Vonets | VAP11G | VAP11G WiFi Bridge User Manual

www.vonets.com
VAP11G User Manual
User Manual
VAP11G WiFi Bridge
IEEE 802.11b/g
-1-
www.vonets.com
VAP11G User Manual
1. Introduction
Thanks for choosing Vonets VAP11G WiFi Bridge.
With this portable device, VoIP Phone Adapters, IP Phones and other
IT products with Ethernet RJ45 port can access wireless network easily.
shown as below.
-2-
Two kinds of application topology of VAP11G are
www.vonets.com
VAP11G User Manual
VAP11G provides users a combination of Ethernet network and power cable, VAP11G uses the original power supply of VoIP
phone adapter or some other IT products’ power supply which has DC 2.0 power jack (5-15V, 1.5W). One power supply can
power VAP11G, as well as the VoIP phone adapter.
Please use power supply with the polarity as shown below. Power supply with different polarity will damage VAP11G and the
devices which the power supply belongs to. Vonets will NOT be responsible for the loss caused by using the incorrect power
supply. (Both Power Jack and Power Port are compliable with this polarity)
Alternatively, Vonets can also provide power supply for VAP11G(Optional).
Correct Power Adapter Polarity
-3-
www.vonets.com
VAP11G User Manual
2. Setup
Physical Connection for Setup
-4-
www.vonets.com
VAP11G User Manual
Running the Setup Wizard
1. Click Start Configuration on the first screen.
2.
Reading the agreement, click Next if you agree,
click Cancel to exit the wizard.
-5-
www.vonets.com
VAP11G User Manual
3.
After reading the Product Overview on screen 2, click Next.
4.
Double check the physical connection according to the instruction on screen 3, 4 and 5.
Please always click Next to continue.
-6-
www.vonets.com
5.
VAP11G User Manual
Users can see a list of all VAP11G WiFi bridge can be detected
by the wizard, select the one you are installing, click Next to
continue. You can also click Refresh List button to check again.
6. Screen 7 will show a list of available wireless network can be
detected and their specific information, including SSID,
MAC address, Signal Strength, Channel and Security type, select
one you are planning to enter.
To enter a SSID of the network you want, click SSID button and
complete the SSID field.
-7-
www.vonets.com
7.
VAP11G User Manual
Configure the wireless security settings. Select the method your
network is using, WPA, WPA2, WEP (128-Bit), or WEP (64-Bit).
Then proceed to the appropriate instructions. If you are not using
wireless security, select Disabled, and proceed to screen 10.
WPA
WPA automatically uses TKIP with dynamic encryption keys. Enter a passphrase on this screen.
Encryption - TKIP is automatically selected as the encryption method.
Passphrase - Enter a Passphrase, also called a pre-shared key, of 8-63 characters in the Passphrase field.
The longer and more complex your Passphrase is, the more secure your network will be.
Click Next to proceed, or click Back to return to the previous screen.
WPA2
WPA2 automatically uses AES with dynamic encryption keys (AES is a stronger encryption method than TKIP).
Enter a passphrase on this screen.
Encryption - AES is automatically selected as the encryption method.
Passphrase - Enter a Passphrase, also called a pre-shared key, of 8-63 characters in the Passphrase field.
The longer and more complex your Passphrase is, the more secure your network will be.
Click Next to proceed, or click Back to return to the previous screen.
-8-
www.vonets.com
VAP11G User Manual
WEP (128-Bit) or WEP (64-Bit)
Enter a passphrase in the Passphrase field and click Next. If you want to manually enter a WEP key,
leave the Passphrase field blank and click Next.
Passphrase - Enter a passphrase in the Passphrase field, so a WEP key is automatically generated.
The passphrase is case-sensitive and should not be longer than 16 alphanumeric characters. It must
match the passphrase of your other wireless network devices.
A new screen will appear. If you entered a Passphrase, the WEP key(s) will be displayed. If you did not
enter a Passphrase, enter the WEP key(s) on this screen. Then select the key you will use from the
Key Index dropdown menu.
Key 1-4 - One to four fields will be displayed, depending on the level of encryption you have selected. The
WEP key you enter must match the WEP key of your wireless network. For 64-bit WEP encryption, enter
exactly 10 hexadecimal characters. For 128-bit WEP encryption, enter exactly 26 hexadecimal characters.
Valid hexadecimal characters are “0” to “9” and “A” to “F”.
Key Index - The default transmit key number is 1. If your network’s access point or wireless router uses
transmit key number 2, 3, or 4, select the appropriate number from the Key Index drop-down menu.
Click Next to proceed, or click Back to return to the previous screen.
-9-
www.vonets.com
VAP11G User Manual
8.
The New settings will be shown.
Click Next to save your new settings.
9.
VAP11G will attempt to connect the wireless network with the new settings.
Make sure the Bridge’s Wireless LED is solidly lit or flashing. This indicates that the Bridge has
connected to the wireless network. If the attempt succeeds, proceed to screen 12.
If the attempt fails, you have two options offered by a pop-up screen. Click the Yes button to save
the new settings and proceed, or click the No button to return to the Choose a Wireless Network
screen and reconfigure the settings
To make sure VAP11G is working, cut off all other internet connection to the PC (only reserve the connection
between the PC and VAP11G). If you setup VAP11G successfully, the PC can view internet now.
- 10 -
www.vonets.com
VAP11G User Manual
3. Typical Application for VoIP Phone Adapter
1.
Disconnect the Ethernet cable of VAP11G from the PC.
Click Next to proceed, or click Back to return to the previous screen.
2.
Disconnect the power adapter from the electrical outlet.
Click Next to proceed, or click Back to return to the previous screen.
- 11 -
www.vonets.com
3.
VAP11G User Manual
Disconnect the Ethernet cable form VoIP phone adapter.
You will use the combination Ethernet network and power cable attached to the Bridge.
Connect the Ethernet network cable of the Bridge to the phone adapter or IP phone.
Click Next to proceed, or click Back to return to the previous screen.
5.
Connect the power cable of the Bridge to the Power port of the
VoIP phone adapter. Then connect the power adapter to an
electrical outlet.
Make sure the Bridge’s Ethernet and Wireless LEDs are solidly lit or flashing.
Click Next to proceed, or click Back to return to the previous screen.
- 12 -
www.vonets.com
5.
VAP11G User Manual
Double check ethernet and power connection is followed by the Setup Wizard Instructions.
Click Next to proceed to the end.
- 13 -
Download PDF

advertising