.
The first time you start NS Connection, you see a dialog box asking you to select your network. Select the name for your computer’s wireless network adapter card and click OK .
8/05 Epson PowerLite 755c/765c Projector - 15
Epson PowerLite 755c/765c Projector
Note:
If you don’t see your network adapter’s IP address, allow a minute for it to appear. If your access point or AirPort base station uses DHCP, sometimes it takes a minute for the server to pick up the IP address.
Once you’ve selected the IP address for your network adapter, you won’t see the Switch network dialog box when you start
NS Connection. If you want to change to a different network adapter, click Extension on the EMP NS Connection dialog box, then click Switch LAN .
You see the screen below. (If you have previously started
NS Connection, this is the first screen you see.)
If the connection is working properly, you see your projector listed. If you have additional Epson projectors on the network, they are also listed, along with their status. The color of the status icon next to each projector’s name indicates its status:
❏ Gray: the projector is not connected
❏ Orange: the projector is connected to another computer
❏ Green: the projector is connected to your computer
Note:
If a projector is in use and is “locked,” you won’t be able to select it.
3. If you don’t see your projector, check the following:
❏ Make sure your wireless signal is strong enough to establish a connection. If you have a Macintosh, check the AirPort icon on the Macintosh menu bar. For
Windows, see the documentation for your access point or computer network card.
❏ Make sure you’re trying to connect to the right network.
In Windows, verify that you’ve enabled your computer’s connection to the access point or that your wireless card or adapter is enabled, and that its SSID matches the projector’s ESSID. In Macintosh, check the AirPort status menu (click the AirPort icon on your menu bar) to make sure AirPort is turned on and the projector’s ESSID or your AirPort network is selected. Remember that the
ESSID is case-sensitive.
❏ Make sure you aren’t projecting one of the EasyMP configuration screens. (You should see a message that the projector is ready to connect.) If you have to exit the configuration screen, restart NS Connection.
❏ Make sure the ESSID for your projector matches the
SSID for your wireless card, adapter, or access point. If you have an AirPort base station, make sure the projector’s ESSID matches the AirPort network name.
Remember that the ESSID is case-sensitive.
Note:
The AirPort network name may be different than the
AirPort base station name. To check the network name, start the AirPort Admin utility, select your base station, and click
Configure . Then click Show All Settings . The network name appears on the AirPort tab.
❏ Check the IP address for both your projector and your wireless card, adapter, access point, or AirPort base station. The first three sections of the IP address should be identical. The last section of the projector’s IP address should be close, but not identical, to the last section of the IP address for your wireless interface, access point, or base station.
❏ Restart your computer and start NS Connection again.
❏ If you still don’t see your projector and you are using access point mode, follow the instructions in
“Connecting in IP Connect Mode” on page 17 to
connect to the projector manually.
❏ Make sure you have disabled any firewall software.
4. Once the name of your projector appears, select it and click
Connect . If more than one projector is listed, you can select up to four additional projectors and connect to them at the same time. If the selected projector is being used by another person, you can still connect to it; doing so automatically disconnects the other user.
5. If you are prompted for a keyword, enter the four-digit number displayed on the EasyMP Network screen and click OK .
16 - Epson PowerLite 755c/765c Projector 8/05
Epson PowerLite 755c/765c Projector
6. Once the connection is established, you see your computer’s image transmitted to the projection screen, and a floating control bar on your screen:
Windows
Macintosh
8. When you’re done with your presentation, click Disconnect on the control bar.
Connecting in IP Connect Mode
Even if your projector and computer are on different subnets
(access point mode only) or connecting over different routers, you can establish a connection manually using IP Connect
Mode.
1. Start NS Connection on the computer to which you want to connect. You see this screen:
If necessary, you can drag the control bar out of the way on your screen.
7. From the control bar, you can access these NS Connection features:
Provides help for NS Connection.
Locks the projector while it is in use and prevents anyone else from connecting to it (Windows only)
Limits projection to PowerPoint presentations only
(Windows only)
Lists projectors and specifies which ones are in use.
Lets you access the projector’s menu system from an
HTML browser window.
Lets you keep the projected image on screen, even if the image on your computer changes.
Turns off the image and sound.
Lets you zoom in on a part of your image.
Lets you change the brightness, contrast, and color mode.
Lets you switch between the Video, and S-Video ports.
Lets you switch between the computer and EasyMP.
2. Click the Extension button. You see this screen:
Click here
8/05 Epson PowerLite 755c/765c Projector - 17
Epson PowerLite 755c/765c Projector
3. Click Use IP connect mode , then click OK . You see this screen:
Click here
4. Click IP connection . You see this screen:
Enter the IP address and click Search
If the search fails to find a projector with the specified IP address, the searching icon turns into a question mark.
If this happens, run EasyMP to check the projector’s IP address, then repeat this step.
Note:
If you still don’t see the projector, make sure the Internet connection firewall is disabled.
6. Click the projector you want to connect to, then click the
Connect button. If more than one projector is listed, you can select additional projectors and connect to them at the same time.
7. If you are prompted for a keyword, enter the four-digit number displayed on the EasyMP Network screen and click OK .
The computer’s image is transmitted to the projector and appears on the screen.
Removing the Wireless 802.11G/B Card
Follow these steps to remove the card from your projector:
1. If you’re running NS Connection, click Disconnect on the control bar.
Click here
5. Enter the projector’s IP address and click Search .
The IP address is shown in the Projector list and a searching icon appears.
2. Check the card access light to make sure it isn’t flashing.
Caution:
Never remove the card while the card access light is green or flashing. You may damage the card or lose data.
3. Press the eject button. The button pops out.
Eject button
Access light
This icon appears if the search fails to find the projector
18 - Epson PowerLite 755c/765c Projector 8/05
4. Press the eject button again. The wireless card partially ejects.
5. Pull the card straight out. Then press the eject button back in to prevent it from being damaged.
Epson PowerLite 755c/765c Projector
Managing Projectors from a Remote
Computer
The software included with your projector lets you monitor and control projector(s) from a remote computer. These features are intended for use by network administrators.
❏ Use EMP Monitor (Windows only) to see your projectors’ status, switch image sources, and control basic settings.
❏ Use the mail notification function to receive e-mail alerts about possible problems.
❏ Use a network management utility running SNMP, such as
HP OpenView,
™
to manage your facility’s equipment from a pre-existing system.
You can also use NS Connection to register up to 16 projectors as a group. This allows you to provide quick and easy access to these projectors from other computers.
Make sure you have installed the EMP Monitor software
(included on the projector’s CD-ROM) on the computer you want to use to monitor your projectors. (See the User’s Guide for instructions.)
Note:
Your computer must be running Microsoft Windows XP, 2000, Me or 98SE.
Opening and Closing EMP Monitor
To start EMP Monitor, click Start > Programs or All
Programs > EPSON Projector > EMP Monitor .
If you’ve added the program to the Startup programs folder, it may already be open. If so, click the icon in the system tray on the lower-right corner of your screen to display the EMP
Monitor window:
Registering Projectors in EMP Monitor
Before you can monitor a projector, you have to register it.
Follow these steps:
1. Open EMP Monitor. You see this screen:
Click here
2. Click Register projector . You see this screen:
Click here
3. Click Auto detect to locate projectors currently operating on the network. Or click Manual registration and enter the projector’s name and network address.
Note:
If Auto detect fails to find the projector, your projector may not be connected or configured correctly for the network.
Any projectors found on the network are listed:
Click here
Click here to start EMP Monitor
To close EMP Monitor, right-click the program icon shown above, then select Exit .
4. Select each projector you want to add by clicking its name and clicking Add . When you’re done, click Close .
8/05 Epson PowerLite 755c/765c Projector - 19
Epson PowerLite 755c/765c Projector
You see this screen listing all registered projectors:
Note: To delete a projector from the list, highlight the projector name, and click Delete .
5. Click Close . You see the status of each of your registered projectors on the main EMP Monitor screen:
Monitoring Your Projectors
The EMP Monitor screen lets you monitor your projectors using the Status, Video Source, and Error icons shown below.
These let you see which projectors are currently being used, from which source (or port) they are projecting an image, and if a problem occurs.
The following tables explain the status, video source, and error icons. (Additional unsupported icons also appear.)
Status icons
(green) Projecting; no problems
(dark) Turned off; no problems
(green)
(dark)
Projecting; problems detected
Turned off; problems detected
Network error (for example, not connected to network or power cable disconnected).
You may also see this error if Network OFF is selected in Standby Mode.
Video source icons
Computer/Component 1
Computer/Component 2
S-Video
Video
EasyMP
Error icons
Status icon Video Source icon Error icon
Note: To monitor a projector when it’s in standby mode (plugged in but not projecting), you must first select Network ON as the
Standby Mode setting in the projector’s Extended menu.
For detailed status information, select the projector and click
View details .
Lamp replacement notification (the lamp is
nearing the end of its life; see page 23)
High-speed cooling in progress (the projector is getting too hot but continues to operate)
Overheating (projection turned off automatically)
Lamp out or lamp cover open
Fan error
Sensor error
Internal problem
20 - Epson PowerLite 755c/765c Projector 8/05
Controlling Your Projectors
The control buttons in the upper-right of the EMP Monitor screen let you turn the projectors on and off and select video signals. (Hold the mouse pointer over a button to see a description of its meaning.) Select the projector you want to operate (with the mouse pointer) before clicking one of the buttons.
Control buttons
Epson PowerLite 755c/765c Projector
Configuring the Monitoring Interval
You can select how often EMP Monitor checks the projector status:
1. From the Tool menu, select Configuration . You see this screen.
If you need the most current status information about your projectors, click the Refresh button.
The following table explains the control button functions.
Control buttons
Turns the projector on
Turns the projector off
Changes the video signal to the Computer/
Component 1 port
Changes the video signal to the Computer/
Component 2 port
Changes the video signal to the S-Video port
Changes the video signal to the Video port
Switches the display to EasyMP
Note:
To turn on a projector when it’s in standby mode (plugged in but not projecting), first select Network ON as the Standby Mode setting in the projector’s Extended menu.
Note:
If you want EMP Monitor to run whenever you start your computer, click Add to Startup .
2. Select the desired update interval and click OK .
Understanding the Notification Messages
If a projector experiences a problem, it can send an e-mail message to each of the addresses you provided using EMP
NetworkManager. The message includes the heading “Epson
Projector” in the subject line. The body of the message contains the name of the projector, the projector’s IP address, and a description of the problem. The problem descriptions are similar to the errors reported by EMP Monitor listed on
If a plus (+) sign appears before the description, it indicates that a problem has occurred. A minus (–) sign appears when the problem is resolved.
Note:
If a projector develops a critical problem, it may not be possible for it to report the error.
8/05 Epson PowerLite 755c/765c Projector - 21
Epson PowerLite 755c/765c Projector
Projector Status Lights
The lights on top of the projector indicate the projector’s status and let you know when a problem occurs.
Power light
Lamp light
Power light
Flashing red
Lamp light
Off
Orange Off
Temp light
Flashing orange
Description
Rapid cooling is in progress.
Although this is not an abnormal condition, projection will stop automatically if the temperature rises higher. Make sure there is plenty of space around and under the projector for ventilation, and that the air filters and vents are clear.
mode. You can unplug it or press the P Power button to turn it on.
Temperature light
Power light
Flashing green
Green
Flashing orange
Red
Red
Red
Red
Red
Lamp light
Off
Off
Off
Flashing red
Off
Flashing red
Flashing orange
Off
Temp light
Off
Off
Off
Flashing red
Flashing red
Off
Off
Red
Description
The projector is warming up. Wait for the image to appear.
The projector is operating normally.
The projector is cooling down.
Wait for the light to stop flashing and remain orange before unplugging it.
There is an internal error in the projector. Turn off the projector and unplug it. Contact Epson for help.
There is a problem with the fan or a sensor. Turn off the projector and unplug it. Contact Epson for help.
The lamp is burned out, broken, or not installed correctly, or the lamp cover is open. Close the cover or replace or reseat the lamp, if necessary, as described on
Replace the lamp with a new one
as soon as possible. See page 23
for instructions. If you continue to use the lamp, there is a risk it may break.
The projector has overheated and turned itself off. Let it cool for about five minutes, then turn it back on. Make sure there is plenty of space around and under the projector for ventilation. Also clean the air filter and air exhaust vents.
If it continues to overheat, you may need to replace the air filter.
Cleaning the Lens
Clean the lens whenever you notice dirt or dust on the surface.
❏ Use a canister of compressed air to remove dust.
❏ To remove dirt or smears on the lens, use lens-cleaning paper. If necessary, moisten a soft cloth with lens cleaner and gently wipe the lens.
Caution:
Do not use glass cleaner to clean the lens and do not spray liquid of any kind directly on the lens. Spray the cleaner on a soft cloth and then gently wipe the lens with the cloth.
Cleaning the Projector Case
Before you clean the case, turn off the projector and unplug the power cord.
❏ To remove dirt or dust, wipe the case with a soft, dry, lint-free cloth.
❏ To remove stubborn dirt or stains, wipe the case with a soft cloth moistened with a mild detergent.
Caution:
Do not use wax, alcohol, benzene, paint thinner, or other chemical detergents. These can damage the case.
22 - Epson PowerLite 755c/765c Projector 8/05
Epson PowerLite 755c/765c Projector
Cleaning and Replacing the Air Filter
Clean the air filter and air vents on the bottom of the projector after every 100 hours of use. If not cleaned periodically, they can become clogged with dust, preventing proper ventilation.
This can cause overheating and damage the projector.
1. Turn off the projector, allow it to cool down, and unplug the power cord.
2. Turn the projector upside down.
Use a small vacuum cleaner designed for computers and other office equipment. If you don’t have one, use a very soft brush (such as an artist’s brush).
If dirt is difficult to remove or the filter is torn, replace it.
The air filter set (part number V13H134A08 ) contains two
filters. See “Optional Accessories” on page 25 for ordering
information.
3. If you need to replace the filter, slide it off as shown.
Replacing the Lamp
The projection lamp typically lasts for about 2000 hours of use
(in High Brightness mode) or 3000 hours (in Low Brightness mode). It is time to replace the lamp when:
❏ The projected image gets darker or starts to deteriorate.
❏ The lamp light is flashing orange.
❏ The message Replace the Lamp appears on the screen when the lamp comes on. To maintain brightness and image quality, replace the lamp as soon as possible.
See page 25 for ordering information and request part number
V13H010L32 .
Note:
You can check how many hours the lamp has been used in the Info menu.
Caution:
Turn the projector off when not in use. Continuous use may reduce the life of the product.
Follow these steps to replace the lamp:
1. Press the P Power button twice to turn off the projector.
When the Power light stops flashing, unplug the power cord.
2. If the projector has been on, allow it to cool down for at least an hour (or until the lamp is cool).
Warning:
Let the lamp cool before replacing it. In the unlikely event that the lamp has broken, small glass fragments may be present and should be removed carefully to avoid injury.
3. Turn the projector over. Press in on the tabs and lift up the lamp cover.
4. Slide the new air filter until it clicks in place.
8/05 Epson PowerLite 755c/765c Projector - 23
Epson PowerLite 755c/765c Projector
4. Loosen the two screws holding the lamp in place (you don’t need to remove them).
Resetting the Lamp Timer
You must reset the lamp timer after replacing the lamp to clear the Replace the Lamp message.
Note:
Do not reset the lamp timer if you have not replaced the lamp. If you do, the Lamp Hours will not accurately reflect the number of hours that the lamp has been used.
1. Connect the power cable and turn on the projector.
2. Press the Menu button on the remote control and select the
Reset menu. Then press Enter . You see this screen:
5. Hold the lamp as shown and pull it straight out.
3. Select Lamp-Hours Reset and press Enter . You see this prompt:
Caution:
Do not touch the glass portion of the lamp assembly. Touching the glass could result in premature lamp failure.
6. Gently insert the new lamp. (If it doesn’t fit easily, make sure it is facing the right way.)
Note:
The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding proper disposal or recycling. Do not place in the trash.
7. Once the lamp is fully inserted, tighten its screws.
8. Insert the two cover tabs, then press down on the cover until it snaps into place.
9. Reset the lamp timer as described in the next section.
4. Select Yes and press Enter .
5. Press Esc to return to the Reset menu or the Menu button to exit the menu system.
24 - Epson PowerLite 755c/765c Projector 8/05
Optional Accessories
Epson provides the following optional accessories for the projectors:
Product
Replacement lamp
Air filter set (includes 2 filters)
Samsonite
®
wheeled soft case
ATA molded hard-shell carrying case
Notebook/projector soft shoulder bag
Component video cable (VGA-to-RCA)
S-Video cable
Macintosh adapter set
Distribution amplifier
50-inch portable screen
60-inch portable pop-up screen
80-inch portable pop-up screen
83.6-inch hanging pull-down screen
High resolution document imager
Kensington
®
security lock
Universal ceiling mount
False ceiling plate
Security bracket/cabling for gyro lock mounts
Adjustable ceiling channel
Part number
V13H010L32
V13H134A08
ELPKS35-S
ELPKS42
ELPKS43
ELPKC19
ELPSV01
ELPAP01
ELPDA01
ELPSC06
ELPSC07
ELPSC08
ELPSC09
V12H162020
ELPSL01
ELPMBUNI
ELPMBFCP
ELPMBSEC
ELPMBACC
You can purchase these accessories from an Epson authorized reseller. For product information and to find the nearest reseller, please call (800) GO-EPSON (800-463-7766).
To purchase online, visit www.epsonstore.com (U.S. sales only). In Canada, please call 800-463-7766 for reseller referral.
Related Documentation
CPD-20250
CPD-20251
Epson PowerLite 755c/765c User’s Guide
Epson PowerLite 755c/765c Quick Setup
Epson PowerLite 755c/765c Projector
8/05 Epson PowerLite 755c/765c Projector - 25
advertisement
Related manuals
advertisement
Table of contents
- 1 Projector Parts
- 1 Specifications
- 1 General
- 1 Projection Lamp
- 1 Remote Control
- 1 Dimensions
- 1 Electrical
- 2 Environmental
- 2 Safety and Approvals
- 2 Compatible Video Formats
- 2 Compatible Computer Display Formats
- 3 Positioning the Projector
- 3 Starting Up the Projector
- 4 You Can’t Project an Image
- 4 The Projector and Notebook Don’t Display the Same Image
- 5 Selecting the Image Source
- 5 Adjusting the Image
- 5 Focusing and Zooming Your Image
- 5 Adjusting the Height of Your Image
- 6 Correcting Computer Images
- 6 Adjusting the Image Shape
- 6 Resizing Video images
- 7 Adjusting the Brightness
- 7 Adjusting the Color Mode
- 7 Sleep Mode
- 7 Using Direct Power On
- 7 Shutting Down the Projector
- 8 Using the Remote Control
- 8 Controlling the Volume
- 8 Turning Off the Picture and Sound
- 8 Stopping Action
- 8 Zooming Your Image
- 8 Using the Remote Control as a Wireless Mouse
- 9 Replacing the Batteries
- 9 Using Password Protection
- 9 Setting a Password
- 10 Turning On the Password and User’s Logo
- 10 Starting the Projector with a Password
- 11 Disabling the Projector’s Buttons
- 11 Presenting Over a Wireless Network
- 11 Starting EasyMP
- 11 Configuring the Connection
- 15 Projecting Wirelessly
- 18 Removing the Wireless 802.11G/B Card
- 19 Managing Projectors from a Remote Computer
- 19 Opening and Closing EMP Monitor
- 19 Registering Projectors in EMP Monitor
- 20 Monitoring Your Projectors
- 21 Controlling Your Projectors
- 21 Configuring the Monitoring Interval
- 21 Understanding the Notification Messages
- 22 Projector Status Lights
- 22 Cleaning the Lens
- 22 Cleaning the Projector Case
- 23 Cleaning and Replacing the Air Filter
- 23 Replacing the Lamp
- 24 Resetting the Lamp Timer
- 25 Optional Accessories
- 25 Related Documentation