Aiwa | TV-S1311 | User`s guide | Aiwa TV-S1311 User`s guide

Color Television Users Guide
For Model:
AV-32S565
Illustration of AV-32S565 and RM-C1257G
Important Note:
In the spaces below, enter the model and serial number of your television (located
at the rear of the television cabinet). Staple your sales receipt or invoice to the
inside cover of this guide. Keep this user’s guide in a convenient place for future
reference. Keep the carton and original packaging for future use.
Model Number:
Serial Number:
AV-32S565 1
LCT1639-001A-A
0504TNH-II-IM
5/11/04, 10:34:08 AM
Important Safety Precautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: To reduce the risk of electric shock. Do not
remove cover (or back). No user serviceable
parts inside. Refer servicing to qualified service
personnel.
The lightning flash with arrowhead symbol, within an
equilateral triangle is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS TV
SET TO RAIN OR MOISTURE.
CAUTION:
TO INSURE PERSONAL SAFETY, OBSERVE THE FOLLOWING RULES
REGARDING THE USE OF THIS UNIT.
1. Operate only from the power source specified on the unit.
2. Avoid damaging the AC plug and power cord.
3. Avoid Improper installation and never position the unit where good ventilation is unattainable.
4. Do not allow objects or liquid into the cabinet openings.
5. In the event of trouble, unplug the unit and call a service technician. Do not attempt to repair
it yourself or remove the rear cover.
Changes or modifications not approved by JVC could void the warranty.
* When you don’t use this TV set for a long period of time, be sure to disconnect both the
power plug from the AC outlet and antenna for your safety.
* To prevent electric shock do not use this polarized plug with an extension cord, receptacle or
other outlet unless the blades can be fully inserted to prevent blade exposure.
IMPORTANT RECYCLING INFORMATION
This product utilizes both a Cathode Ray Tube (CRT) and other components that
contain lead. Disposal of these materials may be regulated in your community due to
environmental considerations. For disposal or recycling information, please contact
your local authorities, or the Electronic Industries Alliance: http://www.eiae.org
2
AV-32S565 2
5/11/04, 10:34:10 AM
• As an “ENERGY STAR®” partner,
JVC has determined that this
product or product model meets the
“ENERGY STAR®” guidelines for energy
efficiency.
Important Safeguards
CAUTION:
Please read and retain for your safety.
Electrical energy can perform many useful functions. This TV set has been engineered and
manufactured to assure your personal safety. But improper use can result in potential
electrical shock or fire hazards. In order not to defeat the safeguards incorporated in this
TV set, observe the following basic rules for its installation, use and servicing. Also follow all
warnings and instructions marked on your TV set.
INSTALLATION
1 Your TV set is equipped with a polarized AC line plug (one
blade of the plug is wider than the other). This safety feature
allows the plug to fit into the power outlet only one way.
Should you be unable to insert the plug fully into the outlet,
try reversing the plug. Should it still fail to fit, contact your
electrician.
(POLARIZED-TYPE)
2 Operate the TV set only from a power source as indicated on the TV set or refer to the
operating instructions for this information. If you are not sure of the type of power supply to
your home, consult your TV set dealer or local power company. For battery operation, refer
to the operating instructions.
3 Overloaded AC outlets and extension cords are dangerous, and so are frayed power cords
and broken plugs. They may result in a shock or fire hazard. Call your service technician for
replacement.
4 Do not allow anything to rest on or roll over the power cord, and do not place the TV set
where power cord is subject to traffic or abuse. This may result in a shock or fire hazard.
5 Do not use this TV set near water — for example, near a bathtub, washbowl, kitchen sink, or
laundry tub, in a wet basement, or near swimming pool, etc.
6 If an outside antenna is connected to the TV set, be sure the antenna system is grounded
so as to provide some protection against voltage surges and built-up static charges.
Section 810 of the National Electrical Code provides information with respect to proper
grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors, location of antenna discharge unit, connection
requirements for the grounding electrode.
3
AV-32S565 3
5/11/04, 10:34:11 AM
7 An outside antenna system should not be located in the vicinity of overhead power lines
or other electric light or power circuits, or where it can fall into such power lines or circuits.
When installing an outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be fatal.
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRICAL
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC - NATIONAL ELECTRIC CODE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ARTICLE 250, PART H)
8 TV sets are provided with ventilation openings in the cabinet to allow heat generated during
operation to be released.
Therefore:
— Never block the bottom ventilation slots of a portable TV set by placing it on a bed, sofa,
rug, etc.
— Never place a TV set in a “built-in” enclosure unless proper ventilation is provided.
— Never cover the openings with a cloth or other material.
— Never place the TV set near or over a radiator or heat register.
9 To avoid personal injury:
— Do not place a TV set on a sloping shelf unless properly secured.
— Use only a cart or stand recommended by the TV set manufacturer.
— Do not try to roll a cart with small casters across thresholds or deep pile carpets.
— Wall or shelf mounting should follow the manufacturer’s instructions, and should use a
mounting kit approved by the manufacturer.
Use
10 Caution children about dropping or pushing objects into the TV set through cabinet
openings. Some internal parts carry hazardous voltages and contact can result in a fire or
electrical shock.
11 Unplug the TV set from the wall outlet before cleaning. Do not use liquid or an aerosol
cleaner.
12 Never add accessories to a TV set that has not been designed for this purpose. Such
additions may result in a hazard.
4
AV-32S565 4
5/11/04, 10:34:11 AM
PORTABLE CART WARNING
(Symbol provided by RETAC)
13 For added protection of the TV set during a lightning storm or when the TV set is to be left
unattended for an extended period of time, unplug it from the wall outlet and disconnect the
antenna. This will prevent damage to product due to lightning storms or power line surges.
14 A TV set and cart combination should be moved with care. Quick stops, excessive force,
and uneven surfaces may cause the TV set and cart combination to overturn.
Service
15 Unplug this TV set from the wall outlet and refer servicing to qualified service personnel
under the following conditions:
A. When the power cord or plug is damaged or frayed.
B. If liquid has been spilled into the TV set.
C. If the TV set has been exposed to rain or water.
D. If the TV set does not operate normally by following the operating instructions. Adjust
only those controls that are covered in the operating instructions as improper adjustment
of other controls may result in damage and will often require extensive work by a
qualified technician to restore the TV set to normal operation.
E. If the TV set has been dropped or damaged in any way.
F. When the TV set exhibits a distinct change in performance — this indicates a need for
service.
16 Do not attempt to service this TV set yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
17 When replacement parts are required, have the service technician verify in writing that the
replacement parts he uses have the same safety characteristics as the original parts. Use
of manufacturer’s specified replacement parts can prevent fire, shock, or other hazards.
18 Upon completion of any service or repairs to this TV set, please ask the service technician
to perform the safety check described in the manufacturer’s service literature.
19 When a TV set reaches the end of its useful life, improper disposal could result in a picture
tube implosion. Ask a qualified service technician to dispose of the TV set.
20 Note to CATV system installer.
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of
the NEC that provides guidelines for proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system of the building, as close to the
point of cable entry as practical.
5
AV-32S565 5
5/11/04, 10:34:11 AM
Table of Contents
Quick Setup . . . . . . . . . . . 7
Sound Adjust . . . . . . . . . 38
Unpacking your TV . . . . . . . . . . . . 7
TV Model . . . . . . . . . . . . . . . . 8
TV Remote Control . . . . . . . . . . . 9
Getting Started . . . . . . . . . . . . . 10
The Remote Control . . . . . . . . . . 10
Connecting Your Devices . . . . . . . 11
Auto Tuner Setup . . . . . . . . . . 15
Sound Settings . . . . . .
Adjust Sound Settings . .
MTS (Multi-channel Sound)
Reset . . . . . . . . . . .
Remote Programming . . . . . 16
Setting CATV, VCR and DVD Codes
CATV or Satellite Codes . . . . .
VCR Codes . . . . . . . . . . .
DVD Codes . . . . . . . . . . .
Search Codes . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
16
16
17
18
19
Onscreen Menus . . . . . . . . 20
Using the Guide . . . . . . . . . . . . . 20
Onscreen Menu System . . . . . . . . . 21
Initial Setup . . . . . . . . . . 23
Auto Tuner Setup . . . . . . . . . . .
Channel Summary . . . . . . . . . . .
Channel Label . . . . . . . . . . .
V-Chip . . . . . . . . . . . . . . . . .
Set Lock Code . . . . . . . . . . . .
Auto Demo . . . . . . . . . . . . . .
Language . . . . . . . . . . . . . . .
Closed Caption . . . . . . . . . . . .
Auto Shut Off . . . . . . . . . . . . .
Tilt Correction . . . . . . . . . . . . .
Noise Muting . . . . . . . . . . . . .
Front Panel Lock . . . . . . . . . . .
Video Input Label . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
23
23
24
25
31
31
32
32
33
33
33
34
34
Picture Adjust . . . . . . . . . 35
Picture Settings . . . . . . . . . . .
Adjust Picture Settings . . . . . . .
Color Temperature . . . . . . . . . .
Digital Noise Clear . . . . . . . . . .
VSM . . . . . . . . . . . . . . . . .
Natural Cinema . . . . . . . . . .
Reset . . . . . . . . . . . . . . . .
. .
. .
. .
. .
. .
. .
. .
35
35
35
36
36
36
37
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
38
38
38
38
Clock Timers . . . . . . . . . . 39
Set Clock . . . . . . . . . . . . . . . . 39
On/Off Timer . . . . . . . . . . . . . . . 40
Button Functions . . . . . . . 41
Multi Screen Function . . . . . . . . .
Twin . . . . . . . . . . . . . . . .
Index . . . . . . . . . . . . . . . .
Freeze . . . . . . . . . . . . . . .
Swap . . . . . . . . . . . . . . . .
Select . . . . . . . . . . . . . . . .
Power . . . . . . . . . . . . . . . . .
Number Buttons . . . . . . . . . . . .
Tune . . . . . . . . . . . . . .
Input . . . . . . . . . . . . . . . . . .
Channel +/- . . . . . . . . . . . . .
Volume +/- . . . . . . . . . . . . . .
Return+ . . . . . . . . . . . . . .
Sound . . . . . . . . . . . . . . . . .
Muting . . . . . . . . . . . . . . . . .
Video Status . . . . . . . . . . . . . .
TheaterPro D6500K . . . . . . . . . .
Sleep Timer . . . . . . . . . . . . . .
Display . . . . . . . . . . . . . . . .
C.C. . . . . . . . . . . . . . . . . . .
Aspect . . . . . . . . . . . . . . . .
Aspect Ratios . . . . . . . . . . . .
Menu . . . . . . . . . . . . . . . . .
OK . . . . . . . . . . . . . . . . . .
Back . . . . . . . . . . . . . . . . . .
TV/CATV Slide Switch . . . . . . . . .
VCR/DVD Slide Switch . . . . . . . .
VCR Buttons . . . . . . . . . . . . . .
DVD Buttons . . . . . . . . . . . . . .
Light . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
41
41
42
42
42
42
43
43
43
43
43
43
44
44
44
45
45
45
46
46
47
47
48
48
48
49
49
49
49
49
Appendices . . . . . . . . . . 50
Troubleshooting . . . . . . . . . . . . .
Warranty . . . . . . . . . . . . . . . . .
Authorized Service Centers . . . . . . .
Specifications . . . . . . . . . . . . .
Notes . . . . . . . . . . . . . .
50
51
52
53
54
6
AV-32S565 6
5/11/04, 10:34:11 AM
Quick Setup
Unpacking your TV
Thank you for your purchase of a JVC Color Television. Before you begin setting up your new
television, please check to make sure you have all of the following items. In addition to this
guide, your television box should include:
1 Television
1 Remote Control
SWAP
DISPLAY
INPUT
1
2
4
5
7
8
TUNE
0
SLEEP TIMER
SOUND
VIDEO STATUS
C.C.
SELECT
THEATER PRO ASPECT
MUTING
AA Alkaline
MULTI SCREEN
TWIN
INDEX
FREEZE
AA Alkaline
POWER
TV CATV VCR DVD
TM
Two AA
Batteries
3
6
9
RETURN+
LIGHT
OK
CH +
VOL
+
VOL
–
CH –
BACK
MENU
VCR CHANNEL
PREV NEXT
VCR/DVD
POWER TV/VCR
REW
PLAY
REC
STOP
OPEN/CLOSE
FF
PAUSE
STILL/PAUSE
RM-C1257G
TV
Once you have unpacked your television, the next step is to connect it to your antenna/
cable or satellite system and to connect the audio/video devices you want to use with your
television. To make these connections you will use plugs like the ones illustrated below.
Coaxial Cables
Used to connect an
external antenna or
cable TV system to
your TV.
S-Video Cable
Component Cables
Composite Cables
Audio Cables
Used to connect audio/
video devices like
VCRs, DVD players,
stereo amplifiers, game
consoles, etc.
Used to make video
connections with S-Video
VCRs, Camcorders and
DVD players.
We recommend that before you start using your new television, you read your entire User’s
Guide so you can learn about your new television’s many great features. If you’re anxious to
start using your television right away, a quick setup guide follows on the next few pages.
7
AV-32S565 7
5/11/04, 10:34:12 AM
Quick Setup
TV Model
NOTE: Before you connect your television to another device, please refer to the proper
diagrams for your specific TV and remote. These will help assist you in understanding
how to connect your television to another device, as well as use the remote to set up
your television.
Rear Panel Diagram
MODEL: AV-32S565
75Ω
( VHF/UHF )
UNPLUG THE POWER
CORD FROM AC OUTLET
BEFORE REMOVING THE
REAR COVER
When the rear cover is removed, follow
"CAUTION AT DISASSEMBLY"
procedure in the service manual before
plugging the TV's power cord into an
AC outlet. Failure to follow the
procedure will result in PERMANENT
damage to some of the television
features.
DÉBRANCHEZ LE CORDON DE LA
PRISE DE COURANT C. A. AVANT
DE RETIRER LE COUVERCLE
ARRIÈRE.
Une fois le couvercle arrière déposé
suivez l procédure « ATTENTION
LORS DU DÉMONTAGE » décrite
dans une prise c.a. L'omission de
suivre la procédure causera des
dommages PERMANENTS à
certaines fonctions du téléviseur.
AUDIO OUT
R
L
COMPONENT VIDEO
AUDIO
R
VIDEO S VIDEO
INPUT 2
INPUT 1
L
OVER
INPUT 3
Y
Y
INPUT 2
Pb
Pb
INPUT 1
Pr
Pr
OVER
Front Panel Diagram
MODEL: AV-32S565
OVER
S–VIDEO
VIDEO
INPUT-4
L/ MONO – AUDIO–R
MENU
CHANNEL
VOLUME
OPERATE
8
AV-32S565 8
5/11/04, 10:34:12 AM
Quick Setup
TV Remote Control
POWER
TV CATV VCR DVD
MULTI SCREEN
TWIN
INDEX
FREEZE
SWAP
DISPLAY
SLEEP TIMER
SOUND
SELECT
INPUT
1
2
3
4
5
6
7
8
TUNE
VIDEO STATUS
C.C.
THEATER PRO ASPECT
MUTING
9
RETURN+
0
LIGHT
OK
CH +
VOL
+
VOL
–
CH –
BACK
MENU
VCR CHANNEL
PREV NEXT
VCR/DVD
POWER TV/VCR
REW
PLAY
FF
REC
STOP
PAUSE
OPEN/CLOSE
STILL/PAUSE
RM-C1257G
TV
RM-C1257G
MODEL:
AV-32S565
• For information on remote control buttons, see pages 41 - 49.
9
AV-32S565 9
5/11/04, 10:34:12 AM
Quick Setup
Getting Started
Getting Started
These quick setup pages will provide you, in three easy steps, with the basic information you
need to begin using your new television right away.
If you have questions, or for more detailed information on any of these steps, please consult
other sections of this manual.
Step 1 – The Remote Control
Before you can operate your remote control, you first
need to install the batteries (included).
Lift and pull the latch on the back of the remote control
to open. Insert two batteries (included) carefully noting
the “+” and “–” markings, placing the “–” end in the unit
first. Snap the cover back into place.
When you change the batteries, try to complete the
task within three minutes. If you take longer than
three minutes, the remote control codes for your
VCR, DVD, and/or cable box/satellite receiver may
have to be reset. See pages 16 - 18.
Key Feature Buttons
The four key feature buttons at the center of the remote
can be used for basic operation of the television. The top
and bottom buttons will scan forward and back through the
available channels. To move rapidly through the channels
using JVC’s Hyperscan feature, press and hold CH+ or
CH–. The channels will zip by at a rate of five channels per
second. The right and left buttons will turn the volume up or
down. These buttons are also marked with four arrows and
are used with JVC’s onscreen menu system. To use the
onscreen menus, press the MENU button.
MUTING
OK
CH +
VOL
+
VOL
–
CH –
BACK
MENU
VCR/DVD
Basic Operation
POWER
Turn the television on and off by pressing the POWER button at the top right
corner of the remote.
• Make sure the TV/CATV switch is set to TV. Move the switch to CATV only if
you need to operate a cable box.
TV CATV
• Slide the VCR/DVD selector switch to VCR to control a VCR. Slide to
DVD to control a DVD player. Please see pages 16 to 18 for instructions on
programming your remote control to operate a cable box, VCR or DVD player.
V VCR DVD
10
AV-32S565 10
5/11/04, 10:34:12 AM
Quick Setup
Connections
Step 2 – Connecting Your Devices
Please follow the flow chart below to determine which connection setup is right for you. Then,
refer to the appropriate diagrams to connect your television to other devices that you may
have. After you are finished connecting your devices, plug the power cord into the nearest
power outlet and turn on the TV.
A VCR is not necessary for operation of the television. If you follow these diagrams and the
television does not work properly, contact your local cable operator.
• To connect a DVD player, see Diagram #3. A DVD player is optional.
• If you have a satellite television system, please refer to the satellite TV manual.
Do you use a Cable TV Box?
Yes
No
Do you have a VCR?
Do you have a VCR?
Yes
No
Yes
No
Diagram #2
Diagram #1
Diagram #3
Diagram #1
11
AV-32S565 11
5/11/04, 10:34:13 AM
Quick Setup
Connections
Diagram #1
Cable or Antenna
Output
Coaxial Cable
75Ω
( VHF/UHF )
OR
OUT
TV Rear Panel
IN
Cable Box
Note:
• If you do not have a cable box, connect the cable wire from the wall outlet into the back of
the TV.
Diagram #2
AUDIO
R
Cable or Antenna
Output
VIDEO S VIDEO
L
TV Rear Panel
OVER
INPUT 3
INPUT 2
75Ω
( VHF/UHF )
INPUT 1
OVER
IN
OUT OUT
Coaxial Cable
Two-Way
Splitter
OR
VCR
IN
IN
OUT
R
L
V
OUT
OUT
IN
Cable Box
Notes:
• If your VCR is a mono sound unit, it will have only one audio out jack. Connect it to the
LEFT AUDIO INPUT on the front of the TV.
• Use the S-Video connection if possible for superior picture quality.
• Your VCR must be turned on to view premium cable channels.
12
AV-32S565 12
5/11/04, 10:34:13 AM
Quick Setup
Connections
Notes:
• Green, blue and red are the most common colors for DVD cables. Some models may vary
colors. Please consult the user’s manual for your DVD player for more information.
• Be careful not to confuse the red DVD cable with the red audio cable. It is best to complete
one set of connections (DVD or audio output) before starting the other to avoid accidentally
switching the cables.
• You may also connect the DVD player to Input 1.
Diagram #3
Cable or Antenna
Output
Coaxial Cable
Two-Way
Splitter
IN
OUT OUT
R
L
V
IN
75Ω
( VHF/UHF )
IN
OUT
VCR
OUT
OR
COMPONENT VIDEO
AUDIO
R
VIDEO S VIDEO
INPUT 2
INPUT 1
L
OVER
TV Rear Panel
INPUT 3
Y
Y
INPUT 2
Pb
Pb
Pr
Pr
INPUT 1
OVER
AUDIO OUT
R
L
Y
Green
PB
Blue
PR
Red
OUT
DVD Player (OPTIONAL)
13
AV-32S565 13
5/11/04, 10:34:13 AM
Quick Setup
Connections
Connecting to a Camcorder
You may connect a camcorder, game console or other equipment to your television by using
the front input jacks (Input 4) located under the front panel door. To acces, push on the door
to open it. You can also connect these using the television’s rear input jacks, using the same
instructions.
INPUT-4
OVER
S–VIDEO
VIDEO
L/ MONO – AUDIO–R
– OR–
MENU
CHANNEL
VOLUME
OPERATE
Camcorder
1) Connect a yellow composite cable from the camcorder VIDEO OUT, into the VIDEO IN on
the side of the TV, OR connect an S-Video cable from the side of the TV to the camcorder.
2) Connect a white cable from the camcorder LEFT AUDIO OUT, into the LEFT AUDIO IN on
the side of the TV.
3) Connect a red cable from the camcorder RIGHT AUDIO OUT, into the RIGHT AUDIO IN on
the side of the TV.
Note:
• If your camcorder is a mono sound model it will have only one AUDIO OUT. Connect it to the
L/MONO on the front of the TV.
14
AV-32S565 14
5/11/04, 10:34:13 AM
Quick Setup
Auto Tuner Setup
Step 3 – Auto Tuner Setup
JVC’s onscreen menu system lets you set your television up to meet your own personal viewing
preferences. The menu screens and their features are discussed in detail in this book. The menu
settings are optional, you can set as many or as few of them as you wish. But to begin watching
your television right away you will need to run the Auto Tuner Setup. This lets your television
learn the channels it is able to receive. To run the Auto Tuner Setup follow the steps below.
Press the Menu button on the remote control
π†
To AUTO TUNER SETUP
è
To operate
AUTO TUNER SETUP
CABLE
TUNER MODE
PRESS
SELECT
OK
TO START
OPERATE
MENU
EXIT
è
To choose CABLE (if you are connected to a cable system) or AIR (if you use an
antenna)
π†
To move to START
è
To start Auto Tuner Setup
The Auto Tuner will now memorize all of the clear, active channels your television can receive.
This will take one or two minutes.
NOW
PROGRAMMING !
48
When the setup is finished, PROGRAMMING OVER ! is displayed. Your quick setup is now
complete. You can now begin watching your television, or you can continue on in this guide
for more information on programming your remote control, or using the JVC onscreen menu
system to customize your television viewing experience.
Cable Box and Satellite Users: After your auto tuner setup is complete, you may, (depending
on the type of hookup), have only 1 channel, usually 3 or 4 in the auto tuner memory. This is
normal.
STOP
The Quick Setup is complete
15
AV-32S565 15
5/11/04, 10:34:13 AM
Remote Programming
Setting the CATV, VCR and DVD Codes
You can program your remote to operate your cable box, satellite receiver, VCR or DVD
player by using the instructions and codes listed below. If the equipment does not respond
to any of the codes listed below or to the code search function, use the remote control
supplied by the manufacturer.
Cable Box or Satellite Codes
The remote control is programmed with cable box and satellite codes for power on/off,
channel up/down, and 10 key operation.
1) Find the cable box or satellite brand from the list of codes shown below.
2) Slide the 2-way selector switch to “CATV”.
3) Press and hold down the DISPLAY button, then enter the first code number listed with the 10
key pad.
4) Release the DISPLAY button, and confirm the operation of the cable box/satellite receiver.
• If your cable or satellite box does not respond to the first code, try the others listed. If it does
not respond to any code, try the search codes function, on page 19.
Cable Box
CODES
ABC
Archer
024
032, 025
Cableview
051, 032
Citizen
Curtis
Diamond
022, 051
058, 059
024, 032, 025
Eagle
Eastern
GC Brand
029
034
032, 051
022, 043
Gemini
General Instrument 065, 024, 025,
026, 027, 020,
021, 022, 057,
023
040, 041, 042,
Hamlin
045, 058, 064
049, 024
Hitachi
Jerrold
Macom
Cable Box
CODES
Puser
032
RCA
Realistic
061, 070
032
058, 064, 040,
041, 042, 045,
068
034
Regal
Regency
Rembrandt
Samsung
037, 032, 051,
038
051
Scientific Atlanta 057, 058, 059
CODES
Echostar
100, 113, 114,
115
Express VU
100, 113
G.E.
106
G.I.
108
Gradiente
112
Hitachi
104, 111
HNS (Hughes) 104
SLMark
051, 047
Panasonic
105
Sprucer
051, 056
Philips
102, 103
Stargate
032, 051
Primestar
108
Telecaption
067
Proscan
106, 109, 110
Teleview
047, 051
RCA
106, 109, 110
065, 024, 025,
026, 027, 020,
021, 022, 057,
023
Texscan
044
Sony
107
Tocom
035, 036, 066
Star Choice
104, 108
Toshiba
050
Toshiba
101
049, 050, 051,
054
Unika
032, 025
Uniden
102, 103
Universal
022, 032
Magnavox
033
Memorex
Movietime
030
032, 051
Videoway
052
Viewstar
029, 030
Oak
039, 037, 048
Zenith
063, 046
Panasonic
055, 056, 060,
071, 073
063
Zenith/Drake
Satellite
046
Paragon
Digital
Satellite
Systems
Philips
028, 029, 030,
052, 053, 031,
069
Pioneer
047, 062
Pulsar
051, 032
16
AV-32S565 16
5/11/04, 10:34:14 AM
Remote Programming
VCR Codes
The remote control is programmed with VCR codes for power on/off, play, stop, fast-forward,
rewind, pause, record, channel up/down operation.
1) Find the VCR brand from the list of codes shown below.
2) Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “VCR”.
3) Press and hold down the DISPLAY button, then enter the first code number listed with the 10
key pad.
4) Release the DISPLAY button, and confirm the operation of the VCR.
• If your VCR does not respond to the first code, try the others listed. If it does not respond to
any of the codes, try the search codes function on page 19.
• After you program your remote, some VCR buttons may not work properly. If so, use the
VCR’s remote.
• To record, hold down the REC button on the remote and press PLAY.
VCRs
CODES
VCRs
CODES
VCRs
CODES
Admiral
Aiwa
035
027, 032, 095
Marantz
003, 004, 005
Samsung
Marta
Memorex
064
024, 067
038, 040, 047,
048, 041, 042
058, 045, 093
037, 060, 062,
033, 089
089
029, 072, 073,
074
Audio Dynamic 003, 005
Bell & Howell
063, 071
Broksonic
020, 026, 094
Akai
Canon
CCE
Citizen
023, 025
043
064
Craig
Curtis Mathes
063, 029, 064
045, 024, 027,
093
043, 059, 024,
092
003, 004, 005
045, 093
Daewoo
DBX
Dimensia
MGA
Minolta
Mitsubishi
Multitech
NEC
Olympic
Optimus
Orion
Panasonic
Emerson
043, 026, 077,
061, 025, 042,
020, 076
Fisher
063, 066, 067,
065, 071, 091
Pentax
Funai
027, 026, 020,
000
033, 045, 024
037, 051, 049,
050, 089
Philco
G.E.
Go Video
Penney
Philips
Goldstar
064
Pioneer
Gradiente
083, 084, 081,
000, 001
Proscan
Hitachi
023, 045, 058,
027, 081, 093
Instant Replay
Quasar
024, 023
Jensen
003
JVC
000, 001, 002,
003, 004, 005
Kenwood
003, 004, 064,
005
LXI
027, 064, 058,
065, 066, 063,
067
Magnavox
031, 023, 024,
086
Radio Shack
RCA
Realistic
038, 040, 047,
048, 041, 042,
078, 090
047, 027, 062
003, 004, 005,
000
024, 023
028, 021, 035,
064
026, 020
023, 024, 021,
022
024, 058, 045,
063, 003, 004,
005, 093
058, 005, 045,
093
031, 024, 027,
023, 026, 020,
043
031, 023, 024,
086
023
045, 058, 023,
024, 031, 046,
059, 060, 033,
087, 093
021, 022, 023,
024
033, 024, 063,
036, 067, 040,
027
033, 045, 058,
023, 024, 031,
046, 059, 060,
083, 084, 085,
087, 093
Samtron
003, 026, 020,
052
063, 067, 091,
071
059, 060, 062,
Scott
067, 038, 040,
047, 048, 026,
020
Sears
063, 064, 065,
066, 058, 000,
001
075
Shintom
Sharp
035, 036, 080,
088
Signature 2000 027, 035
Sansui
Sanyo
Singer
Sony
075
028, 029, 030,
053, 054, 055
SV 2000
Sylvania
027
031, 023, 024,
027
027, 081
Symphonic
Tashiro
Tatung
Teac
064
003, 004, 005
003, 004, 027,
005
Technics
021, 022, 023,
024
024, 027, 070
059, 046, 079
Teknika
Toshiba
Vector Research 005
Wards
Yamaha
Zenith
035, 036, 067,
044, 064
063, 003, 004,
005
044, 082, 064,
094
024, 063, 036,
067, 040, 027
17
AV-32S565 17
5/11/04, 10:34:14 AM
Remote Programming
DVD Codes
The remote control is programmed with DVD codes for power on/off, play, stop, fast-forward,
rewind, previous/next chapter, tray open/close, and still/pause operation.
1) Find the DVD player brand from the list of codes shown below.
2) Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “DVD”.
3) Press and hold down the Display button, then enter the first code number listed with the 10
key pad.
4) Release the Display button, and confirm the operation of the DVD player.
• If your DVD player does not respond to the first code, try the others listed. If it does not
respond to any of the codes, try the search codes function on page 19.
• After you program your remote, some DVD buttons may not work properly. If so, use the
DVD player’s remote.
DVD Player
CODES
Aiwa
Apex
043
040
Denon
Hitachi
JVC
Kenwood
020, 037
030, 031
000
035
Konka
Mitsubishi
Onkyo
039
025
041
Oritron
Panasonic
Philips
Pioneer
044
020
023, 036
022
033
Raite
DVD Player
CODES
RCA
021, 026
Sampo
Samsung
Sharp
034
030
028
Silvania
Sony
038
Technics
020
Toshiba
Vialta
Wave
Yamaha
Zenith
023
050
042
020
027, 032
024, 045, 046,
047
18
AV-32S565 18
5/11/04, 10:34:14 AM
Remote Programming
Search Codes
Cable/Satellite Search Codes Function
1)
2)
3)
4)
Slide the first 2-Way Mode Selector switch to CATV.
Press the POWER and RETURN+ buttons. Hold for at least three seconds and release.
Press the POWER button on the remote, and see if the cable or satellite box responds.
If there was a response, press RETURN+. The codes are now set. If there was no
response, repeat Step 3. If you repeat Step 3 a total of 80 times without a response, use
the remote control that came with your equipment.
5) Press RETURN+ to exit.
VCR/DVD Search Codes Function
1) Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “VCR” or
“DVD”.
2) Press the VCR or DVD POWER and RETURN+ buttons. Hold for at least three seconds and
release.
3) Press the VCR or DVD POWER button, and see if the VCR or DVD responds.
4) If there was a response, press RETURN+. The codes are now set. If there was no
response, repeat Step 3. If you repeat Step 3 a total of 80 times for the VCR (40 times for
the DVD player), and there is no response, use the remote control that came with your
equipment.
5) Press Return+ to exit.
19
AV-32S565 19
5/11/04, 10:34:14 AM
Onscreen Menus
Using the Guide
Certain symbols are used throughout this guide to help you learn about the features of your
new television. The ones you will see most frequently are:
π† Up and Down arrows mean press the CH+ or CH– buttons. Pressing the CH+ or CH–
buttons let you:
• Move vertically in a main menu screen
• Move through a submenu screen
• Move to the next letter, number, or other choice in a submenu
• Back up to correct an error
• Scan through TV channels (when not in a menu screen)
è
Left and right arrows mean press the VOLUME+ or VOLUME– buttons to move left or right
to:
• Select a highlighted menu item
• Select an item in a submenu
• Select numbers in certain menu options
• Turn the volume up or down (when not in a menu screen)
The “press button” icon means you should press the button named on your remote
control. (Button names appear in SMALL CAPITAL LETTERS.)
The “helping arrow” icon points to the highlighted or selected item in a menu.
To bring up the onscreen menu, press the MENU button on the remote control. The item that
appears in green is the one currently selected. If you use the MENU button on the TV’s front
panel instead of the remote, an additional menu screen showing INPUT and VIDEO STATUS
will appear between INITIAL SETUP and PICTURE ADJUST.
INITIAL SETUP
PREVIOUS
AUTO TUNER SETUP
CHANNEL SUMMARY
V-CHIP
SET LOCK CODE
OFF
AUTO DEMO
NEXT PAGE
SELECT
OPERATE
(3/3)
MENU
EXIT
Note:
• Menus shown in this book are illustrations, not exact replications of the television’s onscreen
displays.
20
AV-32S565 20
5/11/04, 10:34:15 AM
Onscreen Menus
The Onscreen Menu System
Your television comes with JVC’s onscreen menu system. The onscreen menus let you make
adjustments to your television’s operation simply and quickly. Examples of the onscreen
menus are shown on the next page. Detailed explanations on using each menu follow later in
this guide.
The Onscreen Menu System
To open the onscreen menu system, press the MENU button on the remote control. You
navigate within the onscreen menus by using the four directional arrow buttons on the remote
control. (These buttons are also the CH +/– and VOL +/– buttons. Channel and volume functions
will not operate when the onscreen menu is active).
The selected feature and option on a menu screen are highlighted in a different color.
Selected Option
(Green)
LANGUAGE
CLOSED CAPTION
ENG. FRAN. ESP.
Selected Option
(Blue)
To move to a different feature use the π† arrows to move up or down the list. When you
press the up arrow at the top of the list or the down arrow at the bottom, the next menu screen
will appear. Use the arrows √ ® to select an option from the highlighted feature. Pressing
MENU on the remote control will close the onscreen menu system and return you to normal
television viewing.
Each menu and its features will be discussed in the following pages of this guide.
Notes:
• If you do not press any buttons for a few seconds, the onscreen menu will automatically
shut off.
• Button names in this guide are shown in SMALL CAPITAL LETTERS.
• Menus may appear in different sizes onscreen depending on the aspect ratio selected.
• Some menu items may not appear in menu screens when certain aspect ratios or inputs
are selected.
21
AV-32S565 21
5/11/04, 10:34:15 AM
Onscreen Menus
Press the MENU button
INITIAL SETUP
INITIAL SETUP
PREVIOUS
AUTO TUNER SETUP
CHANNEL SUMMARY
V-CHIP
PREVIOUS
LANGUAGE
OFF
MENU
TILT CORRECTION
(3/3)
NEXT PAGE
EXIT
SELECT
NEXT PAGE
OPERATE
OFF
AUTO SHUT OFF
SET LOCK CODE
AUTO DEMO
SELECT
ENG. FRAN. ESP.
CLOSED CAPTION
(2/3)
OPERATE
MENU
EXIT
INITIAL SETUP 02
INITIAL SETUP 03
PICTURE ADJUST
STANDARD
PREVIOUS
TINT
COLOR
00
00
PICTURE 00
BRIGHT
00
DETAIL
00
Note:
COLOR TEMPERATURE
NEXT PAGE
SELECT OPERATE
LOW
(1/2)
MENU
EXIT
PICTURE ADJUST 01
PICTURE ADJUST
PREVIOUS
STANDARD
DIG. NOISE CLEAR
VSM
NATURAL CINEMA
OFF
ON
AUTO
• When the MENU
button on the
TV front panel
is pressed, the
FRONT PANEL
CONTROL menu
between INITIAL
SETUP 03 and
PICTURE ADJUST
01 will appear.
INITIAL SETUP
PREVIOUS
ON
NOISE MUTING
OFF
FRONT PANEL LOCK
VIDEO INPUT LABEL
NEXT PAGE
SELECT
(1/3)
OPERATE
MENU
EXIT
INITIAL SETUP 01
RESET
NEXT PAGE
SELECT
(2/2)
OPERATE
MENU
EXIT
PICTURE ADJUST 02
CLOCK / TIMERS
SOUND ADJUST
PREVIOUS
PREVIOUS
BASS
TREBLE
BALANCE
MTS
00
00
00
STEREO SAP MONO
SET CLOCK
ON / OFF TIMER
RESET
NEXT PAGE
NEXT PAGE
SELECT
OPERATE
MENU
SOUND ADJUST
EXIT
SELECT
OPERATE
MENU
EXIT
CLOCK/TIMERS
22
AV-32S565 22
5/11/04, 10:34:15 AM
Initial Setup
Auto Tuner Setup
If you have already run the Auto Tuner as part of the quick setup earlier in this guide, please
skip ahead to “Channel Summary” to continue setting up your television. In Auto Tuner Setup,
the TV automatically scans through all available channels, memorizing the active ones and
skipping over blank ones or channels with weak signals. This means you scan using the
CHANNEL +/- buttons), you will receive only clear active channels.
Press the MENU button
π†
To AUTO TUNER SETUP
è
è
To operate
AUTO TUNER SETUP
CABLE
TUNER MODE
To choose CABLE or AIR
Press the OK button to start
PRESS
SELECT
OK
TO START
OPERATE
MENU
EXIT
Programming will take approximately 1 to 2 minutes. The auto tuner is finished when the
message PROGRAMMING OVER! appears onscreen.
Press the MENU button when finished
Channel Summary
Channel summary allows you to customize the line-up of channels received by your TV. You
can add or delete channels from the line-up or prevent any unauthorized viewers from watching
any or all 181 channels.
Press the MENU button
π†
è
CHANNEL SUMMARY
To CHANNEL SUMMARY
To operate
The Channel summary screen will now be displayed with
the channels set to scan marked with an “√”. You can delete
channels from the scan by removing the “√”. If any channels
were missed during auto tuner setup and you wish to add
them, you may by placing an “√” next to the channel number.
CHNO. SCAN ID
01
02
MTV
03
04
A&E
05
E!
SELECT
OK
CHNO. SCAN ID
06
HBO
07
L
08
09
10
OPERATE
MENU
EXIT
π
†√® To the SCAN column
Press the OK button to include or delete from scan
Press the MENU button when finished
You can block access to a channel by activating the channel lock.
Press the MENU button
π†
To CHANNEL SUMMARY
è
π
†√®
To operate
To the Lock Column (
)
Press the ZERO button to lock or unlock that channel
Press the MENU button when finished
23
AV-32S565 23
5/11/04, 10:34:16 AM
Initial Setup
How to set the channel label:
Press the MENU button
π†
è
π†
To CHANNEL SUMMARY
To operate
To the ID column
ID
CHANNEL 09
RESET
Press the OK button to enter
è
π†
To select the character you want
To move to the next space
PRESS
SELECT
OK
TO FINISH
OPERATE
MENU
EXIT
...continue to follow these directions for all four spaces
Press the OK button to finish
Your characters are now set
Press the MENU button when finished
If you want to reset the characters you set:
Press the MENU button
π†
è
π†
To CHANNEL SUMMARY
To enter
To select RESET
Press the OK button to finish
Your characters are now reset
Notes:
• You can use characters for: Alphabet, numbers, marks and spaces.
• It is possible to set the maximum of 40 channel labels.
• If you try to set more than the 40 maximum, the message "MEMORY OVERFLOW" will
appear.
You can block access to a channel by activating the channel lock.
Press the MENU button
π†
To CHANNEL SUMMARY
è
π
†√®
To operate
To the Lock Column (
)
Press the ZERO button to lock or unlock that channel
Press the MENU button when finished
24
AV-32S565 24
5/11/04, 10:34:16 AM
Initial Setup
Channel Guard Message
When a viewer attempts to watch a guarded channel, the following message appears:
To watch a channel that you have locked, enter the
Lock Code using the 10 key pad.
If the wrong code is entered, the message
“INVALID LOCK CODE!” will flash on the screen.
THIS CHANNEL IS LOCKED BY
CHANNEL GUARD.
PLEASE ENTER LOCK CODE BY
10 KEY PAD TO UNLOCK IT.
The channel cannot be accessed until the correct code
is entered.
NO. - - - -
Notes:
• Once a channel has been unlocked, it will remain unlocked until the television is turned off.
• See also “Set Lock Code”, page 31.
V-Chip
Your TV is equipped with V-Chip technology which enables you to block channels or content
that you feel to be inappropriate for children, based on US and Canada rating guidelines.
V-Chip has no effect on video signals from a DVD discs, VCR tapes or Camcorder connection.
Note: Some programs, and movies are broadcast without a ratings signal. Even if you set up
V-Chip ratings limits, these programs will not be blocked. See page 26 for information on how
to block unrated programs.
Note (for Canadian viewers): The V-Chip function is based on specifications designed for
the United States and therefore may not work properly in Canada.
You can customize the V-Chip settings of your television to match your personal tastes. The
V-Chip menu below is the starting point for your V-Chip settings
You can use US V-Chip settings (for programming broadcast from the United States), Canadian
V-Chip settings (for programming broadcast from Canada), and movie ratings. You may use
any or all of the settings (US V-Chip, Canada V-Chip, Movie ratings). Descriptions for setting
each of the three V-Chip formats appear in the next six pages along with descriptions of the
rating categories.
To access the rating categories:
Press the MENU button
π†
è
To V-CHIP
To operate (Lock icon
V-CHIP
will appear)
Press ZERO to access the V-Chip menu
è
π†
To turn V-Chip ON or OFF (V-Chip must be turned
ON for rating settings to operate)
To move to SET US TV RATINGS,
SET MOVIE RATINGS, or SET CANADIAN RATINGS
(see following pages for descriptions of each item)
V-CHIP
OFF
SET US TV RATINGS
SET MOVIE RATINGS
SET CANADIAN RATINGS ENG
SET CANADIAN RATINGS FRE
UNRATED
VIEW
SELECT
OPERATE
MENU
EXIT
25
AV-32S565 25
5/11/04, 10:34:17 AM
Initial Setup
Unrated Programs
Unrated programming refers to any programming which does not contain a rating signal.
Programming on television stations which do not broadcast rating signals will be placed in the
“Unrated Programming” category.
Examples of Unrated programs:
•
•
•
•
•
Emergency Bulletins
News
Public Service Announcements
Sports
Some Commercials
•
•
•
•
Locally Originated Programming
Political Programs
Religious Programs
Weather
Note:
• TV programs or movies that do not have rating signals will be blocked if the unrated category
is set to BLOCK.
Directions to Block Unrated Programs
You can block programs that are not rated.
Press the MENU button
π†
è
To V-CHIP
To operate (The lock icon
V-CHIP
appears)
Press ZERO to access V-Chip setup options
π†
è
To UNRATED
To VIEW or BLOCK
Press MENU when done
OFF
V-CHIP
SET US TV RATINGS
SET MOVIE RATINGS
SET CANADIAN RATINGS ENG
SET CANADIAN RATINGS FRE
UNRATED
SELECT
VIEW
OPERATE
MENU
EXIT
26
AV-32S565 26
5/11/04, 10:34:17 AM
Initial Setup
US V-Chip Ratings
U.S. PARENTAL RATING SYSTEMS
Programs with the following ratings are appropriate for children.
❒ TV Y is Appropriate for All Children
Programs are created for very young viewers and should be suitable for all ages, including
children ages 2 - 6.
❒ TV Y7 is for Older Children
Most parents would find such programs suitable for children 7 and above. These programs
may contain some mild fantasy violence or comedic violence, which children should be able
to discern from reality.
Programs with the following ratings are designed for the entire audience.
❒ TV G stands for General Audience
Most parents would find these programs suitable for all age groups. They contain little or no
violence, no strong language, and little or no sexual dialog or situations.
❒ TV PG Parental Guidance Suggested
May contain some, but not much, strong language, limited violence, and some suggestive
sexual dialog or situations. It is recommended that parents watch these programs first, or
with their children.
❒ TV 14 Parents Strongly Cautioned
Programs contain some material that may be unsuitable for children under the age of 14
including possible intense violence, sexual situations, strong coarse language, or intensely
suggestive dialog. Parents are cautioned against unattended viewing by children under 14.
❒ TV MA Mature Audiences Only
These programs are specifically for adults and may be unsuitable for anyone under 17
years of age. TV MA programs may have extensive V, S, L, or D.
Viewing Guidelines
In addition to the ratings categories explained above, information on specific kinds of content
are also supplied with the V-Chip rating. These types of content may also be blocked. The
content types are:
•
•
•
•
V/FV is for VIOLENCE/FANTASY VIOLENCE
S stands for SEXUAL CONTENT
L stands for strong LANGUAGE
D stands for suggestive DIALOG
27
AV-32S565 27
5/11/04, 10:34:17 AM
Initial Setup
Setting US V-Chip Ratings
Press the MENU button
π†
è
To V-CHIP
To operate (lock icon
V-CHIP
V-CHIP
appears)
Press ZERO to access the V-Chip menu
è
π†
è
To turn V-Chip ON or OFF
To move to SET US TV RATINGS
To operate
OFF
SET US TV RATINGS
SET MOVIE RATINGS
SET CANADIAN RATINGS ENG
SET CANADIAN RATINGS FRE
UNRATED
VIEW
SELECT
OPERATE
MENU
EXIT
Directions to set US V-Chip Ratings
Line up the cursor in the column (TV PG, TV G, etc.) with the content row (V/FV, S, etc.) and
press the π
† or √® to move the cursor to the correct location. Press OK to turn the locking
feature on or off. An item is locked if the
icon appears instead of a “—”.
For example. To block viewing of all TV 14 shows, move the cursor to the top row of that
column and add a lock icon. Once you’ve put a lock on the top row, everything in that column
is automatically locked.
π
†√® To the TV 14 Column
SET US TV RATINGS
Press the OK button to lock
TV
MA
TV
14
TV
PG
TV
G
TV
Y7
TV
Y
Press the MENU button when finished
V/FV
S
Note:
• If you want to change the setup, move the cursor to the top
column and change the lock icon to “—” by pressing OK
again. You may then select individual categories to block.
L
D
SELECT
OK
OPERATE
MENU
EXIT
28
AV-32S565 28
5/11/04, 10:34:18 AM
Initial Setup
Movies Ratings
❒ NR – Not Rated
This is a film which has no rating. In many cases these films were imported from countries
which do not use the MPAA ratings system. Other NR films may be from amateur producers
who didn’t intend to have their film widely released.
NR (Not Rated) Programming may contain all types of programming including children’s
programming, foreign programs, or adult material.
❒ G – General Audience
In the opinion of the review board, these films contain nothing in the way of sexual content,
violence, or language that would be unsuitable for audiences of any age.
❒ PG – Parental Guidance
Parental Guidance means the movie may contain some contents such as mild violence,
some brief nudity, and strong language. The contents are not deemed intense.
❒ PG-13 – Parents Strongly Cautioned
Parents with children under 13 are cautioned that the content of movies with this rating may
include more explicit sexual, language, and violence content than movies rated PG.
❒ R – Restricted
These films contain material that is explicit in nature and is not recommended for
unsupervised children under the age of 17.
❒ NC-17 – No One Under 17
These movies contain content which most parents would feel is too adult for their children
to view. Content can consist of strong language, nudity, violence, and suggestive or explicit
subject matter.
❒ X – No One under 18
Inappropriate material for anyone under 18.
Directions to set Movie (MPAA) Ratings
Press the MENU button
π†
è
To V-CHIP
To operate (Lock icon
appears)
Press ZERO to access V-Chip setup options
π†
è
To SET MOVIE RATINGS
To enter movies menu
For example:
To block viewing of X and NC-17 rated from shows:
SET MOVIE RATINGS
π
†√® To the X Column
Press the OK button to lock
X
NC17
R PG13 PG
G
π
†√® To the NC-17 Column
Press the OK button to lock
Press the MENU button to finish
NR
SELECT
OK
OPERATE
MENU
EXIT
29
AV-32S565 29
5/11/04, 10:34:18 AM
Initial Setup
Canadian V-Chip Ratings
❒ E – Exempt
Exempt programming includes: news, sports, documentaries and other information
programming, talk shows, music videos, and variety programming.
❒ C – Programming Intended for Children
Violence Guidelines: There will be no realistic scenes of violence. Depictions of aggressive
behavior will be infrequent and limited to portrayals that are clearly imaginary, comedic or
unrealistic in nature.
❒ C8+ – Programming Intended for Children 8 and Over
Violence Guidelines: Any realistic depictions of violence will be infrequent, discreet, of low
intensity and will show the consequences of the acts. There will be no offensive language,
nudity or sexual content.
❒ G – General Audience
Programming will contain little violence and will be sensitive to themes which could affect
younger children.
❒ PG – Parental Guidance
Programming intended for a general audience, but which may not be suitable for younger
children. Parents may consider some content not appropriate for children aged 8-13.
❒ 14+ – 14 Years and Older
Parents are strongly cautioned to exercise discretion in permitting viewing by pre-teens and
early teens. Programming may contain mature themes and scenes of intense violence.
❒ 18+ – Adult
Material intended for mature audiences only.
Directions to set Canadian V-Chip Ratings
Press the MENU button
π†
è
To V-CHIP
To operate (lock icon
appears)
Press ZERO to access V-Chip setup options
π†
è
To SET CANADIAN RATINGS ENG (for English)
To enter ratings menu
For example:
To block viewing of programming rated 14+ and 18+:
è
To the 18+ Column
Press the OK button to lock
è
SET CANADIAN RATINGS ENG
18+
PG
14+
G
C8
C
To the 14+ Column
Press the OK button to lock
Press the MENU button to finish
SELECT
OK
OPERATE
MENU
EXIT
30
AV-32S565 30
5/11/04, 10:34:18 AM
Initial Setup
Set Lock Code
Channel guard and V-Chip settings are protected by a four-digit lock code. Your TV comes preset with a lock code of “0000”. You may change the code to any four-digit number you wish. To
change the lock code, follow the steps below.
Press the MENU button
π†
è
To SET LOCK CODE
To operate (lock icon
SET LOCK CODE
LOCK CODE
0000
appears)
Press ZERO to access the lock code
The first digit will be highlighted
è
π†
PRESS
To select the number
To move to the next digit
SELECT
OK
TO FINISH
OPERATE
MENU
EXIT
Continue to follow these directions for all four numbers
Press the OK button to finish (your lock code is now set)
Press the MENU button when finished
When a viewer attempts to watch a blocked channel,
this message appears:
The channel will remain blocked until the correct lock
code is entered (see above for information on setting
your lock code).
THIS PROGRAMMING EXCEEDS
YOUR RATING LIMITS.
PLEASE ENTER LOCK CODE BY
10 KEY PAD TO UNLOCK IT.
NO. - - - -
Notes:
• After a power interruption you must reset the lock code.
• Write your lock code number down and keep it hidden from potential viewers.
• If you forget the lock code, a new code may be set using the steps listed above.
Auto Demo
This function lets you preview the many different viewing modes of your TV. It will cycle
through “Multi Screen Demo”, “Picture in Picture Demo”, the different “16:9” ratios and all of the
different “Video Status” modes.
Press the MENU button
π†
è
To AUTO DEMO
To turn AUTO DEMO ON or OFF
Note:
• To stop auto demo, press the MENU button, and select auto
demo by pressing the π† buttons, and turn it off by pressing
the è buttons. Press the MENU button to finish.
INITIAL SETUP
PREVIOUS
AUTO TUNER SETUP
CHANNEL SUMMARY
V-CHIP
SET LOCK CODE
AUTO DEMO
OFF
(4/4)
NEXT PAGE
SELECT
OPERATE
MENU
EXIT
31
AV-32S565 31
5/11/04, 10:34:19 AM
Initial Setup
Language
You can choose to view your onscreen menus in three languages: English, French (Français)
or Spanish (Español).
Press the MENU button
π†
è
To LANGUAGE
To choose a language: ENG. (English), FRAN.
(French) or ESP. (Spanish)
Press the MENU button when finished
INITIAL SETUP
PREVIOUS
LANGUAGE
ENG. FRAN. ESP.
CLOSED CAPTION
OFF
AUTO SHUT OFF
TILT CORRECTION
(2/3)
NEXT PAGE
SELECT
OPERATE
MENU
EXIT
Closed Caption
Many broadcasts now include an onscreen display of dialog called closed captions. Some
broadcasts may also include displays of additional information in text form. Your television can
access and display this information using the closed caption feature. To activate the closed
caption feature, follow the steps below.
Press the MENU button
π†
è
è
π†
è
To CLOSED CAPTION
To operate
To select CAPTION or TEXT in MODE
To select CAPTION or TEXT
To select a caption (CC1 to CC4) or text
channel (T1 to T4)
Press the OK button to save
CLOSED CAPTION
MODE
CAPTION
TEXT
CC1
TEXT
T1
PRESS
SELECT
OK
TO FINISH
OPERATE
MENU
EXIT
Press the MENU button when finished
Notes:
• Closed caption subtitles are usually found on closed caption channel CC1. Some programs
may include additional text information which is usually found on text channel T1. The other
channels are available for future use.
• Closed captioning may not work correctly if the signal being received is weak or if you are
playing a video tape.
• Most broadcasts containing closed captioning will display a notice at the start of the program.
• To select the mode, press the C.C. button. See page 46.
32
AV-32S565 32
5/11/04, 10:34:19 AM
Initial Setup
Auto Shut Off
This function automatically shuts off your TV when there is no signal from the channel the
TV is on.
Press the MENU button
π†
è
INITIAL SETUP
PREVIOUS
LANGUAGE
To AUTO SHUT OFF
To turn ON or OFF
ENG. FRAN. ESP.
CLOSED CAPTION
OFF
AUTO SHUT OFF
Press the MENU button when finished
TILT CORRECTION
• If the channel that you have on does not receive a
signal for more than one minute, the blinking text
“NOT RECEIVING A SIGNAL AUTO SHUT OFF IN 9 MIN.”
appears on the screen, and starts the countdown. If no
signal is being received within 10 minutes, the TV shuts itself off.
NEXT PAGE
SELECT
(3/4)
OPERATE
MENU
EXIT
Tilt Correction
This adjusts the pictures so that it looks even on the screen and not lopsided.
Press the MENU button
π†
è
è
INITIAL SETUP
To TILT CORRECTION
To enter
To adjust TILT CORRECTION
PREVIOUS
LANGUAGE
Press the MENU button when finished
TILT CORRECTION
ENG. FRAN. ESP.
CLOSED CAPTION
OFF
AUTO SHUT OFF
(3/4)
NEXT PAGE
SELECT
OPERATE
MENU
EXIT
Noise Muting
This feature inserts a blank blue screen over channels which are not broadcasting or are too
weak to be received clearly.
Press the MENU button
π†
è
To NOISE MUTING
To turn noise muting ON or OFF
Press the MENU button when finished
Note:
• Noise muting will not work during auto tuner setup or
when you operate channel summary.
INITIAL SETUP
PREVIOUS
ON
NOISE MUTING
OFF
FRONT PANEL LOCK
VIDEO INPUT LABEL
NEXT PAGE
SELECT
(1/3)
OPERATE
MENU
EXIT
33
AV-32S565 33
5/11/04, 10:34:20 AM
Initial Setup
Front Panel Lock
This allows you to lock the keys on the front of the TV, so that a child may not accidentally
change your viewing preferences.
Press the MENU button
π†
è
To FRONT PANEL LOCK
To turn ON or OFF
INITIAL SETUP
PREVIOUS
ON
NOISE MUTING
OFF
FRONT PANEL LOCK
Press the MENU button when finished
VIDEO INPUT LABEL
You can turn off this feature in the following ways:
NEXT PAGE
(2/4)
SELECT OPERATE
EXIT
• Unplug the power cord, and plug it back in. Do this if
your batteries die, or you lose your remote control.
• Use the remote control.
• Press the MENU button on the front of the TV for more than 3 seconds. In this case, the OSD
for FRONT PANEL LOCK will appear.
MENU
Note:
• To turn ON/OFF the TV, press the POWER button for more than 3 seconds. This feature will
remain ON.
Video Input Label
This function is used to label video input connections for
the onscreen displays.
Press the MENU button
INITIAL SETUP
PREVIOUS
NOISE MUTING
FRONT PANEL LOCK
π†
To VIDEO INPUT LABEL
VIDEO INPUT LABEL
è
To operate
π†
To select the desired video input
è
To select the desired preset input label (see
chart below)
Press the OK button to save
Press the MENU button when finished
Preset
Labels
Select when...
VCR
You have a VCR connected to the video input
DVD
You have a DVD connected to the video input
D-VHS
You have a Digital VCR connected to the video input
STB
You have a Set-top Box connected to the video input
SAT
You have a Satellite Receiver connected to the video input
AMP
You have an Amplifier connected to the video input
GAME
You have a Video Game connected to the video input
CAM
You have a Video Camera connected to the video input
DISC
You have a Video Disc player connected to the video input
ON
OFF
NEXT PAGE
SELECT
(2/4)
OPERATE
MENU
EXIT
VIDEO INPUT LABEL
VIDEO-1
VIDEO-2
VIDEO-3
VCR
DVD
SAT
VIDEO-4
GAME
PRESS
SELECT
OK
TO FINISH
OPERATE
MENU
EXIT
34
AV-32S565 34
5/11/04, 10:34:20 AM
Picture Adjust
Picture Settings
These settings allow you to change and adjust the way the picture appears on your television.
TINT
Tint allows you to adjust the levels of red and green in your TV picture.
COLOR
The color function lets you make all the colors in the TV picture appear either more vivid or
subtle.
PICTURE
Picture allows you to adjust the levels of black and white on the TV screen, giving you a darker
or brighter picture overall.
BRIGHT
You can adjust the overall brightness of the TV picture with the Bright control.
DETAIL
The Detail feature adjusts the level of fine detail displayed in the picture.
Adjust the Picture Settings
Press the MENU button
π†
è
To TINT, COLOR, PICTURE, BRIGHT or
DETAIL
To enter
TINT
è
π†
+02
To adjust the setting
To move to the next setting
PICTURE ADJUST
STANDARD
PREVIOUS
TINT
COLOR
00
00
PICTURE 00
BRIGHT
00
DETAIL
00
COLOR TEMPERATURE
NEXT PAGE
SELECT OPERATE
LOW
(1/2)
MENU
EXIT
Press the MENU button when finished
Color Temperature
You can decide how strong or dull the colors appear on the TV screen.
Press the MENU button
π†
è
To COLOR TEMPERATURE
To enter
COLOR TEMPERATURE
è
LOW HIGH
To set LOW or HIGH
Press the MENU button when finished
PICTURE ADJUST
STANDARD
PREVIOUS
TINT
COLOR
00
00
00
PICTURE
BRIGHT
00
DETAIL
00
COLOR TEMPERATURE
LOW
NEXT PAGE
SELECT
(1/2)
OPERATE
MENU
EXIT
35
AV-32S565 35
5/11/04, 10:34:21 AM
Picture Adjust
Digital Noise Clear
With digital noise clear, this helps take our static or noise from a channel that may not be
coming in clearly.
Press the MENU button
π†
è
π†
DIG. NOISE CLEAR
OFF
LOW
HIGH
To DIG. NOISE CLEAR
To enter
To select the mode “LOW”, “HIGH” or “OFF”
Press the MENU button when finished
(VSM) Velocity Scan Modulation
Velocity scan modulation circuitry varies the electron beam’s horizontal scanning speed to help
accentuate the differences in picture brightness to sharpen the edges of images.
Press the MENU button
π†
è
VSM
è
PICTURE ADJUST
To VSM
To enter
PREVIOUS
STANDARD
DIG. NOISE CLEAR
VSM
OFF
ON
NATURAL CINEMA
AUTO
ON OFF
To turn VSM ON or OFF
Press the MENU button when finished
RESET
NEXT PAGE
SELECT
(2/2)
OPERATE
MENU
EXIT
Natural Cinema
Natural cinema corrects the problem of blurred edges which may occur when viewing a program
originally shot on film (such as motion pictures) or animation. If you notice blurring at the edges
of these programs, choose NATURAL CINEMA and set it to AUTO. Natural Cinema helps correct
conversion errors that occur when film, which is shot at 24 frames-per-second, is broadcast at the
television rate of 30 frames-per-second.
Press the MENU button
π†
è
π†
NATURAL CINEMA
To NATURAL CINEMA
To enter
To select the mode “AUTO", "ON" or "OFF”
AUTO
ON
OFF
Press the MENU button when finished
Notes: The natural cinema mode is automatically set to “AUTO” in the following cases:
• Turning on or off
• Changing the channel or input mode
• Using multi-screen functions
36
AV-32S565 36
5/11/04, 10:34:21 AM
Picture Adjust
Reset
Reset resets all picture adjustments (tint, color, picture, bright, detail, color temperature, dig.
noise clear and VSM) at once to the default settings.
Press the MENU button
π†
è
To RESET
To enter
The onscreen menu disappears for a moment, and
then the settings are reset to the default setting for
all the picture adjustments.
Press the MENU button when finished
PICTURE ADJUST
PREVIOUS
STANDARD
DIG. NOISE CLEAR
VSM
NATURAL CINEMA
OFF
ON
AUTO
RESET
NEXT PAGE
SELECT
(2/2)
OPERATE
MENU
EXIT
37
AV-32S565 37
5/11/04, 10:34:21 AM
Sound Adjust
Sound Settings
These settings allow you to change and adjust the sound on your television.
BASS – You can increase or decrease the level of low-frequency sound in the TV’s audio with
the bass adjustment.
TREBLE – Use treble to adjust the level of high-frequency sound in your TV’s audio.
BALANCE – Adjust the level of sound between the TV’s left and right speakers with the
balance setting.
Adjust the Sound Settings
Press the MENU button
π†
è
π†
To BASS, TREBLE or BALANCE
To adjust the setting
To move to the next setting
Press the MENU button when finished
SOUND ADJUST
PREVIOUS
BASS
TREBLE
00
00
BALANCE
MTS
00
STEREO SAP MONO
RESET
NEXT PAGE
Notes:
SELECT
OPERATE
MENU
EXIT
• You can reset the sound adjustments (BASS, TREBLE
and BALANCE) you set at once as the default setting when you select reset. See page 37.
• You can adjust BALANCE only when A.H.S. is off. See page 44.
MTS (Multi-Channel Television Sound)
MTS technology allows several audio signals to be broadcast at once, giving you a choice
in what you wish to hear with a TV program. In addition to mono or stereo sound, an
MTS broadcast may also include a second audio program (SAP).
Press the MENU button
π†
è
To MTS
Select the mode
(The ON AIR arrow tells you if a broadcast is in stereo and/or
contains an SAP).
Press the MENU button when finished
SOUND ADJUST
PREVIOUS
BASS
TREBLE
00
00
BALANCE
MTS
00
STEREO SAP MONO
RESET
NEXT PAGE
Notes:
SELECT
OPERATE
MENU
EXIT
• Keep the TV in stereo mode to get the best sound quality. The sound will work in stereo
mode even if a certain broadcast is in mono sound only.
• Choose the mono setting to reduce excessive noise on a certain channel or broadcast.
• Selecting SAP will allow you to hear an alternative soundtrack, if one is available.
• MTS unavailable if your television’s input source is in input 1, 2, 3 or 4 mode, as described
on page 43.
Reset
Reset resets all Sound Adjustments (Bass, Treble and Balance) at once to the default settings.
See page 37 on how to use reset.
38
AV-32S565 38
5/11/04, 10:34:22 AM
Clock/Timers
Set Clock
Before you use any of your TV’s timer functions, you must first set the clock. You may precisely
set your clock using the XDS time signal broadcast by most public broadcasting stations. If you
do not have this in your area, you will have to set the clock manually. See manual clock set
below. To set the clock using the XDS signal:.
Press the MENU button
π†
To SET CLOCK
è
To operate
When you set the clock automatically, choose AUTO by pressing the
π†
To TIME ZONE
è
To select your time zone
ATLANTIC
SET CLOCK
EASTERN
HAWAII
√ or ® arrows.
CENTRAL
ALASKA
MOUNTAIN
PACIFIC
π†
To D.S.T. (daylight savings time)
è
To turn D.S.T. ON or OFF
MODE
TIME
TIME ZONE
D.S.T.
AUTO
-- : -- -ATLANTIC
ON
PRESS
SELECT
OK
TO FINISH
OPERATE
EXIT
MENU
Press OK to finish
Press the MENU button when finished
When you set the clock manually, choose MANUAL by pressing the
π†
To move to the hour
è
To set the hour
π†
To move to minutes
è
To set the minutes
Press OK to start clock
√ or ® arrows.
SET CLOCK
MODE
TIME
TIME ZONE
D.S.T.
MANUAL
-- : -- -ATLANTIC
ON
PRESS
THANK YOU !!
SELECT
OK
TO START CLOCK
OPERATE
MENU
EXIT
Press the MENU button when finished
Notes:
• D.S.T. can be used only for US and Canada when it is set to ON in the SET CLOCK menu.
• Only when the MODE set to AUTO, the Daylight Savings Time feature automatically adjusts
your TV’s clock for Daylight Savings. The clock will move forward one hour at 2:00 am on
the first Sunday in April. The clock will move back one hour at 2:00 am on the last Sunday in
October.
• You will have to reset the clock after a power interruption. You must set the clock before
operating any timer functions.
39
AV-32S565 39
5/11/04, 10:34:22 AM
Clock/Timers
On/Off Timer
The on/off timer lets you program your television to turn itself on or off. You can use it as an
alarm to wake up, to help you remember important programs, or as a decoy when you’re not
home.
Press the MENU button
π†
To ON/OFF TIMER
è
è
To operate (begins with ON TIME)
To set the hour (AM/PM) you want the TV to turn on
†
To move to minutes
è
To set the minutes
ON/OFF TIMER
7:00 PM
ON TIME
10:00 PM
OFF TIME
CHANNEL
03
CURRENT
EVERYDAY
ON VOLUME
MODE
NO
ON/OFF TIMER
PRESS
SELECT
OK
TO FINISH
OPERATE
†
To accept ON TIME and move to OFF TIME (the
time the TV will turn off). Set the OFF TIME the same way as ON TIME
†
To accept OFF TIME and move to CHANNEL
è
To select channel
†
To ON VOLUME
è
†
è
†
è
MENU
EXIT
To set the volume level
To move to MODE
Choose ONCE or EVERYDAY
To ON/OFF TIMER
Choose YES to accept the timer setting, choose NO if you don’t wish to accept
Press the OK button to finish
Press the MENU button to exit the menu
Notes:
• The on/off time cannot be set to locked or guarded channels.
• In order for the on/off timer to work, the clock must be set.
• After a power interruption, the timer settings must be reset.
40
AV-32S565 40
5/11/04, 10:34:23 AM
Button Functions
Multi Screen Function
Your television has two kinds of screen: PIP and INDEX (9 channels).
Note: After you press any multiscreen button, if you press the menu button, only the picture
adjust screen will appear.
Twin
Turn PIP on by pressing the TWIN button
Twin
07
02
TWIN
Each press of TWIN will shift the PIP window to a different corner and turn off.
TWIN
TWIN
TWIN
TWIN
"PIP OFF"
TWIN
Note:
• You cannot select the component input in the PIP mode. (Except if the input is a 525i
component signal).
• When you select the AUTO TUNER SETUP, CHANNEL SUMMARY, V-CHIP, the PIP window
turns off.
41
AV-32S565 41
5/11/04, 10:34:23 AM
Button Functions
Index
This allows you to quickly look at up to 9 channels at a time so that you can decide which one
to watch.
1
2
3
4
5
6
7
8
9
Notes:
• Only RF input signal will be displayed.
• You can watch the channel added in channel summary. See page 23.
Freeze
Pressing the FREEZE button causes the screen to change to the PIP screen display with the still
picture displayed on the right. In order to return to the normal display, press the FREEZE button
once again.
Swap
You can exchange the channel (or input) displayed in the PIP screen window for the main
screen image by pressing the SWAP button.
Select
With SELECT, you can select the picture (channel) while viewing PIP screen. When you press
SELECT button, the channel number on the top will be highlighted. Each press of SELECT will
shift the channel.
42
AV-32S565 42
5/11/04, 10:34:23 AM
Button Functions
Power
Turns the TV on or off.
Press the POWER button
Number Buttons - 10Key Pad
Use the number buttons on the remote control to move directly to a specific channel. For
example, to move to channel 12:
0 (ZERO)
1 (ONE)
2 (TWO)
Tune
Lets you decide the input channel and select it. After you press the number buttons on the
remote, press the TUNE button. For example, to move to channel 12:
1 (ONE)
2 (TWO)
Press the TUNE button
Input
Selects the signal input source for the television: Input-1, 2, 3 or 4 for video devices like VCR’s
DVD players, or camcorders.
Press the INPUT button
By every press of the INPUT button, you can change the input mode.
Notes:
• When you return to TV mode, press the RETURN+ button or direct 10 key pad.
• You can also access the FRONT CONTROL PANEL screen by using the MENU button on
the front of the TV instead of the remote control. It appears between INITIAL SETUP and
PICTURE ADJUST screen, and it has INPUT and VIDEO STATUS menus. Choose INPUT
by pressing Menu† on the front panel and choose a mode by using the CHANNEL+/- buttons
( √ OPERATE ® ).
Channel +/–
Use these buttons to move up or down all the available channels your TV is able to receive.
Volume +/–
Use these buttons to raise or lower the TV’s volume level.
43
AV-32S565 43
5/11/04, 10:34:23 AM
Button Functions
Return +
The Return+ button has two functions:
Return - Returns to the channel viewed just before the channel currently onscreen.
Return+ - Lets you program a specific channel to return to while scanning through the
channels using the CH+ and CH– buttons.
RETURN+ and hold for three seconds
RETURN CHANNEL
PROGRAMMED!
The channel currently active has been programmed as your return+ channel. Now scan
through the channels using the CHANNEL+/- buttons.
RETURN+
You will return to your programmed channel.
• To cancel your return+ channel, press and hold the RETURN+ button for three seconds. The
message “RETURN CHANNEL CANCELLED!” will appear.
• Return+ works only with the CHANNEL+/- buttons. Pressing any number key will cancel
return+.
Sound
HYPER SURROUND - Creates a deep, three-dimensional sound effect by channeling the
audio through the TV's front-firing speakers.
Press the SOUND button
π†
è
To select HYPER SURROUND
To choose the setting
SOUND EFFECT
HYPER SURROUND
ON OFF
Press the MENU when finished
SELECT
OPERATE
MENU
EXIT
Muting
The MUTING button instantly turns the volume down completely when you press it. Press
MUTING and the volume level will instantly go to zero. To restore the volume to its previous
level, press MUTING again.
44
AV-32S565 44
5/11/04, 10:34:24 AM
Button Functions
Video Status
The Video Status button gives you a choice of four TV picture display settings, including a
display of your own preferences.
Standard - Resets the picture display to the factory settings.
Dynamic - Gives a vivid picture with better contrast when viewing in
a brightly lit room.
VIDEO STATUS
STANDARD
DYNAMIC
THEATER
GAME
Theater - Gives a rich, film-like look to video when viewing in a dimly
lit room.
Game - Used for when you are playing video games connected to
your TV.
Press the VIDEO STATUS button
By every press of the VIDEO STATUS button, you change the mode.
Note:
• You can also change the mode by pressing the π† buttons.
• You can also access the FRONT CONTROL PANEL screen by using the MENU button on
the front of the TV instead of the remote control. It appears between INITIAL SETUP and
PICTURE ADJUST screen, and it has INPUT and VIDEO STATUS menus. Choose VIDEO
STATUS by pressing Menu† on the front panel and choose a mode by using the CHANNEL+/buttons ( √ OPERATE ® ).
TheaterPro D6500K
The TheaterPro D6500K color temperature technology function makes sure that the video you
watch is set to the standard color temperature, so that what you see is as true to what the film
to video editors intended it to be.
Press the THEATERPRO button
Sleep Timer
The Sleep Timer can turn the TV off for you after you fall asleep. Program it to work in intervals
of 15 minutes, for a total time of up to 180 minutes.
Press the SLEEP TIMER button
0 15 30 45 60 75 90 105 120 135 150 165 180
Sleep Timer Message
20 seconds before the automatic shutoff, this message will appear:
GOOD NIGHT!!
PUSH SLEEP TIMER BUTTON
TO EXTEND
You then have 20 seconds to press the SLEEP TIMER button to
delay the shut off for another 15 minutes.
45
AV-32S565 45
5/11/04, 10:34:24 AM
Button Functions
Display
The display screen shows the current status of timers and inputs.
Press the DISPLAY button
The screen to the right shows the following information:
The current channel or AV input (Channel 05)
The current time (12:20 pm)
Sleep timer status/minutes remaining (The Sleep Timer is off)
On/off timer status (Set to turn on everyday at 7:00 PM, off at
10:00 PM)
• Each Press of the DISPLAY button changes the display mode:
•
•
•
•
Display
Time
Channel
05
NOW
SLEEP TIMER
ON/OFF TIMER
ON TIME
OFF TIME
12:20 PM
OFF
EVERYDAY
7:00 PM
10:00 PM
Off
Display - Full screen shown above
Time - Shows the current time only
Channel - Shows the current channel
Off - Turns display off
Notes:
• You may also turn off the display at any step by pressing MENU.
• If the clock, sleep timer or on/off timer are not set, the display screen will show:
“CLOCK NOT SET”, “SLEEP TIMER OFF”, and “ON/OFF TIMER OFF” respectively.
C.C. (Closed Caption)
Use the C.C. (Closed Caption) button to select the mode of closed caption.
Press the C.C. button
OFF
ON
• When you select ON, it will be the mode selected in the Closed Caption Menu.
• See page 32 when you set the caption/text mode.
46
AV-32S565 46
5/11/04, 10:34:25 AM
Button Functions
Aspect
This feature will help you adjust the picture you are watching to give you the best possible
picture quality.
Aspect Ratios
4:3 - Use this aspect mode when you
are watching a 4:3 broadcast.
16:9 - If you select 16:9 aspect mode
while watching a 4:3 broadcast, this
will stretch the picture so as to fit into
the 16:9 format. When you select this
mode, black bars will appear on the top
and bottom of the TV screen.
16:9 - Use this aspect mode when you
are watching a 16:9 broadcast. This
is also referred to as "widescreen", for
example on a DVD disc. When you
select this mode, black bars will appear
on the top and bottom of the TV screen.
HD ZOOM - If you are watching a 4:3
high definition broadcast and you select
this aspect mode, it will zoom in on the
picture.
V STRETCH - If you are watching a 4:3
broadcast, this aspect mode will stretch
the picture vertically on your TV
47
AV-32S565 47
5/11/04, 10:34:25 AM
Button Functions
Aspect Ratios (Continued)
Press the ASPECT button
• By pressing the ASPECT button, you can change the size.
When you change the aspect ratios, it is different from their broadcast or recorded program.
NTSC, 480i, 480p
HD (1080i, 720p)
ASPECT
ASPECT
4:3
16:9
16:9
HD ZOOM
V STRETCH
Notes:
• You can also choose the size by pressing the π† buttons.
• When you change the aspect ratio or signal, reset the picture position to center.
Menu
The Menu button allows you to access JVC’s onscreen menu system. Press MENU to activate
the onscreen menu system.
• See individual topics like “Sound Adjust” for specific information on using menus.
OK
This button confirms your selection when you are in one of the onscreen menus.
Back
This button allows you to go back in the menu to change a selection or correct a mistake.
48
AV-32S565 48
5/11/04, 10:34:25 AM
Button Functions
TV/CATV Slide Switch
Use either the television’s own tuner or a cable box to select channels. Set this switch to TV to
operate the television’s built-in tuner. Move the switch to CATV to operate a cable box.
Note:
• See page 16 for information on programming your remote for cable box operation.
VCR/DVD Slide Switch
You can control a VCR or DVD player with the buttons on the lower part of the remote control.
Move the slide switch to VCR or DVD to operate.
Notes:
• The remote is preset with the code 000 to control JVC-brand VCR’s. For any other
manufacturer’s brand VCR, please see the code chart and instructions on page 17.
• The remote is preset with the code 000 to control JVC-brand DVD players. For any other
manufacturer’s brand DVD player, please see the code chart and instructions on page 18.
VCR Buttons
You can use this remote control to operate the basic functions of your VCR. These functions
include: play, record, rewind, fast-forward, stop, pause, channel scan, TV/VCR, power on, and
power off.
Move the selector switch to VCR to operate.
• The remote is preset with the code 000 to control JVC-brand VCR’s. For any other
manufacturer’s brand VCR, please see the code chart and instructions on page 17.
DVD Buttons
You can also use this remote control to operate the basic functions of your DVD player. These
functions include: play, rewind, fast-forward, stop, still/pause, previous/next, tray open/close,
power on, and power off.
Move the selector switch to DVD to operate.
• The remote is preset with the code 000 to control JVC-brand DVD players. For any other
manufacturer’s brand DVD player, please see the code chart and instructions on page 18.
Light
All remote control buttons are illuminated, except for the TV/CATV slide switch, VCR/DVD slide
switch and LIGHT button. Press the LIGHT button to turn the illumination on for 4 seconds.
49
AV-32S565 49
5/11/04, 10:34:25 AM
Troubleshooting
PROBLEMS
CHECK
There is no power
• See if the power cord became unplugged.
• Check for a blown fuse or circuit breaker or a power outage.
There is no picture
or sound
• The antenna could be disconnected.
• The input mode could be set improperly. See page 43.
• The tuner (Auto Tuner Setup) could be set improperly. See page 23.
• The TV station may be having difficulties. Check to see if other stations are working.
Remote control is not
operating properly or
at all
• Check to see that the batteries are still working and properly installed.
• Make sure the remote has a clear sight path to the TV.
• Check that the TV/CATV switch is in the proper position.
• You may be too far from the TV. You must be within 23 feet (7 meters).
You cannot select a
certain channel
• Make sure the channels have been programmed. See "Channel Summary", page 23.
• Check to see if the channel is locked. See "Channel Summary - Lock" page 24.
The power turns off
by itself
• Make sure the set did not become unplugged.
• Perhaps the On/Off Timer is set. See page 40.
• Check to see if the Sleep Timer was set. See page 45.
The clock is wrong
• The power was interrupted and the clock was not reset. See page 39.
The color quality
is poor
• Tint and Color may be improperly adjusted. See page 35.
• The Video Status mode may be turned to the wrong setting. See page 45.
There are lines
across the picture
• There could be interference from another electrical appliance, such as a computer,
another TV or VCR. Move any such appliances further away from the TV.
The picture is spotted
• There could be interference from a high-wattage appliance, like a hairdryer or vacuum,
operating nearby. Move the antenna away from the appliance or change to a coaxial
cable connection which is less prone to interference.
There are double
pictures (ghosts)
• A building or passing airplane can reflect the original signal and produce a second,
slightly delayed one. Adjust your antenna position.
Picture is snowy
(image noise)
• Your antenna may be damaged, disconnected or turned. Check the antenna
connection. If the antenna is damaged, replace it.
Screen is 40% black
• The Closed Caption Text mode is on. Turn it off in the Closed Caption Menu, page 32.
Stereo or bilingual
programs can't be
heard
• Make sure the MTS settings are correct. See "MTS" on page 38.
Static electricity
• It is normal to feel static electricity if you brush or touch the screen.
You hear occasional
crackling sounds
• It is normal for the TV to make crackling sounds when first turned on or off. Unless
the sound or picture become abnormal, this is fine.
50
AV-32S565 50
5/11/04, 10:34:26 AM
51
AV-32S565 51
5/11/04, 10:34:26 AM
52
AV-32S565 52
5/11/04, 10:34:26 AM
Specifications
MODEL
AV-32S565
Reception
Format
NTSC, BTSC System (Multi-Channel Sound)
Reception
Range
VHF 2 to 13, UHF 14 to 69
Sub Mid, Mid, Super, Hyper and Ultra bands
(181 channel frequency synthesizer system)
Power Source
AC 120V, 60Hz
Power
Consumption
215W
Screen Size
Audio Output
32 inch / 80 cm
measured diagonally
4:3 Ratio
7.5W + 7.5W
Speakers
2 x 4 3/4 inch / 5 x 12 cm oval x 2
Antenna
Terminal
75 ohms (VHF/UHF) (F-type connector)
External Input
Jacks
Video: 1 Vp-p, 75 ohms
Audio: 500mVrms (-4dBs) high impediance
S-Video Input
Jack
Y: 1Vp-p positive, 75 ohms (negative sync provided)
C: 0.286 Vp-p (burst signal), 75 ohms
Component
Input Jacks
Y: 1Vp-p positive, 75 ohms (negative sync provided)
PB/PR: 0.7 Vp-p, 75 ohms
Audio Output
Jacks (FIX)
500 mVrms (-4dBs) Low impedance
(400 Hz when modulated 100%)
Dimensions (In)
WxHxD (cm)
34 5/8 x 27 5/8 x 22 1/4
87.7 x 69.9 x 56.5
Weight (lbs / kg)
145.2 / 66
Accessories
Remote control unit x 1 / AA batteries x 2
Specifications subject to change without notice.
Note:
• Reception of channel A-5 ("95" of the TV set's on-screen cable channel numbers) is not
recommended for your TV set.
53
AV-32S565 53
5/11/04, 10:34:26 AM
Notes
54
AV-32S565 54
5/11/04, 10:34:26 AM
Notes
55
AV-32S565 55
5/11/04, 10:34:26 AM
JVC COMPANY OF AMERICA
Division of JVC Americas Corp.
1700 Valley Road
Wayne, New Jersey, 07470
AV-32S565 56
JVC CANADA, INC.
21 Finchdene Square
Scarborough, Ontario
Canada, M1X 1A7
5/11/04, 10:34:26 AM
Color Television Users Guide
For Models:
AV-32S585
AV-32S575
Illustration of AV-32S585 and RM-C1257G
Important Note:
In the spaces below, enter the model and serial number of your television (located
at the rear of the television cabinet). Staple your sales receipt or invoice to the
inside cover of this guide. Keep this user’s guide in a convenient place for future
reference. Keep the carton and original packaging for future use.
Model Number:
Serial Number:
AV-32S575\585 1
LCT1638-001A-A
0504TNH-II-IM
5/11/04, 10:27:33 AM
Important Safety Precautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: To reduce the risk of electric shock. Do not
remove cover (or back). No user serviceable
parts inside. Refer servicing to qualified service
personnel.
The lightning flash with arrowhead symbol, within an
equilateral triangle is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS TV
SET TO RAIN OR MOISTURE.
CAUTION:
TO INSURE PERSONAL SAFETY, OBSERVE THE FOLLOWING RULES
REGARDING THE USE OF THIS UNIT.
1. Operate only from the power source specified on the unit.
2. Avoid damaging the AC plug and power cord.
3. Avoid Improper installation and never position the unit where good ventilation is unattainable.
4. Do not allow objects or liquid into the cabinet openings.
5. In the event of trouble, unplug the unit and call a service technician. Do not attempt to repair
it yourself or remove the rear cover.
Changes or modifications not approved by JVC could void the warranty.
* When you don’t use this TV set for a long period of time, be sure to disconnect both the
power plug from the AC outlet and antenna for your safety.
* To prevent electric shock do not use this polarized plug with an extension cord, receptacle or
other outlet unless the blades can be fully inserted to prevent blade exposure.
IMPORTANT RECYCLING INFORMATION
This product utilizes both a Cathode Ray Tube (CRT) and other components that
contain lead. Disposal of these materials may be regulated in your community due to
environmental considerations. For disposal or recycling information, please contact
your local authorities, or the Electronic Industries Alliance: http://www.eiae.org
2
AV-32S575\585 2
5/11/04, 10:27:36 AM
• As an “ENERGY STAR®” partner,
JVC has determined that this
product or product model meets the
“ENERGY STAR®” guidelines for energy
efficiency.
Important Safeguards
CAUTION:
Please read and retain for your safety.
Electrical energy can perform many useful functions. This TV set has been engineered and
manufactured to assure your personal safety. But improper use can result in potential
electrical shock or fire hazards. In order not to defeat the safeguards incorporated in this
TV set, observe the following basic rules for its installation, use and servicing. Also follow all
warnings and instructions marked on your TV set.
INSTALLATION
1 Your TV set is equipped with a polarized AC line plug (one
blade of the plug is wider than the other). This safety feature
allows the plug to fit into the power outlet only one way.
Should you be unable to insert the plug fully into the outlet,
try reversing the plug. Should it still fail to fit, contact your
electrician.
(POLARIZED-TYPE)
2 Operate the TV set only from a power source as indicated on the TV set or refer to the
operating instructions for this information. If you are not sure of the type of power supply to
your home, consult your TV set dealer or local power company. For battery operation, refer
to the operating instructions.
3 Overloaded AC outlets and extension cords are dangerous, and so are frayed power cords
and broken plugs. They may result in a shock or fire hazard. Call your service technician for
replacement.
4 Do not allow anything to rest on or roll over the power cord, and do not place the TV set
where power cord is subject to traffic or abuse. This may result in a shock or fire hazard.
5 Do not use this TV set near water — for example, near a bathtub, washbowl, kitchen sink, or
laundry tub, in a wet basement, or near swimming pool, etc.
6 If an outside antenna is connected to the TV set, be sure the antenna system is grounded
so as to provide some protection against voltage surges and built-up static charges.
Section 810 of the National Electrical Code provides information with respect to proper
grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors, location of antenna discharge unit, connection
requirements for the grounding electrode.
3
AV-32S575\585 3
5/11/04, 10:27:36 AM
7 An outside antenna system should not be located in the vicinity of overhead power lines
or other electric light or power circuits, or where it can fall into such power lines or circuits.
When installing an outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be fatal.
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRICAL
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC - NATIONAL ELECTRIC CODE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ARTICLE 250, PART H)
8 TV sets are provided with ventilation openings in the cabinet to allow heat generated during
operation to be released.
Therefore:
— Never block the bottom ventilation slots of a portable TV set by placing it on a bed, sofa,
rug, etc.
— Never place a TV set in a “built-in” enclosure unless proper ventilation is provided.
— Never cover the openings with a cloth or other material.
— Never place the TV set near or over a radiator or heat register.
9 To avoid personal injury:
— Do not place a TV set on a sloping shelf unless properly secured.
— Use only a cart or stand recommended by the TV set manufacturer.
— Do not try to roll a cart with small casters across thresholds or deep pile carpets.
— Wall or shelf mounting should follow the manufacturer’s instructions, and should use a
mounting kit approved by the manufacturer.
Use
10 Caution children about dropping or pushing objects into the TV set through cabinet
openings. Some internal parts carry hazardous voltages and contact can result in a fire or
electrical shock.
11 Unplug the TV set from the wall outlet before cleaning. Do not use liquid or an aerosol
cleaner.
12 Never add accessories to a TV set that has not been designed for this purpose. Such
additions may result in a hazard.
4
AV-32S575\585 4
5/11/04, 10:27:36 AM
PORTABLE CART WARNING
(Symbol provided by RETAC)
13 For added protection of the TV set during a lightning storm or when the TV set is to be left
unattended for an extended period of time, unplug it from the wall outlet and disconnect the
antenna. This will prevent damage to product due to lightning storms or power line surges.
14 A TV set and cart combination should be moved with care. Quick stops, excessive force,
and uneven surfaces may cause the TV set and cart combination to overturn.
Service
15 Unplug this TV set from the wall outlet and refer servicing to qualified service personnel
under the following conditions:
A. When the power cord or plug is damaged or frayed.
B. If liquid has been spilled into the TV set.
C. If the TV set has been exposed to rain or water.
D. If the TV set does not operate normally by following the operating instructions. Adjust
only those controls that are covered in the operating instructions as improper adjustment
of other controls may result in damage and will often require extensive work by a
qualified technician to restore the TV set to normal operation.
E. If the TV set has been dropped or damaged in any way.
F. When the TV set exhibits a distinct change in performance — this indicates a need for
service.
16 Do not attempt to service this TV set yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
17 When replacement parts are required, have the service technician verify in writing that the
replacement parts he uses have the same safety characteristics as the original parts. Use
of manufacturer’s specified replacement parts can prevent fire, shock, or other hazards.
18 Upon completion of any service or repairs to this TV set, please ask the service technician
to perform the safety check described in the manufacturer’s service literature.
19 When a TV set reaches the end of its useful life, improper disposal could result in a picture
tube implosion. Ask a qualified service technician to dispose of the TV set.
20 Note to CATV system installer.
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of
the NEC that provides guidelines for proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system of the building, as close to the
point of cable entry as practical.
5
AV-32S575\585 5
5/11/04, 10:27:37 AM
Table of Contents
Quick Setup . . . . . . . . . . . 7
Sound Adjust . . . . . . . . . 48
Unpacking your TV . . . . . . . . . . . . 7
TV Models . . . . . . . . . . . . . . . . 8
TV Remote Control . . . . . . . . . . . 9
Getting Started . . . . . . . . . . . . . 10
The Remote Control . . . . . . . . . . 10
Connecting Your Devices . . . . . . . 11
Interactive Plug In Menu . . . . . . . . 20
Sound Settings . . . . . .
Adjust Sound Settings . .
MTS (Multi-channel Sound)
Reset . . . . . . . . . . .
Remote Programming . . . . . 23
Setting CATV, VCR and DVD Codes
CATV or Satellite Codes . . . . .
VCR Codes . . . . . . . . . . .
DVD Codes . . . . . . . . . . .
Search Codes . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
23
23
24
25
26
Onscreen Menus . . . . . . . . 27
Using the Guide . . . . . . . . . . . . . 27
Onscreen Menu System . . . . . . . . . 28
Initial Setup . . . . . . . . . . 30
Auto Tuner Setup . . . . . . . . . . .
Channel Summary . . . . . . . . . . .
Channel Label . . . . . . . . . . .
V-Chip . . . . . . . . . . . . . . . . .
Set Lock Code . . . . . . . . . . . .
Auto Demo . . . . . . . . . . . . . .
Language . . . . . . . . . . . . . . .
Closed Caption . . . . . . . . . . . .
Auto Shut Off . . . . . . . . . . . . .
XDS ID . . . . . . . . . . . . . . . .
Tilt Correction . . . . . . . . . . . . .
Noise Muting . . . . . . . . . . . . .
Front Panel Lock . . . . . . . . . . .
V1 Smart Input . . . . . . . . . . .
Video Input Label . . . . . . . . . .
Digital-In . . . . . . . . . . . . . . . .
Digital-In Audio . . . . . . . . . . . . .
Center CH Input . . . . . . . . . . . .
Audio Out . . . . . . . . . . . . . . .
TV Speaker . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
30
30
31
32
38
38
39
39
40
40
40
41
41
42
42
43
43
44
44
44
Picture Adjust . . . . . . . . . 45
Picture Settings . . . . . . . . . . .
Adjust Picture Settings . . . . . . .
Color Temperature . . . . . . . . . .
Digital Noise Clear . . . . . . . . . .
VSM . . . . . . . . . . . . . . . . .
Natural Cinema . . . . . . . . . .
Reset . . . . . . . . . . . . . . . .
. .
. .
. .
. .
. .
. .
. .
45
45
45
46
46
46
47
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
48
48
48
48
Clock Timers . . . . . . . . . . 49
Set Clock . . . . . . . . . . . . . . . . 49
On/Off Timer . . . . . . . . . . . . . . . 50
Button Functions . . . . . . . 51
Multi Screen Function . . . . . . . . .
Twin . . . . . . . . . . . . . . . .
Index . . . . . . . . . . . . . . . .
Freeze . . . . . . . . . . . . . . .
Swap . . . . . . . . . . . . . . . .
Select . . . . . . . . . . . . . . . .
Power . . . . . . . . . . . . . . . . .
Number Buttons . . . . . . . . . . . .
Tune . . . . . . . . . . . . . .
Input . . . . . . . . . . . . . . . . . .
Channel +/- . . . . . . . . . . . . .
Volume +/- . . . . . . . . . . . . . .
Return+ . . . . . . . . . . . . . .
Sound . . . . . . . . . . . . . . . . .
Muting . . . . . . . . . . . . . . . . .
Video Status . . . . . . . . . . . . . .
TheaterPro D6500K . . . . . . . . . .
Sleep Timer . . . . . . . . . . . . . .
Display . . . . . . . . . . . . . . . .
C.C. . . . . . . . . . . . . . . . . . .
Aspect . . . . . . . . . . . . . . . .
Aspect Ratios . . . . . . . . . . . .
Menu . . . . . . . . . . . . . . . . .
OK . . . . . . . . . . . . . . . . . .
Back . . . . . . . . . . . . . . . . . .
TV/CATV Slide Switch . . . . . . . . .
VCR/DVD Slide Switch . . . . . . . .
VCR Buttons . . . . . . . . . . . . . .
DVD Buttons . . . . . . . . . . . . . .
Light . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
51
51
52
52
52
52
53
53
53
53
53
53
54
54
54
55
55
55
56
56
57
57
58
58
58
59
59
59
59
59
Appendices . . . . . . . . . . 60
Troubleshooting . . . . . . . . . . .
Warranty . . . . . . . . . . . . . . .
Authorized Service Centers . . . . .
Specifications . . . . . . . . . . .
.
.
.
.
.
.
.
.
60
61
62
63
6
AV-32S575\585 6
5/11/04, 10:27:37 AM
Quick Setup
Unpacking your TV
Thank you for your purchase of a JVC Color Television. Before you begin setting up your new
television, please check to make sure you have all of the following items. In addition to this
guide, your television box should include:
1 Television
1 Remote Control
SWAP
DISPLAY
INPUT
1
2
4
5
7
8
TUNE
0
SLEEP TIMER
SOUND
VIDEO STATUS
C.C.
SELECT
THEATER PRO ASPECT
MUTING
3
6
9
RETURN+
LIGHT
OK
CH +
VOL
+
VOL
–
CH –
BACK
MENU
VCR CHANNEL
PREV NEXT
VCR/DVD
POWER TV/VCR
REW
PLAY
REC
STOP
OPEN/CLOSE
AA Alkaline
MULTI SCREEN
TWIN
INDEX
FREEZE
AA Alkaline
POWER
TV CATV VCR DVD
Two AA
Batteries
FF
PAUSE
STILL/PAUSE
Note: Your television
and/or remote
control may differ
from the examples
illustrated here.
ON TIMER
POWER
RM-C1257G
TV
Once you have unpacked your television, the next step is to connect it to your antenna/
cable or satellite system and to connect the audio/video devices you want to use with your
television. To make these connections you will use plugs like the ones illustrated below.
Coaxial Cables
Used to connect an
external antenna or
cable TV system to
your TV.
S-Video Cable
Component Cables
Composite Cables
Audio Cables
Used to connect audio/
video devices like
VCRs, DVD players,
stereo amplifiers, game
consoles, etc.
AV CompuLink Cable
Used to make video
connections with S-Video
VCRs, Camcorders and
DVD players.
Used to connect JVC
AV CompuLink capable components
for an automated home theater.
Note: AV-32S585 ONLY
We recommend that before you start using your new television, you read your entire User’s
Guide so you can learn about your new television’s many great features. If you’re anxious to
start using your television right away, a quick setup guide follows on the next few pages.
7
AV-32S575\585 7
5/11/04, 10:27:38 AM
Quick Setup
TV Models
NOTE: Before you connect your television to another device, please refer to the proper
diagrams for your specific TV and remote. These will help assist you in understanding
how to connect your television to another device, as well as use the remote to set up
your television.
Rear Panel Diagram
MODELS: AV-32S585, AV-32S575
Note: Television model AV-32S575
does not have AV Compulink III
75Ω
( VHF/UHF )
DIGITAL - IN
R
UNPLUG THE POWER
CORD FROM AC OUTLET
BEFORE REMOVING THE
REAR COVER
When the rear cover is removed, follow
"CAUTION AT DISASSEMBLY"
procedure in the service manual before
plugging the TV's power cord into an
AC outlet. Failure to follow the
procedure will result in PERMANENT
damage to some of the television
features.
CENTER
CHANNEL IN
SUBWOOFER
OUT
DÉBRANCHEZ LE CORDON DE LA
PRISE DE COURANT C. A. AVANT
DE RETIRER LE COUVERCLE
ARRIÈRE.
AUDIO
(ANALOG)
L
VIDEO
(DIGITAL)
Une fois le couvercle arrière déposé
suivez l procédure « ATTENTION
LORS DU DÉMONTAGE » décrite
dans une prise c.a. L'omission de
suivre la procédure causera des
dommages PERMANENTS à
certaines fonctions du téléviseur.
AUDIO
(DIGITAL)
AUDIO OUT
R
L
COMPONENT VIDEO
AUDIO
R
VIDEO S VIDEO
INPUT 2
INPUT 1
L
OVER
INPUT 3
AV
COMPULINK
Y
Y
INPUT 2
Pb
Pb
INPUT 1
Pr
Pr
OVER
Front Panel Diagram
MODELS: AV-32S585, AV-32S575
OVER
S–VIDEO
INPUT–4
VIDEO
L/ MONO – AUDIO–R
MENU
CHANNEL
VOLUME
OPERATE
8
AV-32S575\585 8
5/11/04, 10:27:38 AM
Quick Setup
TV Remote Control
POWER
TV CATV VCR DVD
MULTI SCREEN
TWIN
INDEX
FREEZE
SWAP
DISPLAY
SLEEP TIMER
SOUND
SELECT
INPUT
1
2
3
4
5
6
7
8
TUNE
VIDEO STATUS
C.C.
THEATER PRO ASPECT
MUTING
9
RETURN+
0
LIGHT
OK
CH +
VOL
+
VOL
–
CH –
BACK
MENU
VCR CHANNEL
PREV NEXT
VCR/DVD
POWER TV/VCR
REW
PLAY
FF
REC
STOP
PAUSE
OPEN/CLOSE
STILL/PAUSE
RM-C1257G
TV
RM-C1257G
MODELS:
AV-32S585
AV-32S575
• For information on remote control buttons, see pages 51 - 59.
9
AV-32S575\585 9
5/11/04, 10:27:38 AM
Quick Setup
Getting Started
Getting Started
These quick setup pages will provide you, in three easy steps, with the basic information you
need to begin using your new television right away.
If you have questions, or for more detailed information on any of these steps, please consult
other sections of this manual.
Step 1 – The Remote Control
Before you can operate your remote control, you first
need to install the batteries (included).
Lift and pull the latch on the back of the remote control
to open. Insert two batteries (included) carefully noting
the “+” and “–” markings, placing the “–” end in the unit
first. Snap the cover back into place.
When you change the batteries, try to complete the
task within three minutes. If you take longer than
three minutes, the remote control codes for your
VCR, DVD, and/or cable box/satellite receiver may
have to be reset. See pages 23 - 25.
Key Feature Buttons
The four key feature buttons at the center of the remote
can be used for basic operation of the television. The top
and bottom buttons will scan forward and back through the
available channels. To move rapidly through the channels
using JVC’s Hyperscan feature, press and hold CH+ or
CH–. The channels will zip by at a rate of five channels per
second. The right and left buttons will turn the volume up or
down. These buttons are also marked with four arrows and
are used with JVC’s onscreen menu system. To use the
onscreen menus, press the MENU button.
MUTING
OK
CH +
VOL
+
VOL
–
CH –
BACK
MENU
VCR/DVD
Basic Operation
POWER
Turn the television on and off by pressing the POWER button at the top right
corner of the remote. If this is the first time you are turning on the TV, the
interactive plug-in menu appears.
TV CATV
• Make sure the TV/CATV switch is set to TV. Move the switch to CATV only if
you need to operate a cable box.
• Slide the VCR/DVD selector switch to VCR to control a VCR. Slide to
DVD to control a DVD player. Please see pages 23 to 25 for instructions on
programming your remote control to operate a cable box, VCR or DVD player.
V VCR DVD
10
AV-32S575\585 10
5/11/04, 10:27:38 AM
Quick Setup
Connections
Step 2 – Connecting Your Devices
Please follow the flow chart below to determine which connection setup is right for you. Then,
refer to the appropriate diagrams to connect your television to other devices that you may
have. After you are finished connecting your devices, plug the power cord into the nearest
power outlet and turn on the TV.
A VCR is not necessary for operation of the television. If you follow these diagrams and the
television does not work properly, contact your local cable operator.
• To connect a DVD player, see Diagram #3. A DVD player is optional.
• If you have a satellite television system, please refer to the satellite TV manual.
Do you use a Cable TV Box?
Yes
No
Do you have a VCR?
Do you have a VCR?
Yes
No
Yes
No
Diagram #2
Diagram #1
Diagram #3
Diagram #1
11
AV-32S575\585 11
5/11/04, 10:27:39 AM
Quick Setup
Connections
Diagram #1
Cable or Antenna
Output
Coaxial Cable
75Ω
( VHF/UHF )
OR
OUT
TV Rear Panel
IN
Cable Box
Note:
• If you do not have a cable box, connect the cable wire from the wall outlet into the back of
the TV.
Diagram #2
AUDIO
R
Cable or Antenna
Output
VIDEO S VIDEO
L
TV Rear Panel
OVER
INPUT 3
INPUT 2
75Ω
( VHF/UHF )
INPUT 1
OVER
IN
OUT OUT
Coaxial Cable
Two-Way
Splitter
OR
VCR
IN
IN
OUT
R
L
V
OUT
OUT
IN
Cable Box
Notes:
• If your VCR is a mono sound unit, it will have only one audio out jack. Connect it to the
LEFT AUDIO INPUT on the front of the TV.
• Use the S-Video connection if possible for superior picture quality.
• Your VCR must be turned on to view premium cable channels.
12
AV-32S575\585 12
5/11/04, 10:27:39 AM
Quick Setup
Connections
Notes:
• Green, blue and red are the most common colors for DVD cables. Some models may vary
colors. Please consult the user’s manual for your DVD player for more information.
• Be careful not to confuse the red DVD cable with the red audio cable. It is best to complete
one set of connections (DVD or audio output) before starting the other to avoid accidentally
switching the cables.
• You may also connect the DVD player to Input 1.
Diagram #3
Cable or Antenna
Output
Coaxial Cable
Two-Way
Splitter
IN
OUT OUT
R
L
V
IN
75Ω
( VHF/UHF )
IN
OUT
VCR
OUT
OR
COMPONENT VIDEO
AUDIO
R
VIDEO S VIDEO
INPUT 2
INPUT 1
L
OVER
TV Rear Panel
INPUT 3
Y
Y
INPUT 2
Pb
Pb
Pr
Pr
INPUT 1
OVER
AUDIO OUT
R
L
Y
Green
PB
Blue
PR
Red
OUT
DVD Player (OPTIONAL)
13
AV-32S575\585 13
5/11/04, 10:27:39 AM
Quick Setup
Connections
Connecting to JVC AV CompuLink
Note: AV-32S585 ONLY
JVC’s AV CompuLink feature makes playing video tapes or DVDs totally automatic. Simply
insert a pre-recorded tape into your JVC brand VCR or DVD into your JVC DVD player
and the device will automatically turn on and begin playback. At the same time, using the
AV CompuLink, the VCR or DVD player sends a signal to the television telling it to turn on
and switch to the proper video input.
• The AV CompuLink cable may be included with the JVC AV CompuLink unit you
wish to connect. If it is not, contact JVC Parts Department at (800)-882-2345, or
www.jvcservice.com for part # EWP 805-012.
• AV CompuLink can only be used with JVC brand products.
AV Compu Link Cable
To Connect: Plug one end of the AV CompuLink cable
into the AV COMPULINK INPUT on your VCR, DVD, or
other CompuLink device. Plug the other end of the
AV CompuLink cable into the AV COMPULINK at the
rear of the television.
Note:
• The AV CompuLink cable has a male 3.5 mm (mono)
plug on each end.
TV Rear Panel
VCR
IN
V L R
IN
AV
COMPULINK
OUT
OUT
AV CompuLink
Notes:
• In order for the VCR playback to begin automatically, the recording tabs must be removed
from the VHS tape. If the tab is in place, automatic switching will occur when you push the
VCR’s Play button.
• If your JVC brand VCR has “A code/B code remote control switching” (see your VCR’s
instruction book), using VCR A code will switch the TV to input 1.
• Refer to your DVD instruction book for detailed connection information.
• To connect a JVC HiFi receiver or amplifier for a completely automated home theater, see
the receiver connection instructions for detailed connection information.
• AV CompuLink is compatible with select AV CompuLink receivers.
14
AV-32S575\585 14
5/11/04, 10:27:40 AM
Quick Setup
Connections
Connecting to a Camcorder
You may connect a camcorder, game console or other equipment to your television by using
the front input jacks (Input 4) located under the front panel door. To acces, push on the door
to open it. You can also connect these using the television’s rear input jacks, using the same
instructions.
OVER
S–VIDEO
INPUT–4
VIDEO
L/ MONO – AUDIO–R
– OR–
MENU
CHANNEL
VOLUME
OPERATE
Camcorder
1) Connect a yellow composite cable from the camcorder VIDEO OUT, into the VIDEO IN on
the side of the TV, OR connect an S-Video cable from the side of the TV to the camcorder.
2) Connect a white cable from the camcorder LEFT AUDIO OUT, into the LEFT AUDIO IN on
the side of the TV.
3) Connect a red cable from the camcorder RIGHT AUDIO OUT, into the RIGHT AUDIO IN on
the side of the TV.
Note:
• If your camcorder is a mono sound model it will have only one AUDIO OUT. Connect it to the
L/MONO on the front of the TV.
15
AV-32S575\585 15
5/11/04, 10:27:40 AM
Quick Setup
Connections
Connecting to an External Amplifier
Subwoofer Out - Use a powered subwoofer with the surround feature to simulate a home
theater system. Simply connect the subwoofer to the back of the TV.
TV Rear Panel
SUBWOOFER
OUT
AUDIO OUT
R
L
Speaker
Speaker
Amplifier
Powered
Subwoofer
1) Connect a white cable from the LEFT AUDIO OUTPUT on the back of the TV to the
LEFT AUDIO INPUT on the amplifier.
2) Connect a red cable from the RIGHT AUDIO OUTPUT on the back of the TV to the
RIGHT AUDIO INPUT on the amplifier.
3) Connect a black cable from the SUBWOOFER OUT on the back of the TV to
the LINE INPUT of the subwoofer.
Notes:
• Refer to your amplifier’s manual for more information.
• You can use AUDIO OUTPUT for your home theater system.
Connecting to the Surround Amplifier
In multi-channel sound such as 5.1 channel, the speech characters are played back from the
center speaker.
A center speaker in a movie theater is set in back of the screen so it can recreate a
conversation scene in the movie more natually. By using your TV's speaker as the center
speaker, you can obtain the same sound effect as in a movie theater in you home theater
sound system.
TV Rear Panel
Front
Front
Surround
CENTER
CHANNEL IN
CENTER CHANNEL OUTPUT
(VARIABLE OUTPUT)
1) Connect the Pin cable from the TV's CENTER CHANNEL INPUT terminal to the surround
amplifier's CENTER CHANNEL OUTPUT terminal.
Note:
• Please read the benefit of this feature on page 44.
16
AV-32S575\585 16
5/11/04, 10:27:40 AM
Quick Setup
Connections
Connecting to a Digital TV Receiver
By connecting a Digital TV Reciever, high definition pictures can be displayed on your TV in
their digital form.
DTV Decoder
DIGITAL OUT
AUDIO OUT
L
R
TV Rear Panel
DIGITAL - IN
R
AUDIO
(ANALOG)
L
HDMI to DVI Cable
After the connections have been made,
tighten the screw to secure the cables.
VIDEO
(DIGITAL)
AUDIO
(DIGITAL)
1) Connect the HDMI to DVI Cable from the DIGITAL OUT on the back of your DTV decoder, to
the DIGITAL-IN on the back of your television.
2) Connect a red cable from the DTV decoder RIGHT AUDIO OUT, to the RIGHT AUDIO
DIGITAL-IN on the back of your television.
3) Connect a white cable from the DTV decoder LEFT AUDIO OUT, to the LEFT AUDIO
DIGITAL-IN on the back of your television.
• The digital-in terminal is not compatible with the picture signal of a personal computer.
• Use a HDMI to DVI cable (commercially available) in order to digitally connect the television
with a DTV decoder.
Notes:
• If 480p signals (640x480 or 720x480) are displayed on the screen, the horizontal balance
may be slightly shifted. Access the “DIGITAL-IN” in the initial setup menu to adjust it. (Refer
to page 43.)
• When you do the above connection, set DIGITAL-IN AUDIO in the Initial Setup menu to
ANALOG. See "DIGITAL-IN AUDIO", page 43.
17
AV-32S575\585 17
5/11/04, 10:27:40 AM
Quick Setup
Connections
Connecting to a HDMI Compatible Device
By connecting a HDMI compatible device, high definition pictures can be displayed on your
TV in their digital form. Some HDMI devices can include DVD players, D-VHS or any HDMI
compatible device.
HDMI (High Definition Multimedia Interface) is the first industry supported, uncompressed, all
digital audio/video interface. HDMI provides and interface between any audio/video source,
such as a set-top box, DVD player, A/V receiver or an audio and/or video monitor, such as a
digital television (DTV).
HDMI Compatable Device
DIGITAL OUT
AUDIO OUT
L
R
TV Rear Panel
DIGITAL - IN
R
AUDIO
(ANALOG)
L
VIDEO
(DIGITAL)
HDMI Cable
AUDIO
(DIGITAL)
1) Connect the HDMI Cable from the DIGITAL OUT on the back of your DTV or HDMI device, to
the DIGITAL-IN on the back of your television.
Note:
• When you do the above connection, set DIGITAL-IN AUDIO in the Initial Setup menu to
DIGITAL. See "DIGITAL-IN AUDIO", page 43.
18
AV-32S575\585 18
5/11/04, 10:27:41 AM
Quick Setup
Connections
Connecting to an AV Receiver using your television's
V1 Smart Input
By connecting your AV Receiver to your television's V1 Smart Input, you can watch picture
sources from many different devices, without having to change or use the other input
connections on your TV. This allows you to free up the other input connections so you can
connect more devices to your television.
AV Receiver
MONITOR
OUT
TV Rear Panel
COMPONENT VIDEO
Y
AUDIO
R
VIDEO S VIDEO
INPUT 2
INPUT 1
L
OVER
PB
INPUT 3
Y
Y
PR
INPUT 2
Pb
Pb
Pr
Pr
MONITOR OUT
INPUT 1
OVER
1) Connect an S-Video Cable from the AV Receiver's MONITOR OUT, to the S-Video INPUT-1
on the back of your television.
2) Connect a Yellow Component Cable from the AV Receiver's MONITOR OUT, into the
VIDEO INPUT-1 on the back of your television.
3) Connect a Green Component Cable from the AV Receiver's Y MONITOR OUT, into the Y
VIDEO INPUT-1 on the back of your television.
4) Connect a Blue Component Cable from the AV Receiver's Pb MONITOR OUT, into the
Pb VIDEO INPUT-1 on the back of your television.
5) Connect a Red Component Cable from the AV Receiver's Pr MONITOR OUT, into the Pr
VIDEO INPUT-1 on the back of your television.
Notes:
• Please refer to your AV Receiver instruction manual for more information on connecting your
speakers and other devices like a DVD player.
• Use your AV Receiver's remote to switch to the different devices you have connected.
• Some AV Receivers may not respond when the V1 Smart Input function is turned on.
• If you have video connections for each input device connected to your AV Receiver, you
should not connect them using both S-Video and Composite connection at the same time
when you are using V1 Input as the V1 Smart Input. In this case we recommend using the
S-Video connection.
19
AV-32S575\585 19
5/11/04, 10:27:41 AM
Quick Setup
Plug-In Menu
Step 3 – The Interactive Plug In Menu
When you turn your television on for the first time the interactive plug-in menu will appear. The
plug-in menu helps you to get your TV ready to use by letting you set your preferences for:
• The language in which you want the onscreen menus to appear.
• Setting the TV’s clock to the correct time so your timer functions will work properly. You can
choose “AUTO” or “MANUAL” for setting the clock.
• The auto tuner setup of which channels you wish to receive.
We recommend you complete the interactive plug-in items before you start using your
television.
Language
After the “JVC INTERACTIVE PLUG IN MENU” has been displayed, the TV automatically
switches to the LANGUAGE settings. You can choose to view your onscreen menus in three
languages: English, French (Français) or Spanish (Español).
LANGUAGE/LANGUE/IDIOMA
è
To choose a language:
(English, Français or Español)
†
To NEXT (To set clock)
ENGLISH
NEXT
SELECT
OPERATE
MENU
EXIT
(To be continued...)
20
AV-32S575\585 20
5/11/04, 10:27:41 AM
Quick Setup
Plug-In Menu
Auto Clock Set
Before you use any of your TV’s timer functions, you must first set the clock. You may precisely
set your clock using the XDS time signal broadcast by most public broadcasting stations. If you
do not have this in your area, you will have to set the clock manually. See manual clock set
below. To set the clock using the XDS signal:
è
SET CLOCK
MODE
TIME
TIME ZONE
D.S.T.
AUTO
-- : -- -ATLANTIC
ON
NEXT
SELECT
OPERATE
MENU
To choose AUTO
†
To TIME ZONE
è
†
To select your time zone: (Atlantic, Eastern,
Central, Mountain, Pacific, Alaska or
Hawaii)
To move to D.S.T. (Daylight Savings Time)
è
To turn D.S.T. ON or OFF
†
To NEXT (To Auto Tuner Setup)
EXIT
Notes:
• The Daylight Savings Time feature automatically adjusts your TV’s clock for Daylight
Savings. The clock will move forward one hour at 2:00 am on the first Sunday in April. The
clock will move back one hour at 2:00 am on the last Sunday in October.
• You will have to reset the clock after a power interruption. You must set the clock before
operating any timer functions.
Manual Clock Set
To set your clock manually (without using the XDS signal), choose MANUAL. If you choose
AUTO, see auto clock set above.
SET CLOCK
MODE
TIME
TIME ZONE
D.S.T.
MANUAL
-- : -- -ATLANTIC
ON
è
To choose MANUAL
†
To TIME
è
To set the hour
†
To minute
è
To set the minute
†
To Start Clock
START CLOCK
SELECT
OPERATE
MENU
EXIT
Note:
• You will have to reset the clock after a power interruption. You must set the clock before
operating any timer functions.
(To be continued...)
21
AV-32S575\585 21
5/11/04, 10:27:42 AM
Quick Setup
Plug-In Menu
Auto Tuner Setup
In auto tuner setup, the TV automatically scans through all available channels, memorizing the
active ones and skipping over blank ones or channels with weak signals. This means when you
scan (using the Channel +/– buttons) you will receive only clear, active channels.
AUTO TUNER SETUP
TUNER MODE
è
To choose CABLE or AIR (or SKIP when
you skip Auto Tuner Setup)
†
To START
CABLE
NOW
PROGRAMMING !
START
SELECT
OPERATE
MENU
48
EXIT
Programming will take approximately
1 to 2 minutes.
When the setup is finished, THANK YOU!! SETUP IS NOW COMPLETE is displayed. Your
quick setup is now complete. You can now begin watching your television, or you can continue
on in this guide for more information on programming your remote control, or using the
JVC onscreen menu system to customize your television viewing experience.
Notes:
• Noise muting will not work during Auto Tuner Setup.
• Skip appears only for interactive plug-in menu.
• The interactive plug-in menu setting does not appear if your TV has been turned on before.
In this case, use the menu to perform these settings. See pages 39, 49 and 30.
Cable Box and Satellite Users: After your auto tuner setup is complete, you may, (depending
on the type of hookup), have only 1 channel, usually 3 or 4 in the auto tuner memory. This is
normal.
STOP
The Quick Setup is complete
22
AV-32S575\585 22
5/11/04, 10:27:42 AM
Remote Programming
Setting the CATV, VCR and DVD Codes
You can program your remote to operate your cable box, satellite receiver, VCR or DVD
player by using the instructions and codes listed below. If the equipment does not respond
to any of the codes listed below or to the code search function, use the remote control
supplied by the manufacturer.
Cable Box or Satellite Codes
The remote control is programmed with cable box and satellite codes for power on/off,
channel up/down, and 10 key operation.
1) Find the cable box or satellite brand from the list of codes shown below.
2) Slide the 2-way selector switch to “CATV”.
3) Press and hold down the DISPLAY button, then enter the first code number listed with the 10
key pad.
4) Release the DISPLAY button, and confirm the operation of the cable box/satellite receiver.
• If your cable or satellite box does not respond to the first code, try the others listed. If it does
not respond to any code, try the search codes function, on page 26.
Cable Box
CODES
ABC
Archer
024
032, 025
Cableview
051, 032
Citizen
Curtis
Diamond
022, 051
058, 059
024, 032, 025
Eagle
Eastern
GC Brand
029
034
032, 051
022, 043
Gemini
General Instrument 065, 024, 025,
026, 027, 020,
021, 022, 057,
023
040, 041, 042,
Hamlin
045, 058, 064
049, 024
Hitachi
Jerrold
Macom
Cable Box
CODES
Puser
032
RCA
Realistic
061, 070
032
058, 064, 040,
041, 042, 045,
068
034
Regal
Regency
Rembrandt
Samsung
037, 032, 051,
038
051
Scientific Atlanta 057, 058, 059
CODES
Echostar
100, 113, 114,
115
Express VU
100, 113
G.E.
106
G.I.
108
Gradiente
112
Hitachi
104, 111
HNS (Hughes) 104
SLMark
051, 047
Panasonic
105
Sprucer
051, 056
Philips
102, 103
Stargate
032, 051
Primestar
108
Telecaption
067
Proscan
106, 109, 110
Teleview
047, 051
RCA
106, 109, 110
065, 024, 025,
026, 027, 020,
021, 022, 057,
023
Texscan
044
Sony
107
Tocom
035, 036, 066
Star Choice
104, 108
Toshiba
050
Toshiba
101
049, 050, 051,
054
Unika
032, 025
Uniden
102, 103
Universal
022, 032
Magnavox
033
Memorex
Movietime
030
032, 051
Videoway
052
Viewstar
029, 030
Oak
039, 037, 048
Zenith
063, 046
Panasonic
055, 056, 060,
071, 073
063
Zenith/Drake
Satellite
046
Paragon
Digital
Satellite
Systems
Philips
028, 029, 030,
052, 053, 031,
069
Pioneer
047, 062
Pulsar
051, 032
23
AV-32S575\585 23
5/11/04, 10:27:42 AM
Remote Programming
VCR Codes
The remote control is programmed with VCR codes for power on/off, play, stop, fast-forward,
rewind, pause, record, channel up/down operation.
1) Find the VCR brand from the list of codes shown below.
2) Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “VCR”.
3) Press and hold down the DISPLAY button, then enter the first code number listed with the 10
key pad.
4) Release the DISPLAY button, and confirm the operation of the VCR.
• If your VCR does not respond to the first code, try the others listed. If it does not respond to
any of the codes, try the search codes function on page 26.
• After you program your remote, some VCR buttons may not work properly. If so, use the
VCR’s remote.
• To record, hold down the REC button on the remote and press PLAY.
VCRs
CODES
VCRs
CODES
VCRs
CODES
Admiral
Aiwa
035
027, 032, 095
Marantz
003, 004, 005
Samsung
Marta
Memorex
064
024, 067
038, 040, 047,
048, 041, 042
058, 045, 093
037, 060, 062,
033, 089
089
029, 072, 073,
074
Audio Dynamic 003, 005
Bell & Howell
063, 071
Broksonic
020, 026, 094
Akai
Canon
CCE
Citizen
023, 025
043
064
Craig
Curtis Mathes
063, 029, 064
045, 024, 027,
093
043, 059, 024,
092
003, 004, 005
045, 093
Daewoo
DBX
Dimensia
MGA
Minolta
Mitsubishi
Multitech
NEC
Olympic
Optimus
Orion
Panasonic
Emerson
043, 026, 077,
061, 025, 042,
020, 076
Fisher
063, 066, 067,
065, 071, 091
Pentax
Funai
027, 026, 020,
000
033, 045, 024
037, 051, 049,
050, 089
Philco
G.E.
Go Video
Penney
Philips
Goldstar
064
Pioneer
Gradiente
083, 084, 081,
000, 001
Proscan
Hitachi
023, 045, 058,
027, 081, 093
Instant Replay
Quasar
024, 023
Jensen
003
JVC
000, 001, 002,
003, 004, 005
Kenwood
003, 004, 064,
005
LXI
027, 064, 058,
065, 066, 063,
067
Magnavox
031, 023, 024,
086
Radio Shack
RCA
Realistic
038, 040, 047,
048, 041, 042,
078, 090
047, 027, 062
003, 004, 005,
000
024, 023
028, 021, 035,
064
026, 020
023, 024, 021,
022
024, 058, 045,
063, 003, 004,
005, 093
058, 005, 045,
093
031, 024, 027,
023, 026, 020,
043
031, 023, 024,
086
023
045, 058, 023,
024, 031, 046,
059, 060, 033,
087, 093
021, 022, 023,
024
033, 024, 063,
036, 067, 040,
027
033, 045, 058,
023, 024, 031,
046, 059, 060,
083, 084, 085,
087, 093
Samtron
003, 026, 020,
052
063, 067, 091,
071
059, 060, 062,
Scott
067, 038, 040,
047, 048, 026,
020
Sears
063, 064, 065,
066, 058, 000,
001
075
Shintom
Sharp
035, 036, 080,
088
Signature 2000 027, 035
Sansui
Sanyo
Singer
Sony
075
028, 029, 030,
053, 054, 055
SV 2000
Sylvania
027
031, 023, 024,
027
027, 081
Symphonic
Tashiro
Tatung
Teac
064
003, 004, 005
003, 004, 027,
005
Technics
021, 022, 023,
024
024, 027, 070
059, 046, 079
Teknika
Toshiba
Vector Research 005
Wards
Yamaha
Zenith
035, 036, 067,
044, 064
063, 003, 004,
005
044, 082, 064,
094
024, 063, 036,
067, 040, 027
24
AV-32S575\585 24
5/11/04, 10:27:43 AM
Remote Programming
DVD Codes
The remote control is programmed with DVD codes for power on/off, play, stop, fast-forward,
rewind, previous/next chapter, tray open/close, and still/pause operation.
1) Find the DVD player brand from the list of codes shown below.
2) Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “DVD”.
3) Press and hold down the Display button, then enter the first code number listed with the 10
key pad.
4) Release the Display button, and confirm the operation of the DVD player.
• If your DVD player does not respond to the first code, try the others listed. If it does not
respond to any of the codes, try the search codes function on page 26.
• After you program your remote, some DVD buttons may not work properly. If so, use the
DVD player’s remote.
DVD Player
CODES
Aiwa
Apex
043
040
Denon
Hitachi
JVC
Kenwood
020, 037
030, 031
000
035
Konka
Mitsubishi
Onkyo
039
025
041
Oritron
Panasonic
Philips
Pioneer
044
020
023, 036
022
033
Raite
DVD Player
CODES
RCA
021, 026
Sampo
Samsung
Sharp
034
030
028
Silvania
Sony
038
Technics
020
Toshiba
Vialta
Wave
Yamaha
Zenith
023
050
042
020
027, 032
024, 045, 046,
047
25
AV-32S575\585 25
5/11/04, 10:27:43 AM
Remote Programming
Search Codes
Cable/Satellite Search Codes Function
1)
2)
3)
4)
Slide the first 2-Way Mode Selector switch to CATV.
Press the POWER and RETURN+ buttons. Hold for at least three seconds and release.
Press the POWER button on the remote, and see if the cable or satellite box responds.
If there was a response, press RETURN+. The codes are now set. If there was no
response, repeat Step 3. If you repeat Step 3 a total of 80 times without a response, use
the remote control that came with your equipment.
5) Press RETURN+ to exit.
VCR/DVD Search Codes Function
1) Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “VCR” or
“DVD”.
2) Press the VCR or DVD POWER and RETURN+ buttons. Hold for at least three seconds and
release.
3) Press the VCR or DVD POWER button, and see if the VCR or DVD responds.
4) If there was a response, press RETURN+. The codes are now set. If there was no
response, repeat Step 3. If you repeat Step 3 a total of 80 times for the VCR (40 times for
the DVD player), and there is no response, use the remote control that came with your
equipment.
5) Press Return+ to exit.
26
AV-32S575\585 26
5/11/04, 10:27:43 AM
Onscreen Menus
Using the Guide
Certain symbols are used throughout this guide to help you learn about the features of your
new television. The ones you will see most frequently are:
π† Up and Down arrows mean press the CH+ or CH– buttons. Pressing the CH+ or CH–
buttons let you:
• Move vertically in a main menu screen
• Move through a submenu screen
• Move to the next letter, number, or other choice in a submenu
• Back up to correct an error
• Scan through TV channels (when not in a menu screen)
è
Left and right arrows mean press the VOLUME+ or VOLUME– buttons to move left or right
to:
• Select a highlighted menu item
• Select an item in a submenu
• Select numbers in certain menu options
• Turn the volume up or down (when not in a menu screen)
The “press button” icon means you should press the button named on your remote
control. (Button names appear in SMALL CAPITAL LETTERS.)
The “helping arrow” icon points to the highlighted or selected item in a menu.
To bring up the onscreen menu, press the MENU button on the remote control. The item that
appears in green is the one currently selected. If you use the MENU button on the TV’s front
panel instead of the remote, an additional menu screen showing INPUT and VIDEO STATUS
will appear between INITIAL SETUP and PICTURE ADJUST. The “interactive plug-in menu” will
appear the first time the TV is plugged in.
INITIAL SETUP
PREVIOUS
AUTO TUNER SETUP
CHANNEL SUMMARY
V-CHIP
SET LOCK CODE
OFF
AUTO DEMO
NEXT PAGE
SELECT
OPERATE
(4/4)
MENU
EXIT
Note:
• Menus shown in this book are illustrations, not exact replications of the television’s onscreen
displays.
27
AV-32S575\585 27
5/11/04, 10:27:43 AM
Onscreen Menus
The Onscreen Menu System
Your television comes with JVC’s onscreen menu system. The onscreen menus let you make
adjustments to your television’s operation simply and quickly. Examples of the onscreen
menus are shown on the next page. Detailed explanations on using each menu follow later in
this guide. For information about the interactive plug-in Menu, see pages 20 - 22.
The Onscreen Menu System
To open the onscreen menu system, press the MENU button on the remote control. You
navigate within the onscreen menus by using the four directional arrow buttons on the remote
control. (These buttons are also the CH +/– and VOL +/– buttons. Channel and volume functions
will not operate when the onscreen menu is active).
The selected feature and option on a menu screen are highlighted in a different color.
Selected Option
(Green)
LANGUAGE
CLOSED CAPTION
ENG. FRAN. ESP.
Selected Option
(Blue)
To move to a different feature use the π† arrows to move up or down the list. When you
press the up arrow at the top of the list or the down arrow at the bottom, the next menu screen
will appear. Use the arrows √ ® to select an option from the highlighted feature. Pressing
MENU on the remote control will close the onscreen menu system and return you to normal
television viewing.
Each menu and its features will be discussed in the following pages of this guide.
Notes:
• If you do not press any buttons for a few seconds, the onscreen menu will automatically
shut off.
• Button names in this guide are shown in SMALL CAPITAL LETTERS.
• Menus may appear in different sizes onscreen depending on the aspect ratio selected.
• Some menu items may not appear in menu screens when certain aspect ratios or inputs
are selected.
28
AV-32S575\585 28
5/11/04, 10:27:44 AM
Onscreen Menus
Press the MENU button
INITIAL SETUP
INITIAL SETUP
PREVIOUS
AUTO TUNER SETUP
CHANNEL SUMMARY
V-CHIP
PREVIOUS
LANGUAGE
SET LOCK CODE
AUTO DEMO
OFF
NEXT PAGE
SELECT
EXIT
MENU
INITIAL SETUP 04
PICTURE ADJUST
STANDARD
PREVIOUS
TINT
COLOR
00
00
PICTURE 00
BRIGHT
00
DETAIL
00
COLOR TEMPERATURE
NEXT PAGE
SELECT OPERATE
LOW
(1/2)
MENU
EXIT
PICTURE ADJUST 01
PICTURE ADJUST
PREVIOUS
STANDARD
DIG. NOISE CLEAR
VSM
NATURAL CINEMA
OFF
ON
AUTO
RESET
NEXT PAGE
SELECT
(2/2)
OPERATE
MENU
EXIT
PICTURE ADJUST 02
AUTO SHUT OFF
OFF
XDS ID
OFF
TILT CORRECTION
NEXT PAGE
(4/4)
OPERATE
Notes:
• The DIGITAL-IN
menu can only be
displayed when a
480p picture signal
is input to the
digital-in terminal
and the picture is
being displayed on
the screen.
• When the MENU
button on the
TV front panel
is pressed, the
FRONT PANEL
CONTROL menu
between INITIAL
SETUP 04 and
PICTURE ADJUST
01 will appear.
• VIDEO INPUT
LABEL:
AV-32S575 ONLY.
SELECT
BALANCE
MTS
(3/4)
OPERATE
MENU
EXIT
INITIAL SETUP 03
INITIAL SETUP
PREVIOUS
ON
NOISE MUTING
OFF
FRONT PANEL LOCK
OFF
V1 SMART INPUT
VIDEO INPUT LABEL
NEXT PAGE
SELECT
(2/4)
OPERATE
EXIT
MENU
INITIAL SETUP 02
INITIAL SETUP
PREVIOUS
DIGITAL-IN
DIGITAL-IN AUDIO
SIZE1
DIGITAL
ON
VARI
CENTER CH INPUT
AUDIO OUT
ON
TV SPEAKER
NEXT PAGE
SELECT
(1/4)
OPERATE
MENU
EXIT
INITIAL SETUP 01
SOUND ADJUST
CLOCK / TIMERS
PREVIOUS
BASS
TREBLE
ENG. FRAN. ESP.
CLOSED CAPTION
PREVIOUS
00
00
00
STEREO SAP MONO
SET CLOCK
ON / OFF TIMER
RESET
NEXT PAGE
SELECT
OPERATE
NEXT PAGE
MENU
SOUND ADJUST
EXIT
SELECT
OPERATE
MENU
EXIT
CLOCK/TIMERS
29
AV-32S575\585 29
5/11/04, 10:27:44 AM
Initial Setup
Auto Tuner Setup
The auto tuner setup function is described on page 22 as the interactive plug-in menu. If you
need to run the auto tuner setup again, follow the steps below.
Press the MENU button
π†
To AUTO TUNER SETUP
è
è
To operate
To choose CABLE or AIR
AUTO TUNER SETUP
CABLE
TUNER MODE
Press the OK button to start
PRESS
SELECT
OK
TO START
OPERATE
MENU
EXIT
Programming will take approximately 1 to 2 minutes. The auto tuner is finished when the
message PROGRAMMING OVER! appears onscreen.
Press the MENU button when finished
Channel Summary
Channel summary allows you to customize the line-up of channels received by your TV. You
can add or delete channels from the line-up or prevent any unauthorized viewers from watching
any or all 181 channels.
Press the MENU button
π†
To CHANNEL SUMMARY
è
To operate
The Channel summary screen will now be displayed with
the channels set to scan marked with an “√”. You can delete
channels from the scan by removing the “√”. If any channels
were missed during auto tuner setup and you wish to add
them, you may by placing an “√” next to the channel number.
CHANNEL SUMMARY
CHNO. SCAN ID
01
02
MTV
03
04
05
A&E
E!
SELECT
OK
CHNO. SCAN ID
06
HBO
07
L
08
09
10
OPERATE
MENU
EXIT
π
†√® To the SCAN column
Press the OK button to include or delete from scan
Press the MENU button when finished
You can block access to a channel by activating the channel lock.
Press the MENU button
π†
To CHANNEL SUMMARY
è
π
†√®
To operate
To the Lock Column (
)
Press the ZERO button to lock or unlock that channel
Press the MENU button when finished
30
AV-32S575\585 30
5/11/04, 10:27:45 AM
Initial Setup
How to set the channel label: (AV-32S575 ONLY)
Press the MENU button
π†
è
π†
To CHANNEL SUMMARY
To operate
To the ID column
ID
CHANNEL 09
RESET
Press the OK button to enter
è
π†
To select the character you want
To move to the next space
PRESS
SELECT
OK
TO FINISH
OPERATE
MENU
EXIT
...continue to follow these directions for all four spaces
Press the OK button to finish
Your characters are now set
Press the MENU button when finished
If you want to reset the characters you set:
Press the MENU button
π†
è
π†
To CHANNEL SUMMARY
To enter
To select RESET
Press the OK button to finish
Your characters are now reset
Notes:
• You can use characters for: Alphabet, numbers, marks and spaces.
• It is possible to set the maximum of 40 channel labels.
• If you try to set more than the 40 maximum, the message "MEMORY OVERFLOW" will
appear.
You can block access to a channel by activating the channel lock.
Press the MENU button
π†
To CHANNEL SUMMARY
è
π
†√®
To operate
To the Lock Column (
)
Press the ZERO button to lock or unlock that channel
Press the MENU button when finished
31
AV-32S575\585 31
5/11/04, 10:27:45 AM
Initial Setup
Channel Guard Message
When a viewer attempts to watch a guarded channel, the following message appears:
To watch a channel that you have locked, enter the
Lock Code using the 10 key pad.
If the wrong code is entered, the message
“INVALID LOCK CODE!” will flash on the screen.
THIS CHANNEL IS LOCKED BY
CHANNEL GUARD.
PLEASE ENTER LOCK CODE BY
10 KEY PAD TO UNLOCK IT.
The channel cannot be accessed until the correct code
is entered.
NO. - - - -
Notes:
• Once a channel has been unlocked, it will remain unlocked until the television is turned off.
• See also “Set Lock Code”, page 38.
V-Chip
Your TV is equipped with V-Chip technology which enables you to block channels or content
that you feel to be inappropriate for children, based on US and Canada rating guidelines.
V-Chip has no effect on video signals from a DVD discs, VCR tapes or Camcorder connection.
Note: Some programs, and movies are broadcast without a ratings signal. Even if you set up
V-Chip ratings limits, these programs will not be blocked. See page 33 for information on how
to block unrated programs.
Note (for Canadian viewers): The V-Chip function is based on specifications designed for
the United States and therefore may not work properly in Canada.
You can customize the V-Chip settings of your television to match your personal tastes. The
V-Chip menu below is the starting point for your V-Chip settings
You can use US V-Chip settings (for programming broadcast from the United States), Canadian
V-Chip settings (for programming broadcast from Canada), and movie ratings. You may use
any or all of the settings (US V-Chip, Canada V-Chip, Movie ratings). Descriptions for setting
each of the three V-Chip formats appear in the next six pages along with descriptions of the
rating categories.
To access the rating categories:
Press the MENU button
π†
è
To V-CHIP
To operate (Lock icon
V-CHIP
will appear)
Press ZERO to access the V-Chip menu
è
π†
To turn V-Chip ON or OFF (V-Chip must be turned
ON for rating settings to operate)
To move to SET US TV RATINGS,
SET MOVIE RATINGS, or SET CANADIAN RATINGS
(see following pages for descriptions of each item)
V-CHIP
OFF
SET US TV RATINGS
SET MOVIE RATINGS
SET CANADIAN RATINGS ENG
SET CANADIAN RATINGS FRE
UNRATED
VIEW
SELECT
OPERATE
MENU
EXIT
32
AV-32S575\585 32
5/11/04, 10:27:46 AM
Initial Setup
Unrated Programs
Unrated programming refers to any programming which does not contain a rating signal.
Programming on television stations which do not broadcast rating signals will be placed in the
“Unrated Programming” category.
Examples of Unrated programs:
•
•
•
•
•
Emergency Bulletins
News
Public Service Announcements
Sports
Some Commercials
•
•
•
•
Locally Originated Programming
Political Programs
Religious Programs
Weather
Note:
• TV programs or movies that do not have rating signals will be blocked if the unrated category
is set to BLOCK.
Directions to Block Unrated Programs
You can block programs that are not rated.
Press the MENU button
π†
è
To V-CHIP
To operate (The lock icon
V-CHIP
appears)
Press ZERO to access V-Chip setup options
π†
è
To UNRATED
To VIEW or BLOCK
Press MENU when done
OFF
V-CHIP
SET US TV RATINGS
SET MOVIE RATINGS
SET CANADIAN RATINGS ENG
SET CANADIAN RATINGS FRE
UNRATED
SELECT
VIEW
OPERATE
MENU
EXIT
33
AV-32S575\585 33
5/11/04, 10:27:46 AM
Initial Setup
US V-Chip Ratings
U.S. PARENTAL RATING SYSTEMS
Programs with the following ratings are appropriate for children.
❒ TV Y is Appropriate for All Children
Programs are created for very young viewers and should be suitable for all ages, including
children ages 2 - 6.
❒ TV Y7 is for Older Children
Most parents would find such programs suitable for children 7 and above. These programs
may contain some mild fantasy violence or comedic violence, which children should be able
to discern from reality.
Programs with the following ratings are designed for the entire audience.
❒ TV G stands for General Audience
Most parents would find these programs suitable for all age groups. They contain little or no
violence, no strong language, and little or no sexual dialog or situations.
❒ TV PG Parental Guidance Suggested
May contain some, but not much, strong language, limited violence, and some suggestive
sexual dialog or situations. It is recommended that parents watch these programs first, or
with their children.
❒ TV 14 Parents Strongly Cautioned
Programs contain some material that may be unsuitable for children under the age of 14
including possible intense violence, sexual situations, strong coarse language, or intensely
suggestive dialog. Parents are cautioned against unattended viewing by children under 14.
❒ TV MA Mature Audiences Only
These programs are specifically for adults and may be unsuitable for anyone under 17
years of age. TV MA programs may have extensive V, S, L, or D.
Viewing Guidelines
In addition to the ratings categories explained above, information on specific kinds of content
are also supplied with the V-Chip rating. These types of content may also be blocked. The
content types are:
•
•
•
•
V/FV is for VIOLENCE/FANTASY VIOLENCE
S stands for SEXUAL CONTENT
L stands for strong LANGUAGE
D stands for suggestive DIALOG
34
AV-32S575\585 34
5/11/04, 10:27:46 AM
Initial Setup
Setting US V-Chip Ratings
Press the MENU button
π†
è
To V-CHIP
To operate (lock icon
V-CHIP
V-CHIP
appears)
Press ZERO to access the V-Chip menu
è
π†
è
To turn V-Chip ON or OFF
To move to SET US TV RATINGS
To operate
OFF
SET US TV RATINGS
SET MOVIE RATINGS
SET CANADIAN RATINGS ENG
SET CANADIAN RATINGS FRE
UNRATED
VIEW
SELECT
OPERATE
MENU
EXIT
Directions to set US V-Chip Ratings
Line up the cursor in the column (TV PG, TV G, etc.) with the content row (V/FV, S, etc.) and
press the π
† or √® to move the cursor to the correct location. Press OK to turn the locking
feature on or off. An item is locked if the
icon appears instead of a “—”.
For example. To block viewing of all TV 14 shows, move the cursor to the top row of that
column and add a lock icon. Once you’ve put a lock on the top row, everything in that column
is automatically locked.
π
†√® To the TV 14 Column
SET US TV RATINGS
Press the OK button to lock
TV
MA
TV
14
TV
PG
TV
G
TV
Y7
TV
Y
Press the MENU button when finished
V/FV
S
Note:
• If you want to change the setup, move the cursor to the top
column and change the lock icon to “—” by pressing OK
again. You may then select individual categories to block.
L
D
SELECT
OK
OPERATE
MENU
EXIT
35
AV-32S575\585 35
5/11/04, 10:27:47 AM
Initial Setup
Movies Ratings
❒ NR – Not Rated
This is a film which has no rating. In many cases these films were imported from countries
which do not use the MPAA ratings system. Other NR films may be from amateur producers
who didn’t intend to have their film widely released.
NR (Not Rated) Programming may contain all types of programming including children’s
programming, foreign programs, or adult material.
❒ G – General Audience
In the opinion of the review board, these films contain nothing in the way of sexual content,
violence, or language that would be unsuitable for audiences of any age.
❒ PG – Parental Guidance
Parental Guidance means the movie may contain some contents such as mild violence,
some brief nudity, and strong language. The contents are not deemed intense.
❒ PG-13 – Parents Strongly Cautioned
Parents with children under 13 are cautioned that the content of movies with this rating may
include more explicit sexual, language, and violence content than movies rated PG.
❒ R – Restricted
These films contain material that is explicit in nature and is not recommended for
unsupervised children under the age of 17.
❒ NC-17 – No One Under 17
These movies contain content which most parents would feel is too adult for their children
to view. Content can consist of strong language, nudity, violence, and suggestive or explicit
subject matter.
❒ X – No One under 18
Inappropriate material for anyone under 18.
Directions to set Movie (MPAA) Ratings
Press the MENU button
π†
è
To V-CHIP
To operate (Lock icon
appears)
Press ZERO to access V-Chip setup options
π†
è
To SET MOVIE RATINGS
To enter movies menu
For example:
To block viewing of X and NC-17 rated from shows:
SET MOVIE RATINGS
π
†√® To the X Column
Press the OK button to lock
X
NC17
R PG13 PG
G
π
†√® To the NC-17 Column
Press the OK button to lock
Press the MENU button to finish
NR
SELECT
OK
OPERATE
MENU
EXIT
36
AV-32S575\585 36
5/11/04, 10:27:47 AM
Initial Setup
Canadian V-Chip Ratings
❒ E – Exempt
Exempt programming includes: news, sports, documentaries and other information
programming, talk shows, music videos, and variety programming.
❒ C – Programming Intended for Children
Violence Guidelines: There will be no realistic scenes of violence. Depictions of aggressive
behavior will be infrequent and limited to portrayals that are clearly imaginary, comedic or
unrealistic in nature.
❒ C8+ – Programming Intended for Children 8 and Over
Violence Guidelines: Any realistic depictions of violence will be infrequent, discreet, of low
intensity and will show the consequences of the acts. There will be no offensive language,
nudity or sexual content.
❒ G – General Audience
Programming will contain little violence and will be sensitive to themes which could affect
younger children.
❒ PG – Parental Guidance
Programming intended for a general audience, but which may not be suitable for younger
children. Parents may consider some content not appropriate for children aged 8-13.
❒ 14+ – 14 Years and Older
Parents are strongly cautioned to exercise discretion in permitting viewing by pre-teens and
early teens. Programming may contain mature themes and scenes of intense violence.
❒ 18+ – Adult
Material intended for mature audiences only.
Directions to set Canadian V-Chip Ratings
Press the MENU button
π†
è
To V-CHIP
To operate (lock icon
appears)
Press ZERO to access V-Chip setup options
π†
è
To SET CANADIAN RATINGS ENG (for English)
To enter ratings menu
For example:
To block viewing of programming rated 14+ and 18+:
è
è
To the 18+ Column
Press the OK button to lock
SET CANADIAN RATINGS ENG
18+
PG
14+
G
C8
C
To the 14+ Column
Press the OK button to lock
Press the MENU button to finish
SELECT
OK
OPERATE
MENU
EXIT
37
AV-32S575\585 37
5/11/04, 10:27:48 AM
Initial Setup
Set Lock Code
Channel guard and V-Chip settings are protected by a four-digit lock code. Your TV comes preset with a lock code of “0000”. You may change the code to any four-digit number you wish. To
change the lock code, follow the steps below.
Press the MENU button
π†
è
To SET LOCK CODE
To operate (lock icon
SET LOCK CODE
LOCK CODE
0000
appears)
Press ZERO to access the lock code
The first digit will be highlighted
è
π†
PRESS
To select the number
To move to the next digit
SELECT
OK
TO FINISH
OPERATE
MENU
EXIT
Continue to follow these directions for all four numbers
Press the OK button to finish (your lock code is now set)
Press the MENU button when finished
When a viewer attempts to watch a blocked channel,
this message appears:
The channel will remain blocked until the correct lock
code is entered (see above for information on setting
your lock code).
THIS PROGRAMMING EXCEEDS
YOUR RATING LIMITS.
PLEASE ENTER LOCK CODE BY
10 KEY PAD TO UNLOCK IT.
NO. - - - -
Notes:
• After a power interruption you must reset the lock code.
• Write your lock code number down and keep it hidden from potential viewers.
• If you forget the lock code, a new code may be set using the steps listed above.
Auto Demo
This function lets you preview the many different viewing modes of your TV. It will cycle
through “Multi Screen Demo”, “Picture in Picture Demo”, the different “16:9” ratios and all of the
different “Video Status” modes.
Press the MENU button
π†
è
To AUTO DEMO
To turn AUTO DEMO ON or OFF
Note:
• To stop auto demo, press the MENU button, and select auto
demo by pressing the π† buttons, and turn it off by pressing
the è buttons. Press the MENU button to finish.
INITIAL SETUP
PREVIOUS
AUTO TUNER SETUP
CHANNEL SUMMARY
V-CHIP
SET LOCK CODE
AUTO DEMO
OFF
(4/4)
NEXT PAGE
SELECT
OPERATE
MENU
EXIT
38
AV-32S575\585 38
5/11/04, 10:27:48 AM
Initial Setup
Language
The language function is described on page 20 as the interactive plug-in menu. If you need to
choose the language again, follow the steps below.
Press the MENU button
π†
è
INITIAL SETUP
To LANGUAGE
To choose a language: ENG. (English), FRAN.
(French) or ESP. (Spanish)
PREVIOUS
LANGUAGE
AUTO SHUT OFF
OFF
Press the MENU button when finished
XDS ID
OFF
ENG. FRAN. ESP.
CLOSED CAPTION
TILT CORRECTION
(3/4)
NEXT PAGE
SELECT
OPERATE
MENU
EXIT
Closed Caption
Many broadcasts now include an onscreen display of dialog called closed captions. Some
broadcasts may also include displays of additional information in text form. Your television can
access and display this information using the closed caption feature. To activate the closed
caption feature, follow the steps below.
Press the MENU button
π†
è
è
π†
è
To CLOSED CAPTION
To operate
To select CAPTION or TEXT in MODE
To select CAPTION or TEXT
To select a caption (CC1 to CC4) or text
channel (T1 to T4)
Press the OK button to save
CLOSED CAPTION
MODE
CAPTION
TEXT
CC1
TEXT
T1
PRESS
SELECT
OK
TO FINISH
OPERATE
MENU
EXIT
Press the MENU button when finished
Notes:
• Closed caption subtitles are usually found on closed caption channel CC1. Some programs
may include additional text information which is usually found on text channel T1. The other
channels are available for future use.
• Closed captioning may not work correctly if the signal being received is weak or if you are
playing a video tape.
• Most broadcasts containing closed captioning will display a notice at the start of the program.
• To select the mode, press the C.C. button. See page 56.
39
AV-32S575\585 39
5/11/04, 10:27:49 AM
Initial Setup
Auto Shut Off
This function automatically shuts off your TV when there is no signal from the channel the
TV is on.
Press the MENU button
π†
è
INITIAL SETUP
PREVIOUS
LANGUAGE
To AUTO SHUT OFF
To turn ON or OFF
ENG. FRAN. ESP.
CLOSED CAPTION
Press the MENU button when finished
AUTO SHUT OFF
OFF
XDS ID
OFF
TILT CORRECTION
• If the channel that you have on does not receive a
signal for more than one minute, the blinking text
“NOT RECEIVING A SIGNAL AUTO SHUT OFF IN 9 MIN.”
appears on the screen, and starts the countdown. If no
signal is being received within 10 minutes, the TV shuts itself off.
NEXT PAGE
SELECT
(3/4)
OPERATE
MENU
EXIT
XDS ID
XDS ID Display provides a channel’s call letters, the network’s name, and even a program
name. The XDS ID information is provided by the broadcaster.
Press the MENU button
π†
è
To XDS ID
To turn ON or OFF
Press the MENU button when finished
INITIAL SETUP
PREVIOUS
ENG. FRAN. ESP.
LANGUAGE
CLOSED CAPTION
OFF
AUTO SHUT OFF
OFF
XDS ID
TILT CORRECTION
(3/4)
NEXT PAGE
SELECT
OPERATE
MENU
EXIT
Tilt Correction
This adjusts the pictures so that it looks even on the screen and not lopsided.
Press the MENU button
π†
è
è
To TILT CORRECTION
To enter
To adjust TILT CORRECTION
Press the MENU button when finished
INITIAL SETUP
PREVIOUS
LANGUAGE
ENG. FRAN. ESP.
CLOSED CAPTION
AUTO SHUT OFF
OFF
XDS ID
OFF
TILT CORRECTION
NEXT PAGE
SELECT
(3/4)
OPERATE
MENU
EXIT
40
AV-32S575\585 40
5/11/04, 10:27:49 AM
Initial Setup
Noise Muting
This feature inserts a blank blue screen over channels which are not broadcasting or are too
weak to be received clearly.
Press the MENU button
π†
è
To NOISE MUTING
To turn noise muting ON or OFF
Press the MENU button when finished
Note:
• Noise muting will not work during auto tuner setup or
when you operate channel summary.
INITIAL SETUP
PREVIOUS
ON
NOISE MUTING
OFF
FRONT PANEL LOCK
OFF
V1 SMART INPUT
VIDEO INPUT LABEL
NEXT PAGE
SELECT
(2/4)
OPERATE
MENU
EXIT
Front Panel Lock
This allows you to lock the keys on the front of the TV, so that a child may not accidentally
change your viewing preferences.
Press the MENU button
π†
è
To FRONT PANEL LOCK
To turn ON or OFF
Press the MENU button when finished
INITIAL SETUP
PREVIOUS
ON
NOISE MUTING
OFF
FRONT PANEL LOCK
OFF
V1 SMART INPUT
VIDEO INPUT LABEL
NEXT PAGE
SELECT
(2/4)
OPERATE
MENU
EXIT
You can turn off this feature in the following ways:
• Unplug the power cord, and plug it back in. Do this if your batteries die, or you lose your
remote control.
• Use the remote control.
• Press the MENU button on the front of the TV for more than 3 seconds. In this case, the OSD
for FRONT PANEL LOCK will appear.
Note:
• To turn ON/OFF the TV, press the POWER button for more than 3 seconds. This feature will
remain ON.
41
AV-32S575\585 41
5/11/04, 10:27:50 AM
Initial Setup
V1 Smart Input
This feature is used if you have connected an AV Receiver to your television. By turning this
feature on, your television can automatically detect the signal source from your components
that are connected to your AV Receiver.
Press the MENU button
π†
è
To V1 SMART INPUT
To turn ON or OFF
Press the MENU button when finished
Notes:
• If you do not have an AV Receiver connected to your
television, turn this feature OFF. By doing so, you can
take advantage of using AV CompuLink components
with your television.
• Some AV Receivers may not work with this function.
INITIAL SETUP
PREVIOUS
NOISE MUTING
FRONT PANEL LOCK
V1 SMART INPUT
ON
OFF
OFF
VIDEO INPUT LABEL
NEXT PAGE
SELECT
(2/4)
OPERATE
MENU
EXIT
Video Input Label
AV-32S575 ONLY
This function is used to label video input connections for
the onscreen displays.
Press the MENU button
π†
To VIDEO INPUT LABEL
è
To operate
π†
To select the desired video input
è
INITIAL SETUP
PREVIOUS
NOISE MUTING
FRONT PANEL LOCK
V1 SMART INPUT
VIDEO INPUT LABEL
To select the desired preset input label (see
chart below)
Press the OK button to save
Press the MENU button when finished
NEXT PAGE
SELECT
(2/4)
OPERATE
42
AV-32S575\585 42
VCR
You have a VCR connected to the video input
DVD
You have a DVD connected to the video input
D-VHS
You have a Digital VCR connected to the video input
STB
You have a Set-top Box connected to the video input
SAT
You have a Satellite Receiver connected to the video input
AMP
You have an Amplifier connected to the video input
GAME
You have a Video Game connected to the video input
CAM
You have a Video Camera connected to the video input
DISC
You have a Video Disc player connected to the video input
EXIT
VIDEO INPUT LABEL
VCR
DVD
SAT
GAME
STB
PRESS
Select when...
MENU
VIDEO-1
VIDEO-2
VIDEO-3
VIDEO-4
DIGITAL-IN
SELECT
Preset
Labels
ON
OFF
OFF
OK
TO FINISH
OPERATE
MENU
EXIT
5/11/04, 10:27:50 AM
Initial Setup
Digital-In
The DIGITAL-IN option can only be displayed in the INITIAL SETUP menu when a HDMI480p
picture signal is being input to the DIGITAL-IN terminal. This option adjusts the position when
a HDMI or DVI 480p picture signal is being displayed on the screen. There are two types of
HDMI480p picture signals: 640x480 and 720x480. If the displayed picture is slightly shifted, the
position can be adjusted by selecting either SIZE1 or SIZE2.
Press the MENU button
π†
To DIGITAL-IN
è
è
To enter
To select SIZE1 or SIZE2
Press the MENU button to finish
INITIAL SETUP
PREVIOUS
DIGITAL-IN
DIGITAL-IN AUDIO
CENTER CH INPUT
SIZE1
DIGITAL
ON
VARI
ON
AUDIO OUT
TV SPEAKER
NEXT PAGE
Note:
SELECT
(1/4)
OPERATE
EXIT
MENU
• The DIGITAL-IN menu can only be displayed when a HDMI or DVI 480p picture signal is
input to the Digital-In terminal and the picture is being displayed on the screen.
Digital-In Audio
This feature is used if you have a DTV or HDMI
compatible component connected to your TV.
Press the MENU button
π†
To DIGITAL-IN AUDIO
è
To select “ANALOG” or “DIGITAL”
Press the MENU button when finished
Notes:
INITIAL SETUP
PREVIOUS
DIGITAL-IN
DIGITAL-IN AUDIO
CENTER CH INPUT
AUDIO OUT
SIZE1
DIGITAL
ON
VARI
ON
TV SPEAKER
NEXT PAGE
SELECT
(1/4)
OPERATE
MENU
EXIT
• If your DTV or HDMI component is capable of digital audio and video, choose DIGITAL. If
your DTV or HDMI component is capable of analog audio and digital video, choose ANALOG.
• Refer to your DTV or HDMI component’s instruction manual for more information.
43
AV-32S575\585 43
5/11/04, 10:27:50 AM
Initial Setup
Center CH Input
When you are using a surround system, you can substitute the speaker of this television for
the center speaker of your surround system. Set CENTER CH INPUT to on when you use the
speaker as the center speaker of your surround system.
Press the MENU button
π†
è
INITIAL SETUP
To CENTER CH INPUT
To adjust CENTER CH INPUT to “ON” or “OFF”
PREVIOUS
DIGITAL-IN
DIGITAL-IN AUDIO
CENTER CH INPUT
Press the MENU button when finished
AUDIO OUT
TV SPEAKER
SIZE1
DIGITAL
ON
VARI
ON
NEXT PAGE
Note:
The normal speaker output is 20W 16Ω. The maximum is
40W. If you exceed the maximum, your speaker may break.
SELECT
(1/4)
OPERATE
MENU
EXIT
Audio Out
If your television is connected to an external speaker source, audio out gives you the option of
controlling the volume level with your TV’s remote control.
Press the MENU button
π†
è
INITIAL SETUP
To AUDIO OUT
To VARI or FIX
PREVIOUS
DIGITAL-IN
DIGITAL-IN AUDIO
Press the MENU button when finished
CENTER CH INPUT
AUDIO OUT
VARI: Lets you adjust the volume of the external speakers
using the VOLUME+/– buttons on your TV’s remote control.
FIX: The volume of the external speakers is adjusted
using the audio device’s remote control.
SIZE1
DIGITAL
ON
VARI
ON
TV SPEAKER
NEXT PAGE
SELECT
(1/4)
OPERATE
MENU
EXIT
TV Speaker
If your TV is connected to a stereo system, you can turn off the TV speakers and listen to the
audio through your stereo.
Press the MENU button
π†
è
To TV SPEAKER
To turn the TV’s speakers ON or OFF
Press the MENU button when finished
Notes:
INITIAL SETUP
PREVIOUS
DIGITAL-IN
DIGITAL-IN AUDIO
CENTER CH INPUT
AUDIO OUT
TV SPEAKER
SIZE1
DIGITAL
ON
VARI
ON
NEXT PAGE
SELECT
(1/4)
OPERATE
MENU
EXIT
• Before you turn the TV speaker setting from OFF
to ON, make sure that the TV volume level is low! If the TV volume is set too high, the
sound level will be extremely loud.
• After a power interruption, the TV speaker settings will return to “ON”.
44
AV-32S575\585 44
5/11/04, 10:27:51 AM
Picture Adjust
Picture Settings
These settings allow you to change and adjust the way the picture appears on your television.
TINT
Tint allows you to adjust the levels of red and green in your TV picture.
COLOR
The color function lets you make all the colors in the TV picture appear either more vivid or
subtle.
PICTURE
Picture allows you to adjust the levels of black and white on the TV screen, giving you a darker
or brighter picture overall.
BRIGHT
You can adjust the overall brightness of the TV picture with the Bright control.
DETAIL
The Detail feature adjusts the level of fine detail displayed in the picture.
Adjust the Picture Settings
Press the MENU button
π†
è
To TINT, COLOR, PICTURE, BRIGHT or
DETAIL
To enter
TINT
è
π†
+02
To adjust the setting
To move to the next setting
PICTURE ADJUST
STANDARD
PREVIOUS
TINT
COLOR
00
00
PICTURE 00
BRIGHT
00
DETAIL
00
COLOR TEMPERATURE
NEXT PAGE
SELECT OPERATE
LOW
(1/2)
MENU
EXIT
Press the MENU button when finished
Color Temperature
You can decide how strong or dull the colors appear on the TV screen.
Press the MENU button
π†
è
To COLOR TEMPERATURE
To enter
COLOR TEMPERATURE
è
LOW HIGH
To set LOW or HIGH
Press the MENU button when finished
PICTURE ADJUST
STANDARD
PREVIOUS
TINT
COLOR
00
00
PICTURE 00
BRIGHT
00
DETAIL
00
COLOR TEMPERATURE
NEXT PAGE
SELECT OPERATE
LOW
(1/2)
MENU
EXIT
45
AV-32S575\585 45
5/11/04, 10:27:51 AM
Picture Adjust
Digital Noise Clear
With digital noise clear, this helps take our static or noise from a channel that may not be
coming in clearly.
Press the MENU button
π†
è
π†
DIG. NOISE CLEAR
OFF
LOW
HIGH
To DIG. NOISE CLEAR
To enter
To select the mode “LOW”, “HIGH” or “OFF”
Press the MENU button when finished
(VSM) Velocity Scan Modulation
Velocity scan modulation circuitry varies the electron beam’s horizontal scanning speed to help
accentuate the differences in picture brightness to sharpen the edges of images.
Press the MENU button
π†
è
VSM
è
PICTURE ADJUST
To VSM
To enter
PREVIOUS
STANDARD
DIG. NOISE CLEAR
VSM
OFF
ON
NATURAL CINEMA
AUTO
ON OFF
To turn VSM ON or OFF
Press the MENU button when finished
RESET
NEXT PAGE
SELECT
(2/2)
OPERATE
MENU
EXIT
Natural Cinema
Natural cinema corrects the problem of blurred edges which may occur when viewing a program
originally shot on film (such as motion pictures) or animation. If you notice blurring at the edges
of these programs, choose NATURAL CINEMA and set it to AUTO. Natural Cinema helps correct
conversion errors that occur when film, which is shot at 24 frames-per-second, is broadcast at the
television rate of 30 frames-per-second.
Press the MENU button
π†
è
π†
NATURAL CINEMA
To NATURAL CINEMA
To enter
To select the mode “AUTO", "ON" or "OFF”
AUTO
ON
OFF
Press the MENU button when finished
Notes: The natural cinema mode is automatically set to “AUTO” in the following cases:
• Turning on or off
• Changing the channel or input mode
• Using multi-screen functions
46
AV-32S575\585 46
5/11/04, 10:27:52 AM
Picture Adjust
Reset
Reset resets all picture adjustments (tint, color, picture, bright, detail, color temperature, dig.
noise clear and VSM) at once to the default settings.
Press the MENU button
π†
è
To RESET
To enter
The onscreen menu disappears for a moment, and
then the settings are reset to the default setting for
all the picture adjustments.
Press the MENU button when finished
PICTURE ADJUST
PREVIOUS
STANDARD
DIG. NOISE CLEAR
VSM
NATURAL CINEMA
OFF
ON
AUTO
RESET
NEXT PAGE
SELECT
(2/2)
OPERATE
MENU
EXIT
47
AV-32S575\585 47
5/11/04, 10:27:52 AM
Sound Adjust
Sound Settings
These settings allow you to change and adjust the sound on your television.
BASS – You can increase or decrease the level of low-frequency sound in the TV’s audio with
the bass adjustment.
TREBLE – Use treble to adjust the level of high-frequency sound in your TV’s audio.
BALANCE – Adjust the level of sound between the TV’s left and right speakers with the
balance setting.
Adjust the Sound Settings
Press the MENU button
π†
è
π†
To BASS, TREBLE or BALANCE
To adjust the setting
To move to the next setting
Press the MENU button when finished
SOUND ADJUST
PREVIOUS
BASS
TREBLE
00
00
BALANCE
MTS
00
STEREO SAP MONO
RESET
NEXT PAGE
Notes:
SELECT
OPERATE
MENU
EXIT
• You can reset the sound adjustments (BASS, TREBLE
and BALANCE) you set at once as the default setting when you select reset. See page 47.
• You can adjust BALANCE only when A.H.S. is off. See page 54.
MTS (Multi-Channel Television Sound)
MTS technology allows several audio signals to be broadcast at once, giving you a choice
in what you wish to hear with a TV program. In addition to mono or stereo sound, an
MTS broadcast may also include a second audio program (SAP).
Press the MENU button
π†
è
To MTS
Select the mode
(The ON AIR arrow tells you if a broadcast is in stereo and/or
contains an SAP).
Press the MENU button when finished
SOUND ADJUST
PREVIOUS
BASS
TREBLE
00
00
BALANCE
MTS
00
STEREO SAP MONO
RESET
NEXT PAGE
Notes:
SELECT
OPERATE
MENU
EXIT
• Keep the TV in stereo mode to get the best sound quality. The sound will work in stereo
mode even if a certain broadcast is in mono sound only.
• Choose the mono setting to reduce excessive noise on a certain channel or broadcast.
• Selecting SAP will allow you to hear an alternative soundtrack, if one is available.
• MTS unavailable if your television’s input source is in input 1, 2, 3 or 4 mode, as described
on page 53.
Reset
Reset resets all Sound Adjustments (Bass, Treble and Balance) at once to the default settings.
See page 47 on how to use reset.
48
AV-32S575\585 48
5/11/04, 10:27:53 AM
Clock/Timers
Set Clock
The set clock function is described on page 21 as the interactive plug-in menu. You can choose
to set the clock automatically, or manually. If you need to set the clock again, follow the steps
below.
Press the MENU button
π†
To SET CLOCK
è
To operate
When you set the clock automatically, choose AUTO by pressing the
π†
To TIME ZONE
è
To select your time zone
ATLANTIC
SET CLOCK
EASTERN
HAWAII
√ or ® arrows.
CENTRAL
ALASKA
MOUNTAIN
PACIFIC
π†
To D.S.T. (daylight savings time)
è
To turn D.S.T. ON or OFF
MODE
TIME
TIME ZONE
D.S.T.
AUTO
-- : -- -ATLANTIC
ON
PRESS
SELECT
OK
TO FINISH
OPERATE
EXIT
MENU
Press OK to finish
Press the MENU button when finished
When you set the clock manually, choose MANUAL by pressing the
π†
To move to the hour
è
To set the hour
π†
To move to minutes
è
To set the minutes
Press OK to start clock
√ or ® arrows.
SET CLOCK
MODE
TIME
TIME ZONE
D.S.T.
MANUAL
-- : -- -ATLANTIC
ON
PRESS
THANK YOU !!
SELECT
OK
TO START CLOCK
OPERATE
MENU
EXIT
Press the MENU button when finished
Notes:
• D.S.T. can be used only for US and Canada when it is set to ON in the SET CLOCK menu.
• Only when the MODE set to AUTO, the Daylight Savings Time feature automatically adjusts
your TV’s clock for Daylight Savings. The clock will move forward one hour at 2:00 am on
the first Sunday in April. The clock will move back one hour at 2:00 am on the last Sunday in
October.
• You will have to reset the clock after a power interruption. You must set the clock before
operating any timer functions.
49
AV-32S575\585 49
5/11/04, 10:27:53 AM
Clock/Timers
On/Off Timer
The on/off timer lets you program your television to turn itself on or off. You can use it as an
alarm to wake up, to help you remember important programs, or as a decoy when you’re not
home.
Press the MENU button
π†
To ON/OFF TIMER
è
è
To operate (begins with ON TIME)
To set the hour (AM/PM) you want the TV to turn on
†
To move to minutes
è
To set the minutes
ON/OFF TIMER
7:00 PM
ON TIME
10:00 PM
OFF TIME
CHANNEL
03
CURRENT
EVERYDAY
ON VOLUME
MODE
NO
ON/OFF TIMER
PRESS
SELECT
OK
TO FINISH
OPERATE
†
To accept ON TIME and move to OFF TIME (the
time the TV will turn off). Set the OFF TIME the same way as ON TIME
†
To accept OFF TIME and move to CHANNEL
è
To select channel
†
To ON VOLUME
è
†
è
†
è
MENU
EXIT
To set the volume level
To move to MODE
Choose ONCE or EVERYDAY
To ON/OFF TIMER
Choose YES to accept the timer setting, choose NO if you don’t wish to accept
Press the OK button to finish
Press the MENU button to exit the menu
Notes:
• The on/off time cannot be set to locked or guarded channels.
• In order for the on/off timer to work, the clock must be set.
• After a power interruption, the timer settings must be reset.
50
AV-32S575\585 50
5/11/04, 10:27:54 AM
Button Functions
Multi Screen Function
Your television has two kinds of screen: PIP and INDEX (9 channels).
Note: After you press any multiscreen button, if you press the menu button, only the picture
adjust screen will appear.
Twin
Turn PIP on by pressing the TWIN button
Twin
07
02
TWIN
Each press of TWIN will shift the PIP window to a different corner and turn off.
TWIN
TWIN
TWIN
TWIN
"PIP OFF"
TWIN
Note:
• You cannot select the component input in the PIP mode. (Except if the input is a 525i
component signal).
• When you select the AUTO TUNER SETUP, CHANNEL SUMMARY, V-CHIP, the PIP window
turns off.
51
AV-32S575\585 51
5/11/04, 10:27:54 AM
Button Functions
Index
This allows you to quickly look at up to 9 channels at a time so that you can decide which one
to watch.
1
2
3
4
5
6
7
8
9
Notes:
• Only RF input signal will be displayed.
• You can watch the channel added in channel summary. See page 30.
Freeze
Pressing the FREEZE button causes the screen to change to the PIP screen display with the still
picture displayed on the right. In order to return to the normal display, press the FREEZE button
once again.
Swap
You can exchange the channel (or input) displayed in the PIP window for the main screen
image by pressing the SWAP button.
Select
With SELECT, you can select the picture (channel) while viewing PIP screen. When you press
SELECT button, the channel number on the top will be highlighted. Each press of SELECT will
shift the channel.
52
AV-32S575\585 52
5/11/04, 10:27:54 AM
Button Functions
Power
Turns the TV on or off.
Press the POWER button
Number Buttons - 10Key Pad
Use the number buttons on the remote control to move directly to a specific channel. For
example, to move to channel 12:
0 (ZERO)
1 (ONE)
2 (TWO)
Tune
Lets you decide the input channel and select it. After you press the number buttons on the
remote, press the TUNE button. For example, to move to channel 12:
1 (ONE)
2 (TWO)
Press the TUNE button
Input
Selects the signal input source for the television: Input-1, 2, 3, 4 or DIGITAL-IN for video
devices like VCR’s DVD players, or camcorders.
Press the INPUT button
By every press of the INPUT button, you can change the input mode.
Notes:
• When you return to TV mode, press the RETURN+ button or direct 10 key pad.
• You can also access the FRONT CONTROL PANEL screen by using the MENU button on
the front of the TV instead of the remote control. It appears between INITIAL SETUP and
PICTURE ADJUST screen, and it has INPUT, VIDEO STATUS and ASPECT menus. Choose
INPUT by pressing Menu† on the front panel and choose a mode by using the CHANNEL+/buttons ( √ OPERATE ® ).
Channel +/–
Use these buttons to move up or down all the available channels your TV is able to receive.
Volume +/–
Use these buttons to raise or lower the TV’s volume level.
53
AV-32S575\585 53
5/11/04, 10:27:55 AM
Button Functions
Return +
The Return+ button has two functions:
Return - Returns to the channel viewed just before the channel currently onscreen.
Return+ - Lets you program a specific channel to return to while scanning through the
channels using the CH+ and CH– buttons.
RETURN+ and hold for three seconds
RETURN CHANNEL
PROGRAMMED!
The channel currently active has been programmed as your return+ channel. Now scan
through the channels using the CHANNEL+/- buttons.
RETURN+
You will return to your programmed channel.
• To cancel your return+ channel, press and hold the RETURN+ button for three seconds. The
message “RETURN CHANNEL CANCELLED!” will appear.
• Return+ works only with the CHANNEL+/- buttons. Pressing any number key will cancel
return+.
Sound
By pressing the SOUND button, you can change the A.H.S. (Advanced Hyper Surround) mode,
BBE, and SMART SOUND on or off.
A.H.S. - Adds a more spacious surround sound. Music gives basic effect and movie for more
effect.
BBE - BBE High Definition Sound restores clarity and presence for better speech intelligibility
and musical realism.
SMART SOUND - Decreases high sound levels, giving a regulated sound level.
Press the SOUND button
π†
è
To select A.H.S., BBE or SMART SOUND
To choose the setting
Press the MENU when finished
SOUND EFFECT
A.H.S.
MOVIE MUSIC OFF
BBE
ON OFF
SMART SOUND
ON OFF
SELECT
OPERATE
MENU
EXIT
Note: Manufactured under license from BBE Sound, Inc. Licensed by BBE Sound,
Inc. under USP4638258, 5510752 and 5736897. BBE and BBE symbol are registered
trademarks of BBE Sound, Inc.
Muting
The MUTING button instantly turns the volume down completely when you press it. Press
MUTING and the volume level will instantly go to zero. To restore the volume to its previous
level, press MUTING again.
54
AV-32S575\585 54
5/11/04, 10:27:55 AM
Button Functions
Video Status
The Video Status button gives you a choice of four TV picture display settings, including a
display of your own preferences.
Standard - Resets the picture display to the factory settings.
Dynamic - Gives a vivid picture with better contrast when viewing in
a brightly lit room.
VIDEO STATUS
STANDARD
DYNAMIC
THEATER
GAME
Theater - Gives a rich, film-like look to video when viewing in a
dimly lit room.
Game - Used for when you are playing video games connected to
your TV.
Press the VIDEO STATUS button
By every press of the VIDEO STATUS button, you change the mode.
Note:
• You can also change the mode by pressing the π† buttons.
• You can also access the FRONT CONTROL PANEL screen by using the MENU button on
the front of the TV instead of the remote control. It appears between INITIAL SETUP and
PICTURE ADJUST screen, and it has INPUT, VIDEO STATUS and ASPECT menus. Choose
VIDEO STATUS by pressing Menu† on the front panel and choose a mode by using the
CHANNEL+/- buttons ( √ OPERATE ® ).
TheaterPro D6500K
The TheaterPro D6500K color temperature technology function makes sure that the video you
watch is set to the standard color temperature, so that what you see is as true to what the film
to video editors intended it to be.
Press the THEATERPRO button
Sleep Timer
The Sleep Timer can turn the TV off for you after you fall asleep. Program it to work in intervals
of 15 minutes, for a total time of up to 180 minutes.
Press the SLEEP TIMER button
0 15 30 45 60 75 90 105 120 135 150 165 180
Sleep Timer Message
20 seconds before the automatic shutoff, this message will appear:
GOOD NIGHT!!
PUSH SLEEP TIMER BUTTON
TO EXTEND
You then have 20 seconds to press the SLEEP TIMER button to
delay the shut off for another 15 minutes.
55
AV-32S575\585 55
5/11/04, 10:27:55 AM
Button Functions
Display
The display screen shows the current status of timers, inputs, and XDS ID.
Press the DISPLAY button
The screen to the right shows the following information:
The current channel or AV input (Channel 05)
The current time (12:20 pm)
Sleep timer status/minutes remaining (The Sleep Timer is off)
On/off timer status (Set to turn on everyday at 7:00 PM, off at
10:00 PM)
• Each Press of the DISPLAY button changes the display mode:
•
•
•
•
Display
Time
05 KLVX PBS
JAZZ FESTIVAL
NOW
SLEEP TIMER
ON/OFF TIMER
ON TIME
OFF TIME
Channel
12:20 PM
OFF
EVERYDAY
7:00 PM
10:00 PM
Off
Display - Full screen shown above
Time - Shows the current time only
Channel - Shows the current channel
Off - Turns display off
Notes:
• You may also turn off the display at any step by pressing MENU.
• If the clock, sleep timer or on/off timer are not set, the display screen will show:
“CLOCK NOT SET”, “SLEEP TIMER OFF”, and “ON/OFF TIMER OFF” respectively.
C.C. (Closed Caption)
Use the C.C. (Closed Caption) button to select the mode of closed caption.
Press the C.C. button
AV-32S585 ONLY
OFF
SMART CAPTION
ON
AV-32S575 ONLY
OFF
ON
• Smart Caption will appear when you press the Muting button, only on channels where the
broadcast contains closed captioning. (AV-32S585 ONLY)
• When you select ON, it will be the mode selected in the Closed Caption Menu.
• See page 39 when you set the caption/text mode.
56
AV-32S575\585 56
5/11/04, 10:27:56 AM
Button Functions
Aspect
This feature will help you adjust the picture you are watching to give you the best possible
picture quality.
Aspect Ratios
4:3 - Use this aspect mode when you
are watching a 4:3 broadcast.
16:9 - If you select 16:9 aspect mode
while watching a 4:3 broadcast, this
will stretch the picture so as to fit into
the 16:9 format. When you select this
mode, black bars will appear on the top
and bottom of the TV screen.
16:9 - Use this aspect mode when you
are watching a 16:9 broadcast. This
is also referred to as "widescreen", for
example on a DVD disc. When you
select this mode, black bars will appear
on the top and bottom of the TV screen.
HD ZOOM - If you are watching a 4:3
high definition broadcast and you select
this aspect mode, it will zoom in on the
picture.
V STRETCH - If you are watching a 4:3
broadcast, this aspect mode will stretch
the picture vertically on your TV
57
AV-32S575\585 57
5/11/04, 10:27:56 AM
Button Functions
Aspect Ratios (Continued)
Press the ASPECT button
• By pressing the ASPECT button, you can change the size.
When you change the aspect ratios, it is different from their broadcast or recorded program.
NTSC, 480i, 480p
HD (1080i, 720p)
ASPECT
ASPECT
4:3
16:9
16:9
HD ZOOM
V STRETCH
Notes:
• You can also choose the size by pressing the π† buttons.
• When you change the aspect ratio or signal, reset the picture position to center.
Menu
The Menu button allows you to access JVC’s onscreen menu system. Press MENU to activate
the onscreen menu system.
• See individual topics like “Sound Adjust” for specific information on using menus.
OK
This button confirms your selection when you are in one of the onscreen menus.
Back
This button allows you to go back in the menu to change a selection or correct a mistake.
58
AV-32S575\585 58
5/11/04, 10:27:57 AM
Button Functions
TV/CATV Slide Switch
Use either the television’s own tuner or a cable box to select channels. Set this switch to TV to
operate the television’s built-in tuner. Move the switch to CATV to operate a cable box.
Note:
• See page 23 for information on programming your remote for cable box operation.
VCR/DVD Slide Switch
You can control a VCR or DVD player with the buttons on the lower part of the remote control.
Move the slide switch to VCR or DVD to operate.
Notes:
• The remote is preset with the code 000 to control JVC-brand VCR’s. For any other
manufacturer’s brand VCR, please see the code chart and instructions on page 24.
• The remote is preset with the code 000 to control JVC-brand DVD players. For any other
manufacturer’s brand DVD player, please see the code chart and instructions on page 25.
VCR Buttons
You can use this remote control to operate the basic functions of your VCR. These functions
include: play, record, rewind, fast-forward, stop, pause, channel scan, TV/VCR, power on, and
power off.
Move the selector switch to VCR to operate.
• The remote is preset with the code 000 to control JVC-brand VCR’s. For any other
manufacturer’s brand VCR, please see the code chart and instructions on page 24.
DVD Buttons
You can also use this remote control to operate the basic functions of your DVD player. These
functions include: play, rewind, fast-forward, stop, still/pause, previous/next, tray open/close,
power on, and power off.
Move the selector switch to DVD to operate.
• The remote is preset with the code 000 to control JVC-brand DVD players. For any other
manufacturer’s brand DVD player, please see the code chart and instructions on page 25.
Light
All remote control buttons are illuminated, except for the TV/CATV slide switch, VCR/DVD slide
switch and LIGHT button. Press the LIGHT button to turn the illumination on for 4 seconds.
59
AV-32S575\585 59
5/11/04, 10:27:57 AM
Troubleshooting
PROBLEMS
CHECK
There is no power
• See if the power cord became unplugged.
• Check for a blown fuse or circuit breaker or a power outage.
There is no picture
or sound
• The antenna could be disconnected.
• The input mode could be set improperly. See page 53.
• The tuner (Auto Tuner Setup) could be set improperly. See page 30.
• The TV station may be having difficulties. Check to see if other stations are working.
Remote control is not
operating properly or
at all
• Check to see that the batteries are still working and properly installed.
• Make sure the remote has a clear sight path to the TV.
• Check that the TV/CATV switch is in the proper position.
• You may be too far from the TV. You must be within 23 feet (7 meters).
You cannot select a
certain channel
• Make sure the channels have been programmed. See "Channel Summary", page 30.
• Check to see if the channel is locked. See "Channel Summary - Lock" page 31.
The power turns off
by itself
• Make sure the set did not become unplugged.
• Perhaps the On/Off Timer is set. See page 50.
• Check to see if the Sleep Timer was set. See page 55.
The clock is wrong
• The power was interrupted and the clock was not reset. See page 49.
The color quality
is poor
• Tint and Color may be improperly adjusted. See page 45.
• The Video Status mode may be turned to the wrong setting. See page 55.
There are lines
across the picture
• There could be interference from another electrical appliance, such as a computer,
another TV or VCR. Move any such appliances further away from the TV.
The picture is spotted
• There could be interference from a high-wattage appliance, like a hairdryer or vacuum,
operating nearby. Move the antenna away from the appliance or change to a coaxial
cable connection which is less prone to interference.
There are double
pictures (ghosts)
• A building or passing airplane can reflect the original signal and produce a second,
slightly delayed one. Adjust your antenna position.
Picture is snowy
(image noise)
• Your antenna may be damaged, disconnected or turned. Check the antenna
connection. If the antenna is damaged, replace it.
Screen is 40% black
• The Closed Caption Text mode is on. Turn it off in the Closed Caption Menu, page 39.
Stereo or bilingual
programs can't be
heard
• Make sure the MTS settings are correct. See "MTS" on page 48.
There is no sound
from the TV's
speaker
• The Center CH Input may be turned on. See page 44.
Static electricity
• It is normal to feel static electricity if you brush or touch the screen.
You hear occasional
crackling sounds
• It is normal for the TV to make crackling sounds when first turned on or off. Unless
the sound or picture become abnormal, this is fine.
60
AV-32S575\585 60
5/11/04, 10:27:57 AM
61
AV-32S575\585 61
5/11/04, 10:27:58 AM
62
AV-32S575\585 62
5/11/04, 10:27:58 AM
Specifications
MODEL
AV-32S585
AV-32S575
Reception
Format
NTSC, BTSC System (Multi-Channel Sound)
Reception
Range
VHF 2 to 13, UHF 14 to 69
Sub Mid, Mid, Super, Hyper and Ultra bands
(181 channel frequency synthesizer system)
Power Source
AC 120V, 60Hz
Power
Consumption
215W
Screen Size
32 inch / 80 cm
measured diagonally
4:3 Ratio
Audio Output
10W + 10W
Speakers
2 1/2 x 5 inch / 6.5 x 13 cm oval x 2
Antenna
Terminal
75 ohms (VHF/UHF) (F-type connector)
External Input
Jacks
Video: 1 Vp-p, 75 ohms
Audio: 500mVrms (-4dBs) high impediance
S-Video Input
Jack
Y: 1Vp-p positive, 75 ohms (negative sync provided)
C: 0.286 Vp-p (burst signal), 75 ohms
Component
Input Jacks
Y: 1Vp-p positive, 75 ohms (negative sync provided)
PB/PR: 0.7 Vp-p, 75 ohms
Audio Output
Jacks
(VARI/FIX)
VARI: More than 0 to 1000mVrms (+2.2dBs)
FIX: 500 mVrms (-4dBs) Low impedance
(400 Hz when modulated 100%)
Subwoofer
Output Jack
More than 0 to 1000mVrms (+2.2 dBs)
Low impedance (100 Hz when modulated 100%)
AV Compu Link
III Jack
Digital–In
3.5 mm mini jack x 1
HDMI jack x 1
Note: The Digital–In terminal is not compatible with picture signals of a
personal computer
Dimensions (In)
WxHxD (cm)
37 x 27 x 22 1/2
93.9 x 68.5 x 57.0
Weight (lbs / kg)
143 / 65
Accessories
Remote control unit x 1 / AA batteries x 2
Specifications subject to change without notice.
Note:
• Reception of channel A-5 ("95" of the TV set's on-screen cable channel numbers) is not
recommended for your TV set.
63
AV-32S575\585 63
5/11/04, 10:27:58 AM
JVC COMPANY OF AMERICA
Division of JVC Americas Corp.
1700 Valley Road
Wayne, New Jersey, 07470
AV-32S575\585 64
JVC CANADA, INC.
21 Finchdene Square
Scarborough, Ontario
Canada, M1X 1A7
5/11/04, 10:27:58 AM
Download PDF