Honda HP400BA Owner's Manual 64 Pages

Honda HP400BA is a powerful and versatile power carrier designed for hauling loads in various applications. Its track drive system provides excellent traction on uneven terrain, while the adjustable carrier bed allows for easy loading and unloading. The Honda HP400BA is equipped with various safety features such as a brake and steering clutch levers and tie-down hooks for securing loads.

advertisement

Ask Al about Honda HP400BA Owner's Manual

Chatbot has read manual and is ready to answer your questions.

Honda HP400BA Owner's Manual - HP400BA Power Carrier | Manualzz
Owner’s
Manual
Power Carrier
HP400
I I
01997
American
Honda
Motor Co., Inc. -
All Rights Reserved
I I I I I
Thank you for purchasing a Honda power carrier. We want to help you get the best
results from your new power carrier and to operate it safely. This manual contains the
information on how to do that; please read it carefully.
This owner’s manual describes the operation and maintenance of the HP400 power
carrier. All information in this publication is based on the latest product information
available at the time of printing.
Honda Motor Co., Ltd. reserves the right to make changes at any time without notice
and without incurring any obligation. No part of this publication may be reproduced
without written permission.
This manual should be considered a permanent part of the power cat-tierand should
remain with it if it is resold.
Safety Messages
Yoursafetyandthesafetyofothersisveryimpoltant.Wehaveprovidedimportantsafety
messages in this manual and on the power carrier. Please read these
messages carefully.
A safety message alerts you to potential hazards that could hurt you or others. Each
safety message is preceded by a safety alert symbol a and one of three words:
DANGER, WARNING, or CAUTION.
These mean:
B
You WILL be KILLED or SERIOUSLY HURT if you don’t follow
instructions.
m
You CAN be KILLED or SERIOUSLY HURT if you don’t follow
instructions.
w
You CAN be HURT if you don’t follow instructions.
Each message tells you what the hazard is, what can happen, and what you can do
to avoid or reduce injury.
Damage Prevention
Messages
You will also see other important messages that are preceded by the word NOTICE.
This word means:
pi?EEq
Your power carrier or other property could be damaged if you
don’t follow instructions.
The purpose of these messages is to help prevent damage to your power carrier other
property, or the environment.
1
CONTENTS
3
SAFETY ...........................................................................................................................
3
SAFETY LABEL LOCATIONS ................................................................................
.4
SAFETY INFORMATION .......................................................................................
.5
2. COMPONENT IDENTIFICATION..
.................................................................................
6
3. CONTROLS .....................................................................................................................
.6
.:. .......................................
Fuel Valve ....................................................................
y
Engine Switch .........................................................................................................
Throttle Lever. .........................................................................................................
.7
Starter Grip .............................................................................................................
t
Gear Shift Lever ....................................................................................................................................
Drive Clutch Levers.
9
Steering Clutch Levers ............................................................................................
9
Carrier Bed Release Lever ......................................................................................
4. PRE-OPERATION
CHECK ..........................................................................................
.10
10
Fuel .......................................................................................................................
13
Engine Oil.. ............................................................................................................
14
Air Cleaner ........ ....................................................................................................
15
Carrier Extension Pipe Lock Bolts .........................................................................
;i
5. STARTING THE ENGINE .............................................................................................
6. OPERATION .................................................................................................................
High Altitude Operation ........................................................................................
.21
22
7. STOPPING THE ENGINE .............................................................................................
...................................................................................................
25
8. CARRYING LOADS ...
25
Load Carrying Safety ............................................................................................
26
Tie-Down Hooks ....................................................................................................
.27
Carrier Side Plate and Carrier Front Plate ...........................................................
28
Dumping Loads .....................................................................................................
29
Load Carrying Capacity .........................................................................................
.30
Carrier Bed Support Bar.. .....................................................................................
...........................................................................................................
.31
9. MAINTENANCE
The Importance of Maintenance ...........................................................................
z;
Maintenance Safety ..............................................................................................
$
Proper Maintenance is the Owner’s Responsibility ...............................................
Maintenance Schedule .............................. . ...........................................................
Tool Kit ..................................................................................................................
3:
Engine Oil Change ................................................................................................
;;
Spark Plug Service ................................................................................................
Air Cleaner Service ...............................................................................................
.41
Adjusting the Track Tension .................................................................................
42
Adjusting the Drive Clutch Cable ..........................................................................
Adjusting the Brake Cable. ....................................................................................
ii
Checking Brake Wear ...........................................................................................
.45
Adjusting the Steering Clutch Cable ....................................................................
.46
Adjusting the Dumping Lock Cable ......................................................................
.47
Checking the Transmission Oil ............................................................................
.47
Checking the Clutch Oil ........................................................................................
48
Spark Arrester Service (Optional part) .................................................................
.49
Lubrication.. ..........................................................................................................
.50
Temporary Installation of a Disengaged Track ....................................................
.52
10. TRANSPORTING/STORAGE
......................................................................................
.54
11. TROUBLESHOOTING
.................................................................................................
.55
12. SPECIFICATIONS
........................................................................................................
.56
13. WARRANTY SERVICE INFORMATION ......................................................................
57
14. INDEX.. ..........................................................................................................................
1.
2
1. SAFETY
SAFETY LABEL LOCATIONS
The labels shown here contain important safety information. Please read them
D
carefully.
These labels are considered permanent parts of your power carrier, so if a
label comes off or becomes hard to read, contact your authorized Honda
power carrier dealer for a replacement.
v’”
SUAFAk 88
REFER TO OWNERS
i i6ij
MANUAL FOR DETAILS.
IMPORTANT SAFETY INFORMATION
Most accidents with power carriers can be prevented if you follow all instructions in this manual and on the power carrier. The most common hazards are
discussed below, along with the best way to protect yourself and others.
. Honda power -carrieis ate designed togive safe and dependable service if
operated according to instructions. Read and understand the Owner’s
Manual before operating the power carrier. Failure to do so could result in
personal injury or equipment damage.
. Keep children and pets away from the area of operation to avoid possible
injury from contact with the power carrier.
. To avoid accidents or loss of control, do no ride on the power carrier; walk
behind, and hold both handlebars firmly. Do not allow others to ride on the
power carrier as passengers.
. Watch for obstacles while operating the power carrier. Do not use the power
carrier when visibility is poor. Under conditions of poor visibility, there is a
greater risk of striking an obstacle.
. To avoid accidents or overturning, observe the load limits described on
Page 29. Be sure the load is secure and does not protrude from the power
carrier or block visibility.
. To avoid overturning, be careful when changing the direction of the power
carrier while operating it on slopes, and do not operate the power carrier on
upward slopes greater than 15” or downward slopes greater than 15”.
. When operating the power carrier in reverse gear and walking backward,
there is greater risk of slipping or tripping. Be especially careful when
backing up.
. Know how to stop the power carrier quickly, and understand the operation
of all controls. Never permit anyone to operate the power carrier without
proper instruction.
. Gasoline is extremely flammableand isexplosive under certain conditions.
Allow the engine to cool before refueling. Refuelinawellventilatedarea
with the engine stopped. Do not smoke or allow flames or sparks in the
refueling area or where gasoline is stored.
. Do not overfill the fuel tank After refueling, make sure the fuel tank cap is
closed properly and securely.
. Be careful not to spill fuel when refueling. Fuel vapor or spilled fuel may
ignite. lf any fuel is spilled, make sure the area is dry before starting the
engine.
. Never run the engine in an enclosed or confined ama. Exhaust contains
poisonous carbon monoxide gas; exposure may cause loss of consciousness and may lead to death.
. The mufffer becomes very hot during operation and remains hot for a while
after stopping the engine. Be careful not to touch the muffler while it is hot.
Toavoidsevere burnsorfire hazards,lettheenginecoolbeforetranspotting
4 the power carrier or storing it indoors.
2. COMPONENT IDENTIFICATION
THROTTLE LEVER
ENGINE OIL FILLER CAP
TRACK
DRIVE CLUTCH LEVERS
STEERING CLUTCH LE
GEAR SHIFT LEVE
RIER BED RELEASE LEVER
ROD
VALVE
*Record the frame and engine serial numbers for your reference. Refer to the
serial numbers when ordering parts, and when making technical or warranty
inquiries (see page 56).
Frame serial number:
Engine serial number:
5
3. CONTROLS
Fuel Valve
The fuel valve opens and closes the fuel line leading from the fuel tank to the
carburetor.
Make sure that the valve
is positioned
exactly
at
either the ON or OFF position. When the power carrier is not’in use, always
leave the fuel valve in the OFF position to reduce the possibility of fuel
leakage.
FUEL VALVE
Engine Switch
The engine switch controls the electrical circuit for the spark plug ignition
system and must be turned to the ON position to enable the engine to start and
run. The engine will stop when the engine switch is turned to the OFF position.
When the power carrier is not in use always leave the engine switch in the OFF
position to prevent accidental starting.
ENGINE SWliCH
Choke Rod
The choke rod opens and closes the choke valve in the carburetor.
The CLOSE position enriches the fuel mixture for starting a cold engine.
The OPEN position provides the correct fuel mixture for operation after
starting and for restarting a warm engine.
CHOKE ROD
i
I
I
Throttle Lever
Use the throttle lever to select engine speed. In normal operation,
FAST position.
THROl-fLE
use the
LEVER
FAST
Starter Grip
Pull this grip to start the engine.
See page 24 for starting procedures.
STARTER GRIP
7
Gear Shift Lever
Use the gear shift lever to select drive speed or direction. Shift gears with the
engine running and the drive clutch levers released.
N
E!
m
1
N: NEUTRAL
1: LOW SPEED
2: HIGH SPEED
R: REVERSE
R
Drive Clutch Levers
Use the drive clutch levers to propel or stop the power carrier. The two levers
are connected and move simultaneously.
When the levers are held down
against the handlebars, this releases the brake and engages the drive: the
power carrier will move if the transmission is in gear. When the levers are
released, this disengages the drive and applies the brake: the power carrier
will stop.
DRIVE CLUTCH LEVERS
RUN
Steering Clutch Levers
Use the steering clutch levers to steer the power carrier. Pull up the right lever
to steer right. Pull up the left lever to steer left.
Carrier Bed Release Lever
Pull the release lever to unlock the carrier bed when you wish to tilt the bed for
dumping a load. With the carrier bed unlocked, tilt it by lifting the handlebar.
To lock the carrier bed again, push down firmly on the handlebar.
m
Before operating the power carrier check that the carrier bed
is locked. If the carrier bed is not locked, it may tilt while going downhill
and accidentally dump the load, which may cause personal injury and
property or equipment damage.
UNLOCK
CARRIEi BED
RELEASE LEVER
LOCK
HkNDLEBAR
9
4. PRE-OPERATION CHECK
Fuel
Refueling
Fuel tank capacity: 1.6 &?(1.68 US gal, 1.41 Imp gal)
Check the fuel level, and refill the tank if the fuel level is low.
Gasoline is highly flammable and explosive.
You can be burned or seriously
injured when handling fuel.
Stop the engine and keep heat, sparks, and flames away.
Handle fuel only outdoors.
l Wipe up spills
immediately.
l
l
Refuel in a well-ventilated
area before starting the engine. If the engine
has been running, allow it to cool. Refuel carefully to avoid spilling fuel.
Do not overfill: there should be no fuel in the filler neck. After refueling,
tighten the fuel tank cap securely.
Never refuel the power carrier inside a building where gasoline fumes
may reach flames or sparks. Keep gasoline away from appliance pilot
lights, barbeques, electric appliances, power tools, etc.
Spilled fuel is not only a fire hazard,
Wipe up spills immediately.
it causes
environmental
damage.
Fuel can damage paint and plastic. Be careful not to spill fuel when filling
your fuel tank. Damage caused by spilled fuel is not covered under
warranty.
FILLER NECK
10
Fuel Recommendations
Use unleaded gasoline with a pump octane rating of 86 or higher.
This engine is designed to operate on unleaded gasoline. Unleaded gasoline
produces fewer engine and spark plug deposits and extends exhaust system
life.
Never use stale or contaminated gasoline or an oil/gasoline
getting dirt or water in the fuel tank.
mixture. Avoid
Occasionally
you may hear a light “spark
knock”
or “pinging”
(metallic rapping noise) while operating under heavy loads. This is no cause
for concern.
If spark knock or pinging occurs at a steady engine speed, under normal
Joad, change brands of gasoline. If spark knock or pinging persists, see an
authorized Honda servicing dealer.
1 NOTICE
1
Running the engine with persistent
engine damage.
Running the engine
and the Distributor’s
by misuse.
spark knock or pinging can cause
with persistent spark knock or pinging is misuse,
Limited Warranty does not cover parts damaged
11
Oxygenated
Fuels
Some conventional gasolines are being blended with alcohol or an
ether compound. These gasolines are collectively referred to as oxygenated fuels. To meet clean air standards,
some areas of the
United States and Canada use oxygenated
fuels to help reduce
emissions.
If you use an oxygenated fuel, be sure it is unleaded
minimum octane rating requirement.
and meets the
Before using an oxygenated
fuel, try to confirm the fuel’s contents.
Some states/provinces
require this information
to be posted on the
pump.
The following are the EPA-approved
percentages
of oxygenates:
ETHANOL __
(ethyl or grain alcohol) 10% by volume
You may use gasoline containing up to 10% ethanol by
volume. Gasoline containing ethanol may be marketed
under the name “Gasohol”.
MTBE
(Methyl Tertiary Butyl Ether) 15% by volume
You may use gasoline containing up to 15% MTBE by
volume.
METHANOL--
(methyl or wood alcohol) 5% by volume
You may use gasoline containing
up to 5% methanol
by volume, as long as it also contains cosolvents and
corrosion inhibitors to protect the fuel system. Gasoline containing
more than 5% methanol by volume
may cause starting and/or performance
problems. It
may also damage metal, rubber, and plastic parts of
your fuel system.
If you notice any undesirable operating symptoms,
station, or switch to another brand of gasoline.
try another
service
Fuel system damage or performance problems resulting from the use
of an oxygenated
fuel containing
more than the percentages
of
oxygenates mentioned above are not covered under warranty.
12
Engine Oil
Inspection:
With the power carrier on a level surface, remove the oil filler cap and wipe
the dipstick clean. Insert the dipstick into the filler neck, but do not
screw it in. Remove the dipstick and check the oil level.
If the level is low, fill to the upper limit mark with the recommended
oil.
;MP.2C
I
30
80
I
-20
1
-10
I
0
I
10
I
20
1OO.F
I
,
10 4O'C
AMBIENT TEMPERATURE
Recommended oil
Use 4-stroke motor oil that meets or exceeds the requirements for API
service classification SF or SG. Always check the API SERVICE label on
the oil container to be sure it includes the letters SF or SG.
SAE low-30 is recommended for general use. Other viscosities shown
in the chart may be used when the average temperature in your area is
within the indicated range.
l
l
Using nondetergent oil can shorten the engine’s
using 2-stroke oil can damage the engine.
service
life, and
Running the engine with a low oil level can cause engine damage.
13
Air Cleaner
1. Remove the two wing nuts to remove the air cleaner cover.
2. Remove and inspect the air cleaner elements. If ihe elements are dirty,
follow the cleaning procedure described on page 40.
3. Reinstall the air cleaner elements, cover and wing nuts. Securely tighten
the wing nuts.
11
Never run engine without the air cleaner. Rapid engine wear
will result from contaminants,
such as dust and dirt, being drawn
through the carburetor, into the engine.
WING NUTS
A
AIR CLEANER COVER
Gv
w\\T
14
,PAPER
ELEMENT
FOAM ELEMENT
Carrier Extension
Pipe Lock Bolts
Check the carrier extension pipe lock bolts and make sure they are not loose.
If they are loose, tighten them securely by hand.
piziq
If the lock bolts are loose, the carrier side plates may come
off while a load is being transported, resulting in loss of the load.
LOCK BOLT
I
LOCK BOLT
15
5. STARTING THE ENGINE
Never run the engine in an enclosed or confined area. Exhaust contains
poisonous carbon monoxide gas; exposure can cause loss of consciousness and may lead to death.
1. Check that the gear shift lever is in the NEUTRAL position. Allow the drive
clutch levers to remain in the STOP position.
STOP
GEAR SHIFT LEVER
NEUTRAL
2. Turn the fuel valve to the ON position.
Be sure the drain knob is tightened.
FUEL VALVE
16
3. When the engine is cold, move the throttle lever to the FAST position and
move the choke rod to the CLOSE position.
CHOKE ROD
I
FAS
THROlTLE
LEVER
NOTE: If restarting a warm engine, the choke will not be needed. Restart a
warm engine with the throttle lever in the SLOW position and choke rod in the
OPEN position.
4. Turn the engine switch to the ON position.
ENGINE SWliCH
17
5. Pull the starter grip lightly until you feel resistance, then pull briskly.
ER GRIP
Do not allow the starter grip to snap back against the engine.
Return it gently to prevent damage to the starter.
Do not pull the starter grip while the engine is running, as that may
damage the starter.
Let the engine warm up for several minutes. If the choke rod has been
pulled to the CLOSE position, gradually move the choke rod to the OPEN
position and move the throttle lever to the SLOW position as the engine
warms up.
THROlTLE
SLOW
18
\
/
LEVER
CHoKERoY
I
6. OPERATION
1. Start the engine according to the procedures described on page 16.
Before operating this equipment
Safety information on page 4.
you should read and understand
the
2. Move the throttle lever to the FAST position for normal operation.
FAST
THROlTLE
LEVE
3. Move the gear shift lever to the desired position.
N: NEUTRAL
1: LOW SPEED
2: HIGH SPEED
R: REVERSE
N
liall
2
1
R
l
l
To avoid loss of control, descend steep slopes in low (1) gear, using
SLOW throttle position.
Do not shift gears while the power carrier is moving.
1 NOTICE
1
Al ways
shift gears with the engine running
clutch levers released.
and the drive
19
4. Squeeze the drive clutch levers down against the handlebars smoothly and
quickly. The power carrier will now start to move.
I“,
DRIVE CLUTCH LEVERS
RUN
If the engine stalls on a slope, release the drive clutch levers immediately
stop the power carrier and avoid loss of control.
to
5. Use the steering clutch levers to steer the power carrier. Pull up the right
lever to steer right. Pull up the left lever to steer left.
STEERING CLUTCH LEVERS
The turning action is abrupt. Be sure that loads are properly secured. Exercise
special care when steering on a slope.
High Altitude Operation
At high altitude,
the standard
air-fuel
mixture
will be too rich.
Performance will decrease, and fuel consumption will increase. A very rich
mixture will also foul the spark plug and cause hard starting.
High altitude performance can be improved by specific modifications
to the carburetor. If you always operate your power carrier at altitudes above
6,000 feet (1,800 meters),
have your servicing
dealer
perform
this carburetor modification.
Even with carburetor modification, engine horsepower will decrease about
3.5 % for each 1,000 foot (300 meter) increase in altitude. The effect of altitude
on horsepower will be greater than this if no carburetor modification is made.
When the carburetor has been modified for high altitude operation,
the air-fuel mixture will be too lean for low altitude use. Operation at
altitudes below 6,000 feet (1,800 meters) with a modified carburetor may
cause the engine to overheat and result in serious engine damage. For
use at low altitudes, have your servicing dealer return the carburetor to
original factory specifications.
21
7. STOPPING THE ENGINE
In an emergency:
1. To stop the engine in an emergency,
position.
turn the engine switch to the OFF
In normal use:
1. Release the drive clutch levers to disengage the drive and apply the brake.
DRIVE CLUTCH LEVERS
2. Move the gear shift lever to the NEUTRAL
position.
NEUTRAL
22
3. Move the throttle lever to the SLOW position.
THROTTOLE LEVER
4. Turn the engine switch to either OFF position.
OFF
ENGINE SWITCH
23
5. Turn the fuel valve to the OFF position.
24
8. CARRYING LOADS
Load Carrying Safety
To avoid accidents or overturning:
l
l
l
l
Observe the load limits described on page 29.
Do not stack the load so that the power carrier becomes top-heavy and
unstable.
Carry only lightweight
loads when the carrier side rails are extended.
Do not allow the load to protrude from the power carrier or block
visibility.
l
Secure the load to the tie-down hooks with strong ropes or straps.
l
Before operating the power carrier, check that the carrier bed is locked.
l
l
l
l
When operating the power carrier on ground that is soft or uneven,
reduce speed and exercise extra care.
Use low (1) gear and SLOW throttle position when descending
slopes. Never descend slopes in reverse gear.
steep
Exercise extra care when starting, stopping, or changing the direction
of the power carrier while operating it on slopes.
Do not carry loads on any slopes greater than 15”.
25
Tie-Down Hooks
When loading objects onto the carrier, be sure to a,dhere to the regulated
loading weight, proper loading methods and tilt angle. Failure to heed
these regulations will not only exert an adverse effect on the engine and
frame but will also create a hazard that the load may collapse or topple
over.
Secure the load in the carrier bed with strong ropes or straps attached to the
tie-down hooks.
Do not attach ropes or straps to locations other than the tie-down hooks.
1 NOTICE 1
When tying down a load with the carrier extended, make sure the width
of the carrier conforms to the width of the load. Caution is especially
required when a rope is tied to the rear plate of the carrier, since
deformation of the rear plate may occur.
26
Carrier Side Plate and Carrier Front Plate
Side plates
Loosen the 4 lock bolts on the left and right sides, and pull out the carrier side
plates in a horizontal direction so that the left and right sides are even (within
7.5 in) and the load is centered. After pulling out the side plates, tighten the lock
bolts securely.
LOCK BOLT
Front plate
Loosen the 2 lock bolts and pull out the front plate to suit the length of the load.
After pulling out the front plate, tighten the lock bolts securely.
460 mm (18.1 i
Maximum extension:
Side plate: 190 (7.5 in) mm each sid
Front plate: 460 (18.1 in) mm
pz?zE-j
l
l
If the unit is used with the plates extended beyond the above
dimensions, the carrier plates may come off, resulting in loss of the
load.
Use of the unit with the side plates extended and the front plate pulled
out is limited to light loads transported over flat terrain.
27
Dumping Loads
Dump loads with the power carrier stopped
released.
and the drive clutch
levers
1. Pull the carrier bed release lever, and tilt the carrier bed by lifting the
handlebar.
2. After dumping the load, push down firmly on the handlebar
carrier bed in the normal position.
I
to lock the
HkNDLEBAR
CARRIER BED RELEASE LEVER
m
Before operating the power carrier, check that the carrier bed
is locked. If the carrier bed is not locked, it may tilt while going downhill
and accidentally dump the load, which may cause personal injury and
property or equipment damage.
28
Load Carrying Capacity
To avoid personal injury and property or equipment damage due to
overturning, do not carry loads on any slopes greater than 15”. Observe
the following safe loading and operating limits:
l
l
For operation on lever ground Maximum load:
400 kg (881 Ibs)
Maximum load height:
900 mm (35.4 in)
For operation on slopes Maximum load:
250 kg (551 Ibs)
Maximum load height:
600 mm (23.6 in) upward
300 mm (11.8 in) downward
Maximum slope:
15” upward/l 5” downward
Slope
with
gradient
of under
15”
6
R
400 kg
(881 Ibs)
I
-
Slope
with
gradient
of under
15”
29
Carrier Bed Support Bar
For servicing the power carrier, lift the carrier bed and keep it tilted by setting
the carrier bed support bar.
CARRIER BED SUPPORT
BAR
Before servicing the power carrier, make sure that the carrier bed is
securely supported. If the carrier bed is not securely supported, it may
fall and cause personal injury or equipment damage.
30
9. MAINTENANCE
The Importance of Maintenance
Good maintenance is essential for safe, economical, and trouble-free operation. It will also help reduce air pollution.
To help you properly care for your power carrier, the following pages include
a maintenance schedule, routine inspection procedures, and simple maintenance procedures using basic hand tools. Other service tasks that are more
difficult, or require special tools, are best handled by professionals and are
normally performed by a Honda technician or other qualified mechanic.
The maintenance schedule applies to normal operating conditions. If you
operate your power carrier under unusual conditions, consult your servicing
dealer for recommendations applicable to your individual needs and use.
Improper
maintenance,
or failure to correct a problem before
I operation, can cause a malfunction in which you can be seriously hurt
or killed.
Always follow the inspection and maintenance
schedules in this owner’s manual.
recommendations
and
31
Maintenance
Safety
Some of the most important safety precautions follow. However, we cannot
warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task.
2
m
Failureto properly follow maintenance instructions
cause you to be seriously hurt or killed.
Always follow the procedures
and precautions
and precautions can
s
in the owner’s manual.
Safety precautions
l
l
l
Make sure the engine is off before you begin any maintenance
This will eliminate several potential hazards:
or repairs.
-
Carbon monoxide poisoning from engine exhaust.
Be sure there is adequate ventilation whenever you operate the engine.
-
Burns from hot parts.
Let the engine and exhaust system cool before touching.
-
Injury from moving parts.
Do not run the engine unless instructed to do so.
Read the instructions
and skills requred.
before you begin, and make sure you have the tools
To reduce the possibility of fire or explosion, be careful when working around
gasoline. Use only a nonflammable solvent, not gasoline, to clean parts.
Keep cigarettes, sparks, and flames away from all fuel-related parts.
Remember that your servicing dealer knows
and is fully equipped to maintain and repair it.
your
power
To ensure the best quality and reliability,
use only
Honda parts or their equivalents for repair or replacement.
carrier
new,
.
best
genuine
’
b
Proper Maintenance
Replacement
i
Y
is the Owner’s Responsibility
parts
Honda recommends only the use of new, genuine Honda parts or their
equivalent. The use of other replacement parts which are not of equivalent
quality may damage the power carrier.
Maintenance
Follow the maintenance schedule on page 34. Remember that this schedule
is based on the assumption that your machine will be used for its designed
purpose. Sustained high-load or high-temperature operation, or use in unusually wet conditions, will require more frequent service.
33
Maintenance
NOTE:
34
Schedule
(1) Service more frequently when used in dusty areas.
(2) These items should be serviced by an authorized
Honda
dealer,unless the owner has the proper tools and is mechanically
proficient. See the Honda Shop Manual.
Tool Kit
The tools supplied with the carrier are necessary for performing some periodic
maintenance, simple adjustments and repairs. Always keep the tool kit with
the carrier.
L
TOOL BAG
I
1
SPARK PLUG WRENCH HANDLE
0
SPARK PLUG WRENCH
OIL FUNNEL
35
Engine Oil Change
Drain the oil while the engine is still warm to assure rapid and complete
draining.
1. Remove the engine oil fillercap and
loosen the oil drain bolt.
2. Set the oil funnel as shown, remove
the oil drain bolt and drain the oil
into a suitable container.
3. Once the oil has been drained,
tighten the oil drain bolt securely.
4. Fill the crankcase with the recommended oil (see page 13) and check
the level.
5. After refilling, tighten the cap securely.
Oil capacity:
ENGINE OIL
FILLER CAP
Y
0.60 JZ(0.63 US qt, 0.53
Imp qt)
OIL
FUNNEL
UPPER LIMIT
Wash you hands with soap and water after handling used oil.
NOTE:
Please dispose of used motor oil in a manner that is compatible with the
environment. We suggest you take it in a sealed container to your local
recycling center or service station for reclamation. Do not throw it in the trash,
pour it on the ground, or down the drain.
36
5
Spark Plug Service
Recommended
.
I
spark plug: BPR4ES (NGK)
W14EPR-U (DENSO)
To ensure proper engine operation, the spark plug must be properly gapped
and free of deposits. If the engine has been running, the muffler will be very
hot. Be careful not to touch the muffler.
1. Remove the spark plug cap.
2. Clean any dir-l from around the spark plug base.
3. Use the wrench supplied in the tool kit to remove the spark plug.
4. Inspect the spark plug. Discard it if the electrodes are worn or if the insulator
is cracked or chipped. If it is to be reused, clean the electrode and insulator
with a wire brush.
f
37
5. Measure the plug gap with a feeler gauge.
Correct as necessary by bending the side electrode.
The gap should be:
0.70 - 0.80 mm (0.028 - 0.031 in)
PLUG GAP:
0.7 - 0.8 mm
10.028 - 0.031 in)
SIDE ELECTRODE
6. Make sure that the spark plug washer is in good condition, and thread the
spark plug in by hand to’prevent cross-threading.
7. After the spark plug is seated, tighten with a spark plug wrench to compress
the washer.
NOTE:
If installing a new spark plug, tighten l/2 turn after the spark plug seats to
compress the washer. If reinstalling a used spark plug, tighten l/8 to l/4 turn
after the spark plug seats.
l
l
Use only the recommended spark plug or equivalent. Spark plug
which have an improper heat range may cause engine damage.
The spark plug must be securely tightened. An improperly tightened
spark plug can become very hot and may damage the engine.
38
Air Cleaner Service
A dirty air filter will restrict air flow to the carburetor, reducing engine
performance. If you operate the power carrier in very dusty areas, clean the
air filter more often than specified in the Maintenance Schedule.
1 NOTICE 1
Operating the engine without an air filter, or with a damaged air filter, will allow
dirt to enter the engine, causing rapid engine wear. This type of damage is not
covered by the Distributor’s Limited Warranty.
Removal
1. Unscrew the wing nuts and remove the air cleaner cover.
2. Remove both air filter elements.
3. Separate both air filter elements and carefully check them for holes or tears
and replace as necessary.
WING NUTS
AIR CLEANER COVER
‘APER ELEMENT
FOAM ELEMENT
39
Cleaning
1. Paper element: Tap the element lightly several times on a hard surface to
remove excess dirt, or blow compressed air [not exceeding 270 kPa (30
psi)] through the filter element from the inside out. Never try to brush the dirt
off; brushing will force dirt into the paper fibers. Replace the paper element
if it is excessively dirty or damaged.
C’
2. Foam element cleaning: Wash
the element in a solution of household detergent and warm water,
then rinse thoroughly, or wash in
nonflammable solvent.
SOLVENT
ENGINE OIL
I,
I,=P
62
bb
3. Allow the element to dry thoroughly. Soak the element in clean
engine oil and squeeze out the
“<,@ ;’
SQUEEZE
THOROUGHLY
c
‘-
@F
bb
excess oil.
Excess oil will restrict air flow through the foam filter element and may
transfer to the paper filter ele..
ment, soaking and clogging it.
Installation
1. Wipe dirt from the inside of the air
cleaner housing and cover. Be
careful to prevent dirt from entering the air duct that leads to the
carburetor.
WING NUTS
/I
+lR CLEANER COVER
PAPER ELEMENT
OAM ELEMENT
2. Install the foam element over the
paper element, and install the
assembled air filter.
3. Install the air cleaner cover, and
secure with the wing nuts.
40
AIR CLEANER
HOUSING
Adjusting the Track Tension
If the tracks are not properly tensioned, they may slip off the wheels or their
service life may be reduced.
Inspection
Check that the track deflection is between 8-12 mm (0.31-0.47 in) when a
force (about 10 kg, 22.1 lb) is applied to the middle of the tracks.
8- 12mm
(0.31 .. 0.47 in1
Track adjustment
1. Tip up the carrier.
Loosen the two lock nuts until there is space between the nuts and the
frame.
2. Tighten the inner lock nut by hand until clearance between the lock nut and
frame is 5-l 0 mm (0.20-0.39 in).
3. Hold the inner lock nut and tighten the other lock nut against it securely.
NOTE: Use the two 19 mm wrenches as illustrated.
TRACK TENSION SPRING
FRAME SURFACE
Adjusting
the Drive Clutch Cable
The clutch will slip and the power carrier may not move unless the drive clutch
cable is adjusted properly.
1. Measure and record the distance between the clutch arm and cable holder
with the drive clutch levers at their released position (STOP). Next,
measure the same distance again with the levers at their applied position
(DRIVE).
The distance in the applied position should be l-2 mm (0.04-0.08 in) more
than in the released position.
?
P
2. To adjust, loosen the lock nuts and while repeatedly applying and releasing
the drive clutch levers, adjust so the change in distance of the cable holder
to the clutch arm is l-2 mm (0.04-0.08 in).
3. After adjustment, tighten the lock nuts.
DRIVE CLUTCH
CABLE
CLUTCH !RM
Applied
Released
.
‘
I
=x+lto2mm
(0.04 - 0.08 in)
42
Adjusting
the Brake Cable
1. Check whether the brake spring collar is 14 -16 mm (0.55-0.63 in) from the
spring holder when the drive clutch levers are at their released (STOP)
position.
2. To adjust, loosen the lock nuts with the levers still at the stop position, and
adjust the cable to the specified value.
3. After adjustment, tighten the lock nuts.
DRIVE CLUTCH LEVERS
BRAKE SPRING
SPRING HOLDER
\
BRAKE CABLE
43
Checking
Brake Wear
Check the brake shoe wear indication only after the brake cable has been
properly adjusted.
Brake shoe wear is OK if you cannot see the “A” mark through the brake arm
hole, when the drive clutch lever is in its released position (STOP).
However, if you can see any part of the (“A”) mark, the brake has worn past
its service limit; contact your authorized Honda dealer.
BRAKE ARM
BRAKE ARM HOLE
44
s
,
Adjusting
the Steering Clutch Cable
Steering control will be impaired
adjusted properly.
r
*
unless both steering
clutch cables are
1. With the engine off, rock the power carrier forward and backward to find the
position at which each lever can be pulled closest to the handle grip.
2. With each steering clutch lever fully gripped, check whether the clearance
between the tip of the lever and the handle grip is 30-35 mm (1.18-l .38
in).
3. To adjust, loosen the lock nut with the lever gripped, and turn the adjusting
bolt to get the specified clearance.
4. After the adjustment, tighten the lock nut.
//
HANDLE GRIP
STEERING CLUTCH LEVER
ADJUSTING
BOLT
45
Adjusting
the Dumping Lock Cable
1. With the carrier locked, check whether the play at the end of the carrier bed
release lever is 15-20 mm (0.55-0.79 in).
2. To adjust, loosen the lock nut and turn the adjusting bolt to set the specified
distance.
3. After adjustment,
tighten the lock nut.
8
15 - 20 mm
USTING BOLT
CARRIER BED RELEASE LEVER
46
Checking the Transmission
4
Oil
Remove the check bolt and check that the oil is up to the lower edge of the
check bolt hole. If it is low, refill with engine oil of the classification recommended on page 13.
BOLT
Checking the Clutch Oil
Remove the check bolt and check that the oil is up to the lower edge of the
check bolt hole. If it is low, refill with engine oil of the classification recommended on page 13.
,
CHECK BOLT
47
Spark Arrester Service (Optional part)
Your engine is not factory-equipped with a spark arrester. In some areas, it is
illegal to operate an engine without a spark arrester. Check local laws and
regulations. A spark arrester is available from authorized Honda servicing
dealers.
The spark arrester must be serviced every 100 hours to keep it functioning
designed.
as
If the engine has been running, the muffler will be very hot. Allow the muffler
to cool before servicing the spark arrester.
1. Remove the two 6 mm nuts and remove the muffler protector, identification
plate, muffler and gasket.
2. Remove the spark arrester from the muffler.
(Optional part)
MUFFLER
6 rnh NUTS
MUFFLER
PROTECTOR
3. Use a brush to remove carbon
deposits from the spark arrester
screen. Be careful not to damage
the spark arrester screen.
4. Inspect the spark arrester for
breaks and holes. Replace it if
necessary.
5. Install the spark arrester and the
muffler in the reverse order of
disassembly.
48
Lubrication
Grease the points noted below, at least once a year or after any time you have
washed the carrier. Recommended grease: SAE multipurpose grease.
CARRIER JOINT SECTION
,
DRIVE CLUTC
GEAR SHIFT LEVERJOINT
SECTION
CARRIER BED RELEASE LOCK SECTION
49
Temporary Installation
of a Disengaged Track
In the unlikely event that a track slips off the sprockets during operation,
proceed with the following:
.
1. Stop the engine (refer to page 22).
2. Remove any load in the carrier, by hand. Do not empty it by dumping the
carrier.
3. Move the power carrier to a flat surface and support on wood blocks in two
locations (so the wheels are off the ground). Dump the carrier.
[I
A carrier with a disengaged track will fall over if the carrier is
dumped, unless first secured with wood blocks.
4. Loosen the track tension lock nuts and tighten up the inner nut as far as it
will go. (This is done in order to facilitate the mounting of the track.)
5. Remove the sprocket bolts.
WRENCH 14 x 10
FRAME
LOCK NUTS
WRENCH 19
SPROCKET
BOLTS
WOODEN
50
BLOCKS
4
6. Remove the sprocket.
7. Place the track over the driven wheel, and engage the sprocket with the
track teeth.
8. Push the sprocket and track toward the rear, then slide the sprocket onto
the sprocket shaft.
9. Install and tighten the sprocket bolts securely.
DRIVEN WHEEL
SPROCKET BOLT
TRACK
\
DRIVEN WHEEL
SPROCKET
10. Remove the wooden blocks and make sure the power carrier is level.
Then adjust track tension.
1 NOTICE 1
l
l
l
Special care should be exercised when mounting the tracks.
Do not tip the carrier onto its side; oil and gasoline may spill out. Tip
it only enough to ease track installation.
After following the above temporary procedure, have the power
carrier inspected by your authorized Honda dealer as soon as possible.
51
10. TRANSPORTING/STORAGE
If the engine has been running, allow it to cool for at least 15 minutes before
loading the power carrier on the transport vehicle or placing it in storage. A hot
engine and exhaust system can burn you and can ignite some materials.
Turn the fuel valve to the OFF position, and transport or store the power carrier
in a level position. This will prevent carburetor flooding and reduce the
possibility of fuel leakage.
Before storing the unit for an extended period;
1. Be sure the storage area is free of excessive
humidity and dust.
2. Drain the fuel.
Gasoline is highly flammable and explosive.
You can be burned or seriously
l
l
l
injured when handling fuel.
Stop the engine and keep heat, sparks, and flames away.
Handle fuel only outdoors.
Wipe up spills immediately.
.
a. Turn the fuel valve ON.
b. Loosen the carburetor drain knob, and drain the gosoline into a suitable
container. After draining, retighten the drain knob and turn the fuel valve
OFF.
FUEL
52
3. Change the engine oil (see page 36 for details).
4. Clean the air cleaner (see page 40 for details).
5. Clean the power carrier and inspect all parts to make sure they are securely
tightened. Lubricate the points noted on page 49.
NOTE: If the carrier will be stored for more than three months, remove the
spark plug, pour a tablespoon (5-10~~) of clean engine oil into the cylinder.
Pull the starter rope slowly two or three times to distribute the oil. Reinstall the
spark plug.
6. Pull the starter grip until resistance is felt. This closes the valves and
protects the engine from internal corrosion.
R GRIP
.
7. With the engine and exhaust system cool, cover the power carrier to keep
out dust. A hot engine and exhaust system can ignite or melt some
materials. Do not use sheet plastic as a dust cover. A nonporous cover will
trap moisture around the power carrier, promoting rust and corrosion.
53
11. TROUBLESHOOTING
To assure maximum service life from your carrier, don’t disassemble it
unnecessarily. If the following basic troubleshooting does not get you and your
carrier back to work, it is time .to consult your authorized Honda dealer.
Check the following points if the engine does not start.
l
Is there sufficient fuel?
l
Is there sufficient engine oil?
l
Is there a spark at the spark plug?
a. Remove the spark plug cap. Clean any dirt from around the spark pulg
base, then remove the spark plug.
b. Install the spark plug in the plug cap.
c. Turn the engine switch on.
d. Ground the side electrode at any engine ground and crank the engine to
see if sparks jump across the gap.
Gasoline is highly flammable and explosive.
If ignited, gasoline can burn you severely.
l
l
Be sure there is no spilled fuel near the engine.
Place the spark plug away from the spark plug hole.
e. If there are no sparks, replace the plug. If sparks occur, install the spark
plug, and try to start the engine according to the instructions.
Check the following
properly:
if the engine
runs but the carrier does not operate
l
Is the drive clutch cable adjusted (page 42)?
l
Are the steering clutch cables adjusted (page 45)?
l
Is the brake cable properly adjusted (page 43)?
l
Are the tracks adjusted to proper tension (page 41)?
54
12. SPECIFICATIONS
Type
I I
Honda power carrier HP400 K3 (BA)
I ’
Power product
discription code
.
Engine
118 cm3 (7.2 cu in)
Displacement
Bore and stroke
60 x 42 mm (2.4 x 1.7 in)
25” BTDC
Ignition timing
Ignition system
Transistorized
Engine oil capacity
0.6 P (0.63 US gal, 0.53 Imp gal)
Fuel tank capacity
magneto ignition
1.6 P (1.68 US gal, 1.41 Imp gal)
BPR4ES (NGK) W14ERR-U
Spark plug
I
GXVlPO
4-stroke, overhead valve, 1 cylinder
Engine type
b
I
NAA
(DENSO)
FRAME
,
Overall length
1900 mm (74.8 in)
Overall width
635 mm (24.9 in)
Overall height
1055 mm (41.5 in)
Dry weight
178 kg (392 Ibs)
Unloaded operating weight
Traveling speed
Maximum
load
capacity
400 kg
(881 lb)
Sloping
ground
250 kg
(551 lb)
oil capacity
Track width x lenath
.
1.4 km/h (0.9 mile/h) in 1 st gear, 3.5 km/h (2.2 mile/h)
in 2nd gear, 1.3 km/h (0.8 mile/h) in reverse
Level
ground
Clutch oil caoacitv
Transmission
181 kg (399 Ibs)
2 forward aears. 1 reverse aear
No. of aears
NOTE: Specifications
0.8 P (0.84 US at, 0.71 Imp at)
2.0 P (0.21 US qt, 1.76 Imp qt)
180 mm x 2220 mm (7.1 x 87.4 in)
I
are subject to change without notice.
55
13. WARRANTY SERVICE INFORiblATlON
Honda power equipment dealership personnel are trained professionals.
They should be able to answer any question you may have. If you
encounter a problem that your dealer does not solve to your satisfaction,
please discuss it with the dealership’s management. The Service Manager
or General Manager can help. Almost all problems are solved in this way.
If you are dissatisfied
with the decision
made by the dealership’s
management, contact the Honda Power Equipment Customer Relations
Office. You can write to:
American Honda Motor Co., Inc
Power Equipment Division
Customer Relations Office
4475 River Green Parkway
Duluth, Georgia 30136-9420
Or telephone:
(770)497-6400
When you write or call, please give us this information:
l
Model and serial number
l
Name of dealer who sold the power carrier to you
l
Name and address of dealer who services your power carrier
l
Date of purchase
l
Your name, address, and telephone
l
A detailed description
56
of the problem
number
14. INDEX
;;
CARRYING LOADS ....... ..............................................................................................................................................................
Carrier Bed Support Bar
27
Carrier Side Plate and Carrier Front Plate .............................................................................
;i
Dumping Loads ......................................................................................................................................................................
Load Carrying Capacity
Ez
Load Carrying Safety .............................................................................................................
Tie-Down Hooks ....................................................................................................................
..................................................................................................
5
COMPONENT IDENTIFICATION
.
CONTROLS ..... ..............
Carrier Bed Release .............................................................................................................................................................
Lever
0
Drive Clutch Levers ............... ..................................................................................................
6
Engine Switch ..........................................................................................................................
6
Fuel Valve ................................................................................................................................
a
Gear Shift Lever .................... ..................................................................................................
7
Starter Grip ..............................................................................................................................
g
Steering Clutch Levers ............................................................................................................
7
Throttle Lever ..........................................................................................................................
57
INDEX ..........................................................................................................................................
MAINTENANCE ...........................................................................................................................
31
43
Adjusting the Brake Cable .....................................................................................................
.42
Adjusting the Drive Clutch Cable ..........................................................................................
.46
Adjusting the Dumping Lock Cable ...................... . ...............................................................
45
Adjusting the Steering Clutch Cable ......................................................................................
Adjusting the Track Tension .................................................................................................
Air Cleaner Service ...............................................................................................................
Checking Brake Wear.. ..........................................................................................................
Checking the Clutch Oil .........................................................................................................
Checking the Transmission Oil ..............................................................................................
Engine Oil Change ................................................................................................................
.
.41
.3g
44
47
47
36
“,z
Lubrication ...
...........................................................................................................................................................................
Maintenance Safety
34
Maintenance Schedule ..........................................................................................................
.33
Proper Maintenance is the Owner’s Responsibility ..............................................................
Spark Arrester Service (Optional part) .................................................................................
.46
37
Spark Plug Service ................................................................................................................
.5O
Temporary Installation of a Disengaged Track .....................................................................
.3t
The Importance of Maintenance ...........................................................................................
35
Tool Kit ..................................................................................................................................
OPERATION ................................................................................................................................
19
21
High Altitude Operation .........................................................................................................
16
PRE-OPERATION CHECK ..........................................................................................................
Air Cleaner .............................................................................................................................
14 .
Carrier Extension Pipe Lock Bolls .........................................................................................
15
Engine Oil ..............................................................................................................................
13
IO
Fuel.. ......................................................................................................................................
3
SAFETY .........................................................................................................................................
4
SAFETY INFORMATION
........................................................................................................
3
SAFETY LABEL LOCATIONS .................................................................................................
55
.......................................................................................................................
SPECIFICATIONS
16
STARTING THE ENGINE ............................................................................................................
22
STOPPING THE ENGINE ............................................................................................................
.52
TRANSPORTING/STORAGE
.....................................................................................................
54
.................................................................................................................
TROUBLESHOOTING
56
WARRANTY SERVICE INFORMATION ......................................................................................
57
MEMO
HONDA
31742702
00X31
-742-7020
6B
Printed on
Recycled Paper
@g
K3
01009707
PRINTED IN U.S.A.

advertisement

Key Features

  • Track Drive System
  • Carrier Bed
  • Tie-Down Hooks
  • Engine Switch
  • Fuel Valve
  • Throttle Lever
  • Gear Shift Lever
  • Drive Clutch Levers
  • Steering Clutch Levers
  • Carrier Bed Release Lever

Frequently Answers and Questions

How do I start the Honda HP400BA?
Refer to the Starting the Engine section on page 16 in the viewed document. Make sure the gear shift lever is in Neutral, fuel valve is ON, choke rod is in the CLOSE position, engine switch is ON and then pull the starter grip briskly.
What is the maximum load capacity of the HP400BA?
The maximum load capacity is 400 kg (881 lbs) for operation on level ground, and 250 kg (551 lbs) for operation on slopes. Refer to page 29 in the viewed document.
How do I change the engine oil?
Refer to the Engine Oil Change section on page 37 in the viewed document. You will need 4-stroke motor oil that meets or exceeds the requirements for API service classification SF or SG.

Related manuals

Download PDF

advertisement