Memorex Mi4390 User guide

Clock Radio
Dual Alarm
Rise and Shine
User Guide
Please read these instructions completely,
before operating this product.
Guía del usario
Por favor lea toda las instruciones antes
de tratar de usar este producto.
memorex.com
Mi4390
SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
DANGEROUS VOLTAGE:
The lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to the
presence of uninsulated dangerous voltage within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
ATTENTION:
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
FCC WARNING:
This equipment may generate or use radio frequency energy. Changes
or modifications to this equipment may cause harmful interference unless
the modifications are expressly approved in the instruction manual. The
user could lose the authority to operate this equipment if an unauthorized
change or modification is made.
ATTENTION:
POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA
PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE
LA PRISES ET POUSSER JUSQU’AU FOND.
iPod is a trademark of Apple Computer, Inc., registered in the U.S.
and other countries.
1
SAFETY PRECAUTIONS
INFORMATION:
This equipment complies with Class B digital device regulations.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
WARNING: TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.
SURGE PROTECTORS:
It is recommended to use a surge protector for AC connection.
Lightning and power surges ARE NOT covered under warranty
for this product.
This Class B digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe B est conforme à la
norme NMB-003 du Canada.
2
Dear Customer:
Selecting fine audio equipment such as the unit you’ve just purchased is only the start
of your musical enjoyment. Now it’s time to consider how you can maximize the fun
and excitement your equipment offers. This manufacturer and the Electronic Industries
Association’s Consumer Electronics Group want you to get the most out of your
equipment by playing it at a safe level. One that lets the sound come through loud and
clear without annoying blaring or distortion and, most importantly, without affecting your
sensitive hearing.
Sound can be deceiving. Over time your hearing “comfort level” adapts to higher volumes
of sound. So what sounds “normal” can actually be loud and harmful to your hearing.
Guard against this by setting your equipment at a safe level BEFORE your hearing adapts.
To establish a safe level:
• Start your volume control at a low setting.
• Slowly increase the sound until you can hear it comfortably and clearly, and
without distortion.
Once you have established a comfortable sound level:
• Set the dial and leave it there.
Taking a minute to do this now will help to prevent hearing damage or loss in the future.
After all, we want you listening for a lifetime.
We Want You Listening For A Lifetime
Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since
hearing damage from loud noise is often undetectable until it is too late, this manufacturer
and the Electronic Industries Association’s Consumer Electronics Group recommend you
avoid prolonged exposure to excessive noise. This list of sound levels is included for
your protection.
Decibel
Level
30
40
50
60
70
80
Example
Quiet library, soft whispers
Living room, refrigerator, bedroom away from traffic
Light traffic, normal conversation, quiet office
Air conditioner at 20 feet, sewing machine
Vacuum cleaner, hair dryer, noisy restaurant
Average city traffic, garbage disposals, alarm clock at two feet
THE FOLLOWING NOISES CAN BE DANGEROUS UNDER
CONSTANT EXPOSURE:
C
IND
R
NI
U
EIA
EST. 1924
S
N
S
O
O C I A TI
IES
3
O
A
Information courtesy of the Deafness Research Foundation.
We
Want You
LISTENING
For A Lifetime
ELECT
Subway, motorcycle, truck traffic, lawn mower
Garbage truck, chain saw, pneumatic drill
Rock band concert in front of speakers, thunderclap
Gunshot blast, jet engine
Rocket launching pad
TR
90
100
120
140
180
S
LOCATION OF CONTROLS
FRONT/TOP
17
1
9
2
10 11
3
4
5
12
6
13
7
14
15
8
16
9. Power Button
10.Play/Pause (®p) Button
11.Remote Sensor
12.SNOOZE/Dimmer Button
13.Display
14.Battery Compartment
(Bottom of Unit)
(Battery cover Part
No. 4622-05268-0010*)
15.MODE Button
16.Volume –/HR (Hour) +
Button
17.Speakers
1. TIME SET/Tune/Skip/
Search Down o Button
2. ALARM SET/Tune/Skip/
Search Up n Button
3. FM Wire Antenna (Rear of
Unit)
4. LINE IN Jack (Rear of Unit)
5. iPod Compartment with
Connector (for use with
Universal Docks)
6. DC 9V Jack (Rear of Unit)
(AC Adapter Part No.
2295-05268-E300*)
7. ALARM Button
8. Volume +/MIN (Minute) +
Button
*Consumer Replaceable Part
(See page 18 to order.)
4
LOCATION OF CONTROLS (CONTINUED)
REMOTE
6
1
7
2
8
3
9
4
10
5
11
12
1.
2.
3.
Power Button
VOL (Volume) –/HR
(Hour) + Button
TIME SET/Tune/Skip/
Search Down o Button
4. Play/Pause (®p) Button
5. DIMMER Button
6. Remote Transmitter (Top
of Unit)
7. MODE Button
8. VOL (Volume) +/MIN
(Minute) + Button
9. ALARM SET/Tune/Skip/
Search Up n Button
10.MUTE Button
11.SLEEP Button
12.Battery Compartment
(Rear of Unit)
Remote control Part No. 2239-04443-E000*
*Consumer Replaceable Part (See page 18 to order.)
NOTE:
The remote buttons function in the same way as the buttons on the
main unit.
5
POWER SOURCE
AC CONNECTION
Insert the small end of the AC adapter
into the DC IN jack (located on the rear
of the unit). Connect the other end to a
wall outlet having 120V AC, 60 Hz.
AC Adapter, DC 9V Z
NOTES:
• Remove both the DC plug and the
AC-IN plug to disconnect the AC adapter when not in use.
• Only use the supplied AC adapter which has the following specs:
DC 9V Z
BATTERY INSTALLATION
Two (2) “AAA” size batteries can also be
used to provide a back-up for the clock and
alarm time for this unit as follows:
1. Open the battery door by pushing in on
the tab, then removing the door.
2. Insert two (2) “AAA” batteries as shown.
Alkaline batteries are recommended for
the longest playing time.
front of unit
3. Place the battery door back on the
compartment.
NOTES:
• The batteries are used to back-up the clock and alarm times when the
AC adapter is disconnected or there is a power failure.
• The battery indicator will appear or blink in the display when there are
no batteries, or the batteries are low and need replacing.
IMPORTANT! See Battery Precautions on the next page.
6
POWER SOURCE (CONTINUED)
REMOTE BATTERY INSTALLATION
CR 2 0 2 5
1.
Remove the Battery Compartment by
pressing in on the tab and then sliding the
compartment out.
2.
Install a CR2025 battery by popping it
in through the back of the compartment,
paying attention to the polarity diagram in
the compartment (positive side up).
3.
Replace the Battery Compartment.
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this device:
1.
Warning–Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type.
2.
Use only the size and type of batteries specified.
3.
Be sure to follow the correct polarity when installing the batteries as indicated
in the Battery Compartment. A reversed battery may cause damage to
the device.
4.
Do not mix different types of batteries together (e.g. Alkaline, Rechargeable and
Carbon-zinc) or old batteries with fresh ones.
5.
If the device is not to be used for a long period of time, remove the batteries to
prevent damage or injury from possible battery leakage.
6.
Do not try to recharge a battery not intended to be recharged; it can overheat and
rupture. (Follow battery manufacturer’s directions.)
OPTIONAL CONNECTION
LINE IN JACK (REAR OF UNIT)
Insert one end of the audio cable (not included) into the LINE OUT jack on
your external audio unit and the other end into the LINE IN jack on the rear of
this unit.
To listen to the external audio unit, turn this unit on using the Power button,
and turn on the external unit as well. Repeatedly press the MODE button to
select LINE IN mode; “LINE IN” will appear in the display. The external audio
unit’s output sound will be heard through this unit’s speakers. If you wish to
listen to the iPod in the iPod compartment, repeatedly press the MODE button
to select iPod mode; iPod will appear in the display.
NOTE: If this unit is turned on and in FM/iPod mode, once the external unit is
connected, this unit will change to LINE IN mode automatically. Then, if you
disconnect the external unit from the LINE IN jack, this unit will revert back to
FM/iPod mode.
7
INSERTING AN iPod
1
2
(B)
(A)
(A)
Insert the Universal Dock
included with your iPod (A) into
the iPod compartment (B) (as
shown), making sure the tabs
are facing front, and slip the
tabs into place. Press the rear
side of the Universal Dock until
it is positioned inside the iPod
compartment.
(B)
Slide the iPod (A) into the
Universal Dock (B) (as shown).
Gently push down so the
connector on the iPod slides onto
the connector on this unit.
NOTES:
• If this unit is turned on and in
FM/LINE IN mode, once the
iPod is connected, this unit
will change to iPod mode
automatically.
• When the iPod is connected to
this unit, it will be in the Pause
mode.
• To remove the Universal Dock,
insert your finger (or other
object) into the gap in the
Universal Dock, then gently
pull the Universal Dock out to
remove it.
• CHARGING: When the iPod is
inserted into the dock, whether
this unit is on or off, the iPod’s
battery will charge until it is full.
• You will not be able to select
iPod or LINE IN mode if there
is no device or iPod connected
to the LINE IN jack or the iPod
dock.
3
The iPod will charge as long as
this unit is connected with the
AC adapter.
Please see the next page for
instructions on using an iPod with
this unit.
8
OPERATION
USING AN iPod WITH THIS UNIT
1
1
2
2
With an iPod connected (see previous
page), if this unit is not already on,
turn this unit on by pressing the
Power button 1. Repeatedly press
the MODE button
2 to select
iPod mode; “iPod” will appear in the
display.
You can operate the iPod
using its own controls, as per
its owner’s manual, or you can
use the controls on this unit to
operate the iPod.
NOTE: The iPod’s menu functions
can only be accessed on the iPod
itself.
3
4
To play/pause the iPod:
Press the Play/Pause (®p) button
to start playback on your iPod.
Press again to pause playback
and press yet again to resume
playback.
To skip forward or backward on
the iPod: Press the Tune/Skip/
Search Down o 1 or Up n 2
button to skip to the beginning of
the current track/previous or next
track.
To search forward or backward
on the iPod: Press and hold the
Tune/Skip/Search Down o 1 or
Up n 2 button to search within the
currently-playing track.
1
NOTES:
•
See the next page for how to adjust the volume.
•
To turn this unit off, press the Power button.
9
2
OPERATION (CONTINUED)
ADJUSTING THE VOLUME
1
2
1
1
To mute the sound:
Press the MUTE button once
to mute the sound and again to
resume previous volume level.
To adjust the main volume:
Press the VOL +/MIN + 1 or VOL
–/HR + 2 button to increase or
decrease the volume.
NOTES:
•
After you have adjusted the volume setting, if you turn the unit off and
then on again, the volume level will be set to the level you selected
prior to turning the unit off.
•
To turn this unit off, press the Power button.
10
OPERATION (CONTINUED)
USING THE FM RADIO
1
2
Turn this unit on by pressing the
Power button.
Repeatedly press the MODE button
to select the FM Radio mode;
“RADIO” will appear in the display.
3
1
2
Repeatedly press the Tune/ Skip/
Search Down o 1 or Up n 2
button to manually advance the
frequency in the display up or down
until the desired frequency appears.
For auto tuning, press and hold the
Tune/Skip/Search Down o 1 or
Up n 2 button until the frequency
in the display starts to scan and
then release; the tuner will search
and then stop on the next strong
station it finds. Repeat this step until
the desired frequency appears in
the display.
NOTES:
• When a station is tuned,
after three seconds, the radio
frequency will disappear and
the actual time will reappear in
the display.
• See the previous page for how
to adjust the volume.
• To turn this unit off, press the
Power button.
• If a strong stereo signal is
broadcast, the Stereo (ST)
indicator will light.
Antenna:
Connect the FM wire to the FM antenna jack, unravel and extend the FM
wire antenna for best reception.
11
OPERATION (CONTINUED)
TO SET OR RESET THE ACTUAL TIME
Follow the instructions below to manually set the time.
2
1
2
1
Press the Volume +/MIN +
button 1 to set the Minute and
the Volume –/HR + button 2 to
set the hour. Make sure to set the
correct AM/PM setting.
NOTE: There is no indicator for
AM in the display.
With the power off, press the TIME
SET/Tune/Skip/Search Down o
button; the time will blink.
3
Press the TIME SET/Tune/Skip/
Search Down o button (or wait
approx. 15 seconds) and the time
will be set.
12
OPERATION (CONTINUED)
TO SET OR RESET THE ALARM TIME
2
1
3
2
1
With the power off, press the
ALARM SET/Tune/Skip/Search
Up n button; the Alarm time will
blink in the display.
Press the Volume +/MIN +
button 1 to set the alarm minute
and the Volume –/HR + button
2 to set the alarm hour. Make
sure to set the correct AM/PM
setting. Press the ALARM SET/
Skip/Search Up n button 3 again.
3
4
3
2
1
The volume setting will appear
in the display. Select a desired
maximum volume level (level 0 to
15) to wake to using the Volume
+/MIN + button 1 to set the alarm
minute and the Volume –/HR +
button 2. Press the ALARM SET/
Skip/Search Up n button 3 again
(or wait approx. 5 seconds) to
save your settings.
Repeatedly press the ALARM
button to select alarm off, alarm
on for iPod, alarm on for Radio or
Alarm on for Buzzer.
NOTE:
Make
sure
the
corresponding indicator (iPod,
RADIO or BUZZER) appears in
the display.
CONTINUED ON THE NEXT PAGE
13
OPERATION (CONTINUED)
5
6
1
2
If set to Radio (in Step 4), then
while the frequency is blinking,
set the frequency using the Tune/
Skip/Search Down o 1 or Up n
2 button.
NOTE: When the alarm time is
reached, the unit will turn on the
frequency that you selected.
If set to iPod (in Step 4), insert the
iPod as shown on page 8. Select your
desired track and then make sure
both your iPod and this unit are turned
off. When the alarm time is reached,
this unit will start playback on the
track that you selected and the tracks
following it in the playlist. This unit
will playback for 59 minutes then turn
off automatically or, if the remaining
playlist has less than 59 minutes of
playback time remaining, this unit will
just playback the remaining time of
the playlist and then stop.
NOTES:
• When the actual time matches the selected preset alarm time, if set to Buzzer
or Radio, the unit will automatically turn on for 59 minutes and then shut off. If
set to iPod, the unit will start playback on the track that you selected and the
tracks following it in the playlist. (See Step 6 above.)
• When the alarm time is reached, the alarm volume level will be set to the
minimum (Level 0) and it will increase one level continuously until the desired
maximum volume level (see Step 3 on the previous page) is reached.
• While the alarm is on, if you press any button on the unit (except the
SNOOZE/DIMMER button or the Power button), the unit will change from
Alarm mode to normal Power On mode, so you can adjust any setting (i.e.,
volume level, radio frequency, etc.) as desired.
• To shut off the alarm, see TO SHUT THE ALARM OFF section on
the next page.
14
OPERATION (CONTINUED)
TO SHUT THE ALARM OFF
1
1
2
Press the Power button 1 or
ALARM button 2 and the alarm
will turn off and be set for the next
day. To NOT set the alarm for the
next day, press the ALARM button
2 repeatedly to select Alarm Off
(no indicator in the display).
SNOOZE
1
While the alarm is sounding,
press the SNOOZE/DIMMER
button; the SNOOZE indicator will
blink in the display. The alarm will
turn back on automatically ten
minutes later until the SNOOZE
function is cancelled.
NOTE:
•
To cancel the SNOOZE function (the alarm will not turn back on),
press the ALARM button–the SNOOZE indicator will disappear from
the display–and repeatedly press to select between Alarm On for
Buzzer or iPod (alarm will be set for next day) or Alarm Off (alarm
will not be set for the next day).
15
OPERATION (CONTINUED)
SLEEP
DIMMER
1
1
With the unit in the LINE IN , Radio or
iPod mode, press the SLEEP button
on the remote; “00” will appear in the
display for about five seconds.
Repeatedly press the SLEEP button to
turn the SLEEP feature on (“SLEEP”
will appear in the display) and select a
SLEEP time, 15-90 minutes (i.e., “30”–
turns off automatically after 30 minutes,
“45”–turns off automatically after 45
minutes, etc.).
After about five seconds, the SLEEP
time will disappear from the display. To
view the remaining SLEEP time, press
the SLEEP button once.
NOTE: To cancel the SLEEP function,
repeatedly press the SLEEP button until
the “SLEEP” indicator disappears from
the display and the “00” briefly appears
in the display.
Press the DIMMER button on the
remote (shown) or the SNOOZE/
Dimmer button on the main unit
(can only be used when the alarm
is not sounding or not in snooze
mode) repeatedly to adjust the
brightness of the display.
16
TROUBLESHOOTING GUIDE
If you experience a problem with this unit, check the chart below before
calling for service.
SYMPTOM
CAUSE
SOLUTION
No sound.
Volume is set to
Increase volume.
minimum.
FM: no sound.
Power is not on or FM
Press the Power button, mode is not selected.
then the MODE button to select FM. Volume is set to Increase volume.
minimum.
FM: poor sound.
Station is not tuned
Retune the FM properly.
broadcast station.
FM wire antenna is
Extend FM wire
not extended.
antenna.
Incorrectly connected.
Check the connection.
iPod mode: no sound.
Not in iPod mode.
Press the MODE button.
Time reset to “12:00”.
Batteries connected
Check the batteries.
improperly, not
connected or dead.
Clock not set.
Set the clock.
Alarm does not
Alarm is not activated
Set and activate alarm as
turn on.
or set properly.
described on page 13. 17
SPECIFICATIONS
GENERAL:
Power Source . .................DC 9V Adapter (Center Positive)
Speaker............................................................... 2 x 4 ohms
Output Power ............................................................2 x 1W
Weight........................................................................ 0.91 lb
Dimensions.............................. 2.3” (H) x 6.4” (W) x 6.4” (D)
Weight and dimensions are approximate.
RADIO SECTION:
Frequency Range (FM) ................................ 87.5–108 MHz
Specifications are subject to change without notice.
For additional set-up or operating assistance, please
visit our WEBSITE at:
WWW.MEMOREX.COM
FOR CONSUMER REPLACEABLE PART(S), SEE PART NUMBER(S)
ON PAGES 4 AND 5 AND THEN CONTACT FOX INTERNATIONAL AT:
1-800-321-6993.
18
Imation Electronic Products,
A Division of Imation Enterprises Corp.,
Weston, Florida. Printed in China
memorex.com
Memorex and the Memorex logo are trademarks
of Imation Corp. and its affiliates.
Imation Electronic Products,
Una division de Imation Enterprises Corp.,
Weston, Florida. Impreso en China
memorex.com
Memorex y el logo de Memorex son una marca
registrada de Imation Corp. y sus empresas afiliadas.