Schluter KKB81152PVCEOB Kerdi-Shower 32 in. x 60 in. Off-Center Shower Kit in PVC with Oil-Rubbed Bronze Stainless Steel Drain Grate Installation guide

Below you will find brief information for Shower System KERDI-DRAIN, Shower System KERDI-BOARD, Shower System KERDI-SHOWER-ST, Shower System KERDI-SHOWER-SC, Shower System KERDI-SHOWER-SB, Shower System KERDI-SHOWER-L. These products are designed to create a durable, water-tight shower system that is easy to install and maintain. The KERDI-DRAIN is a drain that is integrated into the shower system, making it easy and secure to install. The KERDI-BOARD is a lightweight, easy to cut and install XPS foam panel that combines substrate installation and waterproofing. The KERDI-SHOWER-ST is a prefabricated foam shower tray that is easy to install and reduces installation time. The KERDI-SHOWER-SC is a preformed, lightweight and easy to install curb that can be cut to length. The KERDI-SHOWER-SB is a preformed, lightweight, easy to install bench that is available in triangular and rectangular shapes in various sizes. The KERDI-SHOWER-L is a prefabricated foam shower tray that is easy to install and reduces installation time.

PDF Download

Document

Schluter

-Shower System Installation Handbook 2015

Bonded Waterproofing System for Tiled Showers,

Steam Showers, Steam Rooms, and Bathtub Surrounds

Schluter ® -Shower System

Bonded Waterproofing System for Tiled Showers,

Steam Showers, Steam Rooms, and Bathtub Surrounds

Ceramic and stone tiles are durable, easy to maintain, and hygienic, representing the ideal surface coverings, particularly in wet areas such as showers and bathtub surrounds. These coverings are not inherently waterproof, however, and must be installed in conjunction with a waterproofing system that effectively manages moisture to protect moisture-sensitive building materials and control mold growth.

Pre-slope

Weep holes

Pan liner

Mortar bed

The Traditional Tiled Shower System

The traditional method for installing tiled showers is time and labor intensive and creates a “water in/water out” system. First, a mortar bed is sloped to the weep holes in the drain. The waterproofing membrane, called a pan liner, is placed over this “pre-slope” and clamped into the drain. Pan liners do not allow for the direct application of ceramic or stone tile. Thus, another mortar bed must be installed to provide load distribution and a bonding surface for the floor tile. Finally, a moisture barrier typically must be included behind the solid backing on the walls

(e.g., mortar, cement backerboard, etc.) and lapped over the pan liner to protect the wall cavities from moisture penetration and divert that moisture into the pan.

Contrary to popular belief, the tile covering itself is not waterproof. Moisture will infiltrate the mortar bed and solid backing on the walls. This moisture must percolate through the mortar bed to the sloped pan liner and exit through the weep holes in the drain. With regular use of the shower the mortar bed can remain saturated, particularly if pre-slope installation is ignored or the weep holes become clogged, thus increasing the potential for efflorescence and mold growth within the system.

Schluter ® -KERDI-DRAIN

Sloped mortar bed or

Schluter ® -KERDI-SHOWER-ST prefabricated foam tray

Schluter ® -KERDI waterproofing membrane

Schluter

-Shower System

The Schluter ® -Shower System is an integrated family of products that creates a

“sealed” system. First, the Schluter ® -KERDI-DRAIN is installed in conjunction with either a sloped mortar bed or the Schluter ® -KERDI-SHOWER-ST prefabricated foam tray. The KERDI-DRAIN provides a simple and secure connection to the Schluter ® -KERDI waterproofing membrane at the top of the assembly via the unique integrated bonding flange. Unlike shower pan liners in traditional assemblies, KERDI is a bonded waterproofing membrane that allows for the direct application of tile with thin-set mortar. KERDI is bonded to the mortar bed or tray and the surface of the KERDI-DRAIN’s integrated bonding flange. In addition, KERDI is installed over the solid backing (e.g., gypsum board, cement backerboard, etc.) on walls, creating a fully waterproof and vaportight enclosure.

The resulting assembly provides superior moisture management as it does not permit moisture to penetrate into the mortar bed or solid backing, allowing the assembly to dry completely between uses. The integrated Schluter

-Shower

System eliminates leaks, reduces the potential for efflorescence and mold growth in the system, and dramatically reduces total installation time to ensure success and make shower installation easier than ever.

Schluter

-Systems’ written installation instructions shall have precedence over referenced industry

standard guidelines and installation procedures insofar as referenced information may contain overlapping or conflicting requirements. Type, thickness, and format of the tile or stone surface covering must be suitable for the intended application.

SHOWER SELECTION GUIDE

SHOWER ASSEMBLY

4

6

Schluter ® -KERDI waterproofing membrane

8

Schluter ® -KERDI-BOARD waterproof building panel

10 Barrier-free showers

STEAM SHOWER ASSEMBLY

STEAM ROOM ASSEMBLY

INSTALLATION

BATHTUB SURROUND

12

Schluter ® -KERDI waterproofing membrane

14

Schluter ® -KERDI-BOARD waterproof building panel

16

Schluter ® -KERDI-DS waterproofing membrane

18 Bathtub surround assembly

20 Walls and ceilings

21

Schluter ® -KERDI-BOARD-SN shower niche

22 Shower base with

Schluter ® -KERDI-DRAIN

26 Shower base with

Schluter ® -KERDI-LINE

31 Bathtub surround

33 Accessibility and style

34 Security and utility

BARRIER-FREE SHOWERS

THE WATERPROOF BATHROOM

PROFILES

THIN-SET FACTS

TESTING, LISTINGS,

& APPROVALS

MOLD

VAPOR

PRODUCT & ORDERING INFO

WARRANTY

35 Details make the difference

36 Discussion on thin-set mortar types to be used

with

Schluter ® -KERDI

37 Products and system evaluation

38 The importance of mold control

39 The importance of water vapor management

40

47

SHOWER SELECTION GUIDE

Beautiful, durable, functional

The Schluter ® -Shower System is versatile to fit the needs of the installer. The Shower Selection Guide describes the available options to help you determine which products will best fit your shower application.

KERDI

KERDI-DRAIN

KERDI-BOARD

Waterproofing options

Schluter ® -KERDI waterproofing membrane over solid backing

• Thickness: 8 mil (0.2 mm)

• Pliable, easy to install, and guarantees uniform thickness for reliable performance

• Suitable for use in showers, bathtub surrounds, and intermittent-use steam showers

Schluter ® -KERDI-DS waterproofing membrane over solid backing

• Thickness: 20 mil (0.5 mm)

• Provides improved vapor permeance as compared to KERDI

• Suitable for use in continuous-use steam rooms

Schluter ® -KERDI-BOARD waterproof building panel

• Lightweight, easy to cut and install XPS foam panel

• Combines substrate installation and waterproofing

• Suitable for use in showers, bathtub surrounds, and intermittent-use steam showers

Drain options

• Integrated bonding flange ensures waterproof connection at top of assembly

• Can be installed with prefabricated foam shower trays or mortar bases

• Simple connection to standard drain outlets for new construction or renovation

• Grate assemblies accommodate a wide range of tile thicknesses

Schluter ® -KERDI-DRAIN

• Fully adjustable square grate assemblies minimize and simplify tile cuts

• Available with 2" or 3" (50 mm or 75 mm) outlets

• Adaptor kits allow for conversion of existing clamping ring drain to KERDI-DRAIN

Schluter ® -KERDI-LINE

• Accommodates single-plane slope and large-format tile installation

• Can be installed adjacent to walls or at intermediate locations

KERDI-LINE

KERDI-SHOWER-ST Mortar Bed

Shower base options

Schluter prefabricated shower trays

• Lightweight, easy to install

• Reduces installation time

• Available in a variety of formats to suit your installation needs

• Can be cut to size or extended using dry pack mortar

Portland cement mortar bed

• Base can be built for custom shower, fits any shape

• Especially suited for off-set drain placement

4 SHOWER SELECTION GUIDE

KERDI-SHOWER-SC

KERDI-BOARD Built-up Curb

KERDI-SHOWER-SB

KERDI-BOARD

Curb options

Schluter ® -KERDI-SHOWER-SC curb

• Preformed, lightweight and easy to install

• Can be cut to length

• Can be used with Schluter prefabricated shower trays or mortar base applications

Schluter ® -KERDI-BOARD curb

• Customizable to fit any application

• Build as desired (e.g., length, width, height)

• Can be installed over various materials (e.g., masonry, wood)

Built-up curb

• Customizable to fit any application

• Can be built as desired (e.g., length, width, height)

Bench options

Schluter ® -KERDI-SHOWER-SB bench

• Preformed, lightweight, easy to install

• Available in triangular and rectangular shapes in various sizes

Schluter ® -KERDI-BOARD bench

• Customizable to fit any application, can be built as desired

• Combines substrate installation and waterproofing

Built-up bench

• Customizable to fit any application

• Can be built as desired (e.g., length, width, height)

Shower niche

Schluter ® -KERDI-BOARD-SN shower niche

• Prefabricated shower niche made of KERDI-BOARD

• Preformed, lightweight, easy to install

• Various sizes available

SHOWER SELECTION GUIDE 5

SHOWER ASSEMBLY

Showers – Ceramic or stone tile

Schluter

-KERDI waterproofing membrane

K-SH-K-15

9 a

8 a

9 b

8 b

1 Ceramic or stone tile 8 Drain:

Unmodified thin-set mortar

Schluter ® -KERDI waterproofing membrane a.

Schluter ® -KERDI-DRAIN b.

Schluter ® -KERDI-LINE

Schluter ® -KERDI-BAND waterproofing strips

Schluter ® -KERDI-KERECK-F waterproofing corners

Schluter ® -KERDI-SEAL-PS/-MV seals or Schluter ® -KERDI-FIX sealant and bonding compound

Solid backing

9 Base: a.

Schluter ® -KERDI-SHOWER-ST b.

Schluter ® -KERDI-SHOWER-L/-LS

Alternative (not shown):

• Mortar bed

10 Schluter curb

® -KERDI-SHOWER-SC

Alternatives (not shown):

• Schluter ® -KERDI-BOARD waterproof building panel

• Built-up curb

6 SHOWER ASSEMBLY — Schluter

-KERDI waterproofing membrane

11 Wood or concrete subfloor

12 Schluter ® -DILEX profile (optional)

Bench (not shown):

• Schluter ® -KERDI-SHOWER-SB bench (optional)

• Schluter ® -KERDI-BOARD bench (optional)

Niche (not shown):

• Schluter ® -KERDI-BOARD-SN niche (optional)

Showers – Ceramic or stone tile

Schluter

-KERDI waterproofing membrane

K-SH-K-15

Areas of Application

Interior showers.

Over wood or concrete subfloors.

Areas requiring disabled access/barrier-free applications; see detail

K-SHBF on page 10.

Substrate Preparation

Verify that subfloor panels and solid backing are properly fastened to framing members.

Any leveling of the subfloor must be done prior to installing

KERDI-SHOWER-ST/-L/-LS/-SC/-SB/-SR.

Limitations

Certain glass tiles may not be compatible with bonded waterproof membranes and/or may require special setting materials. Consult glass tile manufacturer and Schluter ® -Systems for more information.

Certain moisture sensitive stones, e.g., green marble, or resin-backed tiles may not be appropriate for use in wet areas such as showers or may require special setting materials. Consult stone supplier and

Schluter ® -Systems for more information.

Do not use sawn lumber curbs on concrete subfloors subject to moisture migration.

Solid Backing Materials

Gypsum wallboard – ASTM C1396/C1396M

Cementitious backer unit – ANSI A118.9 or ASTM C1325

Fiber-cement underlayment – ASTM C1288

Fiber-reinforced water-resistant gypsum

backerboard/underlayment – ASTM C1278

Coated glass mat water-resistant gypsum backerboard – ASTM C1178

Portland cement mortar – ANSI A108.1B

Concrete

Masonry

Requirements

Plywood, OSB, or concrete subfloor must be clean, even, and load bearing.

Solid backing – gypsum wallboard, cementitious backer unit, fiber-cement underlayment, fiber-reinforced water-resistant gypsum backerboard/underlayment, coated glass mat water-resistant gypsum backerboard, Portland cement mortar bed, concrete, or masonry.

Base – KERDI-SHOWER-ST/-L/-LS or Portland cement mortar bed.

Curb – KERDI-SHOWER-SC, KERDI-BOARD, concrete, masonry block, or sawn lumber sheathed with solid backing (see above).

Bench – KERDI-SHOWER-SB, KERDI-BOARD, concrete, masonry block, or sawn lumber sheathed with solid backing (see above).

KERDI-DRAIN/-LINE shall be properly supported.

KERDI-DRAIN/-LINE shall be connected to the waste line; use ABS cement for ABS drains, PVC cement for PVC drains, a no-hub coupling for stainless steel drains with no-hub outlets, and thread sealing compound or tape for stainless steel drains with threaded outlets.

KERDI waterproofing membrane shall be installed up to the height of the showerhead at minimum.

Any protrusions through the KERDI membrane (e.g., showerhead, mixing valve, etc.) must be treated with KERDI-SEAL-PS/-MV seals, KERDI-FIX or suitable sealant.

When using the stainless steel KERDI-DRAIN bonding flange, use

KERDI-FIX to bond KERDI to the drain.

Setting and Grouting Materials

Unmodified thin-set mortar – ANSI A118.1

Grout – ANSI A118.3, A118.6, A118.7

Installation Specifications

Solid backing panels – follow manufacturer’s instructions

Portland cement mortar bed – ANSI A108.1B

Tile – ANSI A108.5

Grout – ANSI A108.6, A108.10

Other Considerations

When KERDI-SHOWER-ST/-L/-LS tray dimensions do not match the dimensions of the shower compartment, the tray may be cut or extended with dry pack mortar.

When KERDI and tile are installed on the ceiling, the solid backing and fasteners must be able to support the load of the tile and setting and grouting materials.

Schluter ® -Systems profiles may be used to finish and protect outside corners and eliminate the use of sealant at inside corners; see page 35.

SHOWER ASSEMBLY — Schluter

-KERDI waterproofing membrane 7

SHOWER ASSEMBLY

Showers – Ceramic or stone tile

Schluter

-KERDI-BOARD waterproof building panel

K-SH-KB-15

5 8

9 a

10 a

10 b

9 b

Ceramic or stone tile

Unmodified thin-set mortar

9 Drain: a.

Schluter ® -KERDI-DRAIN

12 Wood or concrete subfloor

13 Schluter ® -DILEX profile (optional)

Schluter ® -KERDI waterproofing membrane

Schluter ® -KERDI-BOARD waterproof building panel b.

Schluter ® -KERDI-LINE

10 Base: a.

Schluter ® -KERDI-SHOWER-ST

Bench (not shown):

• Schluter ® -KERDI-SHOWER-SB bench (optional)

• Schluter ® -KERDI-BOARD bench (optional)

5 Schluter washers

® -KERDI-BOARD-ZT b.

Schluter ® -KERDI-SHOWER-L/-LS

6 Schluter ® -KERDI-BAND waterproofing strips

Alternative (not shown):

• Mortar bed

Schluter ® -KERDI-KERECK-F waterproofing corners

Schluter seals or

® -KERDI-SEAL-PS/-MV

Schluter ® -KERDI-FIX sealant and bonding compound

11 Schluter ® -KERDI-SHOWER-SC curb

Alternatives (not shown):

• Schluter ® -KERDI-BOARD waterproofing panel

• Built-up curb

8 SHOWER ASSEMBLY — Schluter

-KERDI-BOARD waterproof building panel

Niche (not shown):

• Schluter ® -KERDI-BOARD-SN niche (optional)

Showers – Ceramic or stone tile

Schluter

-KERDI-BOARD waterproof building panel

K-SH-KB-15

Areas of Application

Interior showers.

Over wood or concrete subfloors.

Areas requiring disabled access/barrier-free applications; see detail

K-SHBF on page 10.

Substrate Preparation

Verify that subfloor panels are properly fastened to framing members.

Any leveling of the subfloor must be done prior to installing

KERDI-SHOWER-ST/-L/-LS/-SC/-SB/-SR.

Limitations

Certain glass tiles may not be compatible with bonded waterproof membranes and/or may require special setting materials. Consult glass tile manufacturer and Schluter ® -Systems for more information.

Certain moisture-sensitive stones, e.g., green marble, or resin-backed tiles, may not be appropriate for use in wet areas such as showers or may require special setting materials. Consult stone supplier and

Schluter ® -Systems for more information.

Do not use sawn lumber curbs on concrete subfloors subject to moisture migration.

Solid Backing Materials

Gypsum wallboard – ASTM C1396/C1396M

Cementitious backer unit – ANSI A118.9 or ASTM C1325

Fiber-cement underlayment – ASTM C1288

Fiber-reinforced water-resistant gypsum backerboard/underlayment –

ASTM C1278

Coated glass mat water-resistant gypsum backerboard – ASTM C1178

Portland cement mortar – ANSI A108.1B

Concrete

Masonry

Requirements

Plywood, OSB, or concrete subfloor must be clean, even, and load bearing.

Base – KERDI-SHOWER-ST/-L/-LS or Portland cement mortar bed.

Curb – KERDI-SHOWER-SC, KERDI-BOARD, concrete, masonry block, or sawn lumber sheathed with solid backing (see below).

Bench – KERDI-SHOWER-SB, KERDI-BOARD, concrete, masonry block, or sawn lumber sheathed with solid backing (see below).

Solid backing – gypsum wallboard, cementitious backer unit, fibercement underlayment, fiber-reinforced water-resistant gypsum backerboard/underlayment, coated glass mat water-resistant gypsum backerboard, Portland cement mortar bed, concrete, or masonry.

KERDI-DRAIN/-LINE shall be properly supported.

Minimum KERDI-BOARD thickness – 1/2" (12.5 mm) for studs spaced at

16" (40.6 cm) o.c. and 3/4" (19 mm) for studs spaced at 24" (61.0 cm) o.c.

KERDI-BOARD shall be fastened to wood or metal framing with screws and corresponding KERDI-BOARD-ZT washers. Screws must reach a depth of at least 3/4" (20 mm) in wood studs and 3/8" (10 mm) in metal studs. Maximum allowable on-center fastener spacing is 12" (30 cm) for walls and 6" (15 cm) for ceilings.

KERDI-BOARD shall be installed up to the height of the showerhead at minimum.

Any protrusions through the KERDI-BOARD (e.g., showerhead, mixing valve, etc.) must be treated with KERDI-SEAL-PS/-MV seals, KERDI-FIX or suitable sealant.

When using the stainless steel KERDI-DRAIN bonding flange, use

KERDI-FIX to bond KERDI to the drain.

Setting and Grouting Materials

Unmodified thin-set mortar – ANSI A118.1

Grout – ANSI A118.3, A118.6, A118.7

Installation Specifications

Portland cement mortar bed – ANSI A108.1B

Tile – ANSI A108.5

Grout – ANSI A108.6, A108.10

Other Considerations

When KERDI-SHOWER-ST/-L/-LS tray dimensions do not match the dimensions of the shower compartment, the tray may be cut or extended with dry pack mortar.

Shower grab bars must be anchored in the structure or solid blocking behind KERDI-BOARD.

When KERDI-BOARD and tile are installed on the ceiling, the fasteners must be able to support the load of the tile and setting and grouting materials.

Schluter ® -Systems profiles may be used to finish and protect outside corners and eliminate the use of sealant at inside corners; see page 35.

SHOWER ASSEMBLY — Schluter

-KERDI-BOARD waterproof building panel 9

SHOWER ASSEMBLY

Barrier-free Showers – Ceramic or stone tile

Schluter

-KERDI waterproofing membrane or

Schluter

-KERDI-BOARD waterproof building panel

K-SHBF-15

3 1

9 a

10 a

9 b

10 b

1 Ceramic or stone tile 9 Drain:

Unmodified thin-set mortar

Schluter ® -KERDI waterproofing membrane a.

Schluter ® -KERDI-DRAIN b.

Schluter ® -KERDI-LINE

4 Schluter ® -KERDI-BOARD waterproof building panel

10 Base: a.

Schluter ® -KERDI-SHOWER-ST

5 Schluter ® -KERDI-BOARD-ZT washers b.

Schluter ® -KERDI-SHOWER-L/-LS

6 Schluter ® -KERDI-BAND waterproofing strips

Alternative (not shown):

• Mortar bed

7 Schluter ® -KERDI-KERECK-F waterproofing corners

8 Schluter ® -KERDI-SEAL-PS/-MV seals or Schluter ® -KERDI-FIX sealant and bonding compound

10 SHOWER ASSEMBLY — Barrier-free

11 Schluter ramp

® -KERDI-SHOWER-SR

Alternative (not shown):

• Mortar ramp

12 Schluter ® -DITRA uncoupling membrane

Alternative (not shown):

• Schluter ® -KERDI waterproofing membrane

13 Wood or concrete subfloor

14 Schluter ® -DILEX profile (optional)

Bench (not shown):

• Schluter ® -KERDI-SHOWER-SB bench (optional)

• Schluter ® -KERDI-BOARD bench (optional)

Niche (not shown):

• Schluter ® -KERDI-BOARD-SN niche (optional)

Barrier-Free Showers – Ceramic or stone tile

Schluter

-KERDI waterproofing membrane or

Schluter

-KERDI-BOARD waterproof building panel

K-SHBF-15

Areas of Application

Interior showers with barrier-free access.

Over wood or concrete subfloors.

Limitations

Certain glass tiles may not be compatible with bonded waterproof membranes and/or may require special setting materials. Consult glass tile manufacturer and Schluter ® -Systems for more information.

Certain moisture sensitive stones, e.g., green marble, or resin-backed tiles may not be appropriate for use in wet areas such as steam showers or may require special setting materials. Consult stone supplier and

Schluter ® -Systems for more information.

Requirements

Plywood, OSB, or concrete subfloor must be clean, even, and load bearing.

Recessing the floor of a bathroom must be done in a way that preserves the structural integrity and safety of the construction. This may require the services of a qualified design professional (e.g., architect, engineer, etc.).

Base – KERDI-SHOWER-ST/-L/-LS or Portland cement mortar bed.

Ramp – KERDI-SHOWER-SR or Portland cement mortar bed.

Bench –KERDI-SHOWER-SB, KERDI-BOARD, concrete, masonry block, or sawn lumber sheathed with solid backing (see above).

KERDI-DRAIN/-LINE shall be properly supported.

Minimum KERDI-BOARD thickness – 1/2" (12.5 mm) for studs spaced at

16" (40.6 cm) o.c. and 3/4" (19 mm) for studs spaced at 24" (61.0 cm) o.c.

KERDI or KERDI-BOARD shall be installed up to the height of the showerhead at minimum.

KERDI or DITRA shall be installed in all floor areas subject to water exposure (i.e., wet area and drying area). Floor/wall connections shall be sealed with KERDI-BAND.

Any protrusions through the KERDI or KERDI-BOARD (e.g., showerhead, mixing valve, etc.) must be treated with KERDI-SEAL-PS/-MV seals,

KERDI-FIX or suitable sealant.

When using the stainless steel KERDI-DRAIN bonding flange, use

KERDI-FIX to bond KERDI to the drain.

Substrate Preparation

Verify that subfloor panels and solid backing are properly fastened to framing members.

Any leveling of the subfloor must be done prior to installing

KERDI-SHOWER-ST/-L/-LS /-SB/-SR prefabricated substrates.

Solid Backing Materials

Gypsum wallboard – ASTM C1396/C1396M

Cementitious backer unit – ANSI A118.9 or ASTM C1325

Fiber-cement underlayment – ASTM C1288

Fiber-reinforced water-resistant gypsum

backerboard/underlayment – ASTM C1278

Coated glass mat water-resistant gypsum backerboard – ASTM C1178

Portland cement mortar – ANSI A108.1B

Concrete

Masonry

Setting and Grouting Materials

Unmodified thin-set mortar – ANSI A118.1

Grout – ANSI A118.3, A118.6, A118.7

Installation Specifications

Solid backing panels – follow manufacturer’s directions

Portland cement mortar bed – ANSI A108.1B

Tile – ANSI A108.5

Grout – ANSI A108.6, A108.10

Other Considerations

Barrier-free tiled showers rely on the slope of the floor to effectively contain water in the immediate shower area and direct water to the drain.

Given the wide range of potential configurations, it isn’t possible to address them all in this Handbook.

Waterproofing must be installed in all areas subject to water exposure.

Install KERDI over mortar beds and Schluter ® prefabricated EPS foam substrates. Use the DITRA uncoupling membrane over plywood/OSB or concrete subfloors. All seams are sealed using KERDI-BAND. Please refer to the Schluter ® and warranty criteria.

-DITRA Installation Handbook for complete details

If KERDI-LINE is placed at shower entrance, it is recommended that grate assembly A or D is chosen and that the drainage openings span the maximum width of the entrance to limit potential overflow; secondary drainage (e.g., KERDI-DRAIN) may be required in the drying area.

Various building codes and other sources, such as the Americans with

Disabilities Act, include specific requirements for disabled access in public buildings and must be consulted when applicable. Areas of interest may include degree of slope, clearance, and supporting structures such as grab bars.

Shower grab bars must be anchored in the structure or solid blocking behind KERDI-BOARD.

When KERDI-SHOWER-ST/-L/-LS tray dimensions do not match the dimensions of the shower compartment, the tray may be cut or extended with dry pack mortar.

When KERDI or KERDI-BOARD and tile are installed on the ceiling, the solid backing and fasteners must be able to support the load of the tile and setting and grouting materials.

A water test is recommended before setting tile to verify a successful installation. Wait 24 hours minimum after the membrane installation is complete to allow for final set of thin-set mortar and ensure waterproof performance at seams and connections. A temporary dam (e.g., a 2x4 and silicone sealant, plastic sheeting and sand, etc.) must be provided at the threshold to perform the water test.

Schluter ® -Systems profiles may be used to finish and protect outside corners and eliminate the use of sealant at inside corners; see page 35.

SHOWER ASSEMBLY — Barrier-free 11

STEAM SHOWER ASSEMBLY

Intermittent Use Steam Showers – Ceramic or stone tile

Schluter

-KERDI waterproofing membrane

K-SSH-K-15

Ceramic or stone tile

Unmodified thin-set mortar

8 Drain: a.

Schluter ® -KERDI-DRAIN

11 Wood or concrete subfloor

12 Schluter ® -DILEX profile (optional)

Schluter ® -KERDI waterproofing membrane

Schluter ® -KERDI-BAND waterproofing strips

9 b.

Schluter ® -KERDI-LINE

Base: a.

Schluter ® -KERDI-SHOWER-ST

Schluter ® -KERDI-KERECK-F waterproofing corners b.

Schluter ® -KERDI-SHOWER-L/-LS

Schluter ® -KERDI-SEAL-PS/-MV seals or Schluter ® -KERDI-FIX sealant and bonding compound

Alternative (not shown):

• Mortar bed

10 Schluter curb

® -KERDI-SHOWER-SC

Solid backing

Alternatives (not shown):

• Schluter ® -KERDI-BOARD waterproof building panel

• Built-up curb

12 STEAM SHOWER ASSEMBLY — Schluter

-KERDI waterproofing membrane

Bench (not shown):

• Schluter ® -KERDI-SHOWER-SB bench (optional)

• Schluter ® -KERDI-BOARD bench (optional)

Niche (not shown):

• Schluter ® -KERDI-BOARD-SN niche (optional)

Intermittent Use Steam Showers – Ceramic or stone tile

Schluter

-KERDI waterproofing membrane

K-SSH-K-15

Areas of Application

Interior intermittent use steam showers (e.g., residential applications).

Over wood or concrete subfloors.

Areas requiring disabled access/barrier-free applications; see detail

K-SHBF on page 10.

Substrate Preparation

Verify that subfloor panels and solid backing are properly fastened to framing members.

Any leveling of the subfloor must be done prior to installing

KERDI-SHOWER-ST/-L/-LS/-SC/-SB/-SR.

Limitations

Not intended for continuous use steam rooms (e.g., applications in spas, fitness centers, etc.); see detail K-SR on page 16.

Certain glass tiles may not be compatible with bonded waterproof membranes and/or may require special setting materials. Consult glass tile manufacturer and Schluter ® -Systems for more information.

Schluter ® -Systems for more information.

Do not use sawn lumber curbs on concrete subfloors subject to moisture migration.

Solid Backing Materials

Gypsum wallboard – ASTM C1396/C1396M

Cementitious backer unit – ANSI A118.9 or ASTM C1325

Fiber-cement underlayment – ASTM C1288

Fiber-reinforced water-resistant gypsum

backerboard/underlayment – ASTM C1278

Coated glass mat water-resistant gypsum backerboard – ASTM C1178

Portland cement mortar – ANSI A108.1B

Concrete

Masonry

Requirements

Plywood, OSB, or concrete subfloor must be clean, even, and load bearing.

Provide insulation in wall and ceiling cavities to reduce moisture condensation on the tiled surface.

Base – KERDI-SHOWER-ST/-L/-LS or Portland cement mortar bed.

Curb – KERDI-SHOWER-SC, KERDI-BOARD, concrete, masonry block, or sawn lumber sheathed with solid backing (see above).

Bench – KERDI-SHOWER-SB, KERDI-BOARD, concrete, masonry block, or sawn lumber sheathed with solid backing (see above)

KERDI-DRAIN/-LINE shall be properly supported.

Slope ceilings 2" (50 mm) per foot minimum to avoid condensation from dripping onto occupants (may be sloped to center to minimize rundown on walls).

Install KERDI waterproofing membrane on all surfaces, including the ceiling.

Any protrusions through the KERDI membrane (e.g., showerhead, mixing valve, steam inlet, etc.) must be treated with KERDI-SEAL-PS/-MV seals,

KERDI-FIX or suitable sealant.

When using the stainless steel KERDI-DRAIN integrated bonding flange, use KERDI-FIX to bond KERDI to the drain.

Movement joints shall be provided at all changes in plane, including floor/ wall, wall/wall, and wall/ceiling transitions. Schluter ® -Systems prefabricated movement joint profiles (e.g., DILEX-EKE) provide a maintenance-free alternative to sealant; see page 35.

Setting and Grouting Materials

Unmodified thin-set mortar – ANSI A118.1

Grout – ANSI A118.3, A118.6, A118.7

Installation Specifications

Solid backing panels – follow manufacturer’s directions

Portland cement mortar bed – ANSI A108.1B

Tile – ANSI A108.5

Grout – ANSI A108.6, A108.10

Other Considerations

When KERDI-SHOWER-ST/-L/-LS tray dimensions do not match the dimensions of the shower compartment, the tray may be cut or extended with dry pack mortar.

When KERDI and tile are installed on the ceiling, the solid backing and fasteners must be able to support the load of the tile and setting and grouting materials.

Schluter ® -Systems profiles may be used to finish and protect outside corners and eliminate the use of sealant at inside corners; see page 35.

STEAM SHOWER ASSEMBLY — Schluter

-KERDI waterproofing membrane 13

STEAM SHOWER ASSEMBLY

Intermittent Use Steam Showers – Ceramic or stone tile

Schluter

-KERDI-BOARD waterproof building panel

K-SSH-KB-15

10 a

9 a

9 b

10 b

Ceramic or stone tile

Unmodified thin-set mortar

9 Drain: a.

Schluter ® -KERDI-DRAIN

12 Wood or concrete subfloor

13 Schluter ® -DILEX profile (optional)

Schluter ® -KERDI waterproofing membrane

Schluter ® -KERDI-BOARD waterproof building panel

10 b.

Schluter ® -KERDI-LINE

Base: a.

Schluter ® -KERDI-SHOWER-ST

Bench (not shown):

• Schluter ® -KERDI-SHOWER-SB bench (optional)

• Schluter ® -KERDI-BOARD bench (optional)

Schluter washers

® -KERDI-BOARD-ZT

Schluter ® -KERDI-BAND waterproofing strips b.

Schluter ® -KERDI-SHOWER-L/-LS

Alternative (not shown):

• Mortar bed

Niche (not shown):

• Schluter ® -KERDI-BOARD-SN niche (optional)

Schluter ® -KERDI-KERECK-F waterproofing corners

Schluter seals or

® -KERDI-SEAL-PS/-MV

Schluter ® -KERDI-FIX sealant and bonding compound

11 Schluter ® -KERDI-SHOWER-SC curb

Alternatives (not shown):

• Schluter ® -KERDI-BOARD waterproofing panel

• Built-up curb

14 STEAM SHOWER ASSEMBLY — Schluter

-KERDI-BOARD waterproof building panel

Intermittent Use Steam Showers – Ceramic or stone tile

Schluter

-KERDI-BOARD waterproof building panel

K-SSH-KB-15

Areas of Application

Interior intermittent use steam showers (e.g., residential applications).

Over wood or concrete subfloors.

Areas requiring disabled access/barrier-free applications; see detail

K-SHBF on page 10.

Substrate Preparation

Verify that subfloor panels are properly fastened to framing members.

Any leveling of the subfloor must be done prior to installing

KERDI-SHOWER-ST/-L/-LS/-SC/-SB/-SR.

Limitations

Not intended for continuous use steam rooms (e.g., applications in spas, fitness centers, etc.); see detail K-SR on page 16.

Certain glass tiles may not be compatible with bonded waterproof membranes and/or may require special setting materials. Consult glass tile manufacturer and Schluter ® -Systems for more information.

Schluter ® -Systems for more information.

Do not use sawn lumber curbs on concrete subfloors subject to moisture migration.

Solid Backing Materials

Gypsum wallboard – ASTM C1396/C1396M

Cementitious backer unit – ANSI A118.9 or ASTM C1325

Fiber-cement underlayment – ASTM C1288

Fiber-reinforced water-resistant gypsum

backerboard/underlayment – ASTM C1278

Coated glass mat water-resistant gypsum backerboard – ASTM C1178

Portland cement mortar – ANSI A108.1B

Concrete

Masonry

Requirements

Plywood, OSB, or concrete subfloor must be clean, even, and load bearing.

Provide insulation in wall and ceiling cavities to reduce moisture condensation on the tiled surface.

Base – KERDI-SHOWER-ST/-L/-LS or Portland cement mortar bed

Curb – KERDI-SHOWER-SC, KERDI-BOARD, concrete, masonry block, or sawn lumber sheathed with solid backing (see below).

Bench – KERDI-SHOWER-SB, KERDI-BOARD, concrete, masonry block, or sawn lumber sheathed with solid backing (see below).

KERDI-DRAIN/-LINE shall be properly supported.

Slope ceilings 2" (50 mm) per foot minimum to avoid condensation from dripping onto occupants (may be sloped to center to minimize rundown on walls).

Install KERDI waterproofing membrane on base and curb and

KERDI-BOARD waterproof building panel on walls and ceiling.

Minimum KERDI-BOARD thickness – 1/2" (12.5 mm) for studs spaced at

16" (40.6 cm) o.c. and 3/4" (19 mm) for studs spaced at 24" (61.0 cm) o.c.

Any protrusions through the KERDI-BOARD (e.g., showerhead, mixing valve, steam inlet, etc.) must be treated with KERDI-SEAL-PS/-MV seals,

KERDI-FIX or suitable sealant.

When using the stainless steel KERDI-DRAIN bonding flange, use

KERDI-FIX to bond KERDI to the integrated bonding flange.

Setting and Grouting Materials

Unmodified thin-set mortar – ANSI A118.1

Grout – ANSI A118.3, A118.6, A118.7

Installation Specifications

Portland cement mortar bed – ANSI A108.1B

Tile – ANSI A108.5

Grout – ANSI A108.6, A108.10

Other Considerations

When KERDI-SHOWER-ST/-L/-LS tray dimensions do not match the dimensions of the shower compartment, the tray may be cut or extended with dry pack mortar.

Shower grab bars must be anchored in the structure or solid blocking behind KERDI-BOARD.

When KERDI-BOARD and tile are installed on the ceiling, the fasteners must be able to support the load of the tile and setting and grouting materials.

Schluter ® -Systems profiles may be used to finish and protect outside corners and eliminate the use of sealant at inside corners; see page 35.

STEAM SHOWER ASSEMBLY — Schluter

-KERDI-BOARD waterproof building panel 15

STEAM ROOM ASSEMBLY

Continuous Use Steam Rooms – Ceramic or stone tile

Schluter

-KERDI-DS waterproofing membrane

K-SR-15

Ceramic or stone tile

Unmodified thin-set mortar

Schluter ® -KERDI-DS waterproofing membrane

Schluter ® -KERDI-BAND waterproofing strips

Schluter ® -KERDI-KERECK-F waterproofing corners

Schluter ® -KERDI-SEAL-PS seals or Schluter ® -KERDI-FIX sealant and bonding compound

Solid backing

8 Schluter ® -KERDI-DRAIN

Alternative (not shown):

• Schluter ® -KERDI-LINE

9 Mortar bed

10 Schluter curb

® -KERDI-SHOWER-SC

Alternatives (not shown):

• Schluter ® -KERDI-BOARD waterproof building panel

• Built-up curb

11 Schluter ® -KERDI-BOARD bench (optional)

Alternative (not shown):

• Schluter ® -KERDI-SHOWER-SB bench (optional)

12 Wood or concrete subfloor

13 Schluter ® -DILEX profile (optional)

16 STEAM ROOM ASSEMBLY — Schluter

-KERDI-DS waterproofing membrane

Continuous Use Steam Rooms – Ceramic or stone tile

Schluter

-KERDI-DS waterproofing membrane

K-SR-15

Areas of Application

Interior continuous use steam rooms (e.g., applications in spas, fitness centers, etc.).

Over wood or concrete subfloors.

Areas requiring disabled access/barrier-free applications; see detail

K-SHBF on page 10.

Substrate Preparation

Verify that subfloor panels and solid backing are properly fastened to framing members.

Any leveling of the subfloor must be done prior to installing

KERDI-SHOWER-ST/-L/-LS/-SC/-SB/-SR.

Limitations

Certain glass tiles may not be compatible with bonded waterproof membranes and/or may require special setting materials. Consult glass tile manufacturer and Schluter ® -Systems for more information.

Schluter ® -Systems for more information.

When KERDI-BOARD is used, steam room must be operated in a manner such that the maximum service temperature of KERDI-BOARD

(158 °F – 70 °C) is not exceeded.

Gypsum-based solid backing panels shall be limited in use to intermittent use steam showers (e.g., residential applications)

Do not use sawn lumber curbs on concrete subfloors subject to moisture migration.

Solid Backing Materials

KERDI-BOARD

Cementitious backer unit – ANSI A118.9 or ASTM C1325

Fiber-cement underlayment – ASTM C1288

Portland cement mortar – ANSI A108.1B

Concrete

Masonry

Setting and Grouting Materials

Unmodified thin-set mortar – ANSI A118.1

Grout – ANSI A118.3, A118.6, A118.7

Installation Specifications

Solid backing panels – follow manufacturer’s directions

Portland cement mortar bed – ANSI A108.1B

Tile – ANSI A108.5

Grout – ANSI A108.6, A108.10

Requirements

Plywood, OSB, or concrete subfloor must be clean, even, and load bearing.

Provide insulation in wall and ceiling cavities to reduce moisture condensation on the tiled surface.

Solid backing – KERDI-BOARD, cementitious backer unit, fiber-cement underlayment, Portland cement mortar bed, concrete, or masonry.

Base – Portland cement mortar bed.

Curb – KERDI-SHOWER-SC, KERDI-BOARD, concrete, masonry block, or sawn lumber sheathed with solid backing (see above).

Bench – KERDI-BOARD, KERDI-SHOWER-SB, concrete, masonry block, or sawn lumber sheathed with solid backing (see above).

KERDI-DRAIN/-LINE shall be properly supported.

Slope ceilings 2" (50 mm) per foot minimum to avoid condensation from dripping onto occupants (may be sloped to center to minimize rundown on walls).

Minimum KERDI-BOARD thickness – 1/2" (12.5 mm) for studs spaced at

16" (40.6 cm) o.c. and 3/4" (19 mm) for studs spaced at 24" (61.0 cm) o.c.

Maximum allowable on-center fastener spacing is 12" (30 cm) for walls and

6" (15 cm) for ceilings.

Install KERDI-DS waterproofing membrane on all surfaces, including the ceiling.

Any protrusions through the KERDI-DS membrane (e.g., steam inlets, lights, etc.) must be treated with KERDI-SEAL-PS, KERDI-FIX or suitable sealant.

When using the stainless steel KERDI-DRAIN bonding flange, use

KERDI-FIX to bond KERDI-DS to the drain.

Other Considerations

Shower grab bars must be anchored in the structure or solid blocking behind KERDI-BOARD.

When KERDI-DS and tile are installed on the ceiling, the solid backing and fasteners must be able to support the load of the tile and setting and grouting materials.

Schluter ® -Systems profiles may be used to finish and protect outside corners and eliminate the use of sealant at inside corners; see page 35.

STEAM ROOM ASSEMBLY — Schluter

-KERDI-DS waterproofing membrane 17

BATHTUB SURROUND

Bathtub Surround – Ceramic or stone tile

Schluter

-KERDI waterproofing membrane or

Schluter

-KERDI-BOARD waterproof building panel

K-TS-15

1 Ceramic or stone tile

2 Unmodified thin-set mortar

3 Waterproofing: a.

Schluter ® -KERDI waterproofing membrane b.

Schluter ® -KERDI-BOARD waterproof building panel

4 Schluter ® -KERDI-BOARD-ZT washers

5 Schluter ® -KERDI-BAND waterproofing strips

6 Schluter ® -KERDI-KERECK-F waterproofing corners

7 Schluter ® -KERDI-SEAL-PS/-MV seals or Schluter ® -KERDI-FIX sealant and bonding compound

8 Schluter ® -KERDI-FIX sealant and bonding compound

9 Solid backing

10 Schluter ® -DILEX profile (optional)

Niche (not shown):

• Schluter ® -KERDI-BOARD-SN niche (optional)

18 BATHTUB SURROUND

Bathtub surround – Ceramic or stone tile

Schluter

-KERDI waterproofing membrane or Schluter

-KERDI-BOARD waterproof building panel

K-TS-15

Areas of Application

Interior bathtub surrounds.

Limitations

Certain glass tiles may not be compatible with bonded waterproof membranes and/or may require special setting materials. Consult glass tile manufacturer and Schluter ® -Systems for more information.

Certain moisture sensitive stones, e.g., green marble, or resin-backed tiles may not be appropriate for use in wet areas such as bathtub surrounds or may require special setting materials. Consult stone supplier and Schluter ® -Systems for more information.

Solid Backing Materials

Gypsum wallboard – ASTM C1396/C1396M

Cementitious backer unit – ANSI A118.9 or ASTM C1325

Fiber-cement underlayment – ASTM C1288

Fiber-reinforced water-resistant gypsum backerboard/underlayment –

ASTM C1278

Coated glass mat water-resistant gypsum backerboard – ASTM C1178

Portland cement mortar – ANSI A108.1B

Concrete

Masonry

Requirements

Solid backing panels or KERDI-BOARD shall be spaced a minimum of

1/4" (6 mm) from the tub deck.

Minimum KERDI-BOARD thickness – 1/2" (12.5 mm) for studs spaced at

16" (40.6 cm) o.c. and 3/4" (19 mm) for studs spaced at 24" (61 cm) o.c.

KERDI-BOARD shall be fastened to wood or metal framing with screws and corresponding Schluter ® -KERDI-BOARD-ZT washers. Screws must reach a depth of at least 3/4" (20 mm) in wood studs and 3/8" (10 mm) in metal studs. Maximum allowable on-center fastener spacing is

12" (30 cm) for walls and 6" (15 cm) for ceilings.

KERDI waterproofing membrane or KERDI-BOARD waterproof building panel shall be installed up to the height of the showerhead at minimum.

Any protrusions through the KERDI membrane or KERDI-BOARD panel

(e.g., showerhead, mixing valve, etc.) must be treated with

KERDI-SEAL-PS/-MV seals, KERDI-FIX or suitable sealant.

Setting and Grouting Materials

Unmodified thin-set mortar – ANSI A118.1

Grout – ANSI A118.3, A118.6, or A118.7

Installation Specifications

Solid backing panels – follow manufacturer’s instructions

Portland cement mortar bed – ANSI A108.1B

Tile – ANSI A108.5

Grout – ANSI A108.6, A108.10

Other Considerations

When KERDI or KERDI-BOARD and tile are installed on the ceiling, the solid backing and fasteners must be able to support the load of the tile and setting and grouting materials.

Shower grab bars must be anchored in the structure or solid blocking behind KERDI-BOARD.

Schluter ® -Systems profiles may be used to finish and protect outside corners and eliminate the use of sealant at inside corners; see page 35.

Substrate Preparation

When using KERDI waterproofing membrane, verify that solid backing is properly fastened to framing members.

BATHTUB SURROUND 19

INSTALLATION

Walls and Ceilings

Please refer to Schluter ® -Systems' installation videos in addition to reading the instructions below.

Shower walls may be made waterproof using KERDI/-KERDI-DS or KERDI-BOARD prior to construction of the shower base.

The waterproofing is carried to the height of the showerhead (at minimum). KERDI or KERDI-BOARD application on ceiling is optional for showers.

For continuous-use steam rooms, KERDI-DS is applied to walls and ceilings. For intermittent use steam showers, KERDI or KERDI-BOARD is applied to walls and ceilings.

Schluter

-KERDI or Schluter

-KERDI-DS over solid backing

The thin-set mortar used for bonding KERDI/-KERDI-DS to walls and ceilings must be appropriate for the substrate and must penetrate and engage the membrane fleece. For most substrates (e.g., gypsum board or CBU), an unmodified thin-set mortar is used. The mortar must be mixed to a fairly fluid consistency, but still able to hold a notch.

1 Clean any dust or other debris from the surface of the solid backing. Dampen particularly dry and porous substrates in order to help prevent premature drying or skinning of the thin-set mortar.

2 Apply unmodified thin-set mortar using a

1/4" x 3/16" (6 mm x 5 mm) V-notched trowel or the KERDI-TROWEL. Embed

KERDI or KERDI-DS in the mortar and work the membrane onto the entire surface to ensure full coverage and remove air pockets.

KERDI-SEAL-PS/-MV

Seams in the membrane are constructed by overlapping the edges by 2" (50 mm) or by abutting adjacent sheets and installing

KERDI-BAND, centered over the joint.

Any protrusions through the membrane

(e.g., mixing valve, shower head, etc.) must be sealed with KERDI-SEAL-PS/-MV,

KERDI-FIX, or other suitable sealant.

Schluter

-KERDI-BOARD over wood or metal framing

Grab bars, wall-mounted toilets, or other heavy objects must be anchored in the structure or solid blocking behind KERDI-BOARD. Installation instructions for other applications of KERDI-BOARD (e.g. fully embedded or spot-bonded over solid backing) can be found in the 12.1 Schluter ® -KERDI-BOARD technical data sheet.

1 KERDI-BOARD can be mounted vertically or horizontally on framing with appropriate screws and corresponding KERDI-BOARD-ZT washers. Minimum board thickness = 1/2"

(12.5 mm) for studs spaced at 16" (40.6 cm) o.c.; 3/4" (19 mm) for studs spaced at 24"

(61.0 cm) o.c. Screws must reach a depth of at least 3/4" (20 mm) in wood studs and at least 3/8" (10 mm) in metal studs.

2 Abut panels over the center of the studs.

Screws may be placed between adjacent panels such that the washers fasten both panel edges. The maximum allowable on-center fastener spacing is 12" (30 cm) for walls and 6" (150 mm) for ceilings.

KERDI-SEAL-PS/-MV

KERDI-BOARD joints, corners, and fastener penetrations are sealed with KERDI-BAND and KERDI-KERECK corners, ensuring a minimum 2" (50 mm) overlap. Apply unmodified thin-set mortar using a 1/4" x 3/16"

(6 mm x 5 mm) V-notched trowel or the

KERDI-TROWEL. Embed KERDI-BAND/-

KERECK in the mortar and work the membrane onto the surface to ensure full coverage and remove air pockets. Any protrusions through the panel (e.g., mixing valve, shower head, etc.) must be sealed with

KERDI-SEAL-PS/-MV, KERDI-FIX, or other suitable sealant.

20 INSTALLATION — Walls and Ceilings

INSTALLATION

Schluter

®

-KERDI-BOARD-SN Shower Niche

Please refer to Schluter ® -Systems' installation videos in addition to reading the instructions below.

The exact order of installation can vary from that shown below, provided all fastening and waterproofing measures are performed properly. The following represents Schluter ® -Systems' recommendations for simple and reliable installation.

Schluter

-KERDI over solid backing

1 Determine desired location and trace around the outside of the KERDI-BOARD-SN flange, making sure the lines are level and plumb.

Cut and remove the wallboard such that the niche will be supported on both sides by the studs or other wall framing.

2 Insert the niche and fasten to the studs using wood or metal screws, placing the fasteners approximately 1/4" (6 mm) from the edges of the niche. Fasten all corners and limit fastener spacing to 12" (30 cm) o.c.

3 Apply the KERDI membrane over the wall surface as described on page 20. Once the membrane is solidly embedded, cut the membrane to match the niche opening.

Schluter

-KERDI-BOARD over wood or metal framing

1 Determine desired location and trace around the outside of the KERDI-BOARD-SN flange, making sure the lines are level and plumb.

Cut and remove the KERDI-BOARD such that the niche will be supported on both sides by the studs or other wall framing.

2 Insert the niche and fasten to the studs using wood or metal screws and KERDI-BOARD-ZT washers, placing the fasteners along the seam between the KERDI-BOARD and the niche.

Fasten all corners and limit fastener spacing to

12" (30 cm) o.c.

3 Seal the seams between the niche and walls using KERDI-BAND with unmodified thin-set mortar ensuring a 2" (50 mm) overlap in all directions.

Note: When using the prefabricated shelf, determine the desired height of the shelf and mark with a level line. Set tile up to that line on the back and sides of the niche. Butter the sides and back of the shelf with unmodified thin-set mortar and solidly embed it in the niche, resting on the previously installed tile.

The shelf may be raised at the back to create a slope, or the tile may be set on a slope, to prevent water from pooling in the finished application.

INSTALLATION — Schluter

-KERDI-BOARD-SN Shower Niche 21

INSTALLATION

Shower Base with Schluter

®

-KERDI-DRAIN

Please refer to Schluter ® -Systems' installation videos in addition to reading the instructions below.

Preparation

Locate and cut a hole in the substrate for the drain outlet and coupling to the waste line using the template provided. Limit the diameter of the hole to

5" (125 mm) maximum to ensure proper support for the tile assembly. Note: Fill in box-outs in concrete floors with dry-pack mortar or concrete. A pipe coupling or similar can be used as a form around the waste line.

Schluter

-KERDI-DRAIN with Schluter

-KERDI-SHOWER-ST prefabricated shower tray

The substrate must be clean, even, and load bearing. Any leveling must be done prior to shower tray installation. If necessary, cut the tray to size prior to application; ideally, the tray is cut equally on all sides to ensure a consistent perimeter height. The base can also be extended beyond the tray using dry-pack mortar.

Plumbing Access: If there is access to the plumbing from below and the waste line can be connected after installing KERDI-DRAIN, the tray can be installed prior to the drain.

1 Apply unmodified thin-set mortar to the substrate using a 1/4" x 3/8" (6 mm x 10 mm) square- or U-notched trowel.

2 Place the KERDI-SHOWER-ST tray and solidly embed in the mortar. Check the underside of the tray to ensure full coverage and support are achieved.

3 Completely fill the step in the shower tray with thin-set mortar. Press KERDI-DRAIN firmly into the mortar to ensure full support of the bonding flange.

No Plumbing Access: When there is no access to the plumbing from below, KERDI-DRAIN is installed to the appropriate height and connected to the waste line prior to the installation of the shower tray.

1 Begin by dry-fitting the components.

Measure and cut a section of pipe to connect

KERDI-DRAIN to the odor trap using the detachable center section of the tray or foam spacers included with the drain as a spacer. Prepare the odor trap, pipe, and

KERDI-DRAIN with cleaner, primer and ABS or PVC cement per the solvent cement manufacturer’s instructions and connect.

2 Apply thin-set mortar to the substrate and to the top and bottom of the detached center section of the KERDI-SHOWER-ST tray.

Slide the center section into place below the drain to ensure solid and uniform support of the bonding flange.

3 Apply unmodified thin-set mortar to the substrate using a 1/4" x 3/8" (6 mm x 10 mm) square- or U-notched trowel. Place the

KERDI-SHOWER-ST tray and solidly embed in the mortar. Check the underside of the tray to ensure full coverage and support are achieved.

22 INSTALLATION — Shower base with Schluter

-KERDI-DRAIN

Clamping Ring Drain Installed: If a clamping ring drain is installed, replace with KERDI-DRAIN or convert using the KERDI-DRAIN adaptor kit.

1 Remove the clamping ring from the installed drain and save the bolts. Align the bolt pattern of the clamping ring with the adaptor ring and punch the matching inserts through the adaptor ring.

2 Apply a 1/4" - 3/8" (6 mm - 10 mm) bead of KERDI-FIX to the installed drain flange.

Place the adaptor ring on the installed drain, re-insert the bolts, and tighten evenly. Make bolts finger-tight plus 1/4 turn; over tightening may warp the ring and result in leaks.

3 Slide the adaptor flange into the adaptor ring and ensure full support underneath with mortar or the detachable center section of the foam tray. Depending on the installed drain elevation, it may be necessary to install a polystyrene foam panel, tile backerboard, etc. prior to the tray. Install the tray as per the instructions on page 22.

Note: Schluter ® -Systems recommends a leak test be performed on the connection between the drain and the waste line prior to continuing with the remainder of the installation whenever possible.

Schluter

-KERDI-DRAIN with mortar bed

Plumbing Access: If there is access to the plumbing from below and the waste line can be connected after installing KERDI-DRAIN, the drain can be installed in conjunction with the mortar bed.

1 Place a ring of loose mortar up to the inlet hole in the floor and firmly press the drain into the mortar. The bonding flange must be fully supported to prevent damage to the tile assembly

(e.g., cracked grout around drain). When installing KERDI-DRAIN over wood substrates, the minimum thickness of mortar required at the perimeter of the bonding flange is 1" (25 mm).

2 The screed is then placed flush with the top of the bonding flange of the KERDI-DRAIN.

Slope the mortar bed at 1/4" (6 mm) per

12" (305 mm) using the bonding flange and a perimeter screed as guides.

1 Measure and cut a section of pipe to connect KERDI-DRAIN to the odor trap using the foam spacers included with the drain as a spacer. When installing KERDI-DRAIN over wood substrates, the minimum thickness of mortar required at the perimeter of the bonding flange is

1" (25 mm). Prepare the odor trap, cut section of pipe, and KERDI-DRAIN with cleaner, primer and ABS or PVC cement per the solvent cement manufacturer’s instructions and connect.

2 Pack loose mortar under the drain up to the inlet hole to ensure solid and uniform support of the bonding flange. The mortar bed is then placed according to the instructions above.

INSTALLATION — Shower base with Schluter

-KERDI-DRAIN 23

Clamping Ring Drain Installed: If a clamping ring drain is installed, replace with KERDI-DRAIN or convert using the KERDI-DRAIN adaptor kit.

1 Remove the clamping ring from the installed drain and save the bolts. Align the bolt pattern of the clamping ring with the adaptor ring and punch the matching inserts through the adaptor ring.

2 Apply a 1/4" - 3/8" (6 mm - 10 mm) bead of KERDI-FIX to the installed drain flange.

Place the adaptor ring on the installed drain, re-insert the bolts, and tighten evenly.

Make bolts finger-tight plus 1/4 turn; over tightening may warp the ring and result in leaks.

3 Slide the adaptor flange into the adaptor ring and ensure full support under the adaptor flange with mortar. The mortar bed is then placed according to the instructions on page 23.

Note: Schluter ® -Systems recommends a leak test be performed on the connection between the drain and the waste line prior to continuing with the remainder of the installation whenever possible.

Schluter

-KERDI-SHOWER-SC/-SR shower curb or ramp

If necessary, cut the KERDI-SHOWER-SC/-SR curb or ramp to length using a handsaw.

1 Apply unmodified thin-set mortar to the floor and to the edge of the shower base and walls using a 1/4" x 3/8" (6 mm x 10 mm) square- or U-notched trowel.

2 Press the curb or ramp firmly into place.

Check the underside of the curb or ramp to ensure that full coverage and support is achieved.

Note: Schluter ® -KERDI-BOARD can be used to build custom curbs, which are installed similar to

KERDI-SHOWER-SC.

Waterproofing the shower base

The KERDI or KERDI-DS waterproofing membranes can be installed over the KERDI-SHOWER-ST tray immediately or over a mortar bed as soon as the mortar bed can be walked upon using unmodified thin-set mortar. The thin-set mortar must be mixed to a fairly fluid consistency, but still able to hold a notch.

1 Apply unmodified thin-set mortar to the bonding flange and surrounding shower base with a

1/4" x 3/16" (6 mm x 5 mm) V-notched trowel or the KERDI-TROWEL. Note: When using the stainless steel drain, the membrane is adhered to the bonding flange with KERDI-FIX; clean the bonding flange prior to KERDI-FIX application.

2 Embed KERDI or KERDI-DS in the bond coat and work the membrane onto the

KERDI-DRAIN bonding flange and shower base to ensure full coverage and remove air pockets.

The membrane is carried to the step in the bonding flange (template provided) and to the edges of the shower base.

24 INSTALLATION — Shower base with Schluter

-KERDI-DRAIN

3 Repeat the process to install the membrane over the curb or ramp. Seams in the membrane are constructed by overlapping the edges by 2" (50 mm) or by abutting adjacent sheets and installing KERDI-BAND centered over the joint. Install KERDI-KERECK at all inside and outside corners.

Grate assembly

Grate:

1 Place the height adjustment collar inside the lateral adjustment ring and snap the grate into place. Note: For the 6" (150 mm) grates, the height adjustment collar is integrated with the grate. For the residential adaptor kit, there is no lateral adjustment ring.

2 Fill the step in the bonding flange with thin-set mortar and back-butter the underside of the grate to ensure full support. Place the assembly into the mortar and install the surrounding tiles, ensuring full coverage.

3 Position the grate to match the joint pattern of the tile covering and press flush with the tile surface. Remove all excess setting material immediately. Note: Protect the visible surface of the grate from contact with setting and grouting materials. In particular, anodized aluminum is sensitive to alkaline materials.

Tileable Covering Support:

1 Fill the step in the bonding flange with thin-set mortar. Place the tile spacer in the lateral adjustment ring and press the assembly into the mortar. Install tiles up to the tile spacer, ensuring full coverage. Embed the tiles on the integrated tabs on the lateral adjustment ring, which provide for a flush transition to the covering support. Position the tile spacer to match the joint pattern of the tile covering.

The tiles may be held back from the spacer as required to match the layout. Remove all excess setting material.

2 Apply tile to the top of the covering support using unmodified thin-set mortar. The tile may overhang the covering support provided that a drainage opening of at least 3/16"

(5 mm) is provided.

3 After the tile is set and grouted, remove the tile spacer and insert the tiled covering support into the lateral adjustment ring.

INSTALLATION — Shower base with Schluter

-KERDI-DRAIN 25

INSTALLATION

Shower base with Schluter

®

-KERDI-LINE

Please refer to Schluter ® -Systems installation videos in addition to reading the instructions below.

Preparation

Locate and cut a hole in the substrate for the drain outlet and coupling to the waste line using the template provided. Limit the diameter of the hole to

Schluter

-KERDI-LINE channel body installation

Plumbing Access: When there is access to the plumbing from below and the waste line can be connected after installing KERDI-LINE, the channel body may be set without making a connection to the waste line simultaneously.

Apply unmodified thin-set mortar to the substrate where the drain is to be placed with a notched trowel and solidly embed the channel support in the mortar.

Apply unmodified thin-set mortar to the top of the channel support and press the channel body firmly into the mortar, ensuring full support of the bonding flange. Check to make sure the KERDI-LINE is level.

No Plumbing Access: When there is no access to the plumbing from below, the channel body must be set and connected to the waste line simultaneously.

Begin the drain installation by dry fitting the components. Measure and cut a section of pipe to connect the coupling to the odor trap below the floor, using the channel support as a spacer.

Apply unmodified thin-set mortar to the top of the channel support with a notched trowel and press the channel support firmly onto the underside of the channel body.

Attach the mechanical coupling to the drain outlet and the cut section of the pipe per the coupling manufacturer’s instructions.

Apply unmodified thin-set mortar to the substrate where the drain is to be placed with a notched trowel. Prepare the cut section of pipe and odor trap with cleaner, primer and ABS or PVC cement per the solvent cement manufacturer’s instructions.

Solidly embed the channel support and KERDI-LINE into the mortar on the floor and connect the cut section of pipe to the odor trap. Check to make sure the KERDI-LINE is level.

Note: KERDI-FIX or other adhesives that are compatible with EPS foam can be used to install the channel support and channel body as an alternative to thin-set mortar. Apply a generous bead of

KERDI-FIX to the top and bottom of the channel support. The use of KERDI-FIX limits the ability to level KERDI-LINE.

Note: Schluter ® -Systems recommends a leak test be performed on the connection between the drain and the waste line prior to continuing with the remainder of the installation whenever possible.

Clamping Ring Drain Installed: If a clamping ring drain is already installed, the drain must be replaced with KERDI-LINE.

26 INSTALLATION — Shower base with Schluter

-KERDI-LINE

Schluter

-KERDI-LINE with Schluter

-SHOWER-L/-LS prefabricated tray

1 Any leveling of the floor must be done prior to the installation of the shower tray.

If necessary, cut the tray to size prior to application. The shower base can also be extended beyond the tray using dry-pack mortar, which is in turn covered with the

KERDI membrane.

2 Cut the flat end of the KERDI-SHOWER-L/-LS tray to fit around the channel support. Apply unmodified thin-set mortar to the substrate using a 1/4" x 3/8" (6 mm x 10 mm) square- or

U-notched trowel. Slide the KERDI-SHOWER-L/-LS under the edge of the channel body flush with the surface of the channel support, making certain to solidly embed the tray in the mortar. Check the underside of the tray to ensure that full coverage is achieved.

Note: When KERDI-LINE is placed at an intermediate location (e.g., center of shower), it is recommended that the KERDI SHOWER-L tray be cut by equal amounts from the ends to ensure a consistent height of the first course of tile. When KERDI-LINE is placed adjacent to a wall, cut the KERDI-SHOWER-LS tray from the thicker end to ensure a flush transition at the drain.

Schluter

-KERDI-LINE with m ortar base

Place a mortar screed opposite the installed

KERDI-LINE channel body.

Fill the remainder of the shower base with mortar and slope the mortar bed at 1/4"

(6 mm) per 12" (305 mm) using the bonding flange and a perimeter screed as guides.

As soon as the mortar bed can be walked upon, waterproofing with the

KERDI membrane can begin.

Schluter

-KERDI-SHOWER-SC/-SR shower curb or ramp

If necessary, cut the KERDI-SHOWER-SC/-SR curb or ramp to length using a handsaw.

1 Apply unmodified thin-set mortar to the floor and to the edge of the shower base and walls using a 1/4" x 3/8" (6 mm x 10 mm) square- or U-notched trowel.

Press the curb or ramp firmly into place.

Check the underside of the curb or ramp to ensure that full coverage and support is achieved.

Note: KERDI-BOARD can be used to build custom curbs, which are installed similar to

KERDI-SHOWER-SC.

INSTALLATION — Shower base with Schluter

-KERDI-LINE 27

Waterproofing the shower base

The KERDI-SHOWER-L/-LS trays are provided with integral waterproofing. When using a mortar bed, the shower base must be made waterproof using the

KERDI or KERDI-DS waterproofing membrane. The membranes can be installed as soon as the mortar bed can be walked upon.

Apply unmodified thin-set mortar to the shower base with a 1/4" x 3/16"

(6 mm x 5 mm) V-notched trowel or the

KERDI-TROWEL. The thin-set mortar must be mixed to a fairly fluid consistency, but still able to hold a notch.

Embed KERDI or KERDI-DS in the bond coat and work the membrane onto the entire surface to ensure full coverage and remove air pockets. The membrane is carried to the stainless steel bonding flange and to the edges of the shower base.

3 Seams in the membrane are constructed by overlapping the edges by 2" (50 mm) with unmodified thin-set mortar or by abutting adjacent sheets and installing KERDI-BAND with unmodified thin-set mortar, centered over the joint.

4 The KERDI collar on KERDI-LINE is integrated with the adjoining waterproofing assembly using unmodified thin-set mortar. The KERDI collar must be cut and folded where the

KERDI-LINE is installed adjacent to walls.

5 Repeat the process to install the membrane over the curb or ramp. Seams in the membrane are constructed by overlapping the edges by

2" (50 mm) or by abutting adjacent sheets and installing KERDI-BAND centered over the joint. Install KERDI-KERECK at all inside and outside corners.

28 SHOWER ASSEMBLY — Shower base with Schluter

-KERDI-LINE

Grate assembly

Grates A and B

Apply unmodified thin-set mortar to the underside of the grate frame and place it in the channel body ensuring full coverage and support of the frame. Insert the foam spacers in the grate frame to reinforce it during the remainder of the installation.

Insert the plastic height adjustment spacers with threaded bolts under the tabs along the inside of the grate frame to adjust the elevation of the frame such that the surface of the frame will be flush with the surface of the tile covering. The spacers may be adjusted simply by turning the bolts by hand.

3 Install the tiles on the shower base using unmodified thin-set mortar, ensuring full coverage. Make final adjustments to ensure the grate frame is flush with the surrounding tiles.

Note: Protect the visible surfaces of the grate frame and grate from contact with setting and grouting materials. Setting and grouting materials must be removed immediately.

Covering support D

1 Peel the protective foil off the cover strip and adhere the strip to the bonding flange adjacent to the wall(s). Position the strip along the edge of the channel. The cover strip hides and protects the KERDI surface under the tile installed in step 3.

When the shower base will be tiled beyond the ends of the channel, the cover strip is not required at these locations.

2 Insert the tile spacers into the channel body.

Install the surrounding tile on the adjoining walls and shower base up to the spacers using unmodified thin-set mortar, ensuring full coverage. Remove all excess setting material.

3 Tile is installed flush with the front side of the covering support to provide the drainage opening and overhanging the back side of the covering support to cover the bonding flange along the wall using unmodified thinset mortar. When the ends of the channel body are located adjacent to walls, the tile is installed overhanging the end of the support to cover the bonding flange along the walls. Measure and cut the tile such that an approximate 1/16" (1 mm) gap is left at the walls.

Note: When the shower base is tiled beyond the ends of the channel, the tile on the ends of the covering support can be cut to either match the grout joints of the surrounding floor covering or to provide a perimeter drainage opening.

SHOWER ASSEMBLY — Shower base with Schluter

-KERDI-LINE 29

Optional Schluter

-SHOWERPROFILE-S/-R system profiles

Select SHOWERPROFILE-S according to shower base tile thickness and the height and length of the wall area to be covered. Select SHOWERPROFILE-R according to the height of the wall area to be covered.

SHOWERPROFILE-S

1 Measure the height of the area to be covered at the lowest point. Next, measure the length of the area and mark the profile where it is to be cut at both ends. Remove the protective foil and cut the tapered profile and support section to length

2 Place the tapered profile into the support section and apply unmodified thin-set mortar to the fleece on the back side of the profile.

3 Press the profile into place and align it flush with the wall tile. Immediately clean away any excess setting material. Install adjacent tiles on the shower base.

SHOWERPROFILE-R

1 Measure the length of the area to be covered. Remove the protective foil and cut the profile to length.

2 Connect the two components of

SHOWERPROFILE-R to achieve the desired height. Small pieces of tape can be used to help maintain the position of the components during installation.

3 Apply unmodified thin-set mortar to the fleece on the back side of the profile. Press the profile into place and align it flush with the wall tile. Immediately clean away any excess setting material.

Note: The Schluter ® -PROCUT-TSM cutting wheel can be used with an angle grinder set to low speed to cut the stainless steel profiles. The

SHOWERPROFILE-S support section can be cut with snips. Please read and follow all safety instructions from the grinder manufacturer to prevent injury.

Schluter

-KERDI-LINE-FC

KERDI-LINE-FC may be used with tiles that are 1/4" (6 mm) thick or greater.

35 mm - 1-3/8''

1 Install KERDI-LINE channel bodies end-to-end and overlap the KERDI collars using unmodified thin-set mortar to ensure a waterproof connection.

2 Apply a sufficient amount of thin-set mortar to the substrate and/or the back of

KERDI-LINE-FC and press the profile into the mortar until its surface is flush with the adjacent tile and grate assembly. Leave a space of approximately 1/16" – 1/8"

(1.5 – 3 mm). Fill the joints completely with grout or setting material.

30 SHOWER ASSEMBLY — Shower base with Schluter

-KERDI-LINE

INSTALLATION

Bathtub surround

Please refer to Schluter ® -Systems' installation videos in addition to reading the instructions below.

The waterproofing is carried to the height of the showerhead (at minimum). KERDI or KERDI-BOARD application on ceiling is optional for bathtub surrounds.

Schluter

-KERDI over solid backing

The thin-set mortar used for bonding KERDI to walls and ceilings must be appropriate for the substrate and must penetrate and engage the membrane fleece. For most substrates (e.g., gypsum board or CBU), an unmodified thin-set mortar is used. The mortar must be mixed to a fairly fluid consistency, but still able to hold a notch.

Clean any dust or other debris from the surface of the solid backing. Dampen particularly dry and porous substrates in order to help prevent premature drying or skinning of the thin-set mortar.

Place painter’s tape to protect the tub deck.

Apply unmodified thin-set mortar to the solid backing using a 1/4" x 3/16" (6 mm x 5 mm) V-notched trowel or the KERDI-

TROWEL. Completely fill the 1/4" (6 mm)wide gap between the solid backing and tub with KERDI-FIX or other suitable sealant.

Note: When the solid backing is installed above the tub flange, apply KERDI-FIX to the tub flange and spread using a small notched trowel.

Apply KERDI-BAND waterproofing strips or

5" (125 mm)-wide cut sections of KERDI waterproofing membrane. Solidly embed the membrane in the mortar and KERDI-FIX to ensure full coverage and remove air pockets.

Apply unmodified thin-set mortar to the solid backing and previously applied

KERDI-BAND. Embed the KERDI in the thin-set mortar and work the membrane onto the entire surface to ensure full coverage and remove air pockets.

Seams in the membrane are constructed by overlapping the edges of KERDI by

2" (50 mm) or by abutting adjacent sheets of

KERDI and installing KERDI-BAND, centered over the joint.

KERDI-SEAL-PS/-MV KERDI-FIX

Any protrusions through the KERDI membrane

(e.g., mixing valve, shower head, etc.) must be sealed with KERDI-SEAL-PS/-MV, KERDI-FIX, or other suitable sealant.

7 Seal connections to knee walls using

KERDI-KERECK-F preformed corners and unmodified thin-set mortar.

Note: See page 21 for KERDI-BOARD-SN shower niche installation instructions.

8 Once the entire membrane, including seams, corners, and knee walls have been completely bonded and, therefore, waterproofed, the assembly is ready to be tiled.

INSTALLATION — Bathtub surround — Schluter

-KERDI 31

Schluter

-KERDI-BOARD over wood or metal framing

Grab bars or other heavy objects must be anchored in the structure or solid blocking behind KERDI-BOARD. Installation instructions for other applications of KERDI-BOARD (e.g. fully embedded or spot-bonded over solid backing) can be found in the 12.1 Schluter ® -KERDI-BOARD technical data sheet.

KERDI-BOARD can be mounted vertically or horizontally on framing with appropriate screws and corresponding

KERDI-BOARD-ZT washers. Minimum board thickness = 1/2" (12.5 mm) for studs spaced at 16" (40.6 cm) o.c.; 3/4" (19 mm) for studs spaced at 24" (61.0 cm) o.c. Screws must reach a depth of at least 3/4" (20 mm) in wood studs and at least 3/8" (10 mm) in metal studs.

Abut panels over the center of the studs or other solid backing. Screws may be placed between adjacent panels such that the washers fasten both panel edges. The maximum allowable on-center fastener spacing is 12" (30 cm) for walls and

6" (150 mm) for ceilings.

Place painter’s tape to protect the tub deck.

Apply unmodified thin-set mortar to the

KERDI-BOARD using a 1/4" x 3/16"

(6 mm x 5 mm) V-notched trowel or the KERDI-TROWEL. Completely fill the

1/4" (6 mm)-wide gap between the

KERDI-BOARD and tub with KERDI-FIX or other suitable sealant.

Note: When KERDI-BOARD is installed above the tub flange, apply KERDI-FIX to the tub flange and spread using a small notched trowel.

Apply KERDI-BAND waterproofing strips.

Solidly embed the membrane in the mortar and KERDI-FIX to ensure full coverage and remove air pockets.

5 KERDI-BOARD joints, corners, and fastener penetrations are sealed with KERDI-BAND, ensuring a minimum 2" (50 mm) overlap.

KERDI-SEAL-PS/-MV

6 Any protrusions through the panel

(e.g., mixing valve, shower head, etc.) must be sealed with KERDI-SEAL-PS/-MV,

KERDI-FIX, or other suitable sealant.

7 Seal connections to knee walls using

KERDI-KERECK-F preformed corners and unmodified thin-set mortar.

Note: See page 21 for KERDI-BOARD-SN shower niche installation instructions.

8 Once all seams, corners, and knee walls have been completely sealed, the assembly is waterproofed and ready to be tiled.

32 INSTALLATION — Bathtub surround — Schluter

-KERDI-BOARD

BARRIER-FREE SHOWERS

Accessibility and style

As our population ages, there is increasing demand for accessible living spaces. Tiled showers typically feature curbs to retain water in the stall, which can make entry difficult for those with limited mobility, including individuals who need the assistance of wheelchairs.

Barrier-free tiled showers eliminate the use of a curb and rely on the slope of the floor to keep water inside the stall, thus improving accessibility. These showers have also become increasingly popular for their aesthetic benefits, as they can integrate seamlessly with surrounding tiled surfaces to enhance an already luxurious environment.

DESIGN AND INSTALLATION CONSIDERATIONS

The Schluter ® -Shower System provides a simple and effective means of waterproofing barrier-free installations. The key to this is that the

KERDI waterproofing membrane is topically applied. Once the slope to the drain is established, KERDI and tile are installed, thus minimizing the thickness of the assembly.

Barrier-free tiled showers rely on the slope of the floor to effectively contain water in the immediate shower area and direct water to the drain. Given the wide range of potential configurations, it isn’t possible to address them all in this Handbook. However, the following guidelines will assist in planning any barrier-free installation.

Ideally, the floor will be recessed before installing a sloped mortar bed or the KERDI-SHOWER-ST shower tray to allow an even transition at the door threshold. This can be relatively straightforward in new construction and can also be accomplished in renovations. When recessing the floor is not an option, it is necessary to provide a ramp up into the shower area. The KERDI-SHOWER-ST/-SR tray and ramp can be useful tools in such applications as well.

Please note that recessing the floor of a bathroom must be done in a way that preserves the structural integrity and safety of the construction. This may require the services of a qualified design professional (e.g., architect, engineer, etc.).

Waterproofing must be installed in all areas subject to water exposure. Ideally, the entire floor is protected. Install KERDI over mortar beds and Schluter ® -Systems prefabricated EPS foam substrates. Use the DITRA uncoupling membrane over plywood/OSB or concrete subfloors. All seams are sealed using KERDI-BAND. Please see detail K-SHBF on page 10 for further discussion.

Note on Accessibility Guidelines:

Various building codes and other sources, such as the Americans with Disabilities Act, include specific requirements for disabled access in public buildings and should be consulted when applicable. Areas of interest may include degree of slope, clearance, and supporting structures such as grab bars.

BARRIER-FREE SHOWERS — Accessibility and style 33

THE WATERPROOF BATHROOM

Security and utility

Bathrooms are a primary focus of today’s building and remodeling projects and are becoming more and more luxurious, complete with steam showers, oversized bathtubs, and the latest in fixtures and lighting. As such, tiled showers, bathtub surrounds, floors, walls, and vanities are in high demand. Tile and stone are beautiful, durable, and available in a wide range of formats, colors, and textures, allowing limitless design options. Tile and stone offer unmatched utility and high-end appeal, making them the ideal surface coverings for bathrooms. Given the substantial investments made in these projects and nature of use, long-term durability is a high priority.

DITRA

KERDI

Waterproofing is the foundation of successful tiled bathrooms. Moisturesensitive construction materials (e.g., wood framing, plywood and OSB sheathing, gypsum wallboard, etc.) are common in the North American building environment and must be protected in wet areas. Wet areas also bring the potential for mold growth if effective moisture management is not provided. The key to mold control is moisture control.

In addition to showers and tub surrounds, bathroom floors surrounding these fixtures are routinely subjected to water exposure during use.

Bathroom floors may also, through unexpected circumstances, become exposed to significant amounts of water; for example, an overflowed toilet or ruptured sink supply, which can result in flooding. Waterproofing these floors can save an owner from replacing the tile assembly and substructure in the event of a leak.

Schluter ® -Systems offers simple and effective solutions to protect moisture-sensitive substrates, prevent mold growth, and preserve the integrity of the tiled surface throughout the bathroom.

The Schluter ® -Shower System is an integrated family of products that together form a fully bonded, watertight assembly for tiled showers and bathtub surrounds. DITRA is an uncoupling membrane that protects the tiled floors from damage by neutralizing differential movement stresses between the substrate and tile and provides reliable waterproofing. Since both of these systems are based on topically-applied, bonded waterproof membranes, they can be combined simply and easily to provide waterproofing throughout the bathroom.

Floors can be made fully waterproof with DITRA. Since the membrane is made of waterproof polyethylene, the only extra step necessary is to seal the seams and floor/wall connections with KERDI-BAND. The same practice is used to integrate the DITRA with the KERDI used to waterproof the shower or tub surround. The result is a comprehensive waterproofing system that protects against moisture penetration.

Please consult the Schluter ® -DITRA Installation Handbook for comprehensive installation guidelines and warranty criteria.

Schluter ® -DITRA Installation Handbook

Complete details and illustrations for tile installations over various substrates, and supplementary information on topics such as waterproofing, movement joints, and thin-set mortars.

To obtain or download a free copy of the DITRA

Installation Handbook, visit www.schluter.com or call 1-800-472-4588 (US) or 1-800-667-8746 (CAN).

34 THE WATERPROOF BATHROOM — Security and utility

PROFILES

Details make the difference

Ceramic and stone tiles are durable, easy to maintain, and hygienic, representing the ideal surface coverings for showers and bathtub surrounds. Exposed tile edges, however, are unsightly and prone to cracking and chipping. While ceramic trim pieces such as bullnose or quarter round have traditionally been used to finish and protect tile edges at the outside corners and perimeters of an installation, ceramic trim availability can be limited, particularly in imported tile lines, which can in turn limit overall tile selection.

Ceramic cove base represents a neat, hygienic method for treating transitions at inside corners by providing a curved surface that prevents the collection of dirt and is easy to clean. However, the limited availability of ceramic trim pieces has resulted in the use of sealant and caulk to treat such transitions.

These joints must be continually maintained throughout the life of the installation. This may include replacing the joints, which requires cutting the sealant out and possibly compromising the waterproofing membrane.

Finishing and edge protection Maintenance-free inside corners

Schluter ® -Systems offers various finishing and edge-protection profiles for outside corners and other tiled edges that can be used with any field tile, thus reducing dependence on ceramic trim and increasing design options.

These profiles are available in a wide range of materials and finishes such as stainless steel, anodized aluminum, brass, and colored PVC to produce a variety of looks, including bold contrasts, discreet color matches to the grout, and complements to plumbing fixtures.

Schluter ® -RONDEC

Provides a symmetrically rounded edge for a smooth design.

Schluter ® -QUADEC

Provides a square edge for a contemporary and sleek design.

Schluter ® -Systems offers various cove-shaped profiles to address the need to finish inside corners. These profiles can be used with any field tile to produce permanent, easy to clean, and maintenance-free floor/wall transitions and inside wall corners.

Schluter ® -DILEX-AHK

Allows for easy cleaning and will not trap debris. Anodized and Tuscan color-coated aluminum finishes.

= H r = 10 mm -

3/8"

= H

Schluter ® -DILEX-HKU

Allows for easy cleaning, will not trap debris.

Stainless steel finish.

8 mm - 5/16" r = 10 mm -

3/8"

19.5 mm - 3/4"

TILE

TILE TILE

TILE

Schluter ® -DILEX-PHK

Allows for easy cleaning and will not trap debris. PVC profile.

Schluter ® -DILEX-EKE

Provides a straight and discreet joint that eliminates sealant at inside corners.

= O

= H r = 10 mm -

3/8"

= H

5 mm - 3/16"

= U

TILE TILE

Please refer to our Illustrated Price List for details on the complete line of Schulter profiles and accessories available.

PROFILES — Details make the difference 35

THIN-SET FACTS

Discussion on thin-set mortars and Schluter

-KERDI installations

QUESTION: Should a latex-modified thin-set mortar or an unmodified thin-set mortar be used to install Schluter

-KERDI?

ANSWER:

The type of bonding mortar used to apply KERDI must be suitable for the substrate and mechanically anchor the fleece on the KERDI. For all the substrates listed in this Handbook (e.g., gypsum board, cement backerboard, etc.), an unmodified thin-set mortar is recommended. When installing KERDI with unmodified thin-set mortar over particularly dry and porous substrates, it is recommended to wet the substrate first, in order to help prevent premature drying or skinning of the thin-set mortar.

Unmodified thin-set mortar must be used to construct all KERDI seams to ensure watertight performance of the system. Learn more below.

QUESTION: Can ceramic tile, including porcelain tile, be set on Schluter

-KERDI with unmodified thin-set mortar?

ANSWER: YES. In fact, we recommend it. Here’s why:

Portland cement-based unmodified thin-set mortars are dependent on the presence of moisture for hydration in order to gain strength.

Since KERDI is impervious, it does not deprive the mortar of its moisture. This allows the cement to properly hydrate, resulting in a strong, dense bond coat. In fact, after the mortar has reached final set (usually within 24 hours), unmodified thin-set mortars achieve higher strengths when cured in continually moist conditions.

QUESTION: Can ceramic tile, including porcelain tile, be set on Schluter

-KERDI with latexmodified thin-set mortar?

ANSWER: We DON’T recommend it. Here’s why:

Latex-modified mortars must air dry for the polymers to coalesce and form a hard film in order to gain strength. When sandwiched between two impervious materials such as KERDI and ceramic tile, including porcelain tile, drying takes place very slowly through the open joints in the tile covering. [According to the Tile Council of North America's Handbook for Ceramic, Glass, and Stone Tile Installation, this drying period can fluctuate from 14 days to over 60 days, depending on the geographic location, the climatic conditions, and whether the installation is interior or exterior]. Therefore, extended cure times would be required before grouting if using modified thin-set mortars between KERDI and ceramic tile, including porcelain tile. If extended cure times were not observed, the results could be unpredictable.

This is even more important to consider in wet areas such as showers, as there is the additional concern of latex leaching.

QUESTION: How do I know if the thin-set mortar is modified or unmodified?

ANSWER:

In general, unmodified thin-set mortar is a blend of Portland cement, sand, and water retention agents that is mixed with water by the user.

The applicable product standard for unmodified thin-set mortars is ANSI A118.1. Look for this standard on the packaging (e.g., product meets ANSI A118.1 when mixed with water). Unmodified thin-set mortar may also be referred to as dry-set mortar by the manufacturer.

Modified thin-set mortars are similar to unmodified thin-set mortars, but include additional polymers such as latex. The additional polymers are introduced in either liquid or powder form. In the first case, the user mixes an unmodified or dry-set mortar powder with a liquid polymer additive instead of water. In the second case, the polymers are added by the manufacturer to the dry blend in powder form. The user then mixes the powder with water. The applicable product standards for modified thin-set mortars include ANSI A118.4 and ANSI A118.11.

ADDITIONAL NOTES

• 25 years of field experience and testing by the Tile Council of North America (TCNA) support the efficacy of using unmodified thin-set mortars in conjunction with KERDI in tiled showers.

• Remember, all thin-set mortars have an acceptable temperature range that must be observed during application and curing.

• Pre-mixed thin-set mortars and mastics are not suitable for use in conjunction with the Schluter ® -Shower System.

36 THIN-SET FACTS — Discussion on thin-set mortars and Schluter

-KERDI installations

TESTING, LISTINGS, & APPROVALS

Products and system evaluation

Schluter ® -Systems is committed to providing reliable installation systems for tile and stone. As part of this commitment, we have invested considerable resources in testing our products and obtaining listings and approvals through various certification organizations to provide our customers and local code officials with relevant data that supports the efficacy of our system.

TEST DATA

KERDI, KERDI-DS, DITRA, and DITRA-XL have been independently tested and found to meet or exceed the requirements of the American

National Standard Specifications for Load Bearing, Bonded, Waterproof Membranes for Thin-set Ceramic Tile and Dimension Stone

Installation A118.10. Data for KERDI and KERDI-DS are presented in the table below.

Property

Fungus and micro-organism resistance

Seam strength

Breaking strength

Dimensional stability

Waterproofness

7-day shear strength

7-day water immersion shear strength

4-week shear strength

12-week shear strength

100-day water immersion shear strength

Requirement

The membrane shall not support mold growth

16 lb/2 in width

170 psi

0.7% maximum length change

No moisture penetration

50 psi

KERDI

Pass

36 lb/2 in width

Performance

KERDI-DS

Pass

37 lb/2 in width

1084 psi

Pass

87 psi

77 psi

96 psi

90 psi

120 psi

1275 psi

Pass

87 psi

99 psi

93 psi

87 psi

116 psi

KERDI, KERDI-DS, and KERDI-BOARD have also been independently tested to determine the water vapor permeance of the products.

Please see further discussion on the importance of water vapor permeance on page 39.

Product

KERDI

KERDI-DS

KERDI-BOARD 1/2" (12.5 mm)

* Using the desiccant method at 100°F (38°C) and 90% RH

Test method

ASTM E96*

Performance

0.90 perms

0.19 perms

0.36 perms

KERDI, KERDI-FIX and DITRA/DITRA-XL have been independently tested to determine VOC emissions per California Specification 01350:

“Standard Practice for the Testing of Volatile Organic Emissions from Various Sources Using Small-Scale Environmental Chambers” and have been found to emit zero VOCs. Therefore, these products can contribute towards achieving the following green building credits:

• LEED, IEQ Credit 4.3: Low-Emitting Materials - Flooring Systems

• ICC 700-2008, 901.6: Pollutant Source Control - Hard-Surface Flooring

• CHPS, EQ2.2: Low-Emitting Materials

PRODUCT EVALUATIONS AND LISTINGS

Schluter ® -Shower System (Membranes and Drains)

• ICC-ES PMG Report No. PMG-1204

Membranes (KERDI/DITRA/DITRA-XL)

• ICC-ES Report No. ESR-2467 • Listed by cUPC® to meet ANSI A118.10 • Los Angeles Research Report

Drains (KERDI-DRAIN and KERDI-LINE)*

• Listed by UPC® to meet IAPMO IGC 195

• Certified by CSA to meet CSA B79

• Certified by NSF as special engineered product to meet applicable requirements of ASME A112.6.3

• Los Angeles Research Report

*KERDI-DRAIN and KERDI-LINE are available in various configurations. Please refer to pages 41 to 43 for information regarding which configurations are listed and certified.

APPROVALS

Schluter ® -Shower System

• Massachusetts • Michigan • Kentucky

Copies of the aforementioned test reports, listings, and approvals are available upon request. Listings and approvals may also be accessed via our website at www.schluter.com.

TESTING, LISTINGS, & APPROVALS — Products and system evaluation 37

MOLD

The importance of mold control

The term “mold” is used to describe visible fungal growth. Mildew is another common term which refers to the type of fungi found growing on window sills and in bathrooms. Fungi are everywhere in our environment and are found both indoors and outdoors. However, the type and amount found in the home can be an important health issue. Understanding how to effectively control mold growth is very important.

What is Mold?

Fungi are different from plants and animals. Fungi cannot produce their own nutrients as plants do and reproduce differently than both plants and animals. Molds reproduce by making spores which travel through the air to deposit on surfaces. If the conditions are right for reproduction they can grow and continue to multiply. The filamentous parts of mold attach to nutrients and form networks called mycelia. It is these networks that are visible to us in the indoor environment. Molds come in a variety of colors, but we commonly see them as green or black.

Over 1000 different species of mold have been identified in homes, but they are not all toxic to humans. Molds growing inside a home may release chemicals and spores and some may even produce mycotoxins. The chemicals released by fungi are called volatile organic compounds (VOC). For example, ethanol is a common VOC that is responsible for the distinctive musty or earthy odor associated with mold.

Health Effects

Mold can cause damage to building materials and may have adverse health effects on some individuals. The susceptibility of people to develop symptoms depends on the nature of the fungal material, genetic predisposition, age, state of health, and extent of exposure. Although there is insufficient evidence in the scientific community to determine with certainty the association between mold exposure and the effect on human health, it is of course recommended to control mold exposure in the home and workplace. Common health effects associated with exposure to mold are a variety of upper and lower respiratory tract symptoms: cough; nose, throat and eye irritation; rhinitis; sneezing; and wheezing.

These symptoms are similar to allergies and associated with asthma. Mycotoxins are fungal metabolites that have a toxic effect on humans.

Toxic effects are associated with symptoms such as fever, nausea, headaches, and skin irritations.

Factors for Mold Growth

Fungi need a source of moisture, organic material to serve as a source of nutrients, and a warm environment with a temperature range from

50 to 107 °F (10 to 42 °C) to grow. For most species of fungi, a neutral to acidic pH is preferred, with a high pH level indicating an alkaline environment that is generally not conducive to mold growth. Mold will reproduce in such conditions as long as moisture is present. Once the area is dry, the mold may stop reproducing but can continue to be allergenic to susceptible people. If moisture is reintroduced, the mold will again start the reproduction cycle and grow.

Controlling Mold Growth

As stated above, four conditions must be satisfied to support mold growth.

1. Mold spores

2. Food source (organic material)

3. Warm temperatures: 50 to 107 °F (10 to 42 °C)

4. Moisture

Mold spores travel through the air indoors and outdoors and are impossible to eliminate. The use of organic materials in construction is common in today’s building environment. Examples include wood framing members (e.g., studs, joists, I-joists, and trusses), plywood or OSB subfloors, paper-faced gypsum boards on walls and ceilings, etc. Room temperature falls within the temperature range suitable for mold growth.

Therefore, the control of moisture, including liquid water and water vapor, is the only viable method for controlling mold growth in the indoor environment.

Showers are critical areas with respect to mold and moisture control. They are commonly exposed to thousands of gallons of water per year and high humidity levels. The tile covering alone will not prevent water and moisture penetration. As such, it is essential that an effective moisture management system be designed and installed properly to protect surrounding building materials and prevent mold growth.

The traditional method for installing tiled shower assemblies creates a water in/ water out system. Since shower pan liners are placed below the mortar setting bed in these assemblies, moisture is allowed to saturate the mortar bed before exiting the system through the weep holes in the drain. When the pan liner is placed on a level substrate instead of a sloped surface, a relatively common error, moisture in the system will have no means to exit through the weep holes in the drain and the mortar bed will remain saturated for extended periods of time. The continued presence of moisture, combined with organic materials carried into the mortar bed by the rinse water, warm temperatures, and reduced pH as soluble salts are washed out of the mortar bed, increases the risk of mold growth within the system.

The Schluter ® -Shower System is an integrated family of products that creates a sealed system. KERDI is a bonded waterproof membrane that is installed on top of the mortar bed and solid backing on walls. Tile is installed directly over the membrane using thin-set mortar. The

KERDI-DRAIN was designed specifically to ensure a simple and secure connection to bonded waterproof membranes, such as KERDI, at the top of the assembly rather than below it. The resulting assembly does not permit moisture penetration into the solid backing or mortar bed, thus limiting the amount of water behind the tile covering and allowing the shower to dry out between uses. Furthermore, KERDI is a vapor retarder that protects wall cavities from water vapor penetration. Thus, the Schluter ® -Shower System provides superior moisture management and reduces the potential for mold growth within the system.

Regardless of the system used to waterproof a tiled shower, it is important to provide adequate ventilation (e.g., exhaust fans) in the bathroom to effectively manage water vapor and reduce condensation on all bathroom surfaces.

Further discussion and recommendations for mold remediation can be found in various sources, including the following.

• “A Brief Guide to Mold, Moisture, and Your Home” – U.S. Environmental Protection Agency (EPA)

• “Mold Remediation in Schools and Commercial Buildings” – U.S. Environmental Protection Agency (EPA)

• “Mould Guidelines for the Canadian Construction Industry” – Canadian Construction Association

38 MOLD — The importance of mold control

VAPOR

The importance of water vapor management

Why is water vapor management important?

It is important to consider that water exists as both liquid and vapor in showers, and must be managed in both forms. The prime example of this is the steam shower. Steam showers that are not designed to manage water vapor have caused mold growth in wall cavities, rot in wood framing, and damage to moisture-sensitive wall coverings on the opposite side of the stud cavities.

Do all waterproofing membranes manage water vapor?

The ANSI A118.10 standard for bonded waterproof membranes was developed to provide a framework for determining the suitability of these products to serve as barriers to liquid water only. As such, the standard does not include a minimum criterion to establish the ability of products to limit vapor transmission. Thus, simply selecting a membrane that meets the requirements of the ANSI A118.10 standard for a steam shower application is not enough. The ability of the product to limit vapor transmission must be considered as well.

How can I identify a waterproofing membrane that manages water vapor?

Water vapor permeance is a measure of how quickly water vapor is transmitted through a material and can be determined according to the

ASTM E96 Standard Test Method for Water Vapor Transmission of Materials. The higher the vapor permeance, the less effective a material is at slowing vapor transmission.

There is no universal requirement for vapor permeance of membranes in the building industry. The environmental conditions (i.e., differences in temperature and relative humidity), building materials, etc., and relevant field experience will determine the appropriate membrane performance for a given application. The consensus within the tile industry in North America has been that a vapor permeance of 1.0 perm or less will manage vapor effectively in showers and intermittent use steam shower applications.

The TCNA Handbook for Ceramic, Glass, and Stone Tile Installation and the TTMAC Specification Guide 09 30 00 Tile Installation Manual specify a water vapor permeance of 0.5 perms or less for bonded waterproofing membranes used in continuous use steam rooms

(e.g., those found in health clubs, spas, etc.) when tested using the desiccant method at 100°F (38°C) and 90% RH.

Does the Schluter

-Shower System manage water vapor?

Schluter ® -Systems has tested the various options within the Schluter ® -Shower System for moisture management, including KERDI,

KERDI-DS, and KERDI-BOARD in the more aggressive conditions referenced above. The table below summarizes Schluter ® -Systems' recommendations for the use of these products and respective water vapor permeance values.

Product

KERDI

KERDI-DS

KERDI-BOARD

Recommended Applications

Showers, intermittent use steam showers, and bathtub surrounds

Continuous use steam rooms

Showers, intermittent use steam showers, and bathtub surrounds

1 Tested according to ASTM E96, using the desiccant method at 100°F (38°C) and 90% RH

2 Previously reported a value of 0.75 perms when tested according to ASTM E96, using the water method at 73.4°F (23°C) and 50% RH

3 1/2" – 12.5 mm-thick KERDI-BOARD tested

Water Vapor Permeance (perms) 1

0.90

0.19

0.36

While the water vapor permeance of KERDI-BOARD meets the water vapor permeance recommendations for continuous use steam rooms in tile industry standard guidelines, Schluter ® -Systems has chosen to require the KERDI-DS membrane for these demanding applications in an effort to be conservative and provide the best possible solution for our customers.

Thus, the Schluter ® -Shower System has solutions that provide superior moisture management for virtually any tile application.

VAPOR — The importance of water vapor management 39

PRODUCT & ORDERING INFO

Ordering information for the Schluter

-Shower System and DITRA components outlined in this Handbook is located below.

For technical support, our Illustrated Price List, or additional information on our complete product line, please call 1-800-472-4588 (USA) or 1-800-667-8746 (Canada), or visit our comprehensive website at www.schluter.com.

Waterproofing strip

Inside corner (FI)

Left corner (L)

KERDI-SEAL-PS

Outside corner (FA)

Right corner (R)

KERDI-SEAL-MV

KERDI-FIX

* Color codes: BW - Bright white, G - Grey

Note: 1 mil = 1 one-thousandth of an inch.

KERDI is listed by cUPC

® and evaluated by ICC-ES

(Report Nos. ESR-2467 and PMG-1204).

40 PRODUCT & ORDERING INFO

Schluter ®

-KERDI

KERDI is a pliable sheet-applied polyethylene waterproofing membrane and vapor retarder that guarantees uniform thickness. It is covered on both sides with a fleece webbing to anchor the membrane in thin-set mortar.

KERDI waterproofing membrane

Item No.

Dimensions

KERDI 200/5M

KERDI 200/10M

KERDI 200/20M

KERDI 200

3' 3" x 16' 5" = 54 ft 2 (1 m x 5 m = 5 m 2 )

3' 3" x 33' = 108 ft 2 (1 m x 10 m = 10 m 2 )

3' 3" x 65' 7" = 215 ft 2 (1 m x 20 m = 20 m 2 )

3' 3" x 98' 5" = 323 ft 2 (1 m x 30 m = 30 m 2 )

KERDI-DS waterproofing membrane

KERDI-DS 3' 3" x 98' 5" = 323 ft 2 (1 m x 30 m = 30 m 2 )

KERDI-BAND waterproofing strip

KEBA 100/125/5M

KEBA 100/125/10M

KEBA 100/185/5M

KEBA 100/250/5M

KEBA 100/125

KEBA 100/185

KEBA 100/250

5" x 16' 5" (125 mm x 5 m)

5" x 33' (125 mm x 10 m)

7-1/4" x 16' 5" (185 mm x 5 m)

10" x 16' 5" (250 mm x 5 m)

5" x 98' 5" (125 mm x 30 m)

7-1/4" x 98' 5" (185 mm x 30 m)

10" x 98' 5" (250 mm x 30 m)

KERDI-KERECK-F waterproofing corners

Item No.

KERECK/FI 2

KERECK/FI 10

Type/Quantity

Inside corner / 2 units

KERECK/FA 2

KERECK/FA 10

Inside corner / 10 units

Outside corner / 2 units

Outside corners / 10 units

KERDI-KERECK-F 135º inside and bench corners

Item No.

KERSB135K

KERECK135FI2

Packaging

Bench/neo-angle package

1 left and 1 right bench corner, 2 135º inside corners

135º inside corners / 2 units

KERECK135FI10

KERSB135KLR

135º inside corners / 10 units

1 left and 1 right bench corner

KERSB135K5LR 5 left and 5 right bench corner

KERDI-KERS waterproofing corners

Item No.

KERS20L

KERS28L

KERS20R

KERS28R

Type/Size

Left: 3/4" (20 mm)

Left: 1-1/8" (28 mm)

Right: 3/4" (20 mm)

Right: 1-1/8" (28 mm)

KERDI-SEAL-PS pipe seal with gasket

Item No.

KMS185/12

KMS185/20

KMS10185/12

KMS10185/20

Opening diameter/Quantity

1/2" (12.5 mm) / 1 unit

3/4" (20 mm) / 1 unit

1/2" (12.5 mm) / 10 units

3/4" (20 mm) / 10 units

KERDI-KM pipe seal

KM5117/22 7/8" (22 mm) / 5 units

KERDI-SEAL-MV mixing valve seal with gasket

KMSMV235/114 4-1/2" (114 mm) / 1 unit

4-1/2" (114 mm) / 10 units KMSMV10235/114

KERDI-FIX adhesive/sealant

Item No.

KERDIFIX/ color*

Volume

290 ml

Thickness

8 mil

20 mil

4 mil

Thickness

4 mil

Thickness

4 mil

Thickness

4 mil

Thickness

4 mil

Schluter ®

-KERDI-DRAIN

KERDI-DRAIN is a floor drain designed with a sloped, integrated bonding flange to provide a secure connection to KERDI and other bonded waterproof membranes at the top of the assembly.

Unique Features and Benefits:

- Appropriate for both mortar bed and KERDI-SHOWER-ST tray installations.

- Features a fully adjustable square grate and accommodates a wide range of tile thicknesses 1/4" to 1-1/4" (6 mm to 31 mm). Grate is available in stainless steel (E), stainless steel with oil-rubbed bronze finish (EOB), brushed brass anodized aluminum

(AMGB), brushed copper/bronze anodized aluminum (AKGB), and brushed nickel anodized aluminum (ATGB).

- Ideal for new construction and renovation work.

- Saves installation time and labor, as it eliminates the prep work required for a traditional two-step mortar pan.

- Integrated bonding flange ensures secure connection to KERDI at top of the assembly.

Anodized Aluminum Stainless Steel

6" Grate Options

Stainless Steel

4" Grate Options

Tileable

Tileable (ECS)

Patent pending

Brushed nickel

(ATGB)

Brushed copper/ bronze

(AKGB)

Brushed brass

(AMGB)

Oil-rubbed bronze

(EOB)

Stainless steel (E)

(6E) (6RE)

KERDI-DRAIN - Components - ABS, PVC or stainless steel flange

ABS or PVC flange Stainless steel flange Includes

1 KERDI-DRAIN

Description

Drain with integrated bonding flange in ABS,

PVC or stainless steel, and grate assembly

Quantity

KERDI-KERECK-F Pre-formed waterproofing corners

KERDI-SEAL-PS

KERDI-SEAL-MV

5 KERDI-FIX

Pipe seal (3/4")

Mixing valve seal

Sealing and bonding compound (66 ml)

(Included with stainless steel flange only)

4 inside

2 outside

2" (50 mm) drain outlet

ABS flange PVC flange

Stainless steel flange

4" (100 mm) Square Grate

Stainless steel (E) KD2/ABS/E 1 KD2/PVC/E 1 KD2/E/E 1

Oil-rubbed bronze stainless steel (EOB)

Brushed brass anod. alu. (AMGB)

Brushed copper/ bronze anod. alu. (AKGB)

Brushed nickel anod. alu. (ATGB)

Tileable (ECS)

KD2/ABS/EOB

KD2/ABS/AMGB

KD2/ABS/AKGB

KD2/ABS/ATGB

KD2/PVC/EOB

KD2/PVC/AMGB

KD2/PVC/AKGB

KD2/PVC/ATGB

KD2/E/EOB

KD2/E/AMGB

KD2/E/AKGB

KD2/E/ATGB

KD2/ABS/ECS 1 KD2/PVC/ECS 1 KD2/E/ECS 1

6" (150 mm) Square or Round Grate

Square Grate stainless steel (E)

Round Grate stainless steel (E)

KD2/ABS/6E

KD2/ABS/6RE

KD2/PVC/6E

KD2/PVC/6RE

1 Listed by ICC-ES (Report No. PMG-1204), UPC

® , CSA, and NSF.

KD2/E/6E 1

KD2/E/6RE 1

3" (75 mm) drain outlet

ABS flange PVC flange

6" (150 mm) Square or Round Grate

Square Grate stainless steel (E) KD3/ABS/6E

Round Grate stainless steel (E) KD3/ABS/6RE

KD3/PVC/6E

KD3/PVC/6RE

Stainless steel flange

KD3/E/6E 1

KD3/E/6RE 1

Also available:

Stainless steel flange with

2" (50 mm) threaded outlet.

Listed by ICC-ES (Report No. PMG-1204), UPC

® , CSA, and NSF.

PRODUCT & ORDERING INFO 41

Schluter ®

-KERDI-DRAIN - Adaptor Kits

KERDI-DRAIN ADAPTOR KITS are used to convert traditional clamping ring drains to integrated bonding flange drains when removal of the clamping ring drain is not practical.

Residential Commercial

Schluter ® -KERDI-DRAIN with residential adaptor ring and ABS flange

Includes

1 KERDI-DRAIN

Description

Drain, with integrated bonding flange and grate assembly

2 Adaptor ring ** For residential clamping ring drains

2 3 KERDI-KERECK-F Preformed waterproofing corners

3 4 5

KERDI-SEAL-PS

KERDI-SEAL-MV

KERDI-FIX

Pipe seal (3/4")

Mixing valve seal

Sealing and bonding compound (66 ml)

** D Schluter ® -Systems L.P., U.S. patent No. D593,641, other patents pending.

Quantity

4 inside and

2 outside

Schluter ® -KERDI-DRAIN with commercial adaptor ring and ABS flange

1 1

Includes

1 KERDI-DRAIN

Description

Drain, with integrated bonding flange in ABS or stainless steel, and grate assembly

2 Adaptor ring ** For commercial clamping ring drains

2 3

KERDI-FIX Sealing and bonding compound (66 ml)

** D Schluter ® -Systems L.P., U.S. patent No. D593,641, other patents pending.

Quantity

Residential

4" (100 mm) Square Grate

Stainless steel

(E)

Oil-rubbed bronze stainless steel (EOB)

Brushed brass anod. alu. (AMGB)

Brushed copper/ bronze anod. alu. (AKGB)

Brushed nickel anod. alu. (ATGB)

Adaptor kit with standard

ABS bonding flange

KDAR/ABS/E

KDAR/ABS/EOB

KDAR/ABS/AMGB

KDAR/ABS/AKGB

KDAR/ABS/ATGB

C ommercial

Standard ABS bonding flange

Extended ABS bonding flange

4" (100 mm) Square Grate

Stainless steel

(E)

Oil-rubbed bronze stainless steel (EOB)

Brushed brass anod. alu. (AMGB)

Brushed copper/ bronze anod. alu. (AKGB)

Brushed nickel anod. alu. (ATGB)

KDA/ABS/E

KDA/ABS/EOB

KDA/ABSL/E

KDA/ABSL/EOB

KDA/ABS/AMGB KDA/ABSL/AMGB

KDA/ABS/AKGB KDA/ABSL/AKGB

KDA/ABS/ATGB KDA/ABSL/ATGB

Tileable grate (ECS) KDA/ABS/ECS KDA/ABSL/ECS

6" (150 mm) Square or Round Grate

Square Grate stainless steel (E)

Round Grate stainless steel (E)

KDA/ABS/6E

KDA/ABS/6RE

KDA/ABSL/6E

KDA/ABSL/6RE

Stainless steel bonding flange

KDA/E/E

KDA/E/EOB

KDA/E/AMGB

KDA/E/AKGB

KDA/E/ATGB

KDA/E/ECS

KDA/E/6E

KDA/E/6RE

42 PRODUCT & ORDERING INFO

Schluter ®

-KERDI-LINE

KERDI-LINE is a low profile linear floor drain specifically designed for bonded waterproofing assemblies. KERDI-LINE can be installed adjacent to walls or at intermediate locations in showers, wet rooms, and other applications that require waterproofing and drainage. The floor can be sloped on a single plane to KERDI-LINE, which enables the use of large-format tiles and creates interesting design opportunities.

KERDI-LINE consists of a formed stainless steel channel body and a grate assembly that can be seamlessly adjusted to the thickness of the ceramic tile or stone covering from 1/8" to 1" (3 mm to 25 mm). Grate assemblies are available in three designs: closed, perforated, or tileable covering support.

Note: There are multiple selections to be made for this product. Start by selecting the appropriate flange length then proceed to grate selection accordingly, keeping in mind there are two frame heights with two grate options (A or B), and a frameless option (D).

= L

Channel body with center outlet

Wall placement

8" - 20.3 cm

7/8" -

22 mm

2-1/4" -

57 mm

7/8" -

22 mm

4-23/32" - 120 mm

7/8" -

22 mm

2-1/4" -

57 mm

7/8" -

22 mm

Intermediate placement

5-15/32" - 137 mm

= L

Channel body with off-set outlet

3/8" -

10 mm

1-27/32" -

47 mm

3/8" -

10 mm

2-1/8" - 54 mm

2" - 50 mm

= H = H

Closed (A)

2-29/32" - 74 mm

Perforated (B)

2-29/32" - 74 mm

Frameless Tileable (D) Patent pending

KERDI-LINE linear floor drain

Bonding flange

52 - 130 54 - 135 KLV 60 E 130

56 - 140 58 - 145 KLV 60 E 140

60 - 150 62 - 155 KLV 60 E 150

64 - 160 66 - 165 KLV 60 E 160

68 - 170 70 - 175 KLV 60 E 170

72 - 180 74 - 185 KLV 60 E 180

Grate A

L = in. - cm

= in. - cm

Center outlet Off-set outlet

Frame =

3/4" - 19 mm

Frame =

1-1/8" - 30 mm

20 - 50 22 - 55 KLV 60 E 50

24 - 60 26 - 65 KLV 60 E 60

KLAR 19 EB 50

KLAR 19 EB 60

KLAR 30 EB 50

KLAR 30 EB 60

28 - 70 30 - 75 KLV 60 E 70 KLVO 60 E 70 KLAR 19 EB 70 KLAR 30 EB 70

Frame =

3/4" - 19 mm

Frame =

1-1/8" - 30 mm

For use with bonding flange with center outlet

KLB 19 EB 50 KLB 30 EB 50 KLDRE 50

KLB 19 EB 60 KLB 30 EB 60 KLDRE 60

For use with bonding flange with off-set outlet

KLB 19 EB 70 KLB 30 EB 70 KLDRE 70 KLDRO E 70

32 - 80 34 - 85 KLV 60 E 80 KLVO 60 E 80 KLAR 19 EB 80 KLAR 30 EB 80

36 - 90 38 - 95 KLV 60 E 90 KLVO 60 E 90 KLAR 19 EB 90 KLAR 30 EB 90

KLB 19 EB 80 KLB 30 EB 80 KLDRE 80 KLDRO E 80

KLB 19 EB 90 KLB 30 EB 90 KLDRE 90 KLDRO E 90

40 - 100 42 - 105 KLV 60 E 100 KLVO 60 E 100 KLAR 19 EB 100 KLAR 30 EB 100 KLB 19 EB 100 KLB 30 EB 100 KLDRE 100 KLDRO E 100

44 - 110 46 - 115 KLV 60 E 110 KLVO 60 E 110 KLAR 19 EB 110 KLAR 30 EB 110 KLB 19 EB 110 KLB 30 EB 110 KLDRE 110 KLDRO E 110

48 - 120 50 - 125 KLV 60 E 120 KLVO 60 E 120 KLAR 19 EB 120 KLAR 30 EB 120 KLB 19 EB 120 KLB 30 EB 120 KLDRE 120 KLDRO E 120

KLAR 19 EB 130

KLAR 19 EB 140

KLAR 19 EB 150

KLAR 19 EB 160

KLAR 19 EB 170

KLAR 19 EB 180

Grate B

KLB 19 EB 130

KLB 19 EB 140

KLB 19 EB 150

KLB 19 EB 160

KLB 19 EB 170

KLB 19 EB 180

Grate D

KLDRE 130

KLDRE 140

KLDRE 150

KLDRE 160

KLDRE 170

KLDRE 180

KERDI-LINE is listed by ICC-ES (Report No. PMG-1204), UPC

® , CSA, and NSF.

Note: Purchase bonding flange and grate assembly separately.

PRODUCT & ORDERING INFO 43

Curb

KERDI-SHOWER-ST shower tray

KERDI-SHOWER-L/-LS shower trays

Ramp

Benches

Schluter ®

-KERDI-SHOWER

KERDI-SHOWER prefabricated substrates are made of expanded polystyrene foam, for use in conjunction with the KERDI waterproofing membrane. Prefabricated substrates provide an alternative to shower bases constructed of mortar and other shower elements constructed of framing and solid backing.

KERDI-SHOWER-ST shower tray for use with KERDI-DRAIN

ST-122

Item No.

ST-183

Dimensions

48" x 48" (122 cm x 122 cm)

72" x 72" (183 cm x 183 cm

ST-81/152 32" x 60" (81 cm x 152 cm)

ST-81/152 BR 32" x 60" (81 cm x 152 cm)

KERDI-SHOWER-L/-LS shower tray for use with KERDI-LINE

KSL 1000 S

KSL 1400 S

KSL 1000

KSL 1400

39" x 39" (100 cm x 100 cm)

55" x 55" (140 cm x 140 cm)

39" x 39" (100 cm x 100 cm)

55" x 55" (140 cm x 140 cm)

KERDI-SHOWER-SB shower bench

Item No.

Dimensions 1

SB41

SB2981

SB29107

SB29122

SB4181

SB41122

16" x 16" (41 cm x 41 cm)

32" x 11-1/2" (81 cm x 29 cm)

42" x 11-1/2" (107 cm x 29 cm)

48" x 11-1/2" (122 cm x 29 cm)

32" x 16" (81 cm x 41 cm)

48" x 16" (122 cm x 41 cm)

KERDI-SHOWER-SC shower curb

Item No.

SR122

Dimensions

48" x 15-7/8" (122 cm x 40 cm)

Drain Placement

Center

Off-center

Shape

Triangular

Rectangular

Item No.

SC122

Dimensions

48" x 6" x 4-1/2" (122 cm x 15 cm x 11.5 cm)

KERDI-SHOWER-SR shower ramp

Wall

Center

1 Height = 20" (51 cm)

Schluter ®

-KERDI-BOARD-SN

KERDI-BOARD-SN prefabricated shower niche

Item No.

KB 12 SN 305 152 A

12" (305 mm) 6" (152 mm)

16" (406 mm) 10" (250 mm)

KB 12 SN 305 305 A 12" (305 mm) 12" (305 mm) 16" (406 mm) 16" (406 mm)

KB 12 SN 305 508 A1 12" (305 mm) 20" (508 mm) 16" (406 mm) 24" (610 mm)

KB 12 SN 305 711 A1 12" (305 mm) 28" (711 mm) 16" (406 mm) 32" (810 mm)

Depth Shelf

3-1/2"

(8.9 cm)

3-1/2"

(8.9 cm)

3-1/2"

(8.9 cm)

3-1/2"

(8.9 cm)

SHOWERPROFILE-S

SHOWERPROFILE-R

= H

H = 3/16" (5 mm)

3/8" (10 mm)

3/8"

(10 mm)

H = 1/2"

(12.5 mm)

= L

25/32" (20 mm)

= H

7/8" (22mm) /

1-1/4" (32 mm)

H = variable

35 mm - 1-3/8''

KERDI-LINE-FC

44 PRODUCT & ORDERING INFO

= H

Schluter ® -Systems

Shower Profiles

SHOWERPROFILE-S tapered edging profile

Item No.

SPSA 50 EB/120

SPSA 50 EB/160

SPSA 50 EB/200

SPSB 100 EB/120

SPSB 100 EB/160

SPSB 100 EB/200

SPSB 125 EB/120

SPSB 125 EB/160

3/16" (5 mm)

1/4" (6 mm)

Length

1-3/16" (30 mm) 47-1/4" (1.2 m)

1-1/2" (38 mm) 63" (1.6 m)

1-13/16" (46 mm) 78-3/4" (2 m)

3/8" (10 mm)

3/8" (10 mm) 1-11/32" (34 mm) 47-1/4" (1.2 m)

3/8" (10 mm) 1-1/2" (38 mm) 63" (1.6 m)

3/8" (10 mm) 3/8" (10 mm) 2" (50 mm) 78-3/4" (2 m)

1/2" (12.5 mm) 3/8" (10 mm) 1-11/32" (34 mm) 47-1/4" (1.2 m)

1/2" (12.5 mm) 3/8" (10 mm) 1-1/2" (38 mm) 63" (1.6 m)

SPSB 125 EB/200 1/2" (12.5 mm) 3/8" (10 mm) 2" (50 mm)

SHOWERPROFILE-R edging profile

78-3/4" (2 m)

Item No.

SPRA 23 EB/100

Height

29/32" - 1-3/8" (23 mm - 35 mm)

Length

39" (1 m)

SPRA 23 EB/140

SPRA 33 EB/100

SPRA 33 EB/140

29/32" - 1-3/8" (23 mm - 35 mm)

1-5/16" - 1-25/32" (33 mm - 45 mm)

KERDI-LINE-FC cover plate

Item No.

V / KLEB 35

Width

1-3/8" (35 mm)

55" (1.4 m)

39" (1 m)

55" (1.4 m)

48" - 122 cm

Schluter ®

-KERDI-SHOWER-KIT

The KERDI-SHOWER-KIT is an all-inclusive package containing the components required to create a watertight shower assembly without a mortar bed.

Schluter ® -KERDI-SHOWER-KIT

Includes

KERDI 10 M

KERDI 12 M

Description

KERDI-SHOWER-ST Shower Tray

KERDI-SHOWER-SC Shower Curb 48" x 6" x 4-1/2"

Waterproofing membrane 3' 3" x 33' = 108 ft

Waterproofing membrane 3' 3" x 39' 4" =

128 ft 2

Quantity

48" x 48" 72" x 72" 32" x 60"

KERDI 20 M

KERDI-BAND

Waterproofing membrane 3' 3" x 65' 7" = 215 ft 2

Waterproofing strip 5" x 33' 1

2 1

KERDI-DRAIN Drain, with integrated bonding flange with 2" (50 mm) outlet

1 1 1

KERDI-KERECK-F Preformed waterproofing corners

KERDI-SEAL-PS Pipe seal (3/4")

KERDI-SEAL-MV Mixing valve seal

4 inside and 2 outside

72" - 183 cm

48" x 48" (122 cm x 122 cm) Kit

Select material for drain (ABS or PVC) and grate finish

Item No.

KK122ABSECS

KK122ABSE

KK122ABSEOB

KK122ABSATGB

KK122ABSAKGB

KK122ABSAMGB

KK122PVCECS

KK122PVCE

KK122PVCEOB

KK122PVCATGB

KK122PVCAKGB

KK122PVCAMGB

Drain

Material

ABS

PVC

Grate finish

Tileable

Stainless steel 304 (1.4301 = V2A)

Oil-rubbed bronze stainless steel

Brushed nickel anodized aluminum

Brushed copper/bronze anod. alu.

Brushed brass anodized aluminum

Tileable

Stainless steel 304 (1.4301 = V2A)

Oil-rubbed bronze stainless steel

Brushed nickel anodized aluminum

Brushed copper/bronze anod. alu.

Brushed brass anodized aluminum

60" - 152 cm

72" x 72" (183 cm x 183 cm) Kit

Select material for drain (ABS or PVC) and grate finish

Item No.

KK183ABSECS

KK183ABSE

KK183ABSEOB

KK183ABSATGB

KK183ABSAKGB

KK183ABSAMGB

KK183PVCECS

KK183PVCE

KK183PVCEOB

KK183PVCATGB

KK183PVCAKGB

KK183PVCAMGB

Drain

Material

ABS

PVC

Grate finish

Tileable

Stainless steel 304 (1.4301 = V2A)

Oil-rubbed bronze stainless steel

Brushed nickel anodized aluminum

Brushed copper/bronze anod. alu.

Brushed brass anodized aluminum

Tileable

Stainless steel 304 (1.4301 = V2A)

Oil-rubbed bronze stainless steel

Brushed nickel anodized aluminum

Brushed copper/bronze anod. alu.

Brushed brass anodized aluminum

60" - 152 cm

32" x 60" (81 cm x 152 cm) Kit

Select material for drain (ABS or PVC) and grate finish

Item No.

KK81152ABSECS

KK81152ABSE

KK81152ABSEOB

KK81152ABSATGB

KK81152ABSAKGB

KK81152ABSAMGB

KK81152PVCECS

KK81152PVCE

KK81152PVCEOB

KK81152PVCATGB

KK81152PVCAKGB

KK81152PVCAMGB

Drain

Material

ABS

PVC

Grate finish

Tileable

Stainless steel 304 (1.4301 = V2A)

Oil-rubbed bronze stainless steel

Brushed nickel anodized aluminum

Brushed copper/bronze anod. alu.

Brushed brass anodized aluminum

Tileable

Stainless steel 304 (1.4301 = V2A)

Oil-rubbed bronze stainless steel

Brushed nickel anodized aluminum

Brushed copper/bronze anod. alu.

Brushed brass anodized aluminum

Note: Tray features off-center drain placement:

10" (25.4 cm) o.c. from end of tray.

32" x 60" (81 cm x 152 cm) Kit

Select material for drain (ABS or PVC) and grate finish

Item No.

KKB81152ABSECS

KKB81152ABSE

KKB81152ABSEOB

KKB81152ABSATGB

KKB81152ABSAKGB

KKB81152ABSAMGB

KKB81152PVCECS

KKB81152PVCE

KKB81152PVCEOB

KKB81152PVCATGB

KKB81152PVCAKGB

KKB81152PVCAMGB

Drain

Material

ABS

PVC

Grate finish

Tileable

Stainless steel 304 (1.4301 = V2A)

Oil-rubbed bronze stainless steel

Brushed nickel anodized aluminum

Brushed copper/bronze anod. alu.

Brushed brass anodized aluminum

Tileable

Stainless steel 304 (1.4301 = V2A)

Oil-rubbed bronze stainless steel

Brushed nickel anodized aluminum

Brushed copper/bronze anod. alu.

Brushed brass anodized aluminum

Note: The KERDI-SHOWER-KIT is also available without the drain. This kit contains the same components as the complete KERDI-SHOWER-KIT, except the KERDI-DRAIN which must be purchased separately. This kit allows you to select the drain that is best suited to your application (i.e. KERDI-DRAIN with 3" outlet or KERDI-DRAIN with adaptor ring).

PRODUCT & ORDERING INFO 45

Additional panels and accessories

Please refer to our Illustrated Price List for details.

Grooved panels

Profiles

L-shaped panels

Anchors

U-shaped panels

Washers, screws and adhesive tape

Schluter ®

-KERDI-BOARD

KERDI-BOARD is a multifunctional tile substrate and building panel, which can also be used for creating bonded waterproofing assemblies with tile coverings. It consists of an extruded polystyrene foam panel, with a special reinforcement material on both sides and fleece webbing for effective anchoring in thin-set mortar.

The boards are simply cut to size with a utility knife. The gridlines, which are printed on the surface, are helpful for neat and quick cuts and installation. Tiles can be installed directly over KERDI-BOARD using the thin-set method.

Schluter ® -KERDI-BOARD

Substrate and building panel

H =

Panel dimension: 32" x 48" (81 cm x 122 cm)

1/2" (12.5 mm)

Item No.

KB 12 1220 812

Panel dimension: 48" x 64" (122 cm x 162.5 cm)

3/16" (5 mm) KB 5 1220 1625

3/8" (9 mm)

1/2" (12.5 mm)

KB 9 1220 1625

KB 12 1220 1625

Panel dimension: 48" x 96" (122 cm x 244 cm)

3/16" (5 mm) KB 5 1220 2440

3/8" (9 mm)

1/2" (12.5 mm)

KB 9 1220 2440

KB 12 1220 2440

5/8" (15 mm) KB 15 1220 2440

Panel dimension: 24-1/2" x 96" (62.5 cm x 244 cm)

3/4" (19 mm) KB 19 625 2440

1" (25 mm)

1-1/2" (38 mm)

KB 25 625 2440

KB 38 625 2440

2" (50 mm) KB 50 625 2440

Panel dimension: 48" x 120" (122 cm x 305 cm)

5/8" (15 mm) KB 15 1220 3050

DITRA and DITRA-XL are listed by cUPC

and evaluated by ICC-ES (Report Nos. ESR-2467 and

PMG-1204).

Schluter ®

-DITRA

DITRA is a pressure-stable polyethylene uncoupling membrane, vacuum-formed in a cutback grid design, with an anchoring fleece laminated to its underside.

DITRA is 1/8" (3 mm) in height. DITRA-XL is 5/16" (7 mm) in height.

Schluter ® -DITRA

Item No.

Packaging

DITRA uncoupling and waterproofing membrane (1/8" - 3 mm thick)

DITRA 5M

DITRA 150

DITRA 30

3' 3" x 16' 5" = 54 ft 2 (1 m x 5 m = 5 m 2 )

3' 3" x 45' 9" = 150 ft 2 (1 m x 14 m = 14 m 2 )

3' 3" x 98' 5" = 323 ft 2 (1 m x 30 m = 30 m 2 )

DITRA-XL uncoupling and waterproofing membrane (5/16" - 7 mm thick)

DITRA-XL/175 3' 3" x 53' 3" = 175 ft 2 (1 m x 16.25 m = 16.25 m 2 )

46 PRODUCT & ORDERING INFO

Schluter ®

-DITRA-TROWEL and

Schluter ®

-KERDI-TROWEL

Used to install DITRA and KERDI membranes. The DITRA-TROWEL features an

11/64" x 11/64" (4.5 mm x 4.5 mm) square-notched design while the KERDI-TROWEL features a 1/8" x 1/8" (3 mm x 3 mm) square-notched design.

Schluter ® -DITRA-TROWEL and Schluter ® -KERDI-TROWEL

Trowels used to install Schluter ® -DITRA and Schluter ® -KERDI membranes

Item No.

Notch Size Packaging

TRL-DIT6

TRL-KER6

11/64" x 11/64" (4.5 mm x 4.5 mm)

1/8" x 1/8" (3 mm x 3 mm)

6 units

WARRANTY

Schluter

-Shower System 10-Year Limited Warranty

COVERAGE AND CONDITIONS: Subject to the conditions and limitations as stated hereinafter, Schluter ® -Systems* warrants that the

Schluter ® -Shower System (the “Products”)** will meet all composition and performance criteria for a period of ten (10) years from the date of purchase only when the Products are used and installed in accordance with the terms and conditions of the Schluter ® -Shower System Installation

Handbook and industry standard guidelines that are not in conflict with the Handbook in effect at the time of installation. Further, efflorescence is considered to be a natural occurrence with cementitious materials and is therefore not considered to be a defective condition and is not covered by this warranty. It is the responsibility of the owner/builder/installer to ensure the suitability of all building materials and all associated building materials for the owner’s intended use. It is recommended that the owner consult with an experienced and professional installer.

RESOLUTION: If the Products fail to meet this warranty, then the owner’s exclusive remedy and the sole obligation of Schluter ® -Systems, at its election, shall be to a) reinstall or replace the failed portion of the tile assembly or b) pay an amount not to exceed the original square foot cost of the installation of the tile assembly verified to be defective. Tile assembly is defined to include all Schluter ® -KERDI products, non-reusable tile surfaces, and the appropriate setting and grouting materials. Further, due to conditions beyond the control of Schluter ® -Systems (e.g., color and shade availability, discontinuation, normal wear and tear), Schluter ® -Systems cannot guarantee or warrant an exact match to the specific tile, stone, or other covering materials used in the installation. In such events, substantially similar materials may be substituted.

DISCLAIMER: THERE ARE NO WARRANTIES BEYOND THIS EXPRESSED WARRANTY AS STATED ABOVE. ALL OTHER WARRANTIES,

REPRESENTATIONS OR CONDITIONS, EXPRESSED OR IMPLIED, ARE DISCLAIMED AND EXCLUDED, INCLUDING WARRANTIES,

REPRESENTATIONS OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARISING BY STATUTE

OR OTHERWISE BY LAW OR FROM A COURSE OF DEALING OR USAGE OF TRADE. SCHLUTER ® -SYSTEMS EXCLUDES AND IN NO

EVENT SHALL HAVE ANY LIABILITY FOR LOST PROFITS OR ANY OTHER INDIRECT, SPECIAL, INCIDENTAL, PUNITIVE, EXEMPLARY, OR

CONSEQUENTIAL DAMAGES, ARISING OUT OF OR OTHERWISE CONNECTED TO FAILURE OF THE PRODUCTS, NOR MISUSE OF THE

PRODUCTS OR FAILURE TO PROPERLY MAINTAIN THE SHOWER OR BATHTUB SURROUND. REGARDLESS OF ANY STRICT LIABILITY,

ACTIVE OR PASSIVE NEGLIGENCE OF SCHLUTER ® -SYSTEMS, AND REGARDLESS OF THE LEGAL THEORY (CONTRACT OR TORT

OR EXTRA-CONTRACTUAL OR OTHER), NOR FROM ACTS OF WAR, TERRORISM, FAULTY AND NEGLIGENT PENETRATION OF THE

SYSTEM, FIRES, EXPLOSIONS, ACTS OF GOD, INTENTIONAL ACTS OF DESTRUCTION OR ANY LOSSES DUE TO STRUCTURAL FAILURE

OR OTHER CAUSES UNRELATED TO THE PRODUCTS OR DELAYS, OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES.

THIS WARRANTY IS GIVEN IN LIEU OF ANY OTHER WARRANTY EXPRESSED OR IMPLIED. THE REMEDIES CONTAINED HEREIN ARE

THE ONLY REMEDIES AVAILABLE FOR BREACH OF THIS WARRANTY. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS;

SOME STATES AND PROVINCES DO NOT ALLOW DISCLAIMERS OR OTHER RESTRICTIONS OF IMPLIED WARRANTIES, SO SOME OF

THE ABOVE DISCLAIMERS MAY NOT APPLY TO YOU.

TRANSFERABILITY: This Limited Warranty extends ONLY to the original end user (defined as original intended owner and user of the property/unit in which the installation is incorporated - herein referred to as “Owner”) and is not transferable or assignable, unless approved in writing by the Technical Director or an Officer of Schluter ® -Systems or otherwise prohibited by specific state or provincial law.

MODIFICATIONS TO WARRANTY: No changes or modification of any terms or conditions of this warranty are allowed unless authorized by written agreement and signed by the Technical Director or an Officer of Schluter ® -Systems.

EFFECTIVE DATE: This warranty shall supersede and replace any and all prior oral or written warranties, agreements, or other such representations made by or on behalf of Schluter ® -Systems relative to the Products or the application of the Products and shall apply to any installation occurring on or after January 1, 2013.

CLAIMS ON THIS LIMITED WARRANTY: To make a claim under this Limited Warranty, the Owner must provide Schluter ® -Systems with written notice within 30 days of any alleged defect in the Products covered by this Limited Warranty, together with date and proof of purchase of the Products, proof of the costs of the original installation and name and address of all installers, failing which this Limited Warranty shall be of no legal effect. Schluter ® -Systems reserves the right at its election and as a condition of this Limited Warranty to inspect the alleged failed and defective condition.

All U.S. Claims shall be sent to: All Canadian Claims shall be sent to:

Schluter Systems L.P.

Attn: Warranty Claims Dept.

Schluter Systems (Canada), Inc.

Attn: Warranty Claims Dept.

194 Pleasant Ridge Road

Plattsburgh, NY 12901-5841

21100 chemin Ste-Marie

Ste-Anne-de-Bellevue, QC H9X 3Y8

*For the purpose of this warranty Schluter Systems, L.P. shall provide the warranty for all products for end users located in the United States, and

Schluter Systems (Canada) Inc. shall provide the warranty for all products for end users located in Canada. This warranty is limited to sales of the Products made in and intended for use in the United States and Canada.

**Schluter ® -Shower System (the “Products”): The Products are defined to include all Schluter ® -KERDI products referred to in the

Handbook and used in the integrated Schluter ® -Shower System.

WARRANTY 47

Schluter Systems L.P.

•

194 Pleasant Ridge Road, Plattsburgh, NY 12901-5841

•

Tel.: 800-472-4588

•

Fax: 800-477-9783

Schluter Systems (Canada) Inc. • 21100 chemin Ste-Marie, Ste-Anne-de-Bellevue, QC H9X 3Y8 • Tel.: 800-667-8746 • Fax: 877-667-2410

www.schluter.com

Hello! I am an AI chatbot specifically trained to assist you with the Schluter KKB81152PVCEOB Kerdi-Shower 32 in. x 60 in. Off-Center Shower Kit in PVC with Oil-Rubbed Bronze Stainless Steel Drain Grate Installation guide. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant terminated

Key features

Integrated waterproofing membrane
Prefabricated shower trays
Customizable shower base options
Barrier-free shower options
Steam shower options
Steam room options

Frequently asked questions

The Schluter®-Shower System is an integrated family of products that creates a "sealed" system for tiled showers, steam showers, steam rooms, and bathtub surrounds. It is designed to be durable, water-tight and easy to install.

The Schluter®-Shower System offers several benefits over traditional shower construction methods. These include: * It is more durable and less prone to leaking * It is easier to install and maintain * It is more aesthetically pleasing * It offers greater flexibility in design.

The Schluter®-Shower System consists of a variety of components, including a waterproofing membrane, a drain, a base, a curb, a bench, and a niche. The specific components you need will depend on the size, shape, and functionality of your shower.

The installation of the Schluter®-Shower System is detailed in the Schluter®-Shower System Installation Handbook. This handbook provides step-by-step instructions for installing each component of the system.

The Schluter®-Shower System is backed by a limited lifetime warranty. The warranty covers defects in materials and workmanship. Please refer to the warranty information for specific details.

Schluter

-Shower System Installation Handbook 2015

Bonded Waterproofing System for Tiled Showers,

Steam Showers, Steam Rooms, and Bathtub Surrounds

Schluter ® -Shower System

Bonded Waterproofing System for Tiled Showers,

Steam Showers, Steam Rooms, and Bathtub Surrounds

The Traditional Tiled Shower System

Schluter

-Shower System

Schluter

-Systems’ written installation instructions shall have precedence over referenced industry

CONTENTS

SHOWER SELECTION GUIDE

SHOWER ASSEMBLY

4

6

8

10 Barrier-free showers

STEAM SHOWER ASSEMBLY

STEAM ROOM ASSEMBLY

INSTALLATION

BATHTUB SURROUND

12

14

16

18 Bathtub surround assembly

20 Walls and ceilings

21

22 Shower base with

26 Shower base with

31 Bathtub surround

33 Accessibility and style

34 Security and utility

BARRIER-FREE SHOWERS

THE WATERPROOF BATHROOM

PROFILES

THIN-SET FACTS

TESTING, LISTINGS,

& APPROVALS

MOLD

VAPOR

PRODUCT & ORDERING INFO

WARRANTY

35 Details make the difference

36 Discussion on thin-set mortar types to be used

with

37 Products and system evaluation

38 The importance of mold control

39 The importance of water vapor management

40

47

SHOWER SELECTION GUIDE

Beautiful, durable, functional

Waterproofing options

Drain options

Shower base options

4 SHOWER SELECTION GUIDE

Curb options

Bench options

Shower niche

SHOWER SELECTION GUIDE 5

SHOWER ASSEMBLY

Showers – Ceramic or stone tile

Schluter

-KERDI waterproofing membrane

K-SH-K-15

6 SHOWER ASSEMBLY — Schluter

-KERDI waterproofing membrane

Showers – Ceramic or stone tile

Schluter

-KERDI waterproofing membrane

K-SH-K-15

SHOWER ASSEMBLY — Schluter

-KERDI waterproofing membrane 7

SHOWER ASSEMBLY

Showers – Ceramic or stone tile

Schluter

-KERDI-BOARD waterproof building panel

K-SH-KB-15